Cypress CY7C1527V18-200BZI 72-mbit ddr-ii sram 2-word burst architecture Datasheet

CY7C1516V18
CY7C1527V18
CY7C1518V18
CY7C1520V18
72-Mbit DDR-II SRAM 2-Word
Burst Architecture
Features
Functional Description
• 72-Mbit density (8M x 8, 8M x 9, 4M x 18, 2M x 36)
The CY7C1516V18, CY7C1527V18, CY7C1518V18, and
CY7C1520V18 are 1.8V Synchronous Pipelined SRAM
equipped with DDR-II architecture. The DDR-II consists of an
SRAM core with advanced synchronous peripheral circuitry
and a 1-bit burst counter. Addresses for Read and Write are
latched on alternate rising edges of the input (K) clock.Write
data is registered on the rising edges of both K and K. Read
data is driven on the rising edges of C and C if provided, or on
the rising edge of K and K if C/C are not provided. Each
address location is associated with two 8-bit words in the case
of CY7C1516V18 and two 9-bit words in the case of
CY7C1527V18 that burst sequentially into or out of the device.
The burst counter always starts with a “0” internally in the case
of CY7C1516V18 and CY7C1527V18. On CY7C1518V18 and
CY7C1520V18, the burst counter takes in the least significant
bit of the external address and bursts two 18-bit words in the
case of CY7C1518V18 and two 36-bit words in the case of
CY7C1520V18 sequentially into or out of the device.
• 300-MHz clock for high bandwidth
• 2-Word burst for reducing address bus frequency
• Double Data Rate (DDR) interfaces
(data transferred at 600 MHz) @ 300 MHz
• Two input clocks (K and K) for precise DDR timing
— SRAM uses rising edges only
• Two input clocks for output data (C and C) to minimize
clock-skew and flight-time mismatches
• Echo clocks (CQ and CQ) simplify data capture in
high-speed systems
• Synchronous internally self-timed writes
• 1.8V core power supply with HSTL inputs and outputs
• Variable drive HSTL output buffers
Asynchronous inputs include output impedance matching
input (ZQ). Synchronous data outputs (Q, sharing the same
physical pins as the data inputs D) are tightly matched to the
two output echo clocks CQ/CQ, eliminating the need for
separately capturing data from each individual DDR SRAM in
the system design. Output data clocks (C/C) enable maximum
system clocking and data synchronization flexibility.
• Expanded HSTL output voltage (1.4V–VDD)
• Available in 165-ball FBGA package (15 x 17 x 1.4 mm)
• Offered in both lead-free and non lead-free packages
• JTAG 1149.1 compatible test access port
• Delay Lock Loop (DLL) for accurate data placement
Configurations
All synchronous inputs pass through input registers controlled
by the K or K input clocks. All data outputs pass through output
registers controlled by the C or C (or K or K in a single clock
domain) input clocks. Writes are conducted with on-chip
synchronous self-timed write circuitry.
CY7C1516V18 – 8M x 8
CY7C1527V18 – 8M x 9
CY7C1518V18 – 4M x 18
CY7C1520V18 – 2M x 36
Selection Guide
300 MHz
278 MHz
250 MHz
200 MHz
167 MHz
Unit
Maximum Operating Frequency
300
278
250
200
167
MHz
Maximum Operating Current (x36)
900
860
800
700
650
mA
Cypress Semiconductor Corporation
Document #: 38-05563 Rev. *D
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised June 1, 2006
[+] Feedback
CY7C1516V18
CY7C1527V18
CY7C1518V18
CY7C1520V18
LD
K
K
CLK
Gen.
DOFF
Read Add. Decode
Address
Register
Write
Reg
4M x 8 Array
22
Write
Reg
4M x 8 Array
A(21: 0)
Write Add. Decode
Logic Block Diagram (CY7C1516V18)
8
Output
Logic
Control
R/W
C
C
Read Data Reg.
16
VREF
R/W
NWS[1 : 0]
CQ
8
Reg.
Control
Logic
8
Reg.
CQ
8
Reg.
DQ[7:0]
8
LD
K
K
DOFF
CLK
Gen.
Read Add. Decode
Address
Register
Write
Reg
4M x 9 Array
22
Write
Reg
4M x 9 Array
A(21:0)
Write Add. Decode
Logic Block Diagram (CY7C1527V18)
9
Output
Logic
Control
R/W
C
C
Read Data Reg.
VREF
R/W
BWS[0]
18
Control
Logic
CQ
9
Reg.
9
Reg.
9
Reg.
CQ
DQ[8: 0]
9
Document #: 38-05563 Rev. *D
Page 2 of 28
[+] Feedback
CY7C1516V18
CY7C1527V18
CY7C1518V18
CY7C1520V18
Logic Block Diagram (CY7C1518V18)
Burst
Logic
21
22
Write
Reg
Address
A(21:1) Register
Write Add. Decode
A(21: 0)
LD
K
K
CLK
Gen.
DOFF
Write
Reg
Read Add. Decode
A0
4M x 18 Array
18
Output
Logic
Control
R/W
C
C
Read Data Reg.
CQ
36
VREF
R/W
BWS[1: 0]
18
Reg.
Control
Logic
18
CQ
Reg.
Reg.
18
DQ[17: 0]
18
Logic Block Diagram (CY7C1520V18)
Burst
Logic
Address
A(20:1) Register
LD
K
K
DOFF
CLK
Gen.
Write Add. Decode
A(20:0)
Write
Reg
20
21
Write
Reg
Read Add. Decode
A0
2M x 36 Array
36
R/W
Output
Logic
Control
C
C
Read Data Reg.
VREF
R/W
BWS[3:0]
72
Control
Logic
CQ
36
Reg.
36
Reg.
36
Reg.
CQ
36
DQ[35: 0]
36
Document #: 38-05563 Rev. *D
Page 3 of 28
[+] Feedback
CY7C1516V18
CY7C1527V18
CY7C1518V18
CY7C1520V18
Pin Configurations [1]
165-ball FBGA (15 x 17 x 1.4 mm) Pinout
CY7C1516V18 (8M x 8)
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
1
2
3
4
5
6
7
8
9
CQ
NC
NC
NC
NC
10
11
A
A
NWS1
NC
K
K
A
CQ
NC
NC
DQ3
NC
NC
NC
NC
VSS
VSS
A
VSS
VSS
NC
VSS
A
VSS
NWS0
A
VSS
LD
A
A
NC
R/W
A
NC
NC
NC
NC
NC
NC
NC
NC
DQ4
VDDQ
VSS
VSS
VSS
VDDQ
NC
NC
DQ2
NC
NC
NC
VDDQ
VDD
VSS
VDD
VDDQ
DOFF
NC
NC
VREF
NC
DQ5
VDDQ
NC
VDDQ
VDDQ
VDDQ
VDD
VDD
VDD
VSS
VSS
VSS
VDD
VDD
VDD
VDDQ
VDDQ
VDDQ
NC
NC
VDDQ
NC
NC
VREF
DQ1
NC
NC
ZQ
NC
NC
NC
NC
VDDQ
VDD
VSS
VDD
VDDQ
NC
NC
NC
NC
DQ6
NC
VDDQ
VSS
VSS
VSS
VDDQ
NC
NC
DQ0
NC
NC
NC
NC
NC
NC
VSS
VSS
VSS
A
VSS
A
VSS
A
VSS
VSS
NC
NC
NC
NC
NC
NC
NC
NC
DQ7
A
A
C
A
A
NC
NC
NC
TDO
TCK
A
A
A
C
A
A
A
TMS
TDI
10
11
NC
NC
CY7C1527V18 (8M x 9)
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
1
2
3
4
5
6
7
8
9
CQ
NC
A
A
K
K
NC
LD
A
A
A
CQ
NC
R/W
A
NC
NC
NC
NC
DQ3
NC
NC
NC
NC
NC
A
NC
VSS
VSS
NC
NC
NC
NC
DQ4
VDDQ
NC
BWS0
A
VSS
VSS
VSS
NC
VSS
A
VSS
NC
NC
NC
VSS
VSS
VSS
VDDQ
NC
NC
DQ2
NC
NC
NC
VDDQ
VDD
VSS
VDD
VDDQ
NC
NC
NC
NC
NC
VREF
NC
DQ5
VDDQ
NC
VDDQ
VDDQ
VDDQ
VDD
VDD
VDD
VSS
VSS
VSS
VDD
VDD
VDD
VDDQ
VDDQ
VDDQ
NC
VDDQ
NC
NC
VREF
DQ1
NC
ZQ
NC
DOFF
NC
NC
NC
NC
VDDQ
VDD
VSS
VDD
VDDQ
NC
NC
NC
NC
DQ6
NC
VDDQ
VSS
VSS
VSS
VDDQ
NC
NC
DQ0
NC
NC
NC
NC
NC
NC
VSS
VSS
VSS
A
VSS
A
VSS
A
VSS
VSS
NC
NC
NC
NC
NC
NC
NC
NC
DQ7
A
A
C
A
A
NC
NC
DQ8
TDO
TCK
A
A
A
C
A
A
A
TMS
TDI
Note:
1. VSS/144M and VSS/288M are not connected to the die and can be tied to any voltage level.
Document #: 38-05563 Rev. *D
Page 4 of 28
[+] Feedback
CY7C1516V18
CY7C1527V18
CY7C1518V18
CY7C1520V18
Pin Configurations [1] (continued)
165-ball FBGA (15 x 17 x 1.4 mm) Pinout
CY7C1518V18 (4M x 18)
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
1
2
3
4
5
6
7
8
9
CQ
NC
NC
NC
A
A
BWS1
NC
K
K
A
CQ
NC
NC
DQ8
NC
NC
NC
DQ10
VSS
VSS
A
VSS
VSS
NC
VSS
A0
VSS
BWS0
A
VSS
LD
A
A
NC
R/W
A
NC
DQ9
NC
DQ7
NC
NC
NC
NC
NC
DQ11
VDDQ
VSS
VSS
VSS
VDDQ
NC
NC
DQ6
NC
DQ12
NC
VDDQ
VDD
VSS
VDD
VDDQ
NC
NC
DQ5
NC
NC
VREF
NC
DQ13
VDDQ
NC
VDDQ
VDDQ
VDDQ
VDD
VDD
VDD
VSS
VSS
VSS
VDD
VDD
VDD
VDDQ
VDDQ
VDDQ
NC
VDDQ
NC
NC
VREF
DQ4
NC
ZQ
NC
NC
NC
DQ14
VDDQ
VDD
VSS
VDD
VDDQ
NC
NC
DQ3
NC
DQ15
NC
VDDQ
VSS
VSS
VSS
VDDQ
NC
NC
DQ2
NC
NC
NC
NC
NC
DQ16
VSS
VSS
VSS
A
VSS
A
VSS
A
VSS
VSS
NC
NC
DQ1
NC
NC
NC
NC
NC
DQ17
A
A
C
A
A
NC
NC
DQ0
TDO
TCK
A
A
A
C
A
A
A
TMS
TDI
DOFF
NC
10
11
CY7C1520V18 (2M x 36)
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
1
2
3
4
5
6
7
8
9
10
11
CQ
NC
VSS/144M
A
BWS2
LD
A
A
A
CQ
DQ18
K
K
BWS1
DQ27
R/W
A
NC
NC
NC
DQ29
DQ28
DQ19
VSS
VSS
NC
NC
DQ20
VDDQ
NC
NC
DQ30
DQ21
DQ31
VREF
NC
DOFF
NC
NC
DQ8
VSS
VSS
NC
VSS
BWS0
A
VSS
NC
A0
VSS
NC
DQ17
NC
DQ7
DQ16
VSS
VSS
VSS
VDDQ
NC
DQ15
DQ6
VDDQ
VDD
VSS
VDDQ
VDDQ
VDDQ
VDDQ
VDD
VDD
VDD
VSS
VSS
VSS
VDDQ
VDDQ
VDDQ
NC
NC
VDDQ
NC
NC
DQ22
VDDQ
DQ32
VDD
VDD
VDD
VDD
NC
VREF
DQ13
DQ5
DQ14
ZQ
DQ4
BWS3
A
NC
NC
DQ23
VDDQ
VDD
VSS
VDD
VDDQ
NC
DQ12
DQ3
NC
DQ33
DQ24
VDDQ
VSS
VSS
VSS
VDDQ
NC
NC
DQ2
NC
NC
NC
DQ35
DQ34
DQ25
VSS
VSS
VSS
A
VSS
A
VSS
A
VSS
VSS
NC
NC
DQ11
NC
DQ1
DQ10
NC
NC
DQ26
A
A
C
A
A
NC
DQ9
DQ0
TDO
TCK
A
A
A
C
A
A
A
TMS
TDI
Document #: 38-05563 Rev. *D
Page 5 of 28
[+] Feedback
CY7C1516V18
CY7C1527V18
CY7C1518V18
CY7C1520V18
Pin Definitions
Pin Name
I/O
Pin Description
DQ[x:0]
Input/Output- Data Input/Output signals. Inputs are sampled on the rising edge of K and K clocks during valid
Synchronous Write operations. These pins drive out the requested data during a Read operation. Valid data is
driven out on the rising edge of both the C and C clocks during Read operations or K and K when
in single clock mode. When read access is deselected, Q[x:0] are automatically tri-stated.
CY7C1516V18 − DQ[7:0]
CY7C1527V18 − DQ[8:0]
CY7C1518V18 − DQ[17:0]
CY7C1520V18 − DQ[35:0]
LD
InputSynchronous Load. This input is brought LOW when a bus cycle sequence is to be defined.
Synchronous This definition includes address and Read/Write direction. All transactions operate on a burst of
2 data.
NWS0, NWS1
InputNibble Write Select 0, 1 − active LOW (CY7C1516V18 only).Sampled on the rising edge of the
Synchronous K and K clocks during Write operations. Used to select which nibble is written into the device
during the current portion of the Write operations. Nibbles not written remain unaltered.
NWS0 controls D[3:0] and NWS1 controls D[7:4].
All the Nibble Write Selects are sampled on the same edge as the data. Deselecting a Nibble
Write Select will cause the corresponding nibble of data to be ignored and not written into the
device.
BWS0, BWS1,
InputByte Write Select 0, 1, 2, and 3 − active LOW. Sampled on the rising edge of the K and K clocks
BWS2, BWS3 Synchronous during Write operations. Used to select which byte is written into the device during the current
portion of the Write operations. Bytes not written remain unaltered.
CY7C1527V18 − BWS0 controls D[8:0]
CY7C1518V18 − BWS0 controls D[8:0] and BWS1 controls D[17:9].
CY7C1520V18 − BWS0 controls D[8:0], BWS1 controls D[17:9], BWS2 controls D[26:18] and BWS3
controls D[35:27].
All the Byte Write Selects are sampled on the same edge as the data. Deselecting a Byte Write
Select will cause the corresponding byte of data to be ignored and not written into the device.
A, A0
InputAddress Inputs. These address inputs are multiplexed for both Read and Write operations.
Synchronous Internally, the device is organized as 8M x 8 (2 arrays each of 4M x 8) for CY7C1516V18 and
8M x 9 (2 arrays each of 4M x9) for CY7C1527V18, a single 4M x 18 array for CY7C1518V18,
and a single array of 2M x 36 for CY7C1520V18.
CY7C1516V18 – Since the least significant bit of the address internally is a “0,” only 22 external
address inputs are needed to access the entire memory array.
CY7C1527V18 – Since the least significant bit of the address internally is a “0,” only 22 external
address inputs are needed to access the entire memory array.
CY7C1518V18 – A0 is the input to the burst counter. These are incremented in a linear fashion
internally. 22 address inputs are needed to access the entire memory array.
CY7C1520V18 – A0 is the input to the burst counter. These are incremented in a linear fashion
internally. 21 address inputs are needed to access the entire memory array. All the address inputs
are ignored when the appropriate port is deselected.
R/W
InputSynchronous Read/Write Input. When LD is LOW, this input designates the access type (Read
Synchronous when R/W is HIGH, Write when R/W is LOW) for loaded address. R/W must meet the set-up and
hold times around edge of K.
C
InputClock
Positive Input Clock for Output Data. C is used in conjunction with C to clock out the Read data
from the device. C and C can be used together to deskew the flight times of various devices on
the board back to the controller. See application example for further details.
C
InputClock
Negative Input Clock for Output Data. C is used in conjunction with C to clock out the Read
data from the device. C and C can be used together to deskew the flight times of various devices
on the board back to the controller. See application example for further details.
K
InputClock
Positive Input Clock Input. The rising edge of K is used to capture synchronous inputs to the
device and to drive out data through Q[x:0] when in single clock mode. All accesses are initiated
on the rising edge of K.
K
InputClock
Negative Input Clock Input. K is used to capture synchronous data being presented to the device
and to drive out data through Q[x:0] when in single clock mode.
Document #: 38-05563 Rev. *D
Page 6 of 28
[+] Feedback
CY7C1516V18
CY7C1527V18
CY7C1518V18
CY7C1520V18
Pin Definitions (continued)
Pin Name
I/O
Pin Description
CQ
OutputClock
CQ is referenced with respect to C. This is a free running clock and is synchronized to the Input
clock for output data (C) of the DDR-II. In the single clock mode, CQ is generated with respect to
K. The timings for the echo clocks are shown in the AC Timing table.
CQ
OutputClock
ZQ
Input
CQ is referenced with respect to C. This is a free running clock and is synchronized to the Input
clock for output data (C) of the DDR-II. In the single clock mode, CQ is generated with respect to
K. The timings for the echo clocks are shown in the AC Timing table.
Output Impedance Matching Input. This input is used to tune the device outputs to the system
data bus impedance. CQ, CQ, and Q[x:0] output impedance are set to 0.2 x RQ, where RQ is a
resistor connected between ZQ and ground. Alternately, this pin can be connected directly to
VDDQ, which enables the minimum impedance mode. This pin cannot be connected directly to
GND or left unconnected.
DOFF
Input
DLL Turn Off - active LOW. Connecting this pin to ground will turn off the DLL inside the device.
The timings in the DLL turned off operation will be different from those listed in this data sheet.
TDO
Output
TDO for JTAG.
TCK
Input
TCK pin for JTAG.
TDI
Input
TDI pin for JTAG.
TMS
Input
TMS pin for JTAG.
NC
N/A
Not connected to the die. Can be tied to any voltage level.
VSS/144M
Input
Address expansion for 144M. Can be tied to any voltage level.
