TI1 ISO7821LLSDWWR High-performance, 8000-vpk reinforced isolated dual-lvds buffer Datasheet

Sample &
Buy
Product
Folder
Support &
Community
Tools &
Software
Technical
Documents
ISO7821LLS
SLLSET5A – MARCH 2016 – REVISED SEPTEMBER 2016
ISO7821LLS High-Performance, 8000-VPK Reinforced Isolated Dual-LVDS Buffer
1 Features
2 Applications
•
•
•
•
•
•
•
•
•
•
•
1
•
•
•
•
•
•
•
•
•
Complies with TIA/EIA-644-A LVDS Standard
Signaling Rate: 50 Mbps to 150 Mbps
Optimized for DC-Balanced Data
Wide Supply Range: 3 V to 5.5 V
Wide Temperature Range: –55°C to 125°C
Low-Power Consumption, Typical 10.3 mA per
Channel at 150 Mbps
Low Propagation Delay: 17 ns Typical
Industry leading CMTI(Min): ±100 kV/μs
Robust Electromagnetic Compatibility (EMC)
System-Level ESD, EFT, and Surge Immunity
Low Emissions
Isolation Barrier Life: > 40 Years
SOIC-16 Wide Body (DW) and Extra-Wide Body
(DWW) Package Options
Isolation Surge Withstand Voltage 12800 VPK
Safety-Related Certifications:
– 8000-VPK Reinforced Isolation per DIN V VDE
V 0884–10 (VDE V 0884–10): 2006–12
– 5700-VRMS Isolation for 1 minute per UL 1577
– CSA Component Acceptance Notice 5A, IEC
60950–1 and IEC 60601–1 End Equipment
Standards
– TUV Certification per EN 61010-1 and EN
60950-1
– CQC Certification per GB4943.1–2011
– All Certifications are Planned
Motor Control
Test and Measurement
Industrial Automation
Medical Equipment
Communication Systems
3 Description
The ISO7821LLS device is a high-performance,
isolated dual-LVDS buffer with 8000-VPK isolation
voltage. This device provides high electromagnetic
immunity and low emissions at low-power
consumption, while isolating the LVDS bus signal.
Each isolation channel has an LVDS receive and
transmit buffer. Timing performance for the
ISO7821LLS device is optimized for use with
communication systems that use DC-balanced data
streams which is achieved through an internal
distortion correction scheme.
The ISO7821LLS device has one forward and one
reverse-direction channel.
Through innovative chip design and layout
techniques, the electromagnetic compatibility of the
ISO7821LLS device has been significantly enhanced
to ease system-level ESD, EFT, surge, and
emissions compliance.
The ISO7821LLS device is available in a 16-pin SOIC
wide-body (DW) and extra-wide body (DWW)
packages.
Device Information(1)
PART NUMBER
ISO7821LLS
PACKAGE
BODY SIZE (NOM)
DW (16)
10.30 mm × 7.50 mm
DWW (16)
10.30 mm × 14.00 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
Simplified Schematic
VCCI
Isolation
Capacitor
VCCO
INx+
OUTx+
LVDS RX
LVDS TX
INx±
OUTx±
ENx
GNDI
GNDO
Copyright © 2016, Texas Instruments Incorporated
VCCI and GNDI are supply and ground connections respectively for the input channels.
VCCO and GNDO are supply and ground connections respectively for the output channels.
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
ISO7821LLS
SLLSET5A – MARCH 2016 – REVISED SEPTEMBER 2016
www.ti.com
Table of Contents
1
2
3
4
5
6
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
2
3
4
6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8
6.9
6.10
6.11
Absolute Maximum Ratings ..................................... 4
ESD Ratings.............................................................. 4
Recommended Operating Conditions....................... 4
Thermal Information .................................................. 5
Power Ratings........................................................... 5
Insulation Specifications............................................ 6
Safety-Related Certifications..................................... 7
Safety Limiting Values .............................................. 7
DC Electrical Characteristics .................................... 8
DC Supply Current Characteristics ......................... 9
Timing Requirements for Distortion Correction
Scheme ...................................................................... 9
6.12 Switching Characteristics ...................................... 10
6.13 Insulation Characteristics Curves ......................... 11
6.14 Typical Characteristics .......................................... 12
7
8
Detailed Description ............................................ 17
8.1
8.2
8.3
8.4
9
Overview .................................................................
Functional Block Diagram .......................................
Feature Description.................................................
Device Functional Modes........................................
17
17
18
19
Application and Implementation ........................ 20
9.1 Application Information............................................ 20
9.2 Typical Application .................................................. 20
10 Power Supply Recommendations ..................... 23
11 Layout................................................................... 24
11.1 Layout Guidelines ................................................. 24
11.2 Layout Example .................................................... 24
12 Device and Documentation Support ................. 25
12.1
12.2
12.3
12.4
12.5
12.6
Documentation Support ........................................
Receiving Notification of Documentation Updates
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
25
25
25
25
25
25
13 Mechanical, Packaging, and Orderable
Information ........................................................... 25
Parameter Measurement Information ................ 14
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Original (March 2016) to Revision A
•
2
Page
Changed the device status from Product Preview to Production Data and released full version of the data sheet .............. 1
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: ISO7821LLS
ISO7821LLS
www.ti.com
SLLSET5A – MARCH 2016 – REVISED SEPTEMBER 2016
5 Pin Configuration and Functions
DW and DWW Packages
16-Pin SOIC
Top View
1
16 VCC2
GND1
2
15 GND2
INA+
3
14 OUTA+
INA±
4
OUTB± 5
ISOLATION
VCC1
13 OUTA±
OUTB+ 6
EN1
7
GND1
8
12
INB±
11
INB+
10
EN2
9 GND2
Pin Functions
PIN
NAME
NO.
I/O
DESCRIPTION
EN1
7
I
Output enable 1. Output pins on side 1 are enabled when EN1 is high or open and in high
impedance state when EN1 is low.
EN2
10
I
Output enable 2. Output pins on side 2 are enabled when EN2 is high or open and in high
impedance state when EN2 is low.
GND1
GND2
2
8
9
15
—
Ground connection for VCC1
—
Ground connection for VCC2
INA+
3
I
Positive differential input, channel A
INA–
4
I
Negative differential input, channel A
INB+
11
I
Positive differential input, channel B
INB–
12
I
Negative differential input, channel B
OUTA+
14
O
Positive differential output, channel A
OUTA–
13
O
Negative differential output, channel A
OUTB+
6
O
Positive differential output, channel B
OUTB–
5
O
Negative differential output, channel B
VCC1
1
—
Power supply, side 1, VCC1
VCC2
16
—
Power supply, side 2, VCC2
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: ISO7821LLS
3
ISO7821LLS
SLLSET5A – MARCH 2016 – REVISED SEPTEMBER 2016
www.ti.com
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted) (1)
MIN
MAX
UNIT
VCCx
Supply voltage (2)
VCC1, VCC2
–0.5
6
V
V
Voltage on input, output, and
enable pins
OUTx, INx, ENx
–0.5
VCCx + 0.5 (3)
V
IO
Maximum current through OUTx pins
–20
20
mA
TJ
Junction temperature
–55
150
°C
Tstg
Storage temperature
–65
150
°C
(1)
(2)
(3)
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltage values except differential I/O bus voltages are with respect to the local ground pin (GND1 or GND2) and are peak voltage
values.
