ATMEL ATA5428 Uhf ask/fsk transceiver Datasheet

Features
• Multi Channel Half-duplex Transceiver with Approximately ±2.5 MHz Programmable
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Tuning Range
High FSK Sensitivity: –106 dBm at 20 Kbit/s/–109.5 dBm at 2.4 Kbit/s (433.92 MHz)
High ASK Sensitivity: –112.5 dBm at 10 Kbit/s/–116.5 dBm at 2.4 Kbit/s (433.92 MHz)
Low Supply Current: 10.5 mA in RX and TX Mode (3V/TX with 5 dBm)
Data Rate: 1 to 20 Kbit/s Manchester FSK, 1 to 10 Kbit/s Manchester ASK
ASK/FSK Receiver Uses a Low-IF Architecture with High Selectivity, Blocking, and Low
Intermodulation (Typical Blocking 55 dB at ±750 kHz/61 dB at ±1.5 MHz and
70 dB at ±10 MHz, System I1dBCP = –30 dBm/System IIP3 = –20 dBm)
226 kHz/237 kHz IF Frequency with 30 dB Image Rejection and 170 kHz Usable IF
Bandwidth
Transmitter Uses Closed Loop Fractional-N Synthesizer for FSK Modulation with a
High PLL Bandwidth and an Excellent Isolation between PLL/VCO and PA
Tolerances of XTAL Compensated by Fractional-N Synthesizer with 800 Hz RF
Resolution
Integrated RX/TX-Switch, Single-ended RF Input and Output
RSSI (Received Signal Strength Indicator)
Communication to Microcontroller with SPI Interface Working at Maximum 500 kBit/s
Configurable Self Polling and RX/TX Protocol Handling with FIFO-RAM Buffering of
Received and Transmitted Data
5 Push Button Inputs and One Wake-up Input are Active in Power-down Mode
Integrated XTAL Capacitors
PA Efficiency: up to 38% (433.92 MHz/10 dBm/3V)
Low In-band Sensitivity Change of Typically ±1.8 dB within ±58 kHz Center Frequency
Change in the Complete Temperature and Supply Voltage Range
Supply Voltage Switch, Supply Voltage Regulator, Reset Generation, Clock/Interrupt
Generation and Low Battery Indicator for Microcontroller
Fully Integrated PLL with Low Phase Noise VCO, PLL Loop Filter and Full Support of
Multi-channel Operation with Arbitrary Channel Distance Due to Fractional-N
Synthesizer
Sophisticated Threshold Control and Quasi-peak Detector Circuit in the Data Slicer
Power Management via Different Operation Modes
315 MHz, 345 MHz, 433.92 MHz, 868.3 MHz and 915 MHz without External VCO and PLL
Components
Inductive Supply with Voltage Regulator if Battery is Empty (AUX Mode)
Efficient XTO Start-up Circuit (> –1.5 kΩ Worst Case Real Start-up Impedance)
Changing of Modulation Type ASK/FSK and Data Rate without Component Changes
Minimal External Circuitry Requirements for Complete System Solution
Adjustable Output Power: 0 to 10 dBm Adjusted and Stabilized with External Resistor
ESD Protection at all Pins (1.5 kV HBM, 200V MM, 1 kV FCDM)
Supply Voltage Range: 2.4V to 3.6V or 4.4V to 6.6V
Temperature Range: –40°C to +85°C
Small 7 × 7 mm QFN48 Package
UHF ASK/FSK
Transceiver
ATA5423
ATA5425
ATA5428
ATA5429
4841D–WIRE–10/07
Applications
•
•
•
•
•
•
Consumer Industrial Segment
Access Control Systems
Remote Control Systems
Alarm and Telemetry Systems
Energy Metering
Home Automation
Benefits
• Low System Cost Due to Very High System Integration Level
• Only One Crystal Needed in System
• Less Demanding Specification for the Microcontroller Due to Handling of Power-down Mode,
Delivering of Clock, Reset, Low Battery Indication and Complete Handling of Receive/Transmit
Protocol and Polling
• Single-ended Design with High Isolation of PLL/VCO from PA and the Power Supply Allows a
Loop Antenna in the Remote Control Unit to Surround the Whole Application
2
ATA5423/ATA5425/ATA5428/ATA5429
4841D–WIRE–10/07
ATA5423/ATA5425/ATA5428/ATA5429
1. General Description
The ATA5423/25/28/29 is a highly integrated UHF ASK/FSK multi-channel half-duplex transceiver with low power consumption supplied in a small 7 x 7 mm QFN48 package. The receive
part is built as a fully integrated low-IF receiver, whereas direct PLL modulation with the fractional-N synthesizer is used for FSK transmission and switching of the power amplifier for ASK
transmission.
The device supports data rates of 1 Kbit/s to 20 Kbit/s (FSK) and 1 Kbit/s to 10 Kbit/s (ASK) in
Manchester, Bi-phase and other codes in transparent mode. The ATA5428 can be used in the
431.5 MHz to 436.5 MHz and in the 862 MHz to 872 MHz bands, the ATA5423 in the 312.5 MHz
to 317.5 MHz band, the ATA5425 in the 342.5 MHz to 347.5 MHz band and the ATA5429 in the
912.5 MHz to 917.5 MHz band. The very high system integration level results in a small number
of external components needed.
Due to its blocking and selectivity performance, together with the additional 15 dB to 20 dB loss
and the narrow bandwidth of a typical loop antenna in a remote control unit, a bulky blocking
SAW is not needed in the remote control unit. Additionally, the building blocks needed for a typical remote control and access control system on both sides (the base and the mobile stations)
are fully integrated.
Its digital control logic with self-polling and protocol generation enables a fast challengeresponse system without using a high-performance microcontroller. Therefore, the
ATA5423/ATA5425/ATA5428/ATA5429 contains a FIFO buffer RAM and can compose and
receive the physical messages themselves. This provides more time for the microcontroller to
carry out other functions such as calculating crypto algorithms, composing the logical messages,
and controlling other devices. Therefore, a standard 4-/8-bit microcontroller without special
periphery and clocked with the CLK output of about 4.5 MHz is sufficient to control the communication link. This is especially valid for passive entry and access control systems, where within
less than 100 ms several challenge-response communications with arbitration of the communication partner have to be handled.
It is hence possible to design bi-directional remote control and access control systems with a
fast challenge-response crypto function, with the same PCB board size and with the same current consumption as uni-directional remote control systems.
3
4841D–WIRE–10/07
Figure 1-1.
System Block Diagram
ATA5423/ATA5425/ATA5428/ATA5429
RF Transceiver
Antenna
Digital Control
Logic
Power
Supply
ATmega
44/88/168
Microcontroller
interface
Matching/
RF Switch
4 to 8
XTO
CDEM
RX_TX2
PWR_ON
RX_TX1
T5
T3
T4
T2
RX_ACTIVE
T1
NC
Pinning QFN48
NC
Figure 1-2.
48 47 46 45 44 43 42 41 40 39 38 37
NC
1
36
RSSI
NC
2
35
CS
NC
3
34
DEM_OUT
RF_IN
4
33
SCK
NC
5
32
SDI_TMDI
433_N868
6
31
SDO_TMDO
NC
7
30
CLK
R_PWR
8
29
IRQ
PWR_H
9
28
N_RESET
RF_OUT
10
27
VSINT
NC
11
26
NC
NC
12
25
13 14 15 16 17 18 19 20 21 22 23 24
4
XTAL2
TXAL1
TEST2
DVCC
VSOUT
TEST1
VS1
VAUX
VS2
NC
AVCC
NC
NC
ATA5423/ATA5425
ATA5428/ATA5429
ATA5423/ATA5425/ATA5428/ATA5429
4841D–WIRE–10/07
ATA5423/ATA5425/ATA5428/ATA5429
Table 1-1.
Pin Description
Pin
Symbol
1
NC
Not connected
Function
2
NC
Not connected
3
NC
Not connected
4
RF_IN
5
NC
6
433_N868
7
NC
8
R_PWR
Resistor to adjust output power
9
PWR_H
Pin to select output power
10
RF_OUT
RF output
11
NC
Not connected
12
NC
Not connected
13
NC
Not connected
14
NC
Not connected
15
NC
Not connected
16
AVCC
17
VS2
Power supply input for voltage range 4.4V to 6.6V
18
VS1
Power supply input for voltage range 2.4V to 3.6V
19
VAUX
Auxiliary supply voltage input
20
TEST1
Test input, at GND during operation
RF input
Not connected
Selects RF input/output frequency range
Not connected
Blocking of the analog voltage supply
21
DVCC
22
VSOUT
Output voltage power supply for external devices
Blocking of the digital voltage supply
23
TEST2
Test input, at GND during operation
24
XTAL1
Reference crystal
25
XTAL2
Reference crystal
26
NC
27
VSINT
28
N_RESET
Not connected
Microcontroller interface supply voltage
Output pin to reset a connected microcontroller
29
IRQ
Interrupt request
30
CLK
Clock output to connect a microcontroller
31
SDO_TMDO
Serial data out/transparent mode data out
32
SDI_TMDI
33
SCK
34
DEM_OUT
35
CS
36
RSSI
Serial data in/transparent mode data in
Serial clock
Demodulator open drain output signal
Chip select for serial interface
Output of the RSSI amplifier
Capacitor to adjust the lower cut-off frequency data filter
37
CDEM
38
RX_TX2
GND pin to decouple LNA in TX mode
39
RX_TX1
Switch pin to decouple LNA in TX mode
40
PWR_ON
41
T5
Input to switch on the system (active high)
Key input 5 (can also be used to switch on the system (active low))
5
4841D–WIRE–10/07
Table 1-1.
Pin Description (Continued)
Pin
Symbol
42
T4
Key input 4 (can also be used to switch on the system (active low))
43
T3
Key input 3 (can also be used to switch on the system (active low))
44
T2
Key input 2 (can also be used to switch on the system (active low))
45
T1
Key input 1 (can also be used to switch on the system (active low))
46
RX_ACTIVE
47
NC
Not connected
48
NC
Not connected
GND
Figure 1-3.
Function
Indicates RX operation mode
Ground/backplane
Block Diagram
AVCC
433_N868
RX_ACTIVE
RF transceiver
DVCC
Digital Control Logic
Power
Supply
Frontend Enable
R_PWR
PA
RX_TX1
RX/TX
switch
RX_TX2
RF_IN
VSOUT
TX_DATA (FSK)
Switches
Regulators
Wake-up
Reset
RX/TX
PWR_H
LNA
CDEM
Fractional-N
frequency
synthesizer
Signal
Processing
(Mixer
IF-filter
IF-amplifier
FSK/ASK
Demodulator,
Data filter
Data Slicer)
13
FREQ
VS1
VAUX
PA_Enable (ASK)
RF_OUT
VS2
FREF
PWR_ON
T1
Demod_Out
TX/RX - Data buffer
Control register
Status register
Polling circuit
Bit-check logic
T2
T3
T4
T5
Reset
RSSI
XTAL1
XTO
XTAL2
DEM_OUT
CLK
TEST1
N_RESET
TEST2
IRQ
CS
Microcontroller
interface
SCK
SPI
SDI_TMDI
SDO_TMDO
VSINT
6
GND
ATA5423/ATA5425/ATA5428/ATA5429
4841D–WIRE–10/07
ATA5423/ATA5425/ATA5428/ATA5429
2. Application Circuits
2.1
Typical Remote Control Unit Application with 1 Li Battery (3V)
Figure 2-1 shows a typical 433.92 MHz Remote Control Unit application with one battery. The
external components are 11 capacitors, 1 resistor, 2 inductors and a crystal. C1 to C4 are 68 nF
voltage supply blocking capacitors. C5 is a 10 nF supply blocking capacitor. C6 is a 15 nF fixed
capacitor used for the internal quasi-peak detector and for the high-pass frequency of the data
filter. C7 to C11 are RF matching capacitors in the range of 1 pF to 33 pF. L1 is a matching inductor of about 5.6 nH to 56 nH. L2 is a feed inductor of about 120 nH. A load capacitor of 9 pF for
the crystal is integrated. R1 is typically 22 kΩ and sets the output power to about 5.5 dBm. The
loop antenna’s quality factor is somewhat reduced by this application due to the quality factor of
L2 and the RX/TX switch. On the other hand, this lower quality factor is necessary to have a
robust design with a bandwidth that is broad enough for production tolerances. Due to the single-ended and ground-referenced design, the loop antenna can be a free-form wire around the
application as it is usually employed in remote control uni-directional systems. The
ATA5423/ATA5425/ATA5428/ATA5429 provides sufficient isolation and robust pulling behavior
of internal circuits from the supply voltage as well as an integrated VCO inductor to allow this.
Since the efficiency of a loop antenna is proportional to the square of the surrounded area it is
beneficial to have a large loop around the application board with a lower quality factor in order to
relax the tolerance specification of the RF components and to get a high antenna efficiency in
spite of their lower quality factor.
Typical Remote Control Unit Application, 433.92 MHz, 1 Li Battery (3V)
C11
C7
C6
NC
RX_TX2
RX_TX1
T4
T3
T2
T5
PWR_ON
NC
NC
T1
NC
Sensor
RX_ACTIVE
CDEM
RSSI
CS
DEM_OUT
RF_IN
SCK
NC
433_N868
R1
L2
NC
ATA5423/ATA5425 SDO_TMDO
CLK
ATA5428/ATA5429
R_PWR
IRQ
PWR_H
N_RESET
RF_OUT
Loop antenna
VSOUT
DVCC
TEST1
VAUX
VS1
VS2
AVCC
NC
C9
NC
NC
C10
VCC
VSINT
NC
NC
C8
ATmega
48/88/168
SDI_TMDI
TEST2
AVCC
C5
VSS
NC
TXAL1
20 mm x 0.4 mm
L1
NC
Figure 2-1.
XTAL2
C1
C4
13.25311 MHz
C2
+ Lithium cell
C3
7
4841D–WIRE–10/07
2.2
Typical Base-station Application (5V)
Figure 2.2 shows a typical 433.92 MHz VCC = 4.75V to 5.25V Base-station Application (5V). The
external components are 12 capacitors, 1 resistor, 4 inductors, a SAW filter, and a crystal. C1
and C3 to C4 are 68 nF voltage supply blocking capacitors. C2 and C12 are 2.2 µF supply blocking capacitors for the internal voltage regulators. C5 is a 10 nF supply blocking capacitor. C6 is a
15 nF fixed capacitor used for the internal quasi-peak detector and for the high-pass frequency
of the data filter. C7 to C11 are RF matching capacitors in the range of 1 pF to 33 pF. L2 to L4 are
matching inductors of about 5.6 nH to 56 nH. A load capacitor for the crystal of 9 pF is integrated. R1 is typically 22 kΩ and sets the output power at RF_OUT to about 10 dBm. Since a
quarter wave or PCB antenna, which has high efficiency and wide band operation, is typically
used here, it is recommended to use a SAW filter to achieve high sensitivity in case of powerful
out-of-band blockers. L1, C9 and C10 together form a low-pass filter, which is needed to filter out
the harmonics in the transmitted signal to meet regulations. An internally regulated voltage at pin
VSOUT can be used in case the microcontroller only supports 3.3V operation, a blocking capacitor with a value of C12 = 2.2 µF has to be connected to VSOUT in any case.
Typical Base-station Application (5V), 433.92 MHz
L3
C7
NC
RX_TX2
RX_TX1
T4
T3
T2
T5
PWR_ON
NC
NC
T1
Sensor
NC
CDEM
RSSI
CS
DEM_OUT
RF_IN
SCK
NC
433_N868
L2
RFOUT
ATA5423/ATA5425 SDO_TMDO
CLK
ATA5428/ATA5429
R_PWR
IRQ
PWR_H
N_RESET
RF_OUT
C10
VSOUT
DVCC
TEST1
VAUX
VS1
VS2
AVCC
C8
NC
L1
VCC
VSINT
NC
NC
NC
50Ω
connector
NC
TEST2
R1
ATmega
48/88/168
SDI_TMDI
NC
AVCC
C5
XTAL2
C9
C12
C1
C2
13.25311 MHz
C4
VCC = 4.75V to 5.25V
8
VSS
NC
TXAL1
SAW-Filter
C6
RX_ACTIVE
C11
NC
L4
20 mm x 0.4 mm
Figure 2-2.
C3
ATA5423/ATA5425/ATA5428/ATA5429
4841D–WIRE–10/07
ATA5423/ATA5425/ATA5428/ATA5429
2.3
Typical Remote Control Unit Application, 2 Li Batteries (6V)
Figure 2-3 shows a typical 433.92 MHz 2 Li battery Remote Control Unit application. The external components are 11 capacitors, 1 resistor, 2 inductors and a crystal. C1 and C4 are 68 nF
voltage supply blocking capacitors. C2 and C3 are 2.2 µF supply blocking capacitors for the internal voltage regulators. C5 is a 10 nF supply blocking capacitor. C6 is a 15 nF fixed capacitor
used for the internal quasi-peak detector and for the high-pass frequency of the data filter. C7 to
C11 are RF matching capacitors in the range of 1 pF to 33 pF. L1 is a matching inductor of about
5.6 nH to 56 nH. L2 is a feed inductor of about 120 nH. A load capacitor for the crystal of 9 pF is
integrated. R1 is typically 22 kΩ and sets the output power to about 5.5 dBm.
Typical Remote Control Unit Application, 433.92 MHz, 2 Li Batteries (6V)
C11
C7
C6
NC
RX_TX2
RX_TX1
T4
T3
T2
T5
PWR_ON
NC
NC
T1
NC
Sensor
RX_ACTIVE
CDEM
RSSI
CS
DEM_OUT
RF_IN
SCK
NC
433_N868
R1
L2
NC
ATA5423/ATA5425 SDO_TMDO
CLK
ATA5428/ATA5429
R_PWR
IRQ
PWR_H
N_RESET
RF_OUT
Loop antenna
C1
VSOUT
DVCC
TEST1
VAUX
VS1
VS2
AVCC
NC
C9
NC
NC
C10
VCC
VSINT
NC
NC
C8
ATmega
48/88/168
SDI_TMDI
TEST2
AVCC
C5
VSS
NC
TXAL1
20 mm x 0.4 mm
L1
NC
Figure 2-3.
XTAL2
C2
C4
+ Lithium cell
13.25311 MHz
C3
+ Lithium cell
9
4841D–WIRE–10/07
3. RF Transceiver
As seen in Figure 1-3 on page 6, the RF transceiver consists of an LNA (Low-noise Amplifier),
PA (Power Amplifier), RX/TX switch, fractional-N frequency synthesizer and the signal processing part with mixer, IF filter, IF amplifier with analog RSSI, FSK/ASK demodulator, data filter, and
data slicer.
In receive mode the LNA pre-amplifies the received signal which is converted down to 226 kHz
(ATA5423/ATA5428) and 235 kHz (ATA5425/ATA5429), filtered and amplified before it is fed
into an FSK/ASK demodulator, data filter, and data slicer. The RSSI (Received Signal Strength
Indicator) signal and the raw digital output signal of the demodulator are available at the pins
RSSI and DEM_OUT. The demodulated data signal Demod_Out is fed to the digital control logic
where it is evaluated and buffered as described in the section “Digital Control Logic” .
In transmit mode, the fractional-N frequency synthesizer generates the TX frequency which is
fed to the PA. In ASK mode the PA is modulated by the signal PA_Enable. In FSK mode the PA
is enabled and the signal TX_DATA (FSK) modulates the fractional-N frequency synthesizer.
The frequency deviation is digitally controlled and internally fixed to about ±16 kHz (see Table
4-1 on page 28 for exact values). The transmit data can also be buffered as described in the
section “Digital Control Logic” . A lock detector within the synthesizer ensures that the transmission will start only if the synthesizer is locked.
The RX/TX switch can be used to combine the LNA input and the PA output to a single antenna
with a minimum of losses.
Transparent modes without buffering of RX and TX data are also available to allow protocols
and coding schemes other than the internally supported Manchester encoding.
3.1
Low-IF Receiver
The receive path consists of a fully integrated low-IF receiver. It fulfills the sensitivity, blocking,
selectivity, supply voltage and supply current specification needed to manufacture, for example,
an automotive remote control unit without the use of SAW blocking filter (see Figure 2-1 on page
7). In a Base-station Application (5V) the receiver can be used with an additional blocking SAW
front-end filter as shown in Figure 2.2 on page 8.
At 433.92 MHz the receiver has a typical system noise figure of 7.0 dB, a system I1dBCP of
-30 dBm and a system IIP3 of –20 dBm. There is no AGC or switching of the LNA needed; thus,
a better blocking performance is achieved. This receiver uses an IF (Intermediate Frequency) of
226 kHz, the typical image rejection is 30 dB and the typical 3 dB IF filter bandwidth is 185 kHz
(fIF = 226 kHz ±92.5 kHz, flo_IF = 133.5 kHz and fhi_IF = 318.5 kHz). The demodulator needs a
signal to Gaussian noise ratio of 8 dB for 20 Kbit/s Manchester with ±16 kHz frequency deviation
in FSK mode; thus, the resulting sensitivity at 433.92 MHz is typically –106 dBm at 20 Kbit/s
Manchester.
Due to the low phase noise and spurious emissions of the synthesizer in receive mode (1)
together with the eighth order integrated IF filter, the receiver has a better selectivity and blocking performance than more complex double superhet receivers but without external components
and without numerous spurious receiving frequencies.
10
ATA5423/ATA5425/ATA5428/ATA5429
4841D–WIRE–10/07
ATA5423/ATA5425/ATA5428/ATA5429
A low-IF architecture is also less sensitive to second-order intermodulation (IIP2) than direct
conversion receivers, where every pulse or AM-modulated signal (especially the signals from
TDMA systems like GSM) demodulates to the receiving signal band at second-order
non-linearities.
Note:
3.2
–120 dBC/Hz at ±1 MHz and –75 dBC at ±FREF at 433.92 MHz
Input Matching at RF_IN
The measured input impedances as well as the values of a parallel equivalent circuit of these
impedances can be seen in Table 3-1. The highest sensitivity is achieved with power matching
of these impedances to the source impedance of 50Ω
Table 3-1.
Measured Input Impedances of the RF_IN Pin
fRF/MHz
Z(RF_IN)
Rp//Cp
315
(44-j233)Ω
1278Ω//2.1 pF
345
(40-j211)Ω
1153Ω//2.1 pF
433.92
(32-j169)Ω
925Ω//2.1 pF
868.3
(21-j78)Ω
311Ω//2.2 pF
915
(18-j70)Ω
290Ω//2.3 pF
The matching of the LNA Input to 50Ω was done with the circuit shown in Figure 3-1 and with the
values given in Table 3-2 on page 12. The reflection coefficients were always ≤10 dB. Note that
value changes of C1 and L1 may be necessary to compensate for individual board layouts. The
measured typical FSK and ASK Manchester code sensitivities with a Bit Error Rate (BER) of 10-3
are shown in Table 3-3 and Table 3-4 on page 12. These measurements were done with inductors having a quality factor according to Table 3-2, resulting in estimated matching losses of
0.8 dB at 315 MHz, 0.8 dB at 345 MHz, 0.7 dB at 433.92 MHz, 0.7 dB at 868.3 MHz and 0.7 at
915 MHz. These losses can be estimated when calculating the parallel equivalent resistance of
the inductor with Rloss = 2 × π × f × L × QL and the matching loss with 10 log(1 + Rp/Rloss).
With an ideal inductor, for example, the sensitivity at 433.92 MHz/FSK/20 Kbit/s/
±16 kHz/Manchester can be improved from –106 dBm to –106.7 dBm. The sensitivity depends
on the control logic which examines the incoming data stream. The examination limits must be
programmed in control registers 5 and 6. The measurements in Table 3-3 and Table 3-4 on
page 12 are based on the values of registers 5 and 6 according to Table 9-3 on page 61.
Figure 3-1.
Input Matching to 50Ω
C1
4
ATA5423/ATA5425
ATA5428/ATA5429
RF_IN
L1
11
4841D–WIRE–10/07
Table 3-2.
Input Matching to 50Ω
fRF/MHz
C1/pF
L1/nH
QL1
315
2.4
47
66
345
1.8
43
67
433.92
1.8
27
70
868.3
1.2
6.8
50
915
1.3
5.6
52
Table 3-3.
RF
Frequency
BR_Range_0
1.0 Kbit/s
BR_Range_0
2.4 Kbit/s
BR_Range_1
5.0 Kbit/s
BR_Range_2
10 Kbit/s
BR_Range_3
20 Kbit/s
315 MHz
–110.0 dBm
–110.5 dBm
–109.0 dBm
–108.0 dBm
–107.0 dBm
345 MHz
–109.5 dBm
–110.5 dBm
–109.0 dBm
–107.5 dBm
–107.0 dBm
433.92 MHz
–109.0 dBm
–109.5 dBm
–108.0 dBm
–107.0 dBm
–106.0 dBm
868.3 MHz
–106.0 dBm
–106.5 dBm
–105.5 dBm
–104.0 dBm
–103.5 dBm
915 MHz
–105.5 dBm
–106.0 dBm
–105.0 dBm
–103.5 dBm
–103.0 dBm
Table 3-4.
3.3
Measured Sensitivity FSK, ±16 kHz, Manchester, dBm, BER = 10–3
Measured Sensitivity 100% ASK, Manchester, dBm, BER = 10–3
RF Frequency
BR_Range_0
1.0 Kbit/s
BR_Range_0
2.4 Kbit/s
BR_Range_1
5.0 Kbit/s
BR_Range_2
10 Kbit/s
315 MHz
–117.0 dBm
–117.5 dBm
–115.0 dBm
–113.5 dBm
345 MHz
–117.0 dBm
–117.5 dBm
–115.0 dBm
–113.0 dBm
433.92 MHz
–116.0 dBm
–116.5 dBm
–114.0 dBm
–112.5 dBm
868.3 MHz
–112.5 dBm
–113.0 dBm
–111.5 dBm
–109.5 dBm
915 MHz
–112.5 dBm
–113.0 dBm
–111.0 dBm
–109.0 dBm
Sensitivity versus Supply Voltage, Temperature and Frequency Offset
To calculate the behavior of a transmission system it is important to know the reduction of the
sensitivity due to several influences. The most important are frequency offset due to crystal
oscillator (XTO) and crystal frequency (XTAL) errors, temperature and supply voltage dependency of the noise figure and IF filter bandwidth of the receiver. Figure 3-2 shows the typical
sensitivity at 433.92 MHz/FSK/20 Kbit/s/±16 kHz/Manchester versus the frequency offset
between transmitter and receiver with Tamb = –40°C, +25°C and +105°C and supply voltage
VS1 = VS2 = 2.4V, 3.0V and 3.6V.
12
ATA5423/ATA5425/ATA5428/ATA5429
4841D–WIRE–10/07
ATA5423/ATA5425/ATA5428/ATA5429
Figure 3-2.
Measured Sensitivity 433.92 MHz/FSK/20 Kbit/s/±16 kHz/Manchester versus
Frequency Offset, Temperature and Supply Voltage
-110
-109
-108
Sensitivity (dBm)
-107
-106
-105
-104
-103
-102
-101
-100
-99
-98
-97
-96
-95
-100
VS = 2.4V Tamb = -40°C
VS = 3.0V Tamb = -40°C
VS = 3.6V Tamb = -40°C
VS = 2.4V Tamb = +25°C
VS = 3.0V Tamb = +25°C
VS = 3.6V Tamb = +25°C
VS = 2.4V Tamb = +105°C
VS = 3.0V Tamb = +105°C
VS = 3.6V Tamb = +105°C
-80
-60
-40
-20
0
20
40
Frequency Offset (kHz)
60
80
100
As can be seen in Figure 3-2 on page 13 the supply voltage has almost no influence. The temperature has an influence of about +1.5/–0.7 dB, and a frequency offset of ±65 kHz also
influences by about ±1 dB. All these influences, combined with the sensitivity of a typical IC, are
then within a range of –103.7 dBm and –107.3 dBm over temperature, supply voltage and frequency offset which is –105.5 dBm ±1.8dB. The integrated IF filter has an additional production
tolerance of only ±7 kHz, hence, a frequency offset between the receiver and the transmitter of
±58 kHz can be accepted for XTAL and XTO tolerances.
