Micrel MAX823WEXK Voltage supervisor with watchdog timer and manual reset Datasheet

MAX823/4/5
Voltage Supervisor with Watchdog Timer
and Manual Reset
Revision 1.0
General Description
The MAX823/4/5 voltage supervisory circuits combine
low-current, manual reset input, watchdog timer, activehigh and active-low push-pull outputs. The reset outputs
are asserted and held when the supply voltage falls below
the factory-programmed threshold voltage, when the /MR
pin is pulled low, or if the watchdog times out. Reset is
asserted for the reset timeout delay after the supply
voltage increases above the rising threshold voltage or
when manual reset input is asserted high.
The MAX823/4/5 features an integrated pull-up resistor on
the /MR pin. An active-low push-pull reset output (/RESET)
and an active-high reset output (RESET) provide flexibility
when interfacing with various microcontrollers, PMICs, or
load switches. The watchdog input can be left
unconnected for applications that do not require watchdog
monitoring.
The MAX823/4/5 consumes a quiescent current of only
3.8µA and is offered in standard SOT23-5 and SC70-5
packages. It is rated for the –40°C to +125°C temperature
range.
Datasheets and support documentation are available on
Micrel’s web site at: www.micrel.com.
Features













Precision 1.665V to 4.625V power supply monitor
±0.5% threshold accuracy at TA = +25°C
±1.5% threshold accuracy from TA = –40°C to +125°C
3.8µA supply current (S,R,T,W,Y,Z options)
4.8µA supply current (L,M options)
Manual reset input (MAX823/5)
140ms (min.) reset timeout period
1.6s (typ.) watchdog timeout period
Active-high and active-low push-pull outputs
Guaranteed reset output valid to VCC = 1V
40°C to +125°C junction temperature range
5-pin SOT23 & SC70 packages
8x lower watchdog input current than competition
Applications






Computers and Controllers
Embedded Controllers
Intelligent Instruments
Automotive Systems
Critical µP Monitoring
Portable/ Battery-Powered Equipment
Typical Application
Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com
January 14, 2014
Revision 1.0
Micrel, Inc.
MAX823/4/5
FUNCTION
MAX823
MAX824
MAX825
Active-Low Reset



Active-High Reset
−


Watchdog Input


−
Manual Reset Input

−

Ordering Information(1)
Part Number
Top Marking
VRST: Nominal Threshold
Voltage (V)
Package
MAX823LEUK
X3L
4.625
SOT23-5
MAX823MEUK
X3M
4.375
SOT23-5
MAX823REUK
X3R
2.625
SOT23-5
MAX823SEUK
X3S
2.925
SOT23-5
MAX823TEUK
X3T
3.075
SOT23-5
MAX823WEUK
X3W
1.665
SOT23-5
MAX823YEUK
X3Y
2.188
SOT23-5
MAX823ZEUK
X3Z
2.315
SOT23-5
MAX823LEXK
XA
4.625
SC70-5
MAX823MEXK
XB
4.375
SC70-5
MAX823REXK
XF
2.625
SC70-5
MAX823SEXK
XE
2.925
SC70-5
MAX823TEXK
XC
3.075
SC70-5
MAX823WEXK
XL
1.665
SC70-5
MAX823YEXK
XK
2.188
SC70-5
MAX823ZEXK
XJ
2.315
SC70-5
January 14, 2014
2
Revision 1.0
Micrel, Inc.