Maximum voltage must not exceed 6 V.
6.2 ESD Ratings
VALUE
V(ESD)
(1)
(2)
Electrostatic
discharge
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001
(1)
UNIT
±4500
Charged-device model (CDM), per JEDEC specification JESD22-C101 (2)
V
±1500
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
VCC1, VCC2
Supply voltage
|VID|
Magnitude of RX input
differential voltage
Driven with voltage sources on RX pins
VIC
RX input commonmode voltage
VCC1, VCC2 ≥ 3 V
RL
TX far-end differential termination
DR
Signaling rate
TA
Ambient temperature
4
MIN
NOM
MAX
3
3.3
5.5
V
100
600
mV
0.5 |VID|
2.4 – 0.5 |VID|
100
50
–55
Submit Documentation Feedback
25
UNIT
V
Ω
150
Mbps
125
°C
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: ISO7821LLS
ISO7821LLS
www.ti.com
SLLSET5A – MARCH 2016 – REVISED SEPTEMBER 2016
6.4 Thermal Information
ISO7821LLS
THERMAL METRIC (1)
DW (SOIC)
DWW (SOIC)
16 PINS
16 PINS
UNIT
82
84.6
°C/W
RθJA
Junction-to-ambient thermal resistance
RθJC(top)
Junction-to-case(top) thermal resistance
44.6
46.4
°C/W
RθJB
Junction-to-board thermal resistance
46.6
55.3
°C/W
ψJT
Junction-to-top characterization parameter
17.8
18.7
°C/W
ψJB
Junction-to-board characterization parameter
46.1
54.5
°C/W
RθJC(bottom)
Junction-to-case(bottom) thermal resistance
—
—
°C/W
(1)
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
6.5 Power Ratings
VCC1 = VCC2 = 5.5 V, TJ = 150°C, CL = 5 pF, RL = 100-Ω differential, input a 75-MHz 50% duty-cycle square wave,
EN1 = EN2 = 5.5 V
PARAMETER
TEST CONDITIONS
MAX
UNIT
180
mW
Maximum power dissipation (side 1)
90
mW
Maximum power dissipation (side 2)
90
mW
PD
Maximum power dissipation (both sides)
PD1
PD2
MAX
TYP
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: ISO7821LLS
5
ISO7821LLS
SLLSET5A – MARCH 2016 – REVISED SEPTEMBER 2016
www.ti.com
6.6 Insulation Specifications
over operating free-air temperature range (unless otherwise noted)
PARAMETER
SPECIFICATION
TEST CONDITIONS
DW
DWW
UNIT
GENERAL
External clearance (1)
Shortest terminal-to-terminal distance through air
>8
>14.5
mm
CPG
External creepage (1)
Shortest terminal-to-terminal distance across the
package surface
>8
>14.5
mm
DTI
Distance through the insulation
Minimum internal gap (internal clearance)
>21
>21
μm
CTI
Tracking resistance (comparative
tracking index)
DIN EN 60112 (VDE 0303–11); IEC 60112; UL 746A
>600
>600
V
Material group
According to IEC 60664-1
CLR
Overvoltage category per IEC 60664-1
DIN V VDE V 0884–10 (VDE V 0884–10):2006–12
VIORM
Maximum repetitive peak isolation
voltage
VIOWM Maximum isolation working voltage
I
I
Rated mains voltage ≤ 600 VRMS
I–IV
I–IV
Rated mains voltage ≤ 1000 VRMS
I–III
I–IV
AC voltage (bipolar)
2121
2828
VPK
AC voltage (sine wave); time dependent dielectric
breakdown (TDDB) test; see Figure 1 and Figure 2
1500
2000
VRMS
DC voltage
2121
2828
VDC
8000
8000
VPK
8000
8000
VPK
Method a: After I/O safety test subgroup 2/3,
Vini = VIOTM, tini = 60 s;
Vpd(m) = 1.2 × VIORM = 2545 VPK (DW) and
3394 VPK (DWW), tm = 10 s
≤5
≤5
Method a: After environmental tests subgroup 1,
Vini = VIOTM, tini = 60 s;
Vpd(m) = 1.6 × VIORM = 3394 VPK (DW) and
4525 VPK (DWW), tm = 10 s
≤5
≤5
Method b1: At routine test (100% production) and
preconditioning (type test)
Vini = VIORM, tini = 1 s;
Vpd(m) = 1.875 × VIORM= 3977 VPK (DW) and
5303 VPK (DWW), tm = 1 s
≤5
≤5
(2)
VIOTM
Maximum transient isolation voltage
VTEST = VIOTM, t = 60 s (qualification)
t = 1 s (100% production)
VIOSM
Maximum surge isolation voltage (3)
Test method per IEC 60065, 1.2/50 µs waveform,
VTEST = 1.6 × VIOSM = 12800 VPK (qualification)
qpd
Apparent charge
(4)
Barrier capacitance, input to output (5)
CIO
Isolation resistance, input to output (5)
RIO
VIO = 0.4 × sin (2πft), f = 1 MHz
~0.7
~0.7
VIO = 500 V, TA = 25°C
>1012
>1012
VIO = 500 V, 100°C ≤ TA ≤ 125°C
>1011
>1011
9
>109
VIO = 500 V at TS = 150°C
>10
Pollution degree
2
2
Climatic category
55/125/21
55/125/21
5700
5700
pC
pF
Ω
UL 1577
VISO
(1)
(2)
(3)
(4)
(5)
6
Withstanding isolation voltage
VTEST = VISO = 5700 VRMS, t = 60 s (qualification);
VTEST = 1.2 × VISO = 6840 VRMS,
t = 1 s (100% production)
VRMS
Creepage and clearance requirements should be applied according to the specific equipment isolation standards of an application. Care
should be taken to maintain the creepage and clearance distance of a board design to ensure that the mounting pads of the isolator on
the printed-circuit board do not reduce this distance. Creepage and clearance on a printed-circuit board become equal in certain cases.
Techniques such as inserting grooves and/or ribs on a printed circuit board are used to help increase these specifications.
This coupler is suitable for safe electrical insulation only within the safety ratings. Compliance with the safety ratings shall be ensured by
means of suitable protective circuits.
Testing is carried out in air or oil to determine the intrinsic surge immunity of the isolation barrier.
