MC10H125 Quad MECL−to−TTL Translator The MC10H125 is a quad translator for interfacing data and control signals between the MECL section and saturated logic section of digital systems. The 10H part is a functional/pinout duplication of the standard MECL 10K family part, with 100% improvement in propagation delay, and no increase in power-supply current. Outputs of unused translators will go to low state when their inputs are left open. • Propagation Delay, 2.5 ns Typical • Voltage Compensated • Improved Noise Margin 150 mV (Over Operating Voltage and Temperature Range) • MECL 10K-Compatible http://onsemi.com MARKING DIAGRAMS 16 CDIP CASE 620A MC10H125L AWLYYWW 1 16 PDIP-16 P SUFFIX CASE 648 MC10H125P AWLYYWW 1 1 PLCC-20 FN SUFFIX CASE 775 10H125 AWLYYWW 16 EIAJ-16 M SUFFIX CASE 966 10H125 ALYW 1 A WL YY WW = Assembly Location = Wafer Lot = Year = Work Week ORDERING INFORMATION Device Semiconductor Components Industries, LLC, 2003 May, 2003 - Rev. 11 1 Package Shipping MC10H125L CDIP 25 Units/Rail MC10H125P PDIP-16 25 Units/Rail MC10H125FN PLCC-20 46 Units/Rail MC10H125M EIAJ-16 50 Units/Rail MC10H125MEL EIAJ-16 2000 Units/Reel Publication Order Number: MC10H125/D MC10H125 LOGIC DIAGRAM 2 PIN ASSIGNMENT 4 3 6 5 7 10 12 11 14 13 15 1 VBB* GND = Pin 16 VCC ( +5.0 Vdc) = Pin 9 VEE ( -5.2 Vdc) = Pin 8 VBB 1 16 GND Ain 2 15 Din Ain 3 14 Din Aout 4 13 Dout Bout 5 12 Cout Bin 6 11 Cin Bin 7 10 Cin VEE 8 9 VCC Pin assignment is for Dual-in-Line Package. For PLCC pin assignment, see the Pin Conversion Tables. *VBB to be used to supply bias to the MC10H125 only and bypassed (when used) with 0.01 F to 0.1 F capacitor to ground (0 V). VBB can source < 1.0 mA. DIP CONVERSION TABLES 16-Pin DIL to 20-Pin PLCC 16 PIN DIL 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 20 PIN PLCC 2 3 4 5 7 8 9 10 12 13 14 15 17 18 19 20 20-Pin DIL to 20-Pin PLCC 20 PIN DIL 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 20 PIN PLCC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 http://onsemi.com 2 MC10H125 MAXIMUM RATINGS Symbol Characteristic Rating Unit VEE Power Supply (VCC = 5.0 V) -8.0 to 0 Vdc VCC Power Supply (VEE = -5.2 V) 0 to +7.0 Vdc VI Input Voltage (VCC = 5.0 V) 0 to VEE Vdc TA Operating Temperature Range 0 to +75 °C Tstg Storage Temperature Range -55 to +150 -55 to +165 °C °C - Plastic - Ceramic ELECTRICAL CHARACTERISTICS (VEE = -5.2 V +5%; VCC = 5.0 V + 5.0 %) (Note 2) 0° 25° 75° Min Max Min Max Min Max Unit - 44 - 40 - 44 mA Positive Power Supply D i Current Drain C - 63 - 63 - 63 mA - 40 - 40 - 40 mA IinH Input Current - 225 - 145 - 145 A ICBO Input Leakage Current - 1.5 - 1.0 - 1.0 A VOH High Output Voltage 2.5 - 2.5 - 2.5 - Vdc - 0.5 - 0.5 - 0.5 Vdc Symbol IE Characteristic Negative Power Supply Drain Current ICCH ICCL IOH = -1.0 mA VOL Low Output Voltage IOL = +20 mA VIH High Input Voltage (Note 1) -1.17 -0.84 -1.13 -0.81 -1.07 -0.735 Vdc VIL Low Input Voltage (Note 1) -1.95 -1.48 -1.95 -1.48 -1.95 -1.45 Vdc IOS Short Circuit Current 60 150 60 150 50 150 mA VBB Reference Voltage -1.38 -1.27 -1.35 -1.25 -1.31 -1.19 Vdc - - VCMR Common Mode Range (Note 3) -2.85 to +0.3 V Typical VPP Input Sensitivity (Note 4) 150 mV AC PARAMETERS 0° Symbol Characteristic 25° 75° Min Max Min Max Min Max Unit tpd Propagation Delay 0.8 3.3 0.85 3.35 0.9 3.4 ns tr Rise Time (Note 5) 0.3 1.2 0.3 1.2 0.3 1.2 ns tf Fall Time (Note 5) 0.3 1.2 0.3 1.2 0.3 1.2 ns 1. When VBB is used as the reference voltage. 