VSS/288M
Input
Address expansion for 288M. Can be tied to any voltage level.
VREF
VDD
VSS
VDDQ
InputReference
Reference Voltage Input. Static input used to set the reference level for HSTL inputs and Outputs
as well as AC measurement points.
Power Supply Power supply inputs to the core of the device.
Ground
Ground for the device.
Power Supply Power supply inputs for the outputs of the device.
Document #: 38-05563 Rev. *D
Page 7 of 28
[+] Feedback
CY7C1516V18
CY7C1527V18
CY7C1518V18
CY7C1520V18
Functional Overview
The CY7C1516V18, CY7C1527V18, CY7C1518V18, and
CY7C1520V18 are synchronous pipelined Burst SRAMs
equipped with a DDR interface.
memory array at the specified location. Write accesses can be
initiated on every rising edge of the positive input clock (K).
Doing so will pipeline the data flow such that 18 bits of data
can be transferred into the device on every rising edge of the
input clocks (K and K).
Accesses are initiated on the rising edge of the positive input
clock (K). All synchronous input timing is referenced from the
rising edge of the input clocks (K and K) and all output timing
is referenced to the rising edge of the output clocks (C/C or
K/K when in single clock mode).
When write access is deselected, the device will ignore all
inputs after the pending Write operations have been
completed.
All synchronous data inputs (D[x:0]) pass through input
registers controlled by the rising edge of the input clocks (K
and K). All synchronous data outputs (Q[x:0]) pass through
output registers controlled by the rising edge of the output
clocks (C/C or K/K when in single-clock mode).
Byte Write operations are supported by the CY7C1518V18. A
Write operation is initiated as described in the Write Operation
section above. The bytes that are written are determined by
BWS0 and BWS1 which are sampled with each set of 18-bit
data word. Asserting the appropriate Byte Write Select input
during the data portion of a Write will allow the data being
presented to be latched and written into the device.
Deasserting the Byte Write Select input during the data portion
of a write will allow the data stored in the device for that byte
to remain unaltered. This feature can be used to simplify
Read/Modify/Write operations to a Byte Write operation.
All synchronous control (R/W, LD, BWS[0:X]) inputs pass
through input registers controlled by the rising edge of the
input clock (K).
CY7C1518V18 is described in the following sections. The
same basic descriptions apply to CY7C1516V18,
CY7C1527V18, and CY7C1520V18.
Read Operations
The CY7C1518V18 is organized internally as a single array of
4M x 18. Accesses are completed in a burst of two sequential
18-bit data words. Read operations are initiated by asserting
R/W HIGH and LD LOW at the rising edge of the positive input
clock (K). The address presented to Address inputs is stored
in the Read address register and the least significant bit of the
address is presented to the burst counter. The burst counter
increments the address in a linear fashion. Following the next
K clock rise the corresponding 18-bit word of data from this
address location is driven onto the Q[17:0] using C as the output
timing reference. On the subsequent rising edge of C the next
18-bit data word from the address location generated by the
burst counter is driven onto the Q[17:0]. The requested data will
be valid 0.45 ns from the rising edge of the output clock (C or
C, or K and K when in single clock mode, 200-MHz, 250-MHz
and 300-MHz device). In order to maintain the internal logic,
each read access must be allowed to complete. Read
accesses can be initiated on every rising edge of the positive
input clock (K).
When read access is deselected, the CY7C1518V18 will first
complete the pending read transactions. Synchronous internal
circuitry will automatically tri-state the outputs following the
next rising edge of the positive output clock (C). This will allow
for a seamless transition between devices without the
insertion of wait states in a depth expanded memory.
Write Operations
Write operations are initiated by asserting R/W LOW and LD
LOW at the rising edge of the positive input clock (K). The
address presented to Address inputs is stored in the Write
address register and the least significant bit of the address is
presented to the burst counter. The burst counter increments
the address in a linear fashion. On the following K clock rise
the data presented to D[17:0] is latched and stored into the
18-bit Write Data register provided BWS[1:0] are both asserted
active. On the subsequent rising edge of the Negative Input
Clock (K) the information presented to D[17:0] is also stored
into the Write Data register provided BWS[1:0] are both
asserted active. The 36 bits of data are then written into the
Document #: 38-05563 Rev. *D
Byte Write Operations
Single Clock Mode
The CY7C1518V18 can be used with a single clock that
controls both the input and output registers. In this mode the
device will recognize only a single pair of input clocks (K and
K) that control both the input and output registers. This
operation is identical to the operation if the device had zero
skew between the K/K and C/C clocks. All timing parameters
remain the same in this mode. To use this mode of operation,
the user must tie C and C HIGH at power-on. This function is
a strap option and not alterable during device operation.
DDR Operation
The CY7C1518V18 enables high-performance operation
through high clock frequencies (achieved through pipelining)
and double data rate mode of operation. The CY7C1518V18
requires a single No Operation (NOP) cycle when transitioning
from a Read to a Write cycle. At higher frequencies, some
applications may require a second NOP cycle to avoid
contention.
If a Read occurs after a Write cycle, address and data for the
Write are stored in registers. The write information must be
stored because the SRAM cannot perform the last word Write
to the array without conflicting with the Read. The data stays
in this register until the next Write cycle occurs. On the first
Write cycle after the Read(s), the stored data from the earlier
Write will be written into the SRAM array. This is called a
Posted Write.
If a Read is performed on the same address on which a Write
is performed in the previous cycle, the SRAM reads out the
most current data. The SRAM does this by bypassing the
memory array and reading the data from the registers.
Depth Expansion
Depth expansion requires replicating the LD control signal for
each bank. All other control signals can be common between
banks as appropriate.
Page 8 of 28
[+] Feedback
CY7C1516V18
CY7C1527V18
CY7C1518V18
CY7C1520V18
Programmable Impedance
respect to K and CQ is generated with respect to K. The
timings for the echo clocks are shown in the AC Timing table.
An external resistor, RQ, must be connected between the ZQ
pin on the SRAM and VSS to allow the SRAM to adjust its
output driver impedance. The value of RQ must be 5x the
value of the intended line impedance driven by the SRAM, The
allowable range of RQ to guarantee impedance matching with
a tolerance of ±15% is between 175Ω and 350Ω, with
VDDQ = 1.5V. The output impedance is adjusted every 1024
cycles upon power-up to account for drifts in supply voltage
and temperature.
DLL
These chips utilize a Delay Lock Loop (DLL) that is designed
to function between 80 MHz and the specified maximum clock
frequency. During power-up, when the DOFF is tied HIGH, the
DLL gets locked after 1024 cycles of stable clock. The DLL can
also be reset by slowing or stopping the input clock K and K
for a minimum of 30 ns. However, it is not necessary for the
DLL to be specifically reset in order to lock the DLL to the
desired frequency. The DLL will automatically lock 1024 clock
cycles after a stable clock is presented.the DLL may be
disabled by applying ground to the DOFF pin. For information
refer to the application note “DLL Considerations in
QDRII™/DDRII/QDRII+/DDRII+”.
Echo Clocks
Echo clocks are provided on the DDR-II to simplify data
capture on high-speed systems. Two echo clocks are
generated by the DDR-II. CQ is referenced with respect to C
and CQ is referenced with respect to C. These are
free-running clocks and are synchronized to the output clock
of the DDR-II. In the single clock mode, CQ is generated with
Application Example[2]
DQ
A
DQ
Addresses
Cycle Start#
R/W#
Return CLK
Source CLK
Return CLK#
Source CLK#
Echo Clock1/Echo Clock#1
Echo Clock2/Echo Clock#2
BUS
MASTER
(CPU
or
ASIC)
ZQ
CQ/CQ#
LD# R/W# C C# K K#
SRAM#1
DQ
A
R = 250ohms
ZQ
CQ/CQ#
LD# R/W# C C# K K#
SRAM#2
R = 250ohms
Vterm = 0.75V
R = 50ohms
Vterm = 0.75V
Truth Table[3, 4, 5, 6, 7, 8]
K
LD
R/W
Write Cycle:
Load address; wait one cycle; input write data on
consecutive K and K rising edges.
Operation
L-H
L
L
D(A1) at K(t + 1) ↑
D(A2) at K(t + 1) ↑
Read Cycle:
Load address; wait one and a half cycle; read data on
consecutive C and C rising edges.
L-H
L
H
Q(A1) at C(t + 1) ↑
Q(A2) at C(t + 2) ↑
L-H
H
X
High-Z
High-Z
Stopped
X
X
Previous State
Previous State
NOP: No Operation
Standby: Clock Stopped
DQ
DQ
Burst Address Table (CY7C1518V18, CY7C1520V18)
First Address (External)
Second Address (Internal)
X..X0
X..X1
X..X1
X..X0
Notes:
2. The above application shows two DDR-II used.
3. X = “Don’t Care,” H = Logic HIGH, L = Logic LOW, ↑represents rising edge.
4. Device will power-up deselected and the outputs in a tri-state condition.
5. On CY7C1518V18 and CY7C1520V18, “A1” represents address location latched by the devices when transaction was initiated and A2 represents the addresses
sequence in the burst. On CY7C1516V18, “A1” represents A +‘0’ and A2 represents A +‘1.’
6. “t” represents the cycle at which a Read/Write operation is started. t+1 and t + 2 are the first and second clock cycles succeeding the “t” clock cycle.
