LT4320/LT4320-1 Ideal Diode Bridge Controller Description Features n n n n n n n Maximizes Power Efficiency Eliminates Thermal Design Problems DC to 600Hz 9V to 72V Operating Voltage Range IQ = 1.5mA (Typical) Maximizes Available Voltage Available in 8-Lead (3mm × 3mm) DFN, 12-Lead MSOP and 8-Lead PDIP Packages The LT®4320/LT4320-1 are ideal diode bridge controllers that drive four N-channel MOSFETs, supporting voltage rectification from DC to 600Hz typical. By maximizing available voltage and reducing power dissipation (see thermograph comparison below), the ideal diode bridge simplifies power supply design and reduces power supply cost, especially in low voltage applications. Applications n n n n n Security Cameras Terrestrial or Airborne Power Distribution Systems Power-over-Ethernet Powered Device with a Secondary Input Polarity-Agnostic Power Input Diode Bridge Replacement L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. Patent pending. Typical Application An ideal diode bridge also eliminates thermal design problems, costly heat sinks, and greatly reduces PC board area. The LT4320’s internal charge pump supports an allNMOS design, which eliminates larger and more costly PMOS switches. If the power source fails or is shorted, a fast turn-off minimizes reverse current transients. The LT4320 is designed for DC to 60Hz typical voltage rectification, while the LT4320-1 is designed for DC to 600Hz typical voltage rectification. Higher frequencies of operation are possible depending on MOSFET size and operating load current. Thermograph of Passive Diode Bridge + Temperature Rise TG1 ~ OUTP MOSFET CURRENT 2.5mΩ TG2 LT4320 IN1 IN2 BG2 BG1 OUTN OUTPUT 9V TO 72V SBM1040 (×4) 4320 TA01b Thermograph of LT4320 Driving Four MOSFETs INPUT DC TO 600Hz (TYP) 2A 0.6°C 15°C 4A 3.5°C 32°C 6A 6.7°C 49°C 8A 11°C 66°C 10A 16°C 84°C DC Input, On Same PCB – ~ DIODE SBM 1040 4320 TA01a 4320 TA01c LT4320+2.5mΩ FET (×4) CONDITIONS: 24V ACIN, 9.75A DC LOAD ON SAME PCB For more information www.linear.com/LT4320 4320fb 1 LT4320/LT4320-1 Absolute Maximum Ratings (Notes 1, 2) Supply Voltages IN1, IN2..................................................... –3V to 80V OUTP...................................................... –0.3V to 80V Output Voltages (Note 3) BG1, BG2, TG1, TG2................................ –0.3V to 80V TG1-IN1, TG2-IN2.....................................–0.3V to 12V Operating Junction Temperature Range LT4320I.................................................–40°C to 85°C LT4320H............................................. –40°C to 125°C LT4320MP.......................................... –55°C to 125°C Storage Temperature Range................... –65°C to 150°C Lead Temperature (Soldering, 10 sec) MSE, PDIP Packages......................................... 