LINER LTC3400-1 600ma, 1.2mhz micropower synchronous boost converter in thinsot Datasheet

LTC3400-1
600mA, 1.2MHz Micropower
Synchronous Boost Converter
in ThinSOT
U
FEATURES
DESCRIPTIO
■
The LTC®3400-1 is a synchronous, fixed frequency, stepup DC/DC converter delivering high efficiency in a 6-lead
ThinSOT™ package. Capable of supplying 3.3V at 100mA
from a single AA cell input, the device contains an internal
NMOS switch and PMOS synchronous rectifier.
■
■
■
■
■
■
■
■
■
■
Up to 92% Efficiency
Generates 3.3V at 100mA from a Single AA Cell
Low Start-Up Voltage: 0.85V
VOUT Connected to VIN in Shutdown
Internal Synchronous Rectifier
2.5V to 5V Output Range
Automatic Burst Mode® Operation
Logic Controlled Shutdown (< 1µA)
Antiringing Control Minimizes EMI
Tiny External Components
Low Profile (1mm) SOT-23 Package
A switching frequency of 1.2MHz minimizes solution
footprint by allowing the use of tiny, low profile inductors
and ceramic capacitors. The current mode PWM design is
internally compensated, reducing external parts count.
The LTC3400-1 features automatic shifting to power saving Burst Mode operation at light loads. In shutdown, VOUT
and VIN are connected, which allows the input battery to be
used for backup power. The LTC3400-1 features low
shutdown current of under 1µA.
U
APPLICATIO S
■
■
■
■
■
■
Pagers
MP3 Players
Digital Cameras
LCD Bias Supplies
Handheld Instruments
Wireless Handsets
GPS Receivers
The LTC3400-1 is offered in the low profile (1mm)
SOT-23 package.
, LTC, LT and Burst Mode are registered trademarks of Linear Technology Corporation.
ThinSOT is a trademark of Linear Technology Corporation.
US Patent Numbers 5,481,178; 6,580,258; 6,304,066; 6,127,815; 6,498,466; 6,611,131.
U
■
TYPICAL APPLICATIO
Efficiency
100
Single Cell to 3.3V Synchronous Boost Converter
90
VIN = 2.4V
+
SINGLE
AA CELL
4.7µF
SW
VIN
VOUT
LTC3400-1
OFF ON
SHDN
GND
1.02M
1%
FB
VOUT
3.3V
100mA
EFFICIENCY (%)
4.7µH
VIN = 1.5V
80
70
60
4.7µF
604k
1%
50
34001 F01
FIGURE 1 CIRCUIT
WITH OPTIONAL SCHOTTKY DIODE
(SEE APPLICATIONS INFORMATION)
40
0.1
1
10
100
LOAD CURRENT (mA)
1000
34001 F01a
34001f
1
LTC3400-1
W W
W
AXI U
U
ABSOLUTE
RATI GS
U
U
W
PACKAGE/ORDER I FOR ATIO
(Note 1)
VIN Voltage ................................................. – 0.3V to 6V
SW Voltage
DC .......................................................... – 0.3V to 6V
Pulsed (<100ns) ......................................– 0.3V to 7V
SHDN, FB Voltage ....................................... – 0.3V to 6V
VOUT ........................................................... – 0.3V to 6V
Operating Temperature Range (Note 2) .. – 30°C to 85°C
Storage Temperature Range ................... – 65°C to 125°
Lead Temperature (Soldering, 10 sec).................. 300°C
ORDER PART
NUMBER
TOP VIEW
SW 1
GND 2
FB 3
6 VIN
LTC3400ES6-1
5 VOUT
4 SHDN
S6 PART MARKING
S6 PACKAGE
6-LEAD PLASTIC TSOT-23
LTBJM
TJMAX = 125°C, θJC = 102°C/W
Consult LTC Marketing for parts specified with wider operating temperature ranges.
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VIN = 1.2V, VOUT = 3.3V, unless otherwise specified.
PARAMETER
CONDITIONS
Minimum Start-Up Voltage
ILOAD = 1mA
Minimum Operating Voltage
SHDN = VIN (Note 4)
MIN
Output Voltage Adjust Range
TYP
MAX
0.85
1
0.5
0.65
V
5
V
1.268
V
2.5
●
Feedback Voltage
1.192
1.23
UNITS
V
Feedback Input Current
VFB = 1.25V (Note 3)
1
Quiescent Current (Burst Mode Operation)
VFB = 1.4V (Note 5)
19
30
µA
Quiescent Current (Shutdown)
VSHDN = 0V, Not Including Switch Leakage, VIN = VOUT
0.01
1
µA
Quiescent Current (Active)
Measured On VOUT
300
500
µA
NMOS Switch Leakage
VSW = 5V
0.1
5
µA
PMOS Switch Leakage
VSW = 0V (Note 3)
0.1
µA
NMOS Switch On Resistance
VOUT = 3.3V
VOUT = 5V
0.35
0.20
Ω
Ω
PMOS Switch On Resistance
VOUT = 3.3V
VOUT = 5V
0.45
0.30
Ω
Ω
850
mA
NMOS Current Limit
600
nA
Burst Mode Operation Current Threshold
(Note 3)
3
mA
Current Limit Delay to Output
(Note 3)
40
ns
Max Duty Cycle