7. Data inputs are registered at K and K rising edges. Data outputs are delivered on C and C rising edges, except when in single clock mode.
8. It is recommended that K = K and C = C = HIGH when clock is stopped. This is not essential, but permits most rapid restart by overcoming transmission line
charging symmetrically.
Document #: 38-05563 Rev. *D
Page 9 of 28
[+] Feedback
CY7C1516V18
CY7C1527V18
CY7C1518V18
CY7C1520V18
Write Cycle Descriptions (CY7C1516V18 and CY7C1518V18)[3, 9]
BWS0, NWS0
BWS1, NWS1
K
K
L
L
L-H
–
During the Data portion of a Write sequence :
CY7C1516V18 − both nibbles (D[7:0]) are written into the device,
CY7C1518V18 − both bytes (D[17:0]) are written into the device.
L
L
–
L-H
During the Data portion of a Write sequence :
CY7C1516V18 − both nibbles (D[7:0]) are written into the device,
CY7C1518V18 − both bytes (D[17:0]) are written into the device.
L
H
L-H
–
During the Data portion of a Write sequence :
CY7C1516V18 − only the lower nibble (D[3:0]) is written into the device. D[7:4]
will remain unaltered,
CY7C1518V18 − only the lower byte (D[8:0]) is written into the device. D[17:9]
will remain unaltered.
L
H
–
L-H
During the Data portion of a Write sequence :
CY7C1516V18 − only the lower nibble (D[3:0]) is written into the device. D[7:4]
will remain unaltered,
CY7C1518V18 − only the lower byte (D[8:0]) is written into the device. D[17:9]
will remain unaltered.
H
L
L-H
–
During the Data portion of a Write sequence :
CY7C1516V18 − only the upper nibble (D[7:4]) is written into the device. D[3:0]
will remain unaltered,
CY7C1518V18 − only the upper byte (D[17:9]) is written into the device. D[8:0]
will remain unaltered.
H
L
–
L-H
During the Data portion of a Write sequence :
CY7C1516V18 − only the upper nibble (D[7:4]) is written into the device. D[3:0]
will remain unaltered,
CY7C1518V18 − only the upper byte (D[17:9]) is written into the device. D[8:0]
will remain unaltered.
H
H
L-H
–
No data is written into the devices during this portion of a Write operation.
H
H
–
L-H
No data is written into the devices during this portion of a Write operation.
Document #: 38-05563 Rev. *D
Comments
Page 10 of 28
[+] Feedback
CY7C1516V18
CY7C1527V18
CY7C1518V18
CY7C1520V18
Write Cycle Descriptions[3, 9] (CY7C1520V18)
BWS0
BWS1
BWS2
BWS3
K
K
L
L
L
L
L-H
–
During the Data portion of a Write sequence, all four bytes (D[35:0]) are
written into the device.
L
L
L
L
–
L-H
During the Data portion of a Write sequence, all four bytes (D[35:0]) are
written into the device.
L
H
H
H
L-H
–
During the Data portion of a Write sequence, only the lower byte (D[8:0]) is
written into the device. D[35:9] will remain unaltered.
L
H
H
H
–
L-H
During the Data portion of a Write sequence, only the lower byte (D[8:0]) is
written into the device. D[35:9] will remain unaltered.
H
L
H
H
L-H
–
During the Data portion of a Write sequence, only the byte (D[17:9]) is
written into the device. D[8:0] and D[35:18] will remain unaltered.
H
L
H
H
–
L-H
During the Data portion of a Write sequence, only the byte (D[17:9]) is
written into the device. D[8:0] and D[35:18] will remain unaltered.
H
H
L
H
L-H
–
During the Data portion of a Write sequence, only the byte (D[26:18]) is
written into the device. D[17:0] and D[35:27] will remain unaltered.
H
H
L
H
–
L-H
During the Data portion of a Write sequence, only the byte (D[26:18]) is
written into the device. D[17:0] and D[35:27] will remain unaltered.
H
H
H
L
L-H
H
H
H
L
–
L-H
H
H
H
H
L-H
–
No data is written into the device during this portion of a Write operation.
H
H
H
H
–
L-H
No data is written into the device during this portion of a Write operation.
Comments
During the Data portion of a Write sequence, only the byte (D[35:27]) is
written into the device. D[26:0] will remain unaltered.
During the Data portion of a Write sequence, only the byte (D[35:27]) is
written into the device. D[26:0] will remain unaltered.
Write Cycle Descriptions[3, 9](CY7C1527V18)
BWS0
K
K
Comments
L
L-H
–
During the Data portion of a Write sequence, the single byte (D[8:0]) is
written into the device.
L
–
L-H
During the Data portion of a Write sequence, the single byte (D[8:0]) is
written into the device.
H
L-H
–
No data is written into the device during this portion of a Write operation.
H
–
L-H
No data is written into the device during this portion of a Write operation.
Note:
9. Assumes a Write cycle was initiated per the Write Port Cycle Description Truth Table. NWS0, NWS1,BWS0, BWS1,BWS2 and BWS3 can be altered on different
portions of a write cycle, as long as the set-up and hold requirements are achieved.
Document #: 38-05563 Rev. *D
Page 11 of 28
[+] Feedback
CY7C1516V18
CY7C1527V18
CY7C1518V18
CY7C1520V18
IEEE 1149.1 Serial Boundary Scan (JTAG)
These SRAMs incorporate a serial boundary scan test access
port (TAP) in the FBGA package. This part is fully compliant
with IEEE Standard #1149.1-1900. The TAP operates using
JEDEC standard 1.8V I/O logic levels.
Disabling the JTAG Feature
It is possible to operate the SRAM without using the JTAG
feature. To disable the TAP controller, TCK must be tied LOW
(VSS) to prevent clocking of the device. TDI and TMS are internally pulled up and may be unconnected. They may alternately
be connected to VDD through a pull-up resistor. TDO should
be left unconnected. Upon power-up, the device will come up
in a reset state which will not interfere with the operation of the
device.
TDI and TDO pins as shown in TAP Controller Block Diagram.
Upon power-up, the instruction register is loaded with the
IDCODE instruction. It is also loaded with the IDCODE
instruction if the controller is placed in a reset state as
described in the previous section.
When the TAP controller is in the Capture IR state, the two
least significant bits are loaded with a binary “01” pattern to
allow for fault isolation of the board level serial test path.
Bypass Register
To save time when serially shifting data through registers, it is
sometimes advantageous to skip certain chips. The bypass
register is a single-bit register that can be placed between TDI
and TDO pins. This allows data to be shifted through the
SRAM with minimal delay. The bypass register is set LOW
(VSS) when the BYPASS instruction is executed.
Test Access Port—Test Clock
Boundary Scan Register
The test clock is used only with the TAP controller. All inputs
are captured on the rising edge of TCK. All outputs are driven
from the falling edge of TCK.
The boundary scan register is connected to all of the input and
output pins on the SRAM. Several no connect (NC) pins are
also included in the scan register to reserve pins for higher
density devices.
Test Mode Select
The TMS input is used to give commands to the TAP controller
and is sampled on the rising edge of TCK. It is allowable to
leave this pin unconnected if the TAP is not used. The pin is
pulled up internally, resulting in a logic HIGH level.
Test Data-In (TDI)
The TDI pin is used to serially input information into the
registers and can be connected to the input of any of the
registers. The register between TDI and TDO is chosen by the
instruction that is loaded into the TAP instruction register. For
information on loading the instruction register, see the TAP
Controller State Diagram. TDI is internally pulled up and can
be unconnected if the TAP is unused in an application. TDI is
connected to the most significant bit (MSB) on any register.
Test Data-Out (TDO)
The TDO output pin is used to serially clock data-out from the
registers. The output is active depending upon the current
state of the TAP state machine (see Instruction codes). The
output changes on the falling edge of TCK. TDO is connected
to the least significant bit (LSB) of any register.
Performing a TAP Reset
A Reset is performed by forcing TMS HIGH (VDD) for five rising
edges of TCK. This RESET does not affect the operation of
the SRAM and may be performed while the SRAM is
operating. At power-up, the TAP is reset internally to ensure
that TDO comes up in a high-Z state.
TAP Registers
Registers are connected between the TDI and TDO pins and
allow data to be scanned into and out of the SRAM test
circuitry. Only one register can be selected at a time through
the instruction registers. Data is serially loaded into the TDI pin
on the rising edge of TCK. Data is output on the TDO pin on
the falling edge of TCK.
Instruction Register
Three-bit instructions can be serially loaded into the instruction
register. This register is loaded when it is placed between the
Document #: 38-05563 Rev. *D
The boundary scan register is loaded with the contents of the
RAM Input and Output ring when the TAP controller is in the
Capture-DR state and is then placed between the TDI and
TDO pins when the controller is moved to the Shift-DR state.
The EXTEST, SAMPLE/PRELOAD and SAMPLE Z instructions can be used to capture the contents of the Input and
Output ring.
The Boundary Scan Order tables show the order in which the
bits are connected. Each bit corresponds to one of the bumps
on the SRAM package. The MSB of the register is connected
to TDI, and the LSB is connected to TDO.
