NPC CF5015AL5 2.5v operation fundamental frequency crystal oscillator module ic Datasheet

CF5015 series
2.5V Operation Fundamental Frequency
Crystal Oscillator Module ICs
OVERVIEW
The CF5015 series are 2.5V operation crystal oscillator ICs. They are available for frequencies up to 60MHz.
The product lineup consists of AL× series for 2.5V exclusive use and BL× series compliant with 2.5V to 5V.
The built-in oscillator capacitor of AL× series is large, so that AL× series contribute to improve the frequency
stability. For the BL× series, the current consumption and drive level reduced so that they can realize the characteristics easier to design small-sized crystal oscillators. The oscillator circuit of each version is simply constructed, so that it can realize the crystal oscillator with excellent phase noise characteristics. Even if the valued
characteristics differ due to the application or the purpose, the selecting from these series for different purposes
allows the optimization.
FEATURES
■
■
■
■
■
Operating supply voltage range
• CF5015AL×: 2.25 to 2.75V
• CF5015BL×: 2.25 to 5.5V
Up to 60MHz oscillation frequency range
– 40 to 85°C operating temperature range
Oscillation capacitors built-in
• CF5015AL×: CG = 18pF, CD = 18pF
• CF5015BL×: CG = 4pF, CD = 8pF
Inverter amplifier feedback resistor built-in
■
■
■
■
■
■
Standby function
• High impedance in standby mode, oscillator stops
Low standby current
• Power-saving pull-up resistor built-in
fO, fO/2, fO/4, fO/8, or fO/16 output frequency,
determined by internal connection
CMOS output duty level (1/2VDD)
Molybdenum-gate CMOS process
Chip form (CF5015×L×)
SERIES CONFIGURATION
Version
Operating
supply
voltage
range [V]
Recommended oscillation frequency range*1 [MHz]
2.5V operation
3V operation
CL = 15pF CL = 30pF CL = 15pF CL = 30pF
Standby mode
Built-in
5V
Output
capacitance [pF]
Oscillator Output
operation
frequency
stop
state
function
C = 30pF
C
C
L
G
D
fO*2
CF5015AL1
fO/2
CF5015AL2
CF5015AL3 2.25 to 2.75
4 to 60
4 to 50
–
–
–
18
18
fO/4
CF5015AL4
fO/8
CF5015AL5
fO/16
CF5015BL1
fO*2
CF5015BL2
CF5015BL3
Yes
Hi-Z
Yes
Hi-Z
fO/2
2.25 to 3.6
4.5 to 5.5
12 to 60
12 to 50
12 to 60
12 to 50
12 to 60
4
8
fO/4
CF5015BL4
fO/8
CF5015BL5
fO/16
*1. The recommended oscillation frequency is a yardstick value derived from the crystal used for NPC characteristics authentication. However, the oscillator frequency band is not guaranteed. Specifically, the characteristics can vary greatly due to crystal characteristics and mounting conditions, so the
oscillation characteristics of components must be carefully evaluated.
*2. Oscillation frequency
ORDERING INFORMATION
Device
Package
CF5015×L×–2
Chip form
SEIKO NPC CORPORATION —1
CF5015 series
PAD LAYOUT
(Unit: µm)
(720,680)
Y
HA
5015
Q
NPC
VDD
VSS
INHN
(0,0)
XT
XTN
X
Chip size: 0.72 × 0.68mm
Chip thickness: 220 ± 30µm
PAD size: 90µm
Chip base: VDD level
PIN DESCRIPTION and PAD DIMENSIONS
Pad dimensions [µm]
Name
I/O
Description
X
Y
INHN
I
Output state control input. High impedance when LOW (oscillator stops).
Power-saving pull-up resistor built-in.
151
277
XT
I
Amplifier input
238
131
XTN
O
Amplifier output
512
131
VSS
–
Ground
588
345
Q
O
Output. Output frequency (fO, fO/2, fO/4, fO/8, fO/16) determined by internal connection
588
548
VDD
–
Supply voltage
131
548
Crystal connection pins.
Crystal is connected between XT and XTN.
