Fairchild FAN5355UC02X 1a / 0.8a, 3mhz digitally programmable tinybucktm regulator Datasheet

FAN5355
1A / 0.8A, 3MHz Digitally Programmable TinyBuckTM Regulator
Features
Description

91% Efficiency at 3MHz

I C™-Compatible Interface up to 3.4Mbps
(1)
800mA or 1A Output Current
2.7V to 5.5V Input Voltage Range
6 or 7-bit VOUT Programmable from 0.75 to 1.975V
3MHz Fixed-Frequency Operation
Excellent Load and Line Transient Response
Small Size, 1μH Inductor Solution
±2% PWM DC Voltage Accuracy
35ns Minimum On-Time
High-Efficiency, Low-Ripple, Light-Load PFM
Smooth Transition between PWM and PFM
37μA Operating PFM Quiescent Current
Software Selectable 25kHz Minimum PFM Frequency
Prevents Audible Noise in PFM Mode
2
2
Pin-Selectable or I C™ Programmable Output Voltage
On-the-Fly External Clock Synchronization
10-lead MLP (3 x 3mm) or 12-bump CSP Packages
Applications

SmartReflex™-Compliant Power Supply

Micro DC-DC Converter Modules
Split Supply DSPs and μP Solutions OMAP™, XSCALE™
Cell Phones, Smart Phones, PDAs, Digital Cameras, and
Portable Media Players
®
Handset Graphic Processors (NVIDIA , ATI)
I2C is a trademark of Philips Corporation.
SmartReflex and OMAP are trademarks of Texas Instruments.
XSCALE is a trademark of Intel Corporation.
NVIDIA is a registered trademark of NVIDIA Corporation.
© 2008 Fairchild Semiconductor Corporation
FAN5355 • Rev. 1.0.4
The FAN5355 device is a high-frequency, ultra-fast transient
response, synchronous step-down DC-DC converter
optimized for low-power applications using small, low-cost
inductors and capacitors. The FAN5355 supports up to
(1)
800mA or 1A load current.
The device is ideal for mobile phones and similar portable
applications powered by a single-cell Lithium-Ion battery. With
2
an output voltage range adjustable via I C™ interface from
0.75V to 1.975V, the device supports low-voltage DSPs and
processors, core power supplies in smart phones, PDAs, and
handheld computers.
The FAN5355 operates at 3MHz (nominal) fixed switching
frequency using either its internal oscillator or external SYNC
frequency.
During light-load conditions, the regulator includes a PFM
mode to enhance light-load efficiency. The regulator
transitions smoothly between PWM and PFM modes with no
glitches on VOUT. Normal PFM (NPFM) mode offers the lowest
quiescent current, at the expense of setpoint accuracy.
Enhanced PFM (EPFM) mode features higher accuracy, as
well as a 25kHz minimum PFM frequency, designed to
prevent the regulator from operating in the audible range. In
shutdown, the current consumption is reduced to less than
2μA, using software shutdown (EN = 1 with EN_DCDC = 0),
and less than 200nA in hardware shutdown (EN = 0).
The serial interface is compatible with Fast/Standard and
2
High-Speed mode I C specifications, allowing transfers up to
3.4Mbps. This interface is used for dynamic voltage scaling
with 12.5mV voltage steps, for reprogramming the mode of
operation (PFM or Forced PWM), or to disable/enable the
output voltage.
The chip's advanced protection features include short-circuit
protection and current and temperature limits. During a
sustained over-current event, the IC shuts down and restarts
after a delay to reduce average power dissipation into a fault.
During start-up, the IC controls the output slew rate to
minimize input current and output overshoot at the end of softstart. The IC maintains a consistent soft-start ramp, regardless
of output load during start-up.
The FAN5355 is available in 10-lead MLP (3x3mm) and
12-bump CSP packages.
www.fairchildsemi.com
FAN5355 — 1A / 0.8A, 3Mhz. Digitally Programmable TinyBuckTM Regulator
March 2008
Slave
Address LSB
Order Number
(4)
Option
A1
A0
DAC
FAN5355UC00X
FAN5355MP00X
FAN5355UC02X
00
00
02
0
0
1
0
0
0
6
6
6
FAN5355UC03X
FAN5355UC06X
FAN5355UC07X
03
(1)
06
(1)
07
0
0
1
0
0
1
6
6
7
FAN5355MP07X
(1)
1
1
7
07
Power-up
Defaults
VOUT Programming
MIN.
MAX.
0.7500
0.7500
0.7500
0.7500
1.1875
1.5375
1.5375
0.7500
(3)
0.7500
(3)
1.4375
1.5375
1.9750
1.9750
Package
VSEL0 VSEL1
(2)
1.9750
(4)
1.05
1.05
1.05
1.35
1.35
1.20
WLCSP-12, 2.23x1.46mm
MLP-10, 3x3mm
WLCSP-12, 2.23x1.46mm
1.00
1.80
1.05
1.20
1.80
1.35
WLCSP-12, 2.23x1.46mm
WLCSP-12, 2.23x1.46mm
WLCSP-12, 2.23x1.46mm
1.05
1.35
MLP-10, 3x3mm
Notes:
1. Option 06 and 07 is rated for 1A output current. All other options are rated for 800mA output current.
2. VOUT is limited to the maximum voltage for all VSEL codes greater than the maximum VOUT listed.
3. VOUT may be programmed down 100mV for option 07. Performance below 0.75V is not guaranteed.
4.
All packages are “green” per JEDEC: J-STD-020B standard. The “X” designator specifies tape and reel packaging.
Typical Application
AVIN
PVIN
Q1
VIN
CIN
EN
VSEL
MODULATOR
VCCIO
VOUT
SW
SYNC
Q2
L OUT
COUT
SDA
SCL
PGND
AGND
VOUT
Figure 1. Typical Application
Component
Description
Vendor
Parameter
Min.
Typ.
Max.
Units
L(5)
0.7
1.0
1.2
μH
L1 (LOUT)
1μH nominal
Murata LQM31P
or FDK MIPSA2520
COUT
0603 (1.6x0.8x0.8)
10μF X5R or better
Murata or equivalent
GRM188R60G106ME47D
C(6)
5.6
10.0
12.0
μF
CIN
0603 (1.6x0.8x0.8)
4.7μF X5R or better
Murata or equivalent
GRM188R60J475KE19D
C(6)
3.0
4.7
5.6
μF
DCR (series R)
100
mΩ
Table 1. Recommended External Components
Notes:
5. Minimum L incorporates both tolerance, temperature, and partial saturation effects (L decreases with increasing current).
6. Minimum C is a function of initial tolerance, maximum temperature, and the effective capacitance being reduced due to
frequency, dielectric, and voltage bias effects.
© 2008 Fairchild Semiconductor Corporation
FAN5355 • Rev. 1.0.4
2
www.fairchildsemi.com
FAN5355 — 1A / 0.8A, 3Mhz. Digitally Programmable TinyBuckTM Regulator
Ordering Information
A1
A2
A3
A3
A2
A1
B1
B2
B3
B3
B2
B1
PVIN 1
10 SW
AVIN 2
9 PGND
PAD
SDA 3
C1
C2
C3
C3
C2
C1
D1
D2
D3
D3
D2
D1
Top View
8 AGND
AGND
SCL 4
7 EN
VSEL 5
6 VOUT
Top View
Bottom View
Figure 2. WLCSP- 12, 2.23x1.46mm
Figure 3. MLP10, 3x3mm
Pin Definitions
Pin #
Name
Description
9
PGND
Power GND. Power return for gate drive and power transistors. Connect to AGND on PCB. The
connection from this pin to the bottom of CIN should be as short as possible.
A2
10
SW
A3
1
PVIN
Power Input Voltage. Connect to input power source. The connection from this pin to CIN should be as
short as possible.
B2
N/A
SYNC
Sync. When toggling and SYNC_EN bit is HIGH, the regulator synchronizes to the frequency on this pin.
In PWM mode, when this pin is statically LOW or statically HIGH, or when its frequency is outside of the
specified capture range, the regulator’s frequency is controlled by its internal 3MHz clock.
B3
2
AVIN
Analog Input Voltage. Connect to input power source as close as possible to the input bypass
capacitor.
C1
8, PAD
AGND
Analog GND. This is the signal ground reference for the IC. All voltage levels are measured with respect
to this pin.
