Single Channel, High Speed Optocouplers 6N135/6 HCNW135/6 HCNW4502/3 HCPL-2502 HCPL-0452/3 HCPL-0500/1 HCPL-4502/3 Technical Data Features Applications Description • 15 kV/µs Minimum Common Mode Transient Immunity at VCM = 1500 V (4503/0453) • High Speed: 1 Mb/s • TTL Compatible • Available in 8-Pin DIP, SO-8, Widebody Packages • Open Collector Output • Guaranteed Performance from Temperature: 0°C to 70°C • Safety Approval UL Recognized – 3750 V rms for 1 minute (5000 V rms for 1 minute for HCNW and Option 020 devices) per UL1577 CSA Approved IEC/EN/DIN EN 60747-5-2 Approved –VIORM = 630 V peak for HCPL-4503#060 –VIORM = 1414 V peak for HCNW devices • Dual Channel Version Available (253X/4534/053X/ 0534) • MIL-PRF-38534 Hermetic Version Available (55XX/ 65XX/4N55) • High Voltage Insulation • Video Signal Isolation • Power Transistor Isolation in Motor Drives • Line Receivers • Feedback Element in Switched Mode Power Supplies • High Speed Logic Ground Isolation – TTL/TTL, TTL/ CMOS, TTL/LSTTL • Replaces Pulse Transformers • Replaces Slow Phototransistor Isolators • Analog Signal Ground Isolation These diode-transistor optocouplers use an insulating layer between a LED and an integrated photodetector to provide electrical insulation between input and output. Separate connections for the photodiode bias and output-transistor collector increase the speed up to a hundred times that of a conventional phototransistor coupler by reducing the base-collector capacitance. Functional Diagram NC 1 8 VCC ANODE 2 * 7 VB CATHODE 3 6 VO NC 4 TRUTH TABLE (POSITIVE LOGIC) VO LED LOW ON HIGH OFF 5 GND * NOTE: FOR 4502/3, 0452/3, PIN 7 IS NOT CONNECTED. A 0.1 µF bypass capacitor must be connected between pins 5 and 8. CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD. 2 These single channel optocouplers are available in 8-Pin DIP, SO-8 and Widebody package configurations. output current for 1 TTL load and a 5.6 kΩ pull-up resistor. CTR for these devices is 19% minimum at IF = 16 mA. The 6N135, HCPL-0500, and HCNW135 are for use in TTL/ CMOS, TTL/LSTTL or wide bandwidth analog applications. Current transfer ratio (CTR) for these devices is 7% minimum at IF = 16 mA. The HCPL-4502, HCPL-0452, and HCNW4502 provide the electrical and switching performance of the 6N136, HCPL-0501, and HCNW136 with increased ESD protection. The 6N136, HCPL-2502, HCPL-0501, and HCNW136 are designed for high speed TTL/TTL applications. A standard 16 mA TTL sink current through the input LED will provide enough The HCPL-4503, HCPL-0453, and HCNW4503 are similar to the HCPL-4502, HCPL-0452, and HCNW4502 optocouplers but have increased common mode transient immunity of 15 kV/µs minimum at VCM = 1500 V guaranteed. Schematic 2 ANODE ICC + IO – dV/dt (V/µs) 1,000 VCM (V) 10 15,000 1,000 1500 10 8-Pin DIP (300 Mil) Current Single Dual Transfer Channel Channel Ratio (%) Package Package* 7 6N135 HCPL-2530 19 6N136 HCPL-2531 HCPL-4502† 15 HCPL-2502 19 HCPL-4503† HCPL-4534 9 6 VO 3 SHIELD HCPL-4503/0453 HCNW4503 5 IB 7 * VB * NOTE: FOR HCPL-4502/-3, HCPL-0452/3, HCNW4502/3, PIN 7 IS NOT CONNECTED. Selection Guide Minimum CMR VCC IF VF CATHODE 8 