ON NB6L16D Evaluation board manual for high frequency soic 8 Datasheet

ECLSOIC8EVB
Evaluation Board Manual
for High Frequency SOIC 8
http://onsemi.com
EVALUATION BOARD MANUAL
Board Lay−Up
INTRODUCTION
ON Semiconductor has developed an evaluation board for
the devices in 8−lead SOIC package. These evaluation
boards are offered as a convenience for the customers
interested in performing their own engineering assessment
on the general performance of the 8−lead SOIC device
samples. The board provides a high bandwidth 50 controlled impedance environment. The pictures in Figure 1
show the top and bottom view of the evaluation board, which
can be configured in several different ways, depending on
device under test (See Table 1. Configuration List).
This evaluation board manual contains:
• Information on 8−lead SOIC Evaluation Board
• Assembly Instructions
• Appropriate Lab Setup
• Bill of Materials
This manual should be used in conjunction with the device
data sheet, which contains full technical details on the device
specifications and operation.
The 8−lead SOIC evaluation board is implemented in four
layers with split (dual) power supplies (Figure 2.
Evaluation Board Lay−up). For standard ECL lab setup and
test, a split (dual) power supply is essential to enable the
50 internal impedance in the oscilloscope as a termination
for ECL devices. The first layer or primary trace layer is
0.008″ thick Rogers RO4003 material, which is designed to
have equal electrical length on all signal traces from the
device under the test (DUT) to the sense output. The second
layer is the 1.0 oz copper ground plane and a portion of the
plane is the VEE power plane. The FR4 dielectric material is
placed between second and third layer and between third and
fourth layer. The third layer is also 1.0 oz copper ground
plane and a portion of this layer is VCC power plane. The
fourth layer is the secondary trace layer.
Figure 1. Top and Bottom View of the 8−lead SOIC Evaluation Board
 Semiconductor Components Industries, LLC, 2004
August, 2004 − Rev. 1
1
Publication Order Number:
ECLSOIC8EVB/D
ECLSOIC8EVB
LAY−UP DETAIL
4 LAYER
SILKSCREEN (TOP SIDE)
LAYER 1 (TOP SIDE)
ROGERS 4003 0.008 in
LAYER 2 (GROUND AND VEE PLANE P1) 1 OZ
FR−4 0.020 in
LAYER 3 (GROUND AND VCC PLANE P2) 1 OZ
FR−4 0.025 in
LAYER 4 (BOTTOM SIDE)
0.062 0.007
Figure 2. Evaluation Board Lay−up
Board Layout
devices and the relevant configuration that utilizes this PCB
board. List of components and simple schematics are located
in Figures 4 through 14. Place SMA connectors on J1
through J7, 50 chip resistors on R1 through R7, and chip
capacitors C1 through C4 according to configuration
figures. (C1 and C2 are 0.01 F and C3 and C4 are 0.1 F).
The 8−lead SOIC evaluation board was designed to be
versatile and accommodate several different configurations.
