SPECIFICATION FOR APPROVAL 20080131-D REF : 20070313-B PROD. NAME PAGE: 1 ABC'S DWG NO. WOUND CHIP INDUCTOR CC3225□□□□L□-□□□ ABC'S ITEM NO. Ⅰ﹒CONFIGURATION & DIMENSIONS： 100 Marking Inductance code 2.9±0.2 A : 3.2±0.4 m/m B : 2.5±0.2 m/m C : 2.2±0.2 m/m E : 1.0±0.2 : 0.6 +0.3 -0 m/m m/m +0 ※ △ K=∣K1-K2∣=0.25 m/m 1.4 C F F F A K1 E K2 B 1 1.8 1 （ PCB Pattern ） Ⅱ﹒SCHEMATIC DIAGRAM： d a Ⅲ﹒MATERIALS： a﹒Core：Ferrite DR core c b﹒Wire ：Enamelled copper wire (class H) c﹒Terminal：Cu/Sn b d﹒Encapsulate：Epoxy novolac molding compound e﹒Remark：Products comply with RoHS' requirements Reflow profile Peak Temp：250℃ max. Max time above 245℃ ：20~40sec max. Max time above 217℃ ：60~150sec max. 200℃~250℃ Average Ramp-up Rate：3℃/second max. Ⅳ﹒GENERAL SPECIFICATION： a﹒Temp. rise ：20℃ max. b﹒Ambient temp.：100℃ max. Temperature Rising Area Preheat Area c﹒Storage temp.：-40℃ ----+125℃ d﹒Operating temp.：-40℃----+125℃ f﹒Rated current：Current cause inductance drop within 10% g﹒Resistance to solder heat：260℃.10 secs. Forced Cooling Area 6 ℃ / second max. Peak Temperature： 250℃ 250 245 Temperature ( ℃ ) e﹒Terminal pull strength：1.5 kg min. Reflow Area 150 ~ 200 ℃ / 60 ~ 180sec 20~40sec 217 200 60~150sec 150 100 50 h﹒Resistance to solvent：Per MIL-STD-202F 0 AR-001A 50 100 150 Time ( seconds ) 200 250 20080131-D REF : 20070313-B PROD. SPECIFICATION FOR APPROVAL PAGE: 2 NAME CC3225□□□□L□-□□□ ABC'S DWG NO. WOUND CHIP INDUCTOR ABC'S ITEM NO. Ⅴ﹒ELECTRICAL CHARACTERISTICS： 7.96 7.96 7.96 7.96 SRF ( MHz ) min. 100 80 65 55 RDC (Ω) max. 0.156 0.195 0.260 0.325 7.96 7.96 2.52 2.52 45 35 28 25 0.520 0.650 1.105 1.690 2.52 2.52 2.52 2.52 2.52 2.52 0.796 20 17 15 13 10 9 8 2.600 3.000 3.640 5.460 8.450 8.710 10.140 DWG No. Inductance ( µH ) Q min. Test Freq ( MHz ) CC32251R0ML□-□□□ CC32251R5ML□-□□□ CC32252R2ML□-□□□ CC32253R3ML□-□□□ CC32254R7ML□-□□□ CC32256R8ML□-□□□ CC3225100KL□-□□□ CC3225150KL□-□□□ CC3225220KL□-□□□ CC3225270KL□-□□□ CC3225330KL□-□□□ CC3225470KL□-□□□ CC3225680KL□-□□□ CC3225820KL□-□□□ CC3225101KL□-□□□ 1.00±20% 1.50±20% 2.20±20% 3.30±20% 4.70±20% 6.80±20% 10.00±10% 15.00±10% 22.00±10% 27.00±10% 33.00±10% 47.00±10% 68.00±10% 82.00±10% 100.00±10% 10 10 10 10 10 10 15 15 15 15 15 20 20 20 20 1). □：Packaging information… A：Bulk 2). "- AR-001A □□□ ":Reference code B：Taping Reel IDC ( mA ) max. 770 580 480 400 320 280 220 180 145 125 115 105 85 80 75 SPECIFICATION FOR APPROVAL 20080131-D REF : 20070313-B PROD. NAME PAGE: 3 ABC'S DWG NO. WOUND CHIP INDUCTOR CC3225□□□□L□-□□□ ABC'S ITEM NO. Ⅵ﹒CURVE： @ Inductance VS. DC Superposition Characteristics 10 7 5 2 101K 3 330K Inductance (uH) 2 10 1 7 5 100K 3 2 1R5M 10 0 7 5 3 2 10 1 2 5 7 10 2 3 2 5 7 10 3 3 2 5 7 10 3 3 DC Current (mA) @ Q VS. Frequency Response 100 90 80 70 60 330K 101K Q 50 100K 40 30 20 1R5M 10 -1 10 2 4 6 0 8 10 2 Frequency (MHz) AR-001A 4 6 1 8 10 2 4 SPECIFICATION FOR APPROVAL 20080131-D REF : 20070813-C PROD. NAME PAGE: 4 ABC'S DWG NO. WOUND CHIP INDUCTOR CC3225□□□□L□-□□□ ABC'S ITEM NO. Ⅶ﹒PACKAGING INFORMATION： ( 1 ) Configuration T Cover Tape N A B 2.0±0.5 ∮C ∮C D Embossed Carrier G ※ Carrier Tape Width : D 4 m/m Leader no component 200 m/m min. 100 100 100 