MAX823/4/5
Ordering Information (Continued)(1)
Part Number
Top Marking
VRST: Nominal Threshold
Voltage (V)
Package
MAX824LEUK
X4L
4.625
SOT23-5
MAX824MEUK
X4M
4.375
SOT23-5
MAX824REUK
X4R
2.625
SOT23-5
MAX824SEUK
X4S
2.925
SOT23-5
MAX824TEUK
X4T
3.075
SOT23-5
MAX824WEUK
X4W
1.665
SOT23-5
MAX824YEUK
X4Y
2.188
SOT23-5
MAX824ZEUK
X4Z
2.315
SOT23-5
MAX824LEXK
4Y
4.625
SC70-5
MAX824MEXK
YA
4.375
SC70-5
MAX824REXK
YD
2.625
SC70-5
MAX824SEXK
YC
2.925
SC70-5
MAX824TEXK
YB
3.075
SC70-5
MAX824WEXK
YG
1.665
SC70-5
MAX824YEXK
YF
2.188
SC70-5
MAX824ZEXK
YE
2.315
SC70-5
Part Number
Top Marking
VRST: Nominal Threshold
Voltage (V)
Package
MAX825LEUK
X5L
4.625
SOT23-5
MAX825MEUK
X5M
4.375
SOT23-5
MAX825REUK
X5R
2.625
SOT23-5
MAX825SEUK
X5S
2.925
SOT23-5
MAX825TEUK
X5T
3.075
SOT23-5
MAX825WEUK
X5W
1.665
SOT23-5
MAX825YEUK
X5Y
2.188
SOT23-5
MAX825ZEUK
X5Z
2.315
SOT23-5
MAX825LEXK
YE
4.625
SC70-5
MAX825MEXK
YI
4.375
SC70-5
MAX825REXK
YO
2.625
SC70-5
MAX825SEXK
YK
2.925
SC70-5
MAX825TEXK
YJ
3.075
SC70-5
MAX825WEXK
YT
1.665
SC70-5
MAX825YEXK
YS
2.188
SC70-5
MAX825ZEXK
YR
2.315
SC70-5
Note:
1. All devices are available in tape-and-reel only. Contact Micrel for tape-and-reel options.
January 14, 2014
3
Revision 1.0
Micrel, Inc.
MAX823/4/5
Pin Configuration
MAX823
MAX824
MAX825
SOT23(EUK) &SC70(EXK)
SOT23(EUK) &SC70(EXK)
SOT23(EUK) &SC70(EXK)
Top View
Top View
Top View
Pin Description
Pin Number
MAX823
Pin Number
MAX824
Pin Number
MAX825
Pin Name
1
1
1
/RESET
2
2
2
GND
-
4
3
5
January 14, 2014
3
4
-
5
3
-
4
5
Pin Function
Active-Low Reset Output. Pulses low for 200ms when triggered, and
remains low whenever VCC is below the reset threshold or when /MR is
a logic low. It remains low for 200ms after one of the following occurs:
VCC rises above the reset threshold, the watchdog triggers a reset, or
/MR goes low to high.
Ground.
RESET
Active-High Reset Output. Pulses high for 200ms when triggered, and
remains high whenever VCC is below the reset threshold or when /MR
is a logic low. It remains high for 200ms after one of the following
occurs: VCC rises above the reset threshold, the watchdog triggers a
reset, or /MR goes low to high. RESET is the inverse of /RESET.
WDI
Watchdog Input. If WDI remains either high or low for longer than the
watchdog timeout period, the internal watchdog timer runs out and a
reset is triggered. The internal watchdog timer clears whenever reset
is asserted, or whenever WDI sees a rising or falling edge. If WDI is
left unconnected or is connected to a three-stated buffer output, the
watchdog feature is disabled.
/MR
Manual Reset Input. A logic low on /MR asserts reset. Reset remains
asserted as long as /MR is held low and for 200ms after /MR returns
high. The active-low input has an internal 52kΩ pull-up resistor. It can
be driven from a CMOS logic line or shorted to ground with a switch.
Leave open or connect to VCC if unused.
VCC
Supply Voltage Pin. VCC is the input to the supply voltage monitor.
When the supply voltage falls below the reset threshold voltage, reset
outputs (/RESET and RESET) are triggered immediately. When the
supply voltage rises above the reset threshold plus hysteresis voltage,
the reset outputs remain asserted for the duration of the reset timeout
period. An optional 0.1µF bypass capacitor mounted close to VCC
provides additional transient immunity.
