NSC LM2574-3.3HVN Simple switcherâ ¢ 0.5a step-down voltage regulator Datasheet

LM2574/LM2574HV
SIMPLE SWITCHER™ 0.5A Step-Down Voltage Regulator
General Description
Features
The LM2574 series of regulators are monolithic integrated
circuits that provide all the active functions for a step-down
(buck) switching regulator, capable of driving a 0.5A load
with excellent line and load regulation. These devices are
available in fixed output voltages of 3.3V, 5V, 12V, 15V, and
an adjustable output version.
Requiring a minimum number of external components, these
regulators are simple to use and include internal frequency
compensation and a fixed-frequency oscillator.
The LM2574 series offers a high-efficiency replacement for
popular three-terminal linear regulators. Because of its high
efficiency, the copper traces on the printed circuit board are
normally the only heat sinking needed.
A standard series of inductors optimized for use with the
LM2574 are available from several different manufacturers.
This feature greatly simplifies the design of switch-mode
power supplies.
Other features include a guaranteed ± 4% tolerance on output voltage within specified input voltages and output load
conditions, and ± 10% on the oscillator frequency. External
shutdown is included, featuring 50 µA (typical) standby current. The output switch includes cycle-by-cycle current limiting, as well as thermal shutdown for full protection under
fault conditions.
n 3.3V, 5V, 12V, 15V, and adjustable output versions
n Adjustable version output voltage range, 1.23V to 37V
(57V for HV version) ± 4% max over line and load
conditions
n Guaranteed 0.5A output current
n Wide input voltage range, 40V, up to 60V for HV version
n Requires only 4 external components
n 52 kHz fixed frequency internal oscillator
n TTL shutdown capability, low power standby mode
n High efficiency
n Uses readily available standard inductors
n Thermal shutdown and current limit protection
Typical Application
Applications
n
n
n
n
Simple high-efficiency step-down (buck) regulator
Efficient pre-regulator for linear regulators
On-card switching regulators
Positive to negative converter (Buck-Boost)
(Fixed Output Voltage Versions)
DS011394-1
Note: Pin numbers are for 8-pin DIP package.
Patent Pending
SIMPLE SWITCHER™ is a trademark of National Semiconductor Corporation
© 1999 National Semiconductor Corporation
DS011394
www.national.com
LM2574/LM2574HV SIMPLE SWITCHER 0.5A Step-Down Voltage Regulator
June 1999
Connection Diagrams
8-Lead DIP
14-Lead Wide
Surface Mount (WM)
DS011394-2
* No internal connection, but should be soldered to PC board for best heat
transfer.
Top View
Order Number LM2574-3.3HVN, LM2574HVN-5.0,
LM2574HVN-12, LM2574HVN-15, LM2574HVN-ADJ,
LM2574N-3.3, LM2574N-5.0, LM2574N-12,
LM2574N-15 or LM2574N-ADJ
See NS Package Number N08A
www.national.com
DS011394-3
Top View
Order Number LM2574HVM-3.3, LM2574HVM-5.0,
LM2574HVM-12, LM2574HVM-15, LM2574HVM-ADJ,
LM2574M-3.3 LM2574M-5.0, LM2574M-12,
LM2574M-15 or LM2574M-ADJ
See NS Package Number M14B
2
Absolute Maximum Ratings (Note 1)
Lead Temperature
(Soldering, 10 seconds)
Maximum Junction Temperature
Power Dissipation
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Maximum Supply Voltage
LM2574
LM2574HV
ON /OFF Pin Input Voltage
Output Voltage to Ground
(Steady State)
Minimum ESD Rating
(C = 100 pF, R = 1.5 kΩ)
Storage Temperature Range
260˚C
150˚C
Internally Limited
Operating Ratings
45V
63V
−0.3V ≤ V ≤ +VIN
Temperature Range
LM2574/LM2574HV
Supply Voltage
LM2574
LM2574HV
−1V
−40˚C ≤ TJ ≤ +125˚C
40V
60V
2 kV
−65˚C to +150˚C
LM2574-3.3, LM2574HV-3.3
Electrical Characteristics
Specifications with standard type face are for TJ = 25˚C, and those with boldface type apply over full Operating Temperature Range.
Symbol
Parameter
Conditions
LM2574-3.3
LM2574HV-3.3
Typ
Units
(Limits)
Limit
(Note 2)
SYSTEM PARAMETERS (Note 3) Test Circuit Figure 2
VOUT
Output Voltage
VIN = 12V, ILOAD = 100 mA
VOUT
Output Voltage
3.3
4.75V ≤ VIN ≤ 40V, 0.1A ≤ ILOAD ≤ 0.5A
Output Voltage
4.75V ≤ VIN ≤ 60V, 0.1A ≤ ILOAD ≤ 0.5A
Efficiency
VIN = 12V, ILOAD = 0.5A
3.366
V(Max)
3.168/3.135
V(Min)
3.432/3.465
V(Max)
V
3.3
LM2574HV
η
V(Min)
3.3
LM2574
VOUT
V
3.234
3.168/3.135
V(Min)
3.450/3.482
V(Max)
%
72
LM2574-5.0, LM2574HV-5.0
Electrical Characteristics
Specifications with standard type face are for TJ = 25˚C, and those with boldface type apply over full Operating Temperature Range.
Symbol
Parameter
Conditions
LM2574-5.0
LM2574HV-5.0
Typ
Units
(Limits)
Limit
(Note 2)
SYSTEM PARAMETERS (Note 3) Test Circuit Figure 2
VOUT
Output Voltage
VIN = 12V, ILOAD = 100 mA
VOUT
Output Voltage
5
7V ≤ VIN ≤ 40V, 0.1A ≤ ILOAD ≤ 0.5A
Output Voltage
7V ≤ VIN ≤ 60V, 0.1A ≤ ILOAD ≤ 0.5A
Efficiency
VIN = 12V, ILOAD = 0.5A
77
3
5.100
V(Max)
4.800/4.750
V(Min)
5.200/5.250
V(Max)
V
5
LM2574HV
η
V(Min)
5
LM2574
VOUT
V
4.900
4.800/4.750
V(Min)
5.225/5.275
V(Max)
%
www.national.com
LM2574-12, LM2574HV-12
Electrical Characteristics
Specifications with standard type face are for TJ = 25˚C, and those with boldface type apply over full Operating Temperature Range.
