LINER LTC1929CG 2-phase, high efficiency,synchronous step-down switching regulator Datasheet

LTC1929/LTC1929-PG
2-Phase, High Efficiency,
Synchronous Step-Down
Switching Regulators
U
FEATURES
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
DESCRIPTIO
The LTC®1929/LTC1929-PG are 2-phase, single output,
synchronous step-down current mode switching regulator controllers that drive N-channel external power MOSFET
stages in a phase-lockable fixed frequency architecture.
The 2-phase controllers drive their two output stages out
of phase at frequencies up to 300kHz to minimize the RMS
ripple currents in both input and output capacitors. The
2-phase technique effectively multiplies the fundamental
frequency by two, improving transient response while
operating each channel at an optimum frequency for
efficiency. Thermal design is also simplified.
2-Phase Single Output Controller
Reduces Required Input Capacitance and Power
Supply Induced Noise
Current Mode Control Ensures Current Sharing
Phase-Lockable Fixed Frequency: 150kHz to 300kHz
True Remote Sensing Differential Amplifier
OPTI-LOOPTM Compensation Improves Transient
Response
±1% Output Voltage Accuracy
Power Good Output Voltage Monitor (LTC1929-PG)
Wide VIN Range: 4V to 36V Operation
Very Low Dropout Operation: 99% Duty Cycle
Adjustable Soft-Start Current Ramping
Internal Current Foldback
Short-Circuit Shutdown Timer with Defeat Option
Overvoltage Soft-Latch Eliminates Nuisance Trips
Available in 28-Lead SSOP Package
An internal differential amplifier provides true remote
sensing of the regulated supply’s positive and negative
output terminals as required by high current applications.
The RUN/SS pin provides soft-start and a defeatable,
timed, latched short-circuit shutdown to shut down both
channels. Internal foldback current limit provides protection for the external synchronous MOSFETs in the event of
an output fault. OPTI-LOOP compensation allows the
transient response to be optimized over a wide range of
output capacitance and ESR values.
U
APPLICATIO S
■
■
■
Desktop Computers
Internet/Network Servers
Large Memory Arrays
DC Power Distribution Systems
, LTC and LT are registered trademarks of Linear Technology Corporation.
OPTI-LOOP is a trademark of Linear Technology Corporation.
U
■
TYPICAL APPLICATIO
10Ω
VIN
0.1µF
TG1
BOOST1
LTC1929 SW1
RUN/SS
BG1
0.47µF
D1
L1
1µH
0.002Ω
PGND
1000pF
SENSE1 +
ITH
SENSE1 –
100pF
TG2
SGND
BOOST2
VDIFFOUT
16k
BG2
EAIN
INTVCC
–
+
VOS
VOS +
SENSE2
VOUT
1.6V/40A
0.47µF
SW2
16k
D2
+
10k
VIN
5V TO 28V
10µF
35V
CERAMIC
×4
0.1µF
L2
1µH
0.002Ω
10µF
SENSE2 –
COUT: T510E108K004AS L1, L2: CEPH149-1ROMC
+
COUT
1000µF
4V
×2
1929 F01
Figure 1. High Current 2-Phase Step-Down Converter
1
LTC1929/LTC1929-PG
U
W W
W
ABSOLUTE
AXI U RATI GS
U
W
U
PACKAGE/ORDER I FOR ATIO
(Note 1)
ORDER PART
NUMBER
TOP VIEW
Input Supply Voltage (VIN).........................36V to – 0.3V
Topside Driver Voltages (BOOST1,2) .........42V to – 0.3V
Switch Voltage (SW1, 2) .............................36V to – 5 V
SENSE1+, SENSE2 +, SENSE1–,
SENSE2 – Voltages ........................ (1.1)INTVCC to – 0.3V
EAIN, VOS+, VOS–, EXTVCC, INTVCC,
RUN/SS, AMPMD Voltages ..........................7V to – 0.3V
Boosted Driver Voltage (BOOST-SW) ..........7V to – 0.3V
PLLFLTR, PLLIN, VDIFFOUT Voltages .... INTVCC to – 0.3V
ITH Voltage ................................................2.7V to – 0.3V
Peak Output Current <1µs(TGL1,2, BG1,2) ................ 3A
INTVCC RMS Output Current ................................ 50mA
Operating Ambient Temperature Range
LTC1929C .................................................. 0°C to 85°C
LTC1929I .............................................. – 40°C to 85°C
Junction Temperature (Note 2) ............................. 125°C
Storage Temperature Range ................. – 65°C to 150°C
Lead Temperature (Soldering, 10 sec).................. 300°C
RUN/SS
1
28 NC
SENSE1 +
2
27 TG1
SENSE1 –
3
26 SW1
EAIN
4
25 BOOST1
PLLFLTR
5
24 VIN
PLLIN
6
23 BG1
NC
7
22 EXTVCC
ITH
8
21 INTVCC
SGND
9
20 PGND
VDIFFOUT 10
VOS –
11
LTC1929CG
LTC1929CG-PG
LTC1929IG
LTC1929IG-PG
19 BG2
18 BOOST2
VOS + 12
17 SW2
SENSE2 – 13
16 TG2
SENSE2 + 14
15 AMPMD*
G PACKAGE
28-LEAD PLASTIC SSOP
*PGOOD ON LTC1929-PG
TJMAX = 125°C, θJA = 95°C/W
Consult factory for Military grade parts.
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VIN = 15V, VRUN/SS = 5V unless otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
●
0.792
0.800
0.808
V
●
62
65
75
75
88
85
mV
mV
–5
– 50
nA
0.05
– 0.1
0.5
– 0.5
%
%
0.002
0.02
%/V
Main Control Loop
VEAIN
Regulated Feedback Voltage
(Note 3); ITH Voltage = 1.2V
– = 5V
VSENSEMAX
Maximum Current Sense Threshold
VSENSE
VSENSE1, 2 = 5V, LTC1929 Only
IINEAIN
Feedback Current
(Note 3)
VLOADREG
Output Voltage Load Regulation
(Note 3)
Measured in Servo Loop; ITH Voltage = 0.7V
Measured in Servo Loop; ITH Voltage = 2V
●
●
VREFLNREG
Reference Voltage Line Regulation
VIN = 3.6V to 30V (Note 3)
VOVL
Output Overvoltage Threshold
Measured at VEAIN
0.84
0.86
0.88
V
UVLO
Undervoltage Lockout
VIN Ramping Down
3
3.5
4
V
gm
Transconductance Amplifier gm
ITH = 1.2V; Sink/Source 5µA; (Note 3)
gmOL
Transconductance Amplifier Gain
IQ
Input DC Supply Current
Normal Mode
Shutdown
IRUN/SS
Soft-Start Charge Current
VRUN/SS = 1.9V
– 0.5
–1.2
VRUN/SS
RUN/SS Pin ON Threshold
VRUN/SS Rising
1.0
1.5
1.9
V
VRUN/SSLO
RUN/SS Pin Latchoff Arming
VRUN/SS Rising from 3V
4.1
4.5
V
2
3
mmho
ITH = 1.2V; (gmxZL; No Ext Load); (Note 3)
1.5
V/mV
(Note 4)
EXTVCC Tied to VOUT; VOUT = 5V
VRUN/SS = 0V
470
20
40
µA
µA
µA
LTC1929/LTC1929-PG
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VIN = 15V, VRUN/SS = 5V unless otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
ISCL
RUN/SS Discharge Current
Soft Short Condition VEAIN = 0.5V;
VRUN/SS = 4.5V
0.5
2.0
4.0
µA
ISDLHO
Shutdown Latch Disable Current
VEAIN = 0.5V
1.6
5
µA
ISENSE
Total Sense Pins Source Current
Each Channel: VSENSE1 –, 2 – = VSENSE1+, 2 + = 0V
– 85
– 60
µA
DFMAX
Maximum Duty Factor
In Dropout
98
99.5
%
TG1, 2 tr
TG1, 2 tf
Top Gate Transition Time:
Rise Time
Fall Time
CLOAD = 3300pF
CLOAD = 3300pF
30
40
90
90
ns
ns
BG1, 2 tr
BG1, 2 tf
Bottom Gate Transition Time:
Rise Time
Fall Time
CLOAD = 3300pF
CLOAD = 3300pF
30
20
90
90
ns
ns
TG/BG t1D
Top Gate Off to Bottom Gate On Delay
Synchronous Switch-On Delay Time
CLOAD = 3300pF Each Driver
90
ns
BG/TG t2D
Bottom Gate Off to Top Gate On Delay
Top Switch-On Delay Time
CLOAD = 3300pF Each Driver
90
ns
Minimum On-Time
Tested with a Square Wave (Note 6)
180
ns
tON(MIN)
Internal VCC Regulator
VINTVCC
Internal VCC Voltage
6V < VIN < 30V; VEXTVCC = 4V
4.8
5.0
5.2
V
VLDO INT
INTVCC Load Regulation
ICC = 0 to 20mA; VEXTVCC = 4V
0.2
1.0
%
VLDO EXT
EXTVCC Voltage Drop
ICC = 20mA; VEXTVCC = 5V
120
240
mV
80
160
mV
VLDO EXT-PG
EXTVCC Voltage Drop
ICC = 20mA, VEXTVCC = 5V, LTC1929-PG
VEXTVCC
EXTVCC Switchover Voltage
ICC = 20mA, EXTVCC Ramping Positive
VLDOHYS
EXTVCC Switchover Hysteresis
ICC = 20mA, EXTVCC Ramping Negative
●
4.5
4.7
V
0.2
V
Oscillator and Phase-Locked Loop
fNOM
Nominal Frequency
VPLLFLTR = 1.2V
190
220
250
kHz
fLOW
Lowest Frequency
VPLLFLTR = 0V
120
140
160
kHz
fHIGH
Highest Frequency
VPLLFLTR ≥ 2.4V
280
310
360
kHz
RPLLIN
PLLIN Input Resistance
IPLLFLTR
Phase Detector Output Current
Sinking Capability
Sourcing Capability
RRELPHS
fPLLIN < fOSC
fPLLIN > fOSC
Controller 2-Controller 1 Phase
50
kΩ
– 15
15
µA
µA
180
Deg
PGOOD Output (LTC1929-PG Only)
VPGL
PGOOD Voltage Low
IPGOOD = 2mA
IPGOOD
PGOOD Leakage Current
VPGOOD = 5V
VPG
PGOOD Trip Level
VEAIN with Respect to Set Output Voltage
VEAIN Ramping Negative
VEAIN Ramping Positive
0.1
0.3
V
±1
µA
–6
6
–7.5
7.5
– 9.5
9.5
%
%
0.995
1
1.005
V/V
Differential Amplifier/Op Amp Gain Block (Note 5)
ADA
Gain
Differential Amp Mode
CMRRDA
Common Mode Rejection Ratio
Differential Amp Mode; 0V < VCM < 5V
RIN
Input Resistance
Differential Amp Mode; Measured at VOS + Input
VOS
Input Offset Voltage
Op Amp Mode; VCM = 2.5V; VDIFFOUT = 5V;
IDIFFOUT = 1mA (LTC1929 Only)
46
55
dB
80
kΩ
6
mV
3
LTC1929/LTC1929-PG
ELECTRICAL CHARACTERISTICS The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VIN = 15V, VRUN/SS = 5V unless otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
MIN
IB
Input Bias Current
Op Amp Mode (LTC1929 Only)
AOL
Open Loop DC Gain
Op Amp Mode; 0.7V ≤ VDIFFOUT < 10V
(LTC1929 Only)
VCM
Common Mode Input Voltage Range
Op Amp Mode (LTC1929 Only)
0
CMRROA
Common Mode Rejection Ratio
Op Amp Mode; 0V < VCM < 3V (LTC1929 Only)
70
90
dB
PSRROA
Power Supply Rejection Ratio
Op Amp Mode; 6V < VIN < 30V (LTC1929 Only)
70
90
dB
ICL
Maximum Output Current
Op Amp Mode; VDIFFOUT = 0V (LTC1929 Only)
10
35
mA
VO(MAX)
Maximum Output Voltage
Op Amp Mode; IDIFFOUT = 1mA (LTC1929 Only)
10
11
V
GBW
Gain-Bandwidth Product
Op Amp Mode; IDIFFOUT = 1mA (LTC1929 Only)
2
MHz
SR
Slew Rate
Op Amp Mode; RL = 2k (LTC1929 Only)
5
V/µs
Note 1: Absolute Maximum Ratings are those values beyond which the
life of a device may be impaired.
Note 2: TJ is calculated from the ambient temperature TA and power
dissipation PD according to the following formulas:
LTC1929CG: TJ = TA + (PD • 95°C/W)
Note 3: The LTC1929 is tested in a feedback loop that servos VITH to a
specified voltage and measures the resultant VEAIN.
Note 4: Dynamic supply current is higher due to the gate charge being
delivered at the switching frequency. See Applications Information.
TYP
MAX
30
200
5000
UNITS
nA
V/mV
3
V
Note 5: When the AMPMD pin is high (default for the LTC1929-PG), the
LTC1929 IC pins are connected directly to the internal op amp inputs.
When the AMPMD pin is low, internal MOSFET switches connect four
40k resistors around the op amp to create a standard unity-gain
differential amp.
Note 6: Minimum on-time condition corresponds to the on inductor
peak-to-peak ripple current ≥ 40% of IMAX (see minimum on-time
considerations in the Applications Information section).
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Efficiency vs Output Current
(Figure 13)
Efficiency vs Output Current
(Figure 13)
100
Efficiency vs VIN
(Figure 13)
100
100
VEXTVCC = 5V
IOUT = 20A
VEXTVCC = 5V
80
80
VIN = 8V
60
VIN = 12V
VIN = 20V
40
20
VOUT = 2V
VEXTVCC = 0V
FREQ = 200kHz
0
0.1
1
10
OUTPUT CURRENT (A)
100
1929 G01
4
VEXTVCC = 0V
EFFICIENCY (%)
EFFICIENCY (%)
EFFICIENCY (%)
VIN = 5V
60
40
20
0
0.1
VIN = 12V
VOUT = 2V
FREQ = 200kHz
90
VOUT = 2V
80
VOUT = 1.6V
70
60
50
1
10
OUTPUT CURRENT (A)
100
5
10
15
20
VIN (V)
1929 G02
1929 G03
LTC1929/LTC1929-PG
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Supply Current vs Input Voltage
and Mode
EXTVCC VOLTAGE DROP (mV)
800
SUPPLY CURRENT (µA)
5.05
250
VOUT = 5V
VEXTVCC = VOUT
600
ON
400
200
INTVCC AND EXTVCC SWITCH VOLTAGE (V)
1000
INTVCC and EXTVCC Switch
Voltage vs Temperature
EXTVCC Voltage Drop
200
LTC1929
150
LTC1929-PG
100
50
SHUTDOWN
0
0
5
20
15
10
25
INPUT VOLTAGE (V)
30
0
35
0
10
30
20
CURRENT (mA)
40
1929 G04
4.85
4.80
EXTVCC SWITCHOVER THRESHOLD
4.75
50
25
75
0
TEMPERATURE (°C)
100
125
1929 G06
Maximum Current Sense Threshold
vs Percent on Nominal Output
Voltage (Foldback)
Maximum Current Sense Threshold
vs Duty Factor
75
80
ILOAD = 1mA
70
60
4.8
4.7
50
VSENSE (mV)
4.9
VSENSE (mV)
INTVCC VOLTAGE (V)
4.90
4.70
– 50 – 25
50
5.0
25
4.6
50
40
30
20
4.5
10
0
4.4
0
5
20
15
25
10
INPUT VOLTAGE (V)
30
0
35
20
40
60
DUTY FACTOR (%)
80
Maximum Current Sense Threshold
vs VRUN/SS (Soft-Start)
80
0
100
50
100
0
25
75
PERCENT ON NOMINAL OUTPUT VOLTAGE (%)
1929 G08
1929 G07
1929 G09
Maximum Current Sense Threshold
vs Sense Common Mode Voltage
Current Sense Threshold
vs ITH Voltage
90
80
VSENSE(CM) = 1.6V
80
70
76
40
60
VSENSE (mV)
VSENSE (mV)
60
VSENSE (mV)
4.95
1929 G05
Internal 5V LDO Line Reg
5.1
INTVCC VOLTAGE
5.00
72
68
50
40
30
20
10
20
0
64
–10
–20
0
0
1
2
3
4
5
6
VRUN/SS (V)
1929 G10
60
0
1
3
4
2
COMMON MODE VOLTAGE (V)
5
1929 G11
–30
0
0.5
1
1.5
VITH (V)
2
2.5
1929 G12
5
LTC1929/LTC1929-PG
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Load Regulation
VITH vs VRUN/SS
2.5
VIN = 15V
FIGURE 1
SENSE Pins Total Source Current
100
VOSENSE = 0.7V
2.0
–0.2
50
ISENSE (µA)
–0.1
VITH (V)
NORMALIZED VOUT (%)
0.0
1.5
1.0
–0.3
0
–50
0.5
–0.4
0
0
1
3
2
LOAD CURRENT (A)
4
5
0
1
2
3
5
4
–100
2
0
VRUN/SS (V)
4
1629 G14
Maximum Current Sense
Threshold vs Temperature
1629 G15
RUN/SS Current vs Temperature
1.8
VSENSE– = 5V
1.6
RUN/SS CURRENT (µA)
VSENSE (mV)
78
76
74
72
1.4
1.2
1.0
0.8
0.6
0.4
0.2
70
–50
–25
50
25
0
75
TEMPERATURE (°C)
100
0
–50
125
–25
0
25
50
75
TEMPERATURE (°C)
1929 G16
100
125
1929 G17
Soft-Start (Figure 13)
Load Step (Figure 13)
VITH
1V/DIV
VOUT
50mV/DIV
VOUT
2V/DIV
20A
VRUN/SS
2V/DIV
IOUT
10A/DIV
0A
100ms/DIV
6
1929 G18
6
VSENSE COMMON MODE VOLTAGE (V)
1629 G13
80
6
20µs/DIV
1929 G19
LTC1929/LTC1929-PG
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Current SENSE Pin Input Current
vs Temperature
EXTVCC Switch Resistance
vs Temperature
10
35
350
VOUT = 5V
33
31
29
27
50
25
0
75
TEMPERATURE (°C)
100
125
8
6
4
VFREQSET = OPEN
200
VFREQSET = 0V
150
100
50
0
–50 –25
50
25
0
75
TEMPERATURE (°C)
100
125
0
– 50 – 25
50
25
75
0
TEMPERATURE (°C)
1929 G21
1929 G20
Undervoltage Lockout
vs Temperature
100
125
1929 G22
VRUN/SS Shutdown Latch
Thresholds vs Temperature
4.5
3.50
3.45
3.40
3.35
3.30
3.25
3.20
–50 –25
250
2
SHUTDOWN LATCH THRESHOLDS (V)
25
–50 –25
300
FREQUENCY (kHz)
EXTVCC SWITCH RESISTANCE (Ω)
VFREQSET = 5V
UNDERVOLTAGE LOCKOUT (V)
CURRENT SENSE INPUT CURRENT (µA)
Oscillator Frequency
vs Temperature
50
25
75
0
TEMPERATURE (°C)
100
125
1929 G23
LATCH ARMING
4.0
3.5
3.0
LATCHOFF
THRESHOLD
2.5
2.0
1.5
1.0
0.5
0
–50
–25
0
25
50
75
TEMPERATURE (°C)
100
125
1929 G24
7
LTC1929/LTC1929-PG
U
U
U
PI FU CTIO S
RUN/SS (Pin 1): Combination of Soft-Start, Run Control
Input and Short-Circuit Detection Timer. A capacitor to
ground at this pin sets the ramp time to full current output.
Forcing this pin below 0.8V causes the IC to shut down all
internal circuitry. All functions are disabled in shutdown.
SENSE1+, SENSE2+ (Pins 2,14): The (+) Input to the
Differential Current Comparators. The ITH pin voltage and
built-in offsets between SENSE– and SENSE+ pins in
conjunction with RSENSE set the current trip threshold.
SENSE1–, SENSE2– (Pins 3, 13): The (–) Input to the
Differential Current Comparators.
EAIN (Pin 4): Input to the Error Amplifier that compares