4
Revision 1.0
Micrel, Inc.
MAX823/4/5
Absolute Maximum Ratings(2)
Operating Ratings(3)
Supply Voltage (VCC) .................................... 0.3V to 6.0V
/MR, WDI, RESET, /RESET.................. 0.3V to VCC +0.3V
Input Current (All Pins except RESET, /RESET) ........ 20mA
Output Current (RESET, /RESET) .............................. 20mA
Junction Temperature (TJ) ........................ 40°C to +150°C
Storage Temperature (Ts)......................... 65°C to +150°C
(4)
ESD Rating (Human Body Model)(MAX823/4/5) ........ 3kV
Supply Voltage (VCC) .................................... +1.0V to +5.5V
Watchdog Input (WDI)........................................... 0V to VCC
Junction Temperature (TJ) ........................ –40°C to +125°C
Junction Thermal Resistance
5-Pin SOT23 .................................................... 215°C/W
5-Pin SC70 ...................................................... 250°C/W
Electrical Characteristics(5)
VCC = 4.7V to 5.5V for MAX823/4/5L, VCC = 4.5V to 5.5V for MAX823/4/5M, VCC = 3.15V to 3.6V for MAX823/4/5T, VCC = 3.0V to 3.6V
for MAX823/4/5S, VCC = 2.7V to 3.6V for MAX823/4/5R, VCC = 2.38V to 2.75V for MAX823/4/5Z, VCC = 2.25V to 2.75V for
(6)
MAX823/4/5Y, VCC = 1.75V to 2.0V for MAX823/4/5W; TJ = +25˚C, bold values indicate –40˚C ≤ TJ ≤ +125˚C, unless otherwise noted.
Parameter
Condition
Min.
Typ.
Max.
Units
5.5
V
Power Suppy Input
1.0
Supply Voltage (VCC)
Supply Current (IVCC)
L/M (WDI and /MR unconnected)
4.8
14
µA
T/S/R/Z/Y/W (WDI and /MR unconnected)
3.8
8.4
µA
4.625
4.648
V
4.694
V
4.397
V
4.441
V
3.090
V
3.121
V
2.940
V
2.969
V
2.638
V
2.664
V
2.327
V
2.350
V
2.199
V
2.221
V
1.673
V
1.690
V
Reset Threshold Voltage
Reset Threshold Voltage
(VRST)
Reset Threshold
Hysteresis
L (falling) TA = 25C
4.602
L (falling) 40C  TA  +125C
4.556
M (falling) TA = 25C
4.353
M (falling) –40C  TA  +125C
4.309
T (falling) TA = 25C
3.060
T (falling) –40C  TA  +125C
3.029
S (falling) TA = 25C
2.910
S (falling) –40C  TA  +125C
2.881
R (falling) TA = 25C
2.612
R (falling) –40C  TA  +125C
2.586
Z (falling) TA = 25C
2.303
Z (falling) –40C  TA  +125C
2.280
Y (falling) TA = 25C
2.177
Y (falling) –40C  TA  +125C
2.155
W (falling) TA = 25C
1.657
W (falling) –40C  TA  +125C
1.640
3.075
2.925
2.625
2.315
2.188
1.665
L, M
10
mV
T, S, R, Z, Y, W
5
mV
40
ppm/˚C
Reset Threshold Tempco
January 14, 2014
4.375
5
Revision 1.0
Micrel, Inc.
MAX823/4/5
Electrical Characteristics (Continued)(5)
VCC = 4.7V to 5.5V for MAX823/4/5L, VCC = 4.5V to 5.5V for MAX823/4/5M, VCC = 3.15V to 3.6V for MAX823/4/5T, VCC = 3.0V to 3.6V
for MAX823/4/5S, VCC = 2.7V to 3.6V for MAX823/4/5R, VCC = 2.38V to 2.75V for MAX823/4/5Z, VCC = 2.25V to 2.75V for
(6)
MAX823/4/5Y, VCC = 1.75V to 2.0V for MAX823/4/5W; TJ = +25˚C, bold values indicate –40˚C ≤ TJ ≤ +125˚C, unless otherwise noted.