Small-Outline SO-8 Single Dual Channel Channel Package Package* HCPL-0500 HCPL-0530 HCPL-0501 HCPL-0531 HCPL-0452† Widebody (400 Mil) Hermetic Single Single and Channel Dual Channel Package Packages* HCNW135 HCNW136 HCNW4502† HCPL-0453† HCNW4503† HCPL-0534 HCPL-55XX HCPL-65XX 4N55 *Technical data for these products are on separate Agilent publications. †Pin 7, transistor base, is not connected. Ordering Information Specify Part Number followed by Option Number (if desired). Example: HCPL-4503#XXXX 020 = UL 5000 V rms/1 Minute Option* 060 = IEC/EN/DIN EN 60747-5-2 VIORM = 630 V peak Option** 300 = Gull Wing Surface Mount Option† 500 = Tape and Reel Packaging Option XXXE = Lead Free Option Option data sheets available. Contact your Agilent sales representative or authorized distributor for information. *For 6N135/6 and HCPL-4502/3 only. **For HCPL-4503 only. Combination of Option 020 and Option 060 is not available. †Gull wing surface mount option applies to through hole parts only. Remarks: The notation “#” is used for existing products, while (new) products launched since 15th July 2001 and lead free option will use “-” GND 3 Package Outline Drawings 8-Pin DIP Package (6N135/6, HCPL-4502/3, HCPL-2502) 7.62 ± 0.25 (0.300 ± 0.010) 9.65 ± 0.25 (0.380 ± 0.010) 8 TYPE NUMBER 7 6 5 6.35 ± 0.25 (0.250 ± 0.010) OPTION CODE* DATE CODE A XXXXZ YYWW RU 1 2 3 4 UL RECOGNITION 1.78 (0.070) MAX. 1.19 (0.047) MAX. + 0.076 0.254 - 0.051 + 0.003) (0.010 - 0.002) 5° TYP. 3.56 ± 0.13 (0.140 ± 0.005) 4.70 (0.185) MAX. 0.51 (0.020) MIN. 2.92 (0.115) MIN. DIMENSIONS IN MILLIMETERS AND (INCHES). 0.65 (0.025) MAX. 1.080 ± 0.320 (0.043 ± 0.013) *MARKING CODE LETTER FOR OPTION NUMBERS "L" = OPTION 020 "V" = OPTION 060 OPTION NUMBERS 300 AND 500 NOT MARKED. 2.54 ± 0.25 (0.100 ± 0.010) NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX. 8-Pin DIP Package with Gull Wing Surface Mount Option 300 (6N135/6, HCPL-4502/3) LAND PATTERN RECOMMENDATION 9.65 ± 0.25 (0.380 ± 0.010) 8 7 6 1.016 (0.040) 5 6.350 ± 0.25 (0.250 ± 0.010) 1 2 3 10.9 (0.430) 4 1.27 (0.050) 1.19 (0.047) MAX. 1.780 (0.070) MAX. 9.65 ± 0.25 (0.380 ± 0.010) 7.62 ± 0.25 (0.300 ± 0.010) 3.56 ± 0.13 (0.140 ± 0.005) 1.080 ± 0.320 (0.043 ± 0.013) 2.0 (0.080) 0.635 ± 0.25 (0.025 ± 0.010) 0.635 ± 0.130 2.54 (0.025 ± 0.005) (0.100) BSC DIMENSIONS IN MILLIMETERS (INCHES). LEAD COPLANARITY = 0.10 mm (0.004 INCHES). NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX. + 0.076 0.254 - 0.051 + 0.003) (0.010 - 0.002) 12° NOM. 4 Small Outline SO-8 Package (HCPL-0500/1, HCPL-0452/3) LAND PATTERN RECOMMENDATION 8 7 6 5 5.994 ± 0.203 (0.236 ± 0.008) XXX YWW 3.937 ± 0.127 (0.155 ± 0.005) TYPE NUMBER (LAST 3 DIGITS) 7.49 (0.295) DATE CODE PIN ONE 1 2 3 4 0.406 ± 0.076 (0.016 ± 0.003) 1.9 (0.075) 1.270 BSC (0.050) 0.64 (0.025) * 5.080 ± 0.127 (0.200 ± 0.005) 7° 3.175 ± 0.127 (0.125 ± 0.005) 45° X 0.432 (0.017) 0 ~ 7° 0.228 ± 0.025 (0.009 ± 0.001) 1.524 (0.060) 0.203 ± 0.102 (0.008 ± 0.004) * TOTAL PACKAGE LENGTH (INCLUSIVE OF MOLD FLASH) 5.207 ± 0.254 (0.205 ± 0.010) 0.305 MIN. (0.012) DIMENSIONS IN MILLIMETERS (INCHES). LEAD COPLANARITY = 0.10 mm (0.004 INCHES) MAX. 8-Pin Widebody DIP