Identification (ID) Register
The ID register is loaded with a vendor-specific, 32-bit code
during the Capture-DR state when the IDCODE command is
loaded in the instruction register. The IDCODE is hardwired
into the SRAM and can be shifted out when the TAP controller
is in the Shift-DR state. The ID register has a vendor code and
other information described in the Identification Register
Definitions table.
TAP Instruction Set
Eight different instructions are possible with the three-bit
instruction register. All combinations are listed in the
Instruction Code table. Three of these instructions are listed
as RESERVED and should not be used. The other five instructions are described in detail below.
Instructions are loaded into the TAP controller during the
Shift-IR state when the instruction register is placed between
TDI and TDO. During this state, instructions are shifted
through the instruction register through the TDI and TDO pins.
To execute the instruction once it is shifted in, the TAP
controller needs to be moved into the Update-IR state.
IDCODE
The IDCODE instruction causes a vendor-specific, 32-bit code
to be loaded into the instruction register. It also places the
instruction register between the TDI and TDO pins and allows
the IDCODE to be shifted out of the device when the TAP
controller enters the Shift-DR state. The IDCODE instruction
Page 12 of 28
[+] Feedback
CY7C1516V18
CY7C1527V18
CY7C1518V18
CY7C1520V18
is loaded into the instruction register upon power-up or
whenever the TAP controller is given a test logic reset state.
SAMPLE Z
The SAMPLE Z instruction causes the boundary scan register
to be connected between the TDI and TDO pins when the TAP
controller is in a Shift-DR state. The SAMPLE Z command puts
the output bus into a High-Z state until the next command is
given during the “Update IR” state.
SAMPLE/PRELOAD
SAMPLE/PRELOAD is a 1149.1 mandatory instruction. When
the SAMPLE/PRELOAD instructions are loaded into the instruction register and the TAP controller is in the Capture-DR
state, a snapshot of data on the inputs and output pins is captured in the boundary scan register.
The user must be aware that the TAP controller clock can only
operate at a frequency up to 20 MHz, while the SRAM clock
operates more than an order of magnitude faster. Because
there is a large difference in the clock frequencies, it is possible that during the Capture-DR state, an input or output will
undergo a transition. The TAP may then try to capture a signal
while in transition (metastable state). This will not harm the
device, but there is no guarantee as to the value that will be
captured. Repeatable results may not be possible.
To guarantee that the boundary scan register will capture the
correct value of a signal, the SRAM signal must be stabilized
long enough to meet the TAP controller's capture set-up plus
hold times (tCS and tCH). The SRAM clock input might not be
captured correctly if there is no way in a design to stop (or
slow) the clock during a SAMPLE/PRELOAD instruction. If this
is an issue, it is still possible to capture all other signals and
simply ignore the value of the CK and CK captured in the
boundary scan register.
Once the data is captured, it is possible to shift out the data by
putting the TAP into the Shift-DR state. This places the boundary scan register between the TDI and TDO pins.
PRELOAD allows an initial data pattern to be placed at the
latched parallel outputs of the boundary scan register cells prior to the selection of another boundary scan test operation.
BYPASS
When the BYPASS instruction is loaded in the instruction
register and the TAP is placed in a Shift-DR state, the bypass
register is placed between the TDI and TDO pins. The
advantage of the BYPASS instruction is that it shortens the
boundary scan path when multiple devices are connected
together on a board.
EXTEST
The EXTEST instruction enables the preloaded data to be
driven out through the system output pins. This instruction also
selects the boundary scan register to be connected for serial
access between the TDI and TDO in the shift-DR controller
state.
EXTEST Output Bus Tri-State
IEEE Standard 1149.1 mandates that the TAP controller be
able to put the output bus into a tri-state mode.
The boundary scan register has a special bit located at bit
#108. When this scan cell, called the “extest output bus
tri-state”, is latched into the preload register during the
“Update-DR” state in the TAP controller, it will directly control
the state of the output (Q-bus) pins, when the EXTEST is
entered as the current instruction. When HIGH, it will enable
the output buffers to drive the output bus. When LOW, this bit
will place the output bus into a High-Z condition.
This bit can be set by entering the SAMPLE/PRELOAD or
EXTEST command, and then shifting the desired bit into that
cell, during the “Shift-DR” state. During “Update-DR”, the value
loaded into that shift-register cell will latch into the preload
register. When the EXTEST instruction is entered, this bit will
directly control the output Q-bus pins. Note that this bit is
pre-set HIGH to enable the output when the device is
powered-up, and also when the TAP controller is in the
“Test-Logic-Reset” state.
Reserved
These instructions are not implemented but are reserved for
future use. Do not use these instructions.
The shifting of data for the SAMPLE and PRELOAD phases
can occur concurrently when required—that is, while data
captured is shifted out, the preloaded data can be shifted in.
Document #: 38-05563 Rev. *D
Page 13 of 28
[+] Feedback
CY7C1516V18
CY7C1527V18
CY7C1518V18
CY7C1520V18
TAP Controller State Diagram[10]
1
TEST-LOGIC
RESET
0
0
TEST-LOGIC/
IDLE
1
1
1
SELECT
DR-SCAN
SELECT
IR-SCAN
0
0
1
1
CAPTURE-DR
CAPTURE-IR
0
0
0
SHIFT-DR
0
SHIFT-IR
1
1
1
EXIT1-DR
1
EXIT1-IR
0
0
PAUSE-DR
0
0
PAUSE-IR
1
1
0
0
EXIT2-DR
EXIT2-IR
1
1
UPDATE-DR
1
0
UPDATE-IR
1
0
Note:
10. The 0/1 next to each state represents the value at TMS at the rising edge of TCK.
Document #: 38-05563 Rev. *D
Page 14 of 28
[+] Feedback
CY7C1516V18
CY7C1527V18
CY7C1518V18
CY7C1520V18
TAP Controller Block Diagram
0
Bypass Register
Selection
Circuitry
2
TDI
1
0
1
0
Selection
Circuitry
TDO
Instruction Register
31 30 29
.
.
2
Identification Register
106 .
.
.
.
2
1
0
Boundary Scan Register
TCK
TAP Controller
TMS
TAP Electrical Characteristics Over the Operating Range[16, 18, 11]
Parameter
Description
Test Conditions
Min.
Max.
Unit
VOH1
Output HIGH Voltage
IOH = −2.0 mA
1.4
V
VOH2
Output HIGH Voltage
IOH = −100 µA
1.6
V
VOL1
Output LOW Voltage
IOL = 2.0 mA
0.4
V
VOL2
Output LOW Voltage
IOL = 100 µA
0.2
V
VIH
Input HIGH Voltage
0.65 VDD
VDD + 0.3
V
VIL
Input LOW Voltage
–0.3
0.35 VDD
V
IX
Input and OutputLoad Current
−5
5
µA
GND ≤ VI ≤ VDD
TAP AC Switching Characteristics Over the Operating Range[12, 13]
Parameter
Description
Min.
Max.
Unit
tTCYC
TCK Clock Cycle Time
tTF
TCK Clock Frequency
tTH
TCK Clock HIGH
20
ns
tTL
TCK Clock LOW
20
ns
50
ns
20
MHz
Notes:
11. These characteristics pertain to the TAP inputs (TMS, TCK, TDI and TDO). Parallel load levels are specified in the Electrical Characteristics Table.
12. tCS and tCH refer to the set-up and hold time requirements of latching data from the boundary scan register.
13. Test conditions are specified using the load in TAP AC test conditions. tR/tF = 1 ns.
Document #: 38-05563 Rev. *D
Page 15 of 28
[+] Feedback
CY7C1516V18
CY7C1527V18
CY7C1518V18
CY7C1520V18
TAP AC Switching Characteristics Over the Operating Range[12, 13] (continued)
Parameter
Description
Min.
Max.
Unit
Set-up Times
tTMSS
TMS Set-up to TCK Clock Rise
5
ns
tTDIS
TDI set-up to TCK Clock Rise
5
ns
tCS
Capture Set-up to TCK Rise
5
ns
Hold Times
tTMSH
TMS Hold after TCK Clock Rise
5
ns
tTDIH
TDI Hold after Clock Rise
5
ns
tCH
Capture Hold after Clock Rise
5
ns
Output Times
tTDOV
TCK Clock LOW to TDO Valid
tTDOX
TCK Clock LOW to TDO Invalid
10
0
ns
ns
TAP Timing and Test Conditions[13]
0.9V
50Ω
ALL INPUT PULSES
TDO
1.8V
Z0 = 50Ω
0.9V
CL = 20 pF
0V
tTH
(a)
tTL
GND
Test Clock
TCK
tTCYC
tTMSS
tTMSH
Test Mode Select
TMS
tTDIS
tTDIH
Test Data-In
TDI
Test Data-Out
TDO
tTDOV
Document #: 38-05563 Rev. *D
tTDOX
Page 16 of 28
[+] Feedback
CY7C1516V18
CY7C1527V18
CY7C1518V18
CY7C1520V18
Identification Register Definitions
Value
Instruction
Field
CY7C1516V18
CY7C1527V18
CY7C1518V18
CY7C1520V18
Description
Revision
Number (31:29)
000
000
000
000
Version number.
Cypress Device
ID (28:12)
11010100010000100
Cypress JEDEC
ID (11:1)
00000110100
00000110100
00000110100
00000110100
Allows unique
identification of
SRAM vendor.
1
1
1
1
Indicate the
presence of an
ID register.
