LC5222D/25D and LC5222S/25S Off-Line DC / DC LED Driver ICs Features and Benefits Description • Buck and buck-boost topology; selectable by peripheral circuit structure • Built-in fixed reference voltage limiting constant current control; high precision regulator improves current precision and simplifies setting of current level • Sleep function, with latch mode; input high, 3 V or more, on REF pin turns off IC output to LEDs • Enable function; input low on REF pin toggles IC output to LEDs • High input voltage; up to 250 V or 450 V, depending on product • Output Current: 0.5A • Built-in constant current control; PWM method, output current adjustable by the voltage input on the REF pin • External adjustable PWM dimming control • Protection features: ▫ Open protection (OPP) with latched shutdown; protects IC when a free-wheeling diode is open ▫ Undervoltage lockout (UVLO) ▫ Overcurrent protection (OCP) with latched shutdown; variable OCP threshold linked to REF pin voltage ▫ Thermal shutdown (TSD) with auto restart LC5220 series is a non-isolating, simple and efficient LED driver. The high voltage capability allows direct connection to a wide range of supply voltages ranging from 25 to 400 V (recommended). The LC5220 uses constant current mode to drive LEDs. and buck and buck-boost voltage converters can be configured. Packages • LED lighting fixtures • LED light bulbs SOP8 A power MOSFET and controller IC are incorporated in one package. Because few external parts are required, the LC5220 is ideal for use in small-size LED light bulbs. Various control requirements can be supported through the REF pin, including peak current control, output on/off, and sleep mode enable. Moreover, there is a protection circuit for freewheeling diode open, protection for a buck-boost voltage converter open LED load, and a variable overcurrent protection function. These features improve safety for both the LC5220 and the LEDs. Applications DIP8 Not to scale Typical Application VIN Line Filter AC Input CIN REG VBB R1 R2 LC5220 C1 C2 D1 REF PWM CPWM OUT GND C3 VLED L1 SEN RS An example of a buck voltage converter application circuit LC5222D/25D_22S/25S-DS SANKEN ELECTRIC CO., LTD. August 8, 2012 LC5222D/25D and LC5222S/25S Off-Line DC / DC LED Driver ICs Selection Guide Part Number Package LC5222D Maximum Input Voltage VBB(max) (V) Output MOSFET RDS(ON)(max) (Ω) DIP8 LC5225D LC5222S SOP8 LC5225S 250 2.2 450 6 250 2.2 450 6 The polarity value for current specifies a sink as "+," and a source as “−,” referencing the IC. Absolute Maximum Ratings Unless specifically noted, TA is 25°C Characteristic Main Power Supply Voltage Output Breakdown Voltage Output Current2 Symbol Notes LC5222D/S VBB LC5225D/S LC5222D/S VO(BR) Rating Unit 6–8 (7 – 8) 250 V 450 V 250 V 5–4 (5, 6 – 4) LC5225D/S IO Pins1 Pulse width ≥ 1 μs 450 V 5–4 (5, 6 – 4) 0.5 A PWM Pin Voltage3 VPWM 2–8 −0.3 to VZ V REF Pin Input Voltage3 VREF 3–8 −0.3 to VZ V SEN Pin Voltage VSEN 4–8 −0.3 to 4.0 V 0.85 W 1.73 W °C Allowable Power Dissipation4,5 Pulse width ≥ 1 μs LC5222S LC5225S PD On Sanken evaluation PCB LC5222D LC5225D ― Operating Ambient Temperature TA ― −40 to 105 Storage Temperature Tstg ― −40 to 150 °C Junction Temperature TJ ― 150 °C 1Where the pin numbers differ between the DIP8 and the SOP8 packages, the SOP8 pin number is written in parentheses. output current value may be restricted based on duty cycle, ambient air temperature, or heat dissipation conditions. In any case, please be sure to keep from exceeding the junction temperature, TJ. 3Zener diodes are built-in between the PWM pin and GND, and between the REF pin and GND. V is the breakdown voltage of these internal Zener Z diodes, and VZ = 6.3 V (typ). In addition, the maximum sink current is 1 mA. 4Allowable loss, P , is dependent on the circuit layout of the PCB to be used. D 5Please refer to the Ambient Temperature versus Power Dissipation Curve. 