Parameter
Condition
Reset Timeout Period
(tRP)
Min.
Typ.
Max.
Units
140
200
280
ms
Reset Time
VCC to /RESET Delay
(tRD)
10
µs
Reset Outputs (/RESET, RESET)
/RESET Output Voltage
High (VOH)
/RESET Output Voltage
Low (VOL)
/RESET Output Short(7)
Circuit Current
RESET Output Voltage
High (VOH)
VCC – 1.5
V
T, S, R, Z, Y: VCC VRST (MAX),
ISOURCE = 30µA
0.8 × VCC
V
W: VCC VRST (MAX), ISOURCE = 20µA
0.8 × VCC
V
L, M: VCC VRST (MIN), ISINK = 3.2mA
0.4
V
T, S, R, Z, Y, W: VCC VRST (MIN),
ISINK = 1.2mA
0.3
V
TA = 0˚C to +70˚C, VCC = 1V, ISINK =50µA
0.3
V
VCC = 1.2V, ISINK =100µA
0.3
V
L, M: /RESET = 0V, VCC = 5.5V
800
µA
T, S, R, Z, Y, W: /RESET = 0V,
VCC = 3.6V
400
µA
VCC 1.6VISOURCE = 150µA
RESET Output Voltage
Low (VOL)
Watchdog Input (WDI)
L, M: VCC VRST (MAX), ISOURCE = 120µA
0.8 × VCC
V
L, M: VCC VRST (MAX), ISINK = 3.2mA
0.4
V
T, S, R, Z, Y, W: VCC VRST (MAX),
ISINK = 1.2mA
0.3
V
2.40
s
(8)
Watchdog Timeout
Period (tWD)
1.12
1.60
50
Watchdog Pulse Width
ns
0.3 ×
VCC
Watchdog Input Low
Voltage (VIL)
Watchdog Input High
Voltage (VIH)
Watchdog Input Current
January 14, 2014
0.7 × VCC
WDI = VCC
V
15
-20
WDI = 0V
6
V
-15
25
µA
µA
Revision 1.0
Micrel, Inc.
MAX823/4/5
Electrical Characteristics (Continued)(5)
VCC = 4.7V to 5.5V for MAX823/4/5L, VCC = 4.5V to 5.5V for MAX823/4/5M, VCC = 3.15V to 3.6V for MAX823/4/5T, VCC = 3.0V to 3.6V
for MAX823/4/5S, VCC = 2.7V to 3.6V for MAX823/4/5R, VCC = 2.38V to 2.75V for MAX823/4/5Z, VCC = 2.25V to 2.75V for
(6)
MAX823/4/5Y, VCC = 1.75V to 2.0V for MAX823/4/5W; TJ = +25˚C, bold values indicate –40˚C ≤ TJ ≤ +125˚C, unless otherwise noted.
Parameter
Condition
Min.
Typ.
Max.
Units
0.3 × VCC
V
Manual Reset Input (/MR)
Input Low Voltage (VIL)
Input High Voltage (VIH)
/MR Pulse Width
0.7 × VCC
V
1.0
µs
/MR Noise Immunity (pulse
width with no reset)
100
ns
/MR to RESET Delay
500
ns
35
/MR Internal Pull-Up Resistor
52
75
kΩ
Notes:
2. Exceeding the absolute maximum ratings may damage the device.
3. The device is not guaranteed to function outside its operating ratings.
4. Devices are ESD sensitive. Handling precautions are recommended. Human body model, 1.5kΩ in series with 100pF.
5. Specification for packaged product only.
6. Overtemperature limits are guaranteed by design and not product tested.
7. The /RESET short-circuit current is the maximum pull-up current when /RESET is driven low by µP bidirectional reset pin.
