MIC HERF1601C High efficiency glass passivated rectifier Datasheet

HIGH EFFICIENCY GLASS PASSIVATED RECTIFIER
HERF1601C THRU HERF1607C
VOLTAGE RANGE
50 to 1000 Volts
CURRENT
16.0 Ampere
FEATURES
•
•
•
•
•
•
•
•
•
ITO-220AB
High speed switching
Glass passivated chip junction
Low power loss, high efficiency
Low leakage
High surge capacity
High temperature soldering guaranteed
250℃/10 second, 0.16″(4.06mm) lead length
Also available with common Anode, add an “A” suffix,
i.e. HERF1601CA, add as a doubler, add a “D” suffix,
i.e. HERF1601CD
Also available in an isolated package, HER1601C
Also available in the single chip version, HERF1601
MECHANICAL DATA
•
•
•
•
•
•
Dimensions in inches and (millimeters)
Case: Transfer molded plastic
Epoxy: UL94V-0 rate flame retardant
Lead: solderable per MIL-STD-202E method 208C
Polarity: as Marked
Mounting position: Any, 5 in-lbs Torque Max
Weight: 0.08ounce, 2.24 gram
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
•
•
•
Ratings at 25℃ ambient temperature unless otherwise specified
Single Phase, half wave, 60Hz, resistive or inductive load
For capacitive load derate current by 20%
HERF HERF
SYMBOLS
1601C 1602C
Maximum Repetitive Peak Reverse Voltage
VRRM
50
100
Maximum RMS Voltage
VRMS
35
70
Maximum DC Blocking Voltage
VDC
50
100
Maximum Average Forward Rectified Current
At Tc=100℃
Peak Forward Surge Current
8.3ms single half sine-wave superimposed on
rated load (JEDEC method)
HERF
1606C
600
420
600
HERF
1607C
800
560
800
UNIT
Volts
Volts
Volts
Amps
IFSM
125
Amps
Maximum DC Reverse Current at rated TA = 25℃
DC Blocking Voltage at
TA = 125℃
IR
Storage Temperature Range
HERF
1605C
400
280
400
16.0
VF
Operating Junction Temperature
HERF
1604C
300
210
300
I(AV)
Maximum Instantaneous Forward Voltage per at 8.0A
Maximum Reverse Recovery Time
Test conditions lF=0.5A, lR=1.0A, lRR=0.25A
Typical Junction Capacitance
(Measured at 1.0MHz and applied reverse voltage of 4.0V)
Typical Thermal Resistance (NOTE 1)
HERF
1603C
200
140
200
trr
1.0
1.3
1.5
1.7
10
500
70
Volts
µA
100
nS
CJ
40
pF
RθJC
TJ
TSTG
2.5
(-55 to +150)
(-55 to +150)
℃/W
Notes:
1. Unit mounted on heatsink
E-mail: [email protected]
Web Site: www.cnmic.com
℃
℃
HIGH EFFICIENCY GLASS PASSIVATED RECTIFIER
HERF1601C THRU HERF1607C
VOLTAGE RANGE
50 to 1000 Volts
CURRENT
16.0 Ampere
RATING AND CHRACTERISTIC CURVES HERF1601C THRU HERF1607C
FIG.2-MAXIMUM NON-REPETITIVE PEAK
FORWARD SURGE CURRENT
20
16
12
8.0
Single Phase
Half Wave 60Hz
Resistive or
Inductive Load
0.375″(9.5mm) Lead Length
4.0
150
CURRENT, (A)
PEAK FORWARD SURGE
24
(A)
AVERAGE FORWARD CURRENT,
FIG.1-TYPICAL FORWARD CURRENT
DERATING CURVE
8.3ms Single Half Sine-Wave
(JEDEC Method) T= Tjmax
100
50
1 Cycle
0
0
25
50
75
100
175
150
125
0
1
2
AMBIENT TEMPERATURE, (° C)
4
6
8
10
40
20
60
100
NUMBER OF CYCLES AT 60 Hz
FIG.4-TYPICAL REVERSE
CHARACTERISTICS PER LEG
FIG.3-TYPICAL INSTANTANEOUS
FORWARD CHARACTERISTICS PER LEG
0V
50
1.0
TJ =25° C
Pulse Width=300us
1% Duty Cycle
0.1
0.4
0.8
1.6
1.2
INSTANTANEOUS FORWARD VOLTAGE,(V)
10
(μA)
80
0/
INSTANTANEOUS REVERSE CURRENT,
/4
V
00
0/ 2
60
/10
30
0
10
00
V
TJ=125° C
(A)
INSTANTANEOUS FORWARD CURRENT,
100
100
1.0
TJ =25° C
0.1
0.01
FIG.5-TYPICAL JUNCTION CAPACITANCE
PER LEG
0
20
40
100
80
120
140
PERCENT OF RATED PEAK
100
JUNCTION CAPACITANCE,(pF)
60
REVERSE VOLTAGE,(%)
F1G.6-TEST CIRCUIT DIAGRAM AND
REVERSE RECOVERY TIME CHARACTERISTIC
Trr
50Ω
10Ω
NONINDUCTIVE NONINDUCTIVE
+0.5A
(-)
10
(+)
25 Vdc
(approx.)
(-)
T J =25° C
f=1MHz
Vsig=50mVp-p
1.0
1Ω
NON
INDUCTIVE
PULSE
GENERATIOR
(NOTE 2)
0
-0.25A
(+)
OSCILLOSCOPE
(NOTE 1)
-1.0A
1
0.1
D.U.T.
10
100
REVERSE VOLTAGE,(V)
E-mail: [email protected]
NOTES : 1.Rise Time=7ns mas. Input Impedance=
1 magohm. 22pF
2.Rise time=10ns max. Source Impedance=
50 ohms
Web Site: www.cnmic.com
1cm
SET TIME BASE FOR
50/100ns/cm
Similar pages