PHILIPS SC16C2552BIA44

SC16C2552B
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte
FIFOs
Rev. 03 — 12 February 2009
Product data sheet
1. General description
The SC16C2552B is a two channel Universal Asynchronous Receiver and Transmitter
(UART) used for serial data communications. Its principal function is to convert parallel
data into serial data, and vice versa. The UART can handle serial data rates up to
5 Mbit/s.
The SC16C2552B is pin compatible with the PC16552 and ST16C2552. The
SC16C2552B provides enhanced UART functions with 16-byte FIFOs, modem control
interface, DMA mode data transfer and concurrent writes to control registers of both
channels. The DMA mode data transfer is controlled by the FIFO trigger levels and the
RXRDY and TXRDY signals. On-board status registers provide the user with error
indications and operational status. System interrupts and modem control features may be
tailored by software to meet specific user requirements. An internal loopback capability
allows on-board diagnostics. Independent programmable baud rate generators are
provided to select transmit and receive baud rates.
The SC16C2552B operates at 5 V, 3.3 V and 2.5 V and the industrial temperature range,
and is available in a plastic PLCC44 package.
2. Features
n
n
n
n
n
n
n
n
n
n
n
n
n
n
1.
Industrial temperature range (−40 °C to +85 °C)
5 V, 3.3 V and 2.5 V operation
Pin-to-pin compatible to PC16C552, ST16C2552
Up to 5 Mbit/s data rate at 5 V and 3.3 V, and 3 Mbit/s at 2.5 V
5 V tolerant on input only pins1
16-byte transmit FIFO
16-byte receive FIFO with error flags
Independent transmit and receive UART control
Four selectable receive FIFO interrupt trigger levels; fixed transmit FIFO interrupt
trigger level
Modem control functions (CTS, RTS, DSR, DTR, RI, CD)
DMA operation and DMA monitoring via package I/O pins, TXRDY/RXRDY
UART internal register sections A and B may be written to concurrently
Multi-function output allows more package functions with fewer I/O pins
Programmable character lengths (5, 6, 7, 8), with even, odd, or no parity
For data bus pins D7 to D0, see Table 23 “Limiting values”.
SC16C2552B
NXP Semiconductors
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
3. Ordering information
Table 1.
Ordering information
Type number
SC16C2552BIA44
Package
Name
Description
Version
PLCC44
plastic leaded chip carrier; 44 leads
SOT187-2
4. Block diagram
SC16C2552B
A0 to A2
CS
CHSEL
TRANSMIT
SHIFT
REGISTER
TXA, TXB
RECEIVE
FIFO
REGISTERS
RECEIVE
SHIFT
REGISTER
RXA, RXB
DATA BUS
AND
CONTROL
LOGIC
REGISTER
SELECT
LOGIC
INTERCONNECT BUS LINES
AND
CONTROL SIGNALS
D0 to D7
IOR
IOW
RESET
TRANSMIT
FIFO
REGISTERS
DTRA, DTRB
RTSA, RTSB
MFA, MFB
INTA, INTB
TXRDYA, TXRDYB
RXRDYA, RXRDYB
INTERRUPT
CONTROL
LOGIC
CLOCK AND
BAUD RATE
GENERATOR
MODEM
CONTROL
LOGIC
CTSA, CTSB
RIA, RIB
CDA, CDB
DSRA, DSRB
002aaa487
XTAL1
Fig 1.
XTAL2
Block diagram of SC16C2552B
SC16C2552B_3
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 03 — 12 February 2009
2 of 38
SC16C2552B
NXP Semiconductors
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
5. Pinning information
40 CTSA
41 DSRA
42 CDA
1
43 RIA
D0
TXRDYA
2
44 VCC
D2
D1
3
D3
5
4
D4
6
5.1 Pinning
D5
7
39 RXA
D6
8
38 TXA
D7
9
37 DTRA
A0 10
36 RTSA
XTAL1 11
35 MFA
SC16C2552BIA44
GND 12
34 INTA
XTAL2 13
33 VCC
A1 14
32 TXRDYB
A2 15
31 RIB
CHSEL 16
30 CDB
INTB 17
Fig 2.
CTSB 28
DTRB 27
TXB 26
RXB 25
IOR 24
RTSB 23
GND 22
RESET 21
IOW 20
MFB 19
CS 18
29 DSRB
002aaa488
Pin configuration for PLCC44
5.2 Pin description
Table 2.
Pin description
Symbol
Pin
Type
Description
A0
10
I
A1
14
I
Register select. A0 to A2 are used during read and write operations to select the UART
register to read from or write to.
A2
15
I
CDA
42
I
CDB
30
I
CHSEL
16
I
Channel select. UART channel A or B is selected by the logic state of this pin when CS is a
logic 0. A logic 0 on CHSEL selects the UART channel B, while a logic 1 selects UART
channel A. Bit 0 of AFR register can temporarily override CHSEL function, allowing user to
write to both channel registers simultaneously with one write cycle.
CTSA
40
I
CTSB
28
I
Clear to Send A, B (active LOW). These inputs are associated with individual UART
channels A through B. A logic 0 on the CTSn pin indicates the modem or data set is ready to
accept transmit data from the SC16C2552B. Status can be tested by reading MSR[4].
CS
18
I
Carrier detect A, B (active LOW). These inputs are associated with individual UART
channels A through B. A logic 0 on this pin indicates that a carrier has been detected by the
modem for that channel.
Chip select (active LOW). This function selects channel A or channel B in accordance with
the logical state of the CHSEL pin. This allows data to be transferred between the user CPU
and the SC16C2552B.
SC16C2552B_3
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 03 — 12 February 2009
3 of 38
SC16C2552B
NXP Semiconductors
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
Table 2.
Pin description …continued
Symbol
Pin
Type
Description
D0
2
I/O
D1
3
I/O
Data bus (bidirectional). These pins are the 8-bit, 3-state data bus for transferring
information to or from the controlling CPU.
D2
4
I/O
D3
5
I/O
D4
6
I/O
D5
7
I/O
D6
8
I/O
D7
9
I/O
DSRA
41
I
DSRB
29
I
DTRA
37
O
DTRB
27
O
GND
12, 22
I
Signal and power ground.
INTA
34
O
INTB
17
O
Interrupt A, B (active HIGH). This function is associated with individual channel interrupts.
Interrupts are enabled in the Interrupt Enable Register (IER). Interrupt conditions include:
receiver errors, available receiver buffer data, transmit buffer empty, or when a modem
status flag is detected.
IOR
24
I
Read strobe (active LOW). A logic 0 transition on this pin will load the contents of an
internal register defined by address bits A[2:0] onto the SC16C2552B data bus (D[7:0]) for
access by external CPU.
IOW
20
I
Write strobe (active LOW). A logic 0 transition on this pin will transfer the contents of the
data bus (D[7:0]) from the external CPU to an internal register that is defined by address bits
A[2:0].
MFA
35
O
MFB
19
O
Multi-function A, B. This function is associated with an individual channel function, A or B.
User programmable bits 2:1 of the Alternate Function Register (AFR) selects a signal
function or output on these pins. OP2 (interrupt enable), BAUDOUT, and RXRDY are signal
functions that may be selected by the AFR. These signal functions are described as follows:
Data Set Ready A, B (active LOW). These inputs are associated with individual UART
channels A through B. A logic 0 on this pin indicates the modem or data set is powered-on
and is ready for data exchange with the UART.
Data Terminal Ready A, B (active LOW). These outputs are associated with individual
UART channels A through B. A logic 0 on this pin indicates that the SC16C2552B is
powered-on and ready. This pin can be controlled via the modem control register. Writing a
logic 1 to MCR[0] will set the DTRn output to logic 0, enabling the modem. This pin will be a
logic 1 after writing a logic 0 to MCR[0], or after a reset.
OP2. When OP2 is selected, the MFn pin is a logic 0 when MCR[3] is set to a logic 1.
A logic 1 is the default signal condition that is available following a master reset or
power-up.
BAUDOUT. When BAUDOUT function is selected, the 16× baud rate clock output is
available at this pin.
RXRDY. RXRDY is primarily intended for monitoring DMA mode 1 transfers for the receive
data FIFOs. A logic 0 indicates there is receive data to read/unload, i.e., receive ready
status with one or more RX characters available in the FIFO/RHR. This pin is a logic 1
when the FIFO/RHR is empty or when the programmed trigger level has not been
reached. This signal can also be used for single mode transfers (DMA mode 0).
RESET
21
I
Reset (active HIGH). A logic 1 on this pin will reset the internal registers and all the outputs.
The UART transmitter output and the receiver input will be disabled during reset time. See
Section 7.11 “SC16C2552B external reset condition” for initialization details.
RIA
43
I
RIB
31
I
Ring Indicator A, B (active LOW). These inputs are associated with individual UART
channels A through B. A logic 0 on this pin indicates the modem has received a ringing
signal from the telephone line. A logic 1 transition on this input pin will generate an interrupt
if modem status interrupt is enabled.
SC16C2552B_3
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 03 — 12 February 2009
4 of 38
SC16C2552B
NXP Semiconductors
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
Table 2.
Pin description …continued
Symbol
Pin
Type
Description
RTSA
36
O
RTSB
23
O
Request to Send A, B (active LOW). These outputs are associated with individual UART
channels A through B. A logic 0 on the RTSn pin indicates the transmitter is ready to
transmit data. Writing a logic 1 in the modem control register MCR[1] will set this pin to a
logic 0, indicating that the transmitter is ready to transmit data. After a reset, this pin will be
set to a logic 1.