Symbol
Parameter
Conditions
LM2574-12
LM2574HV-12
Typ
Units
(Limits)
Limit
(Note 2)
SYSTEM PARAMETERS (Note 3) Test Circuit Figure 2
VOUT
Output Voltage
VIN = 25V, ILOAD = 100 mA
VOUT
Output Voltage
12
15V ≤ VIN ≤ 40V, 0.1A ≤ ILOAD ≤ 0.5A
V
Output Voltage
15V ≤ VIN ≤ 60V, 0.1A ≤ ILOAD ≤ 0.5A
Efficiency
VIN = 15V, ILOAD = 0.5A
12.24
V(Max)
11.52/11.40
V(Min)
12.48/12.60
V(Max)
V
12
LM2574HV
η
V(Min)
12
LM2574
VOUT
11.76
11.52/11.40
V(Min)
12.54/12.66
V(Max)
%
88
LM2574-15, LM2574HV-15
Electrical Characteristics
Specifications with standard type face are for TJ = 25˚C, and those with boldface type apply over full Operating Temperature Range.
Symbol
Parameter
Conditions
LM2574-15
LM2574HV-15
Typ
Units
(Limits)
Limit
(Note 2)
SYSTEM PARAMETERS (Note 3) Test Circuit Figure 2
VOUT
Output Voltage
VIN = 30V, ILOAD = 100 mA
VOUT
Output Voltage
15
18V ≤ VIN ≤ 40V, 0.1A ≤ ILOAD ≤ 0.5A
V
Output Voltage
18V ≤ VIN ≤ 60V, 0.1A ≤ ILOAD ≤ 0.5A
Efficiency
VIN = 18V, ILOAD = 0.5A
15.30
V(Max)
14.40/14.25
V(Min)
15.60/15.75
V(Max)
V
15
LM2574HV
η
V(Min)
15
LM2574
VOUT
14.70
14.40/14.25
V(Min)
15.68/15.83
V(Max)
%
88
LM2574-ADJ, LM2574HV-ADJ
Electrical Characteristics
Specifications with standard type face are for TJ = 25˚C, and those with boldface type apply over full Operating Temperature Range. Unless otherwise specified, VIN = 12V, ILOAD = 100 mA.
Symbol
Parameter
Conditions
LM2574-ADJ
LM2574HV-ADJ
Typ
Units
(Limits)
Limit
(Note 2)
SYSTEM PARAMETERS (Note 3) Test Circuit Figure 2
VFB
Feedback Voltage
VIN = 12V, ILOAD = 100 mA
www.national.com
1.230
4
V
1.217
V(Min)
1.243
V(Max)
LM2574-ADJ, LM2574HV-ADJ
Electrical Characteristics (Continued)
Specifications with standard type face are for TJ = 25˚C, and those with boldface type apply over full Operating Temperature Range. Unless otherwise specified, VIN = 12V, ILOAD = 100 mA.
Symbol
Parameter
Conditions
LM2574-ADJ
LM2574HV-ADJ
Typ
Units
(Limits)
Limit
(Note 2)
SYSTEM PARAMETERS (Note 3) Test Circuit Figure 2
VFB
VFB
η
Feedback Voltage
7V ≤ VIN ≤ 40V, 0.1A ≤ ILOAD ≤ 0.5A
LM2574
VOUT Programmed for 5V. Circuit of Figure 2
Feedback Voltage
7V ≤ VIN ≤ 60V, 0.1A ≤ ILOAD ≤ 0.5A
LM2574HV
VOUT Programmed for 5V. Circuit of Figure 2
Efficiency
VIN = 12V, VOUT = 5V, ILOAD = 0.5A
1.230
V
1.193/1.180
V(Min)
1.267/1.280
V(Max)
1.230
1.193/1.180
V(Min)
1.273/1.286
V(Max)
%
77
All Output Voltage Versions
Electrical Characteristics
Specifications with standard type face are for TJ = 25˚C, and those with boldface type apply over full Operating Temperature Range. Unless otherwise specified, VIN = 12V for the 3.3V, 5V, and Adjustable version, VIN = 25V for the 12V version,
and VIN = 30V for the 15V version. ILOAD = 100 mA.
Symbol
Parameter
Conditions
LM2574-XX
LM2574HV-XX
Typ
Units
(Limits)
Limit
(Note 2)
DEVICE PARAMETERS
Ib
Feedback Bias
Current
Adjustable Version Only, VOUT = 5V
50
fO
Oscillator Frequency
(see Note 10)
52
VSAT
Saturation Voltage
IOUT = 0.5A (Note 4)
Max Duty Cycle
(ON)
(Note 5)
98
ICL
Current Limit
Peak Current, (Notes 4, 10)
1.0
Output Leakage
Output = 0V
Output = −1V
(Notes 6, 7)
Current
ISTBY
Quiescent Current
Standby Quiescent
(Note 6)
Thermal Resistance
kHz(Min)
58/63
kHz(Max)
1.2/1.4
V(max)
kHz
V
%
93
%(Min)
0.7/0.65
A(Min)
A
1.6/1.8
A(Max)
2
mA(Max)
30
mA(Max)
10
mA(Max)
200
µA(Max)
mA
5
ON /OFF Pin = 5V (OFF)
mA
50
Current
θJA
47/42
7.5
Output = −1V
IQ
nA
0.9
DC
IL
100/500
N Package, Junction to Ambient (Note 8)
92
θJA
N Package, Junction to Ambient (Note 9)
72
θJA
M Package, Junction to Ambient (Note 8)
102
θJA
M Package, Junction to Ambient (Note 9)
78
5
µA
˚C/W
www.national.com
All Output Voltage Versions
Electrical Characteristics (Continued)
Specifications with standard type face are for TJ = 25˚C, and those with boldface type apply over full Operating Temperature Range. Unless otherwise specified, VIN = 12V for the 3.3V, 5V, and Adjustable version, VIN = 25V for the 12V version,
and VIN = 30V for the 15V version. ILOAD = 100 mA.
Symbol
Parameter
Conditions
LM2574-XX
LM2574HV-XX
Typ
Units
(Limits)
Limit
(Note 2)
ON /OFF CONTROL Test Circuit Figure 2
VIH
ON /OFF Pin Logic
VIL
Input Level
IH
ON /OFF Pin Input
VOUT = 0V
VOUT = Nominal Output Voltage
ON /OFF Pin = 5V (OFF)
1.4
2.2/2.4
V(Min)
1.2
1.0/0.8
V(Max)
30
µA(Max)
10
µA(Max)
12
Current
ON /OFF Pin = 0V (ON)
IIL
µA
0
µA
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics.
