Compact Thick Film Chip Resistors MCR03 (0603 size : 1 / 10W) Features 1) Power rating of 1 / 10W 2) Highly reliable chip resistor Ruthenium oxide dielectric offers superior resistance to the elements. 3) Electrodes not corroded by soldering Thick film makes the electrodes very strong. 4) Resin protective coating absorbs impact, facilitates mounting. 5) ROHM resistors have approved ISO9001- / ISO/TS 16949- certification. Ratings Design and specifications are subject to change without notice. Carefully check the specification sheet supplied with the product before using or ordering it. Item Rated power Conditions Specifications Power must be derated according to the power derating curve in Figure 1 when ambient temperature exceeds 70°C. 0.10W (1 / 10W) at 70°C 100 POWER LOAD (%) 80 60 40 20 0 −55 0 70 100 155 AMBIENT TEMPERATURE (°C) Fig.1 Rated voltage The voltage rating is calculated by the following equation. If the value obtained exceeds the limiting element voltage, the voltage rating is equal to the maximum operating voltage. E= Nominal resistance P×R E: Rated voltage (V) P: Rated power (W) R: Nominal resistance (Ω) Limiting element voltage 50V See Table 1. −55°C to +155°C Operating temperature www.rohm.com c 2011 ROHM Co., Ltd. All rights reserved. ○ 1/4 2011.06 - Rev.N MCR03 (0603 size : 1 / 10W) Data Sheet Table 1 Jumper type Resistance Max. 50mΩ Rated current Resistance range (Ω) Resistance tolerance 1A J (±5%) Operating temperature −55°C to +155°C FX (±1%) D (±0.5%) Resistance temperature coefficient (ppm/°C) 1.0 to 9.1 (E24) ±400 10 to 10M (E24) ±200 10 to 10M (E24,96) ±100 10 to 91 (E24) ±100 100 to 1M (E24) ±50 Characteristics Item Resistance Guaranteed value Resistor type Jumper type J : ±5% FX : ±1% D: ±0.5% Variation of resistance with temperature Overload Solderability Resistance to soldering heat Rapid change of temperature Max. 50mΩ JIS C 5201-1 4.5 JIS C 5201-1 4.8 Measurement : +25 / +125°C See Table.1 ± (2.0%+0.1Ω) JIS C 5201-1 4.13 Rated voltage (current) ×2.5, 2s. Limiting element voltage×2 : 100V Max. 50mΩ A new uniform coating of minimum of 95% of the surface being immersed and no soldering damage. JIS C 5201-1 4.17 Rosin·Ethanol (25%WT) Soldering condition : 235±5°C Duration of immersion : 2.0±0.5s. ± (1.0%+0.05Ω) Max. 50mΩ No remarkable abnormality on the appearance. JIS C 5201-1 4.18 Soldering condition : 260±5°C Duration of immersion : 10±1s. ± (1.0%+0.05Ω) Max. 50mΩ JIS C 5201-1 4.19 Test temp. : −55°C to +125°C 5cyc ± (3.0%+0.1Ω) Max. 100mΩ JIS C 5201-1 4.24 40°C, 93%RH Test time : 1,000h to 1,048h ± (3.0%+0.1Ω) Max. 100mΩ JIS C 5201-1 4.25.1 Rated voltage (current), 70°C 1.5h : ON − 0.5h : OFF Test time : 1,000h to 1,048h ± (3.0%+0.1Ω) Max. 100mΩ JIS C 5201-1 4.25.3 155°C Test time : 1,000h to 1,048h ± (1.0%+0.05Ω) Max. 50mΩ JIS C 5201-1 4.29 23±5°C, Immersion cleaning, 5±0.5min. Solvent : 2-propanol Damp heat, steady state Endurance at 70°C Endurance Resistance to solvent Bend strength of the end face plating Test conditions (JIS C 5201-1) Max. 50mΩ ± (1.0%+0.05Ω) Without mechanical damage such as breaks. www.rohm.com c 2011 ROHM Co., Ltd. All rights reserved. ○ 2/4 JIS C 5201-1 4.33 2011.06 - Rev.N MCR03 (0603 size : 1 / 10W) Data Sheet Dimensions (Unit : mm) No. 1 0.3±0.2 2 3 0.45±0.1 0.3±0.2 1.6±0.1 4 Resistive element 2 Silver thick film electrode 3 Nickel electrode 4 Sn electrode 5 Alumina substrate 6 Overcoating (Resin) 0.8±0.1 5 Material 1 6 Packaging Reel Taping P0 P2 P1 φD0 E F W B0 02 04 06 08 06 04 D 02 B 08 A0 A Heat crimp cover Tape Thick paper mount (Underside paper tape) Chip resistor Square punchout hole T2 (Unit : mm) W 8.0±0.3 C D0 +0.1 0 Label EIAJ ET-7200B compliant φ1.5 F E A0 B0 3.5±0.05 1.75±0.1 1.1±0.1 1.9±0.1 P0 P1 P2 T2 4.0±0.1 4.0±0.1 2.0±0.05 Max. 1.1 (Unit : mm) A B C Narrow pitch (2mm pitch) version D P0 φ180 0 −3 φ60 +1 0 9 +1.0 0 P2 φ13±0.2 P1 φD0 E F W B0 Bulk case A0 Thick paper mount Heat crimp cover Tape (Underside paper tape) Chip resistor Square punchout hole Slider Shutter T2 12.0±0.1 36 0 −0.2 W 8.0±0.3 D0 +0.1 0 φ1.5 110±0.7 EIAJ ET-7200B compliamt www.rohm.com c 2011 ROHM Co., Ltd. All rights reserved. ○ (Unit : mm) F E A0 B0 3.5±0.05 1.75±0.1 1.1±0.1 1.9±0.1 P0 P1 P2 T2 4.0±0.1 2.0±0.5 2.0±0.05 Max. 1.1 (Unit : mm) 3/4 2011.06 - Rev.N MCR03 (0603 size : 1 / 10W) Data Sheet Part No. Explanation M C R 0 3 Part No. E Z P J Resistance tolerance Nominal resistance D FX J ±0.5% ±1% ±5% J is also used for jumper Resistance code, 3 or 4 digits. 000 denotes jumper type. Resistance Resistance tolerance code FX, D J : : 4 digits 3 digits Packaging Specifications Code Part No. Code MCR03 MCR03 MCR03 EZP MZP PZPI Resistance tolerance J(±5%) FX(±1%) D(±0.5%) − − Packaging specifications Reel Basic ordering unit (pcs) Remarks Paper tape (4mm Pitch) Paper tape (2mm Pitch) Bulkcase φ180mm(7inch) φ180mm(7inch) − 5,000 10,000 25,000 Narrow pitch type − − Reel (φ180mm) : Compatible with JEITA standard "EIAJ ET-7200B" : Standard product www.rohm.com c 2011 ROHM Co., Ltd. All rights reserved. ○ 4/4 2011.06 - Rev.N Notice Notes No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage. The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices). The Products specified in this document are not designed to be radiation tolerant. While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons. Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual. The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuelcontroller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing. If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. R1120A