2. Each MECL 10H series circuit has been designed to meet the specifications shown in the test table, after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 linear fpm is maintained. 3. Differential input not to exceed 1.0 Vdc. 4. 150 mVp- p differential input required to obtain full logic swing on output. 5. Output Voltage = 1.0 V to 2.0 V. RL = 500 to GND and CL = 25 pF to GND. Refer to Figure 1. http://onsemi.com 3 MC10H125 APPLICATION TTL RECEIVER CHARACTERISTIC TEST *CL includes fixture capacitance CL * RL AC TEST LOAD GND Figure 1. TTL Output Loading Used for Device Evaluation APPLICATION INFORMATION The MC10H125 incorporates differential inputs and Schottky TTL “totem pole” outputs. Differential inputs allow for use as an inverting/non-inverting translator or as a differential line receiver. The VBB reference voltage is available on Pin 1 for use in single-ended input biasing. The outputs of the MC10H125 go to a low-logic level whenever the inputs are left floating, and a high-logic output level is achieved with a minimum input level of 150 mVp- p. An advantage of this device is that MECL-level information can be received, via balanced twisted pair lines, in the TTL equipment. This isolates the MECL-logic from the noisy TTL environment. Power supply requirements are ground, +5.0 volts and -5.2 volts. http://onsemi.com 4 MC10H125 PACKAGE DIMENSIONS PLCC-20 FN SUFFIX PLASTIC PLCC PACKAGE CASE 775-02 ISSUE D 0.007 (0.180) B Y BRK -N- M T L−M 0.007 (0.180) U M N S T L−M S G1 0.010 (0.250) S N S D -L- -M- Z W 20 D 1 X V 0.007 (0.180) M T L−M S N S R 0.007 (0.180) M T L−M S N S Z N S S H 0.004 (0.100) G J 0.007 (0.180) M T L−M S N S K1 E -T- K SEATING PLANE F VIEW S G1 0.010 (0.250) S T L−M T L−M VIEW D-D A C S 0.007 (0.180) M T L−M S N S VIEW S S N S NOTES: 1. DATUMS −L−, −M−, AND −N− DETERMINED WHERE TOP OF LEAD SHOULDER EXITS PLASTIC BODY AT MOLD PARTING LINE. 2. DIMENSION G1, TRUE POSITION TO BE MEASURED AT DATUM −T−, SEATING PLANE. 3. DIMENSIONS R AND U DO NOT INCLUDE MOLD FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250) PER SIDE. 4. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 5. CONTROLLING DIMENSION: INCH. 6. THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE BOTTOM BY UP TO 0.012 (0.300). DIMENSIONS R AND U ARE DETERMINED AT THE OUTERMOST EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS, GATE BURRS AND INTERLEAD FLASH, BUT INCLUDING ANY MISMATCH BETWEEN THE TOP AND BOTTOM OF THE PLASTIC BODY. 7. DIMENSION H DOES NOT INCLUDE DAMBAR PROTRUSION OR INTRUSION. THE DAMBAR PROTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE GREATER THAN 0.037 (0.940). THE DAMBAR INTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE SMALLER THAN 0.025 (0.635). http://onsemi.com 5 DIM A B C E F G H J K R U V W X Y Z G1 K1 INCHES MIN MAX 0.385 0.395 0.385 0.395 0.165 0.180 0.090 0.110 0.013 0.019 