Package (HCNW135/6, HCNW4502/3) 11.00 MAX. (0.433) 11.15 ± 0.15 (0.442 ± 0.006) 8 7 6 9.00 ± 0.15 (0.354 ± 0.006) 5 TYPE NUMBER A HCNWXXXX DATE CODE YYWW 1 2 3 4 10.16 (0.400) TYP. 1.55 (0.061) MAX. 7° TYP. + 0.076 0.254 - 0.0051 + 0.003) (0.010 - 0.002) 5.10 MAX. (0.201) 3.10 (0.122) 3.90 (0.154) 0.51 (0.021) MIN. 2.54 (0.100) TYP. 1.78 ± 0.15 (0.070 ± 0.006) 0.40 (0.016) 0.56 (0.022) DIMENSIONS IN MILLIMETERS (INCHES). NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX. 5 8-Pin Widebody DIP Package with Gull Wing Surface Mount Option 300 (HCNW135/6, HCNW4502/3) 11.15 ± 0.15 (0.442 ± 0.006) 8 6 7 LAND PATTERN RECOMMENDATION 5 9.00 ± 0.15 (0.354 ± 0.006) 1 3 2 13.56 (0.534) 4 2.29 (0.09) 1.3 (0.051) 12.30 ± 0.30 (0.484 ± 0.012) 1.55 (0.061) MAX. 11.00 MAX. (0.433) 4.00 MAX. (0.158) 1.78 ± 0.15 (0.070 ± 0.006) 1.00 ± 0.15 (0.039 ± 0.006) 0.75 ± 0.25 (0.030 ± 0.010) 2.54 (0.100) BSC + 0.076 0.254 - 0.0051 + 0.003) (0.010 - 0.002) DIMENSIONS IN MILLIMETERS (INCHES). 7° NOM. LEAD COPLANARITY = 0.10 mm (0.004 INCHES). NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX. Solder Reflow Temperature Profile 300 TEMPERATURE (°C) PREHEATING RATE 3°C + 1°C/–0.5°C/SEC. REFLOW HEATING RATE 2.5°C ± 0.5°C/SEC. PEAK TEMP. 245°C PEAK TEMP. 240°C PEAK TEMP. 230°C 200 2.5°C ± 0.5°C/SEC. 30 SEC. 160°C 150°C 140°C SOLDERING TIME 200°C 30 SEC. 3°C + 1°C/–0.5°C 100 PREHEATING TIME 150°C, 90 + 30 SEC. 50 SEC. TIGHT TYPICAL LOOSE ROOM TEMPERATURE 0 0 50 100 150 TIME (SECONDS) 200 250 6 Recommended Pb-Free IR Profile tp Tp TEMPERATURE TL Tsmax TIME WITHIN 5 °C of ACTUAL PEAK TEMPERATURE 20-40 SEC. 260 +0/-5 °C 217 °C RAMP-UP 3 °C/SEC. MAX. 150 - 200 °C RAMP-DOWN 6 °C/SEC. MAX. Tsmin ts PREHEAT 60 to 180 SEC. tL 60 to 150 SEC. 25 t 25 °C to PEAK TIME NOTES: THE TIME FROM 25 °C to PEAK TEMPERATURE = 8 MINUTES MAX. Tsmax = 200 °C, Tsmin = 150 °C Regulatory Information The devices contained in this data sheet have been approved by the following organizations: UL Recognized under UL 1577, Component Recognition Program, File E55361. CSA Approved under CSA Component Acceptance Notice #5, File CA 88324. IEC/EN/DIN EN 60747-5-2 Approved under IEC 60747-5-2:1997 + A1:2002 EN 60747-5-2:2001 + A1:2002 DIN EN 60747-5-2 (VDE 0884 Teil 2):2003-01 (HCNW and Option 060 only) Insulation and Safety Related Specifications Parameter Minimum External Air Gap (External Clearance) Minimum External Tracking (External Creepage) Minimum Internal Plastic Gap (Internal Clearance) Minimum Internal Tracking (Internal Creepage) Tracking Resistance (Comparative Tracking Index) Isolation Group Symbol L(101) 8-Pin DIP (300 Mil) Value 7.1 SO-8 Value 4.9 L(102) 7.4 4.8 10.0 mm 0.08 0.08 1.0 mm NA NA 4.0 mm 200 200 200 Volts IIIa IIIa IIIa CTI Widebody (400 Mil) Value Units 9.6 mm Conditions Measured from input terminals to output terminals, shortest distance through air. Measured from input terminals to output terminals, shortest distance path along body. Through insulation distance, conductor to conductor, usually the direct distance between the photoemitter and photodetector inside the optocoupler cavity. Measured from input terminals to output terminals, along internal cavity. DIN IEC 112/VDE 0303 Part 1 Material Group (DIN VDE 0110, 1/89, Table 1) Option 300 - surface mount classification is Class A in accordance with CECC 00802. 