Note 2: All limits guaranteed at room temperature (Standard type face) and at temperature extremes (bold type face). All room temperature limits are 100% production tested. All limits at temperature extremes are guaranteed via correlation using standard Statistical Quality Control (SQC) methods. All limits are used to calculate
Average Outgoing Quality Level.
Note 3: External components such as the catch diode, inductor, input and output capacitors can affect switching regulator system performance. When the LM2574
is used as shown in the Figure 2 test circuit, system performance will be as shown in system parameters section of Electrical Characteristics.
Note 4: Output pin sourcing current. No diode, inductor or capacitor connected to output pin.
Note 5: Feedback pin removed from output and connected to 0V.
Note 6: Feedback pin removed from output and connected to +12V for the Adjustable, 3.3V, and 5V versions, and +25V for the 12V and 15V versions, to force the
output transistor OFF.
Note 7: VIN = 40V (60V for high voltage version).
Note 8: Junction to ambient thermal resistance with approximately 1 square inch of printed circuit board copper surrounding the leads. Additional copper area will
lower thermal resistance further. See application hints in this data sheet and the thermal model in Switchers Made Simple software.
Note 9: Junction to ambient thermal resistance with approximately 4 square inches of 1 oz. (0.0014 in. thick) printed circuit board copper surrounding the leads. Additional copper area will lower thermal resistance further. (See Note 8.)
Note 10: The oscillator frequency reduces to approximately 18 kHz in the event of an output short or an overload which causes the regulated output voltage to drop
approximately 40% from the nominal output voltage. This self protection feature lowers the average power dissipation of the IC by lowering the minimum duty cycle
from 5% down to approximately 2%.
Typical Performance Characteristics
Normalized Output Voltage
(Circuit of Figure 2)
Line Regulation
Dropout Voltage
DS011394-27
www.national.com
DS011394-28
6
DS011394-29
Typical Performance Characteristics
(Circuit of Figure 2) (Continued)
Supply Current
Current Limit
Standby
Quiescent Current
DS011394-30
DS011394-31
DS011394-32
Oscillator Frequency
Switch Saturation
Voltage
Efficiency
DS011394-33
DS011394-35
DS011394-34
Minimum Operating Voltage
Supply Current
vs Duty Cycle
Feedback Voltage
vs Duty Cycle
DS011394-36
DS011394-37
7
DS011394-38
www.national.com
Typical Performance Characteristics
(Circuit of Figure 2) (Continued)
Feedback
Pin Current
Junction to Ambient
Thermal Resistance
DS011394-40
DS011394-39
Continuous Mode Switching Waveforms
VOUT = 5V, 500 mA Load Current, L = 330 µH
Discontinuous Mode Switching Waveforms
VOUT = 5V, 100 mA Load Current, L = 100 µH
DS011394-6
DS011394-7
Notes:
A: Output Pin Voltage, 10V/div
B: Inductor Current, 0.2 A/div
C: Output Ripple Voltage, 20 mV/div,
AC-Coupled
Horizontal Time Base: 5 µs/div
Notes:
A: Output Pin Voltage, 10V/div
B: Inductor Current, 0.2 A/div
C: Output Ripple Voltage, 20 mV/div,
AC-Coupled
Horizontal Time Base: 5 µs/div
500 mA Load Transient Response for Continuous
Mode Operation. L = 330 µH, COUT = 300 µF
250 mA Load Transient Response for Discontinuous
Mode Operation. L = 68 µH, COUT = 470 µF
DS011394-8
Notes:
A: Output Voltage, 50 mV/div.
AC Coupled
B: 100 mA to 500 mA Load Pulse
Horizontal Time Base: 200 µs/div
www.national.com
DS011394-9
Notes:
A: Output Voltage, 50 mV/div.
AC Coupled
B: 50 mA to 250 mA Load Pulse
Horizontal Time Base: 200 µs/div
8
Block Diagram
DS011394-10
R1 = 1k
3.3V, R2 = 1.7k
5V, R2 = 3.1k
12V, R2 = 8.84k
15V, R2 = 11.3k
For Adj. Version
R1 = Open, R2 = 0Ω
Note: Pin numbers are for the 8-pin DIP package.
FIGURE 1.
9
www.national.com
Test Circuit and Layout Guidelines
Fixed Output Voltage Versions
DS011394-11
CIN — 22 µF, 75V
Aluminum Electrolytic
COUT — 220 µF, 25V
Aluminum Electrolytic
D1 — Schottky, 11DQ06
L1 — 330 µH, 52627
(for 5V in, 3.3V out, use
100 µH, RL-1284-100)
R1 — 2k, 0.1%
R2 — 6.12k, 0.1%
Adjustable Output Voltage Version
DS011394-12
FIGURE 2.
As in any switching regulator, layout is very important. Rapidly switching currents associated with wiring inductance
generate voltage transients which can cause problems. For
minimal inductance and ground loops, the length of the leads
indicated by heavy lines should be kept as short as possible. Single-point grounding (as indicated) or ground plane
construction should be used for best results. When using the
Adjustable version, physically locate the programming resistors near the regulator, to keep the sensitive feedback wiring
short.
www.national.com
10
Test Circuit and Layout Guidelines
U.S. Source
(Continued)
Note 1: Pulse Engineering,
(619) 674-8100
P.O. Box 12236, San Diego, CA 92112
Inductor
Pulse Eng.
Renco
NPI
Value
(Note 1)
(Note 2)
(Note 3)
Note 2: Renco Electronics Inc.,
NP5915
60 Jeffryn Blvd. East, Deer Park, NY 11729
*Contact Manufacturer
68 µH
*
RL-1284-68-43
(516) 586-5566
100 µH
*
RL-1284-100-43
NP5916
150 µH
52625
RL-1284-150-43
NP5917
220 µH
52626
RL-1284-220-43
NP5918/5919
European Source
330 µH
52627
RL-1284-330-43
NP5920/5921
Note 3: NPI/APC
470 µH
52628
RL-1284-470-43
NP5922
47 Riverside, Medway City Estate
Strood, Rochester, Kent
680 µH
52629
RL-1283-680-43
NP5923
1000 µH
52631
RL-1283-1000-43
*
1500 µH
*
RL-1283-1500-43
*
2200 µH
*
RL-1283-2200-43
*
+44 (0) 634 290588
ME2 4DP.