Note:
For the demodulator used in the ATA5423/ATA5425, the tolerable frequency offset does not
change with the data frequency, hence, the value of ±58 kHz is valid for up to 1 Kbit/s.
This small sensitivity spread over supply voltage, frequency offset and temperature is very
unusual in such a receiver. It is achieved by an internal, very fast and automatic frequency correction in the FSK demodulator after the IF filter, which leads to a higher system margin. This
frequency correction tracks the input frequency very quickly; if, however, the input frequency
makes a larger step (for example, if the system changes between different communication partners), the receiver has to be restarted. This can be done by switching back to IDLE mode and
then again to RX mode. For that purpose, an automatic mode is also available. This automatic
mode switches to IDLE mode and back into RX mode every time a bit error occurs. (See “Digital
Control Logic” on page 36.)
13
4841D–WIRE–10/07
3.4
Frequency Accuracy of the Crystals
The XTO is an amplitude regulated Pierce oscillator with integrated load capacitors. The initial
tolerances (due to the frequency tolerance of the XTAL, the integrated capacitors on XTAL1,
XTAL2 and the XTO’s initial transconductance gm) can be compensated to a value within
±0.5 ppm by measuring the CLK output frequency and programming the control registers 2 and
3 (see Table 7-7 on page 39 and Table 7-10 on page 40). The XTO then has a remaining influence of less than ±2 ppm over temperature and supply voltage due to the band gap controlled
gm of the XTO.
The needed frequency stability of the used crystals over temperature and aging is hence
±58 kHz/315 MHz – 2 × ±2.5 ppm = ±179.2 ppm for 315 MHz,
±58 kHz/345 MHz – 2 × ±2.5 ppm = ±163.2 ppm for 345 MHz,
±58 kHz/433.92 MHz – 2 × ±2.5 ppm = ±128.6 ppm for 433.92 MHz,
±58 kHz/868.3 MHz – 2 × ±2.5 ppm = ±61.8 ppm for 868.3 MHz and
±58 kHz/915 MHz – 2 × ±2.5 ppm = ±58.4 ppm for 915 MHz.
Thus, the used crystals in receiver and transmitter each need to be better than ±89.6 ppm for
315 MHz, ±81.6 ppm for 345 MHz, ±64.3 ppm for 433.92 MHz, ±30.9 ppm for 868.3 MHz and
±29.2 ppm for 915 MHz. In access control systems it may be advantageous to have a more tight
tolerance at the Base-station in order to relax the requirement for the remote control unit.
3.5
RX Supply Current versus Temperature and Supply Voltage
Table 3-5 shows the typical supply current at 433.92 MHz of the transceiver in RX mode versus
supply voltage and temperature with VS = VS1 = VS2. As can be seen, the supply current at
2.4 V and –40°C is less than the typical supply current; this is useful because this is also the
operation point where a lithium cell has the worst performance. The typical supply current at
315 MHz, 345 MHz, 868.3 MHz or 915 MHz in RX mode is about the same as for 433.92 MHz.
Table 3-5.
3.6
Measured 433.92 MHz Receive Supply Current in FSK Mode
VS = VS1 = VS2
2.4V
3.0V
3.6V
Tamb = –40°C
8.4 mA
8.8 mA
9.2 mA
Tamb = 25°C
9.9 mA
10.3 mA
10.8 mA
Tamb = 85°C
10.9 mA
11.3 mA
11.8 mA
Blocking, Selectivity
As can be seen in Figure 3-3 and Figure 3-4 on page 15, the receiver can receive signals 3 dB
higher than the sensitivity level in the presence of very large blockers of –47 dBm/–34 dBm with
small frequency offsets of ±1/ ±10 MHz.
Figure 3-3 shows narrow band blocking and Figure 3-4 wide band blocking characteristics. The
measurements were done with a signal of 433.92 MHz/FSK/20 Kbit/s/±16 kHz/ Manchester, and
with a level of –106 dBm + 3 dB = –103 dBm which is 3 dB above the sensitivity level. The figures show how much larger than –103dBm a continuous wave signal can be before the BER is
higher than 10–3. The measurements were done at the 50Ω input according to Figure 3-1 on
page 11. At 1 MHz, for example, the blocker can be 56 dB higher than –103 dBm which is
-103 dBm + 56 dB = –47 dBm. These values, together with the good intermodulation performance, avoid the need for a SAW filter in the remote control unit application.
14
ATA5423/ATA5425/ATA5428/ATA5429
4841D–WIRE–10/07
ATA5423/ATA5425/ATA5428/ATA5429
Figure 3-3.
Narrow Band 3 dB Blocking Characteristic at 433.92 MHz
70
Blocking Level (dBC)
60
50
40
30
20
10
0
-10
-5
-4
-3
-2
-1
0
1
2
3
4
5
Distance of Interfering to Receiving Signal (MHz)
Figure 3-4.
Wide Band 3 dB Blocking Characteristic at 433.92 MHz
80
Blocking Level (dBC)
70
60
50
40
30
20
10
0
-10
-50
-40
-30
-20
-10
0
10
20
30
40
50
Distance of Interfering to Receiving Signal (MHz)
Figure 3-5 on page 16 shows the blocking measurement close to the received frequency to illustrate the selectivity and image rejection. This measurement was done 6 dB above the sensitivity
level with a useful signal of 433.92 MHz/FSK/20 Kbit/s/±16 kHz/ Manchester with a level of
–106 dBm + 6 dB = –100 dBm. The figure shows to which extent a continuous wave signal can
surpass –100 dBm until the BER is higher than 10-3. For example, at 1 MHz the blocker can then
be 59 dB higher than –100 dBm which is –100 dBm + 59 dB = –41 dBm.
Table 3-6 on page 16 shows the blocking performance measured relative to –100 dBm for some
other frequencies. Note that sometimes the blocking is measured relative to the sensitivity level
(dBS) instead of the carrier (dBC).
15
4841D–WIRE–10/07
Blocking 6 dB Above Sensitivity Level with BER < 10–3
Table 3-6.
Frequency Offset
Blocker Level
Blocking
+0.75 MHz
–45 dBm
55 dBC/61 dBS
–0.75 MHz
–45 dBm
55 dBC/61 dBS
+1.5 MHz
–38 dBm
62 dBC/68 dBS
–1.5 MHz
–38 dBm
62 dBC/68 dBS
+10 MHz
–30 dBm
70 dBC/76 dBS
–10 MHz
–30 dBm
70 dBC/76 dBS
The ATA5423/ATA5425/ATA5428/ATA5429 can also receive FSK and ASK modulated signals if
they are much higher than the I1dBCP. It can typically receive useful signals at 10 dBm. This is
often referred to as the nonlinear dynamic range which is the maximum to minimum receiving
signal and is 116 dB for 20 Kbit/s Manchester. This value is useful if two transceivers have to
communicate and are very close to each other.
Figure 3-5.
Close In 6 dB Blocking Characteristic and Image Response at 433.92 MHz
70
Blocking Level (dBC)
60
50
40
30
20
10
0
-10
-1.0
-0.8
-0.6
-0.4
-0.2
0
0.2
0.4
0.6
0.8
1.0
Distance of Interfering to Receiving Signal (MHz)
This high blocking performance even makes it possible for some applications using quarter
wave whip antennas to use a simple LC band-pass filter instead of a SAW filter in the receiver.
When designing such an LC filter take into account that the 3 dB blocking at
433.92 MHz/2 = 216.96 MHz is 43 dBC and at 433.92 MHz/3 = 144.64 MHz is 48 dBC and at
2 × (433.92 MHz + 226 kHz) + –226 kHz = 868.066 MHz/868.518 MHz is 56 dBC. And especially that at 3 × (433.92 MHz + 226 kHz) + 226 kHz = 1302.664 MHz the receiver has its
second LO harmonic receiving frequency with only 12 dBC blocking.
16
ATA5423/ATA5425/ATA5428/ATA5429
4841D–WIRE–10/07
ATA5423/ATA5425/ATA5428/ATA5429
3.7
In-band Disturbers, Data Filter, Quasi-peak Detector, Data Slicer
If a disturbing signal falls into the received band or a blocker is not continuous wave, the performance of a receiver strongly depends on the circuits after the IF filter. The demodulator, data
filter and data slicer are important, in that case.
The data filter of the ATA5423/ATA5425/ATA5428/ATA5429 implies a quasi-peak detector. This
results in a good suppression of the above mentioned disturbers and exhibits a good carrier to
Gaussian noise performance. The required useful signal to disturbing signal ratio to be received
with a BER of 10 –3 is less than 12 dB in ASK mode and less than 3 dB (BR_Range_0 to
BR_Range_2)/6 dB (BR_Range_3) in FSK mode. Due to the many different waveforms possible
these numbers are measured for signal as well as for disturbers with peak amplitude values.
Note that these values are worst case values and are valid for any type of modulation and modulating frequency of the disturbing signal as well as the receiving signal. For many combinations,
lower carrier to disturbing signal ratios are needed.
3.8
DEM_OUT Output
The internal raw output signal of the demodulator Demod_Out is available at pin DEM_OUT.
DEM_OUT is an open drain output and must be connected to a pull-up resistor if it is used (typically 100 kΩ) otherwise no signal is present at that pin.
3.9
RSSI Output
The output voltage of the pin RSSI is an analog voltage, proportional to the input power level.
Using the RSSI output signal, the signal strength of different transmitters can be distinguished.
The usable dynamic range of the RSSI amplifier is 70 dB, the input power range P(RFIN) is
–115 dBm to –45 dBm and the gain is 8 mV/dB. Figure 3-6 shows the RSSI characteristic of a
typical device at 433.92 MHz with VS1 = VS2 = 2.4 to 3.6 V and Tamb = –40°C to +85°C with a
matched input according to Table 3-2 on page 12 and Figure 3-1 on page 11. At 915 MHz about
3.3 dB and at 868.3 MHz about 2.7 dB more signal level, at 345 MHz about 0.8 dB and at
315 MHz about 1 dB less signal level is needed for the same RSSI results.
Figure 3-6.
Typical RSSI Characteristic versus Temperature and Supply Voltage
1100
VRSSI (mV)
1000
900
800
max.
700
typ.
min.
600
500
400
-120
-110
-100
-90
-80
-70
-60
-50
-40
PRF_IN (dBm)
17
4841D–WIRE–10/07
3.10
Frequency Synthesizer
The synthesizer is a fully integrated fractional-N design with internal loop filters for receive and
transmit mode. The XTO frequency fXTO is the reference frequency FREF for the synthesizer.
The bits FR0 to FR12 in control registers 2 and 3 (see Table 7-7 on page 39 and Table 7-10 on
page 40) are used to adjust the deviation of fXTO. In transmit mode, at 433.92 MHz, the carrier
has a phase noise of –111 dBC/Hz at 1 MHz and spurious emissions at FREF of –66 dBC with a
high PLL loop bandwidth allowing the direct modulation of the carrier with 20 Kbit/s Manchester
data. Due to the closed loop modulation any spurious emissions caused by this modulation are
effectively filtered out as can be seen in Figure 3-9 on page 20. In RX mode the synthesizer has
a phase noise of –120 dBC/Hz at 1 MHz and spurious emissions of –75 dBC.
The initial tolerances of the crystal oscillator due to crystal tolerances, internal capacitor tolerances and the parasitics of the board have to be compensated at manufacturing setup with
control registers 2 and 3 as can be seen in Table 4-1 on page 28. The other control words for the
synthesizer needed for ASK, FSK and receive/transmit switching are calculated internally. The
RF (Radio Frequency) resolution is equal to the XTO frequency divided by 16384 which is
777.1 Hz at 315.0 MHz, 851.1 Hz at 345.0 MHz, 808.9 Hz at 433.92 MHz, 818.6 Hz at
868.3 MHz and 862.6 Hz at 915.0 MHz.
For the multi-channel system the frequency control word FREQ in control registers 2 and 3 can
be programmed in the range of 1000 to 6900, this is equivalent to a programmable tuning range
of ±2.5 MHz hence every frequency within the 315 MHz, 345 MHz, 433 MHz, 868 MHz and
915 MHz ISM bands can be programmed as receive and as transmit frequency, and the position
of channels within these ISM bands can be chosen arbitrarily (see Table 4-1).
Care must be taken as to the harmonics of the CLK output signal as well as to the harmonics
produced by a microprocessor clocked with it, since these harmonics can disturb the reception
of signals. In a single-channel system, using FREQ = 3803 to 4053 ensures that harmonics of
this signal do not disturb the receive mode.
3.11
FSK/ASK Transmission
Due to the fast modulation capability of the synthesizer and the high resolution, the carrier can
be internally FSK modulated, which simplifies the application of the transceiver. The deviation of
the transmitted signal is ±20 digital frequency steps of the synthesizer which is equal to
±15.54 kHz for 315 MHz, ±17.02 kHz for 345 MHz, ±16.17 kHz for 433.92 MHz, ±16.37 kHz for
868.3 MHz and ±17.25 kHz for 915 MHz.
Due to closed loop modulation with PLL filtering the modulated spectrum is very clean, meeting
ETSI and CEPT regulations when using a simple LC filter for the power amplifier harmonics as it
is shown in Figure 2.2 on page 8. In ASK mode the frequency is internally connected to the center of the FSK transmission and the power amplifier is switched on and off to perform the
modulation. Figure 3-7 on page 19 to Figure 3-9 on page 20 show the spectrum of the FSK modulation with pseudo-random data with 20 Kbit/s/±16.17 kHz/Manchester and 5 dBm output
power.
18
ATA5423/ATA5425/ATA5428/ATA5429
4841D–WIRE–10/07
ATA5423/ATA5425/ATA5428/ATA5429
Figure 3-7.
FSK-modulated TX Spectrum (433.92MHz/20 Kbit/s/±16.17 kHz/Manchester Code)
Ref 10 dB
Samp
Log
10
dB/
Atten 20 dB
VAvg
50
W1 S2
S3 FC
Center 433.92 MHz
Res BW 100 kHz
Figure 3-8.
VBW 100 kHz
Span 30 MHz
Sweep 7.5 ms (401 pts)
Unmodulated TX Spectrum 433.92 MHz – 16.17 kHz (fFSK_L)
Atten 20 dB
Ref 10 dB
Samp
Log
10
dB/
VAvg
50
W1 S2
S3 FC
Center 433.92 MHz
Res BW 10 kHz
VBW 10 kHz
Span 1 MHz
Sweep 27.5 ms (401 pts)
19
4841D–WIRE–10/07
Figure 3-9.
FSK-modulated TX Spectrum (433.92 MHz/20 Kbit/s/±16.17 kHz/Manchester Code)
Atten 20 dB
Ref 10 dB
Samp
Log
10
dB/
VAvg
50
W1 S2
S3 FC
Center 433.92 MHz
Res BW 10 kHz
3.12
VBW 10 kHz
Span 1 MHz
Sweep 27.5 ms (401 pts)
Output Power Setting and PA Matching at RF_OUT
The Power Amplifier (PA) is a single-ended open collector stage which delivers a current pulse
which is nearly independent of supply voltage, temperature and tolerances due to band gap stabilization. Resistor R1, see Figure 3-10 on page 21, sets a reference current which controls the
current in the PA. A higher resistor value results in a lower reference current, a lower output
power and a lower current consumption of the PA. The usable range of R1 is 15 kΩ to 56 kΩ. Pin
PWR_H switches the output power range between about 0 dBm to 5 dBm (PWR_H = GND) and
5 dBm to 10 dBm (PWR_H = AVCC) by multiplying this reference current by a factor 1
(PWR_H = GND) and 2.5 (PWR_H = AVCC), which corresponds to about 5 dB more output
power.
If the PA is switched off in TX mode, the current consumption without output stage with
VS1 = VS2 = 3 V, Tamb = 25°C is typically 6.5 mA for 868.3 MHz and 6.95 mA for 315 MHz and
433.92 MHz.
The maximum output power is achieved with optimum load resistances RLopt according to Table
3-7 on page 22 with compensation of the 1.0 pF output capacitance of the RF_OUT pin by
absorbing it into the matching network consisting of L1, C1, C3 as shown in Figure 3-10 on page
21. There must also be a low resistive DC path to AVCC to deliver the DC current of the power
amplifier's last stage. The matching of the PA output was done with the circuit shown in Figure
3-10 on page 21 with the values in Table 3-7 on page 22. Note that value changes of these elements may be necessary to compensate for individual board layouts.
20
ATA5423/ATA5425/ATA5428/ATA5429
4841D–WIRE–10/07
ATA5423/ATA5425/ATA5428/ATA5429
Example:
According to Table 3-7 on page 22, with a frequency of 433.92 MHz and output power of
11 dBm the overall current consumption is typically 17.8 mA; hence, the PA needs
17.8 mA - 6.95 mA = 10.85 mA in this mode, which corresponds to an overall power amplifier
efficiency of the PA of (10(11dBm/10) × 1 mW)/(3 V × 10.85 mA) × 100% = 38.6% in this case.
Using a higher resistor in this example of R1 = 1.091 × 22 kΩ = 24 kΩ results in 9.1% less current in the PA of 10.85 mA/1.091 = 9.95 mA and 10 × log(1.091) = 0.38 dB less output power if
using a new load resistance of 300Ω × 1.091 = 327Ω. The resulting output power is then
11 dBm – 0.38 dB = 10.6 dBm and the overall current consumption is
6.95 mA + 9.95 mA = 16.9 mA.
The values of Table 3-7 on page 22 were measured with standard multi-layer chip inductors with
quality factors Q according to Table 3-7 on page 22. Looking to the 433.92 MHz/11 dBm case
with the quality factor of QL1 = 43 the loss in this inductor is estimated with the parallel equivalent
r e s i s ta n c e o f t h e i n d u c to r R l o s s = 2 × π × f × L × Q L 1 a n d t h e m a tc h i n g l o s s w i t h
10 log (1 + RLopt/Rloss) which is equal to 0.32 dB losses in this inductor. Taking this into account,
the PA efficiency is then 42% instead of 38.6%.
Be aware that the high power mode (PWR_H = AVCC) can only be used with a supply voltage
higher than 2.7V, whereas the low power mode (PWR_H = GND) can be used down to 2.4V as
can be seen in the “Electrical Characteristics: General” on page 67.
The supply blocking capacitor C 2 (10 nF) has to be placed close to the matching network
because of the RF current flowing through it.
Figure 3-10. Power Setting and Output Matching
AVCC
C2
L1
RFOUT
C1
10
ATA5423/ATA5425/
ATA5428/ATA5429
RF_OUT
8
C3
R_PWR
R1
9
VPWR_H
PWR_H
21
4841D–WIRE–10/07
Table 3-7.
Measured Output Power and Current Consumption with VS1 = VS2 = 3V, Tamb = 25°C
Frequency (MHz) TX Current (mA) Output Power (dBm)
3.13
R1 (kΩ)
VPWR_H
RLopt (Ω)
L1 (nH)
QL1
C1 (pF) C3 (pF)
315
8.5
0.4
56
GND
2500
82
28
1.5
0
315
10.5
5.7
27
GND
920
68
32
2.2
0
315
16.7
10.5
27
AVCC
350
56
35
3.9
0
345
8.8
1.6
56
GND
2400
82
75
1.2
0
345
10.4
5.9
27
GND
900
68
74
1.8
0
345
16.9
10.7
27
AVCC
320
43
65
3.9
0
433.92
8.6
0.1
56
GND
2300
56
40
0.75
0
433.92
11.2
6.2
22
GND
890
47
38
1.5
0
433.92
17.8
11
22
AVCC
300
33
43
2.7
0
868.3
9.3
-0.3
33
GND
1170
12
58
1.0
3.3
868.3
11.5
5.4
15
GND
471
15
54
1.0
0
868.3
16.3
9.5
22
AVCC
245
10
57
1.5
0
915
9.6
0.1
33
GND
1100
12
62
0.7
0
915
11.8
4.9
15
GND
465
12
62
1.5
0
915
20.3
10.2
15
AVCC
230
10
60
1.5
0
Output Power and TX Supply Current versus Supply Voltage and Temperature
Table 3-8 on page 22 shows the measurement of the output power for a typical device with
VS = VS1 = VS2 in the 433.92 MHz and 6.2 dBm case versus temperature and supply voltage
measured according to Figure 3-10 on page 21 with components according to Table 3-7. As
opposed to the receiver sensitivity, the supply voltage has here the major impact on output
power variations because of the large signal behavior of a power amplifier. Thus, a two battery
system with voltage regulator or a 5V system shows much less variation than a 2.4V to 3.6V one
battery system because the supply voltage is then well within 3.0V and 3.6V.
The reason is that the amplitude at the output RF_OUT with optimum load resistance is
AVCC – 0.4V and the power is proportional to (AVCC – 0.4V) 2 if the load impedance is not
changed. This means that the theoretical output power reduction if reducing the supply voltage
from 3.0V to 2.4V is 10 log ((3 V – 0.4 V)2/(2.4 V – 0.4 V)2) = 2.2 dB. Table 3-8 shows that principle behavior in the measurement. This is not the same case for higher voltages, since here
increasing the supply voltage from 3V to 3.6V should theoretical increase the power by 1.8 dB;
but a gain of only 0.8 dB in the measurement shows that the amplitude does not increase with
the supply voltage because the load impedance is optimized for 3V and the output amplitude
stays more constant.
Table 3-8.
22
Measured Output Power and Supply Current at 433.92 MHz, PWR_H = GND
VS =
2.4 V
3.0 V
3.6 V
Tamb = –40°C
10.19 mA
3.8 dBm
10.19 mA
5.5 dBm
10.78 mA
6.2 dBm
Tamb = +25°C
10.62 mA
4.6 dBm
11.19 mA
6.2 dBm
11.79 mA
7.1 dBm
Tamb = +85°C
11.4 mA
3.9 dBm
12.02 mA
5.5 dBm
12.73 mA
6.6 dBm
ATA5423/ATA5425/ATA5428/ATA5429
4841D–WIRE–10/07
ATA5423/ATA5425/ATA5428/ATA5429
Table 3-9 shows the relative changes of the output power of a typical device compared to
3.0V/25°C. As can be seen, a temperature change to –40°C as well as to +85°C reduces the
power by less than 1 dB due to the band gap regulated output current. Measurements of all the
cases in Table 3-7 on page 22 over temperature and supply voltage have shown about the same
relative behavior as shown in Table 3-9.
Table 3-9.
3.14
Measurements of Typical Output Power Relative to 3V/25°C
VS =
2.4V
3.0V
3.6V
Tamb = –40°C
–2.4 dB
–0.7 dB
0 dB
Tamb = +25°C
–1.6 dB
0 dB
+0.9 dB
Tamb = +85°C
–2.3 dB
–0.7 dB
+0.4 dB
RX/TX Switch
The RX/TX switch decouples the LNA from the PA in TX mode, and directs the received power
to the LNA in RX mode. To do this, it has a low impedance to GND in TX mode and a high
impedance to GND in RX mode. To design a proper RX/TX decoupling, a linear simulation tool
for radio frequency design together with the measured device impedances of Table 3-1 on page
11, Table 3-7 on page 22, Table 3-10 and Table 3-11 on page 24 should be used, but the exact
element values have to be found on-board. Figure 3-11 shows an approximate equivalent circuit
of the switch. The principal switching operation is described here according to the application of
Figure 2-1 on page 7. The application of Figure 2.2 on page 8 works similarly.
Table 3-10.
Impedance of the RX/TX Switch RX_TX2 Shorted to GND
Frequency
Z(RX_TX1) TX Mode
Z(RX_TX1) RX Mode
315 MHz
(4.8 + j3.2)Ω
(11.3 – j214)Ω
345 MHz
(4.7 + j3.4)Ω
(11.1 – j181)Ω
433.92 MHz
(4.5 + j4.3)Ω
(10.3 – j153)Ω
868.3 MHz
(5 + j9)Ω
(8.9 – j73)Ω
915 MHz
(5 + j9.2)Ω
(9 – j65)Ω
Figure 3-11. Equivalent Circuit of the Switch
RX_TX1
1.6 nH
2.5 pF
11Ω
TX
5Ω
23
4841D–WIRE–10/07
3.15
Matching Network in TX Mode
In TX mode the 20 mm long and 0.4 mm wide transmission line which is much shorter than λ/4 is
approximately switched in parallel to the capacitor C9 to GND. The antenna connection between
C8 and C 9 has an impedance of about 50Ω locking from the transmission line into the loop
antenna with pin RF_OUT, L2, C10, C8 and C9 connected (using a C9 without the added 7.6 pF
as discussed later). The transmission line can be approximated with a 16 nH inductor in series
with a 1.5Ω resistor, the closed switch can be approximated according to Table 3-10 on page 23
with the series connection of 1.6 nH and 5Ω in this mode. To have a parallel resonant high
impedance circuit with little RF power going into it looking from the loop antenna into the transmission line a capacitor of about 7.6 pF to GND is needed at the beginning of the transmission
line (this capacitor is later absorbed into C9 which is then higher, as needed for 50Ω transformation). To keep the 50Ω impedance in RX mode at the end of this transmission line, C7 also has to
be about 7.6 pF. This reduces the TX power by about 0.5 dB at 433.92 MHz compared to the
case the where the LNA path is completely disconnected.
3.16
Matching Network in RX Mode
In RX mode the RF_OUT pin has a high impedance of about 7 kΩ in parallel with 1.0 pF at
433.92 MHz as can be seen in Table 3-11. This, together with the losses of the inductor L2 with
120 nH and QL2 = 25, gives about 3.7 kΩ loss impedance at RF_OUT. Since the optimum load
impedance in TX mode for the power amplifier at RF_OUT is 890 Ω the loss associated with the
inductor L2 and the RF_OUT pin can be estimated to be 10 × log(1 + 890/3700) = 0.95 dB compared to the optimum matched loop antenna without L2 and RF_OUT. The switch represents, in
this mode at 433.92 MHz, approximately an inductor of 1.6 nH in series with the parallel connection of 2.5 pF and 2.0 kΩ. Since the impedance level at pin RX_TX1 in RX mode is about 50Ω
this only negligibly dampens the received signal (by about 0.1 dB). When matching the LNA to
the loop antenna, the transmission line and the 7.6 pF part of C9 have to be taken into account
when choosing the values of C11 and L1 so that the impedance seen from the loop antenna into
the transmission line with the 7.6 pF capacitor connected is 50Ω. Since the loop antenna in RX
mode is loaded by the LNA input impedance, the loaded Q of the loop antenna is lowered by
about a factor of 2 in RX mode; hence the antenna bandwidth is higher than in TX mode.
Table 3-11.
Impedance RF_OUT Pin in RX Mode
Frequency
Z(RF_OUT)RX
RP//CP
315 MHz
36Ω – j 502Ω
7 kΩ//1.0 pF
345 MHz
33Ω – j 480Ω
7 kΩ//1.0 pF
433.92 MHz
19Ω – j 366Ω
7 kΩ//1.0 pF
868.3 MHz
2.8Ω – j 141Ω
7 kΩ//1.3 pF
915 MHz
2.6Ω – j 135Ω
7 kΩ//1.3 pF
Note that if matching to 50Ω, like in Figure 2.2 on page 8, a high Q wire-wound inductor with a
Q > 70 should be used for L2 to minimize its contribution to RX losses that will otherwise be
dominant. The RX and TX losses will be in the range of 1.0 dB there.