C2
7
EN
C3
3
SDA
D1
6
VOUT
Output Voltage Monitor. Tie this pin to the output voltage. This is a signal input pin to the control circuit
and does not carry DC current.
D2
5
VSEL
Voltage Select. When HIGH, VOUT is set by VSEL1. When LOW, VOUT is set by VSEL0. This behavior
can be overridden through I2C register settings. This pin should not be left floating.
D3
4
SCL
WLCSP
MLP
A1, B1
Switching Node. Connect to output inductor.
Enable. When this pin is HIGH, the circuit is enabled. When LOW, quiescent current is minimized. This
pin should not be left floating.
SDA. I2C interface serial data.
SCL. I2C interface serial clock.
Note:
7. All logic inputs (SDA, SCL, SYNC, EN, and VSEL) are high impedance and should not be left floating. For minimum
quiescent power consumption, tie unused logic inputs to AVIN or AGND. If I2C control is unused, tie SDA and SCL to AVIN.
© 2008 Fairchild Semiconductor Corporation
FAN5355 • Rev. 1.0.4
3
www.fairchildsemi.com
FAN5355 — 1A / 0.8A, 3Mhz. Digitally Programmable TinyBuckTM Regulator
Pin Configuration
Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above
the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended
exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings
are stress ratings only.
Symbol
VCC
Parameter
Min.
Max.
AVIN, SW, PVIN Pins
-0.3
6.5
Other Pins
ESD
-0.3
Electrostatic Discharge Protection Level
Human Body Model per JESD22-A114
Units
V
(8)
V
AVIN + 0.3
3.5
Charged Device Model per JESD22-C101
KV
1.5
KV
TJ
Junction Temperature
–40
+150
°C
TSTG
Storage Temperature
–65
+150
°C
+260
°C
TL
Lead Soldering Temperature, 10 Seconds
Note:
8. Lesser of 6.5V or VCC+0.3V.
Recommended Operating Conditions
The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended operating
conditions are specified to ensure optimal performance to the datasheet specifications. Fairchild does not recommend exceeding
them or designing to absolute maximum ratings.
Symbol
VIN
f
Parameter
Min.
Max.
Units
Supply Voltage
2.7
5.5
V
Frequency Range
2.7
3.3
MHz
2.5
V
SDA and SCL Voltage Swing(9)
VSW
TA
Ambient Temperature
–40
+85
°C
TJ
Junction Temperature
–40
+125
°C
Note:
9.
2
The I C interface operates with tHD;DAT = 0 as long as the pull-up voltage for SDA and SCL is less than 2.5V. If voltage
2
swings greater than 2.5V are required (for example if the I C bus is pulled up to VIN), the minimum tHD;DAT must be
2
increased to 80ns. Most I C masters change SDA near the midpoint between the falling and rising edges of SCL, which
provides ample tHD;DAT .
Dissipation Ratings(10)
Package
(11)
RθJA
Power Rating at TA ≤ 25°C
Derating Factor > TA = 25ºC
Molded Leadless Package (MLP)
49ºC/W
2050mW
21mW/ºC
Wafer-Level Chip-Scale Package (WLCSP)
110ºC/W
900mW
9mW/ºC
Notes:
10. Maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any
allowable ambient temperature is PD = [TJ(max) - TA ] / θJA.
11. This thermal data is measured with high-K board (four-layer board according to JESD51-7 JEDEC standard).
© 2008 Fairchild Semiconductor Corporation
FAN5355 • Rev. 1.0.4
4
www.fairchildsemi.com
FAN5355 — 1A / 0.8A, 3Mhz. Digitally Programmable TinyBuckTM Regulator
Absolute Maximum Ratings
VIN = 3.6V, EN = VIN, VSEL = VIN, SYNC = GND, VSEL0(6) bit = 1, CONTROL2[4:3] = 00. TA = -40°C to +85°C, unless otherwise
noted. Typical values are at TA = 25°C. Circuit and components according to Figure 1.
Symbol
Parameter
Conditions
Min.
Typ.
Max.
Units
5.5
V
110
150
μA
IO = 0mA, NPFM Mode
37
50
IO = 0mA, 3MHz PWM Mode
4.8
EN = GND
0.1
2.0
EN = VIN, EN_DCDC bit = 0,
SDA = SCL = VIN
0.1
2.0
Power Supplies
VIN
Input Voltage Range
IQ
Quiescent Current
2.7
IO = 0mA, EPFM Mode, FPFM = 25kHz
I SD
Shutdown Supply Current
VUVLO
Under-Voltage Lockout Threshold
VUVHYST
Under-Voltage Lockout Hysteresis
VIN Rising
VIN Falling
μA
mA
μA
2.40
2.60
V
2.00
2.15
2.30
V
200
250
300
mV
ENABLE, VSEL, SDA, SCL, SYNC
VIH
HIGH-Level Input Voltage
VIL
LOW-Level Input Voltage
IIN
Input Bias Current
1.2
V
Input tied to GND or VIN
0.01
VIN = 3.6V, CSP Package
145
VIN = 3.6V, MLP Package
165
VIN = 2.7V, MLP Package
200
0.4
V
1.00
μA
Power Switch and Protection
RDS(ON)P
ILKGP
P-channel MOSFET On Resistance
P-channel Leakage Current
VDS = 6V
1
VIN = 3.6V, CSP Package
75
N-channel MOSFET On Resistance
VIN = 3.6V, MLP Package
95
VIN = 2.7V, MLP Package
101
ILKGN
N-channel Leakage Current
VDS = 6V
RDIS
Discharge Resistor for Power-down
Sequence
Options 03, 06, 07
RDS(ON)N
mΩ
μA
mΩ
1
μA
15
50
Ω
2.7V ≤ VIN ≤ 4.2V, All Options Except 06
and 07
1150
1350
1600
2.7V ≤ VIN ≤ 5.5V, All Options Except 06
and 07
1050
1350
1600
2.7V ≤ VIN ≤ 4.2V, 06 and 07 Option
1300
1550
1800
ILIMPK
P-MOS Current Limit
TLIMIT
Thermal Shutdown
150
°C
THYST
Thermal Shutdown Hysteresis
20
°C
mA
Frequency Control
fSW
fSYNC
Oscillator Frequency
2.65
3.00
3.35
MHz
Synchronization Range
2.7
3.0
3.3
MHz
DSYNC
Synchronization Duty Cycle
20
80
%
fSYNCVAL
SYNC Frequency Rejection
1.6
4.3
MHz
fPFM(MIN)
Minimum PFM Frequency
EPFM Mode, ILOAD = 0
25
kHz
Continued on the following page…
© 2008 Fairchild Semiconductor Corporation
FAN5355 • Rev. 1.0.4
5
www.fairchildsemi.com
FAN5355 — 1A / 0.8A, 3Mhz. Digitally Programmable TinyBuckTM Regulator
Electrical Specifications
VIN = 3.6V, EN = VIN, VSEL = VIN, SYNC = GND, VSEL0(6) bit = 1, CONTROL2[4:3] = 00. TA = -40°C to +85°C, unless otherwise
noted. Typical values are at TA = 25°C. Circuit and components according to Figure 1
Symbol
Parameter
Conditions
Min.
IOUT(DC) = 0, Forced PWM, VOUT = 1.35V
Typ.
Max.