7 IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics (HCPL-4503 OPTION 060 ONLY) Description Installation classification per DIN VDE 0110/1.89, Table 1 for rated mains voltage ≤ 300 V rms for rated mains voltage ≤ 450 V rms Climatic Classification Pollution Degree (DIN VDE 0110/1.89) Maximum Working Insulation Voltage Input to Output Test Voltage, Method b* VIORM x 1.875 = VPR, 100% Production Test with tm = 1 sec, Partial Discharge < 5 pC Input to Output Test Voltage, Method a* VIORM x 1.5 = VPR, Type and sample test, tm = 60 sec, Partial Discharge < 5 pC Highest Allowable Overvoltage* (Transient Overvoltage, tini = 10 sec) Safety Limiting Values (Maximum values allowed in the event of a failure, also see Figure 9, Thermal Derating curve.) Case Temperature Input Current Output Power Insulation Resistance at TS, VIO = 500 V Symbol Characteristic Units VIORM I-IV I-III 55/100/21 2 630 V peak VPR 1181 V peak VPR 945 V peak VIOTM 6000 V peak TS IS,INPUT PS,OUTPUT RS 175 230 600 ≥ 109 °C mA mW Ω IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics (HCNW135/6, HCNW4502/3 ONLY) Description Installation classification per DIN VDE 0110/1.89, Table 1 for rated mains voltage ≤ 600 V rms for rated mains voltage ≤ 1000 V rms Climatic Classification Pollution Degree (DIN VDE 0110/1.89) Maximum Working Insulation Voltage Input to Output Test Voltage, Method b* VIORM x 1.875 = VPR, 100% Production Test with tm = 1 sec, Partial Discharge < 5 pC Input to Output Test Voltage, Method a* VIORM x 1.5 = VPR, Type and sample test, tm = 60 sec, Partial Discharge < 5 pC Highest Allowable Overvoltage* (Transient Overvoltage, tini = 10 sec) Safety Limiting Values (Maximum values allowed in the event of a failure, also see Figure 9, Thermal Derating curve.) Case Temperature Input Current Output Power Insulation Resistance at TS, VIO = 500 V Symbol Characteristic Units VIORM I-IV I-III 55/85/21 2 1414 V peak VPR 2652 V peak VPR 2121 V peak VIOTM 8000 V peak TS IS,INPUT PS,OUTPUT RS 150 400 700 ≥ 109 °C mA mW Ω *Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section IEC/EN/DIN EN 60747-5-2, for a detailed description. Note: Isolation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in application. 8 Absolute Maximum Ratings Parameter Storage Temperature* Operating Temperature* Average Forward Input Current* Peak Forward Input Current* (50% duty cycle, 1 ms pulse width) (50% duty cycle, 1 ms pulse width) Peak Transient Input Current* (≤ 1 µs pulse width, 300 pps) Symbol TS TA IF(AVG) IF(PEAK) IF(TRANS) Reverse LED Input Voltage* (Pin 3-2) VR Input Power Dissipation* PIN Average Output Current* (Pin 6) Peak Output Current* Emitter-Base Reverse Voltage* (Pin 5-7, except 4502/3, 0452/3) Supply Voltage (Pin 8-5) Output Voltage (Pin 6-5) Supply Voltage* (Pin 8-5) Output Voltage* (Pin 6-5) Base Current* (Pin 7, except 4502/3, 0452/3) Output Power Dissipation* Lead Solder Temperature* (Through-Hole Parts Only) 1.6 mm below seating plane, 