RXA
39
I
RXB
25
I
TXA
38
O
TXB
26
O
TXRDYA
1
O
TXRDYB
32
O
Receive data A, B. These inputs are associated with individual serial channel data to the
SC16C2552B receive input circuits A through B. The RXn signal will be a logic 1 during
reset, idle (no data). During the local Loopback mode, the RXn input pin is disabled and TXn
data is connected to the UART RXn input, internally.
Transmit data A, B. These outputs are associated with individual serial transmit channel
data from the SC16C2552B. The TXn signal will be a logic 1 during reset, idle (no data), or
when the transmitter is disabled. During the local Loopback mode, the TXn output pin is
disabled and TXn data is internally connected to the UART RXn input.
Transmit Ready A, B (active LOW). These outputs provide the TX FIFO/THR status for
individual transmit channels (A, B). TXRDYn is primarily intended for monitoring
DMA mode 1 transfers for the transmit data FIFOs. An individual channel’s TXRDYA,
TXRDYB buffer ready status is indicated by logic 0, i.e., at least one location is empty and
available in the FIFO or THR. This signal can also be used for single mode transfers (DMA
mode 0).
VCC
33, 44
I
Power supply input.
XTAL1
11
I
Crystal or external clock input. Functions as a crystal input or as an external clock input.
A crystal can be connected between this pin and XTAL2 to form an internal oscillator circuit.
Alternatively, an external clock can be connected to this pin to provide custom data rates.
See Section 6.5 “Programmable baud rate generator”.
XTAL2
13
O
Output of the crystal oscillator or buffered clock. (See also XTAL1.) Crystal oscillator
output or buffered clock output. Should be left open if an external clock is connected to
XTAL1.
SC16C2552B_3
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 03 — 12 February 2009
5 of 38
SC16C2552B
NXP Semiconductors
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
6. Functional description
The SC16C2552B provides serial asynchronous receive data synchronization,
parallel-to-serial and serial-to-parallel data conversions for both the transmitter and
receiver sections. These functions are necessary for converting the serial data stream into
parallel data that is required with digital data systems. Synchronization for the serial data
stream is accomplished by adding start and stop bits to the transmit data to form a data
character. Data integrity is ensured by attaching a parity bit to the data character. The
parity bit is checked by the receiver for any transmission bit errors. The SC16C2552B is
fabricated with an advanced CMOS process.
The SC16C2552B is an upward solution that provides a dual UART capability with
16 bytes of transmit and receive FIFO memory, instead of none in the 16C450. The
SC16C2552B is designed to work with high speed modems and shared network
environments that require fast data processing time. Increased performance is realized in
the SC16C2552B by the transmit and receive FIFOs. This allows the external processor to
handle more networking tasks within a given time. In addition, the four selectable receive
FIFO trigger interrupt levels are uniquely provided for maximum data throughput
performance, especially when operating in a multi-channel environment. The FIFO
memory greatly reduces the bandwidth requirement of the external controlling CPU,
increases performance, and reduces power consumption.
The SC16C2552B is capable of operation up to 1.5 Mbit/s with a 24 MHz crystal. With a
crystal or external clock input of 7.3728 MHz, the user can select data rates up to
460.8 kbit/s.
The rich feature set of the SC16C2552B is available through internal registers. Selectable
receive FIFO trigger levels, selectable TX and RX baud rates, and modem interface
controls are all standard features.
6.1 UART A-B functions
The UART provides the user with the capability to bidirectionally transfer information
between an external CPU, the SC16C2552B package, and an external serial device. A
logic 0 on chip select pin CS and a logic 1 on CHSEL allows the user to configure, send
data, and/or receive data via UART channel A. A logic 0 on chip select pin CS and a
logic 0 on CHSEL allows the user to configure, send data, and/or receive data via UART
channel B. Individual channel select functions are shown in Table 3.
Table 3.
Serial port selection
Chip select
UART select
CS = 1
none
CS = 0
UART channel selected as follows:
CHSEL = 1: UART channel A
CHSEL = 0: UART channel B
During a write mode cycle, the setting of AFR[0] to a logic 1 will override the CHSEL
selection and allow a simultaneous write to both UART channel sections. This functional
capability allows the registers in both UART channels to be modified concurrently, saving
individual channel initialization time. Caution should be considered, however, when using
this capability. Any in-process serial data transfer may be disrupted by changing an active
channel’s mode.
SC16C2552B_3
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 03 — 12 February 2009
6 of 38
SC16C2552B
NXP Semiconductors
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
6.2 Internal registers
The SC16C2552B provides two sets of internal registers (A and B) consisting of
13 registers each for monitoring and controlling the functions of each channel of the
UART. These registers are shown in Table 4. The UART registers function as data holding
registers (THR/RHR), interrupt status and control registers (IER/ISR), a FIFO control
register (FCR), line status and control registers (LCR/LSR), modem status and control
registers (MCR/MSR), programmable data rate (clock) control registers (DLL/DLM), a
user accessible scratchpad register (SPR), and an Alternate Function Register (AFR).
Table 4.
A2
Internal registers decoding
A1
A0
Read mode
Write mode
General register set (THR/RHR, IER/ISR, MCR/MSR, FCR, LCR/LSR, SPR)
0
0
0
Receive Holding Register
Transmit Holding Register
0
0
1
Interrupt Enable Register
Interrupt Enable Register
0
1
0
Interrupt Status Register
FIFO Control Register
0
1
1
Line Control Register
Line Control Register
1
0
0
Modem Control Register
Modem Control Register
1
0
1
Line Status Register
n/a
1
1
0
Modem Status Register
n/a
1
1
1
Scratchpad Register
Scratchpad Register
Baud rate register set (DLL/DLM,
AFR)[1]
0
0
0
LSB of Divisor Latch
LSB of Divisor Latch
0
0
1
MSB of Divisor Latch
MSB of Divisor Latch
0
1
0
Alternate Function Register
Alternate Function Register
[1]
The baud rate register and AFR register sets are accessible only when CS is a logic 0 and LCR[7] is a
logic 1 for the register set (A/B) being accessed.
6.3 FIFO operation
The 16 byte transmit and receive data FIFOs are enabled by the FIFO Control Register
(FCR) bit 0. The user can set the receive trigger level via FCR[7:6], but not the transmit
trigger level. The receiver FIFO section includes a time-out function to ensure data is
delivered to the external CPU. A time-out interrupt is generated whenever the Receive
Holding Register (RHR) has not been read following the loading of a character, or the
receive trigger interrupt is generated when RX FIFO level is equal to the program RX
trigger value.
6.4 Time-out interrupts
The interrupts are enabled by IER[3:0]. Care must be taken when handling these
interrupts. Following a reset, if the transmitter interrupt is enabled, the SC16C2552B will
issue an interrupt to indicate that the Transmit Holding Register is empty. The ISR register
provides the current singular highest priority interrupt only. A condition can exist where a
higher priority interrupt may mask the lower priority interrupt(s). Only after servicing the
higher pending interrupt will the lower priority interrupt(s) be reflected in the status
register. Servicing the interrupt without investigating further interrupt conditions can result
in data errors.
SC16C2552B_3
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 03 — 12 February 2009
7 of 38
SC16C2552B
NXP Semiconductors
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
When two interrupt conditions have the same priority, it is important to service these
interrupts correctly. Receive Data Ready and Receive Time-Out have the same interrupt
priority (when enabled by IER[0]). The receiver issues an interrupt after the number of
characters have reached the programmed trigger level. In this case, the SC16C2552B
FIFO may hold more characters than the programmed trigger level. Following the removal
of a data byte, the user should re-check LSR[0] for additional characters. A Receive
Time-Out will not occur if the receive FIFO is empty. The time-out counter is reset at the
center of each stop bit received or each time the receive holding register (RHR) is read.
The actual time-out value is 4 character time.
6.5 Programmable baud rate generator
The SC16C2552B supports high speed modem technologies that have increased input
data rates by employing data compression schemes. For example, a 33.6 kbit/s modem
that employs data compression may require a 115.2 kbit/s input data rate. A 128.0 kbit/s
ISDN modem that supports data compression may need an input data rate of 460.8 kbit/s.
A baud rate generator is provided for each UART channel, allowing independent TX/RX
channel control. The programmable Baud Rate Generator (BRG) is capable of accepting
an input clock up to 80 MHz, as required for supporting a 5 Mbit/s data rate. The
SC16C2552B can be configured for internal or external clock operation. For internal clock
oscillator operation, an industry standard microprocessor crystal is connected externally
between the XTAL1 and XTAL2 pins. Alternatively, an external clock can be connected to
the XTAL1 pin to clock the internal baud rate generator for standard or custom rates (see
Table 5).
The generator divides the input 16× clock by any divisor from 1 to (216 − 1). The
SC16C2552B divides the basic external clock by 16. The basic 16× clock provides table
rates to support standard and custom applications using the same system design. The
rate table is configured via the DLL and DLM internal register functions. Customized baud
rates can be achieved by selecting the proper divisor values for the MSB and LSB
sections of baud rate generator.
Programming the baud rate generator registers DLM (MSB) and DLL (LSB) provides a
user capability for selecting the desired final baud rate. The example in Table 5 shows the
selectable baud rate table available when using a 1.8432 MHz external clock input.
