AH286 HALL-EFFECT SMART FAN MOTOR CONTROLLER Description Pin Assignments The AH286 is a single-chip solution for driving two-coil brushless direct current (BLDC) fans and motors. The device includes a Hall-effect sensor, dynamic offset correction and two complementary open-drain output drivers with internal Zener diode protection. (Top View) To help protect the motor coils, the AH286 provides Rotor Lock Protection which shuts down output drives if rotor lock is detected. The device automatically re-starts when the rotor lock is removed. A Rotor-lock Detect (RD) output flag allows external monitoring of any motor locks. Vdd 1 GND 2 5 RD 286 DO 3 74 DOB SOT89-5L The AH286 is available in SOT89-5L package. Features Applications • • • • • • • • • • • Single-chip solution Operating Voltage: 3.8V to 20V Built-in Hall sensor and input amplifier Rotor-lock Detect (RD) flag Rotor Lock Protection (Lock detection, output shutdown and automatic re-start) Built-in Zener protection for output driver Average output current up to 500mA Packaged in SOT89-5L Green Molding Compound Two-coil BLDC cooling fans Low to medium voltage, low power BLDC motors Typical Application Circuit D2 Vdd (12V) D1 R pu 5 4 Coil2 286 RD 1 D3 2 Coil1 3 C3 GND R1 R2 C1 C2 12V DC Brush-Less Fan with RD Output Function Notes: 1. Typically it is recommended to us a 56 Ohm resistor for R1 and R2 and a 2.2μF E-Cap capacitor for C1, C2 and C3. These values may need to be optimized depending on the coils used. To help with IC protection it’s advised to add a Zener diode between Vdd and ground. The Zener diode should be chosen to help prevent the supply voltage exceeding the maximum rating of the device. AH286 Document number: DS31030 Rev. 12 - 2 1 of 9 www.diodes.com June 2010 © Diodes Incorporated AH286 HALL-EFFECT SMART FAN MOTOR CONTROLLER Pin Descriptions Pin Name RD Vdd DO DOB GND Description Rotor-state detection Input power Output pin Output pin Ground Functional Block Diagram Vdd Lock detect, shutdown and automatic re-start Regulator DO Hall Plate Control Logic Amp. DOB GND AH286 Document number: DS31030 Rev. 12 - 2 2 of 9 www.diodes.com RD June 2010 © Diodes Incorporated AH286 HALL-EFFECT SMART FAN MOTOR CONTROLLER Absolute Maximum Ratings (TA = 25°C) Symbol Characteristics Vdd Supply Voltage IO Output Current IO (AVE) IO (PEAK) PD TST TJ Power Dissipation Storage Temperature Maximum Junction Temperature θJA Thermal Resistance Junction to Case (Note 2) Rating Unit 24 500 700 800 -55 ~ 150 150 V mA mA mW °C °C 156 °C/W TA TJ Tc θ JA θ JC Notes: 2. θJA should be confirmed with heat sink thermal resistance. If there is no heat sink contact, θJA will almost be the same as θJC.. Recommended Operating Conditions Symbol Vdd TA Characteristic Supply Voltage Operating Ambient Temperature AH286 Document number: DS31030 Rev. 12 - 2 Conditions Min Max Unit Operating Operating 3.8 -40 20 100 V °C 3 of 9 www.diodes.com June 2010 © Diodes Incorporated AH286 HALL-EFFECT SMART FAN MOTOR CONTROLLER Electrical Characteristics (TA = 25 °C, Vdd = 12V, unless otherwise specified) Symbol Characteristics Conditions Min Typ. Max Unit Idd Supply Current Operating - 2.0 4.0 mA IOFF Output Leakage Current VOUT = 24V - < 0.1 10 μA TRLP-ON Rotor Lock Protection On Time 0.4 0.5 0.6 Sec TRLP-OFF Rotor Lock Protection Off Time 2.4 3 3.6 Sec VOUT(SAT) Output Saturation Voltage IO = 300mA - 375 500 IO = 500mA - 625 900 Output On Resistance IO = 300mA - 1.25 1.67 ohm VOL RD Output Vds IO = 10mA - 0.5 - V Vz Output Zener-Breakdown Voltage 35 42 60 V RDS(ON) Truth Table (Note 3) ININ+ H L L H Notes: CT L L H OUT1 H L off OUT2 L H off RD L L H mV Mode Rotating Rotating Lockup protection activated 3. Latch-type RD output is low during rotor rotation and high when the rotor is locked (not rotating) Magnetic Characteristics (TA = 25 °C, Vdd = 12V, unless otherwise specified, Note 4) (1mT = 10 Gauss) Symbol Bop Brp Bhy Notes: Characteristics Operate Point Release Point Hysteresis Min Typ. Max Unit 10 -60 - 30 -30 60 60 -10 - Gauss Gauss Gauss 4. The magnetic characteristics may vary with supply voltage, operating temperature and after soldering. AH286 Document number: DS31030 Rev. 12 - 2 4 