300°C Pin Configuration TOP VIEW TOP VIEW IN2 1 TG2 2 BG2 3 9 BG1 4 8 IN1 7 TG1 6 OUTP 5 OUTN DD PACKAGE 8-LEAD (3mm × 3mm) PLASTIC DFN TJMAX = 150°C, θJC = 5.5°C/W EXPOSED PAD (PIN 9) MUST BE CONNECTED TO OUTN (PIN 5) IN2 TG2 NC NC BG2 BG1 1 2 3 4 5 6 13 12 11 10 9 8 7 IN1 TG1 NC OUTP NC OUTN TOP VIEW IN2 1 8 IN1 TG2 2 7 TG1 BG2 3 6 OUTP BG1 4 5 OUTN MSE PACKAGE 12-LEAD PLASTIC MSOP TJMAX = 150°C, θJC = 10°C/W EXPOSED PAD (PIN 13) MUST BE CONNECTED TO OUTN (PIN 7) N8 PACKAGE 8-LEAD PLASTIC DIP TJMAX = 150°C, θJC = 45°C/W Order Information LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION OPERATING JUNCTION TEMPERATURE RANGE LT4320IDD#PBF LT4320IDD#TRPBF LGCV 8-Lead (3mm × 3mm) Plastic DFN –40°C to 85°C LT4320HDD#PBF LT4320HDD#TRPBF LGCV 8-Lead (3mm × 3mm) Plastic DFN –40°C to 125°C LT4320IDD-1#PBF LT4320IDD-1#TRPBF LGCW 8-Lead (3mm × 3mm) Plastic DFN –40°C to 85°C LT4320HDD-1#PBF LT4320HDD-1#TRPBF LGCW 8-Lead (3mm × 3mm) Plastic DFN –40°C to 125°C LT4320IMSE#PBF LT4320IMSE#TRPBF 4320 12-Lead Plastic MSOP –40°C to 85°C LT4320HMSE#PBF LT4320HMSE#TRPBF 4320 12-Lead Plastic MSOP –40°C to 125°C LT4320MPMSE#PBF LT4320MPMSE#TRPBF 4320 12-Lead Plastic MSOP –55°C to 125°C LT4320IMSE-1#PBF LT4320IMSE-1#TRPBF 43201 12-Lead Plastic MSOP –40°C to 85°C LT4320HMSE-1#PBF LT4320HMSE-1#TRPBF 43201 12-Lead Plastic MSOP –40°C to 125°C LT4320MPMSE-1#PBF LT4320MPMSE-1#TRPBF 43201 12-Lead Plastic MSOP –55°C to 125°C LT4320IN8#PBF NA LT4320N8 8-Lead PDIP –40°C to 85°C LT4320HN8#PBF NA LT4320N8 8-Lead PDIP –40°C to 125°C LT4320IN8-1#PBF NA LT4320N8-1 8-Lead PDIP –40°C to 85°C LT4320HN8-1#PBF NA LT4320N8-1 8-Lead PDIP –40°C to 125°C Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. Consult LTC Marketing for information on nonstandard lead based finish parts. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ 4320fb 2 For more information www.linear.com/LT4320 LT4320/LT4320-1 Electrical Characteristics The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. (Note 2) SYMBOL PARAMETER CONDITIONS OUTP Voltage Range MIN l 9 OUTP Undervoltage Lockout (UVLO) Threshold INn = OUTP, Other IN = 0V l 6.2 VINT INn Turn-On/Off Threshold OUTP = 9V, Other IN = 0V l 1.3 IOUTP OUTP Pin Current INn = OUTP+ ∆VSD(MAX) + 5mV, Other IN = 0V l IINn INn Pin Current at 9V at 72V INn = OUTP+ ∆VSD(MAX) + 5mV, Other IN = 0V ∆VSD Topside Source-Drain Regulation Voltage (INn – OUTP) LT4320 LT4320-1 ∆VTGATE Top Gate Drive (TGn – INn) VBGATE l l TYP MAX UNITS 72 V 6.6 7.0 V 3.7 V 1.0 1.5 mA 44 0.3 63 0.4 µA mA 20 40 35 55 mV mV l l 8 26 INn = OUTP+ ∆VSD(MAX) + 5mV, 10μA Out of TGn, Other IN = 0V l 6.6 10.8 V Bottom Gate Drive (BGn) INn = OUTP, 10μA Out of BGn, Other IN = 0V l 7.0 12 V ITGUn Top Gate Pull-Up Current TGn – INn = 0V, INn = OUTP + 0.1V TGn – INn = 5V, INn = OUTP + 0.1V Current Flows Out of TGn, Other IN = 0V l l 425 120 µA µA ITGSn Top Gate Pull-Down Current to INn TGn – INn = 5V, INn = OUTP – 0.25V Current Flows Into TGn, Other IN = 0V l 1.25 mA ITGGn Top Gate Pull-Down Current to OUTN INn = 0V, Other IN = OUTP = 9.0V, TGn = 5V Current Flows Into TGn l 6.0 mA IBGUn Bottom Gate Pull-Up Current BGn = 5V; INn = OUTP = 9.0V, Other IN = 0V Current Flows Out of BGn l 1.9 mA IBGDn Bottom Gate Pull-Down Current BGn = 5V; INn = 0V, Other IN = OUTP = 9.0V Current Flows Into BGn l 12.5 mA Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Unless otherwise specified, exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: All voltages are referenced to OUTN = 0V unless otherwise specified. Note 3: Externally forced voltage absolute maximums. The LT4320 may exceed these limits during normal operation. 