24
ATA5423/ATA5425/ATA5428/ATA5429
4841D–WIRE–10/07
ATA5423/ATA5425/ATA5428/ATA5429
4. XTO
The XTO is an amplitude-regulated Pierce oscillator type with integrated load capacitances
(2 × 18 pF with a tolerance of ±17%) hence CLmin = 7.4 pF and CLmax = 10.6 pF. The XTO oscillation frequency fXTO is the reference frequency FREF for the fractional-N synthesizer. When
designing the system in terms of receiving and transmitting frequency offset, the accuracy of the
crystal and XTO have to be considered.
The synthesizer can adjust the local oscillator frequency for the initial frequency error in fXTO.
This is done at nominal supply voltage and temperature with the control registers 2 and 3 (see
Table 7-7 and Table 7-10). The remaining local oscillator tolerance at nominal supply voltage
and temperature is then < ±0.5 ppm. The XTO’s gm has very low influence of less than ±2 ppm
on the frequency at nominal supply voltage and temperature.
In a single channel system less than ±150 ppm should be corrected to avoid that harmonics of
the CLK output disturb the receive mode. If the CLK is not used or if it is carefully laid out on the
application PCB (as needed for multi channel systems), more than ±150 ppm can be
compensated.
Over temperature and supply voltage, the XTO's additional pulling is only ±2 ppm. The XTAL
versus temperature and its aging is then the main source of frequency error in the local
oscillator.
The XTO frequency depends on XTAL properties and the load capacitances CL1, 2 at pin XTAL1
and XTAL2. The pulling of fXTO from the nominal fXTAL is calculated using the following formula:
C LN – C L
Cm
6
P = -------- × ------------------------------------------------------------- × 10 ppm.
2
( C 0 + C LN ) × ( C 0 + C L )
Cm is the crystal's motional, C0 the shunt and CLN the nominal load capacitance of the XTAL
found in its data sheet. CL is the total actual load capacitance of the crystal in the circuit and consists of CL1 and CL2 in series connection.
Figure 4-1.
XTAL with Load Capacitance
Crystal equivalent circuit
C0
XTAL
Lm
CL1
CL2
Cm
Rm
CL = CL1 × CL2/ (CL1 + CL2)
With C m ≤14 fF, C0 ≥ 1.5 pF, C LN = 9 pF and C L = 7.4 pF to 10.6 pF, the pulling amounts to
P ≤±100 ppm and with Cm ≤7 fF, C0 ≥ 1.5 pF, CLN = 9 pF and CL = 7.4 pF to 10.6 pF, the pulling
is P ≤ ±50 ppm.
Since typical crystals have less than ±50 ppm tolerance at 25°C, the compensation is not critical, and can in both cases be done with the ±150 ppm.
25
4841D–WIRE–10/07
C0 of the XTAL has to be lower than CLmin/2 = 3.7 pF for a Pierce oscillator type in order to not
enter the steep region of pulling versus load capacitance where there is a risk of an unstable
oscillation.
To ensure proper start-up behavior the small signal gain, and thus the negative resistance, provided by this XTO at start is very large; for example, oscillation starts up even in worst case with
a crystal series resistance of 1.5 kΩ at C 0 ≤2.2 pF with this XTO. The negative resistance is
approximately given by
⎧ Z1 × Z3 + Z2 × Z3 + Z1 × Z2 × Z3 × gm ⎫
Re {Z XTOcore } = Re ⎨ ------------------------------------------------------------------------------------------------------ ⎬
Z1 + Z2 + Z3 + Z1 × Z2 × gm
⎩
⎭
with Z1, Z2 as complex impedances at pin XTAL1 and XTAL2, hence
Z1 = –j/(2 × π × fXTO × CL1) + 5Ω and Z2 = –j/(2 × π × fXTO × CL2) + 5Ω.
Z3 consists of crystals C0 in parallel with an internal 110 kΩ resistor hence
Z3 = –j/(2 × π × fXTO × C0) /110 kΩ, gm is the internal transconductance between XTAL1 and
XTAL2 with typically 19 mS at 25°C.
With fXTO = 13.5 MHz, gm = 19 mS, CL = 9 pF, and C0 = 2.2 pF, this results in a negative resistance of about 2 kΩ. The worst case for technological, temperature and supply voltage variations
is then for C0 ≤2.2 pF always higher than 1.5 kΩ.
Due to the large gain at startup, the XTO is able to meet a very low start-up time. The oscillation
start-up time can be estimated with the time constant τ .
2
τ = ----------------------------------------------------------------------------------------------------------2
2
4 × π × f m × C m × ( Re ( Z XTOcore ) + R m )
After 10 τ to 20 τ an amplitude detector detects the oscillation amplitude and sets XTO_OK to
High if the amplitude is large enough. This sets N_RESET to High and activates the CLK output
if CLK_ON in control register 3 is High (see Table 7-7). Note that the necessary conditions of the
VSOUT and DVCC voltage also have to be fulfilled (see Figure 4-2 and Figure 5-1).
To save current in IDLE and Sleep modes, the load capacitors are partially switched off in these
modes with S1 and S2, as seen in Figure 4-2.
It is recommended to use a crystal with C m = 3.0 fF to 7.0 fF, C LN = 9 pF, R m < 120Ω and
C0 = 1.0 pF to 2.2 pF.
Lower values of Cm can be used, this increases the start-up time slightly. Lower values of C0 or
higher values of Cm (up to 15 fF) can also be used, this has only little influence on pulling.
26
ATA5423/ATA5425/ATA5428/ATA5429
4841D–WIRE–10/07
ATA5423/ATA5425/ATA5428/ATA5429
Figure 4-2.
XTO Block Diagram
XTAL1
XTAL2
CLK
&
fXTO
8 pF
10 pF
10 pF
CL1
S1
DVCC_OK
(from power supply)
Divider
/3
CLK_ON
(control
register 3)
8 pF
VSOUT_OK
(from power supply)
Amplitude
detector
CL2
XTO_OK
(to reset logic)
S2
Divider
/16
fDCLK
Divider
/1
/2
/4
/8
/16
fXDCLK
In IDLE mode and during Sleep mode (RX_Polling)
the switches S1 and S2 are open.
Baud1
Baud0
XLim
To find the right values used in control registers 2 and 3 (see Table 7-7 and Table 7-10), the
relationship between fXTO and the fRF is shown in Table 4-1 on page 28. To determine the right
content, the frequency at pin CLK as well as the output frequency at RF_OUT in ASK mode can
be measured, then the FREQ value can be calculated according to Table 4-1 on page 28 so that
fRF is exactly the desired radio frequency.
27
4841D–WIRE–10/07
Table 4-1.
Calculation of fRF
Frequency
(MHz)
Pin 6
433_N868
CREG1
Bit(4)
FS
fXTO (MHz)
fRF = fTX_ASK = fRX
fTX_FSK_L
fTX_FSK_H
315
AVCC
1
12.73193
+ 20.5-⎞
f XTO × ⎛ 24.5 + FREQ
--------------------------------⎝
16384 ⎠
fRF –15.54 kHz
fRF +
15.54 kHz
777.1 Hz
345
AVCC
0
13.94447
+ 20.5-⎞
f XTO × ⎛ 24.5 + FREQ
--------------------------------⎝
16384 ⎠
fRF –17.02 kHz
fRF +
17.02 kHz
851.1 Hz
433.92
AVCC
0
13.25311
FREQ + 20.5
f XTO × ⎛⎝ 32.5 + ----------------------------------⎞⎠
16384
fRF –16.17 kHz
fRF +
16.17 kHz
808.9 Hz
868.3
GND
0
13.41191
+ 20.5-⎞
f XTO × ⎛ 64.5 + FREQ
--------------------------------⎝
16384 ⎠
fRF –16.37 kHz
fRF +
16.37 kHz
818.6 Hz
915
GND
0
14.13324
+ 20.5-⎞
f XTO × ⎛ 64.5 + FREQ
--------------------------------⎝
16384 ⎠
fRF –17.25 kHz
fRF +
17.25 kHz
862.6 Hz
Frequency
Resolution
The variable FREQ depends on FREQ2 and FREQ3, which are defined by the bits FR0 to FR12
in control register 2 and 3, and is calculated as follows:
FREQ = FREQ2 + FREQ3
Care must be taken to the harmonics of the CLK output signal fCLK as well as to the harmonics
produced by an microprocessor clocked with it, since these harmonics can disturb the reception
of signals if they get to the RF input. In a single channel system, using FREQ = 3803 to 4053
ensures that the harmonics of this signal do not disturb the receive mode. In a multichannel system, the CLK signal can either be not used or carefully laid out on the application PCB. The
supply voltage of the microcontroller must also be carefully blocked in a multichannel system.
28
ATA5423/ATA5425/ATA5428/ATA5429
4841D–WIRE–10/07
ATA5423/ATA5425/ATA5428/ATA5429
4.1
Pin CLK
Pin CLK is an output to clock a connected microcontroller. The clock frequency fCLK is calculated
as follows:
f XTO
f CLK = ---------3
Because the enabling of pin CLK is asynchronous, the first clock cycle may be incomplete. The
signal at CLK output has a nominal 50% duty cycle.
Figure 4-3.
Clock Timing
VThres_2 = 2.38V (typically)
VSOUT
VThres_1 = 2.3V (typically)
CLK
N_RESET
CLK_ON
(Control register 3)
4.2
Basic Clock Cycle of the Digital Circuitry
The complete timing of the digital circuitry is derived from one clock. As shown in Figure 4-2
on page 27, this clock cycle TDCLK is derived from the crystal oscillator (XTO) in combination with
a divider.
f XTO
f DCLK = ---------16
TDCLK controls the following application relevant parameters:
• Timing of the polling circuit including bit check
• TX bit rate
The clock cycle of the bit check and the TX bit rate depends on the selected bit-rate range
(BR_Range) which is defined in control register 6 (see Table 7-20 on page 42) and XLim which
is defined in control register 4 (see Table 7-13 on page 40). This clock cycle TXDCLK is defined by
the following formulas for further reference:
BR_Range ⇒
BR_Range 0: TXDCLK = 8 ×
BR_Range 1: TXDCLK = 4 ×
BR_Range 2: TXDCLK = 2 ×
BR_Range 3: TXDCLK = 1 ×
TDCLK ×
TDCLK ×
TDCLK ×
TDCLK ×
XLim
XLim
XLim
XLim
29
4841D–WIRE–10/07
5. Power Supply
Figure 5-1.
Power Supply
VS1
SW_AVCC
IN
VS2
V_REG1
3.25V typ.
VSINT
OUT
AVCC
EN
(Control register 1)
≥1
AVCC_EN
FF1
PWR_ON
T1
S Q
to
T5
R
SW_VSOUT
DVCC_OK
OFFCMD
S
0
0
1
1
(Command via SPI)
VS1+
0.55V
typ.
VAUX
DVCC
≥1
+
IN
VSOUT_EN
R
0
1
0
1
Q
no change
0
1
1
P_On_Aux
SW_DVCC
V_Monitor
(1.5V typ.)
and
(Status register)
V_REG2
3.25V typ.
OUT
V_Monitor
(2.3V/
2.38V typ.)
DVCC_OK
(to XTO and
Reset Logic)
VSOUT_OK
(to XTO and
Reset Logic)
Low_Batt
(Status Register
and Reset Logic)
VSOUT
EN
(Control register 3)
The supply voltage range of the ATA5423/ATA5425/ATA5428/ATA5429 is 2.4V to 3.6V or 4.4V
to 6.6V.
Pin VS1 is the supply voltage input for the range 2.4V to 3.6V and is used in 1 Li battery applications (3V) using a single lithium 3V cell. Pin VS2 is the voltage input for the range 4.4V to 6.6V
(2 Li battery application (6V) and Base-station Application (5V); in this case, the voltage regulator V_REG1 regulates VS1 to typically 3.25V. If the voltage regulator is active, a blocking
capacitor of 2.2 µF has to be connected to VS1.
Pin VAUX is an input for an additional auxiliary voltage supply and can be connected, for example, to an inductive supply (see Figure 5-6 on page 36). This input can only be used together
with a rectifier or as in the application shown in Figure 2.2 on page 8 and must otherwise be left
open.
Pin VSINT is the voltage input for the Microcontoller_Interface and must be connected to the
power supply of the microcontroller. The voltage range of VVSINT is 2.4V to 5.25V (see Figure 5-5
on page 35 and Figure 5-6 on page 36).
30
ATA5423/ATA5425/ATA5428/ATA5429
4841D–WIRE–10/07
ATA5423/ATA5425/ATA5428/ATA5429
AVCC is the internal operation voltage of the RF transceiver and is fed by VS1 via the switch
SW_AVCC. AVCC must be blocked with a 68 nF capacitor (see Figure 2-1 on page 7, Figure 2.2
on page 8 and Figure 2-3 on page 9).
DVCC is the internal operation voltage of the digital control logic and is fed by VS1 or VSOUT
via the switch SW_DVCC. DVCC must be blocked on pin DVCC with 68 nF (see Figure 2-1 on
page 7, Figure 2.2 on page 8 and Figure 2-3 on page 9).
Pin VSOUT is a power supply output voltage for external devices (for example, microcontrollers)
and is fed by VS1 via the switch SW_VSOUT, or by the auxiliary voltage supply VAUX via
V_REG2. The voltage regulator V_REG2 regulates VSOUT to typically 3.25V. If the voltage regulator is active, a blocking capacitor of 2.2 µF has to be connected to VSOUT. VSOUT can be
switched off by the VSOUT_EN bit in control register 3 and is then reactivated by conditions
found in Figure 5-2 on page 32.
Pin N_RESET is set to low if the voltage VVSOUT at pin VSOUT drops below 2.3V (typically) and
can be used as a reset signal for a connected microcontroller (see Figure 5-3 on page 34 and
Figure 5-4 on page 35).
Pin PWR_ON is an input to switch on the transceiver (active high).
Pin T1 to T5 are inputs for push buttons and can also be used to switch on the transceiver
(active low).
For current consumption reasons it is recommended to set T1 to T5 to GND, or PWR_ON to
VCC only temporarily. Otherwise, an additional current flows because of a 50 kΩ pull-up resistor.
There are two voltage monitors generating the following signals (see Figure 5-1 on page 30):
• DVCC_OK if DVCC > 1.5V typically
• VSOUT_OK if VSOUT > VThres1 (2.3V typically)
• Low_Batt if VSOUT < VThres2 (2.38V typically)
31
4841D–WIRE–10/07
Figure 5-2.
Operation Modes Flow Chart
Bit AVCC_EN = 0 and OFF Command and
Pin PWR_ON = 0 and
Pin T1, T2, T3, T4 and T5 = 1
OFF Mode
VVAUX > 3.5V (typ)
Pin PWR_ON = 1 or
Pin T1, T2, T3, T4 or
Pin T5
AVCC = VS1
DVCC = VS1
VSOUT = VS1
VVAUX < VS1 + 0.5V
AVCC = VS1
DVCC = VS1
VSOUT = V_REG2
VVAUX > VS1 + 0.5V
OPM1 OPM0
0
1
TX Mode
1
0
RX Polling Mode
1
1
RX Mode
Pin PWR_ON = 1 or
Pin T1, T2, T3, T4 or
Pin T5 or
Bit AVCC_EN = 1
IDLE Mode
OPM1 = 0 and OPM0 = 0
IDLE Mode
VVAUX < 3.5V (typ)
AVCC = OFF
DVCC = OFF
VSOUT = OFF
Bit AVCC_EN = 0 and
OFF Command and
Pin PWR_ON = 0 and
Pin T1, T2, T3, T4 and
T5 = 1
VSOUT_EN = 0
Statusbit Power_On = 1
or
Event on Pin T1, T2, T3, T4 or T5
AUX Mode
AVCC = OFF
DVCC = V_REG2
VSOUT = V_REG2
IDLE Mode
AVCC = VS1
DVCC = VS1
VSOUT = OFF
OPM1 = 0 and OPM0 = 1
TX Mode
AVCC = VS1
DVCC = VS1
VSOUT = VS1
or V_REG2
OPM1 = 0 and OPM0 = 1 RX Polling Mode
OPM1 = 1 and OPM0 = 0
AVCC = VS1
DVCC = VS1
VSOUT = VS1
or V_REG2
OPM1 = 1 and OPM0 = 0
OPM1 = 1 and OPM0 = 1
or Bit check ok
RX Mode
AVCC = VS1
DVCC = VS1
VSOUT = VS1
or V_REG2
OPM1 = 1 and OPM0 = 1
VSOUT_EN = 0
Status bit Power_On = 1
or
Event on Pin T1, T2, T3, T4 or T5
RX Polling Mode
AVCC = VS1
DVCC = VS1
VSOUT = OFF
5.1
Bit check ok
OFF Mode
If the power supply (battery) is connected to pin VS1 and/or VS2, and if the voltage on pin VAUX
VVAUX < 3.5V (typically), then the transceiver is in OFF mode. In OFF mode AVCC, DVCC and
VSOUT are disabled, resulting in very low power consumption (IS_OFF is typically 10 nA). In OFF
mode the transceiver is not programmable via the 4-wire serial interface.
32
ATA5423/ATA5425/ATA5428/ATA5429
4841D–WIRE–10/07
ATA5423/ATA5425/ATA5428/ATA5429
5.2
AUX Mode
The transceiver changes from OFF mode to AUX mode if the voltage at pin VAUX VVAUX > 3.5V
(typically). In AUX mode DVCC and VSOUT are connected to the auxiliary power supply input
(VAUX) via the voltage regulator V_REG2. In AUX mode the transceiver is programmable via
the 4-wire serial interface, but no RX or TX operations are possible because AVCC = OFF.
The state transition OFF mode to AUX mode is indicated by an interrupt at pin IRQ and the status bit P_On_Aux = 1.
5.3
IDLE Mode
In IDLE mode AVCC and DVCC are connected to the battery voltage (VS1).
From OFF mode the transceiver changes to IDLE mode if pin PWR_ON is set to 1 or pin T1, T2,
T3, T4 or T5 is set to “0”. This state transition is indicated by an interrupt at pin IRQ and the status bits Power_On = 1 or ST1, ST2, ST3, ST4 or ST5 = 1.
From AUX mode the transceiver changes to IDLE mode by setting AVCC_EN = 1 in control
register 1 via the 4-wire serial interface or if pin PWR_ON is set to “1” or pin T1, T2, T3, T4 or T5
is set to “0”.
VSOUT is either connected to VS1 or to the auxiliary power supply (V_REG2).
If VVAUX < VS1 + 0.5V, VSOUT is connected to VS1. If VVAUX > VS1 + 0.5V, VSOUT is connected
to V_REG2 and the status bit P_On_Aux is set to “1”.
In IDLE mode, the RF transceiver is disabled and the power consumption IS_IDLE is about 230 µA
(VSOUT OFF and CLK output OFF and VS = VS1 = VS2 = 3V). The exact value of this current
is strongly dependent on the application and the exact operation mode, therefore check the section “Electrical Characteristics: General” on page 67 for the appropriate application case.
Via the 4-wire serial interface a connected microcontroller can program the required parameter
and enable the TX, RX polling or RX mode.
The transceiver can be set back to OFF mode by an OFF command via the 4-wire serial interface (the bit AVCC_EN must be set to “0”, the input level of pin PWR_ON must be “0” and pin
T1, T2, T3, T4 and T5 = 1 before writing the OFF command).
Table 5-1.
5.4
Control Register 1
OPM1
OPM0
Function
0
0
IDLE mode
Reset Timing and Reset Logic
If the transceiver is switched on (OFF mode to IDLE mode, OFF mode to AUX mode) DVCC and
VSOUT ramp up as illustrated in Figure 5-3 on page 34 (AVCC only ramps up if the transceiver
is set to the IDLE mode). The internal signal DVCC_RESET resets the digital control logic and
sets the control register to default values.
A voltage monitor generates a low level at pin N_RESET until the voltage at pin VSOUT
exceeds 2.38V (typically) and the start-up time of the XTO has elapsed (amplitude detector, see
Figure 4-2 on page 27). After the voltage at pin VSOUT exceeds 2.3V (typically) and the start-up
time of the XTO has elapsed, the output clock at pin CLK is available. Because the enabling of
pin CLK is asynchronous, the first clock cycle may be incomplete.
33
4841D–WIRE–10/07
The status bit Low_Batt is set to “1” if the voltage at pin VSOUT VVSOUT drops below VThres_2
(typically 2.38V). Low_Batt is set to “0” if VVSOUT exceeds VThres_2 and the status register is read
via the 4-wire serial interface or N_RESET is set to low.
If VVSOUT drops below VThres_1 (typically 2.3V), N_RESET is set to low. If bit VSOUT_EN in control register 3 is “1”, a DVCC_RESET is also generated. If VVSOUT was already disabled by the
connected microcontroller by setting bit VSOUT_EN = 0, no DVCC_RESET is generated.
Note:
Figure 5-3.
If VSOUT < VThres_1 (typically 2.3 V) the output of the pin CLK is low, the Microcontroller_Interface
is disabled and the transceiver is not programmable via the 4-wire serial interface.
Reset Timing
VThres_2 = 2.38V (typ)
VThres_1 = 2.3V (typ)
VSOUT
1.5V (typically)
DVCC
(AVCC)
DVCC_RESET
VSOUT > 2.38V and the XTO is running
N_RESET
LOW_Batt
(Status Register)
VSOUT_EN
(Control Register 3)
VSOUT > 2.3V and the XTO is running
VSOUT
34
ATA5423/ATA5425/ATA5428/ATA5429
4841D–WIRE–10/07
ATA5423/ATA5425/ATA5428/ATA5429
Figure 5-4.
Reset Logic, SR Latch Generates the Hysteresis in the NRESET Signal
DVCC_OK
and
≥1
XTO_OK
DVCC_RESET
VSOUT_EN
and
N_RESET
and
S
Q
R
Q
VSOUT_OK
LOW_BATT
5.5
S R
Q
0
0
1
1
no change
0
1
no change
0
1
0
1
1 Li Battery Application (3V)
The supply voltage range is 2.4V to 3.6V and VAUX is not used.
Figure 5-5.
1 Li Battery Application (3V)
ATA5423/ATA5425/
ATA5428/ATA5429 VS1
ATmega
48/88/168
2.4V to 3.6V
VS2
VAUX
RF Transceiver
Digital Control
Logic
AVCC
DVCC
VSOUT
VS
Microcontroller_Interface
VSINT
CS
OUT
SCK
OUT
SDI_TMDI
OUT
SDO_TMDO
IN
IRQ
IN
CLK
IN
NRESET
IN
DEM_OUT
35
4841D–WIRE–10/07
5.6
2 Li Battery Application (6V)
The supply voltage range is 4.4V to 6.6V and VAUX is connected to an inductive supply.
Figure 5-6.
2 Li Battery Application (6V) with Inductive Emergency Supply
ATmega
48/88/168
ATA5423/ATA5425/
ATA5428/ATA5429 VS1
VS2
4.4V to 6.6V
VAUX
RF Transceiver
Digital Control
Logic
AVCC
DVCC
VSOUT
VS
Microcontroller_Interface
VSINT
CS
OUT
SCK
OUT
SDI_TMDI
OUT
SDO_TMDO
IN
IRQ
IN
CLK
IN
NRESET
IN
DEM_OUT
6. Microcontroller Interface
The microcontroller interface is a level converter which converts all internal digital signals that
are referred to the DVCC voltage into the voltage used by the microcontroller. Therefore, the pin
VSINT has to be connected to the supply voltage of the microcontroller.
This makes it possible to use the internal voltage regulator/switch at pin VSOUT as in Figure 2-1
on page 7 and Figure 2-3 on page 9 or to connect the microcontroller and the pin VSINT directly
to the supply voltage of the microcontroller as in Figure 2.2 on page 8.
7. Digital Control Logic
7.1
Register Structure
The configuration of the transceiver is stored in RAM cells. The RAM contains a 16 × 8-bit
TX/RX data buffer and a 6 × 8-bit control register and is writable and readable via a 4-wire serial
interface (CS, SCK, SDI_TMDI, SDO_TMDO).
The 1 × 8-bit status register is not part of the RAM and is readable via the 4-wire serial interface.
The RAM and the status information are stored as long as the transceiver is in any active mode
(DVCC = VS1 or DVCC = V_REG2) and are lost when the transceiver switches to OFF mode
(DVCC =OFF).
36
ATA5423/ATA5425/ATA5428/ATA5429
4841D–WIRE–10/07
ATA5423/ATA5425/ATA5428/ATA5429
After the transceiver is turned on via pin PWR_ON = High, T1 = Low, T2 = Low, T3 = Low,
T4 = Low or T5 = Low or the voltage at pin VAUX VVAUX > 3.5V (typically), the control registers
are in the default state.
Figure 7-1.
Register Structure
MSB
LSB
TX/RX Data Buffer:
16 × 8 Bit
7.2
IR1
IR0
AVCC
_EN
FS
-
T_
MODE
Control Register 1 (ADR 0)
FR6
FR5
FR4
FR3
FR2
FR1
P_
MODE
Control Register 2 (ADR 1)
FR12
FR11
FR10
FR9
FR8
FR7
VSOUT CLK_
_EN
ON
Control Register 3 (ADR 2)
ASK/
NFSK
Sleep
4
Sleep
3
Sleep
2
Sleep
1
Sleep
XSleep XLim
0
Control Register 4 (ADR 3)
BitChk BitChk
1
0
Lim_
min5
Lim_
min4
Lim_
min3
Lim_
min2
Lim_
min1
Lim_
min0
Control Register 5 (ADR 4)
Lim_
max2
Lim_
max1
Lim_
max0
Control Register 6 (ADR 5)
Power_ Low_
On
Batt
P_On
_Aux
Status Register (ADR 8)
Baud
1
Baud
0
Lim_
max5
Lim_
max4
Lim_
max3
ST5
ST4
ST3
ST2
ST1
OPM1 OPM0
FR0
TX/RX Data Buffer
The TX/RX data buffer is used to handle the data transfer during RX and TX operations.
37
4841D–WIRE–10/07
7.3
Control Register
To use the transceiver in different applications, it can be configured by a connected microcontroller via the 4-wire serial interface.
7.3.1
Control Register 1 (ADR 0)
Table 7-1.
IR1
IR0
0
0
Pin IRQ is set to “1” if 4 received bytes are in the TX/RX data buffer or a receiving error
occurred
0
1
Pin IRQ is set to “1” if 8 received bytes are in the TX/RX data buffer or a receiving error
occurred
1
0
Pin IRQ is set to “1” if 12 received bytes are in the TX/RX data buffer or a receiving error
occurred (default)
1
1
Pin IRQ is set to “1” if a receiving error occurred
Table 7-2.
Function (RX Mode)
Control Register 1 (Function of Bit 7 and Bit 6 in TX Mode)
IR1
IR0
0
0
Pin IRQ is set to “1” if 4 bytes remain in the TX/RX data buffer or the TX data buffer is empty
0
1
Pin IRQ is set to “1” if 8 bytes remain in the TX/RX data buffer or the TX data buffer is empty
1
0
Pin IRQ is set to “1” if 12 bytes remain in the TX/RX data buffer or the TX data buffer is
empty (default)
1
1
Pin IRQ is set to “1” if the TX data buffer is empty
Table 7-3.