Units
Output Regulation
Option 00
Option 02
Option 03
VOUT
VOUT Accuracy
Option 06
Option 07
–1.5
1.5
%
2.7V ≤ VIN ≤ 5.5V, VOUT from 0.75 to 1.5375,
IOUT(DC) = 0 to 800mA, Forced PWM
–2
2
%
2.7V ≤ VIN ≤ 5.5V, VOUT from 0.75 to 1.5375,
IOUT(DC) = 0 to 800mA, NPFM Mode
–1.5
3.5
%
IOUT(DC) = 0, Forced PWM, VOUT = 1.20V
–1.5
1.5
%
2.7V ≤ VIN ≤ 5.5V, VOUT from 0.75 to 1.4375,
IOUT(DC) = 0 to 800mA, Forced PWM
–2
2
%
2.7V ≤ VIN ≤ 5.5V, VOUT from 0.75 to 1.4375,
IOUT(DC) = 0 to 800mA, NPFM Mode
–1.5
3.5
%
IOUT(DC) = 0, Forced PWM, VOUT = 1.20V
–1.5
1.5
%
2.7V ≤ VIN ≤ 5.5V, VOUT from 0.75 to 1.5375,
IOUT(DC) = 0 to 800mA, Forced PWM
–2
2
%
2.7V ≤ VIN ≤ 5.5V, VOUT from 0.75 to 1.5375,
IOUT(DC) = 0 to 800mA, NPFM Mode
–1.5
3.5
%
2.7V ≤ VIN ≤ 5.5V, VOUT from 0.75 to 1.5375,
IOUT(DC) = 0 to 800mA, EPFM Mode
–0.5
2
%
IOUT(DC) = 0, Forced PWM, VOUT = 1.800V
–1.5
1.5
%
2.7V ≤ VIN ≤ 5.5V, VOUT from 1.185 to 1.975,
IOUT(DC) = 0 to 1A, Forced PWM
–2
2
%
2.7V ≤ VIN ≤ 5.5V, VOUT from 1.185 to 1.975,
IOUT(DC) = 0 to 1A, NPFM Mode
–1.5
3.5
%
2.7V ≤ VIN ≤ 5.5V, VOUT from 1.185 to 1.975,
IOUT(DC) = 0 to 1A, EPFM Mode
–0.5
2
%
IOUT(DC) = 0, Forced PWM, VOUT = 1.35V
–1.5
1.5
%
2.7V ≤ VIN ≤ 5.5V, VOUT from 0.75 to 1.6875,
IOUT(DC) = 0 to 1A, Forced PWM
–2
2
%
2.7V ≤ VIN ≤ 5.5V, VOUT from 0.75 to 1.6875,
IOUT(DC) = 0 to 1A, NPFM Mode
–1.5
3.5
%
2.7V ≤ VIN ≤ 5.5V, VOUT from 0.75 to 1.6875,
IOUT(DC) = 0 to 1A, EPFM Mode
–0.5
2
%
ΔVOUT
ΔILOAD
Load Regulation
IOUT(DC) = 0 to 800mA, Forced PWM
–0.5
%/A
ΔVOUT
ΔVIN
Line Regulation
2.7V ≤ VIN ≤ 5.5V, IOUT(DC) = 300mA
0
%/V
VRIPPLE
Output Ripple Voltage
PWM Mode, VOUT = 1.35V
2.2
mVP-P
PFM Mode, IOUT(DC) = 10mA
20
mVP-P
Continued on the following page…
© 2008 Fairchild Semiconductor Corporation
FAN5355 • Rev. 1.0.4
6
www.fairchildsemi.com
FAN5355 — 1A / 0.8A, 3Mhz. Digitally Programmable TinyBuckTM Regulator
Electrical Specifications (Continued)
VIN = 3.6V, EN = VIN, VSEL = VIN, SYNC = GND, VSEL0(6) bit = 1, CONTROL2[4:3] = 00. TA = -40°C to +85°C, unless otherwise
noted. Typical values are at TA = 25°C. Circuit and components according to Figure 1.
Symbol
Parameter
Conditions
Min.
Typ.
Max.
Units
DAC
Resolution
Differential Nonlinearity
Option 07
7
Bits
All Other Options
6
Bits
Monotonicity Assured by Design
0.8
LSB
Timing
I2CEN
EN HIGH to I2C Start
tV(L-H)
VOUT LOW to HIGH Settling
μs
250
RLOAD = 75Ω, Transition from 1.0 to 1.5375V
VOUT Settled to within 2% of Setpoint
μs
7
Soft-Start
tSS
VSLEW
Regulator Enable
to Regulated
VOUT
Option 06
RLOAD > 5Ω, to VOUT = 1.8000V
170
210
μs
All Other
Options
RLOAD > 5Ω, to VOUT = Power-up Default
140
180
μs
Soft-start VOUT Slew Rate(12)
18.75
V/ms
Note:
12. Option 06 slew rate is 35.5V/ms during the first 16μs of soft-start.
AVIN
PVIN
Q1
7-bit
DAC
EN
VSEL
SYNC
SDA
I2C
INTERFACE
AND LOGIC
SCL
VIN
CIN
REF
FPWM
VOUT
SW
SOFT START
Q2
MODULATOR
L OUT
COUT
EN_REG
PGND
CLK
VOUT
AGND
3 MHz Osc
Figure 4. Block Diagram
© 2008 Fairchild Semiconductor Corporation
FAN5355 • Rev. 1.0.4
7
www.fairchildsemi.com
FAN5355 — 1A / 0.8A, 3Mhz. Digitally Programmable TinyBuckTM Regulator
Electrical Specifications (Continued)
Guaranteed by design.
Symbol
Parameter
Conditions
fSCL
SCL Clock Frequency
Standard mode
Fast mode
High-Speed mode, CB < 100pF
High-Speed mode, CB < 400pF
tBUF
Bus-free Time between STOP and
START Conditions
tHD;STA
START or Repeated START Hold
Time
tLOW
tHIGH
SCL LOW Period
SCL HIGH Period
tSU;STA
Repeated START Setup Time
tSU;DAT
Data Setup Time
(9)
tHD;DAT
Data Hold Time
tRCL
SCL Rise Time
tFCL
tRDA
tRCL1
tFDA
tSU;STO
CB
SCL Fall Time
SDA Rise Time
Rise Time of SCL After a Repeated
START Condition and After ACK Bit
SDA Fall Time
Stop Condition Setup Time
Min.
Max.
Units
100
400
3400
1700
kHz
kHz
kHz
kHz
Standard mode
4.7
μs
Fast mode
1.3
μs
Standard mode
Fast mode
High-Speed mode
Standard mode
Fast mode
High-Speed mode, CB < 100pF
High-Speed mode, CB < 400pF
Standard mode
Fast mode
High-Speed mode, CB < 100pF
High-Speed mode, CB < 400pF
Standard mode
Fast mode
High-Speed mode
Standard mode
Fast mode
High-Speed mode
Standard mode
Fast mode
High-Speed mode, CB < 100pF
High-Speed mode, CB < 400pF
Standard mode
Fast mode
High-Speed mode, CB < 100pF
High-Speed mode, CB < 400pF
Standard mode
Fast mode
High-Speed mode, CB < 100pF
High-Speed mode, CB < 400pF
Standard mode
Fast mode
High-Speed mode, CB < 100pF
High-Speed mode, CB < 400pF
Standard mode
Fast mode
High-Speed mode, CB < 100pF
High-Speed mode, CB < 400pF
Standard mode
Fast mode
High-Speed mode
4
600
160
4.7
1.3
160
320
4
600
60
120
4.7
600
160
250
100
10
μs
ns
ns
Capacitive Load for SDA and SCL
© 2008 Fairchild Semiconductor Corporation
FAN5355 • Rev. 1.0.4
Typ.
8
0
0
0
0
20+0.1CB
20+0.1CB
10
20
20+0.1CB
20+0.1CB
10
20
20+0.1CB
20+0.1CB
10
20
20+0.1CB
20+0.1CB
10
20
4
600
160
μs
ns
ns
ns
μs
ns
ns
ns
μs
ns
ns
ns
ns
ns
3.45
900
70
150
1000
300
80
160
300
300
40
80
1000
300
80
160
300
300
80
160
μs
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
400
μs
ns
ns
pF
www.fairchildsemi.com
FAN5355 — 1A / 0.8A, 3Mhz. Digitally Programmable TinyBuckTM Regulator
I2C Timing Specifications
tF
tSU;STA
tBUF
SDA
tR
SCL
TSU;DAT
tHD;STO
tHIGH
tLOW
tHD;STA
tHD;DAT
tHD;STA
REPEATED
START
START
STOP
START
2
Figure 5. I C Interface Timing for Fast and Slow Modes
tFDA
tRDA
REPEATED
START
tSU;DAT
STOP
SDAH
tSU;STA
tRCL1
SCLH
tFCL
tRCL
tSU;STO
tHIGH
tLOW
tHD;STA
tHD;DAT
REPEATED
START
note A
= MCS Current Source Pull-up
= RP Resistor Pull-up
Note A: First rising edge of SCLH after Repeated Start and after each ACK bit.
