Approve Sheet Part Number: GBJ8A~GBJ8K DATA SHEET GBJ8A~GBJ8K GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER VOLTAGE - 50 to 800 Volts CURRENT - 8.0 Amperes GBJ Unit: inch ( mm ) FEATURES 0.146(3.7) 0.129(3.3) • High temperature soldering guaranteed: 0.578(14.7) 0.603(15.3) • Surge overload rating: 200Amperes peak 260°C/10 seconds/.375"(9.5mm) lead length at 5 lbs. (2.3kg) tension MECHANICAL DATA molded plastic technique Terminals: Leads solderable per MIL-STD-202, Method 208 0.115(2.9) 0.098(2.5) 0.669(17.0) 0.709(18.0) Case: Reliable low cost construction utilizing 0.087(2.2) 0.070(1.8) 0.044(1.1) 0.035(0.9) Mounting position: Any Mounting torque: 5 in. lb. Max. 0.304(7.7) 0.288(7.3) 0.304(7.7) 0.288(7.3) 0.304(7.7) 0.288(7.3) Weight: 0.15 ounce, 4.0 grams 0.150(3.8) 0.133(3.4) 0.382(9.7) 0.366(9.3) • Reliable low cost construction utilizing molded plastic technique 0.122(3.1) 0.142(3.6) • Ideal for printed circuit board 0.189(4.8) 0.173(4.4) 0.996(25.3) 0.972(24.7) C 0.118 (3.0) • Plastic material has Underwriters Laboratory Flammability Classification 94V-O 0.032(0.8) 0.024(0.6) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating at 25°Cambient temperature unless otherwise specified. Resistive or inductive load, 60Hz. For Capacitive load derate current by 20%. GBJ8A GBJ8B GBJ8D GBJ8G GBJ8J GBJ8K UNIT Maximum Recurrent Peak Reverse Voltage 50 100 200 400 600 800 V Maximum RMS Input Voltage 35 70 140 280 420 560 V Maximum DC Blocking Voltage 50 100 200 400 600 800 V Maximum Average Forward TC=100°C 8.0 TA= 45°C 6.0 Rectified Output Current A I2t Rating for fusing ( t<8.3ms) 166 A2sec Peak Forward Surge Current single sine-wave superimposed on rated load (JEDEC method) 200 Apk Maximum Instantaneous Forward Voltage Drop per element at 8.0A 1.0 Vpk Maximum Reverse Leakage at rated TA=25° 5 CDc Blocking Voltage per element TC=100°C 500 µA µA Typical Thermal Resistance per leg(Note 2) RθJA 18.0 °C / W Typical Thermal Resistance per leg(Note 3) RθJC 3.0 °C / W -55 to +150 °C Operating and Storage Temperature Range, TJ,TSTG NOTES: 1. Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum heat transfer with #6 screw. 2. Units Mounted in free air, no heatsink, P.C.B at 0.375"(9.5mm) lead length with 0.5 x 0.5"(12 x 12mm)copper pads. 3. Units Mounted on a 3.0 x 3.0" x 0.11" thick ( 7.5 x 7.5 x 0.3cm) AL plate. PAGE . 1 Approve Sheet Part Number: GBJ8A~GBJ8K INSTANTANEOUS FORWARD CURRENT, AMPERES AVERAGE FORWARD CURRENT AMPERES 8.0 HEAT-SINK MOUNTING,TC (4 4 0.15) INCH COPPER PLATE 6.0 4.0 2.0 MOUNTED ON PC BOARD. TA 0.5"(12.7mm) LEAD LENGTH 60Hz RESISTIVE OR INDUCTIVE LOAD 0 0 50 100 100 40 20 10 4.0 1.0 0.4 0.2 0.1 0.7 150 O TEMPERATURE C FPRWARD SURGE CURRENT, AMPERES pk (HALF SINE-WAVE) INSTANTANEOUS REVERSE CURRENT, MICROAMPERES 10 O T C =100 C 1.0 0.1 O T A =25 C 0.01 20 40 60 80 100 120 0.8 0.9 1.0 1.1 1.2 1.3 1.4 INSTANTANEOUS FORWARD VOLTAGE, VOLTS ig. 1- DERATING CURVE FOR OUTPUT RECTIFIED CURRENT 0 TJ=25OC Pulse Width=300 S 1% DULY Cycle 2.0 140 PERCENT OF PEAK REVERSE VOLTAGE Fig. 3- TYPICAL REAK REVERSE CHARACTERISTICS Fig. 2- TYPICAL INSTANTANEOUS FORWARD CHARACTERISITCS PER ELEMENT 200 160 120 80 O T A =105 C 40 0 1 2 6 10 20 40 60 100 NO. OF CYCLES AT 60Hz Fig. 4- MAXIMUM NON-REPETITEVE PEAK FORWARD SURGE CURRENT CAPACITANCE, pF 400 100 O Tj=25 C f=1.0MHz Vsig=50mVp-p 50 10 1 5 10 50 100 REVERSE VOLTAGE, VOLTS Fig 5 TYPICL JUNCTION CAPACITANCE PER ELEMENT PAGE . 2