CURRENT 6.0 Amperes VOLTAGE 50 to 1000 Volts HER601 THRU HER608 Features · Plastic package has Underwriters Laboratory Flammability Classification 94V-0 · Low forward voltage drop · High current capability · High reliability · Low power loss, high effciency · High surge current capability · High speed switching · Low leakage P-6 0.360(9.1) 0.340(8.6) DIA. 1.0(25.4) MIN. 0.360(9.1) 0.340(8.6) Mechanical Data · Case : P-6 molded plastic body · Epoxy : UL94V-0 rate flame retardant · Lead : Plated axial lead solderable per MIL-STD-750, method 2026 · Polarity : Color band denotes cathode end · Mounting Position : Any · Weight : 0.074 ounce, 2.1 gram 1.0(25.4) MIN. 0.052(1.3) 0.048(1.2) DIA. Dimensions in inches and (millimeters) Maximum Ratings And Electrical Characteristics (Ratings at 25℃ ambient temperature unless otherwise specified, Single phase, half wave 60Hz, resistive or inductive load. For capacitive load, derate by 20%) Symbols HER 601 HER 602 HER 603 HER 604 HER 605 HER 606 HER 607 HER 608 Units Maximum recurrent peak reverse voltage VRRM 50 100 200 300 400 600 800 1000 Volts Maximum RMS voltage VRMS 35 70 140 210 280 420 560 700 Volts Maximum DC blocking voltage VDC 50 100 200 300 400 600 800 1000 Volts Maximum average forward rectified current 0.375"(9.5mm) lead length @ at TA=55℃ I(AV) 6.0 Amps Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC method) IFSM 200.0 Amps Maximum instantaneous forward voltage at 2.0A VF 1.0 1.3 Maximum DC reverse current at rated DC blocking voltage TA=25℃ Maximum DC reverse current at rated DC blocking voltage TA=100℃ Volts 10.0 μA IR 200 Maximum reverse recovery time (Note 1) Trr 50 Typical junction capacitance (Note 2) CJ 100 Operating junction and storage temperature range 1.7 TJ TSTG Notes: (1) Test conditions: IF=0.5A, IR=1.0A, Irr=0.25A. (2) Measured at 1MHz and applied reverse voltage of 4.0 Volts. -65 to +125 -65 to +150 75 ns 65 pF ℃ RATINGS AND CHARACTERISTIC CURVES HER601 THRU HER608 50W NON INDUCTIVE (+) 10W NON INDUCTIVE D.U.T. ) 1W NON INDUCTIVE 0 PULSE GENERATOR (NOTE2) 25Vdc (APPROX) ( Trr +0.5A -0.25A OSCILLOSCOPE (NOTE1) -1.0A NOTES : 1.Rise Time=7ns max. input impedance=1 megohm 22pF 2.Rise Time=10ns max. source impedance = 50 ohms AVERAGE FORWARD CURRENT(A) FIG.2-TYPICAL FORWARD CURRENT DERATING CURVE FIG.1-TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC 1cm 6.0 5.0 4.0 3.0 2.0 SINGLE PHASE HALF WAVE 60Hz RESISTIVE OR INDUCTIVE LOAD 0.375"(9.5mm) LEAD LENGTH 1.0 0 0 SET TIME BASE FOR 20/30 ns/cm 25 50 75 100 125 150 175 AMBIENT TEMPERATURE ( ℃) FIG.4-TYPICAL REVERSE CHARACTERISTICS 1000 INSTANTANEOUS REVERSE CURRENT (mA) 100 8 60 HE R6 07 1 -H ER HE R6 05 H R6 01 H ER ER 60 6 60 4 10 HE INSTANTANEOUS FORWARD CURRENT(AMPERES) FIG.3-TYPICAL FORWARD CHARACTERISTICS 0.1 TA=25℃ PULSE WIDTH=300mS 0.2 0.4 0.6 0.8 1.0 1.2 1.4 10 TA=25℃ 1.0 0.1 1% DUTY CYCLE 0.01 0 TA=100℃ 100 1.6 0 20 1.8 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE (%) INSTANTANEOUS FORWARD VOLTAGE (VOLTS) FIG.5-MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT FIG6-TYPICAL JUNCTION CAPACITANCE 350 175 TA=25℃ 8.3m SINGLE HALF SINE WAVE (JEDEC Method) 250 JUNCTION CAPACITANCE(pF) PEAK FORWARD SURGE CURRENT(AMPERES) 300 200 150 100 50 0 1 5 10 NUMBER OF CYCLES AT 60Hz 50 100 150 125 HER601-HER606 100 75 TJ=25℃ 50 HER607-HER608 25 0 0.1 0.5 1 2 5 10 20 REVERSE VOLTAGE. (V) 50 100 200 1000