XTAL1
XTAL2
X1
1.8432 MHz
C1
22 pF
C2
33 pF
002aab325
Fig 3.
Crystal oscillator connection
SC16C2552B_3
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 03 — 12 February 2009
8 of 38
SC16C2552B
NXP Semiconductors
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
Table 5.
Baud rate generator programming table using a 1.8432 MHz clock
Output
baud rate
Output
16× clock divisor
(decimal)
Output
16× clock divisor
(HEX)
DLM
program value
(HEX)
DLL
program value
(HEX)
50
2304
900
09
00
75
1536
600
06
00
150
768
300
03
00
300
384
180
01
80
600
192
C0
00
C0
1200
96
60
00
60
2400
48
30
00
30
4800
24
18
00
18
7200
16
10
00
10
9600
12
0C
00
0C
19.2 k
6
06
00
06
38.4 k
3
03
00
03
57.6 k
2
02
00
02
115.2 k
1
01
00
01
6.6 DMA operation
The SC16C2552B FIFO trigger level provides additional flexibility to the user for block
mode operation. LSR[6:5] provide an indication when the transmitter is empty or has an
empty location(s). The user can optionally operate the transmit and receive FIFOs in the
DMA mode (FCR[3]). When the transmit and receive FIFOs are enabled and the DMA
mode is de-activated (DMA Mode 0), the SC16C2552B activates the interrupt output pin
for each data transmit or receive operation. When DMA mode is activated (DMA Mode 1),
the user takes the advantage of block mode operation by loading or unloading the FIFO in
a block sequence determined by the receive trigger level and the transmit FIFO. In this
mode, the SC16C2552B sets the interrupt output pin when characters in the transmit
FIFO is below 16, or the characters in the receive FIFOs are above the receive trigger
level.
6.7 Loopback mode
The internal loopback capability allows on-board diagnostics. In the Loopback mode, the
normal modem interface pins are disconnected and reconfigured for loopback internally.
MCR[3:0] register bits are used for controlling loopback diagnostic testing. In the
Loopback mode, INT enable and MCR[2] in the MCR register (bits 3:2) control the modem
RI and CD inputs, respectively. MCR signals DTR (bit 0) and RTS (bit 1) are used to
control the modem DSR and CTS inputs, respectively. The transmitter output (TX) and the
receiver input (RX) are disconnected from their associated interface pins, and instead are
connected together internally (see Figure 4). The CTS, DSR, CD, and RI are
disconnected from their normal modem control inputs pins, and instead are connected
internally to RTS, DTR, OP2 and OP1. Loopback test data is entered into the transmit
holding register via the user data bus interface, D0 to D7. The transmit UART serializes
the data and passes the serial data to the receive UART via the internal loopback
connection. The receive UART converts the serial data back into parallel data that is then
SC16C2552B_3
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 03 — 12 February 2009
9 of 38
SC16C2552B
NXP Semiconductors
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
made available at the user data interface D0 to D7. The user optionally compares the
received data to the initial transmitted data for verifying error-free operation of the UART
TX/RX circuits.
In this mode, the receiver and transmitter interrupts are fully operational. The Modem
Control Interrupts are also operational. However, the interrupts can only be read using
lower four bits of the Modem Status Register (MSR[3:0]) instead of the four Modem Status
Register bits 7:4. The interrupts are still controlled by the IER.
SC16C2552B
D0 to D7
IOR
IOW
RESET
TRANSMIT
FIFO
REGISTERS
TRANSMIT
SHIFT
REGISTER
TXA, TXB
DATA BUS
AND
CONTROL
LOGIC
A0 to A2
CS
CHSEL
REGISTER
SELECT
LOGIC
INTERCONNECT BUS LINES
AND
CONTROL SIGNALS
MCR[4] = 1
RECEIVE
FIFO
REGISTERS
RECEIVE
SHIFT
REGISTER
RXA, RXB
RTSA, RTSB
CTSA, CTSB
DTRA, DTRB
MODEM
CONTROL
LOGIC
INTA, INTB
TXRDYA, TXRDYB
RXRDYA, RXRDYB
INTERRUPT
CONTROL
LOGIC
DSRA, DSRB
(OP1A, OP1B)
CLOCK AND
BAUD RATE
GENERATOR
RIA, RIB
(OP2A, OP2B)
CDA, CDB
002aaa489
XTAL1
Fig 4.
XTAL2
Internal Loopback mode diagram
SC16C2552B_3
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 03 — 12 February 2009
10 of 38
SC16C2552B
NXP Semiconductors
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
7. Register descriptions
Table 6 details the assigned bit functions for the SC16C2552B internal registers. The
assigned bit functions are further defined in Section 7.1 through Section 7.11.
Table 6.
SC16C2552B internal registers
A2
A0
A1
Register Default[1] Bit 7
General register
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
bit 2
set[2]
0
0
0
RHR
XX
bit 7
bit 6
0
0
0
THR
XX
bit 7
bit 6
bit 5
bit 4
bit 3
bit 1
bit 0
0
0
1
IER
00
0
0
0
0
modem receive
status
line
interrupt status
interrupt
transmit
holding
register
interrupt
receive
holding
register
0
1
0
FCR
00
RCVR
trigger
(MSB)
RCVR
trigger
(LSB)
0
0
DMA
mode
select
XMIT
FIFO
reset
RCVR
FIFO
reset
FIFOs
enable
0
1
0
ISR
01
FIFOs
enabled
FIFOs
enabled
0
0
INT
priority
bit 2
INT
priority
bit 1
INT
priority
bit 0
INT
status
0
1
1
LCR
00
divisor
latch
enable
set break set parity even
parity
parity
enable
stop bits word
length
bit 1
word
length
bit 0
1
0
0
MCR
00
0
0
loopback OP2
output
control
OP1
RTS
DTR
1
0
1
LSR
60
FIFO
data
error
THR and THR
TSR
empty
empty
break
interrupt
parity
error
overrun
error
receive
data
ready
1
1
0
MSR
X0
CD
RI
DSR
CTS
∆CD
∆RI
∆DSR
∆CTS
1
1
1
SPR
FF
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
XX
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
0
framing
error
Special register set[3]
0
0
0
DLL
0
0
1
DLM
XX
bit 15
bit 14
bit 13
bit 12
bit 11
bit 10
bit 9
bit 8
0
1
0
AFR
00
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
[1]
The value shown represents the register’s initialized hexadecimal value; X = not applicable.
[2]
The ‘General register set’ registers are accessible only when CS is a logic 0 and LCR[7] is logic 0.
[3]
The Baud rate register and AFR register sets are accessible only when CS is a logic 0 and LCR[7] is a logic 1.
Set A is accessible when CHSEL is a logic 1, and Set B is accessible when CHSEL is a logic 0.
SC16C2552B_3
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 03 — 12 February 2009
11 of 38
SC16C2552B
NXP Semiconductors
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
7.1 Transmit Holding Register (THR) and Receive Holding Register (RHR)
The serial transmitter section consists of an 8-bit Transmit Hold Register (THR) and
Transmit Shift Register (TSR). The status of the THR is provided in the Line Status
Register (LSR). Writing to the THR transfers the contents of the data bus (D7 through D0)
to the TSR and UART via the THR, providing that the THR is empty. The THR empty flag
in the LSR[5] register will be set to a logic 1 when the transmitter is empty or when data is
transferred to the TSR.
The serial receive section also contains an 8-bit Receive Holding Register (RHR) and a
Receive Serial Shift Register (RSR). Receive data is removed from the SC16C2552B and
receive FIFO by reading the RHR register. The receive section provides a mechanism to
prevent false starts. On the falling edge of a start or false start bit, an internal receiver
counter starts counting clocks at the 16× clock rate. After 71⁄2 clocks, the start bit time
should be shifted to the center of the start bit. At this time the start bit is sampled, and if it
is still a logic 0 it is validated. Evaluating the start bit in this manner prevents the receiver
from assembling a false character. Receiver status codes will be posted in the LSR.
7.2 Interrupt Enable Register (IER)
The Interrupt Enable Register (IER) masks the interrupts from receiver ready, transmitter
empty, line status and modem status registers. These interrupts would normally be seen
on the INTA, INTB output pins.
Table 7.
Interrupt Enable Register bits description
Bit
Symbol
Description
7:4
IER[7:4]
not used; initialized to logic 0
3
IER[3]
Modem Status Interrupt. This interrupt will be issued whenever there is a
modem status change as reflected in MSR[3:0].
logic 0 = disable the Modem Status Register interrupt (normal default
condition)
logic 1 = enable the Modem Status Register interrupt
2
IER[2]
Receive Line Status interrupt. This interrupt will be issued whenever a receive
data error condition exists as reflected in LSR[4:1].
logic 0 = disable the receiver line status interrupt (normal default condition)
logic 1 = enable the receiver line status interrupt
1
IER[1]
Transmit Holding Register interrupt. In the 16C450 mode, this interrupt will be
issued whenever the THR is empty and is associated with LSR[5]. In the FIFO
modes, this interrupt will be issued whenever the FIFO and THR are empty.
logic 0 = disable the Transmit Holding Register Empty (TXRDY) interrupt
(normal default condition)
logic 1 = enable the TXRDY (ISR level 3) interrupt
0
IER[0]
Receive Holding Register. In the 16C450 mode, this interrupt will be issued
when the RHR has data, or is cleared when the RHR is empty. In the FIFO
mode, this interrupt will be issued when the FIFO has reached the
programmed trigger level or is cleared when the FIFO drops below the trigger
level.
logic 0 = disable the receiver ready (ISR level 2, RXRDY) interrupt (normal
default condition)
logic 1 = enable the RXRDY (ISR level 2) interrupt
SC16C2552B_3
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 03 — 12 February 2009
12 of 38
SC16C2552B
NXP Semiconductors
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
7.2.1 IER versus Transmit/Receive FIFO interrupt mode operation
When the receive FIFO (FCR[0] = logic 1) and receive interrupts (IER[0] = logic 1) are
enabled, the receive interrupts and register status will reflect the following:
• The receive RXRDY interrupt (Level 2 ISR interrupt) is issued to the external CPU
when the receive FIFO has reached the programmed trigger level. It will be cleared
when the receive FIFO drops below the programmed trigger level.