2The Ambient Temperature versus Power Dissipation 2.0 On Sanken evaluation PCB Maximum Allowable Power Dissipation, PD (W) PD = 1.73 W 1.5 R DIP 1.0 PD = 0.85 W θJ -A 72 °C /W Rθ J-A SOP 0.5 = =1 47 °C/ W 0 0 25 50 75 100 125 150 Ambient Temperature, TA (°C) LC5222D/25D_22S/25S-DS SANKEN ELECTRIC CO., LTD. 2 August 8, 2012 LC5222D/25D and LC5222S/25S Off-Line DC / DC LED Driver ICs Recommended Operating Conditions Characteristic Symbol Test Conditions LC5222D/S Power Supply Voltage VBB LC5225D/S Average Output Current REF Pin Input Voltage Case Temperature Minimum input voltage depends on LED output voltage and converter topology. IO(AVG) VREF TC Normal operation Measured at the center of the branded side, TJ ≤ 150°C. Pins* Min. Max. Unit 25 200 V 25 400 V 5–4 (5, 6 – 4) ― 0.4 A 3–8 0.2 2.5 V – ― 105 °C 6–8 (7 – 8) Note: Recommended Operating Conditions means the operation conditions to maintain normal functions shown in the Electrical Characteristics table. *Where the pin numbers differ between the DIP8 and the SOP8 packages, the SOP8 pin number is written in parentheses. LC5222D/25D_22S/25S-DS SANKEN ELECTRIC CO., LTD. 3 August 8, 2012 LC5222D/25D and LC5222S/25S Off-Line DC / DC LED Driver ICs Electrical Characteristics Unless specifically noted, TA is 25°C, VBB = 140 V Characteristic Symbol Test Conditions Min. Typ. Max. Unit ― 1 1.5 mA ― 2.5 4.0 mA IBBS Output off 6–8 (7 – 8) IBB Normal operation 6–8 (7 – 8) Power Supply Current Output MOSFET Breakdown Voltage V(BR)DSS Output MOSFET On-Resistance RDS(ON) Body Diode Forward Voltage Pins1 Vf LC5222D/S ID = 1 mA LC5225D/S LC5222D/S ID = 0.5 A LC5225D/S ID = 0.5 A LC5222D/S If = 0.5 A LC5225D/S If = 0.5 A 5–4 (5, 6 – 4) 250 ― ― V 450 ― ― V 5–4 (5, 6 – 4) ― 1.2 2.2 Ω ― 3.5 6 Ω ― 0.8 1.0 V ― 0.8 0.9 V 4−5 (4 – 5, 6) UVLO Threshold (Turn on) VUVLO(ON) VBB pin voltage 6–8 (7 – 8) ― 14 ― V UVLO Threshold (Turn off) VUVLO(OFF) VBB pin voltage 6–8 (7 – 8) ― 12 ― V 1−8 9.6 10 10.4 V REG Pin Output Voltage VREG IREG = 0 mA REG Pin Output Current IREG VREG = 9 V 1−8 −2 ― ― mA Enable Output Threshold Voltage VENB REF pin voltage 3−8 ― 0.15 0.19 V Sleep Mode Threshold Voltage VSLP REF pin voltage 3−8 2.85 3.0 ― V REF Pin Current IREF 3−8 −10 ― 10 μA Current Control Detection Voltage2 VSEN 4−8 0.4 × VREF − 0.03 0.4 × VREF 0.4 × VREF + 0.03 V 0.77 0.8 0.83 V ― 0.4 × VREF + 0.7 ― V VREF = 0.2 to 2.0 V VREF = 2.0 to 3.0 V VREF = 0.2 to 2.0 V OCP Detection Voltage2 VOCP 4−8 ― 1.5 ― V SEN Pin Current ISEN 4−8 −10 ― 10 μA PWM Pin Low Voltage VPWM(L) 2−8 ― 2 ― V PWM Pin High Voltage VPWM(H) 2−8 ― 3 ― V PWM Pin Output Current IPWM 2−8 ― −20 ― μA PWM Blanking Time tBLK(P) ― ― 0.3 ― μs OCP Blanking Time tBLK(O) VREF = 2.0 to 3.0 V PWM Operation Frequency fPWM Duty cycle = 50% ― ― 0.2 ― μs 2−8 ― ― 200 kHz ― ― 17 ― μs PWM Off Time toff CPWM = 100 pF Output MOSFET Rise Time tr IO = 0.4 A 5–4 (5, 6 – 4) ― 25 ― ns Output MOSFET Fall Time tf IO = 0.4 A 5–4 (5, 6 – 4) ― 50 ― ns Thermal Shutdown Threshold3 TTSD ― ― 150 ― °C Thermal Shutdown Hysteresis3 TTSD(HYS) ― ― 55 ― °C 1Where the pin numbers differ between the DIP8 and the SOP8 packages, the SOP8 pin number is written in parentheses. REF pin has different functions, depending on the voltage. Please refer to REF Pin Voltage Characteristics section. 