UK
*Contact Manufacturer
FIGURE 3. Inductor Selection by
Manufacturer’s Part Number
11
www.national.com
LM2574 Series Buck Regulator Design Procedure
PROCEDURE (Fixed Output Voltage Versions)
EXAMPLE (Fixed Output Voltage Versions)
Given:
VOUT = Regulated Output Voltage (3.3V, 5V, 12V, or 15V)
VIN(Max) = Maximum Input Voltage
ILOAD(Max) = Maximum Load Current
Given:
VOUT = 5V
VIN(Max) = 15V
ILOAD(Max) = 0.4A
1. Inductor Selection (L1)
1. Inductor Selection (L1)
A. Use the selection guide shown in Figure 5.
B. From the selection guide, the inductance area intersected
by the 15V line and 0.4A line is 330.
C. Inductor value required is 330 µH. From the table in Figure
3, choose Pulse Engineering PE-52627, Renco RL-1284-330,
or NPI NP5920/5921.
A. Select the correct Inductor value selection guide from Figures 4, 5, 6, or Figure 7. (Output voltages of 3.3V, 5V, 12V or
15V respectively). For other output voltages, see the design
procedure for the adjustable version.
B. From the inductor value selection guide, identify the inductance region intersected by VIN(Max) and ILOAD(Max).
C. Select an appropriate inductor from the table shown in Figure 3. Part numbers are listed for three inductor manufacturers. The inductor chosen must be rated for operation at the
LM2574 switching frequency (52 kHz) and for a current rating
of 1.5 x ILOAD. For additional inductor information, see the inductor section in the Application Hints section of this data
sheet.
2. Output Capacitor Selection (COUT)
A. The value of the output capacitor together with the inductor
defines the dominate pole-pair of the switching regulator loop.
For stable operation and an acceptable output ripple voltage,
(approximately 1% of the output voltage) a value between
100 µF and 470 µF is recommended.
B. The capacitor’s voltage rating should be at least 1.5 times
greater than the output voltage. For a 5V regulator, a rating of
at least 8V is appropriate, and a 10V or 15V rating is recommended.
Higher voltage electrolytic capacitors generally have lower
ESR numbers, and for this reason it may be necessary to select a capacitor rated for a higher voltage than would normally
be needed.
2. Output Capacitor Selection (COUT)
A. COUT = 100 µF to 470 µF standard aluminum electrolytic.
B. Capacitor voltage rating = 20V.
3. Catch Diode Selection (D1)
A. The catch-diode current rating must be at least 1.5 times
greater than the maximum load current. Also, if the power
supply design must withstand a continuous output short, the
diode should have a current rating equal to the maximum current limit of the LM2574. The most stressful condition for this
diode is an overload or shorted output condition.
B. The reverse voltage rating of the diode should be at least
1.25 times the maximum input voltage.
3. Catch Diode Selection (D1)
A. For this example, a 1A current rating is adequate.
B. Use a 20V 1N5817 or SR102 Schottky diode, or any of the
suggested fast-recovery diodes shown in Figure 9.
4. Input Capacitor (CIN)
An aluminum or tantalum electrolytic bypass capacitor located
close to the regulator is needed for stable operation.
www.national.com
4. Input Capacitor (CIN)
A 22 µF aluminum electrolytic capacitor located near the input
and ground pins provides sufficient bypassing.
12
LM2574 Series Buck Regulator Design Procedure
(Continued)
INDUCTOR VALUE SELECTION GUIDES (For Continuous Mode Operation)
DS011394-26
FIGURE 4. LM2574HV-3.3 Inductor Selection Guide
DS011394-14
FIGURE 6. LM2574HV-12 Inductor Selection Guide
DS011394-13
FIGURE 5. LM2574HV-5.0 Inductor Selection Guide
DS011394-15
FIGURE 7. LM2574HV-15 Inductor Selection Guide
13
www.national.com
LM2574 Series Buck Regulator Design Procedure
(Continued)
DS011394-16
FIGURE 8. LM2574HV-ADJ Inductor Selection Guide
PROCEDURE (Adjustable Output Voltage Versions)
EXAMPLE (Adjustable Output Voltage Versions)
Given:
VOUT = Regulated Output Voltage
VIN(Max) = Maximum Input Voltage
ILOAD(Max) = Maximum Load Current
F = Switching Frequency (Fixed at 52 kHz)
Given:
VOUT = 24V
VIN(Max) = 40V
ILOAD(Max) = 0.4A
F = 52 kHz
1. Programming Output Voltage (Selecting R1 and R2, as
shown in Figure 2)
1. Programming Output Voltage (Selecting R1 and R2)
Use the following formula to select the appropriate resistor
values.
R2 = 1k (19.51−1) = 18.51k, closest 1% value is 18.7k
R1 can be between 1k and 5k. (For best temperature coefficient and stability with time, use 1% metal film resistors)
2. Inductor Selection (L1)
2. Inductor Selection (L1)
A. Calculate the inductor Volt • microsecond constant,
E • T (V • µs), from the following formula:
A. Calculate E • T (V • µs)
B. E • T = 185 V • µs
C. ILOAD(Max) = 0.4A
D. Inductance Region = 1000
E. Inductor Value = 1000 µH Choose from Pulse Engineering Part #PE-52631, or Renco Part #RL-1283-1000.
B. Use the E • T value from the previous formula and match
it with the E • T number on the vertical axis of the Inductor
Value Selection Guide shown in Figure 8.
C. On the horizontal axis, select the maximum load current.
D. Identify the inductance region intersected by the E • T
value and the maximum load current value, and note the inductor value for that region.
E. Select an appropriate inductor from the table shown in Figure 3. Part numbers are listed for three inductor manufacturers. The inductor chosen must be rated for operation at the
LM2574 switching frequency (52 kHz) and for a current rating
of 1.5 x ILOAD. For additional inductor information, see the inductor section in the application hints section of this data
sheet.
www.national.com
14
LM2574 Series Buck Regulator Design Procedure
PROCEDURE (Adjustable Output Voltage Versions)
(Continued)
EXAMPLE (Adjustable Output Voltage Versions)
3. Output Capacitor Selection (COUT)
3. Output Capacitor Selection (COUT)
A. The value of the output capacitor together with the inductor
defines the dominate pole-pair of the switching regulator loop.