4320fb For more information www.linear.com/LT4320 3 LT4320/LT4320-1 Typical Performance Characteristics IINn and IOUTP vs OUTP OTHER IN = 0V OUTP 800 IN1 AND IN2 FLOATING 400 600 INn 0 20 40 INn = OUTP (V) 60 0 80 0 20 40 OUTP (V) 60 VBGATE vs OUTP 21 25 4320 G03 TGn Pull-Down Strength to INn 5 INn = OUTP + 100mV OTHER IN = 0V 900 800 INn = OUTP – 250mV OTHER IN = 0V 4 700 9 8 600 ITGSn (mA) ITGn (µA) VBGATE (V) 17 13 9 OUTP (V) TGn Pull-Up Strength 1000 10 500 400 3 2 300 200 7 OTHER IN = 0V 9 13 17 OUTP (V) 21 0 25 1 OUTP = 9V OUTP = 12V OUTP = 72V 100 2 0 6 4 8 0 2 4 6 8 ∆VTGATE (V) 10 BGn Pull-Up Strength 5 12 4320 G06 4320 G05 INn = 0V OTHER IN = OUTP 50 OUTP = 9V OUTP = 72V ∆VTGATE (V) TGn Pull-Down Strength to OUTN 60 0 12 10 4320 G04 BGn Pull-Down Strength 35 OTHER IN = 0V 30 4 25 30 3 IBGDn (mA) IBGUn (mA) 40 ITGGn (mA) 6 80 ∆VSD = 100mV ∆VSD = 40mV 4320 G02 11 2 20 20 15 10 OUTP = 9V OUTP = 12V OUTP = 72V 10 0 8 7 200 4320 G01 6 9 400 200 12 OTHER IN = 0V 10 800 600 0 11 1000 IOUTP (µA) CURRENT (µA) 1000 ∆VTGATE vs OUTP IOUTP vs OUTP 1200 ∆VTGATE (V) 1200 0 2 4 6 TGn (V) 8 10 12 4320 G07 1 0 VINn = 9V VINn = 12V VINn = 72V 0 2 4 8 VBGATE (V) 6 5 10 12 14 4320 G08 0 0 2 4 8 6 VBGATE (V) 10 12 4320 G09 4320fb 4 For more information www.linear.com/LT4320 LT4320/LT4320-1 Pin Functions (DFN, PDIP/MSOP) IN2 (Pin 1/Pin 1): Bridge Rectifier Input. IN2 connects to the external NMOS transistors MTG2 source, MBG1 drain and the power input. OUTP (Pin 6/Pin 9): OUTP is the rectified positive output voltage that powers the LT4320 and connects to the drains of MTG1 and MTG2. TG2 (Pin 2/Pin 2): Topside Gate Driver Output. TG2 pin drives MTG2 gate. TG1 (Pin 7/Pin 11): Topside Gate Driver Output. TG1 pin drives MTG1 gate. BG2 (Pin 3/Pin 5): Bottom-Side Gate Driver Output. BG2 pin drives MBG2 gate. IN1 (Pin 8/Pin 12): Bridge Rectifier Input. IN1 connects to the external NMOS transistors MTG1 source, MBG2 drain, and the power input. BG1 (Pin 4/Pin 6): Bottom-Side Gate Driver Output. BG1 pin drives MBG1 gate. OUTN (Pin 5/Pin 7): OUTN is the rectified negative output voltage, and connects to the sources of MBG1 and MBG2. NC (Pins 3, 4, 8, 10, MSOP Only): No Connections. Not internally connected. Exposed Pad (Pin 9/Pin 13): Exposed Pad, DFN and MSOP. Must be connected to OUTN. Block Diagram MTG1 ~ + MTG2 TG2 TG1 OUTP IN1 IN2 LT4320 CONTROL OUTN BG2 ~ BG1 MBG2 MBG1 LT4320 BD – 4320fb For more information www.linear.com/LT4320 5 LT4320/LT4320-1 Operation Electronic systems that receive power from an AC power source or a DC polarity-agnostic power source often employ a 4-diode rectifier. The traditional diode bridge comes with an efficiency loss due to the voltage drop generated across two conducting diodes. The voltage drop reduces the available supply voltage and dissipates significant power especially in low voltage applications. bridge also eliminates thermal design problems, costly heat sinks, and greatly reduces PC board area. The LT4320 is designed for DC to 60Hz typical voltage rectification, while the LT4320-1 is designed for DC to 600Hz typical voltage rectification. Higher frequencies of operation are possible