the feedback voltage to the internal 0.8V reference voltage.
This pin is normally connected to a resistive divider from
the output of the differential amplifier (DIFFOUT).
PLLFLTR (Pin 5): The Phase-Locked Loop’s Low Pass
Filter is tied to this pin. Alternatively, this pin can be driven
with an AC or DC voltage source to vary the frequency of
the internal oscillator.
PLLIN (Pin 6): External Synchronization Input to Phase
Detector. This pin is internally terminated to SGND with
50kΩ. The phase-locked loop will force the rising top gate
signal of controller 1 to be synchronized with the rising
edge of the PLLIN signal.
NC (Pins 7, 28): Not connected.
ITH (Pin 8): Error Amplifier Output and Switching Regulator Compensation Point. Both current comparator’s thresholds increase with this control voltage. The normal voltage
range of this pin is from 0V to 2.4V
SGND (Pin 9): Signal Ground, common to both controllers, must be routed separately from the input switched
current ground path to the common (–) terminal(s) of the
COUT capacitor(s).
VDIFFOUT (Pin 10): Output of a Differential Amplifier that
provides true remote output voltage sensing. This pin
normally drives an external resistive divider that sets the
output voltage.
VOS–, VOS+ (Pins 11, 12): Inputs to an Operational
Amplifier. Internal precision resistors capable of being
electronically switched in or out can configure it as a
8
differential amplifier (default for the LTC1929-PG) or an
uncommitted Op Amp.
AMPMD (Pin 15): (LTC1929 Only) This Logic Input pin
controls the connections of internal precision resistors
that configure the operational amplifier as a unity-gain
differential amplifier.
PGOOD (Pin 15): (LTC1929-PG Only) Open-Drain Logic
Output. PGOOD is pulled to ground when the voltage on
the EAIN pin is not within ±7.5% of its set point.
TG2, TG1 (Pins 16, 27): High Current Gate Drives for Top
N-Channel MOSFETS. These are the outputs of floating
drivers with a voltage swing equal to INTVCC superimposed on the switch node voltage SW.
SW2, SW1 (Pins 17, 26): Switch Node Connections to
Inductors. Voltage swing at these pins is from a Schottky
diode (external) voltage drop below ground to VIN.
BOOST2, BOOST1 (Pins 18, 25): Bootstrapped Supplies
to the Topside Floating Drivers. Capacitors are connected
between the Boost and Switch pins, and Schottky diodes
are tied between the Boost and INTVCC pins.
BG2, BG1 (Pins 19, 23): Voltage Swing High Current Gate
Drives for Bottom Synchronous N-Channel MOSFETS.
Voltage swing at these pins is from ground to INTVCC.
PGND (Pin 20): Driver Power Ground. Connects to sources
of bottom N-channel MOSFETS and the (–) terminals of
CIN.
INTVCC (Pin 21): Output of the Internal 5V Linear Low
Dropout Regulator and the EXTVCC Switch. The driver and
control circuits are powered from this voltage source.
Decouple to power ground with a 1µF ceramic capacitor
placed directly adjacent to the IC and minimum of 4.7µF
additional tantalum or other low ESR capacitor.
EXTVCC (Pin 22): External Power Input to an Internal
Switch . This switch closes and supplies INTVCC, bypassing the internal low dropout regulator whenever EXTVCC is
higher than 4.7V. See EXTVCC Connection in the Applications Information section. Do not exceed 7V on this pin
and ensure VEXTVCC ≤ VIN.
VIN (Pin 24): Main Supply Pin. Should be closely decoupled
to the IC’s signal ground pin.
LTC1929/LTC1929-PG
W
FU CTIO AL DIAGRA
U
U
LTC1929-PG OPTIONAL PGOOD HOOKUP
DIFFOUT
PGOOD
–
0.86V
+
VOS –
EAIN
A1
–
–
VOS +
+
+
0.74V
VIN
INTVCC
PLLIN
PHASE DET
FIN
DUPLICATE FOR SECOND
CONTROLLER CHANNEL
50k
DB
BOOST
PLLFLTR
RLP
DROP
OUT
DET
CLK1
OSCILLATOR
CLP
CLK2
S
Q
R
Q
CB
TG
TOP
+
CIN
BOT
SW
FORCE BOT
SWITCH
LOGIC
INTVCC
BOT
BG
PGND
LTC1929 ONLY
VOS
–
SHDN
A1
VOS +
–
I1
+
INTVCC
–
+
–
+
L
+
30k SENSE
4(VFB)
–
30k SENSE
SLOPE
COMP
0V POSITION
DIFFOUT
RSENSE
COUT
+
AMPMD
45k
45k
VOUT
2.4V
0.8V
VIN
–
EA
+
VREF
EAIN
R1
0.80V
R2
OV
VIN
+
4.7V
EXTVCC
+
–
5V
LDO
REG
–
VIN
INTVCC
+
6V
SGND
INTERNAL
SUPPLY
0.86V
ITH
CC
1.2µA
SHDN
5V
VFB
4(VFB)
RUN
SOFTSTART
RC
RUN/SS
CSS
1929 FBD
9
LTC1929/LTC1929-PG
U
OPERATIO (Refer to Functional Diagram)
Main Control Loop
Low Current Operation
The LTC1929 uses a constant frequency, current mode
step-down architecture with inherent current sharing.
During normal operation, the top MOSFET is turned on
each cycle when the oscillator sets the RS latch, and
turned off when the main current comparator, I1, resets
the RS latch. The peak inductor current at which I1 resets
the RS latch is controlled by the voltage on the ITH pin,
which is the output of the error amplifier EA. The differential amplifier, A1, produces a signal equal to the differential
voltage sensed across the output capacitor but re-references it to the internal signal ground (SGND) reference.
The EAIN pin receives a portion of this voltage feedback
signal at the DIFFOUT pin which is compared to the
internal reference voltage by the EA. When the load current
increases, it causes a slight decrease in the EAIN pin
voltage relative to the 0.8V reference, which in turn causes
the ITH voltage to increase until the average inductor
current matches the new load current. After the top
MOSFET has turned off, the bottom MOSFET is turned on
for the rest of the period.
The LTC1929 operates in a continuous, PWM control
mode. The resulting operation at low output currents
optimizes transient response at the expense of substantial
negative inductor current during the latter part of the
period. The level of ripple current is determined by the
inductor value, input voltage, output voltage, and frequency of operation.
The top MOSFET drivers are biased from floating bootstrap capacitor CB, which normally is recharged during
each off cycle through an external Schottky diode. When
VIN decreases to a voltage close to VOUT, however, the loop
may enter dropout and attempt to turn on the top MOSFET
continuously. A dropout detector detects this condition
and forces the top MOSFET to turn off for about 400ns
every 10th cycle to recharge the bootstrap capacitor.
The main control loop is shut down by pulling Pin 1 (RUN/
SS) low. Releasing RUN/SS allows an internal 1.2µA
current source to charge soft-start capacitor CSS. When
CSS reaches 1.5V, the main control loop is enabled with the
ITH voltage clamped at approximately 30% of its maximum
value. As CSS continues to charge, ITH is gradually released allowing normal operation to resume. When the
RUN/SS pin is low, all LTC1929 functions are shut down.
If VOUT has not reached 70% of its nominal value when CSS
has charged to 4.1V, an overcurrent latchoff can be
invoked as described in the Applications Information
section.
10
Frequency Synchronization
The phase-locked loop allows the internal oscillator to be
synchronized to an external source via the PLLIN pin. The
output of the phase detector at the PLLFLTR pin is also the
DC frequency control input of the oscillator that operates
over a 140kHz to 310kHz range corresponding to a DC
voltage input from 0V to 2.4V. When locked, the PLL aligns
the turn on of the top MOSFET to the rising edge of the
synchronizing signal. When PLLIN is left open, the PLLFLTR
pin goes low, forcing the oscillator to minimum frequency.
Input capacitance ESR requirements and efficiency losses
are substantially reduced because the peak current drawn
from the input capacitor is effectively divided by two and
power loss is proportional to the RMS current squared. A
two stage, single output voltage implementation can reduce input path power loss by 75% and radically reduce
the required RMS current rating of the input capacitor(s).
INTVCC/EXTVCC Power
Power for the top and bottom MOSFET drivers and most
of the IC circuitry is derived from INTVCC. When the
EXTVCC pin is left open, an internal 5V low dropout
regulator supplies INTVCC power. If the EXTVCC pin is
taken above 4.7V, the 5V regulator is turned off and an
internal switch is turned on connecting EXTVCC to INTVCC.
This allows the INTVCC power to be derived from a high
efficiency external source such as the output of the regulator itself or a secondary winding, as described in the
Applications Information section. An external Schottky
diode can be used to minimize the voltage drop from
EXTVCC to INTVCC in applications requiring greater than
the specified INTVCC current. Voltages up to 7V can be
applied to EXTVCC for additional gate drive capability.
LTC1929/LTC1929-PG
U
OPERATIO
(Refer to Functional Diagram)
Differential Amplifier
This amplifier provides true differential output voltage
sensing. Sensing both VOUT + and VOUT – benefits regulation in high current applications and/or applications having electrical interconnection losses. The AMPMD pin
(LTC1929 only) allows selection of internal, precision feedback resistors for high common mode rejection differencing
applications, or direct access to the actual amplifier inputs
without these internal feedback resistors for other applications. The AMPMD pin is grounded to connect the internal
precision resistors in a unity-gain differencing application
(default for the LTC1929-PG), or tied to the INTVCC pin to
bypass the internal resistors and make the amplifier inputs
directly available. The amplifier is a unity-gain stable, 2MHz
gain-bandwidth, >120dB open-loop gain design. The amplifier has an output slew rate of 5V/µs and is capable of
driving capacitive loads with an output RMS current typically up to 25mA. The amplifier is not capable of sinking
current and therefore must be resistively loaded to do so.
Power Good (PGOOD) Pin (LTC1929-PG Only)
The PGOOD pin is connected to an open drain of a
MOSFET. The MOSFET turns on and pulls the pin low when
the output is not within ±7.5% of its nominal output level
as determined by its resistive feedback divider. When the
output meets the ±7.5% requirement, the MOSFET is
turned off within 10µs and the pin is allowed to be pulled
up by an external source.
Short-Circuit Detection
The RUN/SS capacitor is used initially to limit the inrush
current from the input power source. Once the controllers
have been given time, as determined by the capacitor on
the RUN/SS pin, to charge up the output capacitors and
provide full load current, the RUN/SS capacitor is then
used as a short-circuit timeout circuit. If the output voltage
falls to less than 70% of its nominal output voltage the
RUN/SS capacitor begins discharging assuming that the
output is in a severe overcurrent and/or short-circuit
condition. If the condition lasts for a long enough period
as determined by the size of the RUN/SS capacitor, the
controller will be shut down until the RUN/SS pin voltage
is recycled. This built-in latchoff can be overidden by
providing a current >5µA at a compliance of 5V to the
RUN/SS pin. This current shortens the soft-start period
but also prevents net discharge of the RUN/SS capacitor
during a severe overcurrent and/or short-circuit condition. Foldback current limiting is activated when the output
voltage falls below 70% of its nominal level whether or not
the short-circuit latchoff circuit is enabled.
U
W
U
U
APPLICATIO S I FOR ATIO
The basic LTC1929 application circuit is shown in Figure␣ 1
on the first page. External component selection is driven
by the load requirement, and begins with the selection of
RSENSE1, 2. Once RSENSE1, 2 are known, L1 and L2 can be
chosen. Next, the power MOSFETs and D1 and D2 are
selected. The operating frequency and the inductor are
chosen based mainly on the amount of ripple current.
Finally, CIN is selected for its ability to handle the input
ripple current (that PolyPhaseTM operation minimizes) and
COUT is chosen with low enough ESR to meet the output
ripple voltage and load step specifications (also minimized
with PolyPhase). Current mode architecture provides inherent current sharing between output stages. The circuit
shown in Figure␣ 1 can be configured for operation up to an
input voltage of 28V (limited by the external MOSFETs).
RSENSE Selection For Output Current
RSENSE1, 2 are chosen based on the required output
current. The LTC1929 current comparator has a maximum threshold of 75mV/RSENSE and an input common
mode range of SGND to 1.1( INTVCC). The current comparator threshold sets the peak inductor current, yielding
a maximum average output current IMAX equal to the peak
value less half the peak-to-peak ripple current, ∆IL.
Allowing a margin for variations in the LTC1929 and
external component values yields:
RSENSE = 2(50mV/IMAX)
PolyPhase is a trademark of Linear Technology Corporation.
11
LTC1929/LTC1929-PG
U
W
U
U
APPLICATIO S I FOR ATIO
When using the controller in very low dropout conditions,
the maximum output current level will be reduced due to
internal compensation required to meet stability criterion
for buck regulators operating at greater than 50% duty
factor. A curve is provided to estimate this reduction in
peak output current level depending upon the operating
duty factor.
Operating Frequency
The LTC1929 uses a constant frequency, phase-lockable
architecture with the frequency determined by an internal
capacitor. This capacitor is charged by a fixed current plus
an additional current which is proportional to the voltage
applied to the PLLFLTR pin. Refer to Phase-Locked Loop
and Frequency Synchronization in the Applications Information section for additional information.
A graph for the voltage applied to the PLLFLTR pin vs
frequency is given in Figure␣ 2. As the operating frequency
is increased the gate charge losses will be higher, reducing
efficiency (see Efficiency Considerations). The maximum
switching frequency is approximately 310kHz.
PLLFLTR PIN VOLTAGE (V)
2.5
2.0
1.5
1.0
MOSFET gate charge and transition losses. In addition to
this basic tradeoff, the effect of inductor value on ripple
current and low current operation must also be considered.
The PolyPhase approach reduces both input and output
ripple currents while optimizing individual output stages to
run at a lower fundamental frequency, enhancing efficiency.
The inductor value has a direct effect on ripple current. The
inductor ripple current ∆IL per individual section, N,
decreases with higher inductance or frequency and increases with higher VIN or VOUT:
∆IL =
VOUT  VOUT 
 1−