Apparent charge is electrical discharge caused by a partial discharge (pd).
All pins on each side of the barrier tied together creating a two-terminal device.
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: ISO7821LLS
ISO7821LLS
www.ti.com
SLLSET5A – MARCH 2016 – REVISED SEPTEMBER 2016
6.7 Safety-Related Certifications
VDE
CSA
Plan to certify according to
DIN V VDE V 0884-10
(VDE V 0884-10):2006-12
and DIN EN 60950-1 (VDE
0805 Teil 1):2011-01
UL
Plan to certify under CSA
Component Acceptance
Notice 5A, IEC 60950-1 and
IEC 60601-1
Plan to certify according
to UL 1577 Component
Recognition Program
CQC
TUV
Plan to certify according to
GB 4943.1-2011
Reinforced insulation per CSA
60950-1-07+A1+A2 and IEC
60950-1 2nd Ed., 800 VRMS
Reinforced insulation
(DW package) and 1450 VRMS
Maximum transient
isolation voltage, 8000 VPK; (DWW package) max working
voltage (pollution degree 2,
Maximum repetitive peak
Single protection,
isolation voltage, 2121 VPK material group I);
5700 VRMS
(DW), 2828 VPK (DWW);
2 MOPP (Means of Patient
Maximum surge isolation
Protection) per CSA 60601voltage, 8000 VPK
1:14 and IEC 60601-1 Ed. 3.1,
250 VRMS (354 VPK) max
working voltage (DW package)
Reinforced Insulation,
Altitude ≤ 5000 m, Tropical
Climate, 250 VRMS
maximum working voltage
Certification planned
Certification planned
Certification planned
Certification planned
Plan to certify according to
EN 61010-1:2010 (3rd Ed) and
EN 60950-1:2006/A11:2009/A1:2010/
A12:2011/A2:2013
5700 VRMS Reinforced insulation per
EN 61010-1:2010 (3rd Ed) up to
working voltage of 600 VRMS (DW
package) and 1000 VRMS (DWW
package)
5700 VRMS Reinforced insulation per
EN 60950-1:2006/A11:2009/A1:2010/
A12:2011/A2:2013 up to working
voltage of 800 VRMS (DW package) and
1450 VRMS (DWW package)
Certification planned
6.8 Safety Limiting Values
Safety limiting intends to minimize potential damage to the isolation barrier upon failure of input or output circuitry. A failure of
the I/O can allow low resistance to ground or the supply and, without current limiting, dissipate sufficient power to overheat
the die and damage the isolation barrier potentially leading to secondary system failures.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
DW PACKAGE
IS
Safety input, output, or supply
current
PS
Safety input, output, or total power
TS
Maximum safety temperature
RθJA = 82°C/W, VI = 5.5 V, TJ = 150°C, TA = 25°C,
see Figure 3
277
RθJA = 82°C/W, VI = 3.6 V, TJ = 150°C, TA = 25°C,
see Figure 3
423
mA
RθJA = 82°C/W, TJ = 150°C, TA = 25°C,
see Figure 5
1524
mW
150
°C
DWW PACKAGE
IS
Safety input, output, or supply
current
PS
Safety input, output, or total power
TS
Maximum safety temperature
RθJA = 84.6°C/W, VI = 5.5 V, TJ = 150°C, TA = 25°C,
see Figure 4
269
RθJA = 84.6°C/W, VI = 3.6 V, TJ = 150°C, TA = 25°C,
see Figure 4
410
RθJA = 84.6°C/W, TJ = 150°C, TA = 25°C,
see Figure 6
mA
1478
mW
150
°C
The maximum safety temperature is the maximum junction temperature specified for the device. The power
dissipation and junction-to-air thermal impedance of the device installed in the application hardware determines
the junction temperature. The assumed junction-to-air thermal resistance in the Thermal Information is that of a
device installed on a High-K test board for leaded surface-mount packages. The power is the recommended
maximum input voltage times the current. The junction temperature is then the ambient temperature plus the
power times the junction-to-air thermal resistance.
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: ISO7821LLS
7
ISO7821LLS
SLLSET5A – MARCH 2016 – REVISED SEPTEMBER 2016
www.ti.com
6.9 DC Electrical Characteristics
(over recommended operating conditions unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
13
40
µA
2.25
V
GENERAL
IIN(EN)
Leakage Current on ENx
pins
VCC+(UVLO)
Positive-going undervoltagelockout (UVLO) threshold
VCC–(UVLO)
Negative-going UVLO
threshold
VHYS(UVLO)
UVLO threshold hysteresis
VEN(ON)
EN pin turn-on threshold
VEN(OFF)
EN pin turn-off threshold
VEN(HYS)
EN pin threshold hysteresis
Internal pullup on ENx pins
1.7
V
0.2
V
0.7 VCCx
0.3 VCCx
V
V
0.1 VCCx
V
(1)
Common-mode transient
immunity
VI = VCCI or 0 V;
VCM = 1000 V, see Figure 22
100
120
|VOD|
TX DC output differential
voltage
RL = 100 Ω, see Figure 23
250
350
450
mV
∆VOD
Change in TX DC output
differential between logic 1
and 0 states
RL = 100 Ω, see Figure 23
–10
0
10
mV
VOC
TX DC output commonmode voltage
RL = 100 Ω, see Figure 23
1.125
1.2
1.375
∆VOC
TX DC common-mode
voltage difference
RL = 100 Ω, see Figure 23
–25
0
25
IOS
TX output short circuit
current through OUTx
IOZ
TX output current when in
high impedance
CMTI
kV/μs
LVDS TX
TX output pad capacitance
on OUTx at 1 MHz
COUT
OUTx = 0
10
OUTxP = OUTxM
10
ENx = 0, OUTx from 0 to VCCx
–5
5
DW package: ENx = 0, DC offset = VCC / 2,
Swing = 200 mV, Frequency (f) = 1 MHz
10
DWW package: ENx = 0,
DC offset = VCC / 2, Swing = 200 mV,
Frequency (f) = 1 MHz
10
V
mV
mA
µA
pF
LVDS RX
VIC
RX input common mode
voltage
VCCx ≥ 3 V
VIT1
Positive going RX input
differential threshold
Across VIC
VIT2
Negative going RX input
differential threshold
Across VIC
IINx
Input current on INx
From 0 to VCC (each input independently)
IINxP – IINxM
Input current balance
From 0 to VCC
CIN
DW package: DC offset = 1.2 V,
RX input pad capacitance on Swing = 200 mV, f = 1 MHz
INx at 1 MHz
DWW package: DC offset = 1.2 V,
Swing = 200 mV, f = 1 MHz
(1)
8
0.5 |VID|
1.2
2.4 – 0.5 |VID|
50
–50
V
mV
mV
10
–6
20
µA
6
µA
6.6
pF
7.5
VCCI = Input-side VCCx; VCCO = Output-side VCCx.