10 seconds up to seating plane, 10 seconds Reflow Temperature Profile *Data has been registered with JEDEC for the 6N135/6N136. Device 8-Pin DIP SO-8 Widebody Min. -55 -55 Max. 125 100 Units °C °C Note -55 85 25 mA 1 2 8-Pin DIP SO-8 Widebody 8-Pin DIP SO-8 Widebody 8-Pin DIP SO-8 Widebody 8-Pin DIP SO-8 Widebody 50 40 1 IO(AVG) IO(PEAK) VEBR VCC VO VCC VO IB PO TLS TRP -0.5 -0.5 -0.5 -0.5 8-Pin DIP Widebody SO-8 and Option 300 mA A 0.1 5 V 3 45 mW 40 8 16 5 mA mA V 30 20 15 15 5 100 V V V V mA mW 260 °C 260 °C See Package Outline Drawings section 3 4 9 Electrical Specifications (DC) Over recommended temperature (TA = 0°C to 70°C) unless otherwise specified. See note 13. Parameter Current Transfer Ratio Logic Low Output Voltage Symbol CTR* VOL Device 6N135 HCPL-0500 HCNW135 HCPL-2502 6N136 HCPL-4502/3 HCPL-0501 HCPL-0452/3 HCNW136 HCNW4502/3 6N135 HCPL-0500 HCNW135 6N136 HCPL-2502 HCPL-4502/3 HCPL-0501 HCPL-0452/3 HCNW136 HCNW4502/3 Min. Typ.** 7 18 5 15 15 19 19 15 25 22 25 24 0.1 0.1 0.5 0.4 IO = 0.8 mA TA = 25°C IO = 3.0 mA 0.1 0.5 IO = 2.4 mA 0.5 1 50 200 µA 1 2 1.7 1.8 1.85 1.95 µA 0.003 0.01 Logic Low Supply Current Logic High Supply Current Input Forward Voltage ICCL 50 ICCH* 0.02 Input Reverse Breakdown Voltage Temperature Coefficient of Forward Voltage Input Capacitance Transistor DC Current Gain BVR* ∆VF/ ∆TA CIN hFE *For JEDEC registered parts. **All typicals at TA = 25°C. 8-Pin DIP SO-8 Widebody 8-Pin DIP SO-8 Widebody 8-Pin DIP SO-8 Widebody 8-Pin DIP SO-8 Widebody 1.5 1.45 1.35 5 1.68 V µA V -1.6 -1.9 60 90 150 130 180 160 TA = 25°C IO = 1.1 mA Note 5, 11 TA = 25°C IF = 16 mA, VO = Open, VCC = 15 V TA = 25°C IF = 16 mA IR = 10 µA IR = 100 µA mV/°C IF = 16 mA pF IF = 16 mA, VCC = 4.5 V TA = 25°C VO = VCC = 5.5 V IF = 0 mA TA = 25°C VO = VCC = 15 V VO = VCC = 15 V IF = 16 mA, VO = Open, VCC = 15 V TA = 25°C IF = 16 mA V 3 Fig. 1, 2, 4 VO = 0.5 V 0.4 IOH* 8-Pin DIP SO-8 Widebody 50 Units Test Conditions % TA = 25°C VO = 0.4 V IF = 16 mA, VCC = 4.5 V VO = 0.5 V TA = 25°C VO = 0.4 V VO = 0.5 V TA = 25°C VO = 0.4 V 0.1 Logic High Output Current VF* Max. 50 f = 1 MHz, VF = 0 V VO = 5 V, IO = 3 mA VO = 0.4 V, IB = 20 µA VO = 5 V, IO = 3 mA VO = 0.4 V, IB = 20 µA 7 13 13 3 10 Switching Specifications (AC) Over recommended temperature (TA = 0°C to 70°C), VCC = 5 V, IF = 16 mA unless otherwise specified. Parameter Propagation Delay Time to Logic Low at Output Propagation Delay Time to Logic High at Output Common Mode Transient Immunity at Logic High Level Output Common Mode Transient Immunity at Logic Low Level Output Bandwidth Sym. tPHL* Device Min. Typ.** Max. 6N135 0.2 1.5 HCPL-0500 2.0 HCNW135 6N136 0.2 0.8 HCPL-2502 HCPL-4502/3 HCPL-0501 HCPL-0452/3 1.0 HCNW136 HCNW4502/3 6N135 1.3 1.5 tPLH* HCPL-0500 2.0 HCNW135 6N136 0.6 0.8 HCPL-2502 HCPL-4502/3 HCPL-0501 HCPL-0452/3 1.0 HCNW136 HCNW4502/3 6N135 1 |CMH| HCPL-0500 HCNW135 6N136 1 HCPL-2502 HCPL-4502 HCPL-0501 HCPL-0452 HCNW4502 HCPL-4503 15 30 HCPL-0453 HCNW4503 6N135 1 |CML| HCPL-0500 HCNW135 6N136 1 HCPL-2502 HCPL-4502 HCPL-0501 HCPL-0452 HCNW4502 HCPL-4503 15 30 HCPL-0453 HCNW4503 BW 6N135/6 9 HCPL-2502 HCPL-0500/1 HCNW135/6 11 *For JEDEC