fL 
VIN 
where f is the individual output stage operating frequency.
In a 2-phase converter, the net ripple current seen by the
output capacitor is much smaller than the individual
inductor ripple currents due to the ripple cancellation. The
details on how to calculate the net output ripple current
can be found in Application Note 77.
Figure 3 shows the net ripple current seen by the output
capacitors for the 1- and 2-phase configurations. The
output ripple current is plotted for a fixed output voltage as
the duty factor is varied between 10% and 90% on the
x-axis. The output ripple current is normalized against the
inductor ripple current at zero duty factor. The graph can
be used in place of tedious calculations, simplifying the
design process.
0.5
1.0
1-PHASE
2-PHASE
0.9
0
120
170
220
270
OPERATING FREQUENCY (kHz)
0.8
320
0.7
0.6
VO/fL
Figure 2. Operating Frequency vs VPLLFLTR
∆IO(P-P)
1929 F02
0.5
0.4
0.3
Inductor Value Calculation and Output Ripple Current
The operating frequency and inductor selection are interrelated in that higher operating frequencies allow the use
of smaller inductor and capacitor values. So why would
anyone ever choose to operate at lower frequencies with
larger components? The answer is efficiency. A higher
frequency generally results in lower efficiency because of
12
0.2
0.1
0
0.1
0.2
0.3 0.4 0.5 0.6 0.7
DUTY FACTOR (VOUT/VIN)
0.8
0.9
1929 F03
Figure 3. Normalized Output Ripple Current
vs Duty Factor [IRMS ≈ 0.3 (∆IO(P–P))]
LTC1929/LTC1929-PG
U
W
U
U
APPLICATIO S I FOR ATIO
Accepting larger values of ∆IL allows the use of low
inductances, but can result in higher output voltage ripple.
A reasonable starting point for setting ripple current is ∆IL
= 0.4(IOUT)/2, where IOUT is the total load current. Remember, the maximum ∆IL occurs at the maximum input
voltage. The individual inductor ripple currents are determined by the inductor, input and output voltages.
EXTVCC Pin Connection). Consequently, logic-level threshold MOSFETs must be used in most applications. The only
exception is if low input voltage is expected (VIN < 5V);
then, sublogic-level threshold MOSFETs (VGS(TH) < 3V)
should be used. Pay close attention to the BVDSS specification for the MOSFETs as well; most of the logic-level
MOSFETs are limited to 30V or less.
Inductor Core Selection
Selection criteria for the power MOSFETs include the “ON”
resistance RDS(ON), reverse transfer capacitance CRSS,
input voltage, and maximum output current. When the
LTC1929 is operating in continuous mode the duty factors
for the top and bottom MOSFETs of each output stage are
given by:
Once the values for L1 and L2 are known, the type of
inductor must be selected. High efficiency converters
generally cannot afford the core loss found in low cost
powdered iron cores, forcing the use of more expensive
ferrite, molypermalloy, or Kool Mµ® cores. Actual core
loss is independent of core size for a fixed inductor value,
but it is very dependent on inductance selected. As inductance increases, core losses go down. Unfortunately,
increased inductance requires more turns of wire and
therefore copper losses will increase.
Ferrite designs have very low core loss and are preferred
at high switching frequencies, so design goals can concentrate on copper loss and preventing saturation. Ferrite
core material saturates “hard,” which means that inductance collapses abruptly when the peak design current is
exceeded. This results in an abrupt increase in inductor
ripple current and consequent output voltage ripple. Do
not allow the core to saturate!
Molypermalloy (from Magnetics, Inc.) is a very good, low
loss core material for toroids, but it is more expensive than
ferrite. A reasonable compromise from the same manufacturer is Kool Mµ. Toroids are very space efficient,
especially when you can use several layers of wire. Because they lack a bobbin, mounting is more difficult.
However, designs for surface mount are available which
do not increase the height significantly.
Power MOSFET, D1 and D2 Selection
Two external power MOSFETs must be selected for each
output stage with the LTC1929: One N-channel MOSFET
for the top (main) switch, and one N-channel MOSFET for
the bottom (synchronous) switch.
The peak-to-peak drive levels are set by the INTVCC voltage. This voltage is typically 5V during start-up (see
Main Switch Duty Cycle =
VOUT
VIN
V –V 
Synchronous Switch Duty Cycle =  IN OUT 