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: ISO7821LLS
ISO7821LLS
www.ti.com
SLLSET5A – MARCH 2016 – REVISED SEPTEMBER 2016
6.10 DC Supply Current Characteristics
(over recommended operating conditions unless otherwise noted)
PARAMETER
TEST CONDITIONS
3 V < VCC1,
VCC2 < 3.6 V
ICC1
ICC2
Supply current
side 1 and
side 2
MIN
TYP MAX
EN1 = EN2 = 0, OUTx floating, VID ≥ 50 mV
2.3
3.6
EN1 = EN2 = 0, OUTx floating, VID ≤ –50 mV
3.5
5.6
EN1 = EN2 = 1, RL = 100-Ω differential, VID ≥ 50 mV
6.2
9.9
EN1 = EN2 = 1, RL = 100-Ω differential, VID ≤ –50 mV
7.5
12
EN1 = EN2 = 1, RL = 100-Ω differential, data communication at
50 Mbps
7.6
12.1
EN1 = EN2 = 1, RL = 100-Ω differential, data communication at
125 Mbps
8.5
13.6
EN1 = EN2 = 1, RL = 100-Ω differential, data communication at
150 Mbps
8.9
14.2
EN1 = EN2 = 0, OUTx floating, VID ≥ 50 mV
2.3
3.6
EN1 = EN2 = 0, OUTx floating, VID ≤ –50 mV
3.6
5.7
EN1 = EN2 = 1, RL = 100-Ω differential, VID ≥ 50 mV
6.6
10.5
7.9
12.6
8.3
13.2
EN1 = EN2 = 1, RL = 100-Ω differential, data communication at
125 Mbps
9.7
15.5
EN1 = EN2 = 1, RL = 100-Ω differential, data communication at
150 Mbps
10.3
16.4
EN1 = EN2 = 1, RL = 100-Ω differential, VID ≤ –50 mV
4.5 V < VCC1,
EN1 = EN2 = 1, RL = 100-Ω differential, data communication at
VCC2 < 5.5 V
50 Mbps
UNIT
mA
6.11 Timing Requirements for Distortion Correction Scheme
Valid data = 8b10b like data with DC balance and bounded disparity. See Figure 25.
MIN
tCALIB
Time to complete internal calibration, after exiting idle state. LVDS TX
output is held high during this time. During this time valid data must be
presented at the receiver.
tIDLE
The minimum duration of any idle state that must be maintained between
valid data transmissions.
tIDLE_OUT
After a channel enters idle state, the internal calibration loses lock after this
time, and the LVDS outputs are gated high.
250
NOM
MAX
UNIT
750
µs
10
200
µs
600
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: ISO7821LLS
ns
9
ISO7821LLS
SLLSET5A – MARCH 2016 – REVISED SEPTEMBER 2016
www.ti.com
6.12 Switching Characteristics
(over recommended operating conditions unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
17
25
ns
LVDS CHANNEL
tPLH
tPHL
Propagation delay time
tsk(o)
Channel-to-channel output skew time
Opposite directional channels, same
voltage and temperature
4.5
ns
tsk(pp)
Part-part skew
Same directional channels, same
voltage and temperature
4.5
ns
tCMset
Common-mode setting time after
EN = 0 to EN = 1 transition
Common-mode capacitive
load = 100 pF to 0.5 nF
20
µs
Total eye closure
Default output delay time from input
power loss
tfs
DC balanced data with maximum run
length of 6 at 125 Mbps,
RX VID = 350 mVPP, 1 ns trf 10%-90%,
–40 < TA < 125°C, 3 V < VCC1,
VCC2 < 5 V
30%
DC balanced data with maximum run
length of 6 at 150 Mbps,
RX VID = 350 mVPP, 1 ns trf 10%-90%,
–40 < TA < 125°C, 3 V < VCC1,
VCC2 < 5 V
40%
Measured from the time VCC goes
below 1.7 V, see Figure 21
0.2
9
µs
780
1380
ps
0
150
mVPP
LVDS TX AND RX
trf
TX differential rise and fall times
(20% to 80%)
∆VOC(pp)
TX common-mode voltage peak-topeak at 100 Mbps
tPLZ, tPHZ TX disable time—valid output to HiZ
See Figure 19
300
See Figure 20
10
20
ns
tPZH
TX enable time—HiZ to valid high
output (1)
See Figure 20
10
20
ns
|VID|
Magnitude of RX input differential
voltage for valid operation
Driven with voltage sources on RX pins,
see figures in the Parameter
Measurement Information section
600
mV
trf(RX)
Allowed RX input differential rise and
fall times (20% to 80%)
See Figure 24
0.3 × UI (2)
ns
(1)
(2)
10
100
1
The tPZL parameter is not defined because of the distortion-correction scheme. See the Distortion-Correction Scheme section for more
information.
UI is the unit interval.