100 100 Start 100 100 100 P:4 m/m End Trailer no component 400 m/m min. Components User direction of feed ※ There is no differentiation or directions of polarity ( marking ) in the packaging method. ( 2 ) Dimensions Unit:m/m Style A 07 - 08 178 13 - 12 330 B C D G N T 21±0.8 13 8 13 12 50 -0 50 -0 12.5 21±0.8 10 +0 10 +0 18.4 ( 3 ) Q'TY & G.W. Per package Inner : Reel Series AR-001A Q'TY (pcs) G.W. (gw) Outer : Carton Style Q'TY (pcs) G.W. (Kg) Size (cm) CC3225 1,000 110 07 - 08 50,000 7.50 41 x 39 x 22 CC3225 2,000 220 07 - 08 100,000 15.00 41 x 39 x 22 CC3225 7,000 770 13 - 12 168,000 25.20 41 x 39 x 22 SPECIFICATION FOR APPROVAL REF : 20080131-D PROD. PAGE: 5 ABC'S DWG NO. WOUND CHIP INDUCTOR NAME CC3225□□□□L□-□□□ ABC'S ITEM NO. Ⅷ﹒DWGING NUMBER EXPRESSION： C C 3 2 2 5 Reference code Appendix code 2 : Package Appendix code 1 : Classification Tolerance code Electrical code Dimension code Type code Appendix code 1：Product Classification L：Lead Free Standard products comply with RoHS' requirements 1 ~ 9：Lead Free Special products comply with RoHS' requirements Appendix code 2：Package Information Inner package Code Inner package Q'TY Remark A Bag 1000 pcs B T / R ( Reel package ) 1000 pcs C T / R ( Reel package ) 2000 pcs [ anti-static ] D T / R ( Reel package ) 7000 pcs Hot-press E T / R ( Reel package ) 1000 pcs [ anti-static ] F T / R ( Reel package ) 2000 pcs Note： 1 package code "B" &"C" & "E" ： 100 100 100 100 100 100 Start 100 End 200 -0 m/m 450-0 m/m Note： 2 package code "F" ： End 200 -0 m/m AR-001A 100 100 100 100 100 100 100 Start 160+0 m/m SPECIFICATION FOR APPROVAL 20080131-D REF : 20070115-A PROD. NAME PAGE: 6 WOUND CHIP INDUCTOR ABC'S DWG NO. CC3225□□□□L□-□□□ ABC'S ITEM NO. Ⅸ﹒RELIABILITY TEST： Test item Specification Test condition / Test method Electrical performance test Inductance L Q Self resonance frequency SRF DC Resistance RDC □HP4194A with HP-16034E test fixture Refer to standard electrical characteristic list Rated current IDC □HP4291A with HP-16093A test fixture CH-502AC Applied the current to coils，The Inductance change shall be less than 10% to initial value & temperature rise shall not be more than 20℃ 1﹒Applied the allowed DC current for 10 minutes 2﹒Temperature measure by digital surface thermometer Temperature rise test 20℃ max. Over load test After test，Inductors shall be no evidence of electrical and mechanical damage Applied 2 times of rated allowed DC current to inductor for a period of 5 minutes Withstanding voltage test After tset，Inductors shall be no evidence of electrical and mechanical damage AC voltage of 1000VAC applied between inductors terminal and coating for 5 seconds Insulation resistance test 1000 MΩ min﹒ 100 VDC applied between inductor terminal and coating Mechanical performance test Vibration test ( Low frequency ) 1﹒Inductors shall be no evidence of electrical and mechanical damage 1﹒Amplitude：1.5 m/m 2﹒Frequency：10 -- 55 -- 10 Hz / 1min. 3﹒Direction：X，Y，Z 4﹒Duration：2 hrs / X，Y，Z Shock test 2﹒Inductance shall not change more than±5% Inductors shall be dropped 10 times from a height of 1m onto 3cm wooden board Resistance to soldering heat 