VIN
The MOSFET power dissipations at maximum output
current are given by:
2
I

V
PMAIN = OUT  MAX  1 + δ RDS(ON) +
VIN  2 

2 I
k VIN  MAX  CRSS f
 2 
( )
( )
(
)( )
2
I

V –V
PSYNC = IN OUT  MAX  1 + δ RDS(ON)
VIN
 2 
( )
where δ is the temperature dependency of RDS(ON) and k
is a constant inversely related to the gate drive current.
Both MOSFETs have I2R losses but the topside N-channel
equation includes an additional term for transition losses,
which peak at the highest input voltage. For VIN < 20V the
high current efficiency generally improves with larger
MOSFETs, while for VIN > 20V the transition losses rapidly
increase to the point that the use of a higher RDS(ON) device
with lower CRSS actual provides higher efficiency. The
Kool Mµ is a registered trademark of Magnetics, Inc.
13
LTC1929/LTC1929-PG
U
W
U
U
APPLICATIO S I FOR ATIO
0.5
DC LOAD CURRENT
The term (1 + δ) is generally given for a MOSFET in the
form of a normalized RDS(ON) vs. Temperature curve, but
δ = 0.005/°C can be used as an approximation for low
voltage MOSFETs. CRSS is usually specified in the MOSFET characteristics. The constant k = 1.7 can be used to
estimate the contributions of the two terms in the main
switch dissipation equation.
0.6
RMS INPUT RIPPLE CURRNET
synchronous MOSFET losses are greatest at high input
voltage when the top switch duty factor is low or during a
short-circuit when the synchronous switch is on close to
100% of the period.
0.4
1-PHASE
2-PHASE
0.3
0.2
0.1
0
0.1
0.2
0.3 0.4 0.5 0.6 0.7
DUTY FACTOR (VOUT/VIN)
0.8
0.9
1929 F04
The Schottky diodes, D1 and D2 shown in Figure 1 conduct
during the dead-time between the conduction of the two
large power MOSFETs. This helps prevent the body diode
of the bottom MOSFET from turning on, storing charge
during the dead-time, and requiring a reverse recovery
period which would reduce efficiency. A 1A to 3A (depending on output current) Schottky diode is generally a good
compromise for both regions of operation due to the
relatively small average current. Larger diodes result in
additional transition losses due to their larger junction
capacitance.
CIN and COUT Selection
In continuous mode, the source current of each top
N-channel MOSFET is a square wave of duty cycle VOUT/
VIN. A low ESR input capacitor sized for the maximum
RMS current must be used. The details of a close form
equation can be found in Application Note 77. Figure 4
shows the input capacitor ripple current for a 2-phase
configuration with the output voltage fixed and input
voltage varied. The input ripple current is normalized
against the DC output current. The graph can be used in
place of tedious calculations. The minimum input ripple
current can be achieved when the input voltage is twice the
output voltage. The minimum is not quite zero due to
inductor ripple current.
In the graph of Figure 4, the local maximum input RMS
capacitor currents are reached when:
VOUT 2k − 1
=
VIN
4
14
where k = 1, 2.
Figure 4. Normalized RMS Input Ripple Current
vs Duty Factor for 1 and 2 Output Stages
These worst-case conditions are commonly used for design because even significant deviations do not offer much
relief. Note that capacitor manufacturer’s ripple current
ratings are often based on only 2000 hours of life. This
makes it advisable to further derate the capacitor, or to
choose a capacitor rated at a higher temperature than
required. Several capacitors may also be paralleled to meet
size or height requirements in the design. Always consult
the capacitor manufacturer if there is any question.
It is important to note that the efficiency loss is proportional to the input RMS current squared and therefore a
2-stage implementation results in 75% less power loss
when compared to a single phase design. Battery/input
protection fuse resistance (if used), PC board trace and
connector resistance losses are also reduced by the reduction of the input ripple current in a 2-phase system. The
required amount of input capacitance is further reduced by
the factor, 2, due to the effective increase in the frequency
of the current pulses.
The selection of COUT is driven by the required effective
series resistance (ESR). Typically once the ESR requirement has been met, the RMS current rating generally far
exceeds the IRIPPLE(P-P) requirements. The steady state
output ripple (∆VOUT) is determined by:

1 
∆VOUT ≈ ∆IRIPPLE  ESR +

16 fCOUT 

LTC1929/LTC1929-PG
U
W
U
U
APPLICATIO S I FOR ATIO
Where f = operating frequency of each stage, COUT =
output capacitance and ∆IRIPPLE = combined inductor
ripple currents.
The output ripple varies with input voltage since ∆IL is a
function of input voltage. The output ripple will be less than
50mV at max VIN with ∆IL = 0.4IOUT(MAX)/2 assuming:
COUT required ESR < 4(RSENSE) and
COUT > 1/(16f)(RSENSE)
The emergence of very low ESR capacitors in small,
surface mount packages makes very physically small
implementations possible. The ability to externally compensate the switching regulator loop using the ITH pin
(OPTI-LOOP compensation) allows a much wider selection of output capacitor types. OPTI-LOOP compensation
effectively removes constraints on output capacitor ESR.
The impedance characteristics of each capacitor type are
significantly different than an ideal capacitor and therefore
require accurate modeling or bench evaluation during
design.
Manufacturers such as Nichicon, United Chemicon and
Sanyo should be considered for high performance throughhole capacitors. The OS-CON semiconductor dielectric
capacitor available from Sanyo and the Panasonic SP
surface mount types have the lowest (ESR)(size) product
of any aluminum electrolytic at a somewhat higher price.
An additional ceramic capacitor in parallel with OS-CON
type capacitors is recommended to reduce the inductance
effects.
In surface mount applications, multiple capacitors may
have to be paralleled to meet the ESR or RMS current
handling requirements of the application. Aluminum electrolytic and dry tantalum capacitors are both available in
surface mount configurations. New special polymer surface mount capacitors offer very low ESR also but have
much lower capacitive density per unit volume. In the case
of tantalum, it is critical that the capacitors are surge tested
for use in switching power supplies. Several excellent
choices are the AVX TPS, AVX TPSV or the KEMET T510
series of surface mount tantalums, available in case heights
ranging from 2mm to 4mm. Other capacitor types include
Sanyo OS-CON, Nichicon PL series and Sprague 595D
series. Consult the manufacturer for other specific recommendations. A combination of capacitors will often result
in maximizing performance and minimizing overall cost
and size.
INTVCC Regulator
An internal P-channel low dropout regulator produces 5V
at the INTVCC pin from the VIN supply pin. The INTVCC
regulator powers the drivers and internal circuitry of the
LTC1929. The INTVCC pin regulator can supply up to 50mA
peak and must be bypassed to power ground with a
minimum of 4.7µF tantalum or electrolytic capacitor. An
additional 1µF ceramic capacitor placed very close to the
IC is recommended due to the extremely high instantaneous currents required by the MOSFET gate drivers.
High input voltage applications in which large MOSFETs
are being driven at high frequencies may cause the maximum junction temperature rating for the LTC1929 to be
exceeded. The supply current is dominated by the gate
charge supply current, in addition to the current drawn
from the differential amplifier output. The gate charge is
dependent on operating frequency as discussed in the
Efficiency Considerations section. The supply current can
either be supplied by the internal 5V regulator or via the
EXTVCC pin. When the voltage applied to the EXTVCC pin
is less than 4.7V, all of the INTVCC load current is supplied
by the internal 5V linear regulator. Power dissipation for
the IC is higher in this case by (IIN)(VIN – INTVCC) and
efficiency is lowered. The junction temperature can be
estimated by using the equations given in Note 1 of the
Electrical Characteristics. For example, the LTC1929 VIN
current is limited to less than 24mA from a 24V supply:
TJ = 70°C + (24mA)(24V)(95°C/W) = 125°C
Use of the EXTVCC pin reduces the junction temperature
to:
TJ = 70°C + (24mA)(5V)(95°C/W) = 81.4°C
The input supply current should be measured while the
controller is operating in continuous mode at maximum
VIN and the power dissipation calculated in order to prevent the maximum junction temperature from being
exceeded.
15
LTC1929/LTC1929-PG
U
W
U
U
APPLICATIO S I FOR ATIO
EXTVCC Connection
The LTC1929 contains an internal P-channel MOSFET
switch connected between the EXTVCC and INTVCC pins.
When the voltage applied to EXTVCC rises above 4.7V, the
internal regulator is turned off and the switch closes,
connecting the EXTVCC pin to the INTVCC pin thereby
supplying internal and MOSFET gate driving power. The
switch remains closed as long as the voltage applied to
EXTVCC remains above 4.5V. This allows the MOSFET
driver and control power to be derived from the output
during normal operation (4.7V < VEXTVCC < 7V) and from
the internal regulator when the output is out of regulation
(start-up, short-circuit). Do not apply greater than 7V to
the EXTVCC pin and ensure that EXTVCC < VIN + 0.3V when
using the application circuits shown. If an external voltage
source is applied to the EXTVCC pin when the VIN supply is
not present, a diode can be placed in series with the
LTC1929’s VIN pin and a Schottky diode between the
EXTVCC and the VIN pin, to prevent current from backfeeding
VIN.
Significant efficiency gains can be realized by powering
INTVCC from the output, since the VIN current resulting
from the driver and control currents will be scaled by the
ratio: (Duty Factor)/(Efficiency). For 5V regulators this
means connecting the EXTVCC pin directly to VOUT. However, for 3.3V and other lower voltage regulators, additional circuitry is required to derive INTVCC power from the
output.
The following list summarizes the four possible connections for EXTVCC:
OPTIONAL EXTVCC CONNECTION
5V < VSEC < 7V
+
CIN
1. EXTVCC left open (or grounded). This will cause INTVCC
to be powered from the internal 5V regulator resulting in
a significant efficiency penalty at high input voltages.
2. EXTVCC connected directly to VOUT. This is the normal
connection for a 5V regulator and provides the highest
efficiency.
3. EXTVCC connected to an external supply. If an external
supply is available in the 5V to 7V range, it may be used to
power EXTVCC providing it is compatible with the MOSFET
gate drive requirements.
4. EXTVCC connected to an output-derived boost network.
For 3.3V and other low voltage regulators, efficiency gains
can still be realized by connecting EXTVCC to an outputderived voltage which has been boosted to greater than
4.7V but less than 7V. This can be done with either the
inductive boost winding as shown in Figure 5a or the
capacitive charge pump shown in Figure 5b. The charge
pump has the advantage of simple magnetics.
Topside MOSFET Driver Supply (CB,DB) (Refer to
Functional Diagram)
External bootstrap capacitors CB1 and CB2 connected to
the BOOST1 and BOOST2 pins supply the gate drive
voltages for the topside MOSFETs. Capacitor CB in the
Functional Diagram is charged though diode DB from
INTVCC when the SW pin is low. When the topside MOSFET
turns on, the driver places the CB voltage across the gatesource of the desired MOSFET. This enhances the MOSFET
and turns on the topside switch. The switch node voltage,
+
VIN
VIN
1N4148
TG1
EXTVCC
+
1µF
VOUT
T1
BAT85
N-CH
LTC1929
VN2222LL
BAT85
EXTVCC
SW1
VOUT
L1
+
+
COUT
BG1
0.22µF
RSENSE
RSENSE
SW1
BAT85
TG1
VSEC
N-CH
LTC1929
+
VIN
CIN
VIN
COUT
BG1
N-CH
N-CH
PGND
PGND
1929 F05b
1929 F05a
Figure 5a. Secondary Output Loop with EXTVCC Connection
16
Figure 5b. Capacitive Charge Pump for EXTVCC
LTC1929/LTC1929-PG
U
W
U
U
APPLICATIO S I FOR ATIO
SW, rises to VIN and the BOOST pin rises to VIN + VINTVCC.
The value of the boost capacitor CB needs to be 30 to 100
times that of the total input capacitance of the topside
MOSFET(s). The reverse breakdown of DB must be greater
than VIN(MAX).
The final arbiter when defining the best gate drive amplitude level will be the input supply current. If a change is
made that decreases input current, the efficiency has
improved. If the input current does not change then the
efficiency has not changed either.
Output Voltage
The LTC1929 has a true remote voltage sense capability.
The sensing connections should be returned from the load
back to the differential amplifier’s inputs through a common, tightly coupled pair of PC traces. The differential
amplifier rejects common mode signals capacitively or
inductively radiated into the feedback PC traces as well as
ground loop disturbances. The differential amplifier output signal is divided down and compared with the internal
precision 0.8V voltage reference by the error amplifier.
The differential amplifier can be used in either of two
configurations according to the voltage applied to the
AMPMD pin (LTC1929 only). The first configuration, with
the connections illustrated in the Functional Diagram,
utilizes a set of internal precision resistors to enable
precision instrumentation-type measurement of the output voltage. This configuration is activated when the
AMPMD pin is tied to ground and is the default for the
LTC1929-PG. When the AMPMD pin is tied to INTVCC, the
resistors are disconnected and the amplifier inputs are
made directly available. The amplifier can then be used as
a general purpose op amp. The amplifier has a 0V to 3V
common mode input range limitation due to the internal
switching of its inputs. The output is an NPN emitter
follower without any internal pull-down current. A DC
resistive load to ground is required in order to sink current.
The output will swing from 0V to 10V (VIN ≥ VDIFFOUT + 2V).
Soft-Start/Run Function
The RUN/SS pin provides three functions: 1) Run/Shutdown, 2) soft-start and 3) a defeatable short-circuit latchoff
timer. Soft-start reduces the input power sources’ surge
currents by gradually increasing the controller’s current
limit ITH(MAX). The latchoff timer prevents very short,
extreme load transients from tripping the overcurrent
latch. A small pull-up current (>5µA) supplied to the RUN/
SS pin will prevent the overcurrent latch from operating.
The following explanation describes how the functions
operate.
An internal 1.2µA current source charges up the CSS
capacitor. When the voltage on RUN/SS reaches 1.5V, the
controller is permitted to start operating. As the voltage on
RUN/SS increases from 1.5V to 3.0V, the internal current
limit is increased from 25mV/RSENSE to 75mV/RSENSE.
The output current limit ramps up slowly, taking an
additional 1.4s/µF to reach full current. The output current
thus ramps up slowly, reducing the starting surge current
required from the input power supply. If RUN/SS has been
pulled all the way to ground there is a delay before starting
of approximately:
tDELAY =
(
)
1.5V
CSS = 1.25s / µF CSS
1.2µA
The time for the output current to ramp up is then:
tIRAMP =
(
)
3V − 1.5V
CSS = 1.25s / µF CSS
1.2µA
By pulling both RUN/SS controller pins below 0.8V the
LTC1929 is put into low current shutdown (IQ < 40µA). The
RUN/SS pins can be driven directly from logic as shown in
Figure 6. Diode D1 in Figure 6 reduces the start delay but
allows CSS to ramp up slowly providing the soft-start
function. The RUN/SS pin has an internal 6V zener clamp
(see Functional Diagram).
Fault Conditions: Overcurrent Latchoff
The RUN/SS pin also provides the ability to latch off the
controllers when an overcurrent condition is detected.
The RUN/SS capacitor, CSS, is used initially to limit the
inrush current of both controllers. After the controllers
have been started and been given adequate time to charge
up the output capacitors and provide full load current, the
RUN/SS capacitor is used for a short-circuit timer. If the
output voltage falls to less than 70% of its nominal value,
17
LTC1929/LTC1929-PG
U
W
U
U
APPLICATIO S I FOR ATIO
after CSS reaches 4.1V, CSS begins discharging on the
assumption that the output is in an overcurrent condition.
If the condition lasts for a long enough period as determined by the size of CSS, the controller will be shut down
until the RUN/SS pin voltage is recycled. If the overload
occurs during start-up, the time can be approximated by:
If the overload occurs after start-up the voltage on the
RUN/SS capacitor will continue charging and will provide
additional time before latching off:
tLO2 ≈ (CSS • 3V)/(1.2µA) = 2.5 • 106 (CSS)
This built-in overcurrent latchoff can be overridden by
providing a pull-up resistor, RSS, to the RUN/SS pin as
shown in Figure 6. This resistance shortens the soft-start
period and prevents the discharge of the RUN/SS capacitor during a severe overcurrent and/or short-circuit condition. When deriving the 5µA current from VIN as in the
figure, current latchoff is always defeated. The diode
connecting of this pull-up resistor to INTVCC, as in
Figure␣ 6, eliminates any extra supply current during shutdown while eliminating the INTVCC loading from preventing controller start-up.
Why should you defeat current latchoff? During the
prototyping stage of a design, there may be a problem with
noise pickup or poor layout causing the protection circuit
to latch off the controller. Defeating this feature allows
troubleshooting of the circuit and PC layout. The internal
short-circuit and foldback current limiting still remains
active, thereby protecting the power supply system from
failure. A decision can be made after the design is complete whether to rely solely on foldback current limiting or
to enable the latchoff feature by removing the pull-up
resistor.
3.3V OR 5V
D1
INTVCC
RUN/SS
RSS*
Phase-Locked Loop and Frequency Synchronization
The LTC1929 has a phase-locked loop comprised of an
internal voltage controlled oscillator and phase detector.