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: ISO7821LLS
ISO7821LLS
www.ti.com
SLLSET5A – MARCH 2016 – REVISED SEPTEMBER 2016
6.13 Insulation Characteristics Curves
1.E+11
87.5%
1.E+9
1.E+9
1.E+8
1.E+8
1.E+7
1.E+6
1.E+5
Safety Margin Zone: 2400 VRMS, 63 Years
Operating Zone: 2000 VRMS, 34 Years
TDDB Line (<1 PPM Fail Rate)
1.E+10
Time to Fail (s)
Time to Fail (s)
1.E+10
1.E+11
Safety Margin Zone: 1800 VRMS, 254 Years
Operating Zone: 1500 VRMS, 135 Years
TDDB Line (<1 PPM Fail Rate)
87.5%
1.E+7
1.E+6
1.E+5
1.E+4
1.E+4
1.E+3
1.E+3
20%
1.E+2
1.E+2
1.E+1
500
1.E+1
400
20%
1500 2500 3500 4500 5500 6500 7500 8500 9500
Stress Voltage (VRMS)
TA upto 150°C
Operating lifetime = 135 years
Stress-voltage frequency = 60 Hz
Isolation working voltage = 1500 VRMS
1400 2400 3400 4400 5400 6400 7400 8400 9400
Stress Voltage (VRMS)
TA upto 150°C
Figure 1. Reinforced Isolation Capacitor Lifetime Projection
for Devices in DW Package
Operating lifetime = 34 years
Stress-voltage frequency = 60 Hz
Isolation working voltage = 2000 VRMS
Figure 2. Reinforced Isolation Capacitor Lifetime Projection
for Devices in DWW Package
500
500
VCCx = 3.6 V
VCCx = 5.5 V
Safety Limiting Current (mA)
Safety Limiting Current (mA)
VCCx = 3.6 V
VCCx = 5.5 V
400
300
200
100
0
400
300
200
100
0
0
50
100
150
Ambient Temperature (qC)
200
0
50
D006
100
150
Ambient Temperature (qC)
D008
Figure 3. Thermal Derating Curve for Limiting Current for
DW Package
Figure 4. Thermal Derating Curve for Limiting Current for
DWW Package
1800
1600
Power
Power
1600
1400
Safety Limiting Power (mW)
Safety Limiting Power (mW)
200
1400
1200
1000
800
600
400
1200
1000
800
600
400
200
200
0
0
0
50
100
150
Ambient Temperature (qC)
200
0
D007
Figure 5. Thermal Derating Curve for Limiting Power for DW
Package
50
100
150
Ambient Temperature (qC)
200
D009
D010
D001
Figure 6. Thermal Derating Curve for Limiting Power for
DWW Package
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: ISO7821LLS
11
ISO7821LLS
SLLSET5A – MARCH 2016 – REVISED SEPTEMBER 2016
www.ti.com
10
10
8
8
Supply Current (mA)
Supply Current (mA)
6.14 Typical Characteristics
6
4
ICC1 at 3.3 V
ICC2 at 3.3 V
ICC1 at 5 V
ICC2 at 5 V
2
0
50
75
100
Data Rate (Mbps)
TA = 25°C
125
6
4
ICC1 at 3.3 V
ICC2 at 3.3 V
ICC1 at 5 V
ICC2 at 5 V
2
0
50
150
75
100
Data Rate (Mbps)
D001
CH-A toggle
TA = 25°C
Figure 7. Supply Current vs Data Rate (CH-A)
125
150
D002
CH-B toggle
Figure 8. Supply Current vs Data Rate (CH-B)
10
14
12
Supply Current (mA)
Supply Current (mA)
8
10
8
6
4
6
4
ICC1 at 3.3 V
ICC2 at 3.3 V
ICC1 at 5 V
ICC2 at 5 V
2
2
ICC1, ICC2 at 50 Mbps
ICC1, ICC2 at 150 Mbps
0
-55
0
3
3.5
4
4.5
5
VCCx Output Supply Voltage (V)
5.5
-35
-15
5
D003
TA = 25°C
Data rate = 150 Mbps
Figure 9. Supply Current vs VCCx Output Supply Voltage
25
45
65
Temperature (qC)
85
105
125
D004
CH-A toggle
Figure 10. Supply Current vs Temperature (CH-A)
10
16
Propagation Delay Time (ns)
15
Supply Current (mA)
8
6
4
ICC1 at 3.3 V
ICC2 at 3.3 V
ICC1 at 5 V
ICC2 at 5 V
2
0
-55
-35
-15
Data rate = 150 Mbps
5
25
45
65
Temperature (qC)
85
105
13
12
11
10
tPLH at 3.3 V
tPHL at 3.3 V
tPLH at 5 V
tPHL at 5 V
9
125
8
-55
-35
D005
-15
5
25
45
65
Temperature (qC)
85
105
125
D010
CH-B toggle
Figure 11. Supply Current vs Temperature (CH-B)
12
14
Figure 12. Propagation Delay Time vs Temperature
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: ISO7821LLS
ISO7821LLS
www.ti.com
SLLSET5A – MARCH 2016 – REVISED SEPTEMBER 2016
Typical Characteristics (continued)
17
3
tPLH
tPHL
VOUT+
VOC
VOUT
15
Output Voltage (V)
Propagation Delay Time (ns)
16
14
13
12
11
2
1
10
9
8
0
3
3.5
4
4.5
5
VCCx Output Supply Voltage (V)
5.5
3
3.5
D011
TA = 25°C
4
4.5
5
VCCx Output Supply Voltage (V)
5.5
D012
TA = 25°C
Figure 13. Propagation Delay Time vs VCCx Output Supply
Voltage
Figure 14. Output Voltage vs VCCx Output Supply Voltage
15
15
Input to LVDS RX
Input to LVDS RX
Output from
LVDS TX
Output from
LVDS TX
D023
Figure 15. Distortion Correction Scheme Calibration Time
(tCALIB)
15
D023
Figure 16. Transition From Valid Data to Idle (tIDLE_OUT)
15
VI
VI
VOD
VOD
D023
Figure 17. Disable to Enable Time (tPZH)
D023
Figure 18. Disable Time (tPLZ, tPHZ)
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: ISO7821LLS
13
ISO7821LLS
SLLSET5A – MARCH 2016 – REVISED SEPTEMBER 2016
www.ti.com
7 Parameter Measurement Information
VCCI
Isolation Capacitor
INx+
100
Signal
V
Generator ID
CP
VCCO
LVDS RX
INx±
VID(H)
OUTx+
50%
VID
VID(L)
RL
LVDS TX
OUTx±
50%
VOD
tPLH
CP
tPHL
VOD
GNDI
GNDO
VOD(H)
80%
50%
50%
20%
VOD(L)
tf
tr
A.
The input pulse is supplied by a generator having the following characteristics: PRR ≤ 50 kHz, 50% duty cycle, tr ≤ 3
ns, tf ≤ 3 ns, ZO = 50 Ω.
B.
CP = 5 pF and includes instrumentation and fixture capacitance within ±20%.
Figure 19. Switching Characteristics Test Circuit and Voltage Waveforms
VCCI
Isolation Capacitor
VCCO
INx+
LVDS RX
VID 100
VID ” ±50 mV
INx±
OUTx+
LVDS TX
RL
CL VOD
VCCO / 2
OUTx±
0V
tPLZ
EN
GNDI
VCCO
VI
0V
GNDO
50%
VOD(L)
VOD
Signal
Generator
VI
50
VCCI
Isolation Capacitor
VCCO
INx+
LVDS RX
VID 100
VID • 50 mV
INx±
OUTx+
LVDS TX
RL
VCCO
CL VOD
0V
tPZH
EN
GNDI
VOD(H)
GNDO
VOD
Signal
Generator
VCCO / 2
VCCO / 2
VI
OUTx±
50%
50%
tPHZ
VI
0V
50
A.
The input pulse is supplied by a generator having the following characteristics: PRR ≤ 10 kHz, 50% duty cycle,
tr ≤ 3 ns, tf ≤ 3 ns, ZO = 50 Ω.
B.
CL = 5 pF and includes instrumentation and fixture capacitance within ±20%.
Figure 20. Enable and Disable Propagation Delay Time Test Circuit and Waveform
14
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: ISO7821LLS
ISO7821LLS
www.ti.com
SLLSET5A – MARCH 2016 – REVISED SEPTEMBER 2016
Parameter Measurement Information (continued)
VI
Isolation Capacitor
INx+
LVDS RX
VID 100
VID ” ±50 mV
VCCI
VCCO
VCCI
INx±
1.7 V
VI
OUTx+
0V
LVDS TX
CL VOD
RL
tfs
OUTx±
VOD(H)
50%
VOD
VOD(L)
GNDI
A.
GNDO
CL = 5 pF and includes instrumentation and fixture capacitance within ±20%.