depending on MOSFET size and operating load current. By maximizing available voltage and reducing power dissipation, the ideal diode bridge simplifies power supply design and reduces power supply cost. An ideal diode Figure 2 presents sample waveforms illustrating the gate pins in an AC voltage rectification design. MTG1 ~ + MTG2 INPUT TG2 TO LOAD TG1 IN1 OUTP CLOAD LT4320 OUTN IN2 BG2 BG1 MBG2 ~ MBG1 – 4320 F01 Figure 1. LT4320 with Four N-Channel MOSFETS, Illustrating Current Flow When IN1 Is Positive 40V 30V 20V 10V 0V VTG1 VTG2 VBG1 VBG2 VIN1 VOUTP VIN2 4320 F02 Figure 2. 24V AC Sample Waveform 4320fb 6 For more information www.linear.com/LT4320 LT4320/LT4320-1 Applications Information MOSFET Selection A good starting point is to reduce the voltage drop of the ideal bridge to 30mV per MOSFET with the LT4320 (50mV per MOSFET with the LT4320-1). Given the average output load current, IAVG, select RDS(ON) to be: RDS(ON) = 30mV for a DC power input IAVG RDS(ON) = 30mV for an AC power input 3 •IAVG or the maximum operating frequency, creates unintended efficiency losses, adversely increases turn-on/turn-off times, and increases the total solution cost. The LT4320 gate pull-up/pull-down current strengths specified in the Electrical Characteristics section, and the MOSFET total gate charge (Qg), determine the MOSFET turn-on/off times and the maximum operating frequency in an AC application. Choosing the lowest gate capacitance while meeting RDS(ON) speeds up the response time for full enhancement, regulation, turn-off and input shorting events. In the AC power input calculation, 3 • IAVG assumes the duration of current conduction occupies 1/3 of the AC period. VGS(th) must be a minimum of 2V or higher. A gate threshold voltage lower than 2V is not recommended since too much time is needed to discharge the gate below the threshold and halt current conduction during a hot plug or input short event. Select the maximum allowable drain-source voltage, VDSS, to be higher than the maximum input voltage. CLOAD Selection Design Example For a 24W, 12V DC/24V AC application, IAVG = 2A for 12V DC. To cover the 12V DC case: RDS(ON) = 30mV = 15mΩ 2A For the 24V AC operation, IAVG = 1A. To cover the 24V AC case: RDS(ON) = 30mV = 10mΩ 3 • 1A This provides a starting range of RDS(ON) values to choose from. Ensure the MOSFET can handle a continuous current of 3 • IAVG to cover the expected peak currents during AC rectification. That is, select ID ≥ 3A. Since a 24V AC waveform can reach 34V peak, select a MOSFET with VDSS >>34V. A good choice of VDSS is 60V in a 24V AC application. Other Considerations in MOSFET Selection Practical MOSFET considerations for the LT4320-based ideal bridge application include selecting the lowest available total gate charge (Qg) for the desired RDS(ON). Avoid oversizing the MOSFET, since an oversized MOSFET limits A 1μF ceramic and a 10μF minimum electrolytic capacitor must be placed across the OUTP and OUTN pins with the 1µF ceramic placed as close to the LT4320 as possible. Downstream power needs and voltage ripple tolerance determine how much additional capacitance between OUTP and OUTN is required. CLOAD in the hundreds to thousands