2
Figure 6. I C Interface Timing for High-Speed Mode
© 2008 Fairchild Semiconductor Corporation
FAN5355 • Rev. 1.0.4
9
www.fairchildsemi.com
FAN5355 — 1A / 0.8A, 3Mhz. Digitally Programmable TinyBuckTM Regulator
Timing Diagrams
Unless otherwise specified, Auto-PWM/NPFM, VIN = 3.6V, TA = 25°C, and recommended components as specified in Table 1.
Efficiency
100%
100%
90%
90%
80%
80%
70%
60%
Auto PWM/NPFM
50%
Forced PWM
Efficiency
Efficiency
70%
40%
Auto PWM/NPFM
60%
Forced PWM
50%
40%
30%
30%
VIN = 3.6 V
VOUT = 1.05 V
20%
VIN = 3.6 V
VOUT = 1.35 V
20%
10%
10%
0%
0%
1
10
100
1
1000
10
100
1000
I LOAD Output Current (mA)
I LOAD Output Current (ma)
Figure 7. Efficiency vs. Load at VOUT = 1.05V
Figure 8. Efficiency vs. Load at VOUT = 1.35V
100%
90%
80%
Auto PWM/NPFM
Efficiency
70%
Forced PWM
60%
50%
40%
VIN = 3.6 V
VOUT = 1.5 V
30%
20%
10%
0%
1
10
100
1000
I LOAD Output Current (ma)
Figure 9. Efficiency vs. Load at VOUT = 1.50V
© 2008 Fairchild Semiconductor Corporation
FAN5355 • Rev. 1.0.4
10
www.fairchildsemi.com
FAN5355 — 1A / 0.8A, 3Mhz. Digitally Programmable TinyBuckTM Regulator
Typical Performance Characteristics
1.064
1.364
1.062
1.362
1.060
1.360
1.058
VOUT (V)
VOUT (V)
Unless otherwise specified, Auto-PWM/NPFM, VIN = 3.6V, TA = 25°C, and recommended components as specified in Table 1.
Auto PWM/NPFM
1.056
Forced PWM
1.054
1.358
Forced PWM
1.354
1.052
1.352
1.050
1.350
1.048
Auto PWM/NPFM
1.356
1.348
1
10
100
1000
1
10
I LOAD Output Current (mA)
100
1000
I LOAD Output Current (mA)
Figure 10. Load Regulation at VOUT = 1.05V
Figure 11. Load Regulation at VOUT = 1.35V
70
6.0
Quiescent Current (μA)
Quiescent Current (μA)
65
60
55
50
VSEL = 1.8V
VSEL = 0V
45
40
35
5.0
VSEL = 1.8V
4.0
VSEL = 0V
3.0
2.0
1.0
-
30
2.0
2.5
3.0
3.5
4.0
4.5
5.0
2.5
5.5
3.0
3.5
VIN Input Voltage (V)
Figure 12. Quiescent Current, ILOAD = 0, EN = 1.8V
4.5
5.0
5.5
Figure 13. Shutdown Current, ILOAD = 0, EN = 0
230
0.10%
210
0.05%
190
0.00%
170
RDS(ON) (mΩ)
Output Voltage (V)
4.0
VIN Input Voltage (V)
-0.05%
-0.10%
-0.15%
VIN = 2.7V
VIN = 3.6V
VIN = 5.5V
-0.20%
150
130
110
P-Channel
N-Channel
90
70
-0.25%
50
-0.30%
30
-40
-20
0
20
40
60
80
2
Temperature (C)
3
3.5
4
4.5
5
5.5
VIN Input Voltage (V)
Figure 14. % VOUT Shift vs. Temperature (Normalized)
© 2008 Fairchild Semiconductor Corporation
FAN5355 • Rev. 1.0.4
2.5
Figure 15. Output Stage RDS(ON) vs. VIN
11
www.fairchildsemi.com
FAN5355 — 1A / 0.8A, 3Mhz. Digitally Programmable TinyBuckTM Regulator
Typical Performance Characteristics
Unless otherwise specified, VIN = 3.6V, VOUT = 1.35V, and load step tR = tF < 100ns.
Load Transient Response
Figure 16. 50mA to 400mA to 50mA, Forced PWM
Figure 17. 50mA to 400mA to 50mA, Auto PWM/NPFM
Figure 18. 400mA to 750mA to 400mA, Auto PWM/NPFM
Figure 19. 0mA to 125mA to 0mA, Auto PWM/NPFM
© 2008 Fairchild Semiconductor Corporation
FAN5355 • Rev. 1.0.4
12
www.fairchildsemi.com
FAN5355 — 1A / 0.8A, 3Mhz. Digitally Programmable TinyBuckTM Regulator
Typical Performance Characteristics (Continued)
Unless otherwise specified, VIN = 3.6V.
VSEL Transitions
Figure 20. Single-Step, RLOAD = 6.2Ω
Figure 21. Single-Step, RLOAD = 6.2Ω
Figure 22. Single-Step, RLOAD = 50Ω
Figure 23. Single-Step, RLOAD = 50Ω
© 2008 Fairchild Semiconductor Corporation
FAN5355 • Rev. 1.0.4
13
www.fairchildsemi.com
FAN5355 — 1A / 0.8A, 3Mhz. Digitally Programmable TinyBuckTM Regulator
Typical Performance Characteristics (Continued)
Unless otherwise specified, VIN = 3.6V.
VSEL Transitions
Figure 24. Single-Step from Forced PWM (MODE1=0),
RLOAD = 50Ω
Figure 25. Single Step, RLOAD = 6.2Ω
Figure 26. Single–Step from Auto PWM/PFM (MODE1=1),
RLOAD = 50Ω
© 2008 Fairchild Semiconductor Corporation
FAN5355 • Rev. 1.0.4
14
www.fairchildsemi.com
FAN5355 — 1A / 0.8A, 3Mhz. Digitally Programmable TinyBuckTM Regulator
Typical Performance Characteristics (Continued)
RLOAD is switched with N-channel MOSFET from VOUT to GND. VIN = 3.6V, initial VOUT = 1.35V, initial ILOAD = 0mA.
Short Circuit and Over-Current Fault Response
Figure 27. Metallic Short Applied at VOUT
Figure 28. Metallic Short Applied at VOUT
Figure 29. RLOAD = 660mΩ
Figure 30. RLOAD = 660mΩ
© 2008 Fairchild Semiconductor Corporation
FAN5355 • Rev. 1.0.4
15
www.fairchildsemi.com
FAN5355 — 1A / 0.8A, 3Mhz. Digitally Programmable TinyBuckTM Regulator
Typical Performance Characteristics (Continued)
Unless otherwise specified, VIN = 3.6V.
Figure 31. SW-Node Jitter (Infinite Persistence),
ILOAD = 200mA
Figure 32. SW-Node Jitter, External Synchronization
(Infinite Persistence), ILOAD = 200mA
PSRR
Attenuation (dB)
70
60
IOUT=500mA
IOUT=150mA
50
IOUT=20mA
40
30
20
10
(10)
0.1
1.0
10.0
100.0
1,000.0
Frequency (KHz)
Figure 34. VIN Ripple Rejection (PSRR)
Figure 33. Soft-Start, RLOAD = 50Ω
© 2008 Fairchild Semiconductor Corporation
FAN5355 • Rev. 1.0.4
16
www.fairchildsemi.com
FAN5355 — 1A / 0.8A, 3Mhz. Digitally Programmable TinyBuckTM Regulator
Typical Performance Characteristics (Continued)
Overview
Power-up, EN, and Soft-start
The FAN5355 is a synchronous buck regulator that typically
operates at 3MHz with moderate to heavy load currents. At
light load currents, the converter operates in power-saving
PFM mode. The regulator automatically transitions between
fixed-frequency PWM and variable-frequency PFM mode to
maintain the highest possible efficiency over the full range of
load current.
All internal circuits remain de-biased and the IC is in a very
low quiescent current state until the following are true:
1.
2.
2
At that point, the IC begins a soft-start cycle, its I C interface is
enabled, and its registers loaded with their default values.
The FAN5355 uses a very fast non-linear control architecture
to achieve excellent transient response with minimum-sized
external components.
During the initial soft-start, VOUT ramps linearly to the setpoint
programmed in the VSEL register selected by the VSEL pin.
The soft start features a fixed output voltage slew rate of
18.75V/ms, and achieves regulation approximately 90μs after
EN rises. PFM mode is enabled during soft-start until the
output is in regulation, regardless of the MODE bit settings.
