Bel A463-0080-02 5 tap leading edge control standard delay module Datasheet

defining a degree of excellence
5 TAP LEADING EDGE CONTROL
STANDARD DELAY MODULES
Cat 7-R7
.300
.300
7 2
bel
.375
.350
(DC)
(P/N)
.285 Max
Vcc 8
6 3
5
bel
(DC)
(P/N)
.325
*
.285 Max
In 1
.10 Typ
.10 Typ
Gnd 4
.50 Max
.50 Max
4o
.015
.004
.22 Max
.012
.008
.018
Coplanarity + .002
.012
.008
.030
SMD
Thru-Hole
Total
Delay
Delay
per Tap
S423-0025-02
S423-0030-02
S423-0035-02
S423-0040-02
S423-0045-02
A463-0025-02
A463-0030-02
A463-0035-02
A463-0040-02
A463-0045-02
25
30
35
40
45
5
6
7
8
9
S423-0050-02
A463-0050-02
50 ns
10 ns
3 ns
S423-0060-02
S423-0070-02
A463-0060-02
A463-0070-02
60 ns
70 ns
12 ns
14 ns
3 ns
3 ns
S423-0080-02
S423-0090-02
S423-0100-02
S423-0125-02
S423-0150-02
A463-0080-02
A463-0090-02
A463-0100-02
A463-0125-02
A463-0150-02
16
18
20
25
30
3
3
3
3
3
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Rise
Time
3
3
3
3
3
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Tolerances
Input to Taps + 2 ns or 5% , Whichever is Greater
Tap to Tap + 2 ns or 7% , Whichever is Greater
Delays measured @ 1.5 V levels on Leading Edge only
with no loads on Taps
Rise and Fall Times measured from 0.75 V to 2.4 V levels
Drive Capabilities
Nh Logic 1 Fanout
Nl Logic 0 Fanout
-
Temp.
100o C
0
2
.015 Min
.045
.018
4
6
Ti m e i n M i n u t e s
3.2 Volts
3.0 ns (10%-90%)
1.2 x Total Delay
4 x Pulse Width
35 ma Typical
5.0 Volts
Pulse Voltage
Rise Time
Pulse Width
Pulse Period
Supply Current
Supply Voltage
Electrical Characteristics
Min.
4.75
2.0
Max.
5.25
Units
V
V
V
ma
ma
V
V
V
ua
ma
ma
ma
ma
C
%
%
Vcc
Vih
Vil
Ioh
Iol
Voh
Vol
Vik
Iih
Iil
Ios
Icch
Iccl
Ta
PW
d
Supply Voltage
Logic 1 Input Voltage
Logic 0 Input Voltage
Logic 1 Output Current
Logic 0 Output Current
Logic 1 Output Voltage
Logic 0 Output voltage
Input Clamp Voltage
Logic 1 Input Current
Logic 0 Input Current
Short Circuit Output Current
Logic 1 Supply Current
Logic 0 Supply Current
Operating Free Air Temperature
Min. Input Pulse Width of Total Delay
Maximum Duty Cycle
Tc
Temp. Coeff. of Total Delay (TD) 100 + (25000/TD) PPM/OC
0.8
-1
20
2.7
-60
0o
40
0.5
-1.2
20
-0.6
-150
25
40
70o
50
Transfer molded for better reliability
Compatible with TTL & DTL circuits
Terminals: Electro-Tin plate phosphor bronze
Performance warranty is limited to specified parameters listed
SMD - Tape & Reel available:
24mm Wide x 12mm Pitch, 750 pieces per 13" reel
Infra Red
200 C
.12 Min
Notes
225o C Max Temp.
> 185o C
for 90 Seconds Max
o
Ein
Trin
PW
PP
Iccl
Vcc
20 TTL Loads Max.
10 TTL Loads Max.
Recommended Temperature Profile
300o C
100o
90o
Test Conditions @ 25oC
Part Numbers
80
90
100
125
150
.20 Max
.23 Max
8
Other Delays and Tolerances Available
Consult Sales
Specifications subject to change without notice.
Corporate Office
Bel Fuse Inc.
198 Van Vorst Street, Jersey City, NJ 07302-4496
Tel: 201-432-0463
Fax: 201-432-9542
E-Mail: [email protected]
Internet: http://www.belfuse.com
Far East Office
Bel Fuse Ltd.
8F/8 Luk Hop Street
San Po Kong
Kowloon, Hong Kong
Tel: 852-2328-5515
Fax: 852-2352-3706
European Office
Bel Fuse Europe Ltd.
Preston Technology Management Centre
Marsh Lane, Preston PR1 8UD
Lancashire, U.K.
Tel: 44-1772-556601
Fax: 44-1772-888366
5
Similar pages