registered parts. **All typicals at TA = 25°C. Units Test Conditions µs TA = 25°C RL = 4.1 kΩ µs TA = 25°C RL = 1.9 kΩ TA = 25°C RL = 4.1 kΩ TA = 25°C RL = 1.9 kΩ kV/µs RL = 4.1 kΩ IF = 0 mA, TA = 25°C, VCM = 10 Vp-p CL = 15 pF RL = 1.9 kΩ RL = 1.9 kΩ IF = 0 mA, TA = 25°C, VCM = 1500 Vp-p, CL = 15 pF kV/µs RL = 4.1 kΩ IF = 16 mA, TA = 25°C, VCM = 10 Vp-p CL = 15 pF RL = 1.9 kΩ MHz RL = 1.9 kΩ IF = 16 mA, TA = 25°C, VCM = 1500 Vp-p, CL = 15 pF See Test Circuit Fig. 5, 6, 11 Note 8, 9 5, 6, 11 8, 9 12 7, 8, 9 12 7, 8, 9 8, 10 10 11 Package Characteristics Over recommended temperature (TA = 0°C to 70°C) unless otherwise specified. Parameter Input-Output Momentary Withstand Voltage** Sym. VISO II-O Input-Output Resistance Input-Output Capacitance RI-O CI-O Device 8-Pin DIP SO-8 Widebody 8-Pin DIP (Option 020) 8-Pin DIP 8-Pin DIP SO-8 Widebody 8-Pin DIP SO-8 Widebody Min. Typ.* 3750 Max. Units V rms 5000 Test Conditions RH < 50%, t = 1 min., TA = 25°C 5000 1 1012 1012 1011 µA Ω 45% RH, t = 5 s, VI-O = 3 kVdc, TA = 25°C VI-O = 500 Vdc pF TA = 25°C TA = 100°C f = 1 MHz 1013 0.6 0.5 Fig. Note 6, 14 6, 15 6, 12, 15 6, 16 6 6 0.6 *All typicals at TA = 25°C. **The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics Table (if applicable), your equipment level safety specification or Agilent Application Note 1074 entitled “Optocoupler Input-Output Endurance Voltage,” publication number 5963-2203E. Notes: 1. Derate linearly above 70°C free-air temperature at a rate of 0.8 mA/°C (8-Pin DIP). Derate linearly above 85°C free-air temperature at a rate of 0.5 mA/°C (SO-8). 2. Derate linearly above 70°C free-air temperature at a rate of 1.6 mA/°C (8-Pin DIP). Derate linearly above 85°C free-air temperature at a rate of 1.0 mA/°C (SO-8). 3. Derate linearly above 70°C free-air temperature at a rate of 0.9 mW/°C (8-Pin DIP). Derate linearly above 85°C free-air temperature at a rate of 1.1 mW/°C (SO-8). 4. Derate linearly above 70°C free-air temperature at a rate of 2.0 mW/°C (8-Pin DIP). Derate linearly above 85°C free-air temperature at a rate of 2.3 mW/°C (SO-8). 5. CURRENT TRANSFER RATIO in percent is defined as the ratio of output collector current, IO, to the forward LED input current, IF, times 100. 6. Device considered a two-terminal device: Pins 1, 2, 3, and 4 shorted together and Pins 5, 6, 7, and 8 shorted together. 7. Common mode transient immunity in a Logic High level is the maximum tolerable (positive) dVCM/dt on the leading edge of the common mode pulse signal, VCM, to assure that the output will remain in a Logic High state (i.e., VO > 2.0 V). Common mode transient immunity in a Logic Low level is the maximum tolerable (negative) dVCM /dt on the trailing edge of the common mode pulse signal, VCM, to assure that the output will remain in a Logic Low state (i.e., VO < 0.8 V). 8. The 1.9 kΩ load represents 1 TTL unit load of 1.6 mA and the 5.6 kΩ pull-up resistor. 9. The 4.1 kΩ load represents 1 LSTTL unit load of 0.36 mA and 6.1 kΩ pull-up resistor. 10. The frequency at which the ac output voltage is 3 dB below its mid-frequency value. 11. The JEDEC registration for the 6N136 specifies a minimum CTR of 15%. Agilent guarantees a minimum CTR of 19%. 