Figure 21. Default Output Delay Time Test Circuit and Voltage Waveforms
VCCI
Isolation Capacitor
VCCO
INx+
S1
VID
LVDS RX
100
S2
INx±
GNDI
A.
+
VCM
OUTx+
LVDS TX
CL VOD
RL
OUTx±
±
GNDO
CL = 5 pF and includes instrumentation and fixture capacitance within ±20%.
Figure 22. Common-Mode Transient Immunity Test Circuit
VCCI
100
LVDS RX
INx±
GNDI
Isolation Capacitor
INx+
VCCO
RL / 2
OUTx+
LVDS TX
V
V
OUTx±
RL / 2
VOC
VOD
GNDO
= Measured Parameter
Figure 23. Driver Test Circuit
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: ISO7821LLS
15
ISO7821LLS
SLLSET5A – MARCH 2016 – REVISED SEPTEMBER 2016
www.ti.com
Parameter Measurement Information (continued)
VCCI
Isolation Capacitor
VCCO
INx+
LVDS RX
VID
INx±
VIN+
VIN±
GNDI
OUTx+
LVDS TX
VOD
OUTx±
VOUT+
VOUT±
GNDO
1.375 V
VIN+
1.025 V
VIN±
U
I
VID
VID(H), 0.35 V
0V
VID(L), ±0.35 V
tPHL
tPLH
VOD(H)
VOD
80%
50%
20%
tf
VOD(L)
tr
Figure 24. Voltage Definitions and Waveforms
16
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: ISO7821LLS
ISO7821LLS
www.ti.com
SLLSET5A – MARCH 2016 – REVISED SEPTEMBER 2016
8 Detailed Description
8.1 Overview
The ISO7821LLS device is an isolated LVDS buffer. The differential signal received on the LVDS input pins is
first converted to CMOS logic levels. It is then transmitted across a silicon dioxide based capacitive isolation
barrier using an On-Off Keying (OOK) modulation scheme. A high frequency carrier transmitted across the
barrier represents one logic state and an absence of a carrier represents the other logic state. On the other side
of the barrier a demodulator converts the OOK signal back to logic levels, which is then converted to LVDS
outputs by a differential driver. This device incorporates advanced circuit techniques to maximize CMTI
performance and minimize radiated emissions.
The ISO7821LLS device implements an eye-diagram improvement scheme to correct for signal distortions that
are introduced in the LVDS receiver as well as the isolation channel. This enables the device to guarantee an
eye closure of less than 30% at 125 Mbps, and less than 40% at 150 Mbps. The distortion correction scheme is
optimized for operation with DC balanced data (for example 8b10b or equivalent) with a maximum run length of
6. The minimum data-rate of operation is also constrained to 50 Mbps. For general purpose data communication
from 0 to 100 Mbps, the ISO782xLL family of devices should be considered.
The ISO7821LLS device is TIA/EIA-644-A standard compliant. The LVDS transmitter drives a minimum
differential-output voltage magnitude of 250 mV into a 100-Ω load, and the LVDS receiver is capable of detecting
differential signal ≥50 mV in magnitude. The device consumes 11 mA per channel at 150 Mbps with 5-V
supplies.
The Functional Block Diagram section shows a conceptual block diagram of one channel of the ISO7821LLS
device.
8.2 Functional Block Diagram
Transmitter
Receiver
TX Signal
Conditioning
OOK
modulation
IN+
LVDS
RX
IN±
Oscillator
SiO2
based
Capacitive
Isolation
Barrier
RX Signal
Conditioning
EN
Preamplifier
Envelope
Detector
+
Distortion
Correction
OUT+
LVDS
TX
OUT±
Emissions
Reduction
Techniques
Copyright © 2016, Texas Instruments Incorporated
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: ISO7821LLS
17
ISO7821LLS
SLLSET5A – MARCH 2016 – REVISED SEPTEMBER 2016
www.ti.com
8.3 Feature Description
The ISO7821LLS device is available in a two-channel configuration with a default differential-high output state.
Table 1 lists the device features.
Table 1. Device Features
PART
NUMBER
CHANNEL DIRECTION
ISO7821LLS
1 Forward, 1 Reverse
(1)
RATED ISOLATION
5700 VRMS / 8000 VPK
MAXIMUM DATA RATE
DEFAULT DIFFERENTIAL
OUTPUT
150 Mbps
High
(1)
See the Safety-Related Certifications section for detailed isolation ratings.
8.3.1 Distortion-Correction Scheme
The ISO7821LLS device implements a distortion-correction scheme to correct for signal distortions that are
introduced in the LVDS receiver as well as the isolation channel. This scheme is optimized for a DC-balanced
data-stream with a maximum run length of 6. One example of such a data stream is 8b10b encoded data. The
minimum data rate supported by the ISO7821LLS device is 50 Mbps and the maximum is 150 Mbps.
Figure 25 shows the timing requirements associated with the distortion correction scheme (see the Timing
Requirements for Distortion Correction Scheme table for timing parameters). The input to the LVDS channel
should be either idle low, idle high, or should have clock or DC-balanced data transitions at 25 MHz / 50 Mbps or
higher. Low frequency or DC-unbalanced data is not allowed. The distortion-correction scheme runs an internal
calibration each time the LVDS channel transitions from an idle state to a data transmission state. The calibration
runs for a period of tCALIB during which the LVDS channel output is held at logic high. This calibration is also run
at power up. Lack of activity on the receive inputs for a period greater than tIDLE_OUT takes the channel to an
uncalibrated state. If the communication protocol requires the channel to transition to the idle state, the idle-high
or idle-low state must be held for at least duration of tIDLE.
tIDLE
tCALIB
Input to LVDS RX
Output from LVDS TX
tIDLE_OUT
A.
Signals shown are differential logic states.
Logic high → VIN+ > VIN–
Logic low → VIN– > VIN+
B.
The data to ISOLVDS channel should be either idle high, idle low, clock, or valid data.
Valid data = 8b10b like data with DC balance and bounded disparity.
C.
When transitioning from an uncalibrated sate to a calibrated state, the ISOLVDS channel output is gated high for up
to tCALIB, during which the channel is calibrated.
D.
If the channel finds no transitions in the incoming data for a period of tIDLE_OUT, the channel goes to an uncalibrated
state.
E.
Power loss (which implies no data transitions) takes the channel to an uncalibrated state.
F.
If, for some reason, the idle-high or idle-low state must be held on the line, this state must be held for at least tIDLE.
Figure 25. DCD Correction Timing Diagram
18
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: ISO7821LLS
ISO7821LLS
www.ti.com
SLLSET5A – MARCH 2016 – REVISED SEPTEMBER 2016
8.4 Device Functional Modes
Table 2 lists the functional modes for the ISO7821LLS device.