Function (TX Mode)
Control Register 1 (Function of Bit 5)
AVCC_EN
Function
0
(default)
1
Enables AVCC, if the ATA5423/ATA5425 is in AUX mode
Table 7-4.
FS
Control Register 1 (Function of Bit 4)
Function (RX Mode, TX Mode)
0
Selected frequency 345/433/868/915 MHz (default)
1
Selected frequency 315 MHz
Table 7-5.
38
Control Register 1 (Function of Bit 7 and Bit 6 in RX Mode)
Control Register 1 (Function of Bit 2 and Bit 1)
OPM1
OPM0
Function
0
0
IDLE mode (default)
0
1
TX mode
1
0
RX polling mode
1
1
RX mode
ATA5423/ATA5425/ATA5428/ATA5429
4841D–WIRE–10/07
ATA5423/ATA5425/ATA5428/ATA5429
Table 7-6.
Control Register 1 (Function of Bit 0)
T_MODE
7.3.2
Function
0
TX and RX function via TX/RX data buffer (default)
1
Transparent mode, TX/RX data buffer disabled, TX modulation data stream via pin
SDI_TMDI, RX modulation data stream via pin SDO_TMDO
Control Register 2 (ADR 1)
Table 7-7.
Control Register 2 (Function of Bit 7, Bit 6, Bit 5, Bit 4, Bit 3, Bit 2 and Bit 1)
FR6
26
FR5
25
FR4
24
FR3
23
FR2
22
FR1
21
FR0
20
0
0
0
0
0
0
0
FREQ2 = 0
0
0
0
0
0
0
1
FREQ2 = 1
.
.
.
.
.
.
.
1
0
1
1
0
0
0
.
.
.
.
.
.
.
1
Note:
Function
FREQ2 = 88 (default)
1
1
1
1
1
1
FREQ2 = 127
Tuning of fRF LSBs (total 13 bits), frequency trimming resolution of fRF is fXTO/16384, which is
approximately 800 Hz (see section “XTO”, Table 4-1 on page 28)
Table 7-8.
P_MODE
Control Register 2 (Function of Bit 0 in RX Mode)
Function (RX Mode)
0
Pin IRQ is set to “1” if the bit check is successful (default)
1
No effect on pin IRQ if the bit check is successful
Table 7-9.
P_MODE
Control Register 2 (Function of Bit 0 in TX Mode)
Function (TX Mode)
0
Manchester modulator on (default)
1
Manchester modulator off (NRZ mode)
39
4841D–WIRE–10/07
7.3.3
Control Register 3 (ADR 2)
Control Register 3 (Function of Bit 7, Bit 6, Bit 5, Bit 4, Bit 3 and Bit 2)
Table 7-10.
FR12
212
FR11
211
FR8
28
FR7
27
Function
0
0
0
0
0
FREQ3 = 0
0
0
0
0
0
1
FREQ3 = 128
0
0
0
0
1
0
FREQ3 = 256
.
.
.
.
.
.
.
0
1
1
1
1
0
FREQ3 = 3840 (default)
.
.
.
.
.
.
.
1
1
1
1
1
0
FREQ3 = 7936
1
1
1
1
1
1
FREQ3 = 8064
Tuning of fRF MSBs
Table 7-11.
VSOUT_EN
0
1
Note:
0
1
Function
Output voltage power supply for external devices on (default)
This bit is set to “1” if the bit check is OK (RX_Polling, RX mode), an event at pin T1, T2, T3, T4 or
T5 occurs or the bit Power_On in the status register is “1”.
Setting VSOUT_EN = 0 in AUX mode is not allowed
CLK_ON
Note:
Control Register 3 (Function of Bit 1)
Output voltage power supply for external devices off (pin VSOUT)
Table 7-12.
Control Register 3 (Function of Bit 0)
Function
Clock output off (pin CLK)
Clock output on (default)
This bit is set to “1” if the bit check is OK (RX_Polling, RX mode), an event at pin T1, T2, T3, T4 or
T5 occurs or the bit Power_On in the status register is “1”.
Control Register 4 (ADR 3)
Table 7-13.
ASK_NFSK
40
FR9
29
0
Note:
7.3.4
FR10
210
Control Register 4 (Function of Bit 7)
Function (TX Mode, RX Mode)
0
FSK mode (default)
1
ASK mode
ATA5423/ATA5425/ATA5428/ATA5429
4841D–WIRE–10/07
ATA5423/ATA5425/ATA5428/ATA5429
Table 7-14.
Sleep4
24
Sleep3
23
Sleep2
22
Sleep1
21
Sleep0
20
Function (RX Mode)
Sleep
(TSleep = Sleep × 1024 × TDCLK × XSleep)
0
0
0
0
0
0
0
0
0
0
1
1
.
.
.
.
.
0
1
0
1
0
.
.
.
.
.
1
1
1
1
1
Table 7-15.
XSleep
31
Function
0
XSleep = 1; extended TSleep off (default)
XSleep = 8; extended TSleep on
XLim
10
(TSleep = 10 × 1024 × TDCLK × XSleep)
(default)
Control Register 4 (Function of Bit 1)
1
Table 7-16.
7.3.5
Control Register 4 (Function of Bit 6, Bit 5, Bit 4, Bit 3 and Bit 2)
Control Register 4 (Function of Bit 0)
Function
0
XLim = 1; extended TLim_min, TLim_max off (default)
1
XLim = 2; extended TLim_min, TLim_max on
Control Register 5 (ADR 4)
Table 7-17.
Control Register 5 (Function of Bit 7 and Bit 6)
BitChk1
BitChk0
Function
0
0
NBit-check = 0 (0 bits checked during bit check)
0
1
NBit-check = 3 (3 bits checked during bit check) (default)
1
0
NBit-check = 6 (6 bits checked during bit check)
1
1
NBit-check = 9 (9 bits checked during bit check)
41
4841D–WIRE–10/07
Table 7-18.
Control Register 5 (Function of Bit 5, Bit 4, Bit 3, Bit 2, Bit 1 and Bit 0 in RX Mode)
Lim_min5
Lim_min4
Lim_min3
Lim_min2
Lim_min1
Lim_min0
Function (RX Mode)
Lim_min
(Lim_min < 10 are not applicable)
(TLim_min = Lim_min × TXDCLK)
0
0
1
0
1
0
10
0
0
1
0
1
1
11
.
.
.
.
.
.
0
1
0
0
0
0
.
.
.
.
.
.
1
1
1
1
1
1
Table 7-19.
16
(TLim_min = 16 × TXDCLK)
(default)
63
Control Register 5 (Function of Bit 5, Bit 4, Bit 3, Bit 2, Bit 1 and Bit 0 in TX Mode)
Lim_min5
Lim_min4
Lim_min3
Lim_min2
Lim_min1
Lim_min0
Function (TX Mode) Lim_min
(Lim_min < 10 are not applicable)
(TX_Bitrate = 1/((Lim_min + 1) × TXDCLK × 2)
0
0
1
0
1
0
10
0
0
1
0
1
1
11
.
.
.
.
.
.
0
1
0
0
0
0
.
.
.
.
.
.
1
1
1
1
1
1
7.3.6
63
Control Register 6 (ADR 5)
Table 7-20.
42
16
(TX_Bitrate = 1/((16 + 1) × TXDCLK × 2)
(default)
Control Register 6 (Function of Bit 7 and Bit 6)
Baud1
Baud0
Function
0
0
Bit-rate range 0 (B0) 1.0 Kbit/s to 2.5 Kbit/s;
TXDCLK = 8 × TDCLK × XLim
0
1
Bit-rate range 1 (B1) 2.0 Kbit/s to 5.0 Kbit/s;
TXDCLK = 4 × TDCLK × XLim
1
0
Bit-rate range 2 (B2) 4.0 Kbit/s to 10.0 Kbit/s;
TXDCLK = 2 × TDCLK × XLim; (default)
1
1
Bit-rate range 3 (B3) 8.0 Kbit/s to 20.0 Kbit/s;
TXDCLK = 1 × TDCLK × XLim
Note that the receiver does not work with >10 Kbit/s in ASK mode
ATA5423/ATA5425/ATA5428/ATA5429
4841D–WIRE–10/07
ATA5423/ATA5425/ATA5428/ATA5429
Table 7-21.
Control Register 6 (Function of Bit 5, Bit 4, Bit 3, Bit 2, Bit 1 and Bit 0)
Lim_max5
Lim_max4
Lim_max3
Lim_max2
Lim_max1
Lim_max0
Function Lim_max
(Lim_max < 12 is not Applicable)
(TLim_max = (Lim_max – 1) × TXDCLK)
0
0
1
1
0
0
12
0
0
1
1
0
1
13
.
.
.
.
.
.
0
1
1
1
0
0
.
.
.
.
.
.
1
1
1
1
1
1
7.4
28
(TLim_max = (28 – 1) × TXDCLK)
(default)
63
Status Register
The status register indicates the current status of the transceiver and is readable via the 4-wire
serial interface. Setting Power_On or P_On_Aux or an event on ST1, ST2, ST3, ST4 or ST5 is
indicated by an IRQ.
Reading the status register resets the bits Power_On, Low_Batt, P_On_Aux and the IRQ.
7.4.1
Status Register (ADR 8)
Table 7-22.
Status Bit
Status Register
Function
ST5
Status of pin T5
Pin T5 = 0 → ST5 = 1
Pin T5 = 1 → ST5 = 0
(see Figure 7-3 on page 45)
ST4
Status of pin T4
Pin T4 = 0 → ST4 = 1
Pin T4 = 1 → ST4 = 0
(see Figure 7-3 on page 45)
ST3
Status of pin T3
Pin T3 = 0 → ST3 = 1
Pin T3 = 1 → ST3 = 0
(see Figure 7-3 on page 45)
ST2
Status of pin T2
Pin T2 = 0 → ST2 = 1
Pin T2 = 1 → ST2 = 0
(see Figure 7-3 on page 45)
ST1
Status of pin T1
Pin T1 = 0 → ST1 = 1
Pin T1 = 1 → ST1 = 0
(see Figure 7-3 on page 45)
43
4841D–WIRE–10/07
Table 7-22.
Status Bit
Function
Power_On
Indicates that the transceiver was woken up by pin PWR_ON (rising edge on pin
PWR_ON). During Power_On = 1, the bits VSOUT_EN and CLK_ON in control register 3
are set to “1”.
(see Figure 7-4 on page 46)
Low_Batt
Indicates that output voltage on pin VSOUT is too low
(VVSOUT < 2.38V typically)
(see Figure 7-5 on page 47)
P_On_Aux
7.5
Status Register (Continued)
Indicates that the auxiliary supply voltage on pin VAUX is high enough to operate.
State transition:
a) OFF mode → AUX mode (see Figure 5-2 on page 32)
b) IDLE mode (VSOUT = VS1) → IDLE mode (VSOUT = V_REG2)
(see Figure 7-6 on page 48)
Pin Tn
To switch the transceiver from OFF to IDLE mode, pin Tn must be set to “0” (maximum
0.2 × VVS2) for at least TTn_IRQ (see Figure 7-2). The transceiver recognizes the negative edge,
sets pin N_RESET to low and switches on DVCC, AVCC and the power supply for external
devices VSOUT.
If VDVCC exceeds 1.5V (typically) and the XTO is settled, the digital control logic is active and
sets the status bit STn to “1” and an interrupt is issued (TTn_IRQ).
After the voltage on pin VSOUT exceeds 2.3V (typically) and the start-up time of the XTO is
elapsed, the output clock on pin CLK is available. Because the enabling of pin CLK is asynchronous, the first clock cycle may be incomplete. N_RESET is set to high if VVSOUT exceeds 2.38V
(typically) and the XTO is settled.
Figure 7-2.
Timing Pin Tn, Status Bit STn
Tn
VThres_2 = 2.38V (typ)
VThres_1 = 2.3V (typ)
VSOUT
1.5V (typ)
DVCC, AVCC
N_RESET
CLK
TTn_IRQ
STn
(Status register)
IRQ
OFF
Mode
44
IDLE
Mode
ATA5423/ATA5425/ATA5428/ATA5429
4841D–WIRE–10/07
ATA5423/ATA5425/ATA5428/ATA5429
If the transceiver is in any active mode (IDLE, AUX, TX, RX, RX_Polling), an integrated
debounce logic is active. If there is an event on pin Tn a debounce counter is set to 0 (T = 0) and
started. The status is updated, an interrupt is issued and the debounce counter is stopped after
reaching the counter value T = 8195 × TDCLK.
An event on the same key input before reaching T = 8195 × TDCLK stops the debounce counter.
An event on an other key input before reaching T = 8195 × T DCLK resets and restarts the
debounce counter.
While the debounce counter is running, the bits VSOUT_EN and CLK_ON in control register 3
are set to “1”.
The interrupt is deleted after reading the status register or executing the command Delete_IRQ.
If pin Tn is not used, it can be left open because of an internal pull-up resistor (typically 50 kΩ).
Figure 7-3.
Timing Flow Pin Tn, Status Bit STn
IDLE Mode or
AUX Mode or
TX Mode or
RX Polling Mode or
RX Mode
Event on Pin Tn ?
N
Y
T=0
Start debounce counter
Event on Pin Tn ?
N
Y
T = 8195 × T ?
N
Y
Tn = STn ?
Y
Stop debounce counter
N
Pin Tn = 0 ?
N
Y
Stop debounce counter
STn = 1
IRQ = 1
Stop debounce counter
STn = 0
IRQ = 1
45
4841D–WIRE–10/07
7.6
Pin PWR_ON
To switch the transceiver from OFF to IDLE mode, pin PWR_ON must be set to “1” (minimum
0.8 × VVS2) for at least TPWR_ON (see Figure 7-4). The transceiver recognizes the positive edge,
sets pin N_RESET to low, and switches on DVCC, AVCC and the power supply for external
devices VSOUT.
If VDVCC exceeds 1.5V (typically) and the XTO is settled, the digital control logic is active and
sets the status bit Power_On to “1” and an interrupt is issued (TPWR_ON_IRQ_1).
After the voltage on pin VSOUT exceeds 2.3V (typically) and the start-up time of the XTO is
elapsed the output clock on pin CLK is available. Because the enabling of pin CLK is asynchronous, the first clock cycle may be incomplete. N_RESET is set to high if VVSOUT exceeds 2.38V
(typically) and the XTO is settled.
If the transceiver is in any active mode (IDLE, AUX, RX, RX_Polling, TX), a positive edge on pin
PWR_ON sets Power_On to “1” (after TPWR_ON_IRQ_2). The state transition Power_On 0 →1 generates an interrupt. If Power_On is still “1” during the positive edge on pin PWR_ON no interrupt
is issued. Power_On and the interrupt are deleted after reading the status register.
During Power_On = 1, the bits VSOUT_EN and CLK_ON in control register 3 are set to “1”.
Note:
Figure 7-4.
It is not possible to set the transceiver to OFF mode by setting pin PWR_ON to “0”. If pin
PWR_ON is not used, it must be connected to GND.
Timing Pin PWR_ON, Status Bit Power_On
TPWR_ON > TPWR_ON_IRQ_1
TPWR_ON > TPWR_ON_IRQ_2
PWR_ON
VThres_2 = 2.38V (typ)
VSOUT
VThres_1 = 2.V
(typ)
DVCC, AVCC
1.5V (typ)
N_RESET
CLK
TPWR_ON_IRQ_1
TPWR_ON_IRQ_2
Power_ON
(Status register)
IRQ
OFF
Mode
46
IDLE
Mode
IDLE, AUX, RX, RX Polling, TX
Mode
ATA5423/ATA5425/ATA5428/ATA5429
4841D–WIRE–10/07
ATA5423/ATA5425/ATA5428/ATA5429
7.7
Low Battery Indicator
The status bit Low_Batt is set to “1” if the voltage VVSOUT on pin VSOUT drops below 2.38V
(typically).
Low_Batt is set to “0” if VVSOUT exceeds VThres_2 and the status register is read via the 4-wire
serial interface (see Figure 5-3 on page 34).
Figure 7-5.
Timing Status Bit Low_Batt
IDLE, AUX, TX, RX
or
RX Polling Mode
VVSOUT < 2.38V (typ)
?
N
Y
Low_Batt = 1
Read Status Register
7.8
Pin VAUX
To switch the transceiver from OFF to AUX mode, the voltage VVAUX on pin VAUX must exceed
3.5V (typically) (see Figure 7-6 on page 48). If VVAUX exceeds 2V (typically) pin N_RESET is set
to low, and DVCC and the power supply for external devices VSOUT are switched on.
If VVAUX exceeds 3.5V (typically) the status bit P_On_Aux is set to “1” and an interrupt is issued.
After the voltage on pin VSOUT exceeds 2.3V (typically) and the start-up time of the XTO is
elapsed, the output clock on pin CLK is available. Because the enabling of pin CLK is asynchronous, the first clock cycle may be incomplete. N_RESET is set to high if VVSOUT exceeds 2.38V
(typically) and the XTO is settled.
If the transceiver is in any active mode (IDLE, TX, RX, RX_Polling), a positive edge on pin VAUX
and VVAUX > VS1 + 0.5V sets P_On_Aux to “1”. The state transition P_On_Aux 0 →1 generates
an interrupt. If P_On_Aux is still “1” during the positive edge on pin VAUX no interrupt is issued.
P_On_Aux and the interrupt are deleted after reading the status register.
47
4841D–WIRE–10/07
Figure 7-6.
Timing Pin VAUX, Status Bit P_On_Aux
VAUX
VSOUT
VVAUX > VS1 + 0.5V (typ)
3.5V (typ)
2.0V (typ)
VVAUX > VS1 + 0.5V (typ)
VThres_2 = 2.38V (typ)
VThres_1 = 2.3V (typ)
DVCC
N_RESET
CLK
P_ON_AUX
(Status register)
IRQ
OFF
Mode
48
AUX
Mode
IDLE, TX, RX, RX polling
Mode
ATA5423/ATA5425/ATA5428/ATA5429
4841D–WIRE–10/07
ATA5423/ATA5425/ATA5428/ATA5429
8. Transceiver Configuration
The configuration of the transceiver takes place via a 4-wire serial interface (CS, SCK,
SDI_TMDI, SDO_TMDO) and is organized in 8-bit units. The configuration is initiated with an
8-bit command. While shifting the command into pin SDI_TMDI, the number of bytes in the
TX/RX data buffer are available on pin SDO_TMDO. The read and write commands are followed
by one or more 8-bit data units. Each 8-bit data transmission begins with the MSB. The serial
interface is in the reset state if the level on pin CS = Low.
8.1
Command: Read TX/RX Data Buffer
During a RX operation, the user can read the received bytes in the TX/RX data buffer
successively.
Figure 8-1.
Read TX/RX Data Buffer
MSB
LSB
MSB
LSB
MSB
LSB
SDI_TMDI
Command: Read TX/RX Data Buffer
X
X
SDO_TMDO
No. Bytes in the TX/RX Data Buffer
RX Data Byte 1
RX Data Byte 1
SCK
CS
8.2
Command: Write TX/RX Data Buffer
During a TX operation the user can write the bytes in the TX/RX data buffer successively. An
echo of the command and the TX data bytes are provided for the microcontroller on pin
SDO_TMDO.
Figure 8-2.
Write TX/RX Data Buffer
MSB
LSB
MSB
LSB
MSB
LSB
SDI_TMDI
Command: Write TX/RX Data Buffer
TX Data Byte 1
TX Data Byte 2
SDO_TMDO
No. Bytes in the TX/RX Data Buffer
Write TX/RX Data Buffer
TX Data Byte 1
SCK
CS
8.3
Command: Read Control/Status Register
The control and status registers can be read individually or successively.
Figure 8-3.
Read Control/Status Register
MSB
SDI_TMDI
SDO_TMDO
LSB
MSB
LSB
MSB
LSB
Command: Read C/S Register X
Command: Read C/S Register Y
Command: Read C/S Register Z
No. Bytes in the TX/RX Data Buffer
Data C/S Register X
Data C/S Register Y
SCK
CS
49
4841D–WIRE–10/07
8.4
Command: Write Control Register
The control registers can be written individually or successively. An echo of the command and
the data bytes are provided for the microcontroller on pin SDO_TMDO.
Figure 8-4.
Write Control Register
MSB
LSB
MSB
LSB
MSB
LSB
SDI_TMDI
Command: Write Control Register X
Data Control Register X
Command: Write Control Register Y
SDO_TMDO
No. Bytes in the TX/RX Data Buffer
Write Control Register X
Data Control Register X
SCK
CS
8.5
Command: OFF Command
If AVCC_EN in control register 1 is “0”, the input level on pin PWR_ON is low and on the key
inputs Tn is high, then the OFF command sets the transceiver in the OFF mode.
Figure 8-5.
OFF Command
MSB
SDI_TMDI
SDO_TMDO
LSB
Command: OFF Command
No. Bytes in the TX/RX Data Buffer
SCK
CS
8.6
Command: Delete IRQ
The delete IRQ command sets pin IRQ to low.
Figure 8-6.
Delete IRQ
MSB
SDI_TMDI
SDO_TMDO
LSB
Command: Delete IRQ
No. Bytes in the TX/RX Data Buffer
SCK
CS
8.7
Command Structure
The three most significant bits of the command (bit 5 to bit 7) indicate the command type. Bit 0 to
bit 4 describe the target address when reading or writing a control or status register. In all other
commands bit 0 to bit 4 have no effect and should be set to “0” for compatibility with future
products.
50
ATA5423/ATA5425/ATA5428/ATA5429
4841D–WIRE–10/07
ATA5423/ATA5425/ATA5428/ATA5429
Table 8-1.
Command Structure
MSB
Command
Read TX/RX data buffer
8.8
LSB
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
0
0
0
x
x
x
x
x
Write TX/RX data buffer
0
0
1
x
x
x
x
x
Read control/status register
0
1
0
A4
A3
A2
A1
A0
Write control register
0
1
1
A4
A3
A2
A1
A0
OFF command
1
0
0
X
X
X
X
X
Delete IRQ
1
0
1
X
X
X
X
X
Not used
1
1
0
X
X
X
X
X
Not used
1
1
1
X
X
X
X
X
4-wire Serial Interface
The 4-wire serial interface consists of the Chip Select (CS), the Serial Clock (SCK), the Serial
Data Input (SDI_TMDI) and the Serial Data Output (SDO_TMDO). Data is transmitted/received
bit by bit in synchronization with the serial clock.
Note:
If the output level on pin N_RESET is low, no data communication with the microcontroller is
possible.
When CS is low and the transparent mode is inactive (T_MODE = 0), SDO_TMDO is in a high
impedance state. When CS is low and the transparent mode is active (T_MODE = 1), the RX
data stream is available on pin SDO_TMDO.
Figure 8-7.
Serial Timing
TCS_disable
CS
TCS_setup
TSCK_setup2
TCycle
TSCK_setup1
SCK
TSCK_hold
X
X
THold
TSetup
SDI_TMDI
X
MSB
TOut_enable
SDO_TMDO
X
MSB-1
X
X
TOut_delay
MSB
TOut_disable
MSB-1
LSB
X can be either ViL or ViH
51
4841D–WIRE–10/07
9. Operation Modes
9.1
RX Operation
The transceiver is set to RX operation with the bits OPM0 and OPM1 in control register 1.
Table 9-1.
Control Register 1
OPM1
OPM0
Function
1
0
RX polling mode
1
1
RX mode
The transceiver is designed to consume less than 1 mA in RX operation while remaining sensitive to signals from a corresponding transmitter. This is achieved via the polling circuit. This
circuit enables the signal path periodically for a short time. During this time the bit-check logic
verifies the presence of a valid transmitter signal. Only if a valid signal is detected does the
transceiver remain active and transfer the data to the connected microcontroller. This transfer
takes place either via the TX/RX data buffer or via the pin SDO_TMDO. When there is no valid
signal present, the transceiver is in sleep mode most of the time, resulting in low current consumption. This condition is called RX polling mode. A connected microcontroller can be disabled
during this time.
All relevant parameters of the polling logic can be configured by the connected microcontroller.
This flexibility enables the user to meet the specifications in terms of current consumption, system response time, data rate, etc.
In RX mode the RF transceiver is enabled permanently and the bit-check logic verifies the presence of a valid transmitter signal. When a valid signal is detected the transceiver transfers the
data to the connected microcontroller. This transfer take place either via the TX/RX data buffer
or via the pin SDO_TMDO.
9.1.1
RX Polling Mode
When the transceiver is in RX polling mode it stays in a continuous cycle of three different
modes. In sleep mode the RF transceiver is disabled for the time period TSleep while consuming
low current of IS = IIDLE_X. During the start-up period, TStartup_PLL and TStartup_Sig_Proc, all signal processing circuits are enabled and settled. In the following bit-check mode, the incoming data
stream is analyzed bit by bit to see if it is a valid transmitter signal. If no valid signal is present,
the transceiver is set back to sleep mode after the period TBit-check. This period varies check by
check as it is a statistical process. An average value for TBit-check is given in the electrical characteristics. During TStartup_PLL the current consumption is IS = IStartup_PLL_X. During TStartup_Sig_Proc
and TBit-check the current consumption is IS = IRX_X. The condition of the transceiver is indicated
on pin RX_ACTIVE (see Figure 9-1 on page 54 and Figure 9-2 on page 55). The average current consumption in RX polling mode IP is different in 1 Li battery application (3V), 2 Li battery
application (6V) or Base-station Application (5V). To calculate IP the index X must be replaced
by VS1,VS2 in 1 Li battery application (3V), VS2 in 2 Li battery application (6V) or VS2,VAUX in
Base-station Application (5V) (see section “Electrical Characteristics: General” on page 67).
I IDLE_X × T Sleep + I Startup_PLL_X × T Startup_PLL + I RX_X × ( T Startup_Sig_Proc + T Bitcheck )
I P = -------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------T Sleep + T Startup_PLL + T Startup_Sig_Proc + T Bit_check
52
ATA5423/ATA5425/ATA5428/ATA5429
4841D–WIRE–10/07
ATA5423/ATA5425/ATA5428/ATA5429
To save current it is recommended that CLK and VVSOUT be disabled during RX polling mode. IP
does not include the current of the Microcontroller_Interface, IVSINT, or the current of an external
device connected to pin VSOUT (for example, microcontroller). If CLK and/or VSOUT is enabled
during RX polling mode the current consumption is calculated as follows:
I S_Poll = I P + I VSINT + I EXT
During TSleep, TStartup_PLL and TStartup_Sig_Proc, the transceiver is not sensitive to a transmitter signal. To guarantee the reception of a transmitted command, the transmitter must start the
telegram with an adequate preburst. The required length of the preburst, TPreburst, depends on
the polling parameters TSleep, TStartup_PLL, TStartup_Sig_Proc and TBit-check. Thus, TBit-check depends on
the actual bit rate and the number of bits (NBit-check) to be tested.
T Preburst ≥ T Sleep + T Startup_PLL + T Startup_Sig_Proc + T Bit_check
9.1.2
Sleep Mode
The length of period TSleep is defined by the 5-bit word sleep in control register 4, the extension
factor XSleep defined by the bit XSleep in control register 4, and the basic clock cycle TDCLK. It is
calculated to be:
T Sleep = Sleep × 1024 × T DCLK × X Sleep
In US and European applications, the maximum value of TSleep is about 38 ms if XSleep is set to 1
(which is done by setting the bit XSleep in control register 4 to “0”). The time resolution is about
1.2 ms in that case. The sleep time can be extended to about 300 ms by setting XSleep to 8
(which is done by setting XSleep in control register 4 to “1”), the time resolution is then about
9.6 ms.