This allows the regulator to start into a partially charged output
without discharging it; in other words, the regulator does not
allow current to flow from the load back to the battery.
2
The FAN5355 integrates an I C-compatible interface, allowing
transfers up to 3.4Mbps. This communication interface can be
used to:
1.
2.
3.
4.
5.
VIN is above its rising UVLO threshold, and
EN is HIGH.
Dynamically re-program the output voltage in 12.5mV
increments.
Reprogram the mode of operation to enable or disable
PFM mode.
Control voltage transition slew rate.
Control the frequency of operation by synchronizing to an
external clock.
Enable / disable the regulator.
As soon as the output has reached its setpoint, the control
forces PWM mode for about 85μs to allow all internal control
circuits to calibrate.
Symbol Description
tSSDLY
2
For more details, refer to the I C Interface and Register
Description sections.
tREG
Output Voltage Programming
tPOK
Option
tCAL
00, 02,
03
VOUT Equation
VOUT = 0.75 + NVSEL • 12.5mV
VOUT = 0.100 + NVSEL • 25mV
VOUT = 0.675 + (N VSEL − 23 ) • 12.5mV
VOUT = 1.1875 + NVSEL • 12.5mV
25
16 +(VSEL–0.7) X 53
(VSEL–0.1) X 53
11
10
EN
TREG
(2)
VSEL
VOUT
for NVSEL > 23
06
Time from EN to start of
soft-start ramp
VOUT ramp start to Opt 06
regulation
Others
PWROK (CONTROL2[5])
rising from tREG
Regulator stays in PWM
mode during this time
Table 2. Soft-Start Timing (see Figure 35)
(1)
for NVSEL = 0 to 23
07
Value (μs)
(3)
0
where NVSEL is the decimal value of the setting of the VSEL
register that controls VOUT.
TSSDLY
TCAL (FPWM)
TPOK
PWROK
Figure 35. Soft-start Timing
Note:
13. Option 02 maximum voltage is 1.4375V (see Table 3).
© 2008 Fairchild Semiconductor Corporation
FAN5355 • Rev. 1.0.4
17
www.fairchildsemi.com
FAN5355 — 1A / 0.8A, 3Mhz. Digitally Programmable TinyBuckTM Regulator
Circuit Description
00, 03
0.7500
0.7625
0.7750
0.7875
0.8000
0.8125
0.8250
0.8375
0.8500
0.8625
0.8750
0.8875
0.9000
0.9125
0.9250
0.9375
0.9500
0.9625
0.9750
0.9875
1.0000
1.0125
1.0250
1.0375
1.0500
1.0625
1.0750
1.0875
1.1000
1.1125
1.1250
1.1375
1.1500
1.1625
1.1750
1.1875
1.2000
1.2125
1.2250
1.2375
1.2500
1.2625
1.2750
1.2875
1.3000
1.3125
1.3250
1.3375
1.3500
1.3625
1.3750
1.3875
1.4000
1.4125
1.4250
1.4375
1.4500
1.4625
1.4750
1.4875
1.5000
1.5125
1.5250
1.5375
VOUT
02
0.7500
0.7625
0.7750
0.7875
0.8000
0.8125
0.8250
0.8375
0.8500
0.8625
0.8750
0.8875
0.9000
0.9125
0.9250
0.9375
0.9500
0.9625
0.9750
0.9875
1.0000
1.0125
1.0250
1.0375
1.0500
1.0625
1.0750
1.0875
1.1000
1.1125
1.1250
1.1375
1.1500
1.1625
1.1750
1.1875
1.2000
1.2125
1.2250
1.2375
1.2500
1.2625
1.2750
1.2875
1.3000
1.3125
1.3250
1.3375
1.3500
1.3625
1.3750
1.3875
1.4000
1.4125
1.4250
1.4375
1.4375
1.4375
1.4375
1.4375
1.4375
1.4375
1.4375
1.4375
VSEL
Dec Hex
0
00
1
01
2
02
3
03
4
04
5
05
6
06
7
07
8
08
9
09
10 0A
11 0B
12 0C
13 0D
14 0E
15 0F
16 10
17 11
18 12
19 13
20 14
21 15
22 16
23 17
24 18
25 19
26 1A
27 1B
28 1C
29 1D
30 1E
31 1F
32 20
33 21
34 22
35 23
36 24
37 25
38 26
39 27
40 28
41 29
42 2A
43 2B
44 2C
45 2D
46 2E
47 2F
48 30
49 31
50 32
51 33
52 34
53 35
54 36
55 37
56 38
57 39
58 3A
59 3B
60 3C
61 3D
62 3E
63 3F
06
1.1875
1.2000
1.2125
1.2250
1.2375
1.2500
1.2625
1.2750
1.2875
1.3000
1.3125
1.3250
1.3375
1.3500
1.3625
1.3750
1.3875
1.4000
1.4125
1.4250
1.4375
1.4500
1.4625
1.4750
1.4875
1.5000
1.5125
1.5250
1.5375
1.5500
1.5625
1.5750
1.5875
1.6000
1.6125
1.6250
1.6375
1.6500
1.6625
1.6750
1.6875
1.7000
1.7125
1.7250
1.7375
1.7500
1.7625
1.7750
1.7875
1.8000
1.8125
1.8250
1.8375
1.8500
1.8625
1.8750
1.8875
1.9000
1.9125
1.9250
1.9375
1.9500
1.9625
1.9750
Table 3. VSEL vs. VOUT for Options 00, 02, 03, 06
© 2008 Fairchild Semiconductor Corporation
FAN5355 • Rev. 1.0.4
VOUT
0.1000
0.1250
0.1500
0.1750
0.2000
0.2250
0.2500
0.2750
0.3000
0.3250
0.3500
0.3750
0.4000
0.4250
0.4500
0.4750
0.5000
0.5250
0.5500
0.5750
0.6000
0.6250
0.6500
0.6750
0.6875
0.7000
0.7125
0.7250
0.7375
0.7500
0.7625
0.7750
0.7875
0.8000
0.8125
0.8250
0.8375
0.8500
0.8625
0.8750
0.8875
0.9000
0.9125
0.9250
0.9375
0.9500
0.9625
0.9750
0.9875
1.0000
1.0125
1.0250
1.0375
1.0500
1.0625
1.0750
1.0875
1.1000
1.1125
1.1250
1.1375
1.1500
1.1625
1.1750
VSEL
Dec Hex
64 00
65 01
66 02
67 03
68 04
69 05
70 06
71 07
72 08
73 09
74 0A
75 0B
76 0C
77 0D
78 0E
79 0F
80 10
81 11
82 12
83 13
84 14
85 15
86 16
87 17
88 18
89 19
90 1A
91 1B
92 1C
93 1D
94 1E
95 1F
96 20
97 21
98 22
99 23
100 24
101 25
102 26
103 27
104 28
105 29
106 2A
107 2B
108 2C
109 2D
110 2E
111 2F
112 30
113 31
114 32
115 33
116 34
117 35
118 36
119 37
120 38
121 39
122 3A
123 3B
124 3C
125 3D
126 3E
127 3F
VOUT
1.1875
1.2000
1.2125
1.2250
1.2375
1.2500
1.2625
1.2750
1.2875
1.3000
1.3125
1.3250
1.3375
1.3500
1.3625
1.3750
1.3875
1.4000
1.4125
1.4250
1.4375
1.4500
1.4625
1.4750
1.4875
1.5000
1.5125
1.5250
1.5375
1.5500
1.5625
1.5750
1.5875
1.6000
1.6125
1.6250
1.6375
1.6500
1.6625
1.6750
1.6875
1.7000
1.7125
1.7250
1.7375
1.7500
1.7625
1.7750
1.7875
1.8000
1.8125
1.8250
1.8375
1.8500
1.8625
1.8750
1.8875
1.9000
1.9125
1.9250
1.9375
1.9500
1.9625
1.9750
Table 4. VSEL vs. VOUT for Option 07
18
www.fairchildsemi.com
FAN5355 — 1A / 0.8A, 3Mhz. Digitally Programmable TinyBuckTM Regulator
VSEL Value
Dec Binary Hex
0 000000 00
1 000001 01
2 000010 02
3 000011 03
4 000100 04
5 000101 05
6 000110 06
7 000111 07
8 001000 08
9 001001 09
10 001010 0A
11 001011 0B
12 001100 0C
13 001101 0D
14 001110 0E
15 001111 0F
16 010000 10
17 010001 11
18 010010 12
19 010011 13
20 010100 14
21 010101 15
22 010110 16
23 010111 17
24 011000 18
25 011001 19
26 011010 1A
27 011011 1B
28 011100 1C
29 011101 1D
30 011110 1E
31 011111 1F
32 100000 20
33 100001 21
34 100010 22
35 100011 23
36 100100 24
37 100101 25
38 100110 26
39 100111 27
40 101000 28
41 101001 29
42 101010 2A
43 101011 2B
44 101100 2C
45 101101 2D
46 101110 2E
47 101111 2F
48 110000 30
49 110001 31
50 110010 32
51 110011 33
52 110100 34
53 110101 35
54 110110 36
55 110111 37
56 111000 38
57 111001 39
58 111010 3A
59 111011 3B
60 111100 3C
61 111101 3D
62 111110 3E
63 111111 3F
“create demand” for a pulse if no pulse had been required
for 40μs. The minimum frequency limit circuit takes effect
with load currents below about 3.5mA. Above that load
point, the natural PFM period is less than 40μs. This circuit
only activates when ILOAD is greater than ~3.5mA. If the load
remains above 3.5mA, there is no quiescent current penalty
for EPFM mode and there is some accuracy advantage.