12. See Option 020 data sheet for more information. 13. Use of a 0.1 µf bypass capacitor connected between pins 5 and 8 is recommended. 14. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 4500 V rms for 1 second (leakage detection current limit, II-O ≤ 5 µA). This test is performed before the 100% Production test shown in the IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics Table if applicable. 15. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 6000 V rms for 1 second (leakage detection current limit, II-O ≤ 5 µA). This test is performed before the 100% Production test shown in the IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics Table if applicable. 16. This rating is equally validated by an equivalent ac proof test. 12 WIDEBODY 16 40 mA T = 25°C 10 VA = 5.0 V CC 35 mA 30 mA 25 mA 5 TA = 25°C VCC = 5.0 V IO – OUTPUT CURRENT – mA IO – OUTPUT CURRENT – mA 8 PIN DIP, SO-8 20 mA 15 mA 10 mA 40 mA 12 35 mA 30 mA 25 mA 8 20 mA 15 mA 4 10 mA IF = 5 mA IF = 5 mA 0 0 0 10 20 0 10 VO – OUTPUT VOLTAGE – V 20 VO – OUTPUT VOLTAGE – V 8 PIN DIP, SO-8 1.5 6N135, HCPL-0500 6N136, HCPL-4502/3, HCPL-2502 HCPL-0501/0452/0453 1.0 0.5 NORMALIZED I F = 16 mA VO = 0.4 V VCC = 5 V TA = 25°C 0.1 0 1 10 100 WIDEBODY NORMALIZED CURRENT TRANSFER RATIO NORMALIZED CURRENT TRANSFER RATIO Figure 1. DC and Pulsed Transfer Characteristics. 1.5 HCNW135/6, HCNW4502/3 1.0 0.5 NORMALIZED IF = 16 mA VO = 0.4 V VCC = 4.5 V TA = 25 °C 0 0 1 IF – INPUT CURRENT – mA 10 100 IF – INPUT CURRENT – mA Figure 2. Current Transfer Ratio vs. Input Current. 8 PIN DIP, SO-8 WIDEBODY 1000 100 IF TA = 25°C + VF – 10 IF – FORWARD CURRENT – mA IF – FORWARD CURRENT – mA 1000 1.0 0.1 0.01 0.001 1.1 1.2 1.3 1.4 1.5 1.6 VF – FORWARD VOLTAGE – VOLTS Figure 3. Input Current vs. Forward Voltage. TA = 25° C 100 10 1.0 IF 0.1 + VF – 0.01 0.001 1.2 1.3 1.4 1.5 1.6 1.7 1.8 VF – FORWARD VOLTAGE – VOLTS 8 PIN DIP, SO-8 1.1 1.0 0.9 0.8 0.7 NORMALIZED IF = 16 mA VO = 0.4 V VCC = 5 V TA = 25°C 6N135, HCPL-0500 6N136, HCPL-4502/3, HCPL-2502 HCPL-0501, 0452, 0453 0.6 -60 -40 -20 0 20 40 60 80 100 WIDEBODY NORMALIZED CURRENT TRANSFER RATIO NORMALIZED CURRENT TRANSFER RATIO 13 1.1 1.0 HCNW135/6, HCNW4502/3 0.9 0.8 0.7 NORMALIZED IF = 16 mA VO = 0.4 V VCC = 5 V TA = 25°C 0.6 0.5 0.4 -60 -40 -20 TA – TEMPERATURE – °C 0 20 40 80 100 60 TA – TEMPERATURE – °C Figure 4. Current Transfer Ratio vs. Temperature. WIDEBODY 8 PIN DIP, SO-8 1500 IF = 16 mA, VCC = 5.0 V 6N135, HCPL-0500 (RL = 4.1 kΩ) 6N136, HCPL-0501, HCPL-2502 HCPL-4502/3 (RL = 1.9 kΩ) HCPL-0452/3 1000 tPLH tPHL 500 0 -60 20 -20 60 1000 tp – PROPAGATION DELAY – ns tp – PROPAGATION DELAY – ns 2000 IF = 16 mA, VCC = 5.0 V HCNW135 (RL = 4.1 kΩ) HCNW136 (RL = 1.9 kΩ) HCNW4502/3 800 600 tPLH tPHL 400 200 0 -60 -40 -20 100 0 20 40 60 80 100 TA – TEMPERATURE – °C TA – TEMPERATURE – °C Figure 5. Propagation Delay vs. Temperature. WIDEBODY 8 PIN DIP, SO-8 2.0 10.0 I F = 10 mA I F = 16 mA VCC = 5.0 V TA = 25 °C 1.0 0.8 0.6 tPLH 0.4 t PHL 0.2 0.1 1 2 3 4 5 6 7 8 9 10 RL – LOAD RESISTANCE – (kΩ) tP – PROPAGATION DELAY – µs tP – PROPAGATION DELAY – µs 3.0 I F = 10 mA I t = 16 mA 6.0 4.0 VCC = 5.0 V TA = 25 °C t PLH 1.0 0.6 t PHL 0.4 0.2 0.1 1 2 4 10 40 RL – LOAD RESISTANCE – (kΩ) Figure 6. Propagation Delay Time vs. Load Resistance. 