For stable operation, the capacitor must satisfy the following
requirement:
However, for acceptable output ripple voltage select
COUT ≥ 100 µF
COUT = 100 µF electrolytic capacitor
The above formula yields capacitor values between 5 µF and
1000 µF that will satisfy the loop requirements for stable operation. But to achieve an acceptable output ripple voltage,
(approximately 1% of the output voltage) and transient response, the output capacitor may need to be several times
larger than the above formula yields.
B. The capacitor’s voltage rating should be at last 1.5 times
greater than the output voltage. For a 24V regulator, a rating
of at least 35V is recommended.
Higher voltage electrolytic capacitors generally have lower
ESR numbers, and for this reasion it may be necessary to select a capacitor rate for a higher voltage than would normally
be needed.
4. Catch Diode Selection (D1)
A. The catch-diode current rating must be at least 1.5 times
greater than the maximum load current. Also, if the power
supply design must withstand a continuous output short, the
diode should have a current rating equal to the maximum current limit of the LM2574. The most stressful condition for this
diode is an overload or shorted output condition. Suitable diodes are shown in the selection guide of Figure 9.
B. The reverse voltage rating of the diode should be at least
1.25 times the maximum input voltage.
4. Catch Diode Selection (D1)
A. For this example, a 1A current rating is adequate.
B. Use a 50V MBR150 or 11DQ05 Schottky diode, or any of
the suggested fast-recovery diodes in Figure 9.
5. Input Capacitor (CIN)
An aluminum or tantalum electrolytic bypass capacitor located
close to the regulator is needed for stable operation.
5. Input Capacitor (CIN)
A 22 µF aluminum electrolytic capacitor located near the input
and ground pins provides sufficient bypassing. See (Figure 9).
To further simplify the buck regulator design procedure, National Semiconductor is making available computer design
software to be used with the Simple Switcher line of switching
regulators. Switchers Made Simple (version 3.3) is available
on a (31⁄2") diskette for IBM compatible computers from a National Semiconductor sales office in your area.
15
www.national.com
LM2574 Series Buck Regulator Design Procedure
VR
1 Amp Diodes
Schottky
20V
(Continued)
Fast Recovery
1N5817
SR102
MBR120P
30V
1N5818
SR103
40V
11DQ03
The
MBR130P
following
10JQ030
diodes
1N5819
are all
SR104
rated to
11DQ04
100V
11JQ04
MBR140P
50V
60V
MBR150
11DF1
SR105
10JF1
11DQ05
MUR110
11JQ05
HER102
MBR160
SR106
11DQ06
11JQ06
90V
11DQ09
FIGURE 9. Diode Selection Guide
INDUCTOR SELECTION
All switching regulators have two basic modes of operation:
continuous and discontinuous. The difference between the
two types relates to the inductor current, whether it is flowing
continuously, or if it drops to zero for a period of time in the
normal switching cycle. Each mode has distinctively different
operating characteristics, which can affect the regulator performance and requirements.
The LM2574 (or any of the Simple Switcher family) can be
used for both continuous and discontinuous modes of operation.
Application Hints
INPUT CAPACITOR (CIN)
To maintain stability, the regulator input pin must be bypassed with at least a 22 µF electrolytic capacitor. The capacitor’s leads must be kept short, and located near the
regulator.
If the operating temperature range includes temperatures
below −25˚C, the input capacitor value may need to be
larger. With most electrolytic capacitors, the capacitance
value decreases and the ESR increases with lower temperatures and age. Paralleling a ceramic or solid tantalum capacitor will increase the regulator stability at cold temperatures. For maximum capacitor operating lifetime, the
capacitor’s RMS ripple current rating should be greater than
In many cases the preferred mode of operation is in the continuous mode. It offers better load regulation, lower peak
switch, inductor and diode currents, and can have lower output ripple voltage. But it does require relatively large inductor
values to keep the inductor current flowing continuously, especially at low output load currents.
To simplify the inductor selection process, an inductor selection guide (nomograph) was designed (see Figure 4 through
Figure 8). This guide assumes continuous mode operation,
and selects an inductor that will allow a peak-to-peak inductor ripple current (∆IIND) to be a certain percentage of the
maximum design load current. In the LM2574 SIMPLE
SWITCHER, the peak-to-peak inductor ripple current percentage (of load current) is allowed to change as different
design load currents are selected. By allowing the percentage of inductor ripple current to increase for lower current
applications, the inductor size and value can be kept relatively low.
www.national.com
16
Application Hints
the output ripple voltage can be calculated, or conversely,
measuring the output ripple voltage and knowing the ∆IIND,
the ESR can be calculated.
(Continued)
INDUCTOR RIPPLE CURRENT
When the switcher is operating in the continuous mode, the
inductor current waveform ranges from a triangular to a sawtooth type of waveform (depending on the input voltage). For
a given input voltage and output voltage, the peak-to-peak
amplitude of this inductor current waveform remains constant. As the load current rises or falls, the entire sawtooth
current waveform also rises or falls. The average DC value
of this waveform is equal to the DC load current (in the buck
regulator configuration).
From the previous example, the Peak-to-peak Inductor
Ripple Current (∆IIND) = 212 mA p-p. Once the ∆IND value is
known, the following three formulas can be used to calculate
additional information about the switching regulator circuit:
1.
Peak Inductor or peak switch current
If the load current drops to a low enough level, the bottom of
the sawtooth current waveform will reach zero, and the
switcher will change to a discontinuous mode of operation.
This is a perfectly acceptable mode of operation. Any buck
switching regulator (no matter how large the inductor value
is) will be forced to run discontinuous if the load current is
light enough.
The curve shown in Figure 10 illustrates how the peak-topeak inductor ripple current (∆IIND) is allowed to change as
different maximum load currents are selected, and also how
it changes as the operating point varies from the upper border to the lower border within an inductance region (see Inductor Selection guides).
2.
Minimum load current before the circuit becomes discontinuous
3. Output Ripple Voltage = (∆IIND) x (ESR of COUT)
The selection guide chooses inductor values suitable for
continuous mode operation, but if the inductor value chosen
is prohibitively high, the designer should investigate the possibility of discontinuous operation. The computer design software Switchers Made Simple will provide all component
values for discontinuous (as well as continuous) mode of operation.