9.1.3
Start-up Mode
During TStartup_PLL the PLL is enabled and starts up. If the PLL is locked, the signal processing
circuit starts up (TStartup_Sig_Proc). After the start-up time all circuits are in stable condition and
ready to receive.
53
4841D–WIRE–10/07
Figure 9-1.
Flow Chart Polling Mode/RX Mode (T_MODE = 0, Transparent Mode Inactive)
Start RX Polling Mode
Sleep mode:
All circuits for analog signal processing are disabled. Only XTO and Polling logic is enabled.
Output level on pin RX_ACTIVE ⇒ Low; IS = IIDLE_X
TSleep = Sleep × 1024 × TDCLK × XSleep
Sleep:
XSleep:
TDCLK:
Defined by bits Sleep 0 to Sleep 4 in Control
Register 4
Defined by bit XSleep in Control register 4
Basic clock cycle
TStartup_PLL:
798.5 × TDCLK (typ)
TStartup_Sig_Proc:
882 × TDCLK
498 × TDCLK
306 × TDCLK
210 × TDCLK
Start RX Mode
Start-up mode:
Start-up PLL:
The PLL is enabled and locked.
Output level on pin RX_ACTIVE ⇒ High; IS = IStartup_PLL_X; IStartup_PLL
Start-up signal processing:
The signal processing circuit are enabled.
Output level on pin RX_ACTIVE ⇒ High; IS = IRX_X; TStartup_Sig_proc
(BR_Range 0)
(BR_Range 1)
(BR_Range 2)
(BR_Range 3)
Is defined by the selected baud rate range and
TDCLK .The baud-rate range is defined by bit
Baud 0 and Baud 1 in Control Register 6.
Bit-check mode:
The incomming data stream is analyzed. If the timing indicates a valid transmitter signal,
the control bits VSOUT_EN, CLK_ON and OPM0 are set to 1 and the transceiver is set to
receiving mode. Otherwise it is set to Sleep mode or to Start_up mode.
Output level on pin RX_ACTIVE ⇒ High
IS = IRX_X; TBit-check
TBit-check:
NO
Bit check
OK ?
YES
OPM0 = 1
?
Set VSOUT_EN = 1
Set CLK_ON = 1
Set OPM0 = 1
NO
YES
NO
NO
Depends on the result of the bit check.
If the bit check is ok, TBit-check depends on the
number of bits to be checked (NBit-check) and
on the utilized data rate.
If the bit check fails, the average time period for
that check despends on the selected bit-rate
range and on TXDCLK. The bit-rate range is
defined by bit Baud 0 and Baud 1 in Control
Register 6.
P_MODE = 0
?
YES
TSLEEP = 0
?
Set IRQ
YES
Receiving mode:
The incomming data stream is passed via the TX/RX Data Buffer to the connected
microcontroller. If an bit error occurs the transceiver is set back to Start-up mode.
Output level on pin RX_ACTIVE ⇒ High
IS = IRX_X
Start bit
detected ?
NO
If the transceiver detects a bit errror after a
successful bit check and before the start bit is
detected pin IRQ will be set to high (only if
P_MODE = 0) and the transceiver is set back to
start-up mode.
YES
RX data stream is
written into the TX/RX
Data Buffer
Bit error ?
NO
YES
54
ATA5423/ATA5425/ATA5428/ATA5429
4841D–WIRE–10/07
ATA5423/ATA5425/ATA5428/ATA5429
Figure 9-2.
Flow Chart Polling Mode/RX Mode (T_MODE = 1, Transparent Mode Active)
Start RX Polling Mode
Sleep mode:
All circuits for analog signal processing are disabled. Only XTO and Polling logic is enabled.
Output level on pin RX_ACTIVE ⇒ Low; IS = IIDLE_X
TSleep = Sleep × 1024 × TDCLK × XSleep
Sleep:
XSleep:
TDCLK:
Defined by bits Sleep 0 to Sleep 4 in Control
Register 4
Defined by bit XSleep in Control register 4
Basic clock cycle
TStartup_PLL:
798.5 × TDCLK (typ)
TStartup_Sig_Proc:
882 × TDCLK
498 × TDCLK
306 × TDCLK
210 × TDCLK
Start RX Mode
Start-up mode:
Start-up PLL:
The PLL is enabled and locked.
Output level on pin RX_ACTIVE ⇒ High; IS = IStartup_PLL_X; IStartup_PLL
Start-up signal processing:
The signal processing circuit are enabled.
Output level on pin RX_ACTIVE ⇒ High; IS = IRX_X; TStartup_Sig_proc
(BR_Range 0)
(BR_Range 1)
(BR_Range 2)
(BR_Range 3)
Is defined by the selected baud rate range and
TDCLK .The baud-rate range is defined by bit
Baud 0 and Baud 1 in Control Register 6.
Bit-check mode:
The incomming data stream is analyzed. If the timing indicates a valid transmitter signal,
the control bits VSOUT_EN, CLK_ON and OPM0 are set to 1 and the transceiver is set to
receiving mode. Otherwise the transceiver is set to Sleep mode
(if OPM0 = 0 and TSleep > 0) or stays in Bit-check mode.
Output level on pin RX_ACTIVE ⇒ High
IS = IRX_X; TBit-check
NO
Bit check
OK ?
YES
OPM0 = 1
?
Depends on the result of the bit check.
If the bit check is ok, TBit-check depends on the
number of bits to be checked (NBit-check) and
on the utilized data rate.
NO
YES
Set VSOUT_EN = 1
Set CLK_ON = 1
Set OPM0 = 1
NO
TBit-check:
If the bit check fails, the average time period for
that check despends on the selected bit-rate
range and on TXDCLK. The bit-rate range is
defined by bit Baud 0 and Baud 1 in Control
Register 6.
TSLEEP = 0
?
YES
Receiving mode:
The incomming data stream is passed via PIN SDO_TMDO to the connected
microcontroller. If an bit error occurs the transceiver is not set back to Start-up mode.
Output level on pin RX_ACTIVE ⇒ High
IS = IRX_X
Level on pin
CS = Low ?
NO
If in FSK mode the datastream is interrupted the
FSK-Demodulator-PLL tends to lock out and is
further not able to lock in, even there is a valid
data stream available.
In this case the transceiver must be set back to
IDLE mode.
YES
RX data stream
available on pin
SDO_TMDO
55
4841D–WIRE–10/07
9.1.4
Bit-check Mode
In bit-check mode the incoming data stream is examined to distinguish between a valid signal
from a corresponding transmitter and signals due to noise. This is done by subsequent time
frame checks where the distance between 2 signal edges are continuously compared to a programmable time window. The maximum count of this edge-to-edge test before the transceiver
switches to receiving mode is also programmable.
9.1.5
Configuration of the Bit Check
Assuming a modulation scheme that contains 2 edges per bit, two time frame checks verify one
bit. This is valid for Manchester, Bi-phase and most other modulation schemes. The maximum
count of bits to be checked can be set to 0, 3, 6 or 9 bits via the variable NBit-check in control
register 5. This implies 0, 6, 12 and 18 edge-to-edge checks, respectively. If NBit-check is set to a
higher value, the transceiver is less likely to switch to receiving mode due to noise. In the presence of a valid transmitter signal, the bit check takes less time if NBit-check is set to a lower value.
In RX polling mode, the bit-check time is not dependent on NBit-check if no valid signal is present.
Figure 9-3 shows an example where 3 bits are tested successfully.
Figure 9-3.
Timing Diagram for Complete Successful Bit Check (Number of Checked Bits: 3)
RX_ACTIVE
Bit check ok
Bit check
1/2 Bit
1/2 Bit
1/2 Bit
1/2 Bit
1/2 Bit
1/2 Bit
Demod_Out
TStartup_Sig_Proc
TBit-check
Start-up mode
Bit check mode
Receiving mode
As seen in Figure 9-4, the time window for the bit check is defined by two separate time limits. If
the edge-to-edge time tee is in between the lower bit-check limit TLim_min and the upper bit-check
limit TLim_max, the check will be continued. If tee is smaller than limit TLim_min or exceeds TLim_max,
the bit check will be terminated and the transceiver switches to sleep mode.
Figure 9-4.
Valid Time Window for Bit Check
1/fSig
Demod_Out
tee
TLim_min
TLim_max
56
ATA5423/ATA5425/ATA5428/ATA5429
4841D–WIRE–10/07
ATA5423/ATA5425/ATA5428/ATA5429
For the best noise immunity, use of a low span between TLim_min and TLim_max is recommended.
This is achieved using a fixed frequency at a 50% duty cycle for the transmitter preburst: a
“11111...” or a “10101...” sequence in Manchester or Bi-phase is a good choice. A good compromise between sensitivity and susceptibility to noise regarding the expected edge-to-edge time,
tee, is a time window of ±38%; to get the maximum sensitivity the time window should be ±50%
and then NBit-check ≥ 6. Using preburst patterns that contain various edge-to-edge time periods,
the bit-check limits must be programmed according to the required span.
The bit-check limits are determined by means of the formula below:
TLim_min = Lim_min × TXDCLK
TLim_max = (Lim_max -1) × TXDCLK
Lim_min is defined by the bits Lim_min 0 to Lim_min 5 in control register 5.
Lim_max is defined by the bits Lim_max 0 to Lim_max 5 in control register 6.
Using the above formulas, Lim_min and Lim_max can be determined according to the required
TLim_min, TLim_max and TXDCLK. The time resolution defining TLim_min and TLim_max is TXDCLK. The
minimum edge-to-edge time tee is defined in the section “Receiving Mode” on page 59. The
lower limit should be set to Lim_min ≥ 10. The maximum value of the upper limit is
Lim_max = 63.
Figure 9-5, Figure 9-6, and Figure 9-7 illustrate the bit check for the bit-check limits
Lim_min = 14 and Lim_max = 24. The signal processing circuits are enabled during TStartup_PLL
and TStartup_Sig_Proc. The output of the ASK/FSK demodulator (Demod_Out) is undefined during
that period. When the bit check becomes active, the bit-check counter is clocked with the cycle
TXDCLK.
Figure 9-5 shows how the bit check proceeds if the bit-check counter value CV_Lim is within the
limits defined by Lim_min and Lim_max at the occurrence of a signal edge. In Figure 9-6 on
page 58 the bit check fails because the value CV_Lim is lower than the limit Lim_min. The bit
check also fails if CV_Lim reaches Lim_max. This is illustrated in Figure 9-7 on page 58.
Figure 9-5.
Timing Diagram During Bit Check
(Lim_min = 14, Lim_max = 24)
RX_ACTIVE
Bit check ok
Bit check ok
Bit check
1/2 Bit
1/2 Bit
1/2 Bit
Demod_Out
Bit-check counter
0
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 9 101112131415161718 1 2 3 4 5 6 7 8 9 10 1112131415 1 2 3 4 5 6 7
TXDCLK
TStartup_Sig_Proc
Start-up mode
TBit-check
Bit check mode
57
4841D–WIRE–10/07
Figure 9-6.
Timing Diagram for Failed Bit Check (Condition CV_Lim < Lim_min)
(Lim_min = 14, Lim_max = 24)
RX_ACTIVE
Bit check failed (CV_Lim < Lim_min)
Bit check
1/2 Bit
Demod_Out
Bit-check counter
0
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 9 101112
TStartup_Sig_Proc
TBit_check
Start-up mode
Figure 9-7.
0
TSleep
Bit check mode
Sleep mode
Timing Diagram for Failed Bit Check (Condition: CV_Lim ≥ Lim_max)
(Lim_min = 14, Lim_max = 24)
RX_ACTIVE
Bit check failed (CV_Lim < Lim_min)
Bit check
1/2 Bit
Demod_Out
Bit-check counter
0
TStartup_Sig_Proc
Start-up mode
9.1.6
58
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 9 101112131415161718192021222324
TBit_check
Bit check mode
0
TSleep
Sleep mode
Duration of the Bit Check
If no transmitter is present during the bit check, the output of the ASK/FSK demodulator delivers
random signals. The bit check is a statistical process and TBit-check varies for each check. Therefore, an average value for TBit-check is given in the electrical characteristics. TBit-check depends on
the selected bit-rate range and on TXDCLK. A higher bit-rate range causes a lower value for
TBit-check, resulting in a lower current consumption in RX polling mode.
ATA5423/ATA5425/ATA5428/ATA5429
4841D–WIRE–10/07
ATA5423/ATA5425/ATA5428/ATA5429
In the presence of a valid transmitter signal, TBit-check is dependent on the frequency of that signal, fSignal, and the count of the bits, NBit-check. A higher value for NBit-check therefore results in a
longer period for TBit-check, requiring a higher value for the transmitter pre-burst, TPreburst.
9.1.7
Receiving Mode
If the bit check was successful for all bits specified by NBit-check, the transceiver switches to
receiving mode. To activate a connected microcontroller, the bits VSOUT_EN and CLK_ON in
control register 3 are set to “1”. An interrupt is issued at pin IRQ if the control bits T_MODE = 0
and P_MODE = 0.
If the transparent mode is active (T_MODE = 1) and the level on pin CS is low (no data transfer
via the serial interface), the RX data stream is available on pin SDO_TMDO (Figure 9-8).
Figure 9-8.
Receiving Mode (TMODE = 1)
Preburst
Bit check ok
Start
bit
Byte 1
Byte 2
Byte 3
Demod_Out
'0' '0' '0' '0' '0' '0' '0' '0' '0' '1' '0' '1' '0' '0' '0' '0' '0' '1' '1' '1' '1' '0' '0' '1' '1' '0' '1' '0' '1' '1' '0' '0'
SDO_TMDO
Bit-check mode
Receiving mode
If the transparent mode is inactive (T_MODE = 0), the received data stream is buffered in the
TX/RX data buffer (see Figure 9-9 on page 60). The TX/RX data buffer is only usable for
Manchester and Bi-phase coded signals. It is always possible to transfer the data from the data
buffer via the 4-wire serial interface to a microcontroller (see Figure 8-1 on page 49).
Buffering of the data stream:
After a successful bit check, the transceiver switches from bit-check mode to receiving mode. In
receiving mode the TX/RX data buffer control logic is active and examines the incoming data
stream. This is done, as in the bit check, by subsequent time frame checks where the distance
between two edges is continuously compared to a programmable time window as illustrated in
Figure 9-9 on page 60. Only two time differences between two edges in Manchester and
Bi-phase coded signals are valid (T and 2T).
The limits for T are the same as used for the bit check. They can be programmed in control
register 5 and 6 (Lim_min, Lim_max).
The limits for 2T are calculated as follows:
Lower limit of 2T:
Lim_min_2T = ( Lim_min + Lim_max ) – ( Lim_max – Lim_min )/2
T Lim_min_2T = Lim_min_2T × T XDCLK
Upper limit of 2T:
Lim_max_2T = ( Lim_min + Lim_max ) + ( Lim_max – Lim_min )/2
T Lim_max_2T = ( Lim_max_2T - 1 ) × T XDCLK
If the result of Lim_min_2T or Lim_max_2T is not an integer value, it will be rounded up.
59
4841D–WIRE–10/07
If the TX/RX data buffer control logic detects the start bit, the data stream is written in the TX/RX
data buffer byte by byte. The start bit is part of the first data byte and must be different from the
bits of the preburst. If the preburst consists of a sequence of “00000...”, the start bit must be a
“1”. If the preburst consists of a sequence of “11111...”, the start bit must be a “0”.
If the data stream consists of more than 16 bytes, a buffer overflow occurs and the TX/RX data
buffer control logic overwrites the bytes already stored in the TX/RX data buffer. Therefore, it is
very important to ensure that the data is read in time so that no buffer overflow occurs (see Figure 8-1 on page 49). There is a counter that indicates the number of received bytes in the TX/RX
data buffer (see section “Transceiver Configuration” on page 49). If a byte is transferred to the
microcontroller, the counter is decremented; if a byte is received, the counter is incremented.
The counter value is available via the 4-wire serial interface.
An interrupt is issued if the counter (while counting up) reaches the value defined by the control
bits IR0 and IR1 in control register 1.
Figure 9-9.
Receiving Mode (TMODE = 0)
Preburst
T
Bit check ok
Start
bit
Byte 1
Byte 2
Byte 3
2T
Demod_Out
'0' '0' '0' '0' '0' '0' '0' '0' '0' '1' '0' '1' '0' '0' '0' '0' '0' '1' '1' '1' '1' '0' '0' '1' '1' '0' '1' '0' '1' '1' '0' '0'
Bit-check mode
Receiving mode
TX/RX Data Buffer
Byte 16, Byte 32, ...
Byte 15, Byte 31, ...
Byte 14, Byte 30, ...
Byte 13, Byte 29, ...
Byte 12, Byte 28, ...
Byte 11, Byte 27, ...
Byte 10, Byte 26, ...
Byte 9, Byte 25, ...
Byte 8, Byte 24, ...
Byte 7, Byte 23, ...
Byte 6, Byte 22, ...
Byte 5, Byte 21, ...
Byte 4, Byte 20, ...
Byte 3, Byte 19, ...
1 1 1 1 0 0 1 1 Byte 2, Byte 18, ...
1 0 1 0 0 0 0 0 Byte 1, Byte 17, ...
MSB
LSB
Readable via 4-wire serial interface
If the TX/RX data buffer control logic detects a bit error, an interrupt is issued and the transceiver
is set back to the start-up mode (see Figure 9-1 on page 54, Figure 9-2 on page 55 and
Figure 9-10 on page 61).
Bit error:
Note:
a) tee < TLim_min or TLim_max < tee < TLim_min_2T or tee > TLim_max_2T
b) Logical error (no edge detected in the bit center)
The byte consisting of the bit error will not be stored in the TX/RX data buffer. Thus, it is not available via the 4-wire serial interface.
Writing the control register 1, 4, 5 or 6 during receiving mode resets the TX/RX data buffer control logic and the counter which indicates the number of received bytes. If the bits OPM0 and
OPM1 are still “1” after writing to a control register, the transceiver changes to the start-up mode
(start-up signal processing).
60
ATA5423/ATA5425/ATA5428/ATA5429
4841D–WIRE–10/07
ATA5423/ATA5425/ATA5428/ATA5429
Figure 9-10. Bit Error (TMODE = 0)
Bit check ok
Bit error
Demod_Out
Byte n-1
Byte n+1
Byte n
Receiving mode
Table 9-2.
Mode
Byte 1
Start-up mode Bit-check mode
Receiving mode
RX Modulation Scheme
ASK/_NFSK
0
RX
1
9.1.8
Preburst
T_MODE
RFIN
Bit in TX/RX Data
Buffer
Level on Pin
SD0_TMDO
0
fFSK_L → fFSK_H
1
X
0
fFSK_H → fFSK_L
0
X
1
fFSK_H
–
1
1
fFSK_L
–
0
0
fASK off → fASK on
1
X
0
fASK on → fASK off
0
X
1
fASK on
–
1
1
fASK off
–
0
Recommended Lim_min and Lim_max for Maximum Sensitivity
The sensitivity measurements in the section “Low-IF Receiver” in Table 3-3 on page 12 and
Table 3-4 on page 12 have been done with the Lim_min and Lim_max values according to Table
9-3. These values are optimized for maximum sensitivity. Note that since these limits are optimized for sensitivity, the number of checked bits, NBit-check, has to be at least 6 to prevent the
circuit from waking up to often in polling mode due to noise.
Table 9-3.
fRF (fXTAL)/
MHz
Recommended Lim_min and Lim_max Values for Different Bit Rates
1.0 Kbit/s
BR_Range_0
XLim = 1
2.4 Kbit/s
BR_Range_0
XLim = 0
5 Kbit/s
BR_Range_1
XLim = 0
10 Kbit/s
BR_Range_2
XLim = 0
20 Kbit/s
BR_Range_3
XLim = 0
315
Lim_min = 13 (261 µs) Lim_min = 12 (121 µs) Lim_min = 11 (55 µs) Lim_min = 11 (28 µs)
(12.73193) Lim_max = 38 (744 µs) Lim_max = 34 (332 µs) Lim_max = 32 (156 µs) Lim_max = 32 (78 µs)
Lim_min = 11 (14 µs)
Lim_max = 31 (38 µs)
345
Lim_min = 13 (239 µs) Lim_min = 12 (110 µs) Lim_min = 11 (50 µs) Lim_min = 11 (25 µs)
(13.94447) Lim_max = 38 (679 µs) Lim_max = 34 (303 µs) Lim_max = 32 (142 µs) Lim_max = 32 (71 µs)
Lim_min = 11 (13 µs)
Lim_max = 31 (34 µs)
433.92
Lim_min = 13 (251 µs) Lim_min = 12 (116 µs) Lim_min = 11 (53 µs) Lim_min = 11 (27 µs)
(13.25311) Lim_max = 38 (715 µs) Lim_max = 34 (319 µs) Lim_max = 32 (150 µs) Lim_max = 32 (75 µs)
Lim_min = 11 (13 µs)
Lim_max = 32 (37 µs)
868.3
Lim_min = 13 (248 µs) Lim_min = 12 (115 µs) Lim_min = 11 (52 µs) Lim_min = 11 (26 µs)
(13.41191) Lim_max = 38 (706 µs) Lim_max = 34 (315 µs) Lim_max = 32 (148 µs) Lim_max = 32 (74 µs)
Lim_min = 11 (13 µs)
Lim_max = 32 (37 µs)
915
Lim_min = 13 (235 µs) Lim_min = 12 (109 µs) Lim_min = 11 (50 µs) Lim_min = 11 (25 µs)
(14.13324) Lim_max = 38 (670 µs) Lim_max = 34 (299 µs) Lim_max = 32 (140 µs) Lim_max = 32 (70 µs)
Lim_min = 11 (12 µs)
Lim_max = 32 (35 µs)
61
4841D–WIRE–10/07
9.2
TX Operation
The transceiver is set to TX operation by using the bits OPM0 and OPM1 in the control
register 1.
Table 9-4.
Control Register 1
OPM1
OPM0
Function
0
1
TX mode
Before activating TX mode, the TX parameters (bit rate, modulation scheme, etc.) must be
selected as illustrated in Figure 9-11 on page 63. The bit rate depends on Baud 0 and Baud 1 in
control register 6, Lim_min0 to Lim_min5 in control register 5 and XLIM in control register 4 (see
section “Control Register” on page 38). The modulation is selected with ASK/_NFSK in control
register 4. The FSK frequency deviation is fixed to about ±16 kHz. If P_Mode is set to “1”, the
Manchester modulator is disabled and pattern mode is active (NRZ, see Table 9-5 on page 65).
After the transceiver is set to TX mode, the start-up mode is active and the PLL is enabled. If the
PLL is locked, the TX mode is active.
If the transceiver is in start-up or TX mode, the TX/RX data buffer can be loaded via the 4-wire
serial interface. After the first byte is in the buffer and the TX mode is active, the transceiver
starts transmitting automatically (beginning with the MSB). While transmitting it is always possible to load new data in the TX/RX data buffer. To prevent a buffer overflow or interruptions
during transmitting, the user must ensure that data is loaded at the same speed as it is
transmitted.
There is a counter that indicates the number of bytes to be transmitted (see section “Transceiver
Configuration” on page 49). If a byte is loaded, the counter is incremented, if a byte is transmitted, the counter is decremented. The counter value is available via the 4-wire serial interface. An
IRQ is issued if the counter (while counting down) reaches the value defined by the control bits
IR0 and IR1 in control register 1.
Note:
Writing to the control register 1, 4, 5 or 6 during TX mode resets the TX/RX data buffer and the
counter which indicates the number of bytes to be transmitted.
If T_Mode in control register 1 is set to “1”, the transceiver is in TX transparent mode. In this
mode the TX/RX data buffer is disabled and the TX data stream must be applied on pin
SDI_TMDI. Figure 9-11 on page 63 illustrates the flow chart of the TX transparent mode.
62
ATA5423/ATA5425/ATA5428/ATA5429
4841D–WIRE–10/07
ATA5423/ATA5425/ATA5428/ATA5429
Figure 9-11. TX Operation (T_MODE = 0)
Write Control Register 6
Baud1, BAUD0:
Lim_max0 to Lim_max5:
Select baud rate range
Don't care
Write Control Register 5
Lim_min0 to Lim_min5:
Bit_ck0, Bit_ck1:
Select the baud rate
Don't care
Write Control Register 4
XLim:
ASK/_NFSK:
Sleep0 to Sleep4:
XSleep:
Select the bit rate
Select modulation
Don't care
Don't care
Write Control Register 3
FR7, FR8:
VSOUT_EN:
CLK_ON:
Adjust fRF
Set VSOUT_EN = 1
Don't care
Write Control Register 2
FR0 to FR6:
P_mode:
Write Control Register 1
IR1, IR0:
AVCC_EN:
FS:
OPM1, OPM0:
T_mode:
Idle Mode
Adjust fRF
Enable or disable the
Manchester modulator
Select an event which activates
an interrupt
Don't care
Select operation frequency
Set OPM1 = 0 and OPM0 = 1
Set T_mode = 0
Write TX/RX Data Buffer (max. 16 byte)
Start-up
Mode (TX)
TStartup = 331.5 × TDCLK
N
Pin IRQ = 1 ?
Y
N
TX more Data
Bytes ?
Y
Command: Delete_IRQ
N
TX Mode
Write TX/RX Data Buffer (max. 16 - number of bytes still
in the TX/RX Data Buffer)
Pin IRQ = 1 ?
Y
Write Control Register 1
OPM1, OPM0:
Set IDLE
Idle Mode
63
4841D–WIRE–10/07
Figure 9-12. TX Transparent Mode (T_MODE = 1)
Write Control Register 4
XLim:
ASK/_NFSK:
Sleep0 to Sleep4:
XSleep:
Don't care
Select modulation
Don't care
Don't care
Write Control Register 3
FR7, FR8:
VSOUT_EN:
CLK_ON:
Adjust fRF
Set VSOUT_EN = 1
Don't care
Idle Mode
Write Control Register 2
FR0 to FR6:
P_mode:
Write Control Register 1
IR1, IR0:
AVCC_EN:
FS:
OPM1, OPM0:
T_mode:
Adjust fRF
Don't care
Don't care
Don't care
Select operation frequency
Set OPM1 = 0 and OPM0 = 1
Set T_mode = 1
Start-up
Mode (TX)
TStartup = 331.5 × TDCLK
Apply TX Data on Pin SDI_TMDI
Write Control Register 1
OPM1, OPM0:
TX Mode
Set IDLE (OPM1 = 0, OPM0 = 1
Idle Mode
64
ATA5423/ATA5425/ATA5428/ATA5429
4841D–WIRE–10/07
ATA5423/ATA5425/ATA5428/ATA5429
Table 9-5.
Mode
TX Modulation Schemes
ASK/_NFSK
P_Mode
0
T_Mode
0
Bit in TX/RX
Data Buffer
1
Level on Pin
SDI_TMDI
X
0
1
1
X
X
0
0
0
0
1
1
0
0
1
0
X
X
1
X
X
X
1
0
X
0
1
1
X
0
0
0
1
0
1
0
X
X
X
X
1
RFOUT
fFSK_L → fFSK_H
fFSK_H → fFSK_L
fFSK_H
fFSK_L
fFSK_H
fFSK_L
fASK off → fASK on
fASK on → fASK off
fASK on
fASK off
fASK on
X
1
X
0
fASK off
0
TX
1
9.3
Interrupts
Via pin IRQ, the transceiver signals different operating conditions to a connected microcontroller. If a specific operating condition occurs, pin IRQ is set to high.
If an interrupt occurs, it is recommended to delete the interrupt immediately by reading the status register, so that a further potential interrupt doesn’t get lost. If the Interrupt pin doesn’t switch
to low by reading the status register, the interrupt was triggered by the RX/TX data buffer. In this
case read or write the RX/TX data buffer according to Table 9-6.