BLOCK DIAGRAM
VDD VSS
XTN
CG
XT
CD
Rf
1/2
1/2
1/2
1/2
Q
INHN
INHN = LOW active
SEIKO NPC CORPORATION —2
CF5015 series
SPECIFICATIONS
Absolute Maximum Ratings
VSS = 0V
Parameter
Symbol
Supply voltage range
Condition
Rating
Unit
VDD
−0.5 to +7.0
V
VIN
−0.5 to VDD + 0.5
V
Output voltage range
VOUT
−0.5 to VDD + 0.5
V
Operating temperature range
Topr
−40 to +85
°C
Storage temperature range
TSTG
−65 to +150
°C
Output current
IOUT
12
mA
Rating
Unit
Input voltage range
Recommended Operating Conditions
2.5V operation (CF5015AL×/CF5015BL×)
VSS = 0V
Parameter
Symbol
Condition
Supply voltage range
VDD
2.25 to 2.75
V
Input voltage range
VIN
VSS to VDD
V
TOPR
−40 to +85
°C
4 to 60
MHz
Operating temperature range
Oscillation frequency range
fO
CF5015AL×
CF5015BL×
12 to 60
MHz
CL ≤ 15pF
0.25 to 60
MHz
CL ≤ 30pF
0.25 to 50
MHz
CL ≤ 15pF
0.75 to 60
MHz
CL ≤ 30pF
0.75 to 50
MHz
Rating
Unit
VDD
2.7 to 3.6
V
CF5015AL×
Output frequency range
fOUT
CF5015BL×
3V operation (CF5015BL×)
VSS = 0V
Parameter
Symbol
Supply voltage range
Input voltage range
Operating temperature range
Oscillation frequency range
Output frequency range
Condition
VIN
VSS to VDD
V
TOPR
−40 to +85
°C
fO
12 to 60
MHz
CL ≤ 15pF
0.75 to 60
MHz
CL ≤ 30pF
0.75 to 50
MHz
Rating
Unit
VDD
4.5 to 5.5
V
fOUT
5V operation (CF5015BL×)
VSS = 0V
Parameter
Supply voltage range
Input voltage range
Operating temperature range
Oscillation frequency range
Output frequency range
Symbol
Condition
VIN
VSS to VDD
V
TOPR
−40 to +85
°C
fO
12 to 60
MHz
0.75 to 60
MHz
fOUT
CL ≤ 30pF
SEIKO NPC CORPORATION —3
CF5015 series
Electrical Characteristics
2.5V operation (CF5015AL×/CF5015BL×)
VDD = 2.25 to 2.75V, VSS = 0V, Ta = −40 to +85°C unless otherwise noted.
Rating
Parameter
Symbol
Condition
Unit
min
typ
max
HIGH-level output voltage
VOH
Q: Measurement cct 1, VDD = 2.25V, IOH = 4mA
1.65
1.95
–
V
LOW-level output voltage
VOL
Q: Measurement cct 1, VDD = 2.25V, IOL = 4mA
–
0.3
0.4
V
HIGH-level input voltage
VIH
INHN
0.7VDD
–
–
V
LOW-level input voltage
VIL
INHN
–
–
0.3VDD
V
–
10
µA
IZ
Q: Measurement cct 2, INHN = LOW
VOH = VDD
–
Output leakage current
VOL = VSS
–
–
10
µA
CF5015AL1
–
5.5
11
mA
CF5015AL2
–
4
8
mA
CF5015AL3
–
3
6
mA
CF5015AL4
–
2.5
5
mA
CF5015AL5
–
2
4
mA
CF5015BL1
–
4.5
9
mA
CF5015BL2
–
3
6
mA
CF5015BL3
–
2
4
mA
CF5015BL4
–
1.5
3
mA
CF5015BL5
–
1
2
mA
–
–
3
µA
2
6
12
MΩ
20
100
200
kΩ
100
300
600
kΩ
CF5015AL×
15.3
18
20.7
pF
CF5015BL×
3.4
4
4.6
pF
CF5015AL×
15.3
18
20.7
pF
CF5015BL×
6.8
8
9.2
pF
Current consumption
Standby current
INHN pull-up resistance
IDD
IST
RUP1
Measurement cct 3, load cct 1,
INHN = open, CL = 15pF, f = 60MHz
Measurement cct 3, INHN = LOW
Measurement cct 4
RUP2
Feedback resistance
Rf
Measurement cct 5
CG
Design value. A monitor pattern on a
wafer is tested.
