Current Transducer LTC 600-T IPN = 500 A For the electronic measurement of currents : DC, AC, pulsed..., with a galvanic isolation between the primary circuit (high power) and the secondary circuit (electronic circuit). Electrical data IPN IP ÎP RM Primary nominal r.m.s. current Primary current, measuring range @ 24 V Max overload not measurable Measuring resistance with ± 15 V with ± 24 V @ ± 500 A max @ ± 1200 A max @ ± 500 A max @ ± 1500 A max ISN KN VC IC Vd Secondary nominal r.m.s. current Conversion ratio Supply voltage (± 5 %) Current consumption R.m.s. voltage for AC isolation test, 50 Hz, 1 mn Ve R.m.s. voltage for partial discharge extinction 500 A 0 .. ± 1500 A 10 / 10 kA/ms RM min RM max 0 0 0 0 70 5 150 20 100 1 : 5000 ± 15 .. 24 < 30 (@±24V) + IS 13.4 1) 1.5 2) > 2.8 Ω Ω Ω Ω mA V mA kV kV kV Accuracy - Dynamic performance data XG Overall accuracy @ IPN , TA = 25°C @ IPN , TA = - 40°C .. + 85°C Linearity error < ± 0.7 < ± 1.6 < 0.1 IO IOT Offset current @ IP = 0, TA = 25°C Thermal drift of IO Max ± 0.5 ±1 tr di/dt f Response time 3) @ 90 % of IPN di/dt accurately followed Frequency bandwidth (- 1 dB) ε L - 40°C .. + 85°C <1 > 100 DC .. 100 % % % mA mA µs A/µs kHz Notes : Ambient operating temperature Ambient storage temperature Secondary coil resistance @ TA = 85°C Mass Standards 1) 2) 3) • Closed loop (compensated) current transducer using the Hall effect • Insulated plastic case recognized according to UL 94-V0 • Railway equipment. Advantages • • • • • • • Excellent accuracy Very good linearity Low temperature drift Optimized response time Wide frequency bandwidth No insertion losses High immunity to external interference • Current overload capability. Applications • AC variable speed drives and servo motor drives • Static converters for DC motor drives • Battery supplied applications • Uninterruptible Power Supplies (UPS) • Switched Mode Power Supplies General data TA TS RS m Features (SMPS) - 40 .. + 85 °C - 45 .. + 90 °C 44 Ω 1270 g EN 50155 (01.12.20) • Power supplies for welding applications. Between primary and secondary + shield Between secondary and shield With a di/dt of 100 A/µs. 040430/2 LEM Components w w w.lem.com Dimensions LTC 600-T (in mm. 1 mm = 0.0394 inch) Front view Left view Secondary terminals Terminal Terminal Terminal Terminal + M E : : : : supply voltage + 15 .. 24 V measure supply voltage - 15 .. 24 V shield Connection or Top view Mechanical characteristics • General tolerance • Fixing the transducer Recommended fastening torque • Connection of secondary Recommended fastening torque Remarks ± 1 mm 2 holes ∅ 13 mm or by the primary bar 2 steel screws M12 24.5 Nm M5 threaded studs 2.2 Nm or 1.62 Lb.-Ft. Faston 6.3 x 0.8 mm • IS is positive when IP flows in the direction of the arrow. • Temperature of the primary conductor should not exceed 100°C. • This is a standard model. For different versions (supply voltages, turns ratios, unidirectional measurements...), please contact us. LEM reserves the right to carry out modifications on its transducers, in order to improve them, without previous notice.