• Receive FIFO status will also be reflected in the user accessible ISR register when
the receive FIFO trigger level is reached. Both the ISR register receive status bit and
the interrupt will be cleared when the FIFO drops below the trigger level.
• The receive data ready bit (LSR[0]) is set as soon as a character is transferred from
the shift register (RSR) to the receive FIFO. It is reset when the FIFO is empty.
• When the Transmit FIFO and interrupts are enabled, an interrupt is generated when
the transmit FIFO is empty due to the unloading of the data by the TSR and UART for
transmission via the transmission media. The interrupt is cleared either by reading the
ISR register or by loading the THR with new data characters.
7.2.2 IER versus Receive/Transmit FIFO polled mode operation
When FCR[0] = logic 1, resetting IER[3:0] enables the SC16C2552B in the FIFO polled
mode of operation. In this mode, interrupts are not generated and the user must poll the
LSR register for TX and/or RX data status. Since the receiver and transmitter have
separate bits in the LSR either or both can be used in the polled mode by selecting
respective transmit or receive control bit(s).
•
•
•
•
•
LSR[0] will be a logic 1 as long as there is one byte in the receive FIFO.
LSR[4:1] will provide the type of receive errors or a receive break, if encountered.
LSR[5] will indicate when the transmit FIFO is empty.
LSR[6] will indicate when both the transmit FIFO and transmit shift register are empty.
LSR[7] will show if any FIFO data errors occurred.
SC16C2552B_3
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 03 — 12 February 2009
13 of 38
SC16C2552B
NXP Semiconductors
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
7.3 FIFO Control Register (FCR)
This register is used to enable the FIFOs, clear the FIFOs, set the receive FIFO trigger
levels and select the DMA mode.
7.3.1 DMA mode
7.3.1.1
Mode 0 (FCR bit 3 = 0)
Set and enable the interrupt for each single transmit or receive operation and is similar to
the 16C450 mode. Transmit Ready (TXRDY) will go to a logic 0 whenever an empty
transmit space is available in the Transmit Holding Register (THR). Receive Ready
(RXRDY) at the MFn pin will go to a logic 0 whenever the Receive Holding Register (RHR)
is loaded with a character and AFR[2:1] is set to the RXRDY mode.
7.3.1.2
Mode 1 (FCR bit 3 = 1)
Set and enable the interrupt in a block mode operation. The transmit interrupt is set when
the transmit FIFO has at least one empty location. TXRDY remains a logic 0 as long as
one empty FIFO location is available. The receive interrupt is set when the receive FIFO
fills to the programmed trigger level. However, the FIFO continues to fill regardless of the
programmed level until the FIFO is full. RXRDY at the MFn pin remains a logic 0 as long
as the FIFO fill level is above the programmed trigger level, and AFR[2:1] is set to the
RXRDY mode.
7.3.2 FIFO mode
Table 8.
FIFO Control Register bits description
Bit
Symbol
Description
7:6
FCR[7:6]
RCVR trigger. These bits are used to set the trigger level for the receive
FIFO interrupt.
An interrupt is generated when the number of characters in the FIFO
equals the programmed trigger level. However, the FIFO will continue to
be loaded until it is full. Refer to Table 9.
5:4
FCR[5:4]
Not used; initialized to logic 0.
3
FCR[3]
DMA mode select.
logic 0 = set DMA mode ‘0’ (normal default condition)
logic 1 = set DMA mode ‘1’
Transmit operation in mode ‘0’: When the SC16C2552B is in the
16C450 mode (FIFOs disabled; FCR[0] = logic 0) or in the FIFO mode
(FIFOs enabled; FCR[0] = logic 1; FCR[3] = logic 0), and when there
are no characters in the transmit FIFO or Transmit Holding Register, the
TXRDYn pin will be a logic 0. Once active, the TXRDYn pin will go to a
logic 1 after the first character is loaded into the Transmit Holding
Register.
Receive operation in mode ‘0’: When the SC16C2552B is in 16C450
mode, or in the FIFO mode (FCR[0] = logic 1; FCR[3] = logic 0) and
there is at least one character in the receive FIFO, the RXRDY signal at
the MFn pin will be a logic 0. Once active, the RXRDY signal at the
MFn pin will go to a logic 1 when there are no more characters in the
receiver. Note that the AFR register must be set to the RXRDY mode
prior to any possible reading of the RXRDY signal.
SC16C2552B_3
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 03 — 12 February 2009
14 of 38
SC16C2552B
NXP Semiconductors
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
Table 8.
Bit
FIFO Control Register bits description …continued
Symbol
3
(continued)
Description
Transmit operation in mode ‘1’: When the SC16C2552B is in FIFO
mode (FCR[0] = logic 1; FCR[3] = logic 1), the TXRDYn pin will be a
logic 1 when the transmit FIFO is completely full. It will be a logic 0 if
one or more FIFO locations are empty.
Receive operation in mode ‘1’: When the SC16C2552B is in FIFO
mode (FCR[0] = logic 1; FCR[3] = logic 1) and the trigger level has been
reached, or a Receive Time-out has occurred, the RXRDY signal at the
MFn pin will go to a logic 0. Once activated, it will go to a logic 1 after
there are no more characters in the FIFO. Note that the AFR register
must be set to the RXRDY mode prior to any possible reading of the
RXRDY signal.
2
FCR[2]
XMIT FIFO reset.
logic 0 = no FIFO transmit reset (normal default condition)
logic 1 = clears the contents of the transmit FIFO and resets the FIFO
counter logic (the Transmit Shift Register is not cleared or altered).
This bit will return to a logic 0 after clearing the FIFO.
1
FCR[1]
RCVR FIFO reset.
logic 0 = no FIFO receive reset (normal default condition)
logic 1 = clears the contents of the receive FIFO and resets the FIFO
counter logic (the Receive Shift Register is not cleared or altered).
This bit will return to a logic 0 after clearing the FIFO.
0
FCR[0]
FIFOs enabled.
logic 0 = disable the transmit and receive FIFO (normal default
condition)
logic 1 = enable the transmit and receive FIFO. This bit must be a ‘1’
when other FCR bits are written to or they will not be
programmed.
Table 9.
RCVR trigger levels
FCR[7]
FCR[6]
RX FIFO trigger level
0
0
01
0
1
04
1
0
08
1
1
14
SC16C2552B_3
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 03 — 12 February 2009
15 of 38
SC16C2552B
NXP Semiconductors
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
7.4 Interrupt Status Register (ISR)
The SC16C2552B provides four levels of prioritized interrupts to minimize external
software interaction. The Interrupt Status Register (ISR) provides the user with four
interrupt status bits. Performing a read cycle on the ISR will provide the user with the
highest pending interrupt level to be serviced. No other interrupts are acknowledged until
the pending interrupt is serviced. Whenever the interrupt status register is read, the
interrupt status is cleared. However, it should be noted that only the current pending
interrupt is cleared by the read. A lower level interrupt may be seen after re-reading the
interrupt status bits. Table 10 shows the data values (bits 3:0) for the four prioritized
interrupt levels and the interrupt sources associated with each of these interrupt levels.
Table 10.
Interrupt source
Priority
level
ISR[3]
ISR[2]
ISR[1]
ISR[0]
Source of the interrupt
1
0
1
1
0
LSR (Receiver Line Status Register)
2
0
1
0
0
RXRDY (Received Data Ready)
2
1
1
0
0
RXRDY (Receive Data Time-out)
3
0
0
1
0
TXRDY (Transmitter Holding Register empty)
4
0
0
0
0
MSR (Modem Status Register)
Table 11.
Interrupt Status Register bits description
Bit
Symbol
Description
7:6
ISR[7:6]
FIFOs enabled. These bits are set to a logic 0 when the FIFOs are not being
used in the 16C450 mode. They are set to a logic 1 when the FIFOs are
enabled in the SC16C2552B mode.
5:4
ISR[5:4]
not used; initialized to a logic 0
3:1
ISR[3:1]
INT priority bits. These bits indicate the source for a pending interrupt at
interrupt priority levels 1, 2 and 3 (see Table 10).
0
ISR[0]
INT status.
logic 0 or cleared = default condition
logic 0 = an interrupt is pending and the ISR contents may be used as a
pointer to the appropriate interrupt service routine
logic 1 = no interrupt pending (normal default condition)
SC16C2552B_3
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 03 — 12 February 2009
16 of 38
SC16C2552B
NXP Semiconductors
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
7.5 Line Control Register (LCR)
The Line Control Register is used to specify the asynchronous data communication
format. The word length, the number of stop bits and the parity are selected by writing the
appropriate bits in this register.