This allows the top MOSFET turn-on to be locked to the
rising edge of an external source. The frequency range of
the voltage controlled oscillator is ±50% around the
center frequency fO. A voltage applied to the PLLFLTR pin
of 1.2V corresponds to a frequency of approximately
220kHz. The nominal operating frequency range of the
LTC1929 is 140kHz to 310kHz.
The phase detector used is an edge sensitive digital type
which provides zero degrees phase shift between the
external and internal oscillators. This type of phase detector will not lock up on input frequencies close to the
harmonics of the VCO center frequency. The PLL hold-in
range, ∆fH, is equal to the capture range, ∆fC:
∆fH = ∆fC = ±0.5 fO (150kHz-300kHz)
The output of the phase detector is a complementary pair
of current sources charging or discharging the external
filter network on the PLLFLTR pin. A simplified block
diagram is shown in Figure 7.
2.4V
RLP
10k
PHASE
DETECTOR
EXTERNAL
OSC
CLP
PLLFLTR
RSS*
D1*
CSS > (COUT )(VOUT)(10-4)(RSENSE)
The minimum recommended soft-start capacitor of CSS =
0.1µF will be sufficient for most applications.
tLO1 ≈ (CSS • 0.6V)/(1.2µA) = 5 • 105 (CSS)
VIN
The value of the soft-start capacitor CSS may need to be
scaled with output voltage, output capacitance and load
current characteristics. The minimum soft-start capacitance is given by:
PLLIN
RUN/SS
CSS
50k
DIGITAL
PHASE/
FREQUENCY
DETECTOR
OSC
CSS
*OPTIONAL TO DEFEAT OVERCURRENT LATCHOFF
Figure 6. RUN/SS Pin Interfacing
18
1929 F06
1929 F07
Figure 7. Phase-Locked Loop Block Diagram
LTC1929/LTC1929-PG
U
W
U
U
APPLICATIO S I FOR ATIO
If the external frequency (fPLLIN) is greater than the oscillator frequency f0SC, current is sourced continuously,
pulling up the PLLFLTR pin. When the external frequency
is less than f0SC, current is sunk continuously, pulling
down the PLLFLTR pin. If the external and internal frequencies are the same but exhibit a phase difference, the
current sources turn on for an amount of time corresponding to the phase difference. Thus the voltage on the
PLLFLTR pin is adjusted until the phase and frequency of
the external and internal oscillators are identical. At this
stable operating point the phase comparator output is
open and the filter capacitor CLP holds the voltage. The
LTC1929 PLLIN pin must be driven from a low impedance
source such as a logic gate located close to the pin.
The loop filter components (CLP, RLP) smooth out the
current pulses from the phase detector and provide a
stable input to the voltage controlled oscillator. The filter
components CLP and RLP determine how fast the loop
acquires lock. Typically RLP =10kΩ and CLP is 0.01µF to
0.1µF.
Minimum On-Time Considerations
Minimum on-time tON(MIN) is the smallest time duration
that the LTC1929 is capable of turning on the top MOSFET.
It is determined by internal timing delays and the gate
charge required to turn on the top MOSFET. Low duty cycle
applications may approach this minimum on-time limit
and care should be taken to ensure that
tON(MIN) <
VOUT
()
VIN f
If the duty cycle falls below what can be accommodated by
the minimum on-time, the LTC1929 will begin to skip
cycles resulting in nonconstant frequency operation. The
output voltage will continue to be regulated, but the ripple
current and ripple voltage will increase.
The minimum on-time for the LTC1929 is generally less
than 200ns. However, as the peak sense voltage decreases
the minimum on-time gradually increases. This is of
particular concern in forced continuous applications with
low ripple current at light loads. If the duty cycle drops
below the minimum on-time limit in this situation, a
significant amount of cycle skipping can occur with correspondingly larger current and voltage ripple.
If an application can operate close to the minimum ontime limit, an inductor must be chosen that has a low
enough inductance to provide sufficient ripple amplitude
to meet the minimum on-time requirement. As a general
rule, keep the inductor ripple current of each phase equal
to or greater than 15% of IOUT(MAX) at VIN(MAX).
Efficiency Considerations
The percent efficiency of a switching regulator is equal to
the output power divided by the input power times 100%.
It is often useful to analyze individual losses to determine
what is limiting the efficiency and which change would
produce the most improvement. Percent efficiency can be
expressed as:
%Efficiency = 100% – (L1 + L2 + L3 + ...)
where L1, L2, etc. are the individual losses as a percentage
of input power.
Although all dissipative elements in the circuit produce
losses, four main sources usually account for most of the
losses in LTC1929 circuits: 1) LTC1929 VIN current (including loading on the differential amplifier output),
2) INTVCC regulator current, 3) I2R losses and 4) Topside
MOSFET transition losses.
1) The VIN current has two components: the first is the
DC supply current given in the Electrical Characteristics
table, which excludes MOSFET driver and control currents; the second is the current drawn from the differential
amplifier output. VIN current typically results in a small
(<0.1%) loss.
2) INTVCC current is the sum of the MOSFET driver and
control currents. The MOSFET driver current results from
switching the gate capacitance of the power MOSFETs.
Each time a MOSFET gate is switched from low to high to
low again, a packet of charge dQ moves from INTVCC to
ground. The resulting dQ/dt is a current out of INTVCC that
is typically much larger than the control circuit current. In
continuous mode, IGATECHG = (QT + QB), where QT and QB
are the gate charges of the topside and bottom side
MOSFETs.
19
LTC1929/LTC1929-PG
U
W
U
U
APPLICATIO S I FOR ATIO
Supplying INTVCC power through the EXTVCC switch input
from an output-derived source will scale the VIN current
required for the driver and control circuits by the ratio
(Duty Factor)/(Efficiency). For example, in a 20V to 5V
application, 10mA of INTVCC current results in approximately 3mA of VIN current. This reduces the mid-current
loss from 10% or more (if the driver was powered directly
from VIN) to only a few percent.
3) I2R losses are predicted from the DC resistances of the
fuse (if used), MOSFET, inductor, current sense resistor,
and input and output capacitor ESR. In continuous mode
the average output current flows through L and RSENSE,
but is “chopped” between the topside MOSFET and the
synchronous MOSFET. If the two MOSFETs have approximately the same RDS(ON), then the resistance of one
MOSFET can simply be summed with the resistances of L,
RSENSE and ESR to obtain I2R losses. For example, if each
RDS(ON)=10mΩ, RL=10mΩ, and RSENSE=5mΩ, then the
total resistance is 25mΩ. This results in losses ranging
from 2% to 8% as the output current increases from 3A to
15A per output stage for a 5V output, or a 3% to 12% loss
per output stage for a 3.3V output. Efficiency varies as the
inverse square of VOUT for the same external components
and output power level. The combined effects of increasingly lower output voltages and higher currents required
by high performance digital systems is not doubling but
quadrupling the importance of loss terms in the switching
regulator system!
4) Transition losses apply only to the topside MOSFET(s),
and only when operating at high input voltages (typically
20V or greater). Transition losses can be estimated from:
Transition Loss = (1.7) VIN2 IO(MAX) CRSS f
Other “hidden” losses such as copper trace and internal
battery resistances can account for an additional 5% to
10% efficiency degradation in portable systems. It is very
important to include these “system” level losses in the
design of a system. The internal battery and input fuse
resistance losses can be minimized by making sure that
CIN has adequate charge storage and a very low ESR at the
switching frequency. A 50W supply will typically require a
20
minimum of 200µF to 300µF of output capacitance having
a maximum of 10mΩ to 20mΩ of ESR. The LTC1929
2-phase architecture typically halves the input and output
capacitance requirements over competing solutions. Other
losses including Schottky conduction losses during deadtime and inductor core losses generally account for less
than 2% total additional loss.
Checking Transient Response
The regulator loop response can be checked by looking at
the load transient response. Switching regulators take
several cycles to respond to a step in DC (resistive) load
current. When a load step occurs, VOUT shifts by an
amount equal to ∆ILOAD(ESR), where ESR is the effective
series resistance of COUT(∆ILOAD) also begins to charge or
discharge COUT generating the feedback error signal that
forces the regulator to adapt to the current change and
return VOUT to its steady-state value. During this recovery
time VOUT can be monitored for excessive overshoot or
ringing, which would indicate a stability problem. The
availability of the ITH pin not only allows optimization of
control loop behavior but also provides a DC coupled and
AC filtered closed loop response test point. The DC step,
rise time, and settling at this test point truly reflects the
closed loop response. Assuming a predominantly second
order system, phase margin and/or damping factor can be
estimated using the percentage of overshoot seen at this
pin. The bandwidth can also be estimated by examining
the rise time at the pin. The ITH external components
shown in the Figure 1 circuit will provide an adequate
starting point for most applications.
The ITH series RC-CC filter sets the dominant pole-zero
loop compensation. The values can be modified slightly
(from 0.2 to 5 times their suggested values) to maximize
transient response once the final PC layout is done and the
particular output capacitor type and value have been
determined. The output capacitors need to be decided
upon because the various types and values determine the
loop feedback factor gain and phase. An output current
pulse of 20% to 80% of full-load current having a rise time
of <2µs will produce output voltage and ITH pin waveforms
LTC1929/LTC1929-PG
U
W
U
U
APPLICATIO S I FOR ATIO
that will give a sense of the overall loop stability without
breaking the feedback loop. The initial output voltage step
resulting from the step change in output current may not
be within the bandwidth of the feedback loop, so this signal
cannot be used to determine phase margin. This is why it
is better to look at the Ith pin signal which is in the feedback
loop and is the filtered and compensated control loop
response. The gain of the loop will be increased by
increasing RC and the bandwidth of the loop will be
increased by decreasing CC. If RC is increased by the same
factor that CC is decreased, the zero frequency will be kept
the same, thereby keeping the phase the same in the most
critical frequency range of the feedback loop. The output
voltage settling behavior is related to the stability of the
closed-loop system and will demonstrate the actual overall supply performance.
A second, more severe transient is caused by switching in
loads with large (>1µF) supply bypass capacitors. The
discharged bypass capacitors are effectively put in parallel
with COUT, causing a rapid drop in VOUT. No regulator can
alter its delivery of current quickly enough to prevent this
sudden step change in output voltage if the load switch
resistance is low and it is driven quickly. If the ratio of
CLOAD to COUT is greater than 1:50, the switch rise time
should be controlled so that the load rise time is limited to
approximately 25 • CLOAD. Thus a 10µF capacitor would
require a 250µs rise time, limiting the charging current to
about 200mA.
Automotive Considerations: Plugging into the
Cigarette Lighter
As battery-powered devices go mobile, there is a natural
interest in plugging into the cigarette lighter in order to
conserve or even recharge battery packs during operation.
But before you connect, be advised: you are plugging into
the supply from hell. The main battery line in an automobile is the source of a number of nasty potential transients,
including load-dump, reverse-battery, and double-battery.
Load-dump is the result of a loose battery cable. When the
cable breaks connection, the field collapse in the alternator
can cause a positive spike as high as 60V which takes
several hundred milliseconds to decay. Reverse-battery is
just what it says, while double-battery is a consequence of
tow truck operators finding that a 24V jump start cranks
cold engines faster than 12V.
The network shown in Figure 8 is the most straightforward
approach to protect a DC/DC converter from the ravages
of an automotive battery line. The series diode prevents
current from flowing during reverse-battery, while the
transient suppressor clamps the input voltage during
load-dump. Note that the transient suppressor should not
conduct during double-battery operation, but must still
clamp the input voltage below breakdown of the converter.
Although the LT1929 has a maximum input voltage of 36V,
most applications will be limited to 30V by the MOSFET
BVDSS.
50A IPK RATING
12V
TRANSIENT VOLTAGE
SUPPRESSOR
GENERAL INSTRUMENT
1.5KA24A
VIN
LTC1929
1929 F08
Figure 8. Automotive Application Protection
21
LTC1929/LTC1929-PG
U
W
U
U
APPLICATIO S I FOR ATIO
Design Example
As a design example, assume VIN = 5V (nominal), VIN␣ =␣ 5.5V
(max), VOUT = 1.8V, IMAX = 20A, TA = 70°C and f␣ =␣ 300kHz.
The inductance value is chosen first based on a 30% ripple
current assumption. The highest value of ripple current
occurs at the maximum input voltage. Tie the FREQSET pin
to the INTVCC pin for 300kHz operation. The minimum
inductance for 30% ripple current is:
L≥
≥
VOUT  VOUT 
 1−