Table 2. ISO7821LLS Function Table (1)
VCCI
VCCO
PU
PU
X
(1)
(2)
(3)
INPUT
(INx±) (2)
OUTPUT ENABLE
(ENx)
OUTPUT
(OUTx±) (3)
H
H or open
H
L
H or open
L
I
H or open
H or L
X
L
Z
A low-logic state at the output enable causes the outputs to be in high
impedance.
Default mode: When VCCI is unpowered, a channel output assumes
the logic high state.
When VCCI transitions from unpowered to powered up, a channel
output assumes the logic state of the input.
When VCCI transitions from powered up to unpowered, a channel
output assumes the selected default high state.
PU
COMMENTS
Normal Operation:
A channel output assumes the logic state of the input.
PD
PU
X
H or open
H
X
PD
X
X
Undetermined
When VCCO is unpowered, a channel output is undetermined.
When VCCO transitions from unpowered to powered up, a channel
output assumes the logic state of the input
VCCI = Input-side VCC; VCCO = Output-side VCC; PU = Powered up (VCCx ≥ 2.25 V); PD = Powered down (VCCx ≤ 1.7 V); X = Irrelevant
Input (INx±): H = high level (VID ≥ 50 mV); L = low level (VID ≤ –50 mV); I = indeterminate (–50 mV < VID < 50 mV)
Output (OUTx±): H = high level (VOD ≥ 250 mV); L = low level (VOD ≤ –250 mV); Z = high impedance.
8.4.1 Device I/O Schematics
LVDS Input
LVDS Output
VCC
600 k
600 k
VCC
INx+
INx±
20
20 k
OUTx
Enable
VCC
275 k
ENx
1k
Figure 26. Device I/O Schematics
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: ISO7821LLS
19
ISO7821LLS
SLLSET5A – MARCH 2016 – REVISED SEPTEMBER 2016
www.ti.com
9 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
9.1 Application Information
The ISO7821LLS device is a high-performance, reinforced isolated dual-LVDS buffer. Isolation can be used to
help achieve human and system safety, to overcome ground potential difference (GPD), or to improve noise
immunity and system performance.
The LVDS signaling can be used over most interfaces to achieve higher data rates because the LVDS is only a
physical layer. LVDS can also be used for a proprietary communication scheme implemented between a host
controller and a slave. Example use cases include connecting a high-speed I/O module to a host controller, a
subsystem connecting to a backplane, and connection between two high-speed subsystems. Many of these
systems operate under harsh environments making them susceptible to electromagnetic interferences, voltage
surges, electrical fast transients (EFT), and other disturbances. These systems must also meet strict limits on
radiated emissions. Using isolation in combination with a robust low-noise signaling standard such as LVDS,
achieves both high immunity to noise and low emissions.
Example end applications that could benefit from the ISO7821LLS device include high-voltage motor control, test
and measurement, industrial automation, and medical equipment.
9.2 Typical Application
One application for isolated LVDS buffers is for point-to-point communication between two high-speed capable,
application-specific integrated circuits (ASICs) or FPGAs. In a high-voltage motor control application, for
example, Node 1 could be a controller on a low-voltage or earth referenced board, and Node 2, could be
controller placed on the power board, biased to high voltage. Figure 27 and Figure 28 show the application
schematics.
Figure 28 provides further details of using the ISO7821LLS device to isolate the LVDS interface. The LVDS
connection to the ISO7821LLS device can be traces on a board (shown as straight lines between Node 1 and
the ISO7821LLS device), a twisted pair cable (as shown between Node 2 and the ISO7821LLS device), or any
other controlled impedance channel. Differential 100-Ω terminations are placed near each LVDS receiver. The
characteristic impedance of the channel should also be 100-Ω differential.
In the example shown in Figure 27 and Figure 28, the ISO7821LLS device provides reinforced or safety isolation
between the high-voltage elements of the motor drive and the low-voltage control circuitry. This configuration
also ensures reliable communication, regardless of the high conducted and radiated noise present in the system.
20
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: ISO7821LLS
ISO7821LLS
www.ti.com
SLLSET5A – MARCH 2016 – REVISED SEPTEMBER 2016
Typical Application (continued)
Isolated IGBT
Gate Drivers
Rectifier Diodes
IGBT Module
DC+
DC±
Drive
Output
Power
Input
M
DC±
PWM
Signals
DC±
ISO7821LLS
Node 2
Node 1
DC±
DC±
Isolated Current
and Voltage Sense
DC±
Communication Bus
RS-485, CAN,
Ethernet
Encoder
High Voltage Motor Drive
Copyright © 2016, Texas Instruments Incorporated
Isolation Barrier
Figure 27. Isolated LVDS Interface in Motor Control Application
VCC1
0.1 F
3.3 V
1
Vcc1
7
EN1
3
Node 1
100 Ÿ
ASIC or FPGA
100 Ÿ
VCC2
0.1 F
3.3 V
16
Vcc2
EN2
10
14
INA+
OUTA+
ISO7821LLS
13
INA±
OUTA±
5
INB± 12
OUTB±
6
INB+ 11
OUTB+
100 Ÿ
4
GND1
2, 8
Node 2
ASIC or FPGA
100 Ÿ
GND2
9, 15
Copyright © 2016, Texas Instruments Incorporated
Figure 28. Isolated LVDS Interface Between Two Nodes (ASIC or FPGA)
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: ISO7821LLS
21
ISO7821LLS
SLLSET5A – MARCH 2016 – REVISED SEPTEMBER 2016
www.ti.com
Typical Application (continued)
9.2.1 Design Requirements
For the ISO7821LLS device, use the parameters listed in Table 3.
Table 3. Design Parameters
PARAMETER
VALUE
Supply voltage range, VCC1 and VCC2
3 V to 5.5 V
Receiver common-mode voltage range
0.5 |VID| to 2.4 – 0.5 |VID|
External termination resistance
100 Ω
Interconnect differential characteristic impedance
100 Ω
Signaling rate
50 to 150 Mbps
Decoupling capacitor from VCC1 and GND1
0.1 µF
Decoupling capacitor from VCC2 and GND2
0.1 µF
9.2.2 Detailed Design Procedure
The ISO7821LLS device has minimum requirements on external components for correct operation. External
bypass capacitors (0.1 µF) are required for both supplies (VCC1 and VCC2). A termination resistor with a value of
100 Ω is required between each differential input pair (INx+ and INx–), with the resistors placed as close to the
device pins as possible. A differential termination resistor with a value of 100 Ω is required on the far end for the
LVDS transmitters. Figure 29 shows these connections.