3Chip temperature of control IC, T . J 2The LC5222D/25D_22S/25S-DS SANKEN ELECTRIC CO., LTD. 4 August 8, 2012 LC5222D/25D and LC5222S/25S Off-Line DC / DC LED Driver ICs Internal Reference Voltage (V) REF Pin Voltage Characteristics OCP_REF _OS VOCR + VCCR R= C VO 0.8 VOCR_OS CC_REF .4 ×0 Ref V = CR VC 0 0 1.0 0.15 2.0 3.0 REF Pin Input VoltageVREF (V) On (Enable) Out Latch (Sleep) Off (Disable) Function Conditions Internal PWM reference voltage, VCCR • When VREF < 2 V, VCCR = 0.4 × VREF (V) (VCCR is proportional to VREF) • When VREF > 2 V, VCCR = 0.8 V OCP reference voltage, VOCR VOCR is offset from VCCR by VOCP_OS ; VOCR_OS = 0.7 V (typ); VOCR has negative temperature characteristics Enable function Enable mode is entered when VREF > VENB ; Enable mode is not latched, and the IC stops operating when VREF falls below VENB; VENB = 0.15 V (typ) Sleep function Sleep mode is entered when VREF > VSLP , turning off the output; VENB = 3.0 V (typ); Sleep mode is latched, and the latch is released when VBB falls below VUVLO(OFF); VUVLO(OFF) = 12 V (typ) LC5222D/25D_22S/25S-DS SANKEN ELECTRIC CO., LTD. 5 August 8, 2012 LC5222D/25D and LC5222S/25S Off-Line DC / DC LED Driver ICs Functional Block Diagram VBB 6(7) LC5220 Control Part 1 TSD Band Gap Reference PWM 2 PWM _IN CC REF 3 Reference Control CC_REF Current Detect OCP_REF SEN_IN OC UVLO PWM Control OCP Blanking REG Regulator UVLO TSD PWM OCP OPP SLEEP ENABLE Output Control Logic 5(5,6) OUT OPP Logic Gate Driver 4 8 GND SEN Pin numbers in parentheses refer to the SOP8 package Pin List Table Name Pin-out Diagrams REG 1 8 GND PWM 2 REF 3 6 VBB SEN 4 5 OUT DIP8 (LC5220D series) REG 1 8 GND PWM 2 7 VBB Number Function DIP8 SOP8 REG 1 1 Internal regulator supply, provides current to internal and external circuits; connect a 0.1 μF bypass capacitor between this pin and GND. PWM 2 2 Input for PWM control: to use internal PWM, connect a capacitor for setting off-time; to use external PWM, connect to PWM signal source. REF 3 3 Reference voltage input: sets peak output current of OUT pin (internal power MOSFET) for internal PWM control, enables toggling output of OUT pin (Enable function), and enables latched shutdown of output (Sleep function) SEN 4 4 Output current detection: detects peak output current for internal PWM control, and detects overcurrent for OCP; connect to current detection resistor. OUT 5 5, 6 6 7 Supply voltage, provides power to internal circuits through internal regulator. Drain of internal power MOSFET. REF 3 6 OUT VBB SEN 4 5 OUT GND 8 8 Ground pin. ― 7 ― LC5220D DIP8 pin removed to increase creepage distance between high voltage pin and low voltage pin. Note: Apply user’s criteria for creepage distance when using LC5220S SOP8. SOP8 (LC5220S series) LC5222D/25D_22S/25S-DS SANKEN ELECTRIC CO., LTD. 6 August 8, 2012 LC5222D/25D and LC5222S/25S Off-Line DC / DC LED Driver ICs Reference Components List of a Buck Configuration Circuit (refer to Typical Application diagram); Input voltage: 100 VAC, LED output voltage: 15 V, LED peak output current : 0.3 A Name Type Value Description LED LED ― L1 Inductor 1 mH / 1 A User-defined D1 Fast recovery rectifier diode RD2A CIN Capacitor Up to 4.7 μF / 450 V C1 Capacitor 0.1 μF / 25 V Internal regulator stabilizing capacitor C2 Capacitor 1000 pF (to 0.1 μF) / 25 V REF pin voltage stabilizing capacitor Choke coil for smoothing current Free-wheeling diode for recirculation Main supply source filtering capacitor; 1 nF or higher can be used C3 Capacitor 0.1 μF / 250 V Smoothing capacitor for reducing LED ripple current (Optional) CPWM Capacitor 100 pF / 25 V PWM off-time setting capacitor (internal PWM control) R1 Resistor 620 kΩ / 1/8 W Resistor for setting peak output current on OUT pin R2 Resistor 51 kΩ / 1/8 W Resistor for setting peak output current on OUT pin RS Resistor 1.0 Ω / 1 W Resistor for output current detection Note: Because no specific application or noise factor is considered in the typical application circuit diagrammed, it is required that the user takes into consideration such issues during designing. Moreover, the above values are only reference examples. It is required to change components according to the LED load and other conditions which are actually used. LC5222D/25D_22S/25S-DS SANKEN ELECTRIC CO., LTD. 7 August 8, 2012 LC5222D/25D and LC5222S/25S Off-Line DC / DC LED Driver ICs Package Outline Drawing, DIP8 9.4 ±0.3 5 1 4 6.5 ±0.2 8 1.0 +0.3 -0.05 +0.3 1.52 -0.05 3.3 ±0.2 7.5 ±0.5 4.2 ±0.3 3.4 ±0.1 (7.6 TYP) 0.2 5 + 0. - 0.01 5 ０～１５° ０～１５° 2.54 TYP 0.89 TYP 0.5 ±0.1 Unit： mm 8 LC522x SK YMD D XXXX 1 Part Number Lot Number Y is the last digit of the year (0 to 9) M is the month (1 to 9, O, N, or D) D is a period of days (1 to 3): 1 – 1st to 10th 2 – 11th to 20th 3 – 21st to 31st Sanken Control Number Pb-free. Device composition compliant with the RoHS directive. LC5222D/25D_22S/25S-DS SANKEN ELECTRIC CO., LTD. 8 August 8, 2012 LC5222D/25D and LC5222S/25S Off-Line DC / DC LED Driver ICs Package Outline Drawing, SOP8 5.2 ±0.3 1 0.695 TYP 6.2 ±0.3 5 4.4 ±0.2 8 4 5.25 ±0.3 0.05 ±0.05 1.27±0.05 0.10 0.12 M +0.1 0.15 –0.05 1.5 ±0.1 0 ~ 10° 0.4±0.2 0.4±0.1 Unit： mm 8 LC522x SK YMD Part Number Lot Number Y is the last digit of the year (0 to 9) M is the month (1 to 9, O, N, or D) D is a period of days (1 to 3): 1 – 1st to 10th 2 – 11th to 20th 3 – 21st to 31st XXXX 1 Sanken Control Number Pb-free. Device composition compliant with the RoHS directive. LC5222D/25D_22S/25S-DS SANKEN ELECTRIC CO., LTD. 9 August 8, 2012 LC5222D/25D and LC5222S/25S Off-Line DC / DC LED Driver ICs Because reliability can be affected adversely by improper storage environments and handling methods, please observe the following cautions. Cautions for Storage • Ensure that storage conditions comply with the standard temperature (5°C to 35°C) and the standard relative humidity (around 40% to 75%); avoid storage locations that experience extreme changes in temperature or humidity. • Avoid locations where dust or harmful gases are present and avoid direct sunlight. • Reinspect for rust on leads and solderability of the products that have been stored for a long time. Cautions for Testing and Handling When tests are carried out during inspection testing and other standard test periods, protect the products from power surges from the testing device, shorts between the product pins, and wrong connections. Ensure all test parameters are within the ratings specified by Sanken for the products. Remarks About Using Silicone Grease with a Heatsink • When silicone grease is used in mounting the products on a heatsink, it shall be applied evenly and thinly. If more silicone grease than required is applied, it may produce excess stress. • Volatile-type silicone greases may crack after long periods of time, resulting in reduced heat radiation effect. Silicone greases with low consistency (hard grease) may cause cracks in the mold resin when screwing the products to a heatsink. Our recommended silicone greases for heat radiation purposes, which will not cause any adverse effect on the product life, are indicated below: Type Suppliers G746 Shin-Etsu Chemical Co., Ltd. YG6260 Momentive Performance Materials Inc. SC102 Dow Corning Toray Co., Ltd. LC5222D/25D_22S/25S-DS Soldering • When soldering the products, please be sure to minimize the working time, within the following limits: ▫ DIP8 Flow soldering: 260±5°C 10±1 s (2 times) Soldering iron: 380±10°C 3.5±0.5 s (1 time) Soldering should be at a distance of at least 1.5 mm from the body of the products. ▫ SOP8: Reflow soldering: 180°C 90±30 s for preheating, 250°C 10±1 s (260°C peak, 2 times) for solder heating Soldering iron: 380±10°C 3.5±0.5 s (1 time) Note: Flow soldering must not be used. Electrostatic Discharge • When handling the products, the operator must be grounded. Grounded wrist straps worn should have at least 1 MΩ of resistance from the operator to ground to prevent shock hazard, and it should be placed near the operator. • Workbenches where the products are handled should be grounded and be provided with conductive table and floor mats. • When using measuring equipment such as a curve tracer, the equipment should be grounded. • When soldering the products, the head of soldering irons or the solder bath must be grounded in order to prevent leak