Inductors are available in different styles such as pot core,
toroid, E-frame, bobbin core, etc., as well as different core
materials, such as ferrites and powdered iron. The least expensive, the bobbin core type, consists of wire wrapped on a
ferrite rod core. This type of construction makes for an inexpensive inductor, but since the magnetic flux is not completely contained within the core, it generates more electromagnetic interference (EMI). This EMl can cause problems
in sensitive circuits, or can give incorrect scope readings because of induced voltages in the scope probe.
The inductors listed in the selection chart include powdered
iron toroid for Pulse Engineering, and ferrite bobbin core for
Renco.
An inductor should not be operated beyond its maximum
rated current because it may saturate. When an inductor begins to saturate, the inductance decreases rapidly and the
inductor begins to look mainly resistive (the DC resistance of
the winding). This can cause the inductor current to rise very
rapidly and will affect the energy storage capabilities of the
inductor and could cause inductor overheating. Different inductor types have different saturation characteristics, and
this should be kept in mind when selecting an inductor. The
inductor manufacturers’ data sheets include current and energy limits to avoid inductor saturation.
DS011394-18
FIGURE 10. Inductor Ripple Current (∆IIND) Range
Based on Selection Guides from Figure 4 through
Figure 8.
Consider the following example:
VOUT = 5V @ 0.4A
VIN = 10V minimum up to 20V maximum
The selection guide in Figure 5 shows that for a 0.4A load
current, and an input voltage range between 10V and 20V,
the inductance region selected by the guide is 330 µH. This
value of inductance will allow a peak-to-peak inductor ripple
current (∆IIND) to flow that will be a percentage of the maximum load current. For this inductor value, the ∆IIND will also
vary depending on the input voltage. As the input voltage increases to 20V, it approaches the upper border of the inductance region, and the inductor ripple current increases. Referring to the curve in Figure 10, it can be seen that at the
0.4A load current level, and operating near the upper border
of the 330 µH inductance region, the ∆IIND will be 53% of
0.4A, or 212 mA p-p.
This ∆IIND is important because from this number the peak
inductor current rating can be determined, the minimum load
current required before the circuit goes to discontinuous operation, and also, knowing the ESR of the output capacitor,
OUTPUT CAPACITOR
An output capacitor is required to filter the output voltage and
is needed for loop stability. The capacitor should be located
near the LM2574 using short pc board traces. Standard aluminum electrolytics are usually adequate, but low ESR types
are recommended for low output ripple voltage and good
stability. The ESR of a capacitor depends on many factors,
some which are: the value, the voltage rating, physical size
and the type of construction. In general, low value or low
voltage (less than 12V) electrolytic capacitors usually have
higher ESR numbers.
The amount of output ripple voltage is primarily a function of
the ESR (Equivalent Series Resistance) of the output ca-
17
www.national.com
Application Hints
FEEDBACK CONNECTION
The LM2574 (fixed voltage versions) feedback pin must be
wired to the output voltage point of the switching power supply. When using the adjustable version, physically locate
both output voltage programming resistors near the LM2574
to avoid picking up unwanted noise. Avoid using resistors
greater than 100 kΩ because of the increased chance of
noise pickup.
(Continued)
pacitor and the amplitude of the inductor ripple current
(∆IIND). See the section on inductor ripple current in Application Hints.
The lower capacitor values (100 µF- 330 µF) will allow typically 50 mV to 150 mV of output ripple voltage, while largervalue capacitors will reduce the ripple to approximately
20 mV to 50 mV.
Output Ripple Voltage = (∆IIND) (ESR of COUT)
ON /OFF INPUT
For normal operation, the ON /OFF pin should be grounded
or driven with a low-level TTL voltage (typically below 1.6V).
To put the regulator into standby mode, drive this pin with a
high-level TTL or CMOS signal. The ON /OFF pin can be
safely pulled up to +VIN without a resistor in series with it.
The ON /OFF pin should not be left open.
To further reduce the output ripple voltage, several standard
electrolytic capacitors may be paralleled, or a higher-grade
capacitor may be used. Such capacitors are often called
“high-frequency,” “low-inductance,” or “low-ESR.” These will
reduce the output ripple to 10 mV or 20 mV. However, when
operating in the continuous mode, reducing the ESR below
0.03Ω can cause instability in the regulator.
GROUNDING
The 8-pin molded DIP and the 14-pin surface mount package have separate power and signal ground pins. Both
ground pins should be soldered directly to wide printed circuit board copper traces to assure low inductance connections and good thermal properties.
Tantalum capacitors can have a very low ESR, and should
be carefully evaluated if it is the only output capacitor. Because of their good low temperature characteristics, a tantalum can be used in parallel with aluminum electrolytics, with
the tantalum making up 10% or 20% of the total capacitance.
The capacitor’s ripple current rating at 52 kHz should be at
least 50% higher than the peak-to-peak inductor ripple current.
THERMAL CONSIDERATIONS
The 8-pin DIP (N) package and the 14-pin Surface Mount
(M) package are molded plastic packages with solid copper
lead frames. The copper lead frame conducts the majority of
the heat from the die, through the leads, to the printed circuit
board copper, which acts as the heat sink. For best thermal
performance, wide copper traces should be used, and all
ground and unused pins should be soldered to generous
amounts of printed circuit board copper, such as a ground
plane. Large areas of copper provide the best transfer of
heat (lower thermal resistance) to the surrounding air, and
even double-sided or multilayer boards provide better heat
paths to the surrounding air. Unless the power levels are
small, using a socket for the 8-pin package is not recommended because of the additional thermal resistance it introduces, and the resultant higher junction temperature.
Because of the 0.5A current rating of the LM2574, the total
package power dissipation for this switcher is quite low,
ranging from approximately 0.1W up to 0.75W under varying
conditions. In a carefully engineered printed circuit board,
both the N and the M package can easily dissipate up to
0.75W, even at ambient temperatures of 60˚C, and still keep
the maximum junction temperature below 125˚C.
A curve displaying thermal resistance vs. pc board area for
the two packages is shown in the Typical Performance Characteristics curves section of this data sheet.
These thermal resistance numbers are approximate, and
there can be many factors that will affect the final thermal resistance. Some of these factors include board size, shape,
thickness, position, location, and board temperature. Other
factors are, the area of printed circuit copper, copper thickness, trace width, multi-layer, single- or double-sided, and
the amount of solder on the board. The effectiveness of the
pc board to dissipate heat also depends on the size, number
and spacing of other components on the board. Furthermore, some of these components, such as the catch diode
and inductor will generate some additional heat. Also, the
thermal resistance decreases as the power level increases
because of the increased air current activity at the higher
power levels, and the lower surface to air resistance coefficient at higher temperatures.