of microfarads is common. A good starting point is selecting CLOAD such that: CLOAD ≥ IAVG/(VRIPPLE • 2 • Freq) where IAVG is the average output load current, VRIPPLE is the maximum tolerable output ripple voltage, and Freq is the frequency of the input AC source. For example, in a 60Hz, 24VAC application where the load current is 1A and the tolerable ripple is 15V, choose CLOAD ≥ 1A/(15V • 2 • 60Hz) = 556µF. CLOAD must also be selected so that the rectified output voltage, OUTP-OUTN, must be within the LT4320/LT4320-1 specified OUTP voltage range. Transient Voltage Suppressor For applications that may encounter brief overvoltage events higher than the LT4320 absolute maximum rating, install a unidirectional transient voltage suppressor (TVS) between the OUTP and OUTN pins as close as possible to the LT4320. 4320fb For more information www.linear.com/LT4320 7 LT4320/LT4320-1 Typical Applications B360B 4 COMPACT FETs* CONDITION: 13VDCIN, 3A LOAD ON SAME PCB *19mΩ, 60V EACH FET Figure 3. Thermograph: B360B vs LT4320 +4 Compact FETs 4320fb 8 For more information www.linear.com/LT4320 LT4320/LT4320-1 Typical Applications Figure 4. Demonstration Circuit 1902A Used in Figure 3 Thermograph 4320fb For more information www.linear.com/LT4320 9 LT4320/LT4320-1 Package Description Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings. DD Package 8-Lead Plastic DFN (3mm × 3mm) (Reference LTC DWG # 05-08-1698 Rev C) 0.70 ±0.05 3.5 ±0.05 1.65 ±0.05 2.10 ±0.05 (2 SIDES) PACKAGE OUTLINE 0.25 ±0.05 0.50 BSC 2.38 ±0.05 RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED PIN 1 TOP MARK (NOTE 6) 0.200 REF 3.00 ±0.10 (4 SIDES) R = 0.125 TYP 5 0.40 ±0.10 8 1.65 ±0.10 (2 SIDES) 0.75 ±0.05 4 0.25 ±0.05 1 (DD8) DFN 0509 REV C 0.50 BSC 2.38 ±0.10 0.00 – 0.05 BOTTOM VIEW—EXPOSED PAD NOTE: 1. DRAWING TO BE MADE A JEDEC PACKAGE OUTLINE M0-229 VARIATION OF (WEED-1) 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON TOP AND BOTTOM OF PACKAGE 4320fb 10 For more information www.linear.com/LT4320 LT4320/LT4320-1 Package Description Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings. MSE Package 12-Lead Plastic MSOP, Exposed Die Pad (Reference LTC DWG # 05-08-1666 Rev G) BOTTOM VIEW OF EXPOSED PAD OPTION 2.845 ±0.102 (.112 ±.004) 5.10 (.201) MIN 2.845 ±0.102 (.112 ±.004) 0.889 ±0.127 (.035 ±.005) 6 1 1.651 ±0.102 (.065 ±.004) 1.651 ±0.102 3.20 – 3.45 (.065 ±.004) (.126 – .136) 12 0.65 0.42 ±0.038 (.0256) (.0165 ±.0015) BSC TYP RECOMMENDED SOLDER PAD LAYOUT 0.254 (.010) 0.35 REF 4.039 ±0.102 (.159 ±.004) (NOTE 3) 0.12 REF DETAIL “B” CORNER TAIL IS PART OF DETAIL “B” THE LEADFRAME FEATURE. FOR REFERENCE ONLY 7 NO MEASUREMENT PURPOSE 0.406 ±0.076 (.016 ±.003) REF 12 11 10 9 8 7 DETAIL “A” 0° – 6° TYP 3.00 ±0.102 (.118 ±.004) (NOTE 4) 4.90 ±0.152 (.193 ±.006) GAUGE PLANE 0.53 ±0.152 (.021 ±.006) DETAIL “A” 1.10 (.043) MAX 0.18 (.007) SEATING PLANE 0.22 – 0.38 (.009 – .015) TYP 1 2 3 4 5 6 0.650 (.0256) BSC NOTE: 1. DIMENSIONS IN MILLIMETER/(INCH) 2. DRAWING NOT TO SCALE 3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS. INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX 6. EXPOSED PAD DIMENSION DOES INCLUDE MOLD FLASH. MOLD FLASH ON E-PAD SHALL NOT