of 9 www.diodes.com June 2010 © Diodes Incorporated AH286 HALL-EFFECT SMART FAN MOTOR CONTROLLER Operating Characteristics DO 12 RP Output Voltage in Volts Output Voltage in Volts DOB OFF 10 8 6 4 2 ON OP Vsat Brp 0 12 OFF OP 10 8 6 4 2 RP ON Vsat Bop Brp Magnetic Flux Density in Gauss 0 Bop Magnetic Flux Density in Gauss S Marking side N ( SOT89-5L ) AH286 Document number: DS31030 Rev. 12 - 2 5 of 9 www.diodes.com June 2010 © Diodes Incorporated AH286 HALL-EFFECT SMART FAN MOTOR CONTROLLER Performance Characteristics 25 800 105 288 TA (°C) PD (mW) TA (°C) PD (mW) 50 640 110 256 P D (mW ) 60 576 115 224 70 512 120 192 75 480 125 160 80 448 130 128 85 416 135 96 90 384 140 64 95 352 145 32 100 320 150 0 Power Dissipation Curve 900 800 700 600 500 400 300 200 100 0 -4 00 25 50 75 10 0 125 1 50 T A (°C) AH286 Document number: DS31030 Rev. 12 - 2 6 of 9 www.diodes.com June 2010 © Diodes Incorporated AH286 HALL-EFFECT SMART FAN MOTOR CONTROLLER Ordering Information AH 286 - Y G - 13 Device AH286-YG-13 Notes: Package Green Packing Y : SOT89-5L G : Green (Note 5) 13 : Tape & Reel Package Code Packaging (Note 6, 7) Y SOT89-5L Bulk Part Number Quantity Suffix NA NA 13” Tape and Reel Part Number Quantity Suffix 2500/Tape & Reel -13 5. EU Directive 2002/95/EC (RoHS). All applicable RoHS exemptions applied. Please visit our website at http://www.diodes.com/products/lead_free.html. 6. Pad layout as shown on Diodes Inc. suggested pad layout document AP02001, which can be found on our website at http://www.diodes.com/datasheets/ap02001.pdf. 7. Reverse taping as shown on Diodes Inc. Surface Mount (SMD) Packaging document AP02007, which can be found on our website http://www.diodes.com/datasheets/ap02007.pdf. Marking Information (Top View) 4 7 5 286 Y W X 1 2 Y : Year : 0~9 W : Week : A~Z : 1~26 week; a~z : 27~52 week; z represents 52 and 53 week X : Internal code A~Z : Green 3 SOT89-5L AH286 Document number: DS31030 Rev. 12 - 2 7 of 9 www.diodes.com June 2010 © Diodes Incorporated AH286 HALL-EFFECT SMART FAN MOTOR CONTROLLER Package Outline Dimensions (All Dimensions in mm) Sensor Location AH286 Document number: DS31030 Rev. 12 - 2 8 of 9 www.diodes.com June 2010 © Diodes Incorporated AH286 HALL-EFFECT SMART FAN MOTOR CONTROLLER IMPORTANT NOTICE DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION). Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability arising out of the application or use of this document or any product described herein; neither does Diodes Incorporated convey any license under its patent or trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on Diodes Incorporated website, harmless against all damages. Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel. Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall indemnify and hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized application. Products described herein may be covered by one or more United States, international or foreign patents pending. Product names and markings noted herein may also be covered by one or more United States, international or foreign trademarks. LIFE SUPPORT Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express written approval of the Chief Executive Officer of Diodes Incorporated. As used herein: A. Life support devices or systems are devices or systems which: 1. are intended to implant into the body, or 2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in significant injury to the user. B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or to affect its safety or effectiveness. Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or systems, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of Diodes Incorporated products in such safety-critical, life support devices or systems, notwithstanding any devices- or systems-related information or support that may be provided by Diodes Incorporated. Further, Customers must fully indemnify Diodes Incorporated and its representatives against any damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems. Copyright © 2010, Diodes Incorporated www.diodes.com AH286 Document number: DS31030 Rev. 12 - 2 9 of 9 www.diodes.com June 2010 © Diodes Incorporated