CATCH DIODE
Buck regulators require a diode to provide a return path for
the inductor current when the switch is off. This diode should
be located close to the LM2574 using short leads and short
printed circuit traces.
Because of their fast switching speed and low forward voltage drop, Schottky diodes provide the best efficiency, especially in low output voltage switching regulators (less than
5V). Fast-Recovery, High-Efficiency, or Ultra-Fast Recovery
diodes are also suitable, but some types with an abrupt turnoff characteristic may cause instability and EMI problems. A
fast-recovery diode with soft recovery characteristics is a
better choice. Standard 60 Hz diodes (e.g., 1N4001 or
1N5400, etc.) are also not suitable. See Figure 9 for Schottky and “soft” fast-recovery diode selection guide.
OUTPUT VOLTAGE RIPPLE AND TRANSIENTS
The output voltage of a switching power supply will contain a
sawtooth ripple voltage at the switcher frequency, typically
about 1% of the output voltage, and may also contain short
voltage spikes at the peaks of the sawtooth waveform.
The output ripple voltage is due mainly to the inductor sawtooth ripple current multiplied by the ESR of the output capacitor. (See the inductor selection in the application hints.)
The voltage spikes are present because of the the fast
switching action of the output switch, and the parasitic inductance of the output filter capacitor. To minimize these voltage
spikes, special low inductance capacitors can be used, and
their lead lengths must be kept short. Wiring inductance,
stray capacitance, as well as the scope probe used to evaluate these transients, all contribute to the amplitude of these
spikes.
An additional small LC filter (20 µH & 100 µF) can be added
to the output (as shown in Figure 16 ) to further reduce the
amount of output ripple and transients. A 10 x reduction in
output ripple voltage and transients is possible with this filter.
www.national.com
18
Application Hints
The power dissipation (PD) for the IC could be measured, or
it can be estimated by using the formula:
(Continued)
The data sheet thermal resistance curves and the thermal
model in Switchers Made Simple software (version 3.3)
can estimate the maximum junction temperature based on
operating conditions. ln addition, the junction temperature
can be estimated in actual circuit operation by using the following equation.
Tj = Tcu + (θj-cu x PD)
Where IS is obtained from the typical supply current curve
(adjustable version use the supply current vs. duty cycle
curve).
With the switcher operating under worst case conditions and
all other components on the board in the intended enclosure,
measure the copper temperature (Tcu ) near the IC. This can
be done by temporarily soldering a small thermocouple to
the pc board copper near the IC, or by holding a small thermocouple on the pc board copper using thermal grease for
good thermal conduction.
The thermal resistance (θj-cu) for the two packages is:
θj-cu = 42˚C/W for the N-8 package
θj-cu = 52˚C/W for the M-14 package
Additional Applications
INVERTING REGULATOR
Figure 11 shows a LM2574-12 in a buck-boost configuration
to generate a negative 12V output from a positive input voltage. This circuit bootstraps the regulator’s ground pin to the
negative output voltage, then by grounding the feedback pin,
the regulator senses the inverted output voltage and regulates it to −12V.
DS011394-19
Note: Pin numbers are for the 8-pin DIP package.
FIGURE 11. Inverting Buck-Boost Develops −12V
Where fosc = 52 kHz. Under normal continuous inductor current operating conditions, the minimum VIN represents the
worst case. Select an inductor that is rated for the peak current anticipated.
Also, the maximum voltage appearing across the regulator is
the absolute sum of the input and output voltage. For a −12V
output, the maximum input voltage for the LM2574 is +28V,
or +48V for the LM2574HV.
The Switchers Made Simple version 3.3) design software
can be used to determine the feasibility of regulator designs
using different topologies, different input-output parameters,
different components, etc.
For an input voltage of 8V or more, the maximum available
output current in this configuration is approximately 100 mA.
At lighter loads, the minimum input voltage required drops to
approximately 4.7V.
The switch currents in this buck-boost configuration are
higher than in the standard buck-mode design, thus lowering
the available output current. Also, the start-up input current
of the buck-boost converter is higher than the standard buckmode regulator, and this may overload an input power
source with a current limit less than 0.6A. Using a delayed
turn-on or an undervoltage lockout circuit (described in the
next section) would allow the input voltage to rise to a high
enough level before the switcher would be allowed to turn
on.
NEGATIVE BOOST REGULATOR
Another variation on the buck-boost topology is the negative
boost configuration. The circuit in Figure 12 accepts an input
voltage ranging from −5V to −12V and provides a regulated
−12V output. Input voltages greater than −12V will cause the
output to rise above −12V, but will not damage the regulator.
Because of the structural differences between the buck and
the buck-boost regulator topologies, the buck regulator design procedure section can not be used to to select the inductor or the output capacitor. The recommended range of
inductor values for the buck-boost design is between 68 µH
and 220 µH, and the output capacitor values must be larger
than what is normally required for buck designs. Low input
voltages or high output currents require a large value output
capacitor (in the thousands of micro Farads).
The peak inductor current, which is the same as the peak
switch current, can be calculated from the following formula:
19
www.national.com
Additional Applications
(Continued)
DS011394-21
Note: Complete circuit not shown.
Note: Pin numbers are for 8-pin DIP package.
DS011394-20
Note: Pin numbers are for 8-pin DIP package.
FIGURE 13. Undervoltage Lockout for Buck Circuit
FIGURE 12. Negative Boost
Because of the boosting function of this type of regulator, the
switch current is relatively high, especially at low input voltages. Output load current limitations are a result of the maximum current rating of the switch. Also, boost regulators can
not provide current limiting load protection in the event of a
shorted load, so some other means (such as a fuse) may be
necessary.
UNDERVOLTAGE LOCKOUT
In some applications it is desirable to keep the regulator off
until the input voltage reaches a certain threshold. An undervoltage lockout circuit which accomplishes this task is shown
in Figure 13 while Figure 14 shows the same circuit applied
to a buck-boost configuration. These circuits keep the regulator off until the input voltage reaches a predetermined
level.
VTH ≈ VZ1 + 2VBE (Q1)
DS011394-22
Note: Complete circuit not shown (see Figure 11 ).
Note: Pin numbers are for 8-pin DIP package.