Table 12.
Line Control Register bits description
Bit
Symbol
Description
7
LCR[7]
Divisor latch enable. The internal baud rate counter latch and Enhanced
Feature mode enable.
logic 0 = divisor latch disabled (normal default condition)
logic 1 = divisor latch enabled
6
LCR[6]
Set break. When enabled, the Break control bit causes a break condition
to be transmitted (the TX output is forced to a logic 0 state). This
condition exists until disabled by setting LCR[6] to a logic 0.
logic 0 = no TX break condition (normal default condition)
logic 1 = forces the transmitter output (TX) to a logic 0 for alerting the
remote receiver to a line break condition
5:3
LCR[5:3]
Programs the parity conditions (see Table 13)
2
LCR[2]
Stop bits. The length of stop bit is specified by this bit in conjunction with
the programmed word length (see Table 14).
logic 0 or cleared = default condition
1:0
LCR[1:0]
Word length bits 1, 0. These two bits specify the word length to be
transmitted or received (see Table 15).
logic 0 or cleared = default condition
Table 13.
LCR[5:3] parity selection
LCR[5]
LCR[4]
LCR[3]
Parity selection
X
X
0
no parity
X
0
1
odd parity
0
1
1
even parity
0
0
1
forced parity ‘1’
1
1
1
forced parity ‘0’
Table 14.
LCR[2] stop bit length
LCR[2]
Word length (bits)
Stop bit length (bit times)
0
5, 6, 7, 8
1
1
5
11⁄2
1
6, 7, 8
2
Table 15.
LCR[1:0] word length
LCR[1]
LCR[0]
Word length (bits)
0
0
5
0
1
6
1
0
7
1
1
8
SC16C2552B_3
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 03 — 12 February 2009
17 of 38
SC16C2552B
NXP Semiconductors
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
7.6 Modem Control Register (MCR)
This register controls the interface with the modem or a peripheral device.
Table 16.
Modem Control Register bits description
Bit
Symbol
Description
7:5
MCR[7:5]
reserved; initialized to a logic 0
4
MCR[4]
Loopback. Enable the local Loopback mode (diagnostics). In this mode the
transmitter output (TX) and the receiver input (RX), CTS, DSR, CD and RI
are disconnected from the SC16C2552B I/O pins. Internally the modem
data and control pins are connected into a loopback data configuration
(see Figure 4). In this mode, the receiver and transmitter interrupts remain
fully operational. The modem control interrupts are also operational, but
the interrupts’ sources are switched to the lower four bits of the Modem
Control. Interrupts continue to be controlled by the IER register.
logic 0 = disable Loopback mode (normal default condition)
logic 1 = enable local Loopback mode (diagnostics)
3
MCR[3]
OP2. Used to control the modem CD signal in the Loopback mode.
logic 0 = sets OP2 to a logic 1 (normal default condition). In the
Loopback mode, sets CD internally to a logic 1.
logic 1 = sets OP2 to a logic 0. In the Loopback mode, sets CD internally
to a logic 0.
2
MCR[2]
OP1. This bit is used in the Loopback mode only. In the Loopback mode,
this bit is used to write the state of the modem RI interface signal.
1
MCR[1]
RTS
logic 0 = force RTS output to a logic 1 (normal default condition)
logic 1 = force RTS output to a logic 0
0
MCR[0]
DTR
logic 0 = force DTR output to a logic 1 (normal default condition)
logic 1 = force DTR output to a logic 0
SC16C2552B_3
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 03 — 12 February 2009
18 of 38
SC16C2552B
NXP Semiconductors
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
7.7 Line Status Register (LSR)
This register provides the status of data transfers between the SC16C2552B and
the CPU.
Table 17.
Line Status Register bits description
Bit
Symbol
Description
7
LSR[7]
FIFO data error.
logic 0 = no error (normal default condition)
logic 1 = at least one parity error, framing error or break indication is in the
current FIFO data. This bit is cleared when RHR register is read.
6
LSR[6]
THR and TSR empty. This bit is the Transmit Empty indicator. This bit is set to a
logic 1 whenever the Transmit Holding Register and the Transmit Shift Register
are both empty. It is reset to logic 0 whenever either the THR or TSR contains a
data character. In the FIFO mode, this bit is set to logic 1 whenever the Transmit
FIFO and Transmit Shift Register are both empty.
5
LSR[5]
THR empty. This bit is the Transmit Holding Register Empty indicator. This bit
indicates that the UART is ready to accept a new character for transmission. In
addition, this bit causes the UART to issue an interrupt to CPU when the THR
interrupt enable is set. The THR bit is set to a logic 1 when a character is
transferred from the Transmit Holding Register into the Transmit Shift Register.
The bit is reset to a logic 0 concurrently with the loading of the Transmit Holding
Register by the CPU. In the FIFO mode, this bit is set when the transmit FIFO is
empty; it is cleared when at least 1 byte is written to the transmit FIFO.
4
LSR[4]
Break interrupt.
logic 0 = no break condition (normal default condition)
logic 1 = the receiver received a break signal (RX was a logic 0 for one
character frame time). In the FIFO mode, only one break character is loaded
into the FIFO.
3
LSR[3]
Framing error.
logic 0 = no framing error (normal default condition)
logic 1 = framing error. The receive character did not have a valid stop bit(s). In
the FIFO mode, this error is associated with the character at the top of the
FIFO.
2
LSR[2]
Parity error.
logic 0 = no parity error (normal default condition
logic 1 = parity error. The receive character does not have correct parity
information and is suspect. In the FIFO mode, this error is associated with the
character at the top of the FIFO.
1
LSR[1]
Overrun error.
logic 0 = no overrun error (normal default condition)
logic 1 = overrun error. A data overrun error occurred in the Receive Shift
Register. This happens when additional data arrives while the FIFO is full. In
this case, the previous data in the shift register is overwritten. Note that under
this condition, the data byte in the Receive Shift Register is not transferred into
the FIFO, therefore the data in the FIFO is not corrupted by the error.
0
LSR[0]
Receive data ready.
logic 0 = no data in Receive Holding Register or FIFO (normal default
condition)
logic 1 = data has been received and is saved in the Receive Holding Register
or FIFO
SC16C2552B_3
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 03 — 12 February 2009
19 of 38
SC16C2552B
NXP Semiconductors
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
7.8 Modem Status Register (MSR)
This register provides the current state of the control interface signals from the modem or
other peripheral device to which the SC16C2552B is connected. Four bits of this register
are used to indicate the changed information. These bits are set to a logic 1 whenever a
control input from the modem changes state. These bits are set to a logic 0 whenever the
CPU reads this register.
Table 18.
Modem Status Register bits description
Bit
Symbol
Description
7
MSR[7]
Carrier Detect, CD. During normal operation, this bit is the complement of the
CD input. Reading this bit in the Loopback mode produces the state of
MCR[3] (OP2A/OP2B).
6
MSR[6]
Ring Indicator, RI. During normal operation, this bit is the complement of the
RI input. Reading this bit in the Loopback mode produces the state of
MCR[2] (OP1A/OP2A).
5
MSR[5]
Data Set Ready, DSR. During normal operation, this bit is the complement of
the DSR input. During the Loopback mode, this bit is equivalent to MCR[0]
(DTR).
4
MSR[4]
Clear To Send, CTS. During normal operation, this bit is the complement of
the CTS input. During the Loopback mode, this bit is equivalent to MCR[1]
(RTS).
3
MSR[3]
∆CD [1]
logic 0 = no CD change (normal default condition)
logic 1 = the CD input to the SC16C2552B has changed state since the
last time it was read. A modem Status Interrupt will be generated.
2
MSR[2]
∆RI [1]
logic 0 = no RI change (normal default condition)
logic 1 = the RI input to the SC16C2552B has changed from a logic 0 to a
logic 1. A modem Status Interrupt will be generated.
1
MSR[1]
∆DSR [1]
logic 0 = no DSR change (normal default condition)
logic 1 = the DSR input to the SC16C2552B has changed state since the
last time it was read. A modem Status Interrupt will be generated.
0
MSR[0]
∆CTS [1]
logic 0 = no CTS change (normal default condition)
logic 1 = the CTS input to the SC16C2552B has changed state since the
last time it was read. A modem Status Interrupt will be generated.
[1]
Whenever any MSR bit 3:0 is set to logic 1, a Modem Status Interrupt will be generated.
SC16C2552B_3
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 03 — 12 February 2009
20 of 38
SC16C2552B
NXP Semiconductors
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
7.9 Scratchpad Register (SPR)
The SC16C2552B provides a temporary data register to store 8 bits of user information.
7.10 Alternate Function Register (AFR)
This is a read/write register used to select specific modes of MF operation and to allow
both UART register’s sets to be written concurrently.
Table 19.
Alternate Function Register bit description
Bit
Symbol
Description
7:3
AFR[7:3]
Not used. All are initialized to logic 0.
2:1
AFR[2:1]
Selects a signal function for output on the MFA, MFB pins. These signal
functions are described as: OP2 (interrupt enable), BAUDOUT, or RXRDY.
Only one signal function can be selected at a time. See Table 20.
0
AFR[0]
When this bit is set, CPU can write concurrently to the same register in both
UARTs. This function is intended to reduce the dual UART initialization time.
It can be used by CPU when both channels are initialized to the same state.
The external CPU can set or clear this bit by accessing either register set.