The input, output, and power pin layout of the evaluation
board is shown in Figure 3. The evaluation board has at least
eleven possible configurable options. Table 1. list the
Top View
Bottom View
Figure 3. Evaluation Board Layout
http://onsemi.com
2
ECLSOIC8EVB
Table 1. Configuration List
ECLinPS Plus
ECLinPS Lite
Device
Comments
Configuration
Device
Comments
Configuration
MC10EL01D/MC100EL01D
See Figure 4
1
MC10EP01D/MC100EP01D
See Figure 4
1
MC10EL04D/MC100EL04D
See Figure 5
2
MC10EP05D/MC100EP05D
See Figure 4
1
MC10EL05D/MC100EL05D
See Figure 4
1
MC10EP08D/MC100EP08D
See Figure 4
1
See Figure 6
3
MC10EL07D/MC100EL07D
See Figure 5
2
MC10EP11D/MC100EP11D
MC10EL11D/MC100EL11D
See Figure 6
3
MC10EP16D/
MC100EP16D*
See Figure 5
2
MC10EL12D/MC100EL12D
See Figure 6
3
MC10EL16D/MC100EL16D*
See Figure 5
2
MC100EP16FD*
See Figure 5
2
MC10EL31D/MC100EL31D
See Figure 4
1
MC10EP16TD/
MC100EP16TD*
See Figure 5
2
MC10EL32D/MC100EL32D
See Figure 7
4
MC100EP16VAD*
See Figure 5
2
MC10EL33D/MC100EL33D
See Figure 7
4
MC100EP16VBD*
See Figure 5
2
MC10EL35D/MC100EL35D
See Figure 4
1
MC100EP16VCD*
See Figure 8
5
MC10EL51D/MC100EL51D
See Figure 4
1
MC100EP16VSD*
See Figure 5
2
MC10EL52D/MC100EL52D
See Figure 4
1
MC100EP16VTD*
See Figure 5
2
MC10EL58D/MC100EL58D
See Figure 8
5
MC10EP31D/MC100EP31D
See Figure 4
1
MC10EL89D/MC100EL89D
See Figure 6
3
MC10EP32D/MC100EP32D
See Figure 7
4
MC10ELT20D/
MC100ELT20D
See Figure 9
6
MC10EP33D/MC100EP33D
See Figure 7
4
MC10ELT21D/
MC100ELT21D
See Figure 10
7
MC10EP35D/MC100EP35D
See Figure 4
1
MC10EP51D/MC100EP51D
See Figure 4
1
MC10ELT22D/
MC100ELT22D
See Figure 11
8
MC10EP52D/MC100EP52D
See Figure 4
1
MC10EP58D/MC100EP58D
See Figure 8
5
MC100ELT23D
See Figure 12
9
MC100EP89D
See Figure 6
3
MC10ELT26D/
MC100ELT26D
See Figure 13
10
MC10EPT20D/
MC100EPT20D
See Figure 9
6
MC10ELT28D/
MC100ELT28D
See Figure 14
11
MC100EPT21D*
See Figure 10
7
MC100EPT22D
See Figure 11
8
MC100EPT23D*
See Figure 12
9
MC100EPT26D*
See Figure 13
10
Low Voltage ECLinPS
Device
Comments
Configuration
MC100LVEL01D
See Figure 4
1
MC100LVEL05D
See Figure 4
1
MC100LVEL11D
See Figure 6
3
MC100LVEL12D
See Figure 6
3
MC100LVEL16D*
See Figure 5
2
MC100LVEL31D
See Figure 4
1
MC100LVEL32D
See Figure 7
4
MC100LVEL33D
See Figure 7
4
MC100LVEL51D
See Figure 4
1
MC100LVEL58D
See Figure 8
5
MC100LVELT22D
See Figure 11
8
MC100LVELT23D
See Figure 12
9
Low Voltage ECLinPS Plus
Comments
Configuration
MC100LVEP11D
Device
See Figure 6
3
MC100LVEP16D*
See Figure 5
2
*See Appendix for additions or modifications to the current
configuration.
ECLinPS MAX
Device
Comments
Configuration
NB6L11D
See Figure 6
3
NB6L16D
See Figure 5
2
http://onsemi.com
3
ECLSOIC8EVB
Evaluation Board Assembly Instructions
The 8−lead SOIC evaluation board is designed for
characterizing devices in a 50 laboratory environment
using high bandwidth equipment. Each signal trace on the
board has a via, which has an option of termination resistor
or bypassing capacitor depending on the input/output
configuration (see Table 1. Configuration List). Table 17
contains the Bill of Materials for this evaluation board.
On the top side of the evaluation board solder the four
surface mount test point clips to the pads labeled VCC, VEE,
and GND. The VCC clip connects directly to pin 8 of the
device. The VEE clip connects directly to pin 5 of the device.
There are two GND clip footprints which can be connected
to the ground plane of the evaluation board depending on the
setup configuration.
It is recommended to solder 0.01 F capacitors to C1 and
C2 to reduce the unwanted noise from the power supplies.
C3 and C4 pads are provided for 0.1 F capacitor to further
diminish the noise from the power supplies. Adding
capacitors can improve edge rates, reduce overshoot and
undershoot.