0.050 BSC 0.026 0.032 0.020 −−− 0.025 −−− 0.350 0.356 0.350 0.356 0.042 0.048 0.042 0.048 0.042 0.056 −−− 0.020 2 10 0.310 0.330 0.040 −−− MILLIMETERS MIN MAX 9.78 10.03 9.78 10.03 4.20 4.57 2.29 2.79 0.33 0.48 1.27 BSC 0.66 0.81 0.51 −−− 0.64 −−− 8.89 9.04 8.89 9.04 1.07 1.21 1.07 1.21 1.07 1.42 −−− 0.50 2 10 7.88 8.38 1.02 −−− MC10H125 CDIP CASE 620A-01 ISSUE O B A A M 16 9 B L 1 8 16X 0.25 (0.010) E F C K T N SEATING PLANE G 16X 0.25 (0.010) M D T A http://onsemi.com 6 M J T B NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 4. DIMENSION F MAY NARROW TO 0.76 (0.030) WHERE THE LEAD ENTERS THE CERAMIC BODY. 5 THIS DRAWING REPLACES OBSOLETE CASE OUTLINE 620−10. DIM A B C D E F G H K L M N INCHES MIN MAX 0.750 0.785 0.240 0.295 −−− 0.200 0.015 0.020 0.050 BSC 0.055 0.065 0.100 BSC 0.008 0.015 0.125 0.170 0.300 BSC 0 15 0.020 0.040 MILLIMETERS MIN MAX 19.05 19.93 6.10 7.49 −−− 5.08 0.39 0.50 1.27 BSC 1.40 1.65 2.54 BSC 0.21 0.38 3.18 4.31 7.62 BSC 0 15 0.51 1.01 MC10H125 PDIP-16 P SUFFIX PLASTIC DIP PACKAGE CASE 648-08 ISSUE R NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL. -A16 9 1 8 B F C DIM A B C D F G H J K L M S L S -T- SEATING PLANE K H G D M J 16 PL 0.25 (0.010) M T A M INCHES MIN MAX 0.740 0.770 0.250 0.270 0.145 0.175 0.015 0.021 0.040 0.70 0.100 BSC 0.050 BSC 0.008 0.015 0.110 0.130 0.295 0.305 0 10 0.020 0.040 STYLE 1: PIN 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. EIAJ-16 M SUFFIX 16 PIN PLASTIC EIAJ PACKAGE CASE966-01 ISSUE O 16 LE 9 Q1 M E HE 1 8 L DETAIL P Z D e VIEW P A A1 b 0.13 (0.005) c M 0.10 (0.004) http://onsemi.com 7 MILLIMETERS MIN MAX 18.80 19.55 6.35 6.85 3.69 4.44 0.39 0.53 1.02 1.77 2.54 BSC 1.27 BSC 0.21 0.38 2.80 3.30 7.50 7.74 0 10 0.51 1.01 CATHODE CATHODE CATHODE CATHODE CATHODE CATHODE CATHODE CATHODE ANODE ANODE ANODE ANODE ANODE ANODE ANODE ANODE NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS D AND E DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS AND ARE MEASURED AT THE PARTING LINE. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 5. THE LEAD WIDTH DIMENSION (b) DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE LEAD WIDTH DIMENSION AT MAXIMUM MATERIAL CONDITION. DAMBAR CANNOT BE LOCATED ON THE LOWER RADIUS OR THE FOOT. MINIMUM SPACE BETWEEN PROTRUSIONS AND ADJACENT LEAD TO BE 0.46 ( 0.018). DIM A A1 b c D E e HE L LE M Q1 Z MILLIMETERS MIN MAX −−− 2.05 0.05 0.20 0.35 0.50 0.18 0.27 9.90 10.50 5.10 5.45 1.27 BSC 7.40 8.20 0.50 0.85 1.10 1.50 10 0 0.70 0.90 −−− 0.78 INCHES MIN MAX −−− 0.081 0.002 0.008 0.014 0.020 0.007 0.011 0.390 0.413 0.201 0.215 0.050 BSC 0.291 0.323 0.020 0.033 0.043 0.059 10 0 0.028 0.035 −−− 0.031 MC10H125 ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. PUBLICATION ORDERING INFORMATION Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: [email protected] JAPAN: ON Semiconductor, Japan Customer Focus Center 2-9-1 Kamimeguro, Meguro-ku, Tokyo, Japan 153-0051 Phone: 81-3-5773-3850 ON Semiconductor Website: http://onsemi.com For additional information, please contact your local Sales Representative. N. American Technical Support: 800-282-9855 Toll Free USA/Canada http://onsemi.com 8 MC10H125/D