EXCEED 0.254mm (.010") PER SIDE. 0.86 (.034) REF 0.1016 ±0.0508 (.004 ±.002) MSOP (MSE12) 0213 REV G 4320fb For more information www.linear.com/LT4320 11 LT4320/LT4320-1 Package Description Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings. N Package 8-Lead PDIP (Narrow .300 Inch) (Reference LTC DWG # 05-08-1510 Rev I) .400* (10.160) MAX 8 7 6 5 1 2 3 4 .255 ±.015* (6.477 ±0.381) .300 – .325 (7.620 – 8.255) .008 – .015 (0.203 – 0.381) ( +.035 .325 –.015 8.255 +0.889 –0.381 ) .045 – .065 (1.143 – 1.651) .065 (1.651) TYP .100 (2.54) BSC .130 ±.005 (3.302 ±0.127) .120 (3.048) .020 MIN (0.508) MIN .018 ±.003 N8 REV I 0711 (0.457 ±0.076) NOTE: 1. DIMENSIONS ARE INCHES MILLIMETERS *THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .010 INCH (0.254mm) 4320fb 12 For more information www.linear.com/LT4320 LT4320/LT4320-1 Revision History REV DATE DESCRIPTION A 11/13 Clarified that input frequency ranges use typical numbers (60Hz, 600Hz) 1, 6 Added PDIP package 2, 12 B 2/14 PAGE NUMBER Reduced MOSFET drop to 30mV from 70mV in “MOSFET Selection” and “Design Example” sections 7 Provided additional guidance in “Other Considerations in MOSFET Selection” section 7 Updated MSE package drawing 10 Added H- and MP-grade information 2 4320fb Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. For more information www.linear.com/LT4320 13 LT4320/LT4320-1 Typical Application MTG1 ~ + MTG2 DIODE BRIDGE LT4320 IDEAL BRIDGE TG2 IN1 INPUT OUTP 1µF LT4320 IN2 MTG1,MTG2 MBG1, MBG2 TG1 + C1 TO LOAD BSZ110N06NS3 OUTN BG2 BG1 BSC031N06NS3 PSMN040-100MSE OPERATING VOLTAGE LOAD CURRENT C1 (MIN) POWER LOSS POWER LOSS 55V DC 3.5A 10µF 0.22W 4.2W 24V AC 1.5A 560µF 0.13W 1.9W 55V DC 30A 10µF 4.5W 36W 24V AC 10A 3.3mF 1.6W 12W 72V DC 2A 10µF 0.24W 2.4W MBG2 ~ MBG1 4320 TA02 – Related Parts PART NUMBER DESCRIPTION COMMENTS LT4321 PoE Ideal Diode Bridge Controller Replaces 8 Diodes with 8 N-Channel MOSFETs, Reduces Heat, Maximizes Efficiency LTC4352 Low Voltage Ideal Diode Controller with Monitoring N-Channel, 0V to 18V, UV, OV, MSOP-12 and DFN-12 Packages LTC4353 Dual Low Voltage Ideal Diode Controller Dual N-Channel, 0V to 18V, MSOP-16 and DFN-16 Packages LTC4354 Negative Voltage Diode-OR Controller and Monitor Controls Two N-Channel MOSFETs, 1μs Turn-Off, –80V Operation LTC4355 Positive Voltage Diode-OR Controller and Monitor Controls Two N-Channel MOSFETs, 0.5μs Turn-Off, 9V to 80V Operation LTC4357 Positive High Voltage Ideal Diode Controller Controls Single N-Channel MOSFETs, 0.5μs Turn-Off, 9V to 80V Operation LTC4358 5A Ideal Diode Positive Voltage Ideal Diode with Integrated MOSFET, 9V to 26.5V Operation LTC4359 Ideal Diode Controller with Reverse Input Protection N-Channel, 4V to 80V, MSOP-8 and DFN-6 Packages LTC4370 2-Supply Diode-OR Current Balancing Controller Dual N-Channel, 0V to 18V, MSOP-16 and DFN-16 Packages LTC4415 Dual 4A ideal Diodes with Adjustable Current Limit 1.7V to 5.5V Operating Range 4320fb 14 Linear Technology Corporation 1630 McCarthy Blvd., Milpitas, CA 95035-7417 For more information www.linear.com/LT4320 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com/LT4320 LT 0214 REV B • PRINTED IN USA LINEAR TECHNOLOGY CORPORATION 2013