The EN_DCDC bit, VSELx[7] can be used to enable the
regulator in conjunction with the EN pin. Setting EN_DCDC
with EN HIGH begins the soft-start sequence described
above.
2
EN_DCDC Bit
EN Pin
IC
REGULATOR
0
1
1
0
0
1
0
1
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
NPFM allows the switching frequency (fSW) to go as low as
required to support the load current. This achieves a lower
quiescent current than EPFM, but sacrifices up to ±15mV of
DC accuracy when compared to EPFM or PWM modes. As
shown in Table 6, EPFM and NPFM modes have the same
frequency when the load is above 4mA. If the load is above
4mA, EPFM is the preferred mode, since it has tighter DC
regulation with the same efficiency.
Table 5. EN_DCDC Behavior
Light-Load (PFM) Operation
EPFM can only be enabled by setting the MODE_CTRL
bits to 11. In versions with MODE_CTRL disabled (see
Table 12), the PFM mode is NPFM.
The FAN5355 offers both a Normal PFM (NPFM) and
Enhanced PFM (EPFM) mode. NPFM is normally used
when the load current is very low and when quiescent
current must be minimized. EPFM provides more accurate
DC regulation and limits the minimum frequency to 25kHz
typical to prevent operation in the audio band.
Mode
IQUIESCENT typical at ILOAD = 0
DC Accuracy
fSW at ILOAD = 0
fSW at ILOAD > 3.5mA
VOUT ripple is identical in both modes (less than 20mV), and
both modes feature very fast response to load transients.
The FAN5355 incorporates a single-pulse, light-load
modulation that ensures:

Smooth transitions between PFM and PWM modes

Single-pulse operation for low ripple
EPFM
NPFM
110μA
Better
25 kHz
> 33 kHz
38μA
Good
to 0 Hz
> 33 kHz
Table 6. PFM Modes Comparison
PFM mode can be disabled by writing to the mode control
bits: CONTROL1[3:0] (see Table 12 for details).
Minimum frequency, of 25kHz typical, to avoid audible
noise (EPFM only)
Switching Frequency Control and
Synchronization
The nominal internal oscillator frequency is 3MHz. The
regulator runs at its internal clock frequency until these
conditions are met:
1. EN_SYNC bit, CONTROL1[5], is set; and
2. A valid frequency appears on the SYNC pin.
Predictable PFM entry and exit currents.
PFM begins after the inductor current has become
discontinuous, crossing zero during the PWM cycle in 32
consecutive cycles. PFM exit occurs when discontinuous
current mode (DCM) operation cannot supply sufficient
current to maintain regulation. During PFM mode, the
inductor current ripple is about 40% higher than in PWM
mode. The load current required to exit PFM mode is
thereby about 20% higher than the load current required to
enter PFM mode, providing sufficient hysteresis to prevent
“mode chatter.”
CONTROL2
FSYNC Valid
PLL_MULT
fSYNC Divider
Min.
Typ.
Max.
00
1
2.25
3.00
4.00
01
2
1.13
1.50
2.00
10
3
0.75
1.00
1.33
11
4
0.56
0.75
1.00
While PWM ripple voltage is typically less than 4mVP-P,
PFM ripple voltage can be up to 30mVP-P during very light
load. To prevent significant undershoot when a load
transient occurs, the initial DC setpoint for the regulator in
PFM mode is set 10mV higher than in PWM mode. This
offset decays to about 5mV after the regulator has been in
PFM mode for ~100μs. The maximum instantaneous
voltage in PFM is 30mV above the setpoint.
If the EN_SYNC is set and SYNC fails validation, the
regulator continues to run at its internal oscillator frequency.
The regulator is functional if fSYNC is valid, as defined in
Table 7, but its performance is compromised if fSYNC is
outside the fSYNC window in the Electrical Specifications.
In Enhanced PFM (EPFM) mode, the regulator maintains a
minimum frequency of 25kHz (typical) to prevent audible
noise being generated by the external components. To
achieve this, the regulator turns on the low-side MOSFET to
When CONTROL1[3:2] = 00 and the VSEL line is LOW, the
converter operates according to the MODE0 bit,
CONTROL1[0], with synchronization disabled regardless of
the state of the EN_SYNC and HW_nSW bits.
© 2008 Fairchild Semiconductor Corporation
FAN5355 • Rev. 1.0.4
Table 7. SYNC Frequency Validation for fOSC(INTERNAL)=3.0MHz
19
www.fairchildsemi.com
FAN5355 — 1A / 0.8A, 3Mhz. Digitally Programmable TinyBuckTM Regulator
Software Enable
setpoint and is typically 7μs for a full-range transition (from
00000 to 11111 for 6-bit DAC options). The PWROK bit,
CONTROL2[5], goes LOW until the transition is complete
and VOUT settled. This typically occurs ~2μs after tV(L-H).
The IC regulates VOUT to one of two setpoint voltages, as
determined by the VSEL pin and the HW_nSW bit.
(14)
VSEL Pin HW_nSW Bit VOUT Setpoint
0
1
x
1
1
0
VSEL0
VSEL1
VSEL1
PFM
It is good practice to reduce the load current before making
positive VSEL transitions. This reduces the time required to
make positive load transitions and avoids current–limitinduced overshoot.
Allowed
Per MODE1
Per MODE1
Table 8. VOUT Setpoint and Mode Control MODE_CTRL,
CONTROL1[3:2] = 00
VHIGH
tV(L-H)
98% VHIGH
Note:
14. Option 07 uses VSELx[6:0] to set VOUT, while all other
options use VSELx[5:0].
VOUT
VLOW
If HW_nSW =0, VOUT transitions are initiated through the
following sequence:
1. Write the new setpoint in VSEL1.
2. Write desired transition rate in DEFSLEW,
CONTROL2[2:0], and set the GO bit in CONTROL2[7].
VSEL
tPOK(L-H)
PWROK
Figure 37. Single-Step VOUT Transition
If HW_nSW =1, VOUT transitions are initiated either by
changing the state of the VSEL pin or by writing to the VSEL
register selected by the VSEL pin.
All positive VOUT transitions inhibit PFM until the transition is
complete, which occurs at the end of tPOK(L-H).
Positive Transitions
Negative Transitions
When transitioning to a higher VOUT, the regulator can
perform the transition using multi-step or single-step mode.