Solder the Device on the Evaluation Board
The soldering can be accomplished by hand soldering or
soldering re−flow techniques. Make sure pin 1 of the device
is located next the white dotted mark U1 and all the pins are
aligned to the footprint pads. Solder the 8−lead SOIC device
to the evaluation board.
Termination
All ECL outputs need to be terminated to VTT (VTT = VCC
–2.0 V = GND) via a 50 resistor in a split power supply
lab set−up. 0603 chip resistor pads are provided on the
bottom side of the evaluation board to terminate the ECL
driver (More information on termination is provided in
AN8020). Solder the chip resistors to the bottom side of the
board on the appropriate input of the device pins labeled R1,
R2, R3, R4, R6, and R7, depending on the specific device.
Connecting Power and Ground Planes
For standard ECL lab setup and test, a split (dual) power
supply is required enabling the 50 internal impedance in
the oscilloscope to be used as a termination of the ECL
signals (VTT = VCC – 2.0 V, in split power supply setup, VTT
is the system ground, VCC is 2.0 V, and VEE is –3.0 V or
–1.3 V; see Table 2: Power Supply Levels).
Installing the SMA Connectors
Table 2. Power Supply Levels
Power Supply
VCC
VEE
GND
5.0 V
2.0 V
−3.0 V
0.0 V
3.3 V
2.0 V
−1.3 V
0.0 V
2.5 V
2.0 V
−0.5 V
0.0 V
Each configuration indicates the number of SMA
connectors needed to populate an evaluation board for a
given configuration. Each input and output requires one
SMA connector. Attach all the required SMA connectors
onto the board and solder the connectors to the board. Please
note that alignment of the signal connector pin of the SMA
can influence the lab results. The reflection and launch of the
signals are largely influenced by imperfect alignment and
soldering of the SMA connector.
The power supply for voltage level translating device need
slight modification as indicated in Table 3. Power Supply
Levels for Translators.
Validating the Assembled Board
Table 3. Power Supply Levels for Translators
PECL Translators
VCC
VEE
GND
3.3 V / 5.0 V
0.0 V
0.0 V
After assembling the evaluation board, it is recommended
to perform continuity checks on all soldered areas before
commencing with the evaluation process. Time Domain
Reflectometry (TDR) is another highly recommended
validation test.
http://onsemi.com
4
ECLSOIC8EVB
CONFIGURATIONS
VCC
GND
C4
0.1 F
R1
50 C1
0.01 F
J1
R2
50 DUT
J5
J2
R3
50 C2
0.01 F
J3
J6
R4
50 C3
0.1 F
J4
VEE
GND
Figure 4. Configuration 1 Schematic
Table 4. Configuration 1
Pin 1
Device
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
Pin 7
Pin 8
J1
R1
J2
R2
J3
R3
J4
R4
C2
C3
J6
R6
J7
R7
C1
C4
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes
No
Yes
Yes
MC10EL01D/MC100EL01D
MC10EL05D/MC100EL05D
MC10EL31D/MC100EL31D
MC10EL35D/MC100EL35D
MC10EL51D/MC100EL51D
MC10EL52D/MC100EL52D
MC100LVEL01D
MC100LVEL05D
MC100LVEL31D
MC100LVEL51D
MC10EP01D/MC100EP01D
MC10EP05D/MC100EP05D
MC10EP08D/MC100EP08D
MC10EP31D/MC100EP31D
MC10EP35D/MC100EP35D
MC10EP51D/MC100EP51D
MC10EP52D/MC100EP52D
http://onsemi.com
5
ECLSOIC8EVB
VCC
GND
C4
0.1 F
Pin 1
Pin 8
C1
0.01 F
Pin 7
Pin 2
R2
50 DUT
J2
J7
Pin 3
R3
50 Pin 6
C2
0.01 F
J3
Pin 4
J6
Pin 5
C3
0.1 F
J4
(Optional)
VEE
GND