When this bit is set, the Channel Select pin, CHSEL, still selects the channel
to be accessed during read operation. Setting or clearing this bit has no
effect on read operations. The user should ensure that LCR[7] of both
channels are in the same state before executing a concurrent write to the
registers at address 0, 1, or 2.
logic 0 = no concurrent write (normal default condition)
logic 1 = register set A and B are written concurrently with a single external
CPU I/O write operation.
Table 20.
MFA, MFB function selection
AFR[2]
AFR[1]
MF function
0
0
OP2
0
1
BAUDOUT
1
0
RXRDY
1
1
reserved
SC16C2552B_3
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 03 — 12 February 2009
21 of 38
SC16C2552B
NXP Semiconductors
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
7.11 SC16C2552B external reset condition
Table 21.
Reset state for registers
Register
Reset state
IER
IER[7:0] = 0
ISR
ISR[7:1] = 0; ISR[0] = 1
LCR
LCR[7:0] = 0
MCR
MCR[7:0] = 0
LSR
LSR[7] = 0; LSR[6:5] = 1; LSR[4:0] = 0
MSR
MSR[7:4] = input signals; MSR[3:0] = 0
FCR
FCR[7:0] = 0
AFR
AFR[7:0] = 0
Table 22.
Reset state for outputs
Output
Reset state
TXA, TXB
HIGH
OP2A, OP2B
HIGH
RTSA, RTSB
HIGH
DTRA, DTRB
HIGH
INTA, INTB
LOW
TXRDYA, TXRDYB
LOW
8. Limiting values
Table 23. Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134).
Symbol
Parameter
VCC
supply voltage
Vn
voltage on any other pin
Tamb
Conditions
Max
Unit
-
7
V
at D7 to D0 pins
GND − 0.3
VCC + 0.3
V
at input only pins
GND − 0.3
5.3
V
−40
+85
°C
operating temperature
Tstg
storage temperature
−65
+150
°C
Ptot/pack
total power dissipation
per package
-
500
mW
SC16C2552B_3
Product data sheet
Min
© NXP B.V. 2009. All rights reserved.
Rev. 03 — 12 February 2009
22 of 38
SC16C2552B
NXP Semiconductors
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
9. Static characteristics
Table 24. Static characteristics
Tamb = −40 °C to +85 °C; tolerance of VCC ± 10 %; unless otherwise specified.
Symbol
Parameter
Conditions
VCC = 2.5 V
VCC = 3.3 V
VCC = 5.0 V
Min
Max
Min
Max
Min
Max
Unit
VIL(clk)
clock LOW-level input
voltage
−0.3
+0.45
−0.3
+0.6
−0.5
+0.6
V
VIH(clk)
clock HIGH-level input
voltage
1.8
VCC
2.4
VCC
3.0
VCC
V
VIL
LOW-level input voltage
except X1 clock
−0.3
+0.65
−0.3
+0.8
−0.5
+0.8
V
VIH
HIGH-level input voltage
except X1 clock
1.6
-
2.0
-
2.2
-
V
VOL
LOW-level output voltage
on all outputs[1]
IOL = 5 mA
(data bus)
-
-
-
-
-
0.4
V
IOL = 4 mA
(other outputs)
-
-
-
0.4
-
-
V
IOL = 2 mA
(data bus)
-
0.4
-
-
-
-
V
IOL = 1.6 mA
(other outputs)
-
0.4
-
-
-
-
V
-
-
-
-
2.4
-
V
IOH = −1 mA
(other outputs)
-
-
2.0
-
-
-
V
IOH = −800 µA
(data bus)
1.85
-
-
-
-
-
V
IOH = −400 µA
(other outputs)
1.85
-
-
-
-
-
V
VOH
HIGH-level output voltage IOH = −5 mA
(data bus)
ILIL
LOW-level input leakage
current
-
±10
-
±10
-
±10
µA
IL(clk)
clock leakage current
-
±30
-
±30
-
±30
µA
ICC
supply current
-
3.5
-
4.5
-
4.5
mA
Ci
input capacitance
-
5
-
5
-
5
pF
[1]
f = 5 MHz
Except XTAL2, VOL = 1 V typical.
SC16C2552B_3
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 03 — 12 February 2009
23 of 38
SC16C2552B
NXP Semiconductors
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
10. Dynamic characteristics
Table 25. Dynamic characteristics
Tamb = −40 °C to +85 °C; tolerance of VCC ± 10 %; unless otherwise specified.
Symbol
Parameter
Conditions
VCC = 2.5 V
VCC = 3.3 V
VCC = 5.0 V
Min
Max
Min
Max
Min
Max
Unit
tWH
pulse width HIGH
10
-
6
-
6
-
ns
tWL
pulse width LOW
10
-
6
-
6
-
ns
-
48
-
80
0
-
0
-
[1][2]
fXTAL1
frequency on pin XTAL1
t6s
address set-up time
t6h
address hold time
0
-
0
-
0
-
ns
t7d
IOR delay from chip select
10
-
10
-
10
-
ns
t7w
IOR strobe width
77
-
26
-
23
-
ns
t7h
chip select hold time from
IOR
0
-
0
-
0
-
ns
t9d
read cycle delay
25 pF load
20
-
20
-
20
-
ns
t12d
delay from IOR to data
25 pF load
-
77
-
26
-
23
ns
t12h
data disable time
25 pF load
-
15
-
15
-
15
ns
25 pF load
80
0
-
MHz
ns
t13d
IOW delay from chip select
10
-
10
-
10
-
ns
t13w
IOW strobe width
20
-
20
-
15
-
ns
t13h
chip select hold time from
IOW
0
-
0
-
0
-
ns
t15d
write cycle delay
25
-
25
-
20
-
ns
t16s
data set-up time
20
-
20
-
15
-
ns
t16h
data hold time
15
-
5
-
5
-
ns
t17d
delay from IOW to output
25 pF load
-
100
-
33
-
29
ns
t18d
delay to set interrupt from
Modem input
25 pF load
-
100
-
24
-
23
ns
t19d
delay to reset interrupt from 25 pF load
IOR
-
100
-
24
-
23
ns
t20d
delay from stop to set
interrupt
-
TRCLK
-
TRCLK
-
TRCLK
s
t21d
delay from IOR to reset
interrupt
-
100
-
29
-
28
ns
t22d
delay from start to set
interrupt
-
100
-
45
-
40
ns
t23d
delay from IOW to transmit
start
t24d
delay from IOW to reset
interrupt
t25d
delay from stop to set
RXRDY
t26d
t27d
[3]
25 pF load
[3]
8TRCLK 24TRCLK 8TRCLK 24TRCLK 8TRCLK 24TRCLK s
-
100
-
45
-
40
ns
-
TRCLK
-
TRCLK
-
TRCLK
s
delay from IOR to reset
RXRDY
-
100
-
45
-
40
ns
delay from IOW to set
TXRDY
-
100
-
45
-
40
ns
[3]
SC16C2552B_3
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 03 — 12 February 2009
24 of 38
SC16C2552B
NXP Semiconductors
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
Table 25. Dynamic characteristics …continued
Tamb = −40 °C to +85 °C; tolerance of VCC ± 10 %; unless otherwise specified.
Symbol
Parameter
Conditions
VCC = 2.5 V
t28d
delay from start to reset
TXRDY
[3]
tRESET
RESET pulse width
[4]
N
baud rate divisor
VCC = 3.3 V
VCC = 5.0 V
Unit
Min
Max
Min
Max
Min
Max
-
8TRCLK
-
8TRCLK
-
8TRCLK
s
200
-
40
-
40
-
ns
(216
1
− 1)
1
(216
− 1)
[1]
Applies to external clock, crystal oscillator max 24 MHz.
[2]
Maximum frequency = ---------------
[3]
RCLK is an internal signal derived from divisor latch LSB (DLL) and divisor latch MSB (DLM) divisor latches.
[4]
Reset pulse must happen when these signals are inactive: CS, IOW, IOR.
1
(216
− 1)
1
t w ( clk )
10.1 Timing diagrams
t6h
valid
address
A0 to A2
CHSEL
t13h
t6s
active
CS
t13d
IOW
t13w
t15d
active
t16s
D0 to D7
t16h
data
002aaa128
Fig 5.
General write timing
SC16C2552B_3
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 03 — 12 February 2009
25 of 38
SC16C2552B
NXP Semiconductors
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
t6h
valid
address
A0 to A2
CHSEL
t7h
t6s
active
CS
t7d
t7w
IOR
t9d
active
t12h
t12d
D0 to D7
data
002aaa127
Fig 6.
General read timing
IOW
active
t17d
RTSA, RTSB
DTRA, DTRB
change of state
change of state
CDA, CDB
CTSA, CTSB
DSRA, DSRB
change of state
t18d
INTA, INTB
change of state
t18d
active
active
active
t19d
IOR
active
active
active
t18d
change of state
RIA, RIB
002aaa352
Fig 7.
Modem input/output timing
SC16C2552B_3
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 03 — 12 February 2009
26 of 38
SC16C2552B
NXP Semiconductors
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
tWL
tWH
external clock
tw(clk)
002aac357
1
f XTAL1 = --------------t w ( clk )
Fig 8.
External clock timing
start
bit
RXA, RXB
parity
bit
data bits (0 to 7)
D0
D1
D2
D3
D4
D5
D6
stop
bit
next
data
start
bit
D7
5 data bits
6 data bits
7 data bits
t20d
active
INTA, INTB
t21d
active
IOR
16 baud rate clock
002aae287
Fig 9.