FIGURE 14. Undervoltage Lockout
for Buck-Boost Circuit
DELAYED STARTUP
The ON /OFF pin can be used to provide a delayed startup
feature as shown in Figure 15. With an input voltage of 20V
and for the part values shown, the circuit provides approximately 10 ms of delay time before the circuit begins switching. Increasing the RC time constant can provide longer delay times. But excessively large RC time constants can
cause problems with input voltages that are high in 60 Hz or
120 Hz ripple, by coupling the ripple into the ON /OFF pin.
ADJUSTABLE OUTPUT, LOW-RIPPLE POWER SUPPLY
A 500 mA power supply that features an adjustable output
voltage is shown in Figure 16. An additional L-C filter that reduces the output ripple by a factor of 10 or more is included
in this circuit.
DS011394-23
Note: Complete circuit not shown.
Note: Pin numbers are for 8-pin DIP package.
FIGURE 15. Delayed Startup
www.national.com
20
Additional Applications
(Continued)
DS011394-24
Note: Pin numbers are for 8-pin DIP package.
FIGURE 16. 1.2V to 55V Adjustable 500 mA Power Supply with Low Output Ripple
grade capacitors (“low-ESR”, “high-frequency”, or “lowinductance”) in the 100 µF–1000 µF range generally have
ESR of less than 0.15Ω.
Definition of Terms
BUCK REGULATOR
A switching regulator topology in which a higher voltage is
converted to a lower voltage. Also known as a step-down
switching regulator.
EQUIVALENT SERIES INDUCTANCE (ESL)
The pure inductance component of a capacitor (see Figure
17). The amount of inductance is determined to a large extent on the capacitor’s construction. In a buck regulator, this
unwanted inductance causes voltage spikes to appear on
the output.
BUCK-BOOST REGULATOR
A switching regulator topology in which a positive voltage is
converted to a negative voltage without a transformer.
OUTPUT RIPPLE VOLTAGE
The AC component of the switching regulator’s output voltage. It is usually dominated by the output capacitor’s ESR
multiplied by the inductor’s ripple current (∆IIND). The peakto-peak value of this sawtooth ripple current can be determined by reading the Inductor Ripple Current section of the
Application hints.
DUTY CYCLE (D)
Ratio of the output switch’s on-time to the oscillator period.
CAPACITOR RIPPLE CURRENT
RMS value of the maximum allowable alternating current at
which a capacitor can be operated continuously at a specified temperature.
CATCH DIODE OR CURRENT STEERING DIODE
The diode which provides a return path for the load current
when the LM2574 switch is OFF.
EFFICIENCY (η)
The proportion of input power actually delivered to the load.
STANDBY QUIESCENT CURRENT (ISTBY)
Supply current required by the LM2574 when in the standby
mode (ON/OFF pin is driven to TTL-high voltage, thus turning the output switch OFF).
INDUCTOR RIPPLE CURRENT (∆IIND)
The peak-to-peak value of the inductor current waveform,
typically a sawtooth waveform when the regulator is operating in the continuous mode (vs. discontinuous mode).
CAPACITOR EQUIVALENT SERIES RESISTANCE (ESR)
The purely resistive component of a real capacitor’s impedance (see Figure 17). It causes power loss resulting in capacitor heating, which directly affects the capacitor’s operating lifetime. When used as a switching regulator output filter,
higher ESR values result in higher output ripple voltages.
CONTINUOUS/DISCONTINUOUS MODE OPERATION
Relates to the inductor current. In the continuous mode, the
inductor current is always flowing and never drops to zero,
vs. the discontinuous mode, where the inductor current
drops to zero for a period of time in the normal switching
cycle.
DS011394-25
FIGURE 17. Simple Model of a Real Capacitor
Most standard aluminum electrolytic capacitors in the
100 µF–1000 µF range have 0.5Ω to 0.1Ω ESR. Higher-
21
www.national.com
Definition of Terms
OPERATING VOLT MICROSECOND CONSTANT (E • Top)
The product (in VoIt • µs) of the voltage applied to the inductor
and the time the voltage is applied. This E • Top constant is a
measure of the energy handling capability of an inductor and
is dependent upon the type of core, the core area, the number of turns, and the duty cycle.
(Continued)
INDUCTOR SATURATION
The condition which exists when an inductor cannot hold any
more magnetic flux. When an inductor saturates, the inductor appears less inductive and the resistive component dominates. Inductor current is then limited only by the DC resistance of the wire and the available source current.
www.national.com
22
Physical Dimensions
inches (millimeters) unless otherwise noted
14-Lead Wide Surface Mount (WM)
Order Number LM2574M-3.3, LM2574HVM-3.3, LM2574M-5.0,
LM2574HVM-5.0, LM2574M-12, LM2574HVM-12, LM2574M-15,
LM2574HVM-15, LM2574M-ADJ or LM2574HVM-ADJ
NS Package Number M14B
23
www.national.com
LM2574/LM2574HV SIMPLE SWITCHER 0.5A Step-Down Voltage Regulator
Physical Dimensions
inches (millimeters) unless otherwise noted (Continued)
8-Lead DIP (N)
Order Number LM2574M-3.3, LM2574HVM-3.3, LM2574HVN-5.0, LM2574HVN-12,
LM2574HVN-15, LM2574HVN-ADJ, LM2574N-5.0,
LM2574N-12, LM2574N-15 or LM2574N-ADJ
NS Package Number N08A
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and
whose failure to perform when properly used in
accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a
significant injury to the user.
National Semiconductor
Corporation
Americas
Tel: 1-800-272-9959
Fax: 1-800-737-7018
Email: [email protected]
www.national.com
National Semiconductor
Europe
Fax: +49 (0) 1 80-530 85 86
Email: [email protected]
Deutsch Tel: +49 (0) 1 80-530 85 85
English Tel: +49 (0) 1 80-532 78 32
Français Tel: +49 (0) 1 80-532 93 58
Italiano Tel: +49 (0) 1 80-534 16 80
2. A critical component is any component of a life
support device or system whose failure to perform
can be reasonably expected to cause the failure of
the life support device or system, or to affect its
safety or effectiveness.
National Semiconductor
Asia Pacific Customer
Response Group
Tel: 65-2544466
Fax: 65-2504466
Email: [email protected]
National Semiconductor
Japan Ltd.
Tel: 81-3-5639-7560
Fax: 81-3-5639-7507
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
Similar pages