8. The WDI input is designed to drive a three-state output device with a 10µA maximum leakage current and a maximum capacitance of 200pF.
January 14, 2014
7
Revision 1.0
Micrel, Inc.
MAX823/4/5
Typical Characteristics
Supply Current
vs. Temperature
Supply Current
vs. Input Voltage
7
RESET TIMEOUT PERIOD (ms)
250
6
5
SUPPLY CURRENT (µA)
SUPPLY CURRENT (µA)
6
MAX823W
4
MAX824L
3
2
MAX825S
1
/MR = Open
WDI = Open
MAX824L, VCC = 5.5V
5
MAX823W, VCC = 2V
4
3
MAX825S, VCC = 3.25V
2
/MR = OPEN
WDI = OPEN
1
200
150
100
0
0
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
-20
0
20
40
60
80
100
120
-40
500
400
300
200
100
1.8
1.6
1.4
1.2
1
0.8
0.6
0.4
0.2
0
0
0
20
40
60
80
100 120 140
TEMPERATURE (°C)
January 14, 2014
20
40
60
80
100
120
1.06
RESET THRESHOLD VOLTAGE (V)
WATCHDOG TIMEOUT PERIOD (s)
600
0
Normalized Reset Threshold
vs. Temperature
2
700
-20
TEMPERATURE (°C)
Watchdog Timeout Period vs.
Temperature
800
-20
/MR = OPEN
WDI = OPEN
TEMPERATURE ( C)
/MR to RESET Delay
vs. Temperature
-40
50
0
-40
INPUT VOLTAGE (V)
/MR TO RESET DELAY (ns)
RESET Timeout Period
vs. Temperature
1.04
1.02
1
0.98
0.96
0.94
0.92
-40
-20
0
20
40
60
80
TEMPERATURE (°C)
8
100
120
-40
-20
0
20
40
60
80
100
120
TEMPERATURE (°C)
Revision 1.0
Micrel, Inc.
MAX823/4/5
Functional Diagram
Timing Diagram
January 14, 2014
9
Revision 1.0
Micrel, Inc.
MAX823/4/5
Functional Description
Design and Product Advantages
The MAX823/4/5 is series of a voltage supervisor reset
IC with a manual reset input, watchdog input, and dual
reset outputs. The MAX823/4/5 asserts and holds a reset
when the supply voltage falls below the factoryprogrammed threshold voltage, when /MR is at low logic
level, or when watchdog input times out. Reset is
asserted for a fixed reset timeout period after the supply
voltage increases above the rising threshold voltage or
when the manual reset input is asserted high.
The MAX823/4/5 features an active-low, push-pull reset
output (/RESET) and an active-high, push-pull reset
output (RESET). It also contains 52kΩ pull-up resistors
on the /MR input to make it easy to connect to
pushbutton inputs. The MAX823/4 also features a
watchdog input (WDI).
Figure 1. Manual Reset Function
When Functioning as a Voltage Supervisor
The /RESET pin is asserted whenever VCC falls below the
reset threshold voltage, VRST (VCC < VRST). The VCC pin
circuitry includes hysteresis to prevent /RESET or
RESET pin chattering due to noise. The /RESET pin
remains asserted for the duration of the reset timeout
delay (tRP) after VCC has risen above the reset threshold
voltage plus the hysteresis. The reset function ensures
that a microprocessor is properly reset and powers up in
a known condition after a power failure. The /RESET
remains valid with VCC as low as 1V. The RESET output
is a complement of the /RESET output.
Manual Reset Input (/MR)
The /MR input pin has integrated pull-up resistors to keep
the current consumption low when the pushbutton switch
is pressed.
Reset Outputs (/RESET and RESET)
There are two reset outputs: /RESET and RESET. Both
outputs are push-pull, which eliminates the need for pullup resistors. The RESET output is the inverse of the
/RESET output.