VIN 
f ∆I 
( )
(
 1.8 V 
 1−

300kHz 30% 10 A  5.5V 
1.8 V
≥ 1.35µH
)( )( )
A 1.5µH inductor will produce 27% ripple current. The
peak inductor current will be the maximum DC value plus
one half the ripple current, or 11.4A. The minimum ontime occurs at maximum VIN:
tON(MIN) =
VOUT
1.8 V
=
= 1.1µs
VINf (5.5V )(300kHz)
The RSENSE resistors value can be calculated by using the
maximum current sense voltage specification with some
accomodation for tolerances:
50mV
RSENSE =
≈ 0.004Ω
11.4A
The power dissipation on the topside MOSFET can be
easily estimated. Using a Siliconix Si4420DY for example;
RDS(ON) = 0.013Ω, CRSS = 300pF. At maximum input
voltage with TJ (estimated) = 110°C at an elevated ambient
temperature:
PMAIN =
22
( ) [1+ (0.005)(110°C − 25°C)]
2
0.013Ω + 1.7(5.5V ) (10 A )(300pF )
(300kHz) = 0.65W
1.8 V
10
5.5V
2
The worst-case power disipated by the synchronous
MOSFET under normal operating conditions at elevated
ambient temperature and estimated 50°C junction temperature rise is:
( ) (1.48)(0.013Ω)
5.5V − 1.8 V
10 A
5.5V
= 1.29W
PSYNC =
2
A short-circuit to ground will result in a folded back current
of about:
ISC =
( )  = 6.6A

25mV
1 200ns 5.5V
+ 
0.004Ω 2  1.5µH



The worst-case power disipated by the synchronous
MOSFET under short-circuit conditions at elevated ambient temperature and estimated 50°C junction temperature
rise is:
( ) (1.48)(0.013Ω)
5.5V − 1.8 V
6.6 A
5.5V
= 564mW
PSYNC =
2
which is less than half of the normal, full-load dissipation.
Incidentally, since the load no longer dissipates power in
the shorted condition, total system power dissipation is
decreased by over 99%.
The duty factor for this application is:
DF =
VO 1.8 V
=
= 0.36
VIN
5V
Using Figure 4, the RMS ripple current will be:
IINRMS = (20A)(0.23) = 4.6ARMS
An input capacitor(s) with a 4.6ARMS ripple current rating
is required.
The output capacitor ripple current is calculated by using
the inductor ripple already calculated for each inductor
and multiplying by the factor obtained from Figure␣ 3
along with the calculated duty factor. The output ripple in
LTC1929/LTC1929-PG
U
U
W
U
APPLICATIO S I FOR ATIO
continuous mode will be highest at the maximum input
voltage since the duty factor is < 50%. The maximum
output current ripple is:
( )
VOUT
0.3 at 33% D F
fL
1.8 V
0.3
∆ICOUTMAX =
300kHz 1.5µH
∆ICOUT =
(
= 1.2ARMS
)(
(
)
)
VOUTRIPPLE = 20mΩ 1.2ARMS = 24mVRMS
PC Board Layout Checklist
When laying out the printed circuit board, the following
checklist should be used to ensure proper operation of the
LTC1929. These items are also illustrated graphically in
the layout diagram of Figure␣ 11. Check the following in
your layout:
1) Are the signal and power grounds segregated? The
LTC1929 signal ground pin should return to the (–) plate
of COUT separately. The power ground returns to the
sources of the bottom N-channel MOSFETs, anodes of the
Schottky diodes, and (–) plates of CIN, which should have
as short lead lengths as possible.
2) Does the LTC1929 VOS+ pin connect to the (+) plate(s)
of COUT? Does the LTC1929 VOS– pin connect to the (–)
plate(s) of COUT? The resistive divider R1, R2 must be
connected between the VDIFFOUT and signal ground and
any feedforward capacitor across R1 should be as close as
possible to the LTC1929.
3) Are the SENSE – and SENSE + leads routed together with
minimum PC trace spacing? The filter capacitors between
SENSE + and SENSE – pin pairs should be as close as
possible to the LTC1929. Ensure accurate current sensing
with Kelvin connections.
4) Do the (+) plates of CIN connect to the drains of the
topside MOSFETs as closely as possible? This capacitor
provides the AC current to the MOSFETs. Keep the input
current path formed by the input capacitor, top and bottom
MOSFETs, and the Schottky diode on the same side of the
PC board in a tight loop to minimize conducted and
radiated EMI.
5) Is the INTVCC 1µF ceramic decoupling capacitor connected closely between INTVCC and the power ground pin?
This capacitor carries the MOSFET driver peak currents. A
small value is used to allow placement immediately adjacent to the IC.
6) Keep the switching nodes, SW1 (SW2), away from
sensitive small-signal nodes. Ideally the switch nodes
should be placed at the furthest point from the LTC1929.
7) Use a low impedance source such as a logic gate to drive
the PLLIN pin and keep the lead as short as possible.
The diagram in Figure 9 illustrates all branch currents in
a 2-phase switching regulator. It becomes very clear after
studying the current waveforms why it is critical to keep
the high-switching-current paths to a small physical size.
High electric and magnetic fields will radiate from these
“loops” just as radio stations transmit signals. The output capacitor ground should return to the negative terminal of the input capacitor and not share a common
ground path with any switched current paths. The left half
of the circuit gives rise to the “noise” generated by a
switching regulator. The ground terminations of the
synchronous MOSFETs and Schottky diodes should return to the bottom plate(s) of the input capacitor(s) with
a short isolated PC trace since very high switched currents are present. A separate isolated path from the
bottom plate(s) of the input capacitor(s) should be used
to tie in the IC power ground pin (PGND) and the signal
ground pin (SGND). This technique keeps inherent signals generated by high current pulses from taking alternate current paths that have finite impedances during the
total period of the switching regulator. External OPTILOOP compensation allows overcompensation for PC
layouts which are not optimized but this is not the
recommended design procedure.
23
LTC1929/LTC1929-PG
U
W
U
U
APPLICATIO S I FOR ATIO
Simplified Visual Explanation of How a 2-Phase
Controller Reduces Both Input and Output RMS Ripple
Current
A multiphase power supply significantly reduces the
amount of ripple current in both the input and output
capacitors. The RMS input ripple current is divided by, and
the effective ripple frequency is multiplied up by the
number of phases used (assuming that the input voltage
is greater than the number of phases used times the output
voltage). The output ripple amplitude is also reduced by,
and the effective ripple frequency is increased by the
number of phases used. Figure 10 graphically illustrates
the principle.
The worst-case RMS ripple current for a single stage
design peaks at twice the value of the output voltage . The
worst-case RMS ripple current for a two stage design
results in peaks at 1/4 and 3/4 of input voltage. When the
RMS current is calculated, higher effective duty factor
results and the peak current levels are divided as long as
the currents in each stage are balanced. Refer to Application Note 19 for a detailed description of how to calculate
RMS current for the single stage switching regulator.
Figures 3 and 4 illustrate how the input and output
currents are reduced by using an additional phase. The
input current peaks drop in half and the frequency is
doubled for this 2-phase converter. The input capacity
requirement is thus reduced theoretically by a factor of
four! Ceramic input capacitors with their unbeatably low
ESR characteristics can be used.
24
Figure 4 illustrates the RMS input current drawn from the
input capacitance vs the duty cycle as determined by the
ratio of input and output voltage. The peak input RMS
current level of the single phase system is reduced by 50%
in a 2-phase solution due to the current splitting between
the two stages.
An interesting result of the 2-phase solution is that the VIN
which produces worst-case ripple current for the input
capacitor, VOUT = VIN/2, in the single phase design produces zero input current ripple in the 2-phase design.
The output ripple current is reduced significantly when
compared to the single phase solution using the same
inductance value because the VOUT/L discharge current
term from the stage that has its bottom MOSFET on
subtracts current from the (VIN - VOUT)/L charging current
resulting from the stage which has its top MOSFET on. The
output ripple current is:
∆IRIPPLE =
( ) 