ID Register
Presence (0)
11010100010001100 11010100010010100 11010100010100100 Defines the type
of SRAM.
Scan Register Sizes
Register Name
Bit Size
Instruction
3
Bypass
1
ID
32
Boundary Scan
109
Instruction Codes
Instruction
Code
Description
EXTEST
000
Captures the Input/Output ring contents.
IDCODE
001
Loads the ID register with the vendor ID code and places the register between TDI and TDO.
This operation does not affect SRAM operation.
SAMPLE Z
010
Captures the Input/Output contents. Places the boundary scan register between TDI and TDO.
Forces all SRAM output drivers to a High-Z state.
RESERVED
011
Do Not Use: This instruction is reserved for future use.
SAMPLE/PRELOAD
100
Captures the Input/Output ring contents. Places the boundary scan register between TDI and
TDO. Does not affect the SRAM operation.
RESERVED
101
Do Not Use: This instruction is reserved for future use.
RESERVED
110
Do Not Use: This instruction is reserved for future use.
BYPASS
111
Places the bypass register between TDI and TDO. This operation does not affect SRAM operation.
Document #: 38-05563 Rev. *D
Page 17 of 28
[+] Feedback
CY7C1516V18
CY7C1527V18
CY7C1518V18
CY7C1520V18
Boundary Scan Order
Bit #
Bump ID
Bit #
Bump ID
Bit #
Bump ID
Bit #
Bump ID
0
6R
28
10G
56
6A
84
1J
1
6P
29
9G
57
5B
85
2J
2
6N
30
11F
58
5A
86
3K
3
7P
31
11G
59
4A
87
3J
4
7N
32
9F
60
5C
88
2K
5
7R
33
10F
61
4B
89
1K
6
8R
34
11E
62
3A
90
2L
7
8P
35
10E
63
2A
91
3L
8
9R
36
10D
64
1A
92
1M
9
11P
37
9E
65
2B
93
1L
10
10P
38
10C
66
3B
94
3N
11
10N
39
11D
67
1C
95
3M
12
9P
40
9C
68
1B
96
1N
13
10M
41
9D
69
3D
97
2M
14
11N
42
11B
70
3C
98
3P
15
9M
43
11C
71
1D
99
2N
16
9N
44
9B
72
2C
100
2P
17
11L
45
10B
73
3E
101
1P
18
11M
46
11A
74
2D
102
3R
19
9L
47
10A
75
2E
103
4R
20
10L
48
9A
76
1E
104
4P
21
11K
49
8B
77
2F
105
5P
22
10K
50
7C
78
3F
106
5N
23
9J
51
6C
79
1G
107
5R
24
9K
52
8A
80
1F
108
Internal
25
10J
53
7A
81
3G
26
11J
54
7B
82
2G
27
11H
55
6B
83
1H
Document #: 38-05563 Rev. *D
Page 18 of 28
[+] Feedback
CY7C1516V18
CY7C1527V18
CY7C1518V18
CY7C1520V18
Power-Up Sequence in DDR-II SRAM[14, 15]
DDR-II SRAMs must be powered up and initialized in a
predefined manner to prevent undefined operations.
Power-Up Sequence
• Apply power and drive DOFF LOW (All other inputs can be
HIGH or LOW)
— Apply VDD before VDDQ
— Apply VDDQ before VREF or at the same time as VREF
DLL Constraints
• DLL uses either K or C clock as its synchronizing input.The
input should have low phase jitter, which is specified as
tKC Var.
• The DLL will function at frequencies down to 80 MHz.
• If the input clock is unstable and the DLL is enabled, then
the DLL may lock to an incorrect frequency, causing
unstable SRAM behavior.
• After the power and clock (K, K, C, C) are stable take DOFF
HIGH
• The additional 1024 cycles of clocks are required for the
DLL to lock.
~
~
Power-up Waveforms
K
K
~
~
Unstable Clock
> 1024 Stable clock
Start Normal
Operation
Clock Start (Clock Starts after V DD / V DDQ Stable)
VDD / VDDQ
DOFF
V DD / V DDQ Stable (< +/- 0.1V DC per 50ns )
Fix High (or tied to VDDQ)
Notes:
14. It is recommended that the DOFF pin be pulled HIGH via a pull up resistor of 1 Kohm.
15. During Power-Up, when the DOFF is tied HIGH, the DLL gets locked after 1024 cycles of stable clock.
Document #: 38-05563 Rev. *D
Page 19 of 28
[+] Feedback
CY7C1516V18
CY7C1527V18
CY7C1518V18
CY7C1520V18
Maximum Ratings
Current into Outputs (LOW)......................................... 20 mA
Static Discharge Voltage (MIL-STD-883, M 3015).... >2001V
(Above which the useful life may be impaired.)
Storage Temperature ................................. –65°C to +150°C
Ambient Temperature with Power Applied .. –55°C to +125°C
Latch-up Current..................................................... >200 mA
Operating Range
Supply Voltage on VDD Relative to GND........ –0.5V to +2.9V
Supply Voltage on VDDQ Relative to GND ...... –0.5V to +VDD
DC Applied to Outputs in High-Z......... –0.5V to VDDQ + 0.3V
DC Input Voltage[16] ...............................–0.5V to VDD + 0.3V
Range
Com’l
Ind’l
Ambient
Temperature
VDD[17]
VDDQ[17]
0°C to +70°C
1.8 ± 0.1V
1.4V to VDD
–40°C to +85°C
Electrical Characteristics Over the Operating Range[18]
DC Electrical Characteristics Over the Operating Range
Parameter
Description
Test Conditions
Min.
Typ.
Max.
Unit
VDD
Power Supply Voltage
1.7
1.8
1.9
V
VDDQ
I/O Supply Voltage
1.4
1.5
VDD
V
VOH
Output HIGH Voltage
Note 19
VDDQ/2 – 0.12
VDDQ/2 + 0.12
V
VOL
Output LOW Voltage
Note 19
VDDQ/2 – 0.12
VDDQ/2 + 0.12
V
VDDQ – 0.2
VDDQ
V
VSS
0.2
V
VOH(LOW)
Output HIGH Voltage
IOH = –0.1 mA, Nominal Impedance
VOL(LOW)
Output LOW Voltage
IOL = 0.1 mA, Nominal Impedance
VIH
Input HIGH Voltage[16]
VREF + 0.1
VDDQ + 0.3
V
VIL
Input LOW Voltage[16]
–0.3
VREF – 0.1
V
IX
Input Leakage Current
GND ≤ VI ≤ VDDQ
–5
5
µA
IOZ
Output Leakage Current
GND ≤ VI ≤ VDDQ, Output Disabled
–5
5
µA
Voltage[21]
VREF
Input Reference
IDD
VDD Operating Supply
ISB1
Automatic Power-down
Current
Typical Value = 0.75V
0.95
V
VDD = Max., IOUT = 0 mA, 167 MHz
f = fMAX = 1/tCYC
200 MHz
650
mA
700
mA
250 MHz
800
mA
278 MHz
860
mA
300 MHz
900
mA
167 MHz
340
mA
200 MHz
360
mA
250 MHz
380
mA
278 MHz
390
mA
300 MHz
400
mA
Max. VDD, Both Ports
Deselected, VIN ≥ VIH or
VIN ≤ VIL
f = fMAX = 1/tCYC,
Inputs Static
0.68
0.75
AC Input Requirements Over the Operating Range
Min.
Typ.
Max.
Unit
VIH
Parameter
Input HIGH Voltage
Description
Test Conditions
VREF + 0.2
–
–
V
VIL
Input LOW Voltage
–
–
VREF – 0.2
V
Notes:
16. Overshoot: VIH(AC) < VDD + 0.85V (Pulse width less than tTCYC/2); Undershoot VIL(AC) > -1.5V (Pulse width less than tTCYC/2).
17. Power-up: Assumes a linear ramp from 0V to VDD(Min.,) within 200ms. During this time VIH < VDD and VDDQ < VDD.
18. All voltages referenced to ground.
19. Outputs are impedance controlled. IOH = -(VDDQ/2)/(RQ/5) for values of 175Ω < RQ < 350Ω.
20. Outputs are impedance controlled. IOL = (VDDQ/2)/(RQ/5) for values of 175Ω < RQ < 350Ω.
21. VREF (Min.) = 0.68V or 0.46VDDQ, whichever is larger, VREF (Max.) = 0.95V or 0.54VDDQ, whichever is smaller.
Document #: 38-05563 Rev. *D
Page 20 of 28
[+] Feedback
CY7C1516V18
CY7C1527V18
CY7C1518V18
CY7C1520V18
Capacitance[22]
Parameter
Description
Test Conditions
Input Capacitance
TA = 25°C, f = 1 MHz,
Clock Input Capacitance VDD = 1.8V
VDDQ = 1.5V
Output Capacitance
CIN
CCLK
CO
Max.
5.5
8.5
8
Unit
pF
pF
pF
Thermal Resistance[22]
Parameter
Description
ΘJA
Thermal Resistance
(Junction to Ambient)
ΘJC
Thermal Resistance
(Junction to Case)
Test Conditions
FBGA
Unit
Test conditions follow standard test methods and
procedures for measuring thermal impedance,
per EIA/JESD51.