When moving from VSEL=1 to VSEL=0, the regulator
enters PFM mode, regardless of the condition of the SYNC
pin or MODE bits, and remains in PFM until the transition is
completed. Reverse current through the inductor is blocked,
and the PFM minimum frequency control inhibited, until the
new setpoint is reached, at which time the regulator
resumes control using the mode established by
MODE_CTRL. The transition time from VHIGH to VLOW is
controlled by the load current and output capacitance as:
Multi-step Mode:
The internal DAC is stepped at a rate defined by
DEFSLEW, CONTROL2[2:0], ranging from 000 to 110. This
mode minimizes the current required to charge COUT and
thereby minimizes the current drain from the battery when
transitioning. The PWROK bit, CONTROL2[5], remains
LOW until about 1.5μs after the DAC completes its ramp.
t V (H−L ) = COUT •
VHIGH
VHIGH − VLOW
ILOAD
(4)
VHIGH
VOUT
VLOW
VSEL
VOUT
tPOK(L-H)
PWROK
VLOW
VSEL
Figure 36. Multi-step VOUT Transition
PWROK
Single-step Mode:
Used if DEFSLEW, CONTROL2[2:0] = 111. The internal
DAC is immediately set to the higher voltage and the
regulator performs the transition as quickly as its current
limit circuit allows, while avoiding excessive overshoot.
tV(L-H)
tPOK(L-H)
Figure 38. Negative VOUT Transition
Figure 37 shows single-step transition timing. tV(L-H) is the
time it takes the regulator to settle to within 2% of the new
© 2008 Fairchild Semiconductor Corporation
FAN5355 • Rev. 1.0.4
20
www.fairchildsemi.com
FAN5355 — 1A / 0.8A, 3Mhz. Digitally Programmable TinyBuckTM Regulator
Output Voltage Transitions
Slave Address
Current Limit / Auto-Restart
In Table 10, A1 and A0 are according to the Ordering
Information table on page 2.
The regulator includes cycle-by-cycle current limiting, which
prevents the instantaneous inductor current from exceeding
~1350mA.
The IC enters “fault” mode after sustained over-current. If
current limit is asserted for more than 32 consecutive cycles
(about 20μs), the IC returns to shutdown state and remains
in that condition for ~80μs. After that time, the regulator
attempts to restart with a normal soft-start cycle. If the fault
has not cleared, it shuts down ~10μs later.
7
6
1
0
5
4
3
2
1
0
0
1
0
A1
A0
R/ W
2
Table 10. I C Slave Address
Bus Timing
As shown in Figure 39, data is normally transferred when
SCL is LOW. Data is clocked in on the rising edge of SCL.
Typically, data transitions shortly at or after the falling edge
of SCL to allow ample time for the data to set up before the
next SCL rising edge.
If the fault is a short circuit, the initial current limit is ~30% of
the normal current limit, which produces a very small drain
on the system power source.
Data change allowed
Thermal Protection
When the junction temperature of the IC exceeds 150°C,
the device turns off all output MOSFETs and remains in a
low quiescent current state until the die cools to 130°C
before commencing a normal soft-start cycle.
SDA
TH
TSU
Under-Voltage Lockout (UVLO)
SCL
The IC turns off all MOSFETs and remains in a very low
quiescent current state until VIN rises above the UVLO
threshold.
Figure 39. Data Transfer Timing
Each bus transaction begins and ends with SDA and SCL
HIGH. A transaction begins with a “START” condition, which
is defined as SDA transitioning from 1 to 0 with SCL HIGH,
as shown in Figure 40.
I2C Interface
The FAN5355’s serial interface is compatible with standard,
2
fast, and HS mode I C bus specifications. The FAN5355’s
SCL line is an input and its SDA line is a bi-directional opendrain output; it can only pull down the bus when active. The
SDA line only pulls LOW during data reads and when
signaling ACK. All data is shifted in MSB (bit 7) first.
SDA
Figure 40. Start Bit
A transaction ends with a “STOP” condition, which is
defined as SDA transitioning from 0 to 1 with SCL HIGH, as
shown in Figure 41.
Addressing
Slave Releases
FAN5355 has four user-accessible registers:
Address
SDA
7
6
5
4
3
2
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
0
1
0
1
Master Drives
tHD;STO
ACK(0) or
NACK(1)
SCL
Figure 41. Stop Bit
2
Table 9. I C Register Addresses
© 2008 Fairchild Semiconductor Corporation
FAN5355 • Rev. 1.0.4
Slave Address
MS Bit
SCL
SDA and SCL are normally pulled up to a system I/O power
2
supply (VCCIO), as shown in Figure 1. If the I C interface is
not used, SDA and SCL should be tied to AVIN to minimize
quiescent current consumption.
VSEL0
VSEL1
CONTROL1
CONTROL2
THD;STA
During a read from the FAN5355 (Figure 44), the master
issues a “Repeated Start” after sending the register
address, and before resending the slave address. The
“Repeated Start” is a 1 to 0 transition on SDA while SCL is
HIGH, as shown in Figure 42.
21
www.fairchildsemi.com
FAN5355 — 1A / 0.8A, 3Mhz. Digitally Programmable TinyBuckTM Regulator
Protection Features
Read and Write Transactions
The protocols for High-Speed (HS), Low-Speed (LS), and
Fast-Speed (FS) modes are identical, except the bus speed
for HS mode is 3.4MHz. HS mode is entered when the bus
master sends the HS master code 00001XXX after a start
condition. The master code is sent in FS mode (less than
400kHz clock) and slaves do not ACK this transmission.
The following figures outline the sequences for data read and
write. Bus control is signified by the shading of the packet,
The master then generates a repeated start condition
(Figure 42) that causes all slaves on the bus to switch to HS
2
mode. The master then sends I C packets, as described
above, using the HS mode clock rate and timing.
All addresses and data are MSB first.
Slave Drives Bus
SDA
tSU;STA
S
A
A
R
P
tHD;STA
ACK(0) or
NACK(1)
and
.
Symbol Definition
The bus remains in HS mode until a stop bit (Figure 41) is
sent by the master. While in HS mode, packets are
separated by repeated start conditions (Figure 42).
Slave Releases
Master Drives Bus
defined as
SLADDR
MS Bit
START, see Figure 40.
ACK. The slave drives SDA to 0 to acknowledge the
preceding packet.
NACK. The slave sends a 1 to NACK the preceding
packet.
Repeated START, see Figure 42.
STOP, see Figure 41.
2
Table 11. I C Bit Definitions for Figure 43 - Figure 44
SCL
Figure 42. Repeated Start Timing
7 bits
S
Slave Address
0
0
8 bits
0
8 bits
0
A
Reg Addr
A
Data
A
P
Figure 43. Write Transaction
7 bits
S
Slave Address
0
0
8 bits
0
A
Reg Addr
A
7 bits
R
Slave Address
1
0
8 bits
1
A
Data
A
P
Figure 44. Read Transaction
© 2008 Fairchild Semiconductor Corporation
FAN5355 • Rev. 1.0.4
22
www.fairchildsemi.com
FAN5355 — 1A / 0.8A, 3Mhz. Digitally Programmable TinyBuckTM Regulator
High-Speed (HS) Mode
Default Values
Each option of the FAN5355 (see Ordering Information on page 2) has different default values for the some of the register bits.
Table 12 defines both the default values and the bit’s type (as defined in Table 13) for each available option.
VSEL0
VSEL1
Option
7
6
5
4
3
2
1
0
VOUT
Option
7
6
5
4
3
2
1
0
VOUT
00
02
03
07
06
1
1
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
1
1
1
1
0
1
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
1
1.05
1.05
1.00
1.05
1.80
00
02
03
07
06
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
1
1
0
0
0
0
0
0
1
1
0
0
0
0
0
0
0
0
0
0
0
1
1.35
1.20
1.20
1.35
1.80
CONTROL1
CONTROL2
Option
7
6
5
4
3
2
1
0
Option
7
6
5
4
3
2
1
0
00, 02
03
06, 07
1
0
1
0
0
0
0
0
0
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
00, 02
03
06, 07
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
Table 12. Default Values and Bit Types for VSEL and CONTROL Registers
#
#
#
Active bit.
Disabled.
Read-only.
Changing this bit changes the behavior of the converter, as described below.
Converter logic ignores changes made to this bit. Bit can be written to and read-back.
Writing to this bit through I2C does not change the read-back value, nor does it change converter behavior.
Table 13. Bit Type Definitions for Table 12.
© 2008 Fairchild Semiconductor Corporation
FAN5355 • Rev. 1.0.4
23
www.fairchildsemi.com
FAN5355 — 1A / 0.8A, 3Mhz. Digitally Programmable TinyBuckTM Regulator
Register Descriptions
The following table defines the operation of each register bit. Superscript characters define the default state for each option.
0,2,3,6,7
A
Superscripts
signify the default values for options 00, 02, 03, 06, and 07, respectively. signifies the default for all options.
