Support & More Resources CY3215-DK Development Kit (Emulator) For simple programming a MiniProg is included in the CY3214-PSoCEvalUSB kit. For full emulation you can attach an ICE-Cube to the PSoCEvalUSB board. (The ICE-Cube is available in the CY3215-DK.) CY3214-PSoCEvalUSB Getting Started Guide Getting Started: 1. Verify Kit Contents 2. Install PSoC Designer 3. Install PSoC Programmer 4. Run Example Project ICE-Cube (available in CY3215-DK) Powering the board (9-12V) The PSoCEvalUSB board can be powered by any of the following methods: 1) Separate power supply: recommend Digikey Part T461-P5P-ND. 2) USB: if connected to bus powered hub then not to exceed 100mA, if connected to self powered hub or PC then not to exceed 500mA (consult USB 2.0 spec to determine exact power restrictions). 3) ICE-Cube: not to exceed 100mA. Visit www.cypress.com/psoc for PSoC support. Step 1: Verify Kit Contents LCD Module KIT CONTENTS PSoCEvalUSB board LCD Module MiniProg programming unit USB cable Jumper wire pack PSoC Designer CD-ROM Online Support For knowledgebase articles, customer forums, and online application support, visit www.cypress.com/support. PSoC Device Selector Guide Application Note AN2209, the PSoC Device Selector Guide, is a useful tool for determining exactly which PSoC device you should use for a specific project. Development Tools Selector Guide The PSoC Development Tools Selector Guide includes a complete catalog and description of all the development tools that support PSoC devices. MiniProg programming unit Not Pictured: PSoC Support CD-ROM Getting Started Guide PSoCEvalUSB board Tele-Training Tele-training courses can help you move quickly up the PSoC learning curve. Each training includes example projects. To register for the live training taught by PSoC factory experts or to download a pre-recorded class, visit www.cypress.com/ support/training.cfm. Application Notes Hundreds of PSoC Application Notes are available at www.cypress.com. Many Application Notes include PSoC Designer or PSoC Express Projects for additional support. Web: www.cypress.com Support: www.cypress.com/support/ US: 800.669.0557 Intl: 425.787.4814 PSoC Designer CD-ROM USB cable Jumper wire pack Step 4: Run Example Project Step 2 & 3: Install Software Install PSoC Designer and then PSoC Programmer from the included CD-ROM. For assistance refer to PSoC Designer: Integrated Development Environment User Guide, available on the CD-ROM. Download the latest version and updates of PSoC Designer and PSoC Programmer at www.cypress.com/psoc (Design Resources >> Software & Drivers). Included in this kit is a second CD with example projects. For each example project, first read the accompanying application note, then download and unzip the PSoC Designer Project file to your PC. Finally, read any unzipped readme.txt files and run the “.soc” file in PSoC Designer. PSoCEvalUSB Board Details A LCD: 16x2 Dot Matrix LCD. Hitachi 44780 compatible module. B O C D N E M K F L G J A Contrast Potentiometer (R2): Controls LCD contrast. Buttons (S1 and S2): SPST-NO push-button switches. (Set drive to pull down, drive low). Potentiometers (VR1 and VR2): Two 10K Ohm potentiometers are accessible via VR1 and VR2. Potentiometers are tied to Vss and Vdd. (Set drive to Analog High-Z). G Pin Access: CY8C24x94 GPIO are accessible via clearly labeled headers. J ICE-Cube Connector (J14): Connects to blue cat 5e cable for use with ICE-Cube (available in the CY3215-DK) Jumpers: JP7: Add jumper to regulate connected power supply (J13) to 3.3V instead of 5V (LCD doesn’t work at 3.3V). VBUS: Add jumper to power board via USB instead of from regulated power supply (J13). VREG: Add jumper to power board from regulated power supply (J13). Kit is shipped with jumper added. JP3 & JP4: Add jumper to enable external pull-up resistors for I2C bus (P1[5] and P1[7]). J8 & J11: Connect with jumper wire to bread board for convenient access to the power supply. Various C E H I Loudspeaker (LS1): Magnetic buzzer accessible via LS1. CEM-1206S. (Active high, set drive to strong, drive high). M ISSP Connector (J15): In-System Serial Programmer (ISSP) connector. Connect MiniProg for programming. LEDs (LED1-4): Four LEDs are accessible via headers LED1-4. LEDs are illuminated by connecting the signal to Vss. (Active low, set drive to strong, drive low). USB connector (P1): Mini USB type B connector. (See back for power details) H Breadboard: Use with jumper wires to connect to on board resources. K Legacy DB9 Connector (J1): Connect serial cable (not included) to DB9 connector and serial port on PC. For use with RX, TX, CTS, and RTS via on-board header. N B D F CapSense buttons & slider: Port 5 can be used in the interpolation of a CapSense slider; P3[6] and P3[7] can be used to implement CapSense buttons. I Joystick (JS1): Unpopulated joystick footprint. Can be populated with Digikey part 252A103B60NB-ND. JSV (vertical pot value), JSH (horizontal pot value), and JSW (switch) are accessible via header on-board. L Power Supply Connector (J13): Connect to a 9-12V power supply to supply power to the board. (Recommend Digikey Part T461P5P-ND.) O