CD
Design value. A monitor pattern on a
wafer is tested.
Built-in capacitance
SEIKO NPC CORPORATION —4
CF5015 series
3V operation (CF5015BL×)
VDD = 2.7 to 3.6V, VSS = 0V, Ta = −40 to +85°C unless otherwise noted.
Rating
Parameter
Symbol
Condition
Unit
min
typ
max
HIGH-level output voltage
VOH
Q: Measurement cct 1, VDD = 2.7V, IOH = 4mA
2.1
2.4
–
V
LOW-level output voltage
VOL
Q: Measurement cct 1, VDD = 2.7V, IOL = 4mA
–
0.3
0.4
V
HIGH-level input voltage
VIH
INHN
0.7VDD
–
–
V
LOW-level input voltage
VIL
INHN
–
–
0.3VDD
V
–
10
µA
IZ
Q: Measurement cct 2, INHN = LOW
VOH = VDD
–
Output leakage current
VOL = VSS
–
–
10
µA
CF5015BL1
–
5.5
11
mA
CF5015BL2
–
3
6
mA
CF5015BL3
–
2
4
mA
CF5015BL4
–
1.5
3
mA
CF5015BL5
–
1
2
mA
–
–
5
µA
1
4
10
MΩ
20
100
200
kΩ
100
300
600
kΩ
3.4
4
4.6
pF
6.8
8
9.2
pF
Current consumption
Standby current
INHN pull-up resistance
IDD
IST
RUP1
Measurement cct 3, load cct 1,
INHN = open, CL = 15pF, f = 60MHz
Measurement cct 3, INHN = LOW
Measurement cct 4
RUP2
Feedback resistance
Built-in capacitance
Rf
CG
Measurement cct 5
Design value. A monitor pattern on a wafer is tested.
CD
5V operation (CF5015BL×)
VDD = 4.5 to 5.5V, VSS = 0V, Ta = −40 to +85°C unless otherwise noted.
Rating
Parameter
Symbol
Condition
Unit
min
typ
max
HIGH-level output voltage
VOH
Q: Measurement cct 1, VDD = 4.5V, IOH = 8mA
3.9
4.2
–
V
LOW-level output voltage
VOL
Q: Measurement cct 1, VDD = 4.5V, IOL = 8mA
–
0.3
0.4
V
HIGH-level input voltage
VIH
INHN
0.7VDD
–
–
V
LOW-level input voltage
VIL
INHN
–
–
0.3VDD
V
–
10
µA
IZ
Q: Measurement cct 2, INHN = LOW
VOH = VDD
–
Output leakage current
VOL = VSS
–
–
10
µA
CF5015BL1
–
15
30
mA
CF5015BL2
–
9.5
19
mA
CF5015BL3
–
6.5
13
mA
CF5015BL4
–
5
10
mA
CF5015BL5
–
4
8
mA
–
–
10
µA
0.5
2
8
MΩ
10
50
150
kΩ
100
300
600
kΩ
3.4
4
4.6
pF
6.8
8
9.2
pF
Current consumption
Standby current
INHN pull-up resistance
IDD
IST
RUP1
Measurement cct 3, load cct 1,
INHN = open, CL = 30pF, f = 60MHz
Measurement cct 3, INHN = LOW
Measurement cct 4
RUP2
Feedback resistance
Built-in capacitance
Rf
CG
CD
Measurement cct 5
Design value. A monitor pattern on a wafer is tested.
SEIKO NPC CORPORATION —5
CF5015 series
Switching Characteristics
2.5V operation (CF5015AL×/CF5015BL×)
VDD = 2.25 to 2.75V, VSS = 0V, Ta = −40 to +85°C unless otherwise noted.
