FPF1007-FPF1009 IntelliMAX™ Advanced Load Products tm Features General Description 1.2 to 5.5V Input Voltage Range The FPF1007/8/9 are low RDS P-Channel MOSFET load switches offered in a selection of 10µs, 80µs, and 1ms slew rate turn-on options for transient/in-rush current control. To support trends in mobile application requirements the minimum operating input voltage has been reduced down to 1.2V, the input current leakage has been minimized to extend battery life, and the ESD-protection has been designed to withstand a minimum of 8KV (HBM) and 2KV(CDM). Typical RON = 30 mΩ @ VIN = 5.5V Typical RON = 40 mΩ @ VIN = 3.3V Fixed Three Different Turn-on Rise-time 10µs/80µs/1ms Low < 10µA @ VIN = 3.3V Quiescent Current Internal ON Pin Pull Down Output Discharge Function ESD Protection above 8000V HBM and 2000V CDM The switch is controlled by an active-high logic input (ON pin) allowing it to interface directly with a low voltage control signal. An internal ON pin pull down resistor protects against an unintentional device turn-on while in the initial state. An On-chip pull-down resistor on the output is enabled when the switch is turned-off and provides a quick and robust discharge of the output load. RoHS Compliant Applications PDAs Cell Phones GPS Devices MP3 Players Digital Cameras Peripheral Ports Hot Swap Supplies Notebook Computer Pin 1 BOTTOM TOP Ordering Information Part Switch RON @ 5.5V [Typ.] Rise Time [Typ.] Output Discharge [Typ.] ON Pin Activity FPF1007 30mΩ, PMOS 10µs 60Ω Active HI FPF1008 30mΩ, PMOS 80µs 60Ω Active HI FPF1009 30mΩ, PMOS 1ms 60Ω Active HI ©2008 Fairchild Semiconductor Corporation FPF1007-FPF1009 Rev. B1 1 www.fairchildsemi.com FPF1007-FPF1009 IntelliMAX™ Advanced Load Products January 2008 IN OUT FPF1007-FPF1009 1.2V~5.5V OFF ON COUT ON RL GND CIN ≥ 0.1µF Functional Block Diagram VIN Turn-ON Slew Rate Controlled Driver CONTROL LOGIC ON VOUT ESD Protection Output Discharge FPF1007-FPF1009 GND FPF1007-FPF1009 Rev. B1 2 www.fairchildsemi.com FPF1007-FPF1009 IntelliMAX™ Advanced Load Products Typical Application Circuit FPF1007-FPF1009 IntelliMAX™ Advanced Load Products Pin Configuration GND 6 1 ON VOUT 5 2 VIN VOUT 4 3 VIN MicroFET 2x2 6L BOTTOM VIEW Pin Description Pin Name 4, 5 VOUT 2, 3 VIN 6 GND 1 ON Function Switch Output: Output of the power switch Supply Input: Input to the power switch and the supply voltage for the IC Ground ON/OFF Control Input Absolute Maximum Ratings Parameter Min. VIN, VOUT, ON to GND -0.3 Maximum Continuous Switch Current Power Dissipation @ TA = 25°C (Note 1) Max. Unit 6 V 1.5 A 1.2 W Storage Junction Temperature -65 150 °C Operating Temperature Range -40 85 °C 86 °C/W Thermal Resistance, Junction to Ambient Electrostatic Discharge Protection HBM 8000 V CDM 2000 V Recommended Operating Range Parameter Min. Max. Unit VIN 1.2 5.5 V Ambient Operating Temperature, TA -40 85 °C Electrical Characteristics VIN = 1.2 to 5.5V, TA = -40 to +85°C unless otherwise noted. Typical values are at VIN = 3.3V and TA = 25°C. Parameter Symbol Conditions Min. Typ. Max. Units Basic Operation Operating Voltage Quiescent Current IQ Off Supply Current Off Switch Current FPF1007-FPF1009 Rev. B1 1.2 VIN IOUT = 0mA, VIN = 3.3V, VON = Enabled 5.5 8 V µA IOUT = 0mA, VIN = 5.5V, VON = Enabled 15 IQ(off) VON = GND, VOUT = OPEN 1 µA ISD(off) VON = GND, VOUT = GND 1 µA 3 0.1 www.fairchildsemi.com VIN = 1.2 to 5.5V, TA = -40 to +85°C unless otherwise noted. Typical values are at VIN = 3.3V and TA = 25°C. Parameter Symbol On-Resistance RON Conditions Min. Typ. Max. Units VIN = 5.5V, IOUT = 200mA, TA = 25°C 30 40 VIN = 3.3V, IOUT = 200mA, TA = 25°C 40 55 VIN = 1.5V, IOUT = 200mA, TA = 25°C 100 130 175 250 VIN = 1.2V, IOUT = 200mA, TA = 25°C VIN = 3.3V, IOUT = 200mA, TA = -40°C to +85°C Output Pull Down Resistance RPD VIN = 3.3V, VON = 0V, TA = 25°C ON Input Logic Low Voltage VIL VIN = 1.2V to 5.5V ON Input Logic High Voltage VIH 20 mΩ 65 60 Ω 0.4 V VIN = 1.2V to 5.5V 1 ON Input Leakage (On) VON = VIN = 5.5V -1 10 µA V ON Input Leakage (Off) VON = GND -1 1 µA Dynamic FPF1007 Turn On Rise Time 12 µs VIN = 3.3V, RL = 500Ω, RL_CHIP = 60Ω, 10 µs COUT = 0.1µF, TA = 25°C 40 µs 15 µs tON tR Turn Off tOFF Fall Time tF FPF1008 Turn On Rise Time tON tR Turn Off tOFF Fall Time tF 125 µs VIN = 3.3V, RL = 500Ω, RL_CHIP = 60Ω, 80 µs COUT = 0.1µF, TA = 25°C 40 µs 15 µs FPF1009 Turn On Rise Time tON tR Turn Off tOFF Fall Time tF 2 ms VIN = 3.3V, RL = 500Ω, RL_CHIP = 60Ω, 1 ms COUT = 0.1µF, TA = 25°C 40 µs 15 µs Note 1: Package power dissipation on 1square inch pad, 2 oz. copper board. FPF1007-FPF1009 Rev. B1 4 www.fairchildsemi.com FPF1007-FPF1009 IntelliMAX™ Advanced Load Products Electrical Characteristics Cont. 1.0 12 0.9 SUPPLY CURRENT ( uA) SUPPLY CURRENT ( uA) 14 VON = VIN 10 8 6 4 2 VON = 0V 0.8 0.7 VIN = 5.5V 0.6 VIN = 3.3V 0.5 0.4 VIN = 1.2V 0.3 VON = 0V 0.2 0 1 2 3 4 5 -40 6 -15 60 85 Figure 2. Quiescent Current vs. Temperature 0.80 14 VON = VIN VON SUPPLY VOLTAGE ( V) VIN = 5.5V 12 10 VIN = 3.3V 8 6 VIN = 1.2V 4 2 0 -40 0.75 VONH(VIH) 0.70 VONL(VIL) 0.65 0.60 0.55 0.50 -15 10 35 60 85 1 2 3 o 0.90 0.80 0.85 VON SUPPLY VOLTAGE ( V) 0.85 0.75 VIN = 5.5V 0.70 0.65 VIN = 3.3V VIN = 1.2V 5 6 Figure 4. VON Voltage vs. Input Voltage Figure 3. Quiescent Current vs. Temperature 0.60 4 VIN, SUPPLY VOLTAGE (V) TJ, JUNCTION TEMPERATURE ( C) VON SUPPLY VOLTAGE ( V) 35 o Figure 1. Quiescent Current vs. Input Voltage SUPPLY CURRENT ( uA) 10 TJ, JUNCTION TEMPERATURE ( C) SUPPLY VOLTAGE (V) 0.55 0.80 VIN=5.5V 0.75 VIN=3.3V 0.70 VIN=1.2V 0.65 0.60 0.50 -40 -15 10 35 60 -40 85 Figure 5. VON Low Voltage vs. Temperature FPF1007-FPF1009 Rev. B1 -15 10 35 60 85 TJ, JUNCTION TEMPERATURE (oC) o TJ, JUNCTION TEMPERATURE ( C) Figure 6. VON High Voltage vs. Temperature 5 www.fairchildsemi.com FPF1007-FPF1009 IntelliMAX™ Advanced Load Products Typical Characteristics 240 6.5 210 VON = 5.5V 5.5 180 4.5 RON(mOhms) ON PIN CURRENT ( uA) 7.5 3.5 2.5 1.5 150 120 90 60 VON = 0V 0.5 85°C 25°C 30 -40°C -0.5 0 -40 -15 10 35 60 85 1 2 3 TJ, JUNCTION TEMPERATURE (oC) 100 6 1000 FPF1007 TOFF 10 FPF1008 TURN-ON/OFF TIMES ( uS) TURN-ON/OFF TIMES (uS) 5 Figure 8. RON vs. VIN Figure 7. On Pin Current vs. Temperature TON VIN = 3.3V RL = 500 Ohms COUT = 0.1uF 1 0.1 -40 -15 10 35 60 VIN = 3.3V RL = 500 Ohms COUT = 0.1uF TON 100 TOFF 10 -40 85 -15 o 10 35 60 85 o TJ, JUNCTION TEMPERATURE ( C) TJ, JUNCTION TEMPERATURE ( C) Figure 9. FPF1007 TON / TOFF vs. Temperature Figure 10. FPF1008 TON / TOFF vs. Temperature 100 FPF1009 FPF1007 TON RISE / FALL TIMES ( uS) TURN-ON/OFF TIMES ( uS) 4 VIN, SUPPLY VOLTAGE (V) 1000 VIN = 3.3V RL = 500 Ohms COUT = 0.1uF TOFF 10 -40 -15 10 35 60 10 TRISE VIN = 3.3V RL = 500 Ohms COUT = 0.1uF 1 -40 85 TJ, JUNCTION TEMPERATURE (oC) -15 10 35 60 85 o TJ, JUNCTION TEMPERATURE ( C) Figure 11. FPF1009 TON / TOFF vs. Temperature FPF1007-FPF1009 Rev. B1 TFALL Figure 12. FPF1007 TRISE / TFALL vs. Temperature 6 www.fairchildsemi.com FPF1007-FPF1009 IntelliMAX™ Advanced Load Products Typical Characteristics 1000 10000 FPF1009 RISE / FALL TIMES ( uS) RISE / FALL TIMES ( uS) FPF1008 TRISE 100 TFALL 10 VIN = 3.3V RL = 500 Ohms COUT = 0.1uF 1 -40 -15 10 35 60 TRISE 1000 VIN = 3.3V RL = 500 Ohms COUT = 0.1uF 100 TFALL 10 1 -40 85 -15 o VIN 2V/div IOUT 50mA/div VOUT 2V/div VOUT 2V/div 50µs/div 50µs/div Figure 15. FPF1007 Turn ON Response Figure 16. FPF1007 Turn OFF Response Load current is discharged through On-chip output discharge resistor. VON = 3.3V VIN = 3.3V CIN = 1µF COUT = 1µF RL = 10Ω VIN 2V/div VON 2V/div VON = 3.3V VIN = 3.3V CIN = 1µF COUT = 1µF RL = 10Ω VIN 2V/div IOUT 200mA/div IOUT 200mA/div VOUT 2V/div VOUT 2V/div 50µs/div 50µs/div Figure 17. FPF1007 Turn ON Response (COUT = 1µF) FPF1007-FPF1009 Rev. B1 85 VON = 3.3V VIN = 3.3V CIN = 1µF COUT = 0.1µF RL = 499Ω VON 2V/div IOUT 10mA/div VON 2V/div 60 Figure 14. FPF1009 TRISE / TFALL vs. Temperature VON = 3.3V VIN = 3.3V CIN = 1µF COUT = 0.1µF RL = 499Ω VIN 2V/div 35 TJ, JUNCTION TEMPERATURE ( C) Figure 13. FPF1008 TRISE / TFALL vs. Temperature VON 2V/div 10 o TJ, JUNCTION TEMPERATURE ( C) Figure 18. FPF1007 Turn OFF Response 7 www.fairchildsemi.com FPF1007-FPF1009 IntelliMAX™ Advanced Load Products Typical Characteristics VON = 3.3V VIN = 3.3V CIN = 1µF COUT = 0.47µF RL = 499Ω VON 2V/div VIN 2V/div VON = 3.3V VIN = 3.3V CIN = 1µF COUT = 0.47µF RL = 499Ω VON 2V/div VIN 2V/div IOUT 10mA/div IOUT 50mA/div VOUT 2V/div VOUT 2V/div 100µs/div 500µs/div Figure 19. FPF1008 Turn ON Response Figure 20. FPF1008 Turn OFF Response Load current is discharged through On-chip output discharge resistor. VON = 3.3V VIN = 3.3V CIN = 1µF COUT = 4.7µF RL = 10Ω VON 2V/div VIN 2V/div VON = 3.3V VIN = 3.3V CIN = 1µF COUT = 4.7µF RL = 10Ω VON 2V/div VIN 2V/div IOUT 500mA/div IOUT 10mA/div VOUT 2V/div VOUT 2V/div 100µs/div 100µs/div Figure 21. FPF1008 Turn ON Response (COUT = 4.7µF) Figure 22. FPF1008 Turn OFF Response VIN 2V/div VIN 2V/div IOUT 500mA/div IOUT 10mA/div VOUT 2V/div VOUT 2V/div 2ms/div 500µs/div Figure 23. FPF1008 Turn ON Response (COUT = 10µF) FPF1007-FPF1009 Rev. B1 VON = 3.3V VIN = 3.3V CIN = 1µF COUT = 0.47µF RL = 499Ω VON 2V/div VON = 3.3V VIN = 3.3V CIN = 1µF COUT = 10µF RL = 10Ω VON 2V/div Figure 24. FPF1009 Turn ON Response 8 www.fairchildsemi.com FPF1007-FPF1009 IntelliMAX™ Advanced Load Products Typical Characteristics VON = 3.3V VIN = 3.3V CIN = 1µF COUT = 0.47µF RL = 499Ω VON 2V/div VIN 2V/div VON = 3.3V VIN = 3.3V CIN = 1µF COUT = 47µF RL = 10Ω VON 2V/div VIN 2V/div IOUT 50mA/div IOUT 500mA/div VOUT 2V/div VOUT 2V/div 500µs/div 2ms/div Figure 26. FPF1009 Turn ON Response (COUT = 47µF) Figure 25. FPF1009 Turn OFF Response Load current is discharged through On-chip output discharge resistor. VON = 3.3V VIN = 3.3V CIN = 1µF COUT = 47µF RL = 10Ω VON 2V/div VIN 2V/div VON 2V/div VON = 3.3V VIN = 5V CIN = 1µF COUT = 100µF RL = 10Ω VIN 2V/div IOUT 500mA/div IOUT 500mA/div VOUT 2V/div VOUT 2V/div 2ms/div 2ms/div Figure 27. FPF1009 Turn OFF Response Figure 28. FPF1009 Turn ON Response (COUT = 100µF, VIN = 5V) Timing Diagram 90% VOUT 90% 10% where: tON tOFF tdon tdoff tR tF tON tOFF 10% tF tR 3.3V 50% 50% VON = = = = = = = = Turn ON Time Turn OFF Time Turn ON Delay Time Turn OFF Delay Time Rise Time VOUT Fall Time tR + tdon tF + tdoff TF 90% 10% VOUT tdon FPF1007-FPF1009 Rev. B1 tdoff 9 www.fairchildsemi.com FPF1007-FPF1009 IntelliMAX™ Advanced Load Products Typical Characteristics FPF1007-FPF1009 IntelliMAX™ Advanced Load Products Dimensional Outline and Pad Layout FPF1007-FPF1009 Rev. B1 10 www.fairchildsemi.com The following are registered and unregistered trademarks and service marks Fairchild Semiconductor owns or is authorized to use and is not intended to be an exhaustive list of all such trademarks. ACEx® Build it Now™ CorePLUS™ CROSSVOLT™ CTL™ Current Transfer Logic™ EcoSPARK® EZSWITCH™ * FPS™ FRFET® Global Power ResourceSM Green FPS™ Green FPS™ e-Series™ GTO™ i-Lo™ IntelliMAX™ ISOPLANAR™ MegaBuck™ MICROCOUPLER™ MicroFET™ MicroPak™ MillerDrive™ Motion-SPM™ OPTOLOGIC® OPTOPLANAR® ™ Fairchild® Fairchild Semiconductor® FACT Quiet Series™ FACT® FAST® FastvCore™ FlashWriter® * PDP-SPM™ Power220® POWEREDGE® Power-SPM™ PowerTrench® Programmable Active Droop™ QFET® QS™ QT Optoelectronics™ Quiet Series™ RapidConfigure™ SMART START™ SPM® STEALTH™ SuperFET™ SuperSOT™-3 SuperSOT™-6 SuperSOT™-8 ® SupreMOS™ SyncFET™ ® The Power Franchise® TinyBoost™ TinyBuck™ TinyLogic® TINYOPTO™ TinyPower™ TinyPWM™ TinyWire™ µSerDes™ UHC® Ultra FRFET™ UniFET™ VCX™ * EZSWITCH™ and FlashWriter® are trademarks of System General Corporation, used under license by Fairchild Semiconducntor. DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION, OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. THESE SPECIFICATIONS DO NOT EXPAND THE TERMS OF FAIRCHILD’S WORLDWIDE TERMS AND CONDITIONS, SPECIFICALLY THE WARRANTY THEREIN, WHICH COVERS THESE PRODUCTS. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. 2. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significant injury to the user. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. PRODUCT STATUS DEFINITIONS Definition of Terms Datasheet Identification Product Status Definition Advance Information Formative or In Design This datasheet contains the design specifications for product development. Specifications may change in any manner without notice. Preliminary First Production This datasheet contains preliminary data; supplementary data will be published at a later date. Fairchild Semiconductor reserves the right to make changes at any time without notice to improve design. No Identification Needed Full Production This datasheet contains final specifications. Fairchild Semiconductor reserves the right to make changes at any time without notice to improve design. Obsolete Not In Production This datasheet contains specifications on a product that has been discontinued by Fairchild semiconductor. The datasheet is printed for reference information only. Rev. I33 FPF1007-FPF1009 Rev. B1 11 www.fairchildsemi.com FPF1007-FPF1009 IntelliMAX™ Advanced Load Products TRADEMARKS