Figure 5. Configuration 2 Schematic
Table 5. Configuration 2
Pin 1
Device
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
Pin 7
Pin 8
J1
R1
J2
R2
J3
R3
J4
R4
C2
C3
J6
R6
J7
R7
C1
C4
No
No
Yes
Yes
Yes
Yes
No
No
Yes
Yes
Yes
No
Yes
No
Yes
Yes
MC10EL04D/MC100EL04D
MC10EL07D/MC100EL07D
MC10EL16D/MC100EL16D*
MC100LVEL16D*
MC10EP16D/MC100EP16D*
MC100EP16FD*
MC100LVEP160*
MC10EP16TD/MC100EP16TD*
MC100EP16VAD*
MC100EP16VBD*
MC100EP16VSD*
MC100EP16VTD*
NB6L160D
*See Appendix for additional or modification to the current configuration
http://onsemi.com
6
ECLSOIC8EVB
VCC
GND
C4
0.1 F
Pin 1
Pin 8
C1
0.01 F
J1
Pin 7
Pin 2
R7
50 DUT
J2
J7
Pin 3
Pin 6
R6
50 C2
0.01 F
J3
Pin 4
J6
Pin 5
C3
0.1 F
J4
VEE
GND
Figure 6. Configuration 3 Schematic
Table 6. Configuration 3
Pin 1
Device
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
Pin 7
Pin 8
J1
R1
J2
R2
J3
R3
J4
R4
C2
C3
J6
R6
J7
R7
C1
C4
Yes
No
Yes
No
Yes
No
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
MC10EL11D/MC100EL11D
MC10EL12D/MC100EL12D
MC10EL89D/MC100EL89D
MC100LVEL11D
MC100LVEL12D
MC10EP11D/MC100EP11D
MC100EP89D
MC100LVEP11D
NB6L11D
http://onsemi.com
7
ECLSOIC8EVB
VCC
GND
C4
0.1 F
Pin 1
R1
50 Pin 8
C1
0.01 F
J1
Pin 7
Pin 2
R2
50 DUT
J2
J7
Pin 3
Pin 6
R3
50 J3
Pin 4
C2
0.01 F
Pin 5
J6
C3
0.1 F
J4
(Optional)
VEE
GND
Figure 7. Configuration 4 Schematic
Table 7. Configuration 4
Pin 1
Device
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
Pin 7
Pin 8
J1
R1
J2
R2
J3
R3
J4
R4
C2
C3
J6
R6
J7
R7
C1
C4
Yes
Yes
Yes
Yes
Yes
Yes
No
No
Yes
Yes
Yes
No
Yes
No
Yes
Yes
MC10EL32D/MC100EL32D
MC10EL33D/MC100EL33D
MC100LVEL32D
MC100LVEL33D
MC10EP32D/MC100EP32D
MC10EP33D/MC100EP33D
http://onsemi.com
8
ECLSOIC8EVB
VCC
GND
C4
0.1 F
Pin 1
Pin 8
C1
0.01 F
R2
50 Pin 7
DUT
Pin 2
J2
J7
R3
50 J3
Pin 3
Pin 6
Pin 4
Pin 5
C2
0.01 F
J6
R4
50 C3
0.1 F
J4
(Optional)
VEE
GND
Figure 8. Configuration 5 Schematic
Table 8. Configuration 5
Pin 1
Device
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
Pin 7
Pin 8
J1
R1
J2
R2
J3
R3
J4
R4
C2
C3
J6
R6
J7
R7
C1
C4
No
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes
No
Yes
Yes
MC100EP16VCD*
MC10EL58D/MC100EL58D
MC100LVEL58D
MC10EP58D/MC100EP58D
*See Appendix for addition or modification to the current configuration
http://onsemi.com
9
ECLSOIC8EVB
VCC
GND
C4
0.1 F
Pin 1
Pin 8
C1
0.01 F
Pin 7
Pin 2
R7
50 (optional) J7
DUT
J2
Pin 3
Pin 6
Pin 4
Pin 5
J3
Short
VEE
GND
Figure 9. Configuration 6 − Translator Schematic
Table 9. Configuration 6
Pin 1
Device
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
Pin 7
Pin 8
J1
R1
J2
R2
J3
R3
J4
R4
C2
C3
J6
R6
J7
R7
C1
C4
No
No
Yes
No
Yes
No
No
No
No
No
No
No
Yes
Optional
Yes
Yes
MC10ELT20D/MC100EL20D
MC10EPT20D/MC100EPT20D
http://onsemi.com
10
ECLSOIC8EVB
VCC
GND
C4
0.1 F
Pin 1
Pin 8
C1
0.01 F
Pin 7
Pin 2
R2
50 DUT
J2
J7
R3
50 Pin 3
Pin 6
Pin 4
Pin 5
J3
Short
VEE
GND
Figure 10. Configuration 7 − Translator Schematic
(Unloaded Testing Condition)
Table 10. Configuration 7
Pin 1
Device
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
Pin 7
Pin 8
J1
R1
J2
R2
J3
R3
J4
R4
C2
C3
J6
R6
J7
R7
C1
C4
No
No
Yes
Yes
Yes
Yes
No
No
No
No
No
No
Yes
No
Yes
Yes
MC10ELT21D/MC100EL21D
MC100EPT21D
*See Appendix for loaded testing condition.