Rating
Parameter
Output rise time
Symbol
tr1
tr2
Output fall time
tf1
tf2
Condition
Duty2
Output disable delay time*2
tPLZ
Output enable delay time*2
tPZL
typ
max
Measurement cct 3, load cct 1,
0.1VDD to 0.9VDD
CL = 15pF
–
3
6
CL = 30pF
–
5
10
Measurement cct 3, load cct 1,
0.9VDD to 0.1VDD
CL = 15pF
–
3
6
CL = 30pF
–
5
10
CL = 15pF
f = 60MHz
45
–
55
%
CL = 30pF
f = 50MHz
45
–
55
%
–
–
100
ns
–
–
100
ns
Duty1
Output duty cycle*1
Unit
min
Measurement cct 3, load cct 1,
VDD = 2.5V, Ta = 25°C
Measurement cct 6, load cct 1, VDD = 2.5V, Ta = 25°C,
CL = 15pF
ns
ns
*1. The duty cycle characteristic is checked the sample chips of each production lot.
*2. Oscillator stop function is built-in. When INHN goes LOW, normal output stops. When INHN goes HIGH, normal output is not resumed until after the
oscillator start-up time has elapsed.
3V operation (CF5015BL×)
VDD = 2.7 to 3.6V, VSS = 0V, Ta = −40 to +85°C unless otherwise noted.
Rating
Parameter
Output rise time
Symbol
tr1
tr2
Output fall time
tf1
tf2
Condition
Duty2
Output disable delay time*2
tPLZ
Output enable delay time*2
tPZL
typ
max
Measurement cct 3, load cct 1,
0.1VDD to 0.9VDD
CL = 15pF
–
2.5
5
CL = 30pF
–
4
8
Measurement cct 3, load cct 1,
0.9VDD to 0.1VDD
CL = 15pF
–
2.5
5
CL = 30pF
–
4
8
CL = 15pF
f = 60MHz
45
–
55
%
CL = 30pF
f = 50MHz
45
–
55
%
–
–
100
ns
–
–
100
ns
Duty1
Output duty cycle*1
Unit
min
Measurement cct 3, load cct 1,
VDD = 3.0V, Ta = 25°C
Measurement cct 6, load cct 1, VDD = 3.0V, Ta = 25°C,
CL = 15pF
ns
ns
*1. The duty cycle characteristic is checked the sample chips of each production lot.
*2. Oscillator stop function is built-in. When INHN goes LOW, normal output stops. When INHN goes HIGH, normal output is not resumed until after the
oscillator start-up time has elapsed.
SEIKO NPC CORPORATION —6
CF5015 series
5V operation (CF5015BL×)
VDD = 4.5 to 5.5V, VSS = 0V, Ta = −40 to +85°C unless otherwise noted.
Rating
Parameter
Symbol
Condition
tr1
Output rise time
tr2
tf1
Output fall time
tf2
Output duty cycle*1
Duty1
Output disable delay time*2
tPLZ
Output enable delay time*2
tPZL
Unit
min
typ
max
Measurement cct 3, load cct 1,
0.1VDD to 0.9VDD
CL = 15pF
–
1.7
3.4
CL = 30pF
–
3
6
Measurement cct 3, load cct 1,
0.9VDD to 0.1VDD
CL = 15pF
–
1.7
3.4
CL = 30pF
–
3
6
Measurement cct 3, load cct 1,
VDD = 5.0V, Ta = 25°C
CL = 30pF
f = 60MHz
45
–
55
%
–
–
100
ns
–
–
100
ns
ns
ns
Measurement cct 6, load cct 1, VDD = 5.0V, Ta = 25°C,
CL = 15pF
*1. The duty cycle characteristic is checked the sample chips of each production lot.
*2. Oscillator stop function is built-in. When INHN goes LOW, normal output stops. When INHN goes HIGH, normal output is not resumed until after the
oscillator start-up time has elapsed.
Current consumption and Output waveform with NPC’s standard crystal
Cb
L
Ca
f [MHz]
R [Ω]
L [mH]
Ca [fF]
Cb [pF]
50
16.12
6.88
1.48
1.18
60*
−
−
−
−
R
* The 60MHz crystal parameter is confidential.
FUNCTIONAL DESCRIPTION
Standby Function
When INHN goes LOW, the oscillator stops and the oscillator output on Q becomes high impedance.