Table 9-6.
Interrupt Handling
Operating Conditions Which Set Pin IRQ to High
Level
Operations Which Set Pin IRQ to Low Level
Events in Status Register
State transition of status bit STn
(0 → 1; 1 → 0)
Appearance of status bit Power_On
(0 → 1)
Read status register or
Command Delete IRQ
Appearance of status bit P_On_Aux
(0 → 1)
Events During TX Operation (T_MODE = 0)
4, 8 or 12 Bytes are in the TX data buffer or the TX
data buffer is empty (depends on IR0 and IR1 in
control register 1).
Write TX data buffer or
Write control register 1 or
Write control register 4 or
Write control register 5 or
Write control register 6 or
Command delete IRQ
Events During RX Operation (T_MODE = 0)
4, 8 or 12 received bytes are in the RX data buffer or a Read RX data buffer(1) or
receiving error is occurred (depends on IR0 and IR1 Write control register 1 or
in control register 1).
Write control register 4 or
Write control register 5 or
Write control register 6 or
Successful bit check (P_MODE = 0)
Command delete IRQ
Note:
1. During reading of the RX/TX buffer, no IRQ is issued, due to the received bytes or a receiving
error.
65
4841D–WIRE–10/07
10. Absolute Maximum Ratings
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating
only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this
specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
Parameters
Symbol
Min.
Max.
Unit
150
°C
Junction temperature
Tj
Storage temperature
Tstg
–55
+125
°C
Tamb
–40
+85
°C
Supply voltage VS2
VMaxVS2
–0.3
+7.2
V
Supply voltage VS1
VMaxVS1
–0.3
+4
V
Supply voltage VAUX
VMaxVAUX
–0.3
+7.2
V
Supply voltage VSINT
VMaxVSINT
–0.3
+5.5
V
ESD (Human Body Model ESD S 5.1)
every pin
HBM
–1.5
+ 1.5
kV
ESD (Machine Model JEDEC A115A)
every pin
MM
–200
+200
V
ESD (Field Induced Charge Device Model ESD
STM 5.3.1–1999)
every pin
FCDM
–1
+1
kV
Maximum input level, input matched to 50 Ω
Pin_max
10
dBm
Ambient temperature
11. Thermal Resistance
Parameters
Junction ambient
66
Symbol
Value
Unit
RthJA
25
K/W
ATA5423/ATA5425/ATA5428/ATA5429
4841D–WIRE–10/07
ATA5423/ATA5425/ATA5428/ATA5429
12. Electrical Characteristics: General
This device is manufactured with an industrial (not automotive) grade process and process controls. Although this device may
meet certain automotive grade criteria in performance, Atmel can not recommend that this device be used in any automotive
application.
All parameters refer to GND and are valid for Tamb = 25°C, VVS1 = VVS2 = 3.0V (1-battery application), VVS2 = 6.0V (2-battery application)
and VVS2 = VVAUX = 5.0V (Base-station Application). Typical values are given at fRF = 433.92 MHz unless otherwise specified. Details
about current consumption, timing and digital pin properties can be found in the specific sections of the “Electrical Characteristics”.
No. Parameters
1
1.1
1.2
1.3
1.4
Test Conditions
Pin(1)
Symbol
Min.
ATA5423
V433_N868 = AVCC
4, 10
fRF
ATA5425
V433_N868 = AVCC
4, 10
ATA5428
V433_N868 = AVCC
Typ.
Max.
Unit
Type*
312.5
317.5
MHz
A
fRF
342.5
347.5
MHz
A
4, 10
fRF
431.5
436.5
MHz
A
ATA5428
V433_N868 = GND
4, 10
fRF
862
872
MHz
A
ATA5429
V433_N868 = GND
4, 10
fRF
912.5
917.5
MHz
A
RX_TX_IDLE Mode
RF operating frequency
range
Supply current
OFF mode
Supply current
IDLE mode
System start-up time
VVS1 = VVS2 = 3V,
VVSINT = 0V
(1 battery) and
VVS2 = 6V (2 battery)
OFF mode is not
available if
VVS2 = VVAUX = 5V
VVSINT = 0V (base
station)
IS_OFF
< 10
nA
A
VVSOUT disabled,
XTO running
VVS1 = VVS2 = 3V
(1 battery)
IS_IDLE
220
µA
B
VVS2 = 6V (2 battery)
IS_IDLE
310
µA
B
VVS2 = VVAUX = 5V
(base station)
IS_IDLE
310
µA
B
TPWR_ON_IRQ_1
0.3
ms
C
From OFF mode to
IDLE mode including
reset and XTO start-up
(see Figure 7-4 on page
46)
XTAL: Cm = 5 fF,
C0 = 1.8 pF, Rm =15Ω
*) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter
Note:
1. Pin numbers in brackets mean they were measured with RF_IN matched to 50Ω according to Figure 3-1 on page 11 with
component values according to Table 3-2 on page 12 and RF_OUT matched to 50Ω according to Figure 3-10 on page 21
with component values according to Table 3-7 on page 22.
67
4841D–WIRE–10/07
12. Electrical Characteristics: General (Continued)
This device is manufactured with an industrial (not automotive) grade process and process controls. Although this device may
meet certain automotive grade criteria in performance, Atmel can not recommend that this device be used in any automotive
application.
All parameters refer to GND and are valid for Tamb = 25°C, VVS1 = VVS2 = 3.0V (1-battery application), VVS2 = 6.0V (2-battery application)
and VVS2 = VVAUX = 5.0V (Base-station Application). Typical values are given at fRF = 433.92 MHz unless otherwise specified. Details
about current consumption, timing and digital pin properties can be found in the specific sections of the “Electrical Characteristics”.
No. Parameters
Test Conditions
1.5
RX start-up time
From IDLE mode to
receiving mode
NBit-check = 3
Bit rate = 20 Kbit/s,
BR_Range_3
(see Figure 9-1 on page
54, Figure 9-2 on page
55 and Figure 9-3 on
page 56)
1.6
TX start-up time
From IDLE mode to TX
mode (see Figure 9-11
on page 63)
Pin(1)
Symbol
Min.
Typ.
Max.
Unit
Type*
TStartup_PLL +
TStartup_Sig_Proc
+ TBit-chek
1.39
ms
A
TStartup
0.4
ms
A
*) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter
Note:
68
1. Pin numbers in brackets mean they were measured with RF_IN matched to 50Ω according to Figure 3-1 on page 11 with
component values according to Table 3-2 on page 12 and RF_OUT matched to 50Ω according to Figure 3-10 on page 21
with component values according to Table 3-7 on page 22.
ATA5423/ATA5425/ATA5428/ATA5429
4841D–WIRE–10/07
ATA5423/ATA5425/ATA5428/ATA5429
12. Electrical Characteristics: General (Continued)
This device is manufactured with an industrial (not automotive) grade process and process controls. Although this device may
meet certain automotive grade criteria in performance, Atmel can not recommend that this device be used in any automotive
application.
All parameters refer to GND and are valid for Tamb = 25°C, VVS1 = VVS2 = 3.0V (1-battery application), VVS2 = 6.0V (2-battery application)
and VVS2 = VVAUX = 5.0V (Base-station Application). Typical values are given at fRF = 433.92 MHz unless otherwise specified. Details
about current consumption, timing and digital pin properties can be found in the specific sections of the “Electrical Characteristics”.
No. Parameters
2
2.1
2.2
2.3
2.4
2.5
Test Conditions
Pin(1)
Symbol
fRF = 315 MHz
fRF = 345 MHz
fRF = 433.92 MHz
17, 18
IS_RX
fRF = 868 MHz
fRF = 915 MHz
17, 18
TSleep = 49.45 ms
XSLEEP = 8, Sleep = 5
Bit rate = 20 Kbit/s FSK,
VVSOUT disabled
Min.
Typ.
Max.
Unit
Type*
10.5
mA
A
IS_RX
10.3
mA
A
17, 18
IP
444
µA
B
Bit rate 20 Kbit/s
(4)
PREF_FSK
–104.0
–106.0
–107.5
dBm
B
Bit rate 2.4 Kbit/s
(4)
PREF_FSK
–107.5
–109.5
–111.0
dBm
B
Bit rate 10 Kbit/s
(4)
PREF_ASK
–110.5
–112.5
–114.0
dBm
B
Bit rate 2.4 Kbit/s
(4)
PREF_ASK
–114.5
–116.5
–118.0
dBm
B
dB
B
Receiver/RX Mode
Supply current RX mode
Supply current
RX polling mode
Input sensitivity FSK
fRF = 433.92 MHz
Input sensitivity ASK
fRF = 433.92 MHz
Sensitivity change at
fRF = 315 MHz
fRF = 345 MHz
fRF = 868.3 MHz
fRF = 915 MHz
compared to
fRF = 433.92 MHz
FSK deviation
fDEV = ±16 kHz
limits according to
Table 9-3 on page 61,
BER = 10-3
Tamb = 25°C
ASK 100%, level of
carrier limits according
to Table 9-3 on page
61, BER = 10-3
Tamb = 25°C
fRF = 433.92 MHz
to fRF = 315 MHz
fRF = 433.92 MHz
to fRF = 345 MHz
fRF = 433.92 MHz
to fRF = 868.3 MHz
fRF = 433.92 MHz
to fRF = 915 MHz
–1.0
–0.8
+2.7
(4)
∆PREF1
+3.3
P = PREF_ASK + ∆PREF1 +
∆PREF2
P = PREF_FSK + ∆PREF1 +
∆PREF2
*) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter
Note:
1. Pin numbers in brackets mean they were measured with RF_IN matched to 50Ω according to Figure 3-1 on page 11 with
component values according to Table 3-2 on page 12 and RF_OUT matched to 50Ω according to Figure 3-10 on page 21
with component values according to Table 3-7 on page 22.
69
4841D–WIRE–10/07
12. Electrical Characteristics: General (Continued)
This device is manufactured with an industrial (not automotive) grade process and process controls. Although this device may
meet certain automotive grade criteria in performance, Atmel can not recommend that this device be used in any automotive
application.
All parameters refer to GND and are valid for Tamb = 25°C, VVS1 = VVS2 = 3.0V (1-battery application), VVS2 = 6.0V (2-battery application)
and VVS2 = VVAUX = 5.0V (Base-station Application). Typical values are given at fRF = 433.92 MHz unless otherwise specified. Details
about current consumption, timing and digital pin properties can be found in the specific sections of the “Electrical Characteristics”.
Pin(1)
Symbol
Min.
2.6
Maximum frequency
offset in FSK mode
Maximum frequency
difference of fRF
between receiver and
transmitter in FSK
mode (fRF is the center
frequency of the FSK
signal with
fDEV = ±16 kHz)
(4)
∆fOFFSET
–58
2.7
With up to 2 dB
loss of sensitivity.
Note that the tolerable
Supported FSK frequency frequency offset is for
fDEV = ±22 kHz, 6 kHz
deviation
lower than for
fDEV = ±16 kHz hence
∆fOFFSET ≤ ±52 kHz
(4)
fDEV
±14
fRF = 315 MHz
(4)
NF
fRF = 345 MHz
(4)
fRF = 433.92 MHz
(4)
No. Parameters
2.8
2.9
System noise figure
Intermediate frequency
2.10 System bandwidth
Test Conditions
Typ.
Max.
Unit
Type*
+58
kHz
B
±22
kHz
B
6.0
dB
B
NF
6.2
dB
B
NF
7.0
dB
B
±16
fRF = 868.3 MHz
(4)
NF
9.7
dB
B
fRF = 915 MHz
(4)
NF
10.3
dB
B
fRF = 315 MHz
fIF
227
kHz
A
fRF = 345 MHz
fIF
235
kHz
A
fRF = 433.92 MHz
fIF
223
kHz
A
fRF = 868.3 MHz
fIF
226
kHz
A
fRF = 915 MHz
fIF
238
kHz
A
(4)
SBW
185
kHz
A
(4)
IIP2
+50
dBm
C
This value is for
information only!
Note that for crystal and
system frequency offset
calculations, ∆fOFFSET
must be used.
∆fmeas1 = 1,800 MHz
System outband
2.11 2nd-order input intercept ∆fmeas2 = 2,026 MHz
point with respect to fIF
fIF = ∆fmeas2 – ∆fmeas1
*) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter
Note:
70
1. Pin numbers in brackets mean they were measured with RF_IN matched to 50Ω according to Figure 3-1 on page 11 with
component values according to Table 3-2 on page 12 and RF_OUT matched to 50Ω according to Figure 3-10 on page 21
with component values according to Table 3-7 on page 22.
ATA5423/ATA5425/ATA5428/ATA5429
4841D–WIRE–10/07
ATA5423/ATA5425/ATA5428/ATA5429
12. Electrical Characteristics: General (Continued)
This device is manufactured with an industrial (not automotive) grade process and process controls. Although this device may
meet certain automotive grade criteria in performance, Atmel can not recommend that this device be used in any automotive
application.
All parameters refer to GND and are valid for Tamb = 25°C, VVS1 = VVS2 = 3.0V (1-battery application), VVS2 = 6.0V (2-battery application)
and VVS2 = VVAUX = 5.0V (Base-station Application). Typical values are given at fRF = 433.92 MHz unless otherwise specified. Details
about current consumption, timing and digital pin properties can be found in the specific sections of the “Electrical Characteristics”.
No. Parameters
System outband
2.12 3rd-order input intercept
point
2.13
System outband input
1 dB compression point
2.14 LNA input impedance
Test Conditions
Pin(1)
Symbol
∆fmeas1 = 1.8 MHz
∆fmeas2 = 3.6 MHz
fRF = 315 MHz
(4)
IIP3
fRF = 345 MHz
(4)
Allowable peak RF input
level, ASK and FSK
LO spurious emission at
2.16
LNA_IN
2.17 Image rejection
Typ.
Max.
Unit
Type*
C
–22
dBm
IIP3
–22
dBm
C
fRF = 433.92 MHz
(4)
IIP3
–21
dBm
C
fRF = 868.3 MHz
(4)
IIP3
–17
dBm
C
fRF = 915 MHz
(4)
IIP3
–16
dBm
C
∆fmeas1 = 1 MHz
fRF = 315 MHz
(4)
I1dBCP
–31
dBm
C
fRF = 345 MHz
(4)
I1dBCP
–31
dBm
C
fRF = 433.92 MHz
(4)
I1dBCP
–30
dBm
C
fRF = 868.3 MHz
(4)
I1dBCP
–27
dBm
C
fRF = 915 MHz
(4)
I1dBCP
–26
dBm
C
fRF = 315 MHz
4
Zin_LNA
(44 – j233)
Ω
C
fRF = 345 MHz
4
Zin_LNA
(40 – j211)
Ω
C
fRF = 433.92 MHz
4
Zin_LNA
(32 – j169)
Ω
C
fRF = 868.3 MHz
4
Zin_LNA
(21 – j78)
Ω
C
4
Zin_LNA
(18 – j70)
Ω
C
BER < 10-3, ASK: 100%
(4)
PIN_max
+10
–10
dBm
C
FSK: fDEV = ±16 kHz
(4)
PIN_max
+10
–10
dBm
C
f < 1 GHz
(4)
–57
dBm
C
fRF = 915 MHz
2.15
Min.
–47
f >1 GHz
(4)
dBm
C
fRF = 315 MHz
(4)
–100
dBm
C
fRF = 345 MHz
(4)
–100
dBm
C
fRF = 433.92 MHz
(4)
–97
dBm
C
fRF = 868.3 MHz
(4)
–84
dBm
C
fRF = 915 MHz
(4)
–84
dBm
C
Within the complete
image band
(4)
30
dB
A
20
*) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter
Note:
1. Pin numbers in brackets mean they were measured with RF_IN matched to 50Ω according to Figure 3-1 on page 11 with
component values according to Table 3-2 on page 12 and RF_OUT matched to 50Ω according to Figure 3-10 on page 21
with component values according to Table 3-7 on page 22.
71
4841D–WIRE–10/07
12. Electrical Characteristics: General (Continued)
This device is manufactured with an industrial (not automotive) grade process and process controls. Although this device may
meet certain automotive grade criteria in performance, Atmel can not recommend that this device be used in any automotive
application.
All parameters refer to GND and are valid for Tamb = 25°C, VVS1 = VVS2 = 3.0V (1-battery application), VVS2 = 6.0V (2-battery application)
and VVS2 = VVAUX = 5.0V (Base-station Application). Typical values are given at fRF = 433.92 MHz unless otherwise specified. Details
about current consumption, timing and digital pin properties can be found in the specific sections of the “Electrical Characteristics”.
No. Parameters
Pin(1)
Symbol
(4)
FSK BR_Range_3
ASK (PRF < PRFIN_High)
Test Conditions
Peak level of useful
signal to peak level of
interferer for BER < 10-3
with any modulation
Useful signal to interfering
scheme of interferer
2.18
signal ratio
FSK BR_Ranges 0, 1, 2
Dynamic range
Lower level of range
fRF = 315 MHz
fRF = 345 MHz
fRF = 433.92 MHz
fRF = 868.3 MHz
fRF = 915 MHz
2.19 RSSI output
2.20
Output resistance RSSI
pin
Typ.
Max.
Unit
Type*
SNRFSK0-2
2
3
dB
B
(4)
SNRFSK3
4
6
dB
B
(4)
SNRASK
10
12
dB
B
(4), 36
DRSSI
70
dB
A
PRFIN_Low
–116
–115
–115
–112
–111
dBm
dBm
dBm
dBm
dBm
PRFIN_High
–46
–45
–45
–42
–41
dBm
dBm
dBm
dBm
dBm
(4), 36
Min.
Upper level of range
fRF = 315 MHz
fRF = 345 MHz
fRF = 433.92 MHz
fRF = 868.3 MHz
fRF = 915 MHz
(4), 36
Gain
(4), 36
Output voltage range
(4), 36
OVRSSI
400
36
RRSSI
8
32
RX mode
TX mode
5.5
8.0
10
40
A
A
10.5
mV/dB
A
1100
mV
A
12.5
50
kΩ
C
*) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter
Note:
72
1. Pin numbers in brackets mean they were measured with RF_IN matched to 50Ω according to Figure 3-1 on page 11 with
component values according to Table 3-2 on page 12 and RF_OUT matched to 50Ω according to Figure 3-10 on page 21
with component values according to Table 3-7 on page 22.
ATA5423/ATA5425/ATA5428/ATA5429
4841D–WIRE–10/07
ATA5423/ATA5425/ATA5428/ATA5429
12. Electrical Characteristics: General (Continued)
This device is manufactured with an industrial (not automotive) grade process and process controls. Although this device may
meet certain automotive grade criteria in performance, Atmel can not recommend that this device be used in any automotive
application.
All parameters refer to GND and are valid for Tamb = 25°C, VVS1 = VVS2 = 3.0V (1-battery application), VVS2 = 6.0V (2-battery application)
and VVS2 = VVAUX = 5.0V (Base-station Application). Typical values are given at fRF = 433.92 MHz unless otherwise specified. Details
about current consumption, timing and digital pin properties can be found in the specific sections of the “Electrical Characteristics”.
No. Parameters
Pin(1)
Test Conditions
Symbol
Min.
Typ.
Max.
Unit
Type*
dBC
C
dBC
C
dBC
C
dBC
C
dBC
C
nF
D
–3
Sensitivity (BER = 10 )
is reduced by 6 dB if a
continuous wave
blocking signal at ±∆f is
∆PBlock higher than the
useful signal level
(bit rate = 20 Kbit/s,
FSK, fDEV ±16kHz,
Manchester code)
fRF = 315 MHz
∆f ±0.75 MHz
∆f ±1.0 MHz
∆f ±1.5 MHz
∆f ±5 MHz
∆f ±10 MHz
2.21 Blocking
fRF = 345 MHz
∆f ±0.75 MHz
∆f ±1.0 MHz
∆f ±1.5 MHz
∆f ±5 MHz
∆f ±10 MHz
fRF = 433.92 MHz
∆f ±0.75 MHz
∆f ±1.0 MHz
∆f ±1.5 MHz
∆f ±5 MHz
∆f ±10 MHz
fRF = 868.3 MHz
∆f ±0.75 MHz
∆f ±1.0 MHz
∆f ±1.5 MHz
∆f ±5 MHz
∆f ±10 MHz
2.22 CDEM
(4)
(4)
(4)
(4)
fRF = 915 MHz
∆f ±0.75 MHz
∆f ±1.0 MHz
∆f ±1.5 MHz
∆f ±5 MHz
∆f ±10 MHz
(4)
Capacitor connected to
pin 37 (CDEM)
37
56
60
63
69
71
∆PBlock
56
60
63
69
71
∆PBlock
55
59
62
68
70
∆PBlock
50
53
57
67
69
∆PBlock
50
53
57
67
69
∆PBlock
–5%
15
+5%
*) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter
Note:
1. Pin numbers in brackets mean they were measured with RF_IN matched to 50Ω according to Figure 3-1 on page 11 with
component values according to Table 3-2 on page 12 and RF_OUT matched to 50Ω according to Figure 3-10 on page 21
with component values according to Table 3-7 on page 22.
73
4841D–WIRE–10/07
12. Electrical Characteristics: General (Continued)
This device is manufactured with an industrial (not automotive) grade process and process controls. Although this device may
meet certain automotive grade criteria in performance, Atmel can not recommend that this device be used in any automotive
application.
All parameters refer to GND and are valid for Tamb = 25°C, VVS1 = VVS2 = 3.0V (1-battery application), VVS2 = 6.0V (2-battery application)
and VVS2 = VVAUX = 5.0V (Base-station Application). Typical values are given at fRF = 433.92 MHz unless otherwise specified. Details
about current consumption, timing and digital pin properties can be found in the specific sections of the “Electrical Characteristics”.
No. Parameters
3
3.1
Test Conditions
Pin(1)
Symbol
Min.
Typ.
Max.
Unit
Type*
Power Amplifier/TX Mode
Supply current TX mode
power amplifier OFF
fRF = 868.3 MHz
fRF = 915 MHz
IS_TX_PAOFF
6.50
mA
A
fRF = 315 MHz
fRF = 345 MHz
fRF = 433.92 MHz
IS_TX_PAOFF
6.95
mA
A
dBm
B
VVS1 = VVS2 = 3V
Tamb = 25°C
VPWR_H = 0V
fRF = 315 MHz
RR_PWR = 56 kΩ
RLopt = 2.5 kΩ
fRF = 345 MHz
RR_PWR = 56 kΩ
RLopt = 2.4 kΩ
3.2
Output power 1
fRF = 433.92 MHz
RR_PWR = 56 kΩ
RLopt = 2.3 kΩ
–2.5
(10)
PREF1
PA on/0 dBm
fRF = 315 MHz
17, 18
IS_TX_PAON1
8.5
mA
B
fRF = 345 MHz
17, 18
IS_TX_PAON1
8.6
mA
B
fRF = 433.92 MHz
17, 18
IS_TX_PAON1
8.6
mA
B
fRF = 868.3 MHz
17, 18
IS_TX_PAON1
9.6
mA
B
fRF = 915 MHz
17, 18
IS_TX_PAON1
9.6
mA
B
0
+2.5
fRF = 868.3 MHz
RR_PWR = 30 kΩ
RLopt = 1.3 kΩ
fRF = 915 MHz
RR_PWR = 33 kΩ
RLopt = 1.1 kΩ
RF_OUT matched to
RLopt //
j/(2 × π × fRF × 1.0 pF)
3.3
Supply current TX mode
power amplifier ON 1
*) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter
Note:
74
1. Pin numbers in brackets mean they were measured with RF_IN matched to 50Ω according to Figure 3-1 on page 11 with
component values according to Table 3-2 on page 12 and RF_OUT matched to 50Ω according to Figure 3-10 on page 21
with component values according to Table 3-7 on page 22.
ATA5423/ATA5425/ATA5428/ATA5429
4841D–WIRE–10/07
ATA5423/ATA5425/ATA5428/ATA5429
12. Electrical Characteristics: General (Continued)
This device is manufactured with an industrial (not automotive) grade process and process controls. Although this device may
meet certain automotive grade criteria in performance, Atmel can not recommend that this device be used in any automotive
application.
All parameters refer to GND and are valid for Tamb = 25°C, VVS1 = VVS2 = 3.0V (1-battery application), VVS2 = 6.0V (2-battery application)
and VVS2 = VVAUX = 5.0V (Base-station Application). Typical values are given at fRF = 433.92 MHz unless otherwise specified. Details
about current consumption, timing and digital pin properties can be found in the specific sections of the “Electrical Characteristics”.
No. Parameters
Test Conditions
Pin(1)
Symbol
Min.
Typ.
Max.
Unit
Type*
(10)
PREF2
3.5
5.0
6.5
dBm
B
17, 18
IS_TX_PAON2
10.3
mA
B
VVS1 = VVS2 = 3V
Tamb = 25°C
VPWR_H = 0V
fRF = 315 MHz
RR_PWR = 30 kΩ
RLopt = 1.0 kΩ
fRF = 345 MHz
RR_PWR = 33 kΩ
RLopt = 1.1 kΩ
3.4
Output power 2
fRF = 433.92 MHz
RR_PWR = 27 kΩ
RLopt = 1.1 kΩ
fRF = 868.3 MHz
RR_PWR = 16 kΩ
RLopt = 0.5 kΩ
fRF = 915 MHz
RR_PWR = 15 kΩ
RLopt = 0.25 kΩ
RF_OUT matched to
RLopt//
j/(2 × π × fRF × 1.0 pF)
PA on/5 dBm
fRF = 315 MHz
3.5
Supply current TX mode
power amplifier ON 2
fRF = 345 MHz
17, 18
IS_TX_PAON2
10.4
mA
B
fRF = 433.92 MHz
17, 18
IS_TX_PAON2
10.5
mA
B
fRF = 868.3 MHz
17, 18
IS_TX_PAON2
11.2
mA
B
fRF = 915 MHz
17, 18
IS_TX_PAON2
11.8
mA
B
*) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter
Note:
1. Pin numbers in brackets mean they were measured with RF_IN matched to 50Ω according to Figure 3-1 on page 11 with
component values according to Table 3-2 on page 12 and RF_OUT matched to 50Ω according to Figure 3-10 on page 21
with component values according to Table 3-7 on page 22.
75
4841D–WIRE–10/07
12. Electrical Characteristics: General (Continued)
This device is manufactured with an industrial (not automotive) grade process and process controls. Although this device may
meet certain automotive grade criteria in performance, Atmel can not recommend that this device be used in any automotive
application.
All parameters refer to GND and are valid for Tamb = 25°C, VVS1 = VVS2 = 3.0V (1-battery application), VVS2 = 6.0V (2-battery application)
and VVS2 = VVAUX = 5.0V (Base-station Application). Typical values are given at fRF = 433.92 MHz unless otherwise specified. Details
about current consumption, timing and digital pin properties can be found in the specific sections of the “Electrical Characteristics”.
No. Parameters
Test Conditions
Pin(1)
Symbol
Min.
Typ.
Max.