16.2
°C/W
2.3
°C/W
AC Test Loads and Waveforms
VREF = 0.75V
VREF
0.75V
VREF
OUTPUT
Z0 = 50Ω
Device
Under
Test
RL = 50Ω
VREF = 0.75V
ZQ
RQ =
250Ω
0.75V
R = 50Ω
ALL INPUT PULSES
1.25V
0.75V
OUTPUT
Device
Under
Test ZQ
5 pF
[23]
0.25V
Slew Rate = 2 V/ns
RQ =
250Ω
(a)
(b)
Notes:
22. Tested initially and after any design or process change that may affect these parameters.
23. Unless otherwise noted, test conditions assume signal transition time of 2V/ns, timing reference levels of 0.75V, VREF = 0.75V, RQ = 250Ω, VDDQ = 1.5V, input
pulse levels of 0.25V to 1.25V, and output loading of the specified IOL/IOH and load capacitance shown in (a) of AC Test Loads.
Document #: 38-05563 Rev. *D
Page 21 of 28
[+] Feedback
CY7C1516V18
CY7C1527V18
CY7C1518V18
CY7C1520V18
Switching Characteristics Over the Operating Range [23, 24]
300 MHz
Cypress Consortium
Parameter Parameter
Description
VDD(Typical) to the first
Access[25]
tPOWER
278 MHz
250 MHz
200 MHz
167 MHz
Min. Max. Min. Max. Min. Max. Min. Max. Min. Max.
1
–
1
–
Unit
1
–
1
–
1
–
ms
tCYC
tKHKH
K Clock and C Clock Cycle
Time
3.30 5.25 3.60 5.25
4.0
6.3
5.0
7.9
6.0
8.4
ns
tKH
tKHKL
Input Clock (K/K and C/C)
HIGH
1.32
–
1.4
–
1.6
–
2.0
–
2.4
–
ns
tKL
tKLKH
Input Clock (K/K and C/C)
LOW
1.32
–
1.4
–
1.6
–
2.0
–
2.4
–
ns
tKHKH
tKHKH
K Clock Rise to K Clock Rise 1.49
and C to C Rise (rising edge
to rising edge)
–
1.6
–
1.8
–
2.2
–
2.7
–
ns
tKHCH
tKHCH
K/K Clock Rise to C/C Clock Rise 0.00 1.45
(rising edge to rising edge)
0.0
1.55
0.0
1.8
0.0
2.2
0.0
2.7
ns
Set-up Times
tSA
tAVKH
Address Set-up to K Clock
Rise
0.4
–
0.4
–
0.5
–
0.6
–
0.7
–
ns
tSC
tIVKH
Control Set-up to K Clock
Rise (LD, R/W)
0.4
–
0.4
–
0.5
–
0.6
–
0.7
–
ns
tSCDDR
tIVKH
Double Data Rate Control
Set-up to Clock (K/K) Rise
(BWS0, BWS1, BWS2,
BWS3)
0.3
–
0.3
–
0.35
–
0.4
–
0.5
–
ns
tSD[26]
tDVKH
D[X:0] Set-up to Clock
(K/K) Rise
0.3
–
0.3
–
0.35
–
0.4
–
0.5
–
ns
Hold Times
tHA
tKHAX
Address Hold after K Clock
Rise
0.4
–
0.4
–
0.5
–
0.6
–
0.7
–
ns
tHC
tKHIX
Control Hold after K Clock
Rise (LD, R/W)
0.4
–
0.4
–
0.5
–
0.6
–
0.7
–
ns
tHCDDR
tKHIX
Double Data Rate Control
Hold after Clock (K/K) Rise
(BWS0, BWS1, BWS2,
BWS3)
0.3
–
0.3
–
0.35
–
0.4
–
0.5
–
ns
tHD
tKHDX
D[X:0] Hold after Clock
(K/K) Rise
0.3
–
0.3
–
0.35
–
0.4
–
0.5
–
ns
–
0.45
–
0.45
–
0.45
–
0.45
–
0.50
ns
Output Times
tCO
tCHQV
C/C Clock Rise (or K/K in single
clock mode) to Data Valid
tDOH
tCHQX
Data Output Hold after
Output C/C Clock Rise
(Active to Active)
–0.45
–
–0.45
–
–0.45
–
–0.45
–
–0.50
–
ns
tCCQO
tCHCQV
C/C Clock Rise to Echo
Clock Valid
–
0.45
–
0.45
–
0.45
–
0.45
–
0.50
ns
Notes:
24. All devices can operate at clock frequencies as low as 119 MHz. When a part with a maximum frequency above 133 MHz is operating at a lower clock frequency,
it requires the input timings of the frequency range in which it is being operated and will output data with the output timings of that frequency range.
25. This part has a voltage regulator internally; tPOWER is the time that the power needs to be supplied above VDD minimum initially before a read or write operation
can be initiated.
26. For DQ0 data signal on CY7C1527V18 device, tSD is 0.5ns for 200MHz, 250MHz, 278MHz and 300MHz frequencies.
Document #: 38-05563 Rev. *D
Page 22 of 28
[+] Feedback
CY7C1516V18
CY7C1527V18
CY7C1518V18
CY7C1520V18
Switching Characteristics Over the Operating Range (continued)[23, 24]
300 MHz
Cypress Consortium
Parameter Parameter
Description
278 MHz
250 MHz
200 MHz
167 MHz
Min. Max. Min. Max. Min. Max. Min. Max. Min. Max.
Unit
–0.45
–
–0.45
–
–0.45
–
–0.45
–
–0.50
–
ns
Echo Clock High to Data
Valid
–
0.27
–
0.27
–
0.30
–
0.35
–
0.40
ns
tCQHQX
Echo Clock High to Data
Invalid
–0.27
–
–0.27
–
–0.30
–
–0.35
–
–0.40
–
ns
tCHZ
tCHQZ
Clock (C and C) Rise to High-Z
(Active to High-Z)[27, 28]
–
0.45
–
0.45
–
0.45
–
0.45
–
0.50
ns
tCLZ
tCHQX1
Clock (C and C) Rise to
Low-Z[27, 28]
–0.45
–
–0.45
–
–0.45
–
–0.45
–
–0.50
–
ns
tCQOH
tCHCQX
Echo Clock Hold after C/C
Clock Rise
tCQD
tCQHQV
tCQDOH
DLL Timing
tKC Var
tKC Var
Clock Phase Jitter
–
0.20
–
0.20
–
0.20
–
0.20
–
0.20
ns
tKC lock
tKC lock
DLL Lock Time (K, C)
1024
–
1024
–
1024
–
1024
–
1024
–
Cycles
tKC Reset
tKC Reset
K Static to DLL Reset
30
–
30
–
30
–
30
–
30
–
ns
Notes:
27. tCHZ, tCLZ, are specified with a load capacitance of 5 pF as in part (b) of AC Test Loads. Transition is measured ± 100 mV from steady-state voltage.
28. At any given voltage and temperature tCHZ is less than tCLZ and tCHZ less than tCO.
Document #: 38-05563 Rev. *D
Page 23 of 28
[+] Feedback
CY7C1516V18
CY7C1527V18
CY7C1518V18
CY7C1520V18
Switching Waveforms[29, 30, 31]
READ
2
NOP
1
READ
3
NOP
4
NOP
5
WRITE
6
WRITE
7
READ
8
A3
A4
9
10
K
tKH
tKL
tKHKH
tCYC
K
LD
tSC tHC
R/W
A
A0
tSA
A2
A1
tHD
tHA
tHD
tSD
DQ
Q00
t KHCH
t CLZ
Q01
Q10
Q11
tSD
D20
D21
D30
D31
Q40
Q41
t CQDOH
t CHZ
tDOH
tCO
t CQD
C
t KHCH
tKH
tKL
tCYC
tKHKH
C#
tCQOH
tCCQO
CQ
tCQOH
tCCQO
CQ#
DON’T CARE
UNDEFINED
Notes:
29. Q00 refers to output from address A0. Q01 refers to output from the next internal burst address following A0, i.e., A0+1.
30. Output are disabled (High-Z) one clock cycle after a NOP.
31. In this example, if address A2 = A1,then data Q20 = D10 and Q21 = D11. Write data is forwarded immediately as read results. This note applies to the whole diagram.