Receive timing
SC16C2552B_3
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 03 — 12 February 2009
27 of 38
SC16C2552B
NXP Semiconductors
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
start
bit
D0
RXA, RXB
parity
bit
data bits (0 to 7)
D1
D2
D3
D4
D5
D6
stop
bit
next
data
start
bit
D7
t25d
active data
ready
RXRDYA, RXRDYB
t26d
active
IOR
002aae288
Fig 10. Receive ready timing in non-FIFO mode
start
bit
RXA, RXB
parity
bit
data bits (0 to 7)
D0
D1
D2
D3
D4
D5
D6
stop
bit
D7
first byte that
reaches the
trigger level
t25d
active data
ready
RXRDYA, RXRDYB
t26d
active
IOR
002aae289
Fig 11. Receive ready timing in FIFO mode
SC16C2552B_3
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 03 — 12 February 2009
28 of 38
SC16C2552B
NXP Semiconductors
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
start
bit
parity
bit
data bits (0 to 7)
TXA, TXB
D0
D1
D2
D3
D4
D5
D6
stop
bit
next
data
start
bit
D7
5 data bits
6 data bits
7 data bits
active
transmitter ready
INTA, INTB
t22d
t24d
t23d
IOW
active
active
16 baud rate clock
002aae290
Fig 12. Transmit timing
start
bit
TXA, TXB
D0
IOW
active
D0 to D7
byte #1
parity
bit
data bits (0 to 7)
D1
D2
D3
D4
D5
D6
stop
bit
next
data
start
bit
D7
t28d
t27d
active
transmitter ready
TXRDYA, TXRDYB
transmitter
not ready
002aae291
Fig 13. Transmit ready timing in non-FIFO mode
SC16C2552B_3
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 03 — 12 February 2009
29 of 38
SC16C2552B
NXP Semiconductors
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
start
bit
data bits (0 to 7)
D0
TXA, TXB
parity
bit
D1
D2
D3
D4
D5
D6
stop
bit
D7
5 data bits
6 data bits
7 data bits
IOW
active
t28d
D0 to D7
byte #16
t27d
TXRDYA, TXRDYB
FIFO full
002aae292
Fig 14. Transmit ready timing in FIFO mode (DMA mode ‘1’)
SC16C2552B_3
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 03 — 12 February 2009
30 of 38
SC16C2552B
NXP Semiconductors
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
11. Package outline
PLCC44: plastic leaded chip carrier; 44 leads
SOT187-2
eD
eE
y
X
39
A
29
28
40
bp
ZE
b1
w M
44
1
E
HE
pin 1 index
A
A4 A1
e
(A 3)
6
β
18
Lp
k
7
detail X
17
e
v M A
ZD
D
B
HD
v M B
0
5
10 mm
scale
DIMENSIONS (mm dimensions are derived from the original inch dimensions)
A4
A1
e
UNIT A
A3
D(1) E(1)
eD
eE
HD
bp b1
max.
min.
4.57
4.19
mm
inches
0.81
0.66
HE
k
16.66 16.66
16.00 16.00 17.65 17.65 1.22
1.27
16.51 16.51
14.99 14.99 17.40 17.40 1.07
0.51
0.25
3.05
0.53
0.33
0.180
0.02
0.165
0.01
0.12
0.021 0.032 0.656 0.656
0.05
0.013 0.026 0.650 0.650
0.63
0.59
0.63
0.59
Lp
v
w
y
1.44
1.02
0.18
0.18
0.1
ZD(1) ZE(1)
max. max.
2.16
β
2.16
45 o
0.695 0.695 0.048 0.057
0.007 0.007 0.004 0.085 0.085
0.685 0.685 0.042 0.040
Note
1. Plastic or metal protrusions of 0.25 mm (0.01 inch) maximum per side are not included.
REFERENCES
OUTLINE
VERSION
IEC
JEDEC
JEITA
SOT187-2
112E10
MS-018
EDR-7319
EUROPEAN
PROJECTION
ISSUE DATE
99-12-27
01-11-14
Fig 15. Package outline SOT187-2 (PLCC44)
SC16C2552B_3
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 03 — 12 February 2009
31 of 38
SC16C2552B
NXP Semiconductors
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
12. Soldering of SMD packages
This text provides a very brief insight into a complex technology. A more in-depth account
of soldering ICs can be found in Application Note AN10365 “Surface mount reflow
soldering description”.
12.1 Introduction to soldering
Soldering is one of the most common methods through which packages are attached to
Printed Circuit Boards (PCBs), to form electrical circuits. The soldered joint provides both
the mechanical and the electrical connection. There is no single soldering method that is
ideal for all IC packages. Wave soldering is often preferred when through-hole and
Surface Mount Devices (SMDs) are mixed on one printed wiring board; however, it is not
suitable for fine pitch SMDs. Reflow soldering is ideal for the small pitches and high
densities that come with increased miniaturization.
12.2 Wave and reflow soldering
Wave soldering is a joining technology in which the joints are made by solder coming from
a standing wave of liquid solder. The wave soldering process is suitable for the following:
• Through-hole components
• Leaded or leadless SMDs, which are glued to the surface of the printed circuit board
Not all SMDs can be wave soldered. Packages with solder balls, and some leadless
packages which have solder lands underneath the body, cannot be wave soldered. Also,
leaded SMDs with leads having a pitch smaller than ~0.6 mm cannot be wave soldered,
due to an increased probability of bridging.
The reflow soldering process involves applying solder paste to a board, followed by
component placement and exposure to a temperature profile. Leaded packages,
packages with solder balls, and leadless packages are all reflow solderable.
Key characteristics in both wave and reflow soldering are:
•
•
•
•
•
•
Board specifications, including the board finish, solder masks and vias
Package footprints, including solder thieves and orientation
The moisture sensitivity level of the packages
Package placement
Inspection and repair
Lead-free soldering versus SnPb soldering
12.3 Wave soldering
Key characteristics in wave soldering are:
• Process issues, such as application of adhesive and flux, clinching of leads, board
transport, the solder wave parameters, and the time during which components are
exposed to the wave
• Solder bath specifications, including temperature and impurities
SC16C2552B_3
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 03 — 12 February 2009
32 of 38
SC16C2552B
NXP Semiconductors
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
12.4 Reflow soldering
Key characteristics in reflow soldering are:
• Lead-free versus SnPb soldering; note that a lead-free reflow process usually leads to
higher minimum peak temperatures (see Figure 16) than a SnPb process, thus
reducing the process window
• Solder paste printing issues including smearing, release, and adjusting the process
window for a mix of large and small components on one board
• Reflow temperature profile; this profile includes preheat, reflow (in which the board is
heated to the peak temperature) and cooling down. It is imperative that the peak
temperature is high enough for the solder to make reliable solder joints (a solder paste
characteristic). In addition, the peak temperature must be low enough that the
packages and/or boards are not damaged. The peak temperature of the package
depends on package thickness and volume and is classified in accordance with
Table 26 and 27
Table 26.
SnPb eutectic process (from J-STD-020C)
Package thickness (mm)
Package reflow temperature (°C)
Volume (mm3)
< 350
≥ 350
< 2.5
235
220
≥ 2.5
220
220
Table 27.
Lead-free process (from J-STD-020C)
Package thickness (mm)
Package reflow temperature (°C)
Volume (mm3)
< 350
350 to 2000
> 2000
< 1.6
260
260
260
1.6 to 2.5
260
250
245
> 2.5
250
245
245
Moisture sensitivity precautions, as indicated on the packing, must be respected at all
times.
Studies have shown that small packages reach higher temperatures during reflow
soldering, see Figure 16.
SC16C2552B_3
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 03 — 12 February 2009
33 of 38
SC16C2552B
NXP Semiconductors
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
maximum peak temperature
= MSL limit, damage level
temperature
minimum peak temperature
= minimum soldering temperature
peak
temperature
time
001aac844
MSL: Moisture Sensitivity Level
Fig 16. Temperature profiles for large and small components
For further information on temperature profiles, refer to Application Note AN10365
“Surface mount reflow soldering description”.
13. Abbreviations
Table 28.
Abbreviations
Acronym
Description
CPU
Central Processing Unit
DLL
Divisor Latch LSB
DLM
Divisor Latch MSB
DMA
Direct Memory Access
FIFO
First In, First Out
ISDN
Integrated Service Digital Network
LSB
Least Significant Bit
MSB
Most Significant Bit
UART
Universal Asynchronous Receiver and Transmitter
SC16C2552B_3
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 03 — 12 February 2009
34 of 38
SC16C2552B
NXP Semiconductors
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
14. Revision history
Table 29.
Revision history
Document ID
Release date
Data sheet status
Change notice
Supersedes
SC16C2552B_3
20090212
Product data sheet
-
SC16C2552B-02
Modifications:
•
The format of this data sheet has been redesigned to comply with the new identity guidelines of
NXP Semiconductors.
•
•
Legal texts have been adapted to the new company name where appropriate.