100 8 PIN DIP, SO-8 10+4 IF = 0 VO = VCC = 5.0 V 10+3 10+2 10+1 100 10 -1 10 -2 -75 -50 -25 0 +25 +50 +75 +100 IOH – LOGIC HIGH OUTPUT CURRENT – nA IOH – LOGIC HIGH OUTPUT CURRENT – nA 14 WIDEBODY +3 10 IF = 0 VO = VCC = 15 V +2 10 +1 10 0 10 -60 -40 -20 0 20 40 60 80 100 TA – TEMPERATURE – °C TA – TEMPERATURE – °C 8 PIN DIP, SO-8 0.30 ∆ IO ∆ I F – SMALL SIGNAL CURRENT TRANSFER RATIO ∆ IO I∆ F– SMALL SIGNAL CURRENT TRANSFER RATIO Figure 7. Logic High Output Current vs. Temperature. WIDEBODY 0.50 TA = 25°C, RL = 100 Ω, VCC = 5 V TA = 25°C, RL = 100 Ω, VCC = 5 V 0.40 0.20 0.30 0.20 0.10 0.10 0 0 4 8 12 16 20 25 IF – QUIESCENT INPUT CURRENT – mA 0 0 4 8 12 16 20 25 IF – QUIESCENT INPUT CURRENT – mA HCPL-4503 OPTION 060 800 PS (mW) 700 IS (mA) 600 500 400 300 200 100 0 0 25 50 75 100 125 150 175 200 TS – CASE TEMPERATURE – °C OUTPUT POWER – PS, INPUT CURRENT – IS OUTPUT POWER – PS, INPUT CURRENT – IS Figure 8. Small-Signal Current Transfer Ratio vs. Quiescent Input Current. HCNW135/6, HCNW4502/3 1000 PS (mW) 900 IS (mA) 800 700 600 500 400 300 200 100 0 0 25 50 75 100 125 150 175 TS – CASE TEMPERATURE – °C Figure 9. Thermal Derating Curve, Dependence of Safety Limiting Value with Case Temperature per IEC/EN/DIN EN 60747-5-2. 15 6N135/6, HCPL-0500/1, HCPL-2502 6N135/6, HCPL-0500/1, HCPL-2502 +5 +12 V NORMALIZED RESPONSE - dB TA = 25 °C 1 0.1 µF 0 1.2 KΩ 0.1 µF 15 KΩ 2 7 Q3 9.1 KΩ -5 47 µF VFF 100 Ω 3 1N4150 1.0 10 5 22 Ω TRIM FOR UNITY GAIN 100 HCNW135/6 Figure 10. Frequency Response. Q 1 , Q 2 , Q 3 : 2N3904 TYPICAL LINEARITY = ± 3% AT V IN = 1 Vp-p TYPICAL SNR = 50dB TYPICAL R T = 375 Ω TYPICAL VO dc = 3.8 V TYPICAL I F = 9 mA f - FREQUENCY - MHz HCNW135/6 470 Ω 100 Ω RT 51 Ω VO Q2 0.1 µF 4 1 KΩ -15 6 Q1 -10 -20 0.1 +12 V 8 2.1 KΩ (1 MΩ 12 pF TEST INPUT) IF PULSE GEN. ZO = 50 Ω t r = 5 ns 0 IF 5V VO 10% DUTY CYCLE 1/f < 100 µS 1.5 V 1.5 V VOL 8 2 7 * 3 6 +5 V RL VO 0.1µF I F MONITOR 4 5 CL = 1.5 µF RM t PLH t PHL 1 * PIN 7 UNCONNECTED IN HCPL-4502/3, HCPL-0452/3, HCNW4502/3 Figure 11. Switching Test Circuit. IF 1 8 2 7 * 3 6 +5 V B VCM 0V 10% 90% 90% A 10% tr RL tf VO 0.1 µF VO 4 5V VO SWITCH AT B: I F = 16 mA 5 VFF SWITCH AT A: I F = 0 mA VOL VCM + – PULSE GEN. *PIN 7 UNCONNECTED IN HCPL-4502/3, HCPL-0542/3, HCNW4502/3 Figure 12. Test Circuit for Transient Immunity and Typical Waveforms. www.agilent.com/semiconductors For product information and a complete list of distributors, please go to our web site. For technical assistance call: Americas/Canada: +1 (800) 235-0312 or (916) 788-6763 Europe: +49 (0) 6441 92460 China: 10800 650 0017 Hong Kong: (+65) 6756 2394 India, Australia, New Zealand: (+65) 6755 1939 Japan: (+81 3) 3335-8152 (Domestic/International), or 0120-61-1280 (Domestic Only) Korea: (+65) 6755 1989 Singapore, Malaysia, Vietnam, Thailand, Philippines, Indonesia: (+65) 6755 2044 Taiwan: (+65) 6755 1843 Data subject to change. Copyright © 2004 Agilent Technologies, Inc. Obsoletes 5989-0305EN December 20, 2004 5989-2112EN