http://onsemi.com
11
ECLSOIC8EVB
VCC
GND
C4
0.1 F
Pin 1
Pin 8
C1
0.01 F
J1
Pin 7
Pin 2
R7
50 (optional) J7
DUT
J2
Pin 3
Pin 6
Pin 4
Pin 5
R6
50 (optional) J6
J3
Short
J4
VEE
GND
Figure 11. Configuration 8 − Translator Schematic
Table 11. Configuration 8
Pin 1
Device
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
Pin 7
Pin 8
J1
R1
J2
R2
J3
R3
J4
R4
C2
C3
J6
R6
J57
R7
C1
C4
Y
Yes
N
No
Y
Yes
N
No
Y
Yes
N
No
Y
Yes
N
No
N
No
N
No
Y
Yes
O ti
Optional
l
Y
Yes
O ti
Optional
l
Y
Yes
Y
Yes
MC10ELT22D/
MC100EL22D
MC100LVELT22D
MC100EPT22D
http://onsemi.com
12
ECLSOIC8EVB
VCC
GND
C4
0.1 F
Pin 1
R1
50 Pin 8
C1
0.01 F
J1
Pin 7
Pin 2
R2
50 DUT
J2
J7
Pin 3
R3
50 Pin 6
J3
J6
Pin 4
R4
50 Pin 5
Short
J4
VEE
GND
Figure 12. Configuration 9 − Translator Schematic
(Unloaded Testing Condition)
Table 12. Configuration 9
Pin 1
Device
Pin 2
Pin 3
J1
R1
J2
R2
J3
Yes
Yes
Yes
Yes
Yes
R3
Pin 4
Pin 5
Pin 6
Pin 7
Pin 8
J4
R4
C2
C3
J6
R6
J7
R7
C1
C4
Yes
Yes
No
No
Yes
No
Yes
No
Yes
Yes
MC100EL23D
MC100LVELT23D
Y
Yes
MC100EPT23D
*See Appendix for loaded testing condition.
http://onsemi.com
13
ECLSOIC8EVB
VCC
GND
C4
0.1 F
Pin 1
Pin 8
C1
0.01 F
Pin 7
Pin 2
R2
50 DUT
J2
J7
Pin 3
R3
50 Pin 6
J3
J6
Pin 4
Pin 5
Short
VEE
GND
Figure 13. Configuration 10 − Translator Schematic
(Unloaded Testing Condition)
Table 13. Configuration 10
Pin 1
Device
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
J1
R1
J2
R2
J3
R3
J4
R4
C2
C3
J6
R6
No
No
Yes
Yes
Yes
Yes
No
No
No
No
Yes
Yes
MC10ELT26D/MC100ELT26D
MC100EPT26D
*See Appendix for loaded testing condition.