Bit Name
Value Description
VSEL0
7
EN_DCDC
1A
0,2,3,6
Reserved
or DAC6 7
DAC[5:0]
5:0
VSEL1
6
7
0
EN_DCDC
Table
12
0
1A
0,2,3,6
Reserved
or DAC6 7
DAC[5:0]
5:0
CONTROL1
6
7:6
Reserved
5
EN_SYNC
4
HW_nSW
3:2 MODE_CTRL
1
MODE1
0
MODE0
CONTROL2
7
GO
6
OUTPUT_
DISCHARGE
5
PWROK
(read only)
4:3
PLL_MULT
2:0
DEFSLEW
Table
12
Register Address: 00
Device in shutdown regardless of the state of the EN pin. This bit is mirrored in VSEL1. A write to bit 7 in either
register establishes the EN_DCDC value.
Device enabled when EN pin is HIGH, disabled when EN is LOW.
Has no effect in options 00, 02, 03, 06, and defaults to 1. In option 07, it is the MSB of the 7-bit DAC value to set
VOUT.
6-bit DAC value to set VOUT. The six LSBs of the 7-bit value for option 07.
Register Address: 01
Device in shutdown regardless of the state of the EN pin. This bit is mirrored in VSEL0. A write to bit 7 in either
register establishes the EN_DCDC value.
Device enabled when EN pin is HIGH, disabled when EN is LOW.
Has no effect in options 00, 02, 03, 06, and defaults to 1. In option 07, it is the MSB of the 7-bit DAC value to set
VOUT.
6-bit DAC value to set VOUT. The six LSBs of the 7-bit value for option 07.
Register Address: 02
100,2,5,6 Vendor ID bits. Writing to these bits has no effect on regulator operation. These bits can be used to distinguish
between vendors via I2C.
003
A
0
Disables external signal on SYNC from affecting the regulator.
When a valid frequency is detected on SYNC, the regulator synchronizes to it and PFM is disabled, except
1
when MODE = 00, VSEL pin = LOW, and HW_nSW = 1.
0
VOUT is controlled by VSEL1. Voltage transitions occur by writing to the VSEL1, then setting the GO bit.
VOUT is programmed by the VSEL pin. VOUT = VSEL1 when VSEL is HIGH, and VSEL0 when VSEL is LOW.
1A
00A
Operation follows MODE0, MODE1.
01
NPFM with automatically transitions to PWM, regardless of VSEL.
10
PFM disabled (forced PWM), regardless of VSEL.
11
EPFM (FSW(MIN) = 25kHz) with automatically transitions to PWM, regardless of VSEL.
0A
PFM disabled (forced PWM) when regulator output is controlled by VSEL1.
1
NPFM with automatic transitions to PWM when regulator output is controlled by VSEL1.
NPFM with automatic transitions to PWM when VSEL is LOW. Changing this bit has no effect on the operation
0A
of the regulator.
1
Register Address: 03
0A
This bit has no effect when HW_nSW = 1. At the end of a VOUT transition, this bit is reset to 0.
1
Starts a VOUT transition if HW_nSW = 0.
0A
When the regulator is disabled, VOUT is not discharged.
1
When the regulator is disabled, VOUT discharges through an internal pull-down.
0
VOUT is not in regulation or is in current limit.
1
VOUT is in regulation.
00A
fSW = fSYNC when synchronization is enabled.
01
fSW = 2 X fSYNC when synchronization is enabled.
10
fSW = 3 X fSYNC when synchronization is enabled.
11
fSW = 4 X fSYNC when synchronization is enabled.
000
VOUT slews at 0.15mV/μs during positive VOUT transitions.
001
VOUT slews at 0.30mV/μs during positive VOUT transitions.
010
VOUT slews at 0.60mV/μs during positive VOUT transitions.
011
VOUT slews at 1.20mV/μs during positive VOUT transitions.
100
VOUT slews at 2.40mV/μs during positive VOUT transitions.
101
VOUT slews at 4.80mV/μs during positive VOUT transitions.
110
VOUT slews at 9.60mV/μs during positive VOUT transitions.
111A Positive VOUT transitions use single-step mode (see Figure 37).
© 2008 Fairchild Semiconductor Corporation
FAN5355 • Rev. 1.0.4
24
www.fairchildsemi.com
FAN5355 — 1A / 0.8A, 3Mhz. Digitally Programmable TinyBuckTM Regulator
Bit Definitions
BALL A1
INDEX AREA
A
E
(Ø0.25)
Cu PAD
B
0.03 C
2X
0.50
1.00
A1
(Ø0.35)
SOLDER MASK
OPENING
0.50
D
0.03 C
TOP VIEW
RECOMMENDED LAND PATTERN (NSMD)
2X
0.06 C
0.05 C
D
0.332±0.018
0.625
0.539
0.250±0.025
SEATING PLANE
C
SIDE VIEWS
(X)+/-.018
0.005
0.50
C A B
A. NO JEDEC REGISTRATION APPLIES
B. DIMENSIONS ARE IN MILLIMETERS.
C. DIMENSIONS AND TOLERANCES PER
ASME Y14.5M, 1994
D DATUM C, THE SEATING PLANE, IS DEFINED
BY THE SPHERICAL CROWNS OF THE BALLS.
12 X Ø0.315 +/- .025
D
C
0.50
B
A
(Y)+/-.018
F FOR DIMENSIONS D, E, X, AND Y SEE
1 2
PRODUCT DATASHEET.
F. BALL COMPOSITION: Sn95.5Ag3.9Cu0.6
SAC405 ALLOY
G. DRAWING FILENAME: MKT-UC012AArev2
3
BOTTOM VIEW
Figure 45. 12-Bump WLCSP, 0.5mm Pitch
Product-Specific Dimensions
Product
D
E
X
Y
FAN5355UC
2.230 +/-0.030
1.460 +/-0.030
0.230
0.365
Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without
notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most
recent revision. Package specifications do not expand the terms of Fairchild’s worldwide terms and conditions, specifically the warranty
therein, which covers Fairchild products.
Always visit Fairchild Semiconductor’s online packaging area for the most recent package drawings:
http://www.fairchildsemi.com/packaging/
© 2008 Fairchild Semiconductor Corporation
FAN5355 • Rev. 1.0.4
25
www.fairchildsemi.com
FAN5355 — 1A / 0.8A, 3Mhz. Digitally Programmable TinyBuckTM Regulator
Physical Dimensions
3.0
0.10 C
10
A
2X
6
1.55
2.00
3.10
2.33
0.78
0.55
B
2.25
2.40
2.00
3.0
0.10 C
2X
TOP VIEW
0.8 MAX
1
0.50
0.25
5
RECOMMENDED LAND PATTERN
(0.20)
0.05
0.00
0.02
D
0.10 C
0.08 C
0.23
C
SIDE VIEW
S E A TING
P LA NE
(3.00±0.10)
2.40
PIN #1 IDENT
(0.38)
5
1
1.40 (3.00±0.10)
E
0.55±0.10
10
0.30
0.20
0.5
6
2.0
0.10
0.05
C A B
C
BOTTOM VIEW
A. CONFORMS TO JEDEC REGISTRATION MO-229,
VARIATION WEED-5 EXCEPT WHERE NOTED
B. DIMENSIONS ARE IN MILLIMETERS.
C. DIMENSIONS AND TOLERANCES PER
ASME Y14.5M, 1994
D. LAND PATTERN DIMENSIONS ARE NOMINAL
REFERENCE VALUES ONLY
E. NOT COMPLIANT
MLP10ArevB
Figure 46. 10-pin, 3x3mm Molded Leadless Package (MLP)
Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without
notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most
recent revision. Package specifications do not expand the terms of Fairchild’s worldwide terms and conditions, specifically the warranty
therein, which covers Fairchild products.
Always visit Fairchild Semiconductor’s online packaging area for the most recent package drawings:
http://www.fairchildsemi.com/packaging/
© 2008 Fairchild Semiconductor Corporation
FAN5355 • Rev. 1.0.4
26
www.fairchildsemi.com
FAN5355 — 1A / 0.8A, 3Mhz. Digitally Programmable TinyBuckTM Regulator
Physical Dimensions
FAN5355 — 1A / 0.8A, 3Mhz. Digitally Programmable TinyBuckTM Regulator
© 2008 Fairchild Semiconductor Corporation
FAN5355 • Rev. 1.0.4
27
www.fairchildsemi.com

Open as PDF

Similar pages