Section 2 “Features”:
– added (new) 5th bullet item
– added Footnote 1
•
•
Figure 1: changed signal names from “MFA, MFB” to “MFA, MFB”
Section 7.3.1 “DMA mode”:
– 1st paragraph, last sentence: changed from “MF register” to “AFR[2:1]”
– 2nd paragraph, last sentence: changed from “MF register” to “AFR[2:1]”
•
Table 18 “Modem Status Register bits description”:
– description of bit 7: changed from “(OPA/OPB)” to “(OP2A/OP2B)”
– description of bit 6: changed from “(OP1)” to “(OP1A/OP2A)”
•
Table 23 “Limiting values”:
– symbol Vn split to show 2 separate conditions: “at D7 to D0 pins” and “at input only pins”
– changed symbol “Ptot(pack)” to “Ptot/pack”
•
Table 24 “Static characteristics”:
– descriptive line below table title changed from “VCC = 2.5 V, 3.3 V or 5.0 V ± 10 %” to
“tolerance of VCC ± 10 %”
– changed symbol/parameter from “VIL(CK), LOW-level clock input voltage” to “VIL(clk), clock
LOW-level input voltage”
– changed symbol/parameter from “VIH(CK), HIGH-level clock input voltage” to “VIH(clk), clock
HIGH-level input voltage”
– changed symbol/parameter from “ICL, clock leakage” to “IL(clk), clock leakage current”
– Table note [1]: changed from “Except x2” to “Except XTAL2”
•
Table 25 “Dynamic characteristics”:
– descriptive line below table title changed from “VCC = 2.5 V, 3.3 V or 5.0 V ± 10 %” to
“tolerance of VCC ± 10 %”
– changed symbol “t1w, t2w” to 2 separate symbols “tWH” and “tWL”
– changed symbol/parameter “t3w, clock frequency” to “fXTAL1, frequency on pin XTAL1”
– added Table note [2]
– symbols t20d, t23d, t25d and t28d: Unit changed from “Rclk” to “s” (second)
– symbols t20d, t23d, t25d and t28d: appended “TRCLK” to Min and Max values
– added Table note [3]
– symbol N: removed “Rclk” from Unit column (N is a number)
– added Table note [4] and its reference at tRESET
SC16C2552B_3
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 03 — 12 February 2009
35 of 38
SC16C2552B
NXP Semiconductors
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
Table 29.
Revision history …continued
Document ID
Modifications:
(continued)
Release date
•
Data sheet status
Change notice
Supersedes
Section 10.1 “Timing diagrams”:
– Figure 7, Figure 9, Figure 10, Figure 11, Figure 12, Figure 13, Figure 14: appended
(channel) “A” and/or “B” to signal names
– Figure 8 “External clock timing”: changed symbols “t1w, t2w, t3w” to “tWH, tWL, tw(clk)”,
respectively
– Figure 8 “External clock timing”: added equation
– Figure 10, Figure 11, Figure 13, Figure 14: at the top of these drawings, changed phrase
from “DATA BITS (5-8)” to “data bits (0 to 7)”
•
•
updated soldering information
added Section 13 “Abbreviations”
SC16C2552B-02
(9397 750 14442)
20041213
Product data
-
SC16C2552B-01
SC16C2552B-01
(9397 750 11966)
20040330
Product data
-
-
SC16C2552B_3
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 03 — 12 February 2009
36 of 38
SC16C2552B
NXP Semiconductors
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
15. Legal information
15.1 Data sheet status
Document status[1][2]
Product status[3]
Definition
Objective [short] data sheet
Development
This document contains data from the objective specification for product development.
Preliminary [short] data sheet
Qualification
This document contains data from the preliminary specification.
Product [short] data sheet
Production
This document contains the product specification.
[1]
Please consult the most recently issued document before initiating or completing a design.
[2]
The term ‘short data sheet’ is explained in section “Definitions”.
[3]
The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nxp.com.
15.2 Definitions
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. NXP Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences of
use of such information.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is intended
for quick reference only and should not be relied upon to contain detailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local NXP Semiconductors sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
15.3 Disclaimers
General — Information in this document is believed to be accurate and
reliable. However, NXP Semiconductors does not give any representations or
warranties, expressed or implied, as to the accuracy or completeness of such
information and shall have no liability for the consequences of use of such
information.
Right to make changes — NXP Semiconductors reserves the right to make
changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.
Suitability for use — NXP Semiconductors products are not designed,
authorized or warranted to be suitable for use in medical, military, aircraft,
space or life support equipment, nor in applications where failure or
malfunction of an NXP Semiconductors product can reasonably be expected
to result in personal injury, death or severe property or environmental
damage. NXP Semiconductors accepts no liability for inclusion and/or use of
NXP Semiconductors products in such equipment or applications and
therefore such inclusion and/or use is at the customer’s own risk.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. NXP Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) may cause permanent
damage to the device. Limiting values are stress ratings only and operation of
the device at these or any other conditions above those given in the
Characteristics sections of this document is not implied. Exposure to limiting
values for extended periods may affect device reliability.
Terms and conditions of sale — NXP Semiconductors products are sold
subject to the general terms and conditions of commercial sale, as published
at http://www.nxp.com/profile/terms, including those pertaining to warranty,
intellectual property rights infringement and limitation of liability, unless
explicitly otherwise agreed to in writing by NXP Semiconductors. In case of
any inconsistency or conflict between information in this document and such
terms and conditions, the latter will prevail.
No offer to sell or license — Nothing in this document may be interpreted
or construed as an offer to sell products that is open for acceptance or the
grant, conveyance or implication of any license under any copyrights, patents
or other industrial or intellectual property rights.
15.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks
are the property of their respective owners.
16. Contact information
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: [email protected]
SC16C2552B_3
Product data sheet
© NXP B.V. 2009. All rights reserved.
Rev. 03 — 12 February 2009
37 of 38
SC16C2552B
NXP Semiconductors
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
17. Contents
1
2
3
4
5
5.1
5.2
6
6.1
6.2
6.3
6.4
6.5
6.6
6.7
7
7.1
General description . . . . . . . . . . . . . . . . . . . . . . 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Ordering information . . . . . . . . . . . . . . . . . . . . . 2
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Pinning information . . . . . . . . . . . . . . . . . . . . . . 3
Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3
Functional description . . . . . . . . . . . . . . . . . . . 6
UART A-B functions . . . . . . . . . . . . . . . . . . . . . 6
Internal registers. . . . . . . . . . . . . . . . . . . . . . . . 7
FIFO operation . . . . . . . . . . . . . . . . . . . . . . . . . 7
Time-out interrupts . . . . . . . . . . . . . . . . . . . . . . 7
Programmable baud rate generator . . . . . . . . . 8
DMA operation . . . . . . . . . . . . . . . . . . . . . . . . . 9
Loopback mode . . . . . . . . . . . . . . . . . . . . . . . . 9
Register descriptions . . . . . . . . . . . . . . . . . . . 11
Transmit Holding Register (THR) and Receive
Holding Register (RHR) . . . . . . . . . . . . . . . . . 12
7.2
Interrupt Enable Register (IER) . . . . . . . . . . . 12
7.2.1
IER versus Transmit/Receive FIFO
interrupt mode operation. . . . . . . . . . . . . . . . . 13
7.2.2
IER versus Receive/Transmit FIFO
polled mode operation . . . . . . . . . . . . . . . . . . 13
7.3
FIFO Control Register (FCR) . . . . . . . . . . . . . 14
7.3.1
DMA mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
7.3.1.1
Mode 0 (FCR bit 3 = 0) . . . . . . . . . . . . . . . . . . 14
7.3.1.2
Mode 1 (FCR bit 3 = 1) . . . . . . . . . . . . . . . . . . 14
7.3.2
FIFO mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
7.4
Interrupt Status Register (ISR) . . . . . . . . . . . . 16
7.5
Line Control Register (LCR) . . . . . . . . . . . . . . 17
7.6
Modem Control Register (MCR) . . . . . . . . . . . 18
7.7
Line Status Register (LSR) . . . . . . . . . . . . . . . 19
7.8
Modem Status Register (MSR). . . . . . . . . . . . 20
7.9
Scratchpad Register (SPR) . . . . . . . . . . . . . . 21
7.10
Alternate Function Register (AFR) . . . . . . . . . 21
7.11
SC16C2552B external reset condition . . . . . . 22
8
Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . 22
9
Static characteristics. . . . . . . . . . . . . . . . . . . . 23
10
Dynamic characteristics . . . . . . . . . . . . . . . . . 24
10.1
Timing diagrams . . . . . . . . . . . . . . . . . . . . . . . 25
11
Package outline . . . . . . . . . . . . . . . . . . . . . . . . 31
12
Soldering of SMD packages . . . . . . . . . . . . . . 32
12.1
Introduction to soldering . . . . . . . . . . . . . . . . . 32
12.2
Wave and reflow soldering . . . . . . . . . . . . . . . 32
12.3
Wave soldering . . . . . . . . . . . . . . . . . . . . . . . . 32
12.4
Reflow soldering . . . . . . . . . . . . . . . . . . . . . . . 33
13
14
15
15.1
15.2
15.3
15.4
16
17
Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . .
Revision history . . . . . . . . . . . . . . . . . . . . . . .
Legal information . . . . . . . . . . . . . . . . . . . . . .
Data sheet status . . . . . . . . . . . . . . . . . . . . . .
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . .
Disclaimers. . . . . . . . . . . . . . . . . . . . . . . . . . .
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . .
Contact information . . . . . . . . . . . . . . . . . . . .
Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
34
35
37
37
37
37
37
37
38
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section ‘Legal information’.
© NXP B.V. 2009.
All rights reserved.
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: [email protected]
Date of release: 12 February 2009
Document identifier: SC16C2552B_3