Asserting /RESET and RESET Outputs
When Functioning as a Manual Reset
The reset outputs /RESET and RESET are asserted
while the /MR pin is driven low. Both reset outputs remain
asserted for a factory-programmed reset timeout delay
time, tRP. The typical value of a reset timeout period is
200ms. The /RESET pin is driven low while the RESET
pin is driven high whenever /MR is pulled low.
Figure 2. Voltage Supervisor Function
January 14, 2014
10
Revision 1.0
Micrel, Inc.
MAX823/4/5
VCC Transient
The MAX823/4/5 is relatively immune to small negativegoing VCC glitches below the reset threshold. As shown in
Figure 4, the overdrive voltage is the difference between
the threshold voltage and the minimum point of the VCC
glitch. Typically, an overdrive of 100mV with duration of
2μs or less will not cause a reset.
Watchdog Input
The MAX823/4 has an on-chip watchdog timer that can
reset the microprocessor if it fails to strobe the WDI input
within a preset timeout period (tWD). If the WDI pin is left
unconnected, this function is disabled. The watchdog
timeout period starts when the reset outputs are
deasserted or either a high-to-low or low-to-high
transition occurs before the watchdog timeout period
(tWD). If the watchdog timer times out, then the reset
outputs will assert and stay asserted for a reset timeout
period (tRP). The watchdog timer is also cleared whenever
the reset outputs are asserted by /MR, or if VCC falls
below VRST. The watchdog timer starts again whenever
the reset outputs are de-asserted.
Figure 4. VCC Transient
Reset Valid up to VCC = 1V
The MAX823/4/5 is a supervisory circuit that monitors the
power supply voltage level. If the power supply voltage
level falls below the factory-programmed threshold level,
then the reset signals are asserted. The MAX823/4/5
maintains the reset states with VCC as low as 1V.
Supply Bypass Capacitor
An optional 0.1µF input bypass capacitor can be placed
from VCC (Pin 6) to GND (Pin 2) to increase glitch
rejection and provides additional transient immunity.
Figure 3. Watchdog Input
Watchdog Input Current
The WDI input current is the current sourced or sinked by
the WDI pin when the WDI input is driven low or high,
respectively. The WDI input is designed to drive a tristate output device with a 10µA maximum leakage
current and a maximum capacitance of 200pF.
January 14, 2014
11
Revision 1.0
Micrel, Inc.
MAX823/4/5
Typical Applications
Figure 5. MAX825 for Precision Power Good Function
Figure 6. MAX823 Used for Load Switch
Figure 7. MAX824 Used for Microcontroller Reset with Watchdog Input
January 14, 2014
12
Revision 1.0
Micrel, Inc.
MAX823/4/5
Package Information(9)
5-Pin SOT23 (EUK)
January 14, 2014
13
Revision 1.0
Micrel, Inc.
MAX823/4/5
Package Information (Continued)(9)
5-Pin SC70 (EXK)
Note:
9. Package information is correct as of the publication date. For updates and the most current information, go to www.micrel.com.
MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA
TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http://www.micrel.com
Micrel makes no representations or warranties with respect to the accuracy or completeness of the information furnished in this data sheet. This
information is not intended as a warranty and Micrel does not assume responsibility for its use. Micrel reserves the right to change circuitry,
specifications and descriptions at any time without notice. No license, whether express, implied, arising by estoppel or otherwise, to any intellectual
property rights is granted by this document. Except as provided in Micrel’s terms and conditions of sale for such products, Micrel assumes no liability
whatsoever, and Micrel disclaims any express or implied warranty relating to the sale and/or use of Micrel products including liability or warranties
relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right.
Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product
can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical
implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A
Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully
indemnify Micrel for any damages resulting from such use or sale.
© 2014 Micrel, Incorporated.
January 14, 2014
14
Revision 1.0