INHN
Q
Oscillator
HIGH (or open)
Any fO, fO/2, fO/4, fO/8 or fO/16 output frequency
Normal operation
LOW
High impedance
Stopped
Power-saving Pull-up Resistor
The INHN pull-up resistance changes in response to the input level (HIGH or LOW). When INHN goes LOW
(standby state), the pull-up resistance becomes large to reduce the current consumption during standby.
SEIKO NPC CORPORATION —7
CF5015 series
MEASUREMENT CIRCUITS
Measurement cct 1
R3
C1
Signal
Generator
Measurement cct 4
VDD
XT
When
measuring VOL
VDD
XT
Q
XTN
INHN
R1
Q
VSS
R2
XTN
INHN
When
measuring VOH
VSS
VDD
VOH
0V
Q output
VDD
VOL
0V
2Vp-p, 10MHz sine wave input signal
C1: 0.001µF
R1: 50Ω
R2: 413Ω (2.5V operation)
525Ω (3V operation)
488Ω (5V operation)
R3: 462Ω (2.5V operation)
575Ω (3V operation)
512Ω (5V operation)
VPR
IPR
A
Measurement cct 5
VDD
XT
Measurement cct 2
VDD
VDD
IRf
VSS
A
IZ
IRf
IZ
A
Q
XTN
INHN
Rf =
Q
XTN
INHN
XT
VDD
IPR
(VPR = V SS)
RUP2 = VDD VPR
IPR
(VPR = 0.7VDD)
V
Q output
RUP1 =
VOH
VSS
V VOL
Measurement cct 6
C1
Signal
Generator
Measurement cct 3
XT
XTN
INHN
VSS
IDD
IST
VDD
X'tal
Q
XTN
INHN
Q
R1
A
VDD
XT
VSS
2Vp-p, 10MHz sine wave input signal
C1: 0.001µF
R1: 50Ω
Load cct 1
Q output
CL
(Including probe
capacitance)
SEIKO NPC CORPORATION —8
CF5015 series
Switching Time Measurement Waveform
Output duty level
Q output
0.9VDD
0.9VDD
0.1VDD
DUTY measurement
voltage (0.5V DD )
0.1VDD
TW
tr
tf
Output duty cycle
DUTY measurement
voltage (0.5V DD)
Q output
TW
DUTY= TW/ T
T
100 (%)
Output Enable/Disable Delay
when the device is in standby, the oscillator stops. When standby is released, the oscillator starts and stable
oscillator output occurs after a short delay.
VIH
INHN
VIL
tPLZ
tPZL
INHN input waveform tr = tf
10ns
Q output
SEIKO NPC CORPORATION —9
CF5015 series
Please pay your attention to the following points at time of using the products shown in this document.
The products shown in this document (hereinafter “Products”) are not intended to be used for the apparatus that exerts harmful influence on
human lives due to the defects, failure or malfunction of the Products. Customers are requested to obtain prior written agreement for such
use from SEIKO NPC CORPORATION (hereinafter “NPC”). Customers shall be solely responsible for, and indemnify and hold NPC free and
harmless from, any and all claims, damages, losses, expenses or lawsuits, due to such use without such agreement. NPC reserves the right
to change the specifications of the Products in order to improve the characteristic or reliability thereof. NPC makes no claim or warranty that
the contents described in this document dose not infringe any intellectual property right or other similar right owned by third parties.
Therefore, NPC shall not be responsible for such problems, even if the use is in accordance with the descriptions provided in this document.
Any descriptions including applications, circuits, and the parameters of the Products in this document are for reference to use the Products,
and shall not be guaranteed free from defect, inapplicability to the design for the mass-production products without further testing or
modification. Customers are requested not to export or re-export, directly or indirectly, the Products to any country or any entity not in
compliance with or in violation of the national export administration laws, treaties, orders and regulations. Customers are requested
appropriately take steps to obtain required permissions or approvals from appropriate government agencies.
SEIKO NPC CORPORATION
15-6, Nihombashi-kabutocho, Chuo-ku,
Tokyo 103-0026, Japan
Telephone: +81-3-6667-6601
Facsimile: +81-3-6667-6611
http://www.npc.co.jp/
Email: [email protected]
NC0206CE
2007.02
SEIKO NPC CORPORATION —10
Similar pages