Unit
Type*
(10)
PREF3
8.5
10
11.5
dBm
B
17, 18
IS_TX_PAON3
15.7
mA
B
VVS1 = VVS2 = 3V
Tamb = 25°C
VPWR_H = AVCC
fRF = 315 MHz
RR_PWR = 30 kΩ
RLopt = 0.38 kΩ
fRF = 345 MHz
RR_PWR = 31 kΩ
RLopt = 0.38 kΩ
3.6
Output power 3
fRF = 433.92 MHz
RR_PWR = 27 kΩ
RLopt = 0.36 kΩ
fRF = 868.3 MHz
RR_PWR = 20 kΩ
RLopt = 0.22 kΩ
fRF = 915 MHz
RR_PWR = 16 kΩ
RLopt = 0.24 kΩ
RF_OUT matched to
RLopt//
j/(2 × π × fRF × 1.0 pF)
PA on/10dBm
fRF = 315 MHz
3.7
3.8
Supply current TX mode
power amplifier ON 3
fRF = 345 MHz
17, 18
IS_TX_PAON3
15.8
mA
B
fRF = 433.92 MHz
17, 18
IS_TX_PAON3
15.8
mA
B
fRF = 868.3 MHz
17, 18
IS_TX_PAON3
17.3
mA
B
fRF = 915 MHz
17, 18
IS_TX_PAON3
19.3
mA
B
(10)
∆PREF
–0.8
–1.5
dB
B
(10)
∆PREF
–2.5
dB
B
(10)
∆PREF
–3.5
dB
B
Tamb = –40°C to +85°C
Pout = PREFX + ∆PREFX
Output power variation for X = 1, 2 or 3
full temperature and
VVS1 = VVS2 = 3.0V
supply voltage range
VVS1 = VVS2 = 2.7V
VVS1 = VVS2 = 2.4V
*) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter
Note:
76
1. Pin numbers in brackets mean they were measured with RF_IN matched to 50Ω according to Figure 3-1 on page 11 with
component values according to Table 3-2 on page 12 and RF_OUT matched to 50Ω according to Figure 3-10 on page 21
with component values according to Table 3-7 on page 22.
ATA5423/ATA5425/ATA5428/ATA5429
4841D–WIRE–10/07
ATA5423/ATA5425/ATA5428/ATA5429
12. Electrical Characteristics: General (Continued)
This device is manufactured with an industrial (not automotive) grade process and process controls. Although this device may
meet certain automotive grade criteria in performance, Atmel can not recommend that this device be used in any automotive
application.
All parameters refer to GND and are valid for Tamb = 25°C, VVS1 = VVS2 = 3.0V (1-battery application), VVS2 = 6.0V (2-battery application)
and VVS2 = VVAUX = 5.0V (Base-station Application). Typical values are given at fRF = 433.92 MHz unless otherwise specified. Details
about current consumption, timing and digital pin properties can be found in the specific sections of the “Electrical Characteristics”.
No. Parameters
3.9
3.10
Impedance RF_OUT in
RX mode
Noise floor power
amplifier
3.11 ASK modulation rate
4
4.1
Test Conditions
Pin(1)
Symbol
Min.
Typ.
Max.
Unit
Type*
fRF = 315 MHz
10
ZRF_OUT_RX
(36 – j502)
Ω
C
fRF = 345 MHz
10
ZRF_OUT_RX
(33 – j480)
Ω
C
fRF = 433.92 MHz
10
ZRF_OUT_RX
(19 – j366)
Ω
C
fRF = 868.3 MHz
10
ZRF_OUT_RX
(2.8 – j141)
Ω
C
fRF = 915 MHz
10
ZRF_OUT_RX
(2.6 – j135)
Ω
C
at ±10 MHz/at 5 dBm
fRF = 315 MHz
(10)
LTX10M
–127
dBC/Hz
C
fRF = 345 MHz
(10)
LTX10M
–126
dBC/Hz
C
fRF = 433.92 MHz
(10)
LTX10M
–126
dBC/Hz
C
fRF = 868.3 MHz
(10)
LTX10M
–125
dBC/Hz
C
fRF = 915 MHz
(10)
LTX10M
–125
dBC/Hz
C
kHz
C
This corresponds to
10 Kbit/s Manchester
coding and 20 Kbit/s
NRZ coding
fData_ASK
1
10
XTO
Pulling XTO due to XTO,
CL1 and CL2 tolerances
Pulling at nominal
temperature and supply
voltage
fXTAL = resonant
frequency of the XTAL
C0 ≥ 1.0 pF
Rm ≤ 120Ω
24, 25
Cm ≤ 7.0 fF
Cm ≤ 14 fF
4.2
At start-up; after
Transconductance XTO at
start-up the amplitude
start
is regulated to VPPXTAL
4.3
XTO start-up time
4.4
4.5
A
∆fXTO1
–50
–100
fXTAL
24, 25
gm, XTO
19
C0 ≤ 2.2 pF
Cm < 14fF
Rm ≤ 120Ω
24, 25
TPWR_ON_IRQ_1
300
Maximum C0 of XTAL
Required for stable
operation with internal
load capacitors
24, 25
C0max
Internal capacitors
CL1 and CL2
24, 25
CL1, CL2
14.8
18 pF
+50
+100
ppm
ms
B
800
µs
A
3.8
pF
D
21.2
pF
B
*) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter
Note:
1. Pin numbers in brackets mean they were measured with RF_IN matched to 50Ω according to Figure 3-1 on page 11 with
component values according to Table 3-2 on page 12 and RF_OUT matched to 50Ω according to Figure 3-10 on page 21
with component values according to Table 3-7 on page 22.
77
4841D–WIRE–10/07
12. Electrical Characteristics: General (Continued)
This device is manufactured with an industrial (not automotive) grade process and process controls. Although this device may
meet certain automotive grade criteria in performance, Atmel can not recommend that this device be used in any automotive
application.
All parameters refer to GND and are valid for Tamb = 25°C, VVS1 = VVS2 = 3.0V (1-battery application), VVS2 = 6.0V (2-battery application)
and VVS2 = VVAUX = 5.0V (Base-station Application). Typical values are given at fRF = 433.92 MHz unless otherwise specified. Details
about current consumption, timing and digital pin properties can be found in the specific sections of the “Electrical Characteristics”.
Pin(1)
Symbol
Min.
4, 10
∆fXTO2
–2
V(XTAL1, XTAL2)
peak-to-peak value
24, 25
VPPXTAL
V(XTAL1)
peak-to-peak value
24, 25
4.8
Real part of XTO
impedance at start-up
4.9
Max.
Unit
Type*
+2
ppm
C
700
mVpp
C
VPPXTAL
350
mVpp
C
C0 ≤ 2.2 pF, small signal
start impedance, this
24, 25
value is important for
crystal oscillator startup
ReXTO
–2,000
–1,500
Ω
B
Maximum series
resistance Rm of XTAL
after start-up
C0 ≤ 2.2 pF
Cm ≤ 14 fFΩ
Rm_max
15
120
Ω
B
Nominal XTAL load
resonant frequency
fRF = 315 MHz
fRF = 345 MHz
fRF = 433.92 MHz
fRF = 868.3 MHz
fRF = 915 MHz
fXTAL
12.73193
13.94447
13.25311
13.41191
14.13324
MHz
MHz
MHz
MHz
MHz
D
No. Parameters
4.6
Test Conditions
1.0 pF ≤ C0 ≤ 2.2 pF
C ≤ 14.0 fF
Pulling of radio frequency m
Rm ≤120Ω
fRF due to XTO, CL1 and
PLL adjusted with
CL2 versus temperature
FREQ at nominal
and supply changes
temperature and supply
voltage
Typ.
Cm = 5 fF, C0 = 1.8 pF
Rm =15Ω
4.7
4.10
Amplitude XTAL after
start-up
24, 25
24, 25
*) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter
Note:
78
1. Pin numbers in brackets mean they were measured with RF_IN matched to 50Ω according to Figure 3-1 on page 11 with
component values according to Table 3-2 on page 12 and RF_OUT matched to 50Ω according to Figure 3-10 on page 21
with component values according to Table 3-7 on page 22.
ATA5423/ATA5425/ATA5428/ATA5429
4841D–WIRE–10/07
ATA5423/ATA5425/ATA5428/ATA5429
12. Electrical Characteristics: General (Continued)
This device is manufactured with an industrial (not automotive) grade process and process controls. Although this device may
meet certain automotive grade criteria in performance, Atmel can not recommend that this device be used in any automotive
application.
All parameters refer to GND and are valid for Tamb = 25°C, VVS1 = VVS2 = 3.0V (1-battery application), VVS2 = 6.0V (2-battery application)
and VVS2 = VVAUX = 5.0V (Base-station Application). Typical values are given at fRF = 433.92 MHz unless otherwise specified. Details
about current consumption, timing and digital pin properties can be found in the specific sections of the “Electrical Characteristics”.
No. Parameters
4.11 External CLK frequency
Pin(1)
Symbol
fRF = 315 MHz
CLK division ratio = 3
CLK has nominal 50%
duty cycle
30
fCLK
fRF = 345 MHz
CLK division ratio = 3
CLK has nominal 50%
duty cycle
30
fRF = 433.92 MHz
CLK division ratio = 3
CLK has nominal 50%
duty cycle
Unit
Type*
4.244
MHz
D
fCLK
4.648
MHz
D
30
fCLK
4.418
MHz
D
fRF = 868.3 MHz
CLK division ratio = 3
CLK has nominal 50%
duty cycle
30
fCLK
4.471
MHz
D
fRF = 915 MHz
CLK division ratio = 3
CLK has nominal 50%
duty cycle
30
fCLK
4.711
MHz
D
24, 25
VDCXTO
–30
mV
C
Test Conditions
VDC(XTAL1, XTAL2)
XTO running
4.12 DC voltage after start-up
(IDLE mode, RX mode
and TX mode)
Min.
–150
Typ.
Max.
*) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter
Note:
1. Pin numbers in brackets mean they were measured with RF_IN matched to 50Ω according to Figure 3-1 on page 11 with
component values according to Table 3-2 on page 12 and RF_OUT matched to 50Ω according to Figure 3-10 on page 21
with component values according to Table 3-7 on page 22.
79
4841D–WIRE–10/07
12. Electrical Characteristics: General (Continued)
This device is manufactured with an industrial (not automotive) grade process and process controls. Although this device may
meet certain automotive grade criteria in performance, Atmel can not recommend that this device be used in any automotive
application.
All parameters refer to GND and are valid for Tamb = 25°C, VVS1 = VVS2 = 3.0V (1-battery application), VVS2 = 6.0V (2-battery application)
and VVS2 = VVAUX = 5.0V (Base-station Application). Typical values are given at fRF = 433.92 MHz unless otherwise specified. Details
about current consumption, timing and digital pin properties can be found in the specific sections of the “Electrical Characteristics”.
No. Parameters
5
5.1
5.2
5.3
5.4
5.5
Test Conditions
Pin(1)
Symbol
Min.
Typ.
Max.
Unit
Type*
dBC
C
dBC
C
dBC
C
dBC
C
dBC/Hz
A
LRX1M
–121
–120
–120
–113
–113
dBC/Hz
C
LTX1M
–113
–113
–111
–107
–107
dBC/Hz
C
Synthesizer
At ±fCLK, CLK enabled
fRF = 315 MHz
fRF = 345 MHz
fRF = 433.92 MHz
fRF = 868.3 MHz
fRF = 915 MHz
SPTX
–72
–74
–68
–70
–69
SPTX
–70
–68
–66
–60
–60
SPRX
< –75
< –75
< –75
< –75
< –75
At ±fXTO
fRF = 315 MHz
fRF = 345 MHz
fRF = 433.92 MHz
fRF = 868.3 MHz
fRF = 915 MHz
SPRX
–75
–73
–75
–68
–67
In loop phase noise
TX mode
Measured at 20 kHz
distance to carrier
fRF = 315 MHz
fRF = 345 MHz
fRF = 433.92 MHz
fRF = 868.3 MHz
fRF = 915 MHz
LTX20k
Phase noise at 1M
RX mode
fRF = 315 MHz
fRF = 345 MHz
fRF = 433.92 MHz
fRF = 868.3 MHz
fRF = 915 MHz
Phase noise at 1M
TX mode
fRF = 315 MHz
fRF = 345 MHz
fRF = 433.92 MHz
fRF = 868.3 MHz
fRF = 915 MHz
Spurious TX mode
Spurious RX mode
At ±fXTO
fRF = 315 MHz
fRF = 345 MHz
fRF = 433.92 MHz
fRF = 868.3 MHz
fRF = 915 MHz
At ±fCLK, CLK enabled
fRF = 315 MHz
fRF = 345 MHz
fRF = 433.92 MHz
fRF = 868.3 MHz
fRF = 915 MHz
–85
–85
–80
–75
–75
*) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter
Note:
80
1. Pin numbers in brackets mean they were measured with RF_IN matched to 50Ω according to Figure 3-1 on page 11 with
component values according to Table 3-2 on page 12 and RF_OUT matched to 50Ω according to Figure 3-10 on page 21
with component values according to Table 3-7 on page 22.
ATA5423/ATA5425/ATA5428/ATA5429
4841D–WIRE–10/07
ATA5423/ATA5425/ATA5428/ATA5429
12. Electrical Characteristics: General (Continued)
This device is manufactured with an industrial (not automotive) grade process and process controls. Although this device may
meet certain automotive grade criteria in performance, Atmel can not recommend that this device be used in any automotive
application.
All parameters refer to GND and are valid for Tamb = 25°C, VVS1 = VVS2 = 3.0V (1-battery application), VVS2 = 6.0V (2-battery application)
and VVS2 = VVAUX = 5.0V (Base-station Application). Typical values are given at fRF = 433.92 MHz unless otherwise specified. Details
about current consumption, timing and digital pin properties can be found in the specific sections of the “Electrical Characteristics”.
No. Parameters
Test Conditions
Pin(1)
Symbol
Min.
Typ.
Max.
Unit
Type*
5.6
Phase noise at 10M
RX mode
Noise floor PLL
LRX10M
–135
dBC/Hz
C
5.7
Loop bandwidth PLL
TX mode
Frequency where the
absolute value loop
gain is equal to 1
fLoop_PLL
70
kHz
B
Frequency deviation
TX mode
fRF = 315 MHz
fRF = 345 MHz
fRF = 433.92 MHz
fRF = 868.3 MHz
fRF = 915 MHz
fDEV_TX
±15.54
±17.02
±16.17
±16.37
±17.25
kHz
D
Frequency resolution
fRF = 315 MHz
fRF = 345 MHz
fRF = 433.92 MHz
fRF = 868.3 MHz
fRF = 915 MHz
∆fStep_PLL
777.1
851.1
808.9
818.6
862.6
Hz
D
kHz
B
5.8
5.9
5.10 FSK modulation rate
6
This correspond to
20 Kbit/s Manchester
coding and 40 Kbit/s
NRZ coding
6.2
fData_FSK
1
20
RX/TX Switch
RX mode, pin 38 with
short connection to
GND, fRF = 0 Hz (DC)
6.1
4, 10
Impedance RX mode
Impedance TX mode
39
ZSwitch_RX
23000
Ω
A
Ω
C
fRF = 315 MHz
fRF = 345 MHz
fRF = 433.92 MHz
fRF = 868.3 MHz
fRF = 915 MHz
39
ZSwitch_RX
(11.3 – j214)
(11.1 – j181)
(10.3 – j153)
(8.9 – j73)
(9 – j65)
TX mode, pin 38 with
short connection to
GND, fRF = 0 Hz (DC)
39
ZSwitch_TX
5
Ω
A
ZSwitch_RX
(4.8 + j3.2)
(4.7 + j3.4)
(4.5 + j4.3)
(5 + j9)
(5 + j9.2)
Ω
C
fRF = 315 MHz
fRF = 345 MHz
fRF = 433.92 MHz
fRF = 868.3 MHz
fRF = 915 MHz
39
*) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter
Note:
1. Pin numbers in brackets mean they were measured with RF_IN matched to 50Ω according to Figure 3-1 on page 11 with
component values according to Table 3-2 on page 12 and RF_OUT matched to 50Ω according to Figure 3-10 on page 21
with component values according to Table 3-7 on page 22.
81
4841D–WIRE–10/07
12. Electrical Characteristics: General (Continued)
This device is manufactured with an industrial (not automotive) grade process and process controls. Although this device may
meet certain automotive grade criteria in performance, Atmel can not recommend that this device be used in any automotive
application.
All parameters refer to GND and are valid for Tamb = 25°C, VVS1 = VVS2 = 3.0V (1-battery application), VVS2 = 6.0V (2-battery application)
and VVS2 = VVAUX = 5.0V (Base-station Application). Typical values are given at fRF = 433.92 MHz unless otherwise specified. Details
about current consumption, timing and digital pin properties can be found in the specific sections of the “Electrical Characteristics”.
No. Parameters
7
7.1
7.2
7.4
Test Conditions
Pin(1)
Symbol
Min.
Typ.
Max.
Unit
Type*
5.25
V
A
Microcontroller Interface
Voltage range for
microcontroller interface
IVSINT < 10 µA if CLK is
disabled and all
interface pins are in
stable condition and
unloaded
CLK output rise and fall
time
fCLK < 4.5 MHz
CL = 10 pF
CL = Load capacitance
on pin CLK
2.4V ≤ VVSINT ≤ 5.25V
20% to 80% VVSINT
Current consumption of
the microcontroller
interface
27, 28,
29, 30,
31, 32,
33, 34,
35
30
2.4
trise
20
30
ns
tfall
20
30
ns
CLK enabled
VVSOUT enabled
( C CLK + C L ) × V VSINT × f XTO
I VSINT = --------------------------------------------------------------------------3
CLK disabled
VVSOUT enabled
< 10 µA
VVSOUT disabled
27
IVSINT
30, 27
CCLK
B
< 10 µA
CL = Load capacitance
on pin CLK
(All interface pins,
except pin CLK, are in
stable condition and
unloaded)
7.5
Internal equivalent
capacitance
Used for current
calculation
8
pF
B
*) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter
Note:
82
1. Pin numbers in brackets mean they were measured with RF_IN matched to 50Ω according to Figure 3-1 on page 11 with
component values according to Table 3-2 on page 12 and RF_OUT matched to 50Ω according to Figure 3-10 on page 21
with component values according to Table 3-7 on page 22.
ATA5423/ATA5425/ATA5428/ATA5429
4841D–WIRE–10/07
ATA5423/ATA5425/ATA5428/ATA5429
12. Electrical Characteristics: General (Continued)
This device is manufactured with an industrial (not automotive) grade process and process controls. Although this device may
meet certain automotive grade criteria in performance, Atmel can not recommend that this device be used in any automotive
application.
All parameters refer to GND and are valid for Tamb = 25°C, VVS1 = VVS2 = 3.0V (1-battery application), VVS2 = 6.0V (2-battery application)
and VVS2 = VVAUX = 5.0V (Base-station Application). Typical values are given at fRF = 433.92 MHz unless otherwise specified. Details
about current consumption, timing and digital pin properties can be found in the specific sections of the “Electrical Characteristics”.
No. Parameters
8
Test Conditions
Pin(1)
Symbol
Min.
Typ.
Max.
Unit
Type*
V
A
Power Supply General Definitions and AUX Mode
IVSINT
VSINT
IEXT = IVSOUT – IVSINT
VSOUT
8.1
IVSOUT IEXT
Current consumption of
an external device
connected to pin VSOUT
IEXT
IEXT = IVSOUT
IVSINT
VSINT
VSOUT
IEXT = IVSOUT
IAUX_VAUX
8.2
8.3
VAUX
AUX mode
Power supply output
voltage
AUX mode
VVAUX ≥ 4V
IVSOUT ≤ 13.5 mA
(3.25V regulator mode,
V_REG2, see
Figure 5-1 on page 30)
22
VVSOUT
2.7
3.5
*) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter
Note:
1. Pin numbers in brackets mean they were measured with RF_IN matched to 50Ω according to Figure 3-1 on page 11 with
component values according to Table 3-2 on page 12 and RF_OUT matched to 50Ω according to Figure 3-10 on page 21
with component values according to Table 3-7 on page 22.
83
4841D–WIRE–10/07
12. Electrical Characteristics: General (Continued)
This device is manufactured with an industrial (not automotive) grade process and process controls. Although this device may
meet certain automotive grade criteria in performance, Atmel can not recommend that this device be used in any automotive
application.
All parameters refer to GND and are valid for Tamb = 25°C, VVS1 = VVS2 = 3.0V (1-battery application), VVS2 = 6.0V (2-battery application)
and VVS2 = VVAUX = 5.0V (Base-station Application). Typical values are given at fRF = 433.92 MHz unless otherwise specified. Details
about current consumption, timing and digital pin properties can be found in the specific sections of the “Electrical Characteristics”.
No. Parameters
8.4
8.5
8.6
Current in AUX mode on
pin VAUX
Supply current
AUX mode
Supported voltage range
VAUX
Test Conditions
Pin(1)
Symbol
IVSOUT = 0
VVAUX = 6V
VVAUX = 4V to 7V
19
IAUX_VAUX
19, 22,
27
IS_AUX
19
VVAUX
CLK enabled
VVSOUT enabled
CLK disabled
VVSOUT enabled
Min.
Typ.
Max.
Unit
Type*
380
500
500
µA
µA
B
IS_AUX = IAUX_VAUX + IVSINT + IEXT
IS_AUX = IAUX_VAUX + IEXT
4
6
7
V
*) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter
Note:
84
1. Pin numbers in brackets mean they were measured with RF_IN matched to 50Ω according to Figure 3-1 on page 11 with
component values according to Table 3-2 on page 12 and RF_OUT matched to 50Ω according to Figure 3-10 on page 21
with component values according to Table 3-7 on page 22.
ATA5423/ATA5425/ATA5428/ATA5429
4841D–WIRE–10/07
ATA5423/ATA5425/ATA5428/ATA5429
13. Electrical Characteristics: 1 Li Battery Application (3V)
All parameters refer to GND and are valid for Tamb = 25°C, VVS1 = VVS2 = 3.0V. Application according to Figure 2-1 on page 7.
fRF = 315 MHz/345 MHz/433.92 MHz/868.3 MHz/915 MHz unless otherwise specified
No.
9
Parameters
Test Conditions
Pin
Symbol
Min.
Typ.
Unit
Type*
VS1
IIDLE_VS1,2 or
IRX_VS1,2 or
IStartup_PLL_VS1,2 or
1 Li Battery Application (3V)
Max.
VS2
ITX_VS1,2
9.1
Supported voltage
range (every mode
except high power TX
mode)
1 Li battery application
(3V)
PWR_H = GND
17, 18
VVS1, VVS2
2.4
3.6
V
A
9.2
Supported voltage
range (high power TX
mode)
1 Li battery application
(3V)
PWR_H = AVCC
17, 18
VVS1, VVS2
2.7
3.6
V
A
Power supply output
voltage
1 Li battery application
(3V)
VVS1 = VVS2 ≥ 2.6V
VAUX open(1)
IVSOUT ≤ 13.5 mA
(no voltage regulator to
stabilize VVSOUT)
22
VVSOUT
2.4
VVS1
V
B
27
VVSINT
2.4
5.25
V
A
9.3
VVS1 = VVS2 ≥ 2.425V
VAUX open(1)
IVSOUT ≤ 1.5 mA
(no voltage regulator to
stabilize VVSOUT)
9.4
Supply voltage for
microcontroller
interface
9.5
Threshold hysteresis
22
∆VThres
60
80
100
mV
B
9.6
Reset threshold voltage
at pin VSOUT
(N_RESET)
22
VThres_1
2.18
2.3
2.42
V
A
9.7
Reset threshold voltage
at pin VSOUT
(Low_Batt)
22
VThres_2
2.26
2.38
2.5
V
A
9.8
Supply current
OFF mode
17, 18,
22, 27
IS_OFF
2
350
nA
A
VThres_2 – VThres_1
VVS1 = VVS2 ≤ 3.6V
VVSINT = 0V
*) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter
Note:
1. The voltage of VAUX may rise up to 2V. The current IVAUX may not exceed 100 µA.
85
4841D–WIRE–10/07
13. Electrical Characteristics: 1 Li Battery Application (3V) (Continued)
All parameters refer to GND and are valid for Tamb = 25°C, VVS1 = VVS2 = 3.0V. Application according to Figure 2-1 on page 7.
fRF = 315 MHz/345 MHz/433.92 MHz/868.3 MHz/915 MHz unless otherwise specified
No.
Parameters
Test Conditions
Pin
Symbol
Min.
Typ.
Max.
Unit
Type*
312
430
µA
A
260
370
µA
B
225
320
µA
B
VVS1 = VVS2 ≤ 3V
IVSOUT = 0
9.9
Current in IDLE mode
on pin VS1 and VS2
CLK enabled
VVSOUT enabled
17, 18
IIDLE_VS1, 2
CLK disabled
VVSOUT enabled
VVSOUT disabled
9.10
Supply current
IDLE mode
17, 18,
22, 27
IS_IDLE
9.11
Current in RX mode on VVS1 = VVS2 ≤ 3V
pin VS1and VS2
IVSOUT = 0
17, 18
IRX_VS1, 2
9.12
Supply current
RX mode
CLK enabled
VVSOUT enabled
17, 18,
22, 27
IS_RX
9.13
Current during
TStartup_PLL on pin VS1
and VS2
VVS1 = VVS2 ≤ 3V
IVSOUT = 0
17, 18
IStartup_PLL_VS1, 2
9.14
Current in
I IDLE_VS1,2 × T SLEEP + I Startup_PLL_VS1,2 × T Startup_PLL + I RX_VS1,2 × ( T Startup_Sig_Proc + T Bitcheck )
RX polling mode on pin I P = ---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------T Sleep + T Startup_PLL + T Startup_Sig_Proc + T Bitcheck
VS1 and VS2
IS_IDLE = IIDLE_VS1, 2 + IVSINT + IEXT
CLK enabled
VVSOUT enabled
9.15
Supply current
RX polling mode
CLK disabled
VVSOUT enabled
10.5
9.16
9.17
Supply current
TX mode
CLK enabled
VVSOUT enabled
CLK disabled
VVSOUT enabled
mA
A
IS_RX = IRX_VS1, 2 + IVSINT + IEXT
8.8
11.5
mA
C
IS_Poll = IP + IVSINT + IEXT
17, 18,
22, 27
IS_Poll
IS_Poll = IP + IEXT
VVSOUT disabled
VVS1 = VVS2 ≤ 3V
IVSOUT = 0
Pout = 5 dBm/10 dBm
315 MHz/5 dBm
315 MHz/10 dBm
345 MHz/5 dBm
Current in TX mode on 345 MHz/10 dBm
pin VS1 and VS2
433.92 MHz/5 dBm
433.92 MHz/10 dBm
868.3 MHz/5 dBm
868.3 MHz/10 dBm
915 MHz/5 dBm
915 MHz/10 dBm
14
IS_Poll = IP
17, 18
ITX_VS1_VS2
17, 18,
22, 27
IS_TX
10.3
15.7
10.4
15.8
10.5
15.8
11.2
17.3
11.8
19.3
13.4
20.5
13.5
20.6
13.5
20.5
14.5
22.5
15.3
25.1
mA
B
IS_TX = ITX_VS1, 2 + IVSINT + IEXT
IS_TX = ITX_VS1, 2 + IEXT
*) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter
Note:
86
1. The voltage of VAUX may rise up to 2V. The current IVAUX may not exceed 100 µA.
ATA5423/ATA5425/ATA5428/ATA5429
4841D–WIRE–10/07
ATA5423/ATA5425/ATA5428/ATA5429
14. Electrical Characteristics: 2 Li Battery Application (6V)
All parameters refer to GND and are valid for Tamb = 25°C, VVS2 = 6.0V. Application according to Figure 2-3 on page 9
fRF = 315 MHz/345 MHz/433.92 MHz/868.3 MHz/915 MHz unless otherwise specified
No.
Parameters
Test Conditions
10
2 Li Battery Application (6V)
Pin
Symbol
Min.
Typ.
Max.