VCC2
VCC1
1
16
0.1 F
0.1 F
GND2
GND1
2
15
3
14
INA+
LVDS
RX
INA±
4
OUTB±
5
LVDS
TX
OUTB+
Isolation Capacitor
100
OUTA+
LVDS
TX
OUTA±
13
INB±
12
LVDS
RX
INB+
6
11
7
10
8
9
100
EN2
EN1
GND1
GND2
Figure 29. Typical ISO7821LLS Circuit Hook-Up
22
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: ISO7821LLS
ISO7821LLS
www.ti.com
SLLSET5A – MARCH 2016 – REVISED SEPTEMBER 2016
9.2.2.1 Electromagnetic Compatibility (EMC) Considerations
Many applications in harsh industrial environment are sensitive to disturbances such as electrostatic discharge
(ESD), electrical fast transient (EFT), surge and electromagnetic emissions. These electromagnetic disturbances
are regulated by international standards such as IEC 61000-4-x and CISPR 22. Although system-level
performance and reliability depends, to a large extent, on the application board design and layout, the
ISO7821LLS device incorporates many chip-level design improvements for overall system robustness. Some of
these improvements include:
• Robust ESD protection cells for input and output signal pins and inter-chip bond pads.
• Low-resistance connectivity of ESD cells to supply and ground pins.
• Enhanced performance of high voltage isolation capacitor for better tolerance of ESD, EFT and surge events.
• Bigger on-chip decoupling capacitors to bypass undesirable high energy signals through a low impedance
path.
• PMOS and NMOS devices isolated from each other by using guard rings to avoid triggering of parasitic
SCRs.
• Reduced common mode currents across the isolation barrier by ensuring purely differential internal operation.
9.2.3 Application Curve
Figure 30 shows a typical eye diagram of the ISO7821LLS device which indicates low jitter and a wide-open eye
at the maximum data rate of 150 Mbps.
Figure 30. Eye Diagram at 150 Mbps PRBS, 3.3 V and 25°C
10 Power Supply Recommendations
To help ensure reliable operation at data rates and supply voltages, a 0.1-μF bypass capacitor is recommended
at the input and output supply pins (VCC1 and VCC2). The capacitors should be placed as close to the supply pins
as possible. If only a single primary-side power supply is available in an application, isolated power can be
generated for the secondary-side with the help of a transformer driver such as Texas Instruments' SN6501 or
SN6505. For such applications, detailed power supply design and transformer selection recommendations are
available in the following data sheets: SN6501 Transformer Driver for Isolated Power Supplies (SLLSEA0) and
SN6505 Low-Noise 1-A Transformer Drivers for Isolated Power Supplies (SLLSEP9).
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: ISO7821LLS
23
ISO7821LLS
SLLSET5A – MARCH 2016 – REVISED SEPTEMBER 2016
www.ti.com
11 Layout
11.1 Layout Guidelines
A minimum of four layers is required to accomplish a low EMI PCB design (see Figure 31). Layer stacking should
be in the following order (top-to-bottom): high-speed signal layer, ground plane, power plane and low-frequency
signal layer.
• Routing the high-speed traces on the top layer avoids the use of vias (and the introduction of their
inductances) and allows for clean interconnects between the isolator and the transmitter and receiver circuits
of the data link.
• Placing a solid ground plane next to the high-speed signal layer establishes controlled impedance for
transmission line interconnects and provides an excellent low-inductance path for the return current flow.
• Placing the power plane next to the ground plane creates additional high-frequency bypass capacitance of
approximately 100 pF/in2.
• Routing the slower speed control signals on the bottom layer allows for greater flexibility as these signal links
usually have margin to tolerate discontinuities such as vias.
• While routing differential traces on a board, TI recommends that the distance between two differential pairs be
much higher (at least 2x) than the distance between the traces in a differential pair. This distance minimizes
crosstalk between the two differential pairs.
If an additional supply voltage plane or signal layer is needed, add a second power or ground plane system to
the stack to keep it symmetrical. This makes the stack mechanically stable and prevents it from warping. Also the
power and ground plane of each power system can be placed closer together, thus increasing the high-frequency
bypass capacitance significantly.
The ISO7821LLS device requires no special layout considerations to mitigate electromagnetic emissions.
For detailed layout recommendations, see the application note, Digital Isolator Design Guide (SLLA284).
11.1.1 PCB Material
For digital circuit boards operating at less than 150 Mbps (or rise and fall times higher than 1 ns) and trace
lengths of up to 10 inches, use standard FR–4 UL94V-0 epoxy-glass as PCB material. This PCB is preferred
over cheaper alternatives because of lower dielectric losses at high frequencies, less moisture absorption,
greater strength and stiffness, and self-extinguishing flammability-characteristics.
11.2 Layout Example
High-speed traces
10 mils
Ground plane
40 mils
Keep this
space free
from planes,
traces, pads,
and vias
FR-4
0r ~ 4.5
Power plane
10 mils
Low-speed traces
Figure 31. Layout Example
24
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: ISO7821LLS
ISO7821LLS
www.ti.com
SLLSET5A – MARCH 2016 – REVISED SEPTEMBER 2016
12 Device and Documentation Support
12.1 Documentation Support
12.1.1 Related Documentation
For related documentation see the following:
• Digital Isolator Design Guide (SLLA284)
• ISO782xLLx Isolated Dual LVDS Buffer Evaluation Module (SLLU240)
• Isolation Glossary (SLLA353)
• LVDS Owner’s Manual (SNLA187)
• SN6501 Transformer Driver for Isolated Power Supplies (SLLSEA0)
• SN6505 Low-Noise 1-A Transformer Drivers for Isolated Power Supplies (SLLSEP9)
12.2 Receiving Notification of Documentation Updates
To receive notification of documentation updates — go to the product folder for your device on ti.com. In the
upper right-hand corner, click the Alert me button to register and receive a weekly digest of product information
that has changed (if any). For change details, check the revision history of any revised document.
12.3 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
12.4 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
12.5 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
12.6 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
13 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: ISO7821LLS
25
PACKAGE OPTION ADDENDUM
www.ti.com
23-Dec-2016
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
ISO7821LLSDW
ACTIVE
SOIC
DW
16
40
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-55 to 125
ISO7821LLS
ISO7821LLSDWR
ACTIVE
SOIC
DW
16
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-55 to 125
ISO7821LLS
ISO7821LLSDWW
ACTIVE
SOIC
DWW
16
45
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-55 to 125
ISO7821LLS
ISO7821LLSDWWR
ACTIVE
SOIC
DWW
16
1000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-55 to 125
ISO7821LLS
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
23-Dec-2016
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
22-Dec-2016
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
ISO7821LLSDWR
SOIC
DW
16
2000
330.0
16.4
10.75
10.7
2.7
12.0
16.0
Q1
ISO7821LLSDWWR
SOIC
DWW
16
1000
330.0
24.4
18.0
10.0
3.0
20.0
24.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
22-Dec-2016
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
ISO7821LLSDWR
ISO7821LLSDWWR
SOIC
DW
16
2000
367.0
367.0
38.0
SOIC
DWW
16
1000
367.0
367.0
45.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2016, Texas Instruments Incorporated