http://onsemi.com
14
Pin 7
J7
Yes
R7
No
Pin 8
C1
C4
Yes
Yes
ECLSOIC8EVB
VCC
GND
C4
0.1 F
Pin 1
R1
50 Pin 8
C1
0.01 F
J2
Pin 7
Pin 2
R2
50 DUT
J2
J7
Pin 3
R6
50 (optional)
Pin 6
J3
Pin 4
J6
Pin 5
Short
J3
VEE
GND
Figure 14. Configuration 11 − Translator Schematic
Table 14. Configuration 11
Pin 1
Device
MC10ELT28D/MC100ELT28D
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
Pin 7
Pin 8
J1
R1
J2
R2
J3
R3
J4
R4
C2
C3
J6
R6
J7
R7
C1
C4
Yes
Yes
Yes
Yes
Yes
No
Yes
No
No
No
Yes
Optional
Yes
No
Yes
Yes
http://onsemi.com
15
ECLSOIC8EVB
LAB SETUP
Power Supply
VCC
GND
OUT1
Test Measuring
Equipment
J1
J2
J7
Channel 1
OUT1
Differential
Signal Generator
DUT
Channel 2
OUT2
J3
J6
J4
OUT2
TRIGGER
TRIGGER
GND
VEE
Power Supply
Figure 15. Example of Standard Lab Setup (Configuration 1)
1. Connect appropriate power supplies to VCC, VEE,
and GND.
For standard ECL lab setup and test, a split (dual)
power supply is required enabling the 50 internal impedance in the oscilloscope to be used
as a termination of the ECL signals (VTT = VCC
– 2.0 V, in split power supply setup, VTT is the
system ground, VCC is 2.0 V, and VEE is –3.0 V or
–1.3 V; see Table 15).
The power supply for voltage level translating device need
slight modification as indicated in Table 16.
Table 16. Power Supply Levels for Translators
PECL Translators
VCC
VEE
GND
5.0 V
2.0 V
−3.0 V
0.0 V
3.3 V
2.0 V
−1.3 V
0.0 V
2.5 V
2.0 V
−0.5 V
0.0 V
VEE
GND
3.3 V / 5.0 V
0.0 V
0.0 V
2. Connect a signal generator to the input SMA
connectors. Setup input signal according to the
device data sheet.
3. Connect a test measurement device on the device
output SMA connectors.
NOTE: The test measurement device must contain 50 termination.
Table 15. Power Supply Levels
Power Supply
VCC
http://onsemi.com
16
ECLSOIC8EVB
Table 17. Bill of Materials
Components
SMA Connector
Surface Mount Test
Points
Chip Capacitor
Chip Resistor
Manufacturer
Description
Part Number
Web Site
Rosenberger
SMA Connector, Side
Launch, Gold Plated
32K243−40ME3
http://www.rosenberger.de
http://www.rosenbergerna.com
Johnson
Components*
SMA Connector, Side
Launch, Gold Plated
142−0701−851
http://www.johnsoncomponents.com
Keystone*
AVC Corporation*
Vishay Dale*
SMT Miniature Test Point
5015
SMT Compact Test Point
5016
http://www.keyelco.com
Thru−Hole Mount
Compact Test Point
5005−5009
0603 0.01 F ±10%
06035C103KAT2A
0603 0.1 F ±10%
06035C104KAT2A
0603 50 ± 1% Thick
Film Resistor
CRCW060351R1J
http://www.vishay.com
http://www.avxcorp.com
Evaluation Board
ON Semiconductor
SOIC 8 Evaluation Board
ECLSOIC8EVB
http://www.onsemi.com
Device Samples
ON Semiconductor
SOIC 8 Package Device
Various
http://www.onsemi.com
*Components are available through most distributors, i.e. www.newark.com, www.digikey.com
http://onsemi.com
17
ECLSOIC8EVB
Appendix A (Modified Configurations)
MC100EP16VSD
This device has an option of varying the output swing
amplitude and being driven single−endedly. In order to
utilize these options, Configuration 2 needs to be modified.
Output Swing Control
1. Connect a SMA connector on J1
2. Add a decoupling capacitor between J1 and VCC
(0.01 F)
Drive Single−Endedly
1. Remove the 50 chip resistor from R3.
2. Short pin 3 and pin 4 together.
Option A) Short R3 and R4.
Or
Option B) Place a SMA connector on J4 and use
a cable with SMA connectors to short
J3 and J4 connectors.