Document #: 38-05563 Rev. *D
Page 24 of 28
[+] Feedback
CY7C1516V18
CY7C1527V18
CY7C1518V18
CY7C1520V18
Ordering Information
Not all of the speed, package and temperature ranges are available. Please contact your local sales representative or
visit www.cypress.com for actual products offered
Speed
(MHz)
167
Ordering Code
CY7C1516V18-167BZC
Package
Diagram
Operating
Range
Package Type
51-85195 165-ball Fine Pitch Ball Grid Array (15 x 17 x 1.4 mm)
Commercial
CY7C1527V18-167BZC
CY7C1518V18-167BZC
CY7C1520V18-167BZC
CY7C1516V18-167BZXC
51-85195 165-ball Fine Pitch Ball Grid Array (15 x 17 x 1.4 mm) Lead-Free
CY7C1527V18-167BZXC
CY7C1518V18-167BZXC
CY7C1520V18-167BZXC
CY7C1516V18-167BZI
51-85195 165-ball Fine Pitch Ball Grid Array (15 x 17 x 1.4 mm)
Industrial
CY7C1527V18-167BZI
CY7C1518V18-167BZI
CY7C1520V18-167BZI
CY7C1516V18-167BZXI
51-85195 165-ball Fine Pitch Ball Grid Array (15 x 17 x 1.4 mm) Lead-Free
CY7C1527V18-167BZXI
CY7C1518V18-167BZXI
CY7C1520V18-167BZXI
200
CY7C1516V18-200BZC
51-85195 165-ball Fine Pitch Ball Grid Array (15 x 17 x 1.4 mm)
Commercial
CY7C1527V18-200BZC
CY7C1518V18-200BZC
CY7C1520V18-200BZC
CY7C1516V18-200BZXC
51-85195 165-ball Fine Pitch Ball Grid Array (15 x 17 x 1.4 mm) Lead-Free
CY7C1527V18-200BZXC
CY7C1518V18-200BZXC
CY7C1520V18-200BZXC
CY7C1516V18-200BZI
51-85195 165-ball Fine Pitch Ball Grid Array (15 x 17 x 1.4 mm)
Industrial
CY7C1527V18-200BZI
CY7C1518V18-200BZI
CY7C1520V18-200BZI
CY7C1516V18-200BZXI
51-85195 165-ball Fine Pitch Ball Grid Array (15 x 17 x 1.4 mm) Lead-Free
CY7C1527V18-200BZXI
CY7C1518V18-200BZXI
CY7C1520V18-200BZXI
250
CY7C1516V18-250BZC
51-85195 165-ball Fine Pitch Ball Grid Array (15 x 17 x 1.4 mm)
Commercial
CY7C1527V18-250BZC
CY7C1518V18-250BZC
CY7C1520V18-250BZC
CY7C1516V18-250BZXC
51-85195 165-ball Fine Pitch Ball Grid Array (15 x 17 x 1.4 mm) Lead-Free
CY7C1527V18-250BZXC
CY7C1518V18-250BZXC
CY7C1520V18-250BZXC
Document #: 38-05563 Rev. *D
Page 25 of 28
[+] Feedback
CY7C1516V18
CY7C1527V18
CY7C1518V18
CY7C1520V18
Ordering Information (continued)
Not all of the speed, package and temperature ranges are available. Please contact your local sales representative or
visit www.cypress.com for actual products offered
Speed
(MHz)
250
Ordering Code
CY7C1516V18-250BZI
Package
Diagram
Operating
Range
Package Type
51-85195 165-ball Fine Pitch Ball Grid Array (15 x 17 x 1.4 mm)
Industrial
CY7C1527V18-250BZI
CY7C1518V18-250BZI
CY7C1520V18-250BZI
CY7C1516V18-250BZXI
51-85195 165-ball Fine Pitch Ball Grid Array (15 x 17 x 1.4 mm) Lead-Free
CY7C1527V18-250BZXI
CY7C1518V18-250BZXI
CY7C1520V18-250BZXI
278
CY7C1516V18-278BZC
51-85195 165-ball Fine Pitch Ball Grid Array (15 x 17 x 1.4 mm)
Commercial
CY7C1527V18-278BZC
CY7C1518V18-278BZC
CY7C1520V18-278BZC
CY7C1516V18-278BZXC
51-85195 165-ball Fine Pitch Ball Grid Array (15 x 17 x 1.4 mm) Lead-Free
CY7C1527V18-278BZXC
CY7C1518V18-278BZXC
CY7C1520V18-278BZXC
CY7C1516V18-278BZI
51-85195 165-ball Fine Pitch Ball Grid Array (15 x 17 x 1.4 mm)
Industrial
CY7C1527V18-278BZI
CY7C1518V18-278BZI
CY7C1520V18-278BZI
CY7C1516V18-278BZXI
51-85195 165-ball Fine Pitch Ball Grid Array (15 x 17 x 1.4 mm) Lead-Free
CY7C1527V18-278BZXI
CY7C1518V18-278BZXI
CY7C1520V18-278BZXI
300
CY7C1516V18-300BZC
51-85195 165-ball Fine Pitch Ball Grid Array (15 x 17 x 1.4 mm)
Commercial
CY7C1527V18-300BZC
CY7C1518V18-300BZC
CY7C1520V18-300BZC
CY7C1516V18-300BZXC
51-85195 165-ball Fine Pitch Ball Grid Array (15 x 17 x 1.4 mm) Lead-Free
CY7C1527V18-300BZXC
CY7C1518V18-300BZXC
CY7C1520V18-300BZXC
CY7C1516V18-300BZI
51-85195 165-ball Fine Pitch Ball Grid Array (15 x 17 x 1.4 mm)
Industrial
CY7C1527V18-300BZI
CY7C1518V18-300BZI
CY7C1520V18-300BZI
CY7C1516V18-300BZXI
51-85195 165-ball Fine Pitch Ball Grid Array (15 x 17 x 1.4 mm) Lead-Free
CY7C1527V18-300BZXI
CY7C1518V18-300BZXI
CY7C1520V18-300BZXI
Document #: 38-05563 Rev. *D
Page 26 of 28
[+] Feedback
CY7C1516V18
CY7C1527V18
CY7C1518V18
CY7C1520V18
Package Diagram
165-ball FBGA (15 x 17 x 1.40 mm) (51-85195)
"/44/- 6)%7
4/0 6)%7
Π- # ! "
Œ
0). #/2.%2
Π- #
0). #/2.%2
8
!
"
"
#
#
!
$
$
&
&
'
'
(
*
%
¼
%
(
*
+
,
,
+
-
-
.
.
0
0
2
2
!
"
¼
./4%3 #
¼
¼
#
8
3/,$%2 0!$ 490% ./. 3/,$%2 -!3+ $%&).%$ .3-$
0!#+!'% 7%)'(4 G
*%$%# 2%&%2%.#% -/ $%3)'. #
0!#+!'% #/$% ""!$
-!8
3%!4).' 0,!.%
#
51-85195-*A
DDR RAMs and Quad Data Rate RAMs comprise a new family of products developed by Cypress, Hitachi, IDT, Micron, NEC and
Samsung technology. All product and company names mentioned in this document are the trademarks of their respective holders.
Document #: 38-05563 Rev. *D
Page 27 of 28
© Cypress Semiconductor Corporation, 2006. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use
of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be
used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its
products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress
products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
[+] Feedback
CY7C1516V18
CY7C1527V18
CY7C1518V18
CY7C1520V18
Document History Page
Document Title: CY7C1516V18/CY7C1527V18/CY7C1518V18/CY7C1520V18 72-Mbit DDR-II SRAM 2-Word
Burst Architecture
Document Number: 38-05563
REV.
ECN No.
Issue Date
Orig. of
Change
Description of Change
**
226981
See ECN
DIM
New Data Sheet
*A
257089
See ECN
NJY
Modified ID code for the x9 option in the JTAG ID Register Definitions table on
page 21
Included thermal values
Modified capacitance values table: included capacitance values for x8, x18 and
x36 options
*B
319496
See ECN
SYT
Removed CY7C1527V18 from the title
Included 300-MHz Speed Bin
Added footnote #1 and accordingly edited the VSS/144M And VSS/288M on the
Pin Definitions table
Added Industrial Temperature Grade
Replaced TBDs for IDD and ISB1 for 300 MHz, 250 MHz, 200 MHz and 167 MHz
speed grades
Changed the CIN from 5 pF to 5.5 pF and CO from 7 pF to 8 pF in the
Capacitance Table
Removed the capacitance value column for the x9 option from Capacitance Table
Changed typo of bit # 47 to bit # 108 under the EXTEST OUTPUT BUS
TRI-STATE on Page 17
Added lead-free product information
Updated the Ordering Information by Shading and unshading as per availability
*C
403231
See ECN
ZSD
Converted from Preliminary to Final
Added CY7C1527V18 part number to the title
Included 278-MHz Speed Bin
Changed C/C Pin Description in the features section and Pin Description
Changed the address of Cypress Semiconductor Corporation on Page#1 from
“3901 North First Street” to “198 Champion Court”
Added power-up sequence details and waveforms
Added foot notes #14, 15, 16 on page# 19
Replaced Three-state with Tri-state
Changed the description of IX from Input Load Current to Input Leakage Current
on page# 20
Modified the IDD and ISB1 values for different speed bins
Replaced Package Name column with Package Diagram in the Ordering
Information table
Updated the Ordering Information table
*D
467290
See ECN
NXR
Modified the ZQ Definition from Alternately this pin can be connected directly to
VDD to Alternately, this pin can be connected directly to VDDQ
Included Maximum Ratings for Supply Voltage on VDDQ Relative to GND
Changed the Maximum Ratings for DC Input Voltage from VDDQ to VDD
Changed tTCYC from 100 ns to 50 ns, changed tTH and tTL from 40 ns to 20 ns,
changed tTMSS, tTDIS, tCS, tTMSH, tTDIH, tCH from 10 ns to 5 ns and changed tTDOV
from 20 ns to 10 ns in TAP AC Switching Characteristics table
Modified Power-Up waveform
Changed the Maximum rating of Ambient Temperature with Power Applied from
–10°C to +85°C to –55°C to +125°C
Added additional notes in the AC parameter section
Modified AC Switching Waveform
Corrected the typo In the AC Switching Characteristics Table
Updated the Ordering Information Table
Document #: 38-05563 Rev. *D
Page 28 of 28
[+] Feedback