3﹒Q Shall not change more than ±20% Temp：260±5℃ Time：10±1.0 sec. AR-001A SPECIFICATION FOR APPROVAL REF : 20070115-A 20080131-D PROD. NAME PAGE: 7 WOUND CHIP INDUCTOR ABC'S DWG NO. CC3225□□□□L□-□□□ ABC'S ITEM NO. Terminal strength-pull test Terminal shall not be loosened or ruptured A 0.5kg load shall be applied to both Terminals in the axis direction for 1 minute﹒ Solderability test The terminal shall be at least 90% covered with solder After fluxing，Inductor shall be dipped in a melted solder bath at 240±5℃ for 5 seconds﹒ Resistance to solvent test There shall be no case deformation change in appearance or obliteration of marking MIL-STD-202F，Method 215D Climatic test Temperature characteristic Humidity test Cold test 1﹒Inductors shall be no evidence of electrical and mechanical damage 2﹒Inductance shall not change more than ±10% 3﹒Q shall not change more than ±20% Thermal shock test Dry heat test High temperature load life test Humidity load life There shall be no evidence of short or open circuiting -40℃ -- +125℃ 1﹒Temp：40±2℃ 2﹒R.H.：90 -- 95% 3﹒Time：96±2 hours 1﹒Temp：-25±2℃ 2﹒Time：96±2 hours Room temp 15 mins Room temp 15 mins Total：5 cycles 1﹒Temp：85±2℃ 2﹒Time：96±2 hours 1﹒Temp：85±2℃ 2﹒Time：1000±12 hours 3﹒Load：Allowed DC current 1﹒Temp：40±2℃ 2﹒R.H.：90 -- 95% 3﹒Time：1000±12 hours 4﹒Load：Allowed DC current Note： Unless otherwise specified , Allow the specimen to stand at room temperature for 1 hour or more but not more than 2 hours , Measure the electrical and mechanical performances AR-001A -40±2℃ 30 mins +125±2℃ 30 mins SPECIFICATION FOR APPROVAL 20080131-D REF : 20070115-A PROD. NAME PAGE: 8 ABC'S DWG NO. WOUND CHIP INDUCTOR CC3225□□□□L□-□□□ ABC'S ITEM NO. Ⅹ﹒UL CARD： OBMW2 Magnet Wire-Comporent August 27, 1999 ELEKTRISOLA (MALAYSLA) SDN BHD IALAN DAMN SATU IANDA BAIK 28750 BENTONG, PAHANG DARUL MAKMUR MALAYSIA Mtl Dsg Mark Dsg BC Coating Type Estersol 160 E180 Amldester 200 Polysol-N 155 A200 PN155 Polyesterimide (solderable) Polyesterimide Polyurechane Polysol 155 P155 Polyurechane Polysol 155g Polysol 155p Polysol 160 Polysol 180 Polysol 170 Polysol-N 180 Pg155 Pp155,Gp155 P160 P180 P170 or G170 PN180 Polyurechane Polyurechane Polyurechane Polyurechane Polyurechane Polyurechane OC ____ ____ Nylon ____ ____ ____ ____ ____ ____ Nylon E143312 ANSI Typ Temp Class MW-77 180 MW-74 MW-80, MW-28 MW-79, MW-79 MW-79 MW-79 MW-79 MW-79 MW-79 ____ 200 155, 100 155, 130 130 155 155 155 156 180 Marking：Dompany name/nateriel designation or marked designation and factory identification on package ok reel See General Information preceding These Recognitions For use only in equipment where the acceptability of the combination is determined by Underwriters Laboratories Inc. OMFZ2 March 4, 1994 E59481 (S) BM-21 BM-22 BM-23 EME-1100 EME-1200 EME-5961C ALL ALL ALL 0.79 0.79 0.79 94HB 94HB 94V-0 50 50 50 50 50 50 50 50 50 BK BK BK BK BK BK 0.84 6.4 0.84 6.4 0.3 3.1 94V-0 94V-0 94V-0 94V-0 94V-0 94V-0 130 130 130 130 130 130 130 130 130 130 130 130 130 130 130 130 130 130 __________________ Reports: January 19, 1988: January 19, 1988: January 19, 1988: June 2, 1988; June 2, 1998; June 2, 1988. R AR-001A