MC10EL16D/MC100EL16D
MC100LVEL16D
MC10EP16D/MC100EP16D
MC10EP16DF/MC100EP16DF
MC100EP16VAD
MC100LVEP16D
The devices listed above have the option of being driven
single−endedly by using the provided VBB pin of the device.
In order to drive it single−endedly, Configuration 2 needs to
be modified.
1. Remove the 50 chip resistor from R3.
2. Short pin 3 and pin 4 together.
Option A) Short R3 and R4 trace pads.
Or
Option B) Place a SMA connector on J4 and use
a cable with SMA connectors to short
J3 and J4 connectors.
MC100EP16VTD
This device has an option of varying the output swing
amplitude and internal termination. In order to utilize these
options, Configuration 2 needs to be modified.
Output Swing Control
1. Connect a SMA connector on J1
2. Add a decoupling capacitor between J1 and VCC
(0.0 1 F)
Internal Termination
1. Remove the 50 chip resistors from R2 and R3.
2. Short R1 and R4 to VTT (GND)
Option A) Short R1 and R4 to VTT (GND).
Or
Option B) Place SMA connectors on J1 and J4.
Place shorting barrels on J1 and J4
SMA connector.
MC10EP16D/MC100EP16DT
This device has an option of being 50 terminated
internally. To evaluate the internal 50 resistor of the
device, Configuration 2 needs to be modified.
1. Remove the 50 chip resistors from R2 and R3.
2. Short R1 and R4 to VTT (GND).
Option A) Short R1 and R4 to VTT (GND).
Or
Option B) Place SMA connectors on J1 and J4.
Place shorting barrels on J1 and J4
SMA connector.
MC100EP16VBD
This device has an option of single−ended feedback
output and being driven single−endedly using the VBB. To
utilize the feedback option and drive it single−endedly,
Configuration 2 needs to be modified.
Feedback option
1. Connect a SMA connector on J1
Drive single−endedly
2. Remove the 50 chip resistor from R3.
3. Short pin 3 and pin 4 together.
Option A) Short R3 and R4.
Or
Option B) Place a SMA connector on J4 and use
a cable with SMA connectors to short
J3 and J4 connectors.
MC10ELT21D/MC100EL21D
MC100EL23D
MC10ELT26D/MC100ELT26D
MC100EPT21D
MC100EPT23D
MC100EPT26D
MC100LVELT23
The TTL output data presented in the data sheet are obtained
under 500 load resistor in parallel with 20 pF fixture
capacitance. In order to obtain comparable data as in the data
sheet, the evaluation board needs to be modified.
1. Cut the output trace so that the 0402* size chip
resistor can be placed over the cut out trace.
2. Solder a 450 chip resistor across the cut out
trace.
MC100EP16VCD
This device has an option of single−ended feedback
output with an enable pin. To utilize the feedback option and
enable option, Configuration 5 needs to be modified.
1. Connect a SMA connector on J1.
2. Remove the 50 chip resistor from R3.
*Any size chip resistor can be used. The recommended size of the
chip resistor is 0402, to reduce the effect of parasitic with a 17 mil
trace width. 450 in series with 50 instrument resistance add up
to 500 loaded condition.
http://onsemi.com
18
ECLSOIC8EVB
Appendix B (Gerber Files)
Top Layer
Third Layer (VCC and Ground Plane)
Second Layer (VEE and Ground Plane
Bottom Layer
Figure 16. Gerber Files
http://onsemi.com
19
ECLSOIC8EVB
ECLinPS, ECLinPS Lite, ECLinPS Plus, and ECLinPS MAX are trademarks of Semiconductor Components Industries, LLC (SCILLC).
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 61312, Phoenix, Arizona 85082−1312 USA
Phone: 480−829−7710 or 800−344−3860 Toll Free USA/Canada
Fax: 480−829−7709 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
ON Semiconductor Website: http://onsemi.com
Order Literature: http://www.onsemi.com/litorder
Japan: ON Semiconductor, Japan Customer Focus Center
2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051
Phone: 81−3−5773−3850
http://onsemi.com
20
For additional information, please contact your
local Sales Representative.
ECLSOIC8EVB/D
Similar pages