voltages generated by them from being applied to the products. • The products should always be stored and transported in Sanken shipping containers or conductive containers, or be wrapped in aluminum foil. SANKEN ELECTRIC CO., LTD. 10 August 8, 2012 LC5222D/25D and LC5222S/25S Off-Line DC / DC LED Driver ICs • The contents in this document are subject to changes, for improvement and other purposes, without notice. Make sure that this is the latest revision of the document before use. • Application and operation examples described in this document are quoted for the sole purpose of reference for the use of the products herein and Sanken can assume no responsibility for any infringement of industrial property rights, intellectual property rights or any other rights of Sanken or any third party which may result from its use. • Although Sanken undertakes to enhance the quality and reliability of its products, the occurrence of failure and defect of semiconductor products at a certain rate is inevitable. Users of Sanken products are requested to take, at their own risk, preventative measures including safety design of the equipment or systems against any possible injury, death, fires or damages to the society due to device failure or malfunction. • Sanken products listed in this document are designed and intended for the use as components in general purpose electronic equipment or apparatus (home appliances, office equipment, telecommunication equipment, measuring equipment, etc.). When considering the use of Sanken products in the applications where higher reliability is required (transportation equipment and its control systems, traffic signal control systems or equipment, fire/crime alarm systems, various safety devices, etc.), and whenever long life expectancy is required even in general purpose electronic equipment or apparatus, please contact your nearest Sanken sales representative to discuss, prior to the use of the products herein. The use of Sanken products without the written consent of Sanken in the applications where extremely high reliability is required (aerospace equipment, nuclear power control systems, life support systems, etc.) is strictly prohibited. • In the case that you use Sanken products or design your products by using Sanken products, the reliability largely depends on the degree of derating to be made to the rated values. Derating may be interpreted as a case that an operation range is set by derating the load from each rated value or surge voltage or noise is considered for derating in order to assure or improve the reliability. In general, derating factors include electric stresses such as electric voltage, electric current, electric power etc., environmental stresses such as ambient temperature, humidity etc. and thermal stress caused due to self-heating of semiconductor products. For these stresses, instantaneous values, maximum values and minimum values must be taken into consideration. In addition, it should be noted that since power devices or IC's including power devices have large self-heating value, the degree of derating of junction temperature affects the reliability significantly. • When using the products specified herein by either (i) combining other products or materials therewith or (ii) physically, chemically or otherwise processing or treating the products, please duly consider all possible risks that may result from all such uses in advance and proceed therewith at your own responsibility. • Anti radioactive ray design is not considered for the products listed herein. • Sanken assumes no responsibility for any troubles, such as dropping products caused during transportation out of Sanken's distribution network. • The contents in this document must not be transcribed or copied without Sanken's written consent. LC5222D/25D_22S/25S-DS SANKEN ELECTRIC CO., LTD. 11 August 8, 2012