Unit
Type*
VS2
IIDLE_VS2 or
IRX_VS2 or
IStartup_PLL_VS2 or
ITX_VS2
Supported voltage
range
2 Li battery
application (6V)
17
VVS2
4.4
6.6
V
A
10.2
Power supply output
voltage
2 Li battery
application (6V)
VVS2 ≥ 4.4V
VAUX open(1)
IVSOUT ≤ 13.5 mA
(3.3V regulator mode,
V_REG1, see Figure
5-1 on page 30)
22
VVSOUT
3.0
3.5
V
A
10.3
Supply voltage for
microcontroller
interface
27
VVSINT
2.4
5.25
V
A
10.4
Threshold hysteresis
22
∆VThres
60
80
100
mV
B
10.5
Reset threshold
voltage at pin VSOUT
(N_RESET)
22
VThres_1
2.18
2.3
2.42
V
A
10.6
Reset threshold
voltage at pin VSOUT
(Low_Batt)
22
VThres_2
2.26
2.38
2.5
V
A
10.7
Supply current
OFF mode
17,
22, 27
IS_OFF
10
350
nA
A
17
IIDLE_VS2
410
560
µA
A
CLK disabled
VVSOUT enabled
348
490
µA
B
VVSOUT disabled
309
430
µA
B
10.1
VThres_2 – VThres_1
VVS2 ≤ 6.6V
VVSINT = 0V
VVS2 ≤ 6V
IVSOUT = 0
10.8
Current in IDLE mode
on pin VS2
CLK enabled
VVSOUT enabled
10.9
Supply current IDLE
mode
10.10
Current in RX mode
on pin VS2
IVSOUT = 0
10.11
Supply current
RX mode
CLK enabled
VVSOUT enabled
17,
22, 27
IS_IDLE
17
IRX_VS2
17,
22, 27
IS_RX
IS_IDLE = IIDLE_VS2 + IVSINT + IEXT
10.8
14.5
mA
B
IS_RX = IRX_VS2 + IVSINT + IEXT
*) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter
Note:
1. The voltage of VAUX may rise up to 2 V. The current IVAUX may not exceed 100 µA.
87
4841D–WIRE–10/07
14. Electrical Characteristics: 2 Li Battery Application (6V) (Continued)
All parameters refer to GND and are valid for Tamb = 25°C, VVS2 = 6.0V. Application according to Figure 2-3 on page 9
fRF = 315 MHz/345 MHz/433.92 MHz/868.3 MHz/915 MHz unless otherwise specified
No.
Parameters
Test Conditions
Pin
Symbol
10.12
Current during
TStartup_PLL on pin VS2
IVSOUT = 0
17
IStartup_PLL_VS2
10.13
Current in
RX polling mode on
on pin VS2
Min.
Supply current
RX polling mode
Max.
Unit
Type*
9.1
12
mA
C
I IDLE_VS2 × T SLEEP + I Startup_PLL_VS2 × T Startup_PLL + I RX_VS2 × ( T Startup_Sig_Proc + T Bitcheck )
I P = ---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------T Sleep + T Startup_PLL + T Startup_Sig_Proc + T Bitcheck
CLK enabled
VVSOUT enabled
10.14
Typ.
CLK disabled
VVSOUT enabled
IS_Poll = IP + IVSINT + IEXT
17,
22, 27
IS_Poll
IS_Poll = IP + IEXT
VVSOUT disabled
10.15
Current in TX mode
on pin VS2
IVSOUT = 0
Pout = 5 dBm/10 dBm
315 MHz/5 dBm
315 MHz/10 dBm
345 MHz/5 dBm
345 MHz/10 dBm
433.92 MHz/5 dBm
433.92 MHz/10 dBm
868.3 MHz/5 dBm
868.3 MHz/10 dBm
915 MHz/5 dBm
915 MHz/10 dBm
10.16
Supply current
TX mode
CLK enabled
VVSOUT enabled
CLK disabled
VVSOUT enabled
IS_Poll = IP
17, 19
ITX_VS2
17,
22, 27
IS_TX
10.7
16.2
10.8
16.3
10.9
16.3
11.6
17.8
12.3
20.0
13.9
21.0
14.0
21.2
14.0
21.0
15.0
23.0
16.0
26.0
mA
B
IS_TX = ITX_VS2 + IVSINT + IEXT
IS_TX = ITX_VS2 + IEXT
*) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter
Note:
88
1. The voltage of VAUX may rise up to 2 V. The current IVAUX may not exceed 100 µA.
ATA5423/ATA5425/ATA5428/ATA5429
4841D–WIRE–10/07
ATA5423/ATA5425/ATA5428/ATA5429
15. Electrical Characteristics: Base-station Application (5V)
All parameters refer to GND and are valid for Tamb = 25°C, VVS2 = 5.0V. Application according to Figure 2.2 on page 8
fRF = 315 MHz/345 MHz/433.92 MHz/868.3 MHz/915 MHz unless otherwise specified.
No.
Parameters
Test Conditions
Pin
Symbol
Min.
Typ.
Max.
Unit
Type*
VAUX
11
IIDLE_VS2,VAUX
Base-station Application (5V)
VS2
or IRX_VS2,VAUX
or IStartup_PLL_VS2,VAUX
or ITX_VS2,VAUX
Supported voltage
range
Base-station
application (5V)
11.2
Power supply output
voltage
Base-station
application (5V)
VVS2 = VVAUX
IVSOUT ≤ 13.5 mA
(3.25V regulator
mode, V_REG2, see
Figure 5-1 on page
30)
11.3
Supply voltage for
microcontrollerinterface
11.4
Threshold hysteresis
11.5
11.6
11.1
17,
19, 27
VVS2, VAUX
4.75
5.25
V
A
22
VVSOUT
3.0
3.5
V
A
27
VVSINT
2.4
5.25
V
A
22
∆VThres
60
80
100
mV
B
Reset threshold
voltage at pin VSOUT
(N_RESET)
22
VThres_1
2.18
2.3
2.42
V
A
Reset threshold
voltage at pin VSOUT
(Low_Batt)
22
VThres_2
2.26
2.38
2.5
V
A
444
580
µA
B
VThres_2 – VThres_1
IVSOUT = 0
CLK enabled
VVSOUT enabled
11.7
Current in IDLE mode
on pin VS2 and VAUX
CLK disabled
VVSOUT enabled
17, 19
IIDLE_VS2_VAUX
VVSOUT disabled
17,
19,
22, 27
IS_IDLE
IVSOUT = 0
17, 19
IRX_VS2_VAUX
Supply current in RX
mode
CLK enabled VVSOUT
enabled
17,
19,
22, 27
IS_RX
Current during
TStartup_PLL on pin VS2
and VAUX
IVSOUT = 0
17, 19
11.8
Supply current in
IDLE mode
11.9
Current in RX mode
on pin VS2 and VAUX
11.10
11.11
IStartup_PLL_VS2,
380
500
310
400
IS_IDLE = IIDLE_VS2_VAUX + IVSINT + IEXT
10.8
14.5
mA
B
IS_RX = IRX_VS2_VAUX + IVSINT + IEXT
9.1
12
mA
C
VAUX
*) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter
89
4841D–WIRE–10/07
15. Electrical Characteristics: Base-station Application (5V) (Continued)
All parameters refer to GND and are valid for Tamb = 25°C, VVS2 = 5.0V. Application according to Figure 2.2 on page 8
fRF = 315 MHz/345 MHz/433.92 MHz/868.3 MHz/915 MHz unless otherwise specified.
No.
Parameters
Test Conditions
Pin
Symbol
Min.
Typ.
Max.
Unit
Type*
Current in RX_Polling_Mode on pin VS2 and VAUX
11.12
I IDLE_VS2,VAUX × T SLEEP + I Startup_PLL_VS2,VAUX × T Startup_PLL + I RX_VS2,VAUX × ( T Startup_Sig_Proc + T Bitcheck )
I P = ---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------T Sleep + T Startup_PLL + T Startup_Sig_Proc + T Bitcheck
CLK enabled
VVSOUT enabled
11.13
Supply current in RX
polling mode
CLK disabled
VVSOUT enabled
IS_Poll = IP + IVSINT + IEXT
17,
19,
22, 27
IS_Poll
IS_Poll = IP + IEXT
VVSOUT disabled
11.14
Current in TX mode
on pin VS2 and VAUX
IVSOUT = 0
Pout = 5dBm/10dBm
315 MHz/5dBm
315 MHz/10dBm
345 MHz/5dBm
345 MHz/10dBm
433.92 MHz/5dBm
433.92 MHz/10dBm
868.3 MHz/10dBm
868.3 MHz/10dBm
915 MHz/5dBm
915 MHz/10dBm
11.15
Supply current in
TX mode
CLK enabled
VVSOUT enabled
CLK disabled
VVSOUT enabled
IS_Poll = IP
17, 19
ITX_VS2_VAUX
17,
19,
22, 27
IS_TX
10.7
16.2
10.8
16.3
10.9
16.3
11.6
17.8
12.3
20.0
13.9
21.0
14.0
21.2
14.0
21.0
15.0
23.0
16.0
26.0
mA
B
IS_TX = ITX_VS2_VAUX + IVSINT + IEXT
IS_TX = ITX_VS2_VAUX + IEXT
*) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter
90
ATA5423/ATA5425/ATA5428/ATA5429
4841D–WIRE–10/07
ATA5423/ATA5425/ATA5428/ATA5429
16. Digital Timing Characteristics
All parameters refer to GND and are valid for Tamb = 25°C. VVS1 = VS2 = 3.0V (1 Li battery application (3V)), VVS2 = 6.0V (2 Li battery
application (6V)) and VVS2 = 5.0V (Base-station Application(5V)) unless otherwise specified.
No.
Parameters
12
Basic Clock Cycle of the Digital Circuitry
12.1
Test Conditions
Basic clock cycle
Pin
Symbol
Min.
TDCLK
Typ.
Max.
Unit
Type*
16/fXTO
16/fXTO
µs
A
8
4
2
1
× TDCLK
8
4
2
1
× TDCLK
µs
A
16
8
4
2
× TDCLK
16
8
4
2
× TDCLK
Sleep ×
XSleep ×
1024 ×
TDCLK
Sleep ×
XSleep ×
1024 ×
TDCLK
ms
A
798.5 ×
TDCLK
µs
A
XLIM = 0
BR_Range_0
BR_Range_1
BR_Range_2
BR_Range_3
12.2
Extended basic clock
cycle
XLIM = 1
TXDCLK
BR_Range_0
BR_Range_1
BR_Range_2
BR_Range_3
13
RX Mode/RX Polling Mode
Sleep and XSleep are
defined in control
register 4
13.1
Sleep time
13.2
Start-up PLL RX mode from IDLE mode
13.3
13.4
Start-up signal
processing
Time for bit check
BR_Range_0
BR_Range_1
BR_Range_2
BR_Range_3
Bit-rate range
798.5 ×
TDCLK
TStartup_PLL
TStartup_Sig_Proc
882
498
306
210
× TDCLK
TBit_check
3/fSignal
6/fSignal
9/fSignal
882
498
306
210
× TDCLK
A
Average time during
polling. No RF signal
applied.
fSignal = 1/(2 × tee)
Signal data rate
Manchester
(Lim_min and Lim_max
up to ±50% of tee, see
Figure 9-4 on page 56)
Bit-check time for a valid
input signal fSignal
NBit-check = 0
NBit-check = 3
NBit-check = 6
NBit-check = 9
13.5
TSleep
BR_Range =
BR_Range0
BR_Range1
BR_Range2
BR_Range3
BR_Range
1.0
2.0
4.0
8.0
1/fSignal
3.5/fSignal
6.5/fSignal
9.5/fSignal
2.5
5.0
10.0
20.0
ms
C
Kbit/s
A
*) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter
91
4841D–WIRE–10/07
16. Digital Timing Characteristics (Continued)
All parameters refer to GND and are valid for Tamb = 25°C. VVS1 = VS2 = 3.0V (1 Li battery application (3V)), VVS2 = 6.0V (2 Li battery
application (6V)) and VVS2 = 5.0V (Base-station Application(5V)) unless otherwise specified.
No.
Parameters
Test Conditions
Pin
Symbol
Min.
31
TDATA_min
10 ×
TXDCLK
TDATA
200
100
50
25
Typ.
Max.
Unit
Type*
µs
A
500
250
125
62.5
µs
B
331.5
× TDCLK
µs
A
XLIM = 0
13.6
Minimum time period
between edges at pin
SDO_TMDO in RX
transparent mode
BR_Range_0
BR_Range_1
BR_Range_2
BR_Range_3
XLIM = 1
BR_Range_0
BR_Range_1
BR_Range_2
BR_Range_3
13.7
14
14.1
15
Edge-to-edge time
period of the data signal
for full sensitivity in RX
mode
BR_Range_0
BR_Range_1
BR_Range_2
BR_Range_3
TX Mode
Start-up time
From IDLE mode
331.5
× TDCLK
TStartup
Configuration of the Transceiver with 4-wire Serial Interface
33, 35
TCS_setup
1.5 ×
TDCLK
µs
A
33
TCycle
2
µs
A
SDI_TMDI set-up time
to rising edge of SCK
32, 33
TSetup
250
ns
C
15.4
SDI_TMDI hold time
from rising edge of SCK
32, 33
THold
250
ns
C
15.5
SDO_TMDO enable
time from rising edge of
CS
31, 35
TOut_enable
250
ns
C
15.6
SDO_TMDO output
delay from falling edge
of SCK
31, 35
TOut_delay
250
ns
C
15.7
SDO_TMDO disable
time from falling edge of
CS
31, 33
TOut_disable
250
ns
C
15.8
CS disable time period
35
TCS_disable
1.5 ×
TDCLK
µs
A
15.9
Time period SCK low to
CS high
33, 35
TSCK_setup1
250
ns
C
15.10
Time period SCK low to
CS low
33, 35
TSCK_setup2
250
ns
C
15.11
Time period CS low to
SCK high
33, 35
TSCK_hold
250
ns
C
15.1
CS set-up time to rising
edge of SCK
15.2
SCK cycle time
15.3
CL = 10 pF
*) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter
92
ATA5423/ATA5425/ATA5428/ATA5429
4841D–WIRE–10/07
ATA5423/ATA5425/ATA5428/ATA5429
16. Digital Timing Characteristics (Continued)
All parameters refer to GND and are valid for Tamb = 25°C. VVS1 = VS2 = 3.0V (1 Li battery application (3V)), VVS2 = 6.0V (2 Li battery
application (6V)) and VVS2 = 5.0V (Base-station Application(5V)) unless otherwise specified.
No.
Parameters
Test Conditions
16
Start Time Push Button Tn and PWR_ON
Timing of Wake-up via PWR_ON or Tn
Pin
Symbol
Min.
Typ.
Max.
Unit
0.3
0.8
ms
2 Li battery application
(6V)
C1 = C4 = 68 nF
C2 = C3 = 2.2 µF
C5 = 10 nF
0.45
1.3
ms
Base-station Application
(5V)
C1 = C3 = C4 = 68 nF
C2 = C12 = 2.2 µF
C5 = 10 nF
0.45
1.3
ms
Type*
From OFF mode to IDLE
mode, applications
according to Figure 2-1
on page 7, Figure 2.2 on
page 8 and Figure 2-3
on page 9
XTAL:
Cm < 14 fF (typ. 5 fF)
C0 < 2.2 pF (typ. 1.8 pF)
Rm ≤120Ω (typ. 15Ω)
16.1
PWR_ON high to
positive edge on pin
IRQ (see Figure 7-4 on
page 46)
1 Li battery application
(3V)
C1 = C2 = 68 nF
C3 = C4 = 68 nF
C5 = 10 nF
29, 40 TPWR_ON_IRQ_1
B
*) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter
93
4841D–WIRE–10/07
16. Digital Timing Characteristics (Continued)
All parameters refer to GND and are valid for Tamb = 25°C. VVS1 = VS2 = 3.0V (1 Li battery application (3V)), VVS2 = 6.0V (2 Li battery
application (6V)) and VVS2 = 5.0V (Base-station Application(5V)) unless otherwise specified.
No.
Parameters
Test Conditions
16.2
PWR_ON high to
positive edge on pin
Every mode except OFF
IRQ (see Figure 7-4 on mode
page 46)
Pin
Symbol
Min.
Typ.
Max.
Unit
Type*
2×
TDCLK
µs
A
0.3
0.8
ms
2 Li battery application
(6V)
C1 = C4 = 68 nF
C2 = C3 = 2.2 µF
C5 = 10 nF
0.45
1.3
ms
Base-station Application
(5V)
C1 = C3 = C4 = 68 nF
C2 = C12 = 2.2 µF
C5 = 10 nF
0.45
1.3
ms
8195
× TDCLK
µs
29, 40 TPWR_ON_IRQ_2
From OFF mode to IDLE
mode, applications
according to Figure 2-1
on page 7, Figure 2.2 on
page 8 and Figure 2-3
on page 9
XTAL:
Cm < 14 fF (typ 5 fF)
C0 < 2.2 pF (typ 1.8 pF)
Rm ≤ 120Ω (typ 15Ω)
16.3
16.4
1 Li battery application
(3V)
Tn low to positive edge
C1 = C2 = 68 nF
on pin IRQ (see Figure
C3 = C4 = 68 nF
7-2 on page 44)
C5 = 10 nF
Push button debounce
time
29, 41,
42, 43,
44, 45
29, 41,
Every mode except OFF
42, 43,
mode
44, 45
TTn_IRQ
TDebounce
8195
× TDCLK
B
A
*) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter
94
ATA5423/ATA5425/ATA5428/ATA5429
4841D–WIRE–10/07
ATA5423/ATA5425/ATA5428/ATA5429
17. Digital Port Characteristics
All parameters refer to GND and are valid for Tamb = –40°C to +85 °C, VVS1 = VS2 = 2.4V to 3.6V (1 Li battery application (3V)) and
VVS2 = 4.4V to 6.6 V (2 Li battery application (6V)) and VVS2 = 4.75V to 5.25V (Base-station Application (5V)). Typical values at
VVS1 = VVS2 = 3V and Tamb = 25°C unless otherwise specified.
No.
Parameters
17
Digital Ports
17.1
17.2
17.3
Test Conditions
Pin
Symbol
VVSINT = 2.4V to 5.25V
35
VIl
High level input voltage VVSINT = 2.4V to 5.25V
35
VIh
SCK input
Low level input voltage
VVSINT = 2.4V to 5.25V
33
VIl
High level input voltage VVSINT = 2.4V to 5.25V
33
VIh
SDI_TMDI input
Low level input voltage
VVSINT = 2.4V to 5.25V
32
VIl
High level input voltage VVSINT = 2.4V to 5.25V
32
VIh
CS input
Low level input voltage
Min.
Max.
Unit
Type*
0.2 ×
VVSINT
V
A
VVSINT
V
A
0.2 ×
VVSINT
V
A
VVSINT
V
A
0.2 ×
VVSINT
V
A
0.8 ×
VVSINT
VVSINT
V
A
0.8 ×
VVSINT
0.8 ×
VVSINT
Typ.
17.4
TEST1 input
TEST1 input must
always be directly
connected to GND
20
0
0
V
17.5
TEST2 input
TEST2 input must
always be direct
connected to GND
23
0
0
V
PWR_ON input
Low level input voltage
Internal pull-down with
series connection of
40 kΩ ±20% resistor
and diode
40
VIl
0.4
V
A
High level input
voltage(1)
Internal pull-down with
series connection of
40 kΩ ±20% resistor
and diode
40
VIh
V
A
Tn input
Low level input voltage
Internal pull-up resistor
of 50 kΩ ±20%
41, 42,
43, 44,
45
VIl
V
A
High level input
voltage(1)
Internal pull-up resistor
of 50 kΩ ±20%
41, 42,
43, 44,
45
VIh
V
A
6
VIl
0.25
V
A
17.6
17.7
433_N868 input
Low level input voltage
17.8
Input current low
6
IIl
High level input voltage
6
VIh
Input current high
6
IIh
0.8
× VVS2
0.2
× VVS2
× VVS2
–0.5V
1.7
–5
µA
A
AVCC
V
A
1
µA
A
*) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter
Note:
1. If a logic high level is applied to this pin, a minimum serial impedance of 100Ω must be ensured for proper operation over full
temperature range.
95
4841D–WIRE–10/07
17. Digital Port Characteristics (Continued)
All parameters refer to GND and are valid for Tamb = –40°C to +85 °C, VVS1 = VS2 = 2.4V to 3.6V (1 Li battery application (3V)) and
VVS2 = 4.4V to 6.6 V (2 Li battery application (6V)) and VVS2 = 4.75V to 5.25V (Base-station Application (5V)). Typical values at
VVS1 = VVS2 = 3V and Tamb = 25°C unless otherwise specified.
No.
17.9
Parameters
Pin
Symbol
PWR_H input
Low level input voltage
Test Conditions
9
Input current low
High level input voltage
Input current high
17.10
17.11
17.12
17.13
17.14
17.15
Max.
Unit
Type*
VIl
0.25
V
A
9
IIl
–5
µA
A
9
VIh
AVCC
V
A
1
µA
A
0.4
V
B
V
B
V
B
V
B
V
B
V
B
V
B
V
B
V
B
V
B
V
B
9
IIh
SDO_TMDO output
Saturation voltage low
VVSINT = 2.4V to 5.25V
ISDO_TMDO = 250 µA
31
Vol
Saturation voltage high
VVSINT = 2.4V to 5.25V
ISDO_TMDO = –250 µA
31
Voh
IRQ output
Saturation voltage low
VVSINT = 2.4V to 5.25V
IIRQ = 250 µA
29
Vol
Saturation voltage high
VVSINT = 2.4V to 5.25V
IIRQ = –250 µA
29
Voh
CLK output
Saturation voltage low
VVSINT = 2.4V to 5.25V
ICLK = 100 µA
internal series resistor
of 1 kΩ for spurious
emission reduction in
PLL
30
Vol
VVSINT = 2.4V to 5.25V
ICLK = –100 µA
internal series resistor
Saturation voltage high
of 1 kΩ for spurious
emission reduction in
PLL
30
Voh
N_RESET output
Saturation voltage low
VVSINT = 2.4V to 5.25V
IN_RESET = 250 µA
28
Vol
Saturation voltage high
VVSINT = 2.4V to 5.25V
IN_RESET = –250 µA
28
Voh
RX_ACTIVE output
Saturation voltage low
VVSINT = 2.4V to 5.25V
IRX_ACTIVE = 25 µA
46
Vol
Saturation voltage high
VVSINT = 2.4V to 5.25V
IRX_ACTIVE = –1500 µA
46
Voh
DEM_OUT output
Saturation voltage low
Open drain output
IDEM_OUT = 250 µA
34
Vol
Min.
Typ.
1.7
0.15
VVSINT –
0.4
VVSINT –
0.15
0.15
VVSINT –
0.4
VVSINT –
0.15
0.15
VVSINT –
0.4
0.4
VVSINT –
0.15
0.25
VAVCC
–0.5
0.4
VVSINT –
0.15
0.15
VVSINT –
0.4
0.4
0.4
VAVCC
–0.15
0.15
0.4
*) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter
Note:
96
1. If a logic high level is applied to this pin, a minimum serial impedance of 100Ω must be ensured for proper operation over full
temperature range.
ATA5423/ATA5425/ATA5428/ATA5429
4841D–WIRE–10/07
ATA5423/ATA5425/ATA5428/ATA5429
18. Ordering Information
Extended Type Number
Package
Remarks
Delivery
ATA5423-PLQW
QFN48
7 mm × 7 mm
Taped and reeled + Dry pack
ATA5425-PLQW
QFN48
7 mm × 7 mm
Taped and reeled + Dry pack
ATA5428-PLQW
QFN48
7 mm × 7 mm
Taped and reeled + Dry pack
ATA5429-PLQW
QFN48
7 mm × 7 mm
Taped and reeled + Dry pack
ATA5423-PLSW
QFN48
7 mm × 7 mm
Tubes + Dry pack
ATA5425-PLSW
QFN48
7 mm × 7 mm
Tubes + Dry pack
ATA5428-PLSW
QFN48
7 mm × 7 mm
Tubes + Dry pack
ATA5429-PLSW
Note:
W = RoHS compliant
QFN48
7 mm × 7 mm
Tubes + Dry pack
19. Package Information
Package: QFN 48 - 7 x 7
Exposed pad 5.1 x 5.1
Dimensions in mm
Not indicated tolerances ± 0.05
7
1 max.
5.5
+0
0.05-0.05
5.1
37
48
48
36
1
1
technical drawings
according to DIN
specifications
25
12
24
0.4±0.1
0.23
12
13
0.5 nom.
Drawing-No.: 6.543-5089.02-4
Issue: 1; 14.01.03
97
4841D–WIRE–10/07
20. Revision History
Please note that the following page numbers referred to in this section refer to the specific revision
mentioned, not to this document.
98
Revision No.
History
4841D-WIRE-10/07
• Put datasheet in a new template
4841C-WIRE-05/06
•
•
•
•
Put datasheet in a new template
kBaud replaced through Kbit/s
Baud replaced through bit
Table 9-6 “Interrupt Handling” on page 65 changed
ATA5423/ATA5425/ATA5428/ATA5429
4841D–WIRE–10/07
ATA5423/ATA5425/ATA5428/ATA5429
21. Table of Contents
Features ..................................................................................................... 1
Applications .............................................................................................. 2
Benefits...................................................................................................... 2
1
General Description ................................................................................. 3
2
Application Circuits ................................................................................. 7
3
RF Transceiver ....................................................................................... 10
4
XTO .......................................................................................................... 25
5
Power Supply ......................................................................................... 30
6
Microcontroller Interface ....................................................................... 36
7
Digital Control Logic .............................................................................. 36
8
Transceiver Configuration .................................................................... 49
9
Operation Modes .................................................................................... 52
10 Absolute Maximum Ratings .................................................................. 66
11 Thermal Resistance ............................................................................... 66
12 Electrical Characteristics: General ...................................................... 67
13 Electrical Characteristics: 1 Li Battery Application (3V) .................... 85
14 Electrical Characteristics: 2 Li Battery Application (6V) .................... 87
15 Electrical Characteristics: Base-station Application (5V) .................. 89
16 Digital Timing Characteristics .............................................................. 91
17 Digital Port Characteristics ................................................................... 95
18 Ordering Information ............................................................................. 97
19 Package Information ............................................................................. 97
20 Revision History ..................................................................................... 98
99
4841D–WIRE–10/07
Headquarters
International
Atmel Corporation
2325 Orchard Parkway
San Jose, CA 95131
USA
Tel: 1(408) 441-0311
Fax: 1(408) 487-2600
Atmel Asia
Room 1219
Chinachem Golden Plaza
77 Mody Road Tsimshatsui
East Kowloon
Hong Kong
Tel: (852) 2721-9778
Fax: (852) 2722-1369
Atmel Europe
Le Krebs
8, Rue Jean-Pierre Timbaud
BP 309
78054
Saint-Quentin-en-Yvelines Cedex
France
Tel: (33) 1-30-60-70-00
Fax: (33) 1-30-60-71-11
Atmel Japan
9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
Japan
Tel: (81) 3-3523-3551
Fax: (81) 3-3523-7581
Technical Support
[email protected]
Sales Contact
www.atmel.com/contacts
Product Contact
Web Site
www.atmel.com
Literature Requests
www.atmel.com/literature
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any
intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY
WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF
THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no
representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications
and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided
otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use
as components in applications intended to support or sustain life.
© 2007 Atmel Corporation. All rights reserved. Atmel ®, logo and combinations thereof, and others are registered trademarks or trademarks of
Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.
4841D–WIRE–10/07