2VOUT  1 − 2D 1 − D
fL  1 − 2D + 1



where D is duty factor.
The input and output ripple frequency is increased by the
number of stages used, reducing the output capacity
requirements. When VIN is approximately equal to 2(VOUT)
as illustrated in Figures 3 and 4, very low input and output
ripple currents result.
LTC1929/LTC1929-PG
U
U
W
U
APPLICATIO S I FOR ATIO
SW1
L1
RSENSE1
D1
VIN
VOUT
RIN
CIN
+
+
SW2
L2
COUT
RL
RSENSE2
D2
BOLD LINES INDICATE
HIGH, SWITCHING
CURRENT LINES.
KEEP LINES TO A
MINIMUM LENGTH.
1929 F09
Figure 9. Instantaneous Current Path Flow in a Multiple Phase Switching Regulator
SINGLE PHASE
SW V
ICIN
DUAL PHASE
SW1 V
SW2 V
IL1
ICOUT
IL2
ICIN
ICOUT
RIPPLE
1929 F10
Figure 10. Single and 2-Phase Current Waveforms
25
26
R2
2.7k
C11 1nF
R3
10k
R6
8.06k
C15
470pF
R5 10k
C10 100pF
C9 0.01µF
C7
0.1µF
R7
8.06k
C17
1000pF
C1 1000pF
14
13
12
11
10
9
8
7
6
5
4
3
2
1
SENSE1 –
AMPMD
15
16
17
18
19
20
21
22
23
24
25
26
27
28
C13
2.2µF
C8
0.47µF
C3, C4: OS-CON 6SP680M
C18–C21: T510E108M004
L1, L2: SUMIDA CEP149-1R0MC
Q1–Q8: FDS6670A OR FDS7760A
C12
1µF
R1
10Ω
C14
10µF
1
3
2
+
Figure 11. 5V Input, 1.6V/40A CPU Power Supply
SENSE2
+
TG2
SW2
VOS +
SENSE2 –
BOOST2
BG2
VOS –
VDIFFOUT
PGND
INTVCC
ITH
SGND
EXTVCC
BG1
PLLIN
NC
VIN
PLLFLTR
BOOST1
SW1
SENSE1 +
EAIN
NC
TG1
RUN/SS
U1
LTC1929
C2
1µF
+
R9
50Ω
C18
C16
0.47µF
D1
BAT54A
C19
+
Q7
Q5
C20
Q3
Q1
C22
1µF
R10
50Ω
+
Q8
Q6
C21
Q4
+
C4
VIN+
VIN–
5V
VOSENSE +
REMOTE SENSE
VOSENSE –
VOUT –
1.6V/40A
VOUT +
R8
0.002Ω
R4
0.002Ω
1929 F11
C24
10µF
C3
L1
1µH
L2
1µH
+
Q2
C23
1µF
LTC1929/LTC1929-PG
TYPICAL APPLICATIO S
U
LTC1929/LTC1929-PG
U
TYPICAL APPLICATIO S
100
EFFICIENCY (%)
90
80
70
60
VIN = 5V
VOUT = 1.6V
50
0
5
10
15 20 25 30
LOAD CURRENT (A)
35
40
1929 F12
Figure 12. Efficiency Plot for Circuit of Figure 11
U
PACKAGE DESCRIPTIO
Dimensions in inches (millimeters) unless otherwise noted.
G Package
28-Lead Plastic SSOP (0.209)
(LTC DWG # 05-08-1640)
10.07 – 10.33*
(0.397 – 0.407)
28 27 26 25 24 23 22 21 20 19 18 17 16 15
7.65 – 7.90
(0.301 – 0.311)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
5.20 – 5.38**
(0.205 – 0.212)
1.73 – 1.99
(0.068 – 0.078)
0° – 8°
0.13 – 0.22
(0.005 – 0.009)
0.55 – 0.95
(0.022 – 0.037)
NOTE: DIMENSIONS ARE IN MILLIMETERS
*DIMENSIONS DO NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.152mm (0.006") PER SIDE
**DIMENSIONS DO NOT INCLUDE INTERLEAD FLASH. INTERLEAD
FLASH SHALL NOT EXCEED 0.254mm (0.010") PER SIDE
0.65
(0.0256)
BSC
0.25 – 0.38
(0.010 – 0.015)
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
0.05 – 0.21
(0.002 – 0.008)
G28 SSOP 1098
27
LTC1929/LTC1929-PG
U
TYPICAL APPLICATIO
LTC1929-PG
0.1µF
1000pF
2.7k
RUN/SS
NC
2
SENSE1 +
TG1
3
SENSE1 –
SW1
4
10k
5
INTVCC
6
51k
15k
7
47k
8
3.3nF
100pF
9
10
470pF
11
10k
15k
PLLFLTR
PLLIN
BOOST1
VIN
BG1
NC
EXTVCC
ITH
INTVCC
SGND
VDIFFOUT
PGND
BG2
VOS –
BOOST2
VOS +
SW2
13
SENSE2 –
TG2
14
SENSE2 +
PGOOD
12
1000pF
EAIN
28
L1
27
0.004Ω
26
25
0.22µF
M1
M2
24
D1
MBRS140T3
23
22
10Ω
5V (OPT)
CIN
47µF 35V
+
21
20
0.1µF
10µF
+
1
COUT
19
18
17
M3
0.22µF
M4
D2
MBRS140T3
VOUT
2V
20A
0.004Ω
16
100k
15
L2
PGOOD
1929 F13
VIN
5V TO 28V
SWITCHING FREQUENCY = 200kHz
CIN: 5A RIPPLE CURRENT RATING REQUIRED
COUT: 4 × 180µF/4V PANASONIC SP
L1 TO L2: 1.5µH SUMIDA CEP125-1R5MC
M1 TO M4: FAIRCHILD FDS7760A
Figure 13. 2V/20A CPU Power Supply with Active Voltage Positioning
RELATED PARTS
PART NUMBER
DESCRIPTION
LTC1438/LTC1439
Dual High Efficiency Low Noise Synchronous Step-Down Switching Regulators POR, Auxiliary Regulator
COMMENTS
LTC1438-ADJ
Dual Synchronous Controller with Auxiliary Regulator
POR, External Feedback Divider
LTC1538-AUX
Dual High Efficiency Low Noise Synchronous Step-Down Switching Regulator
Auxiliary Regulator, 5V Standby
LTC1539
Dual High Efficiency Low Noise Synchronous Step-Down Switching Regulator
5V Standby, POR, Low-Battery, Aux Regulator
LTC1435/LTC1435A
High Efficiency Synchronous Step-Down Switching Regulator
Burst ModeTM Operation, 16-Pin Narrow SO
LTC1436A-PLL
High Efficiency Low Noise Synchronous Step-Down Switching Regulator
Adaptive PowerTM Mode, 24-Pin SSOP
LTC1628/LTC1628-PG Dual High Efficiency, 2-Phase Synchronous Step-Down Switching Regulator
Constant Frequency, Standby, 5V and 3.3V LDOs
LTC1629/LTC1629-PG PolyPhase High Efficiency Controller
Expandable Up to 12 Phases, G-28, Up to 120A
LTC1702/LTC1703
Dual High Efficiency, 2-Phase Synchronous Step-Down Switching Regulator
500kHz, 25MHz GBW
LTC1735
High Efficiency Synchronous Step-Down Controller
Burst Mode Operation, 16-Pin Narrow SSOP,
Fault Protection, 3.5V ≤ VIN ≤ 36V
LTC1736
High Efficiency Synchronous Step-Down Controller with 5-Bit VID
Output Fault Protection, Power Good, GN-24,
3.5V ≤ VIN ≤ 36V, 0.8V ≤ VOUT ≤ 6V
Adaptive Power and Burst Mode are trademarks of Linear Technology Corporation.
28
Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408)432-1900 ● FAX: (408) 434-0507 ● www.linear-tech.com
1929f LT/TP 0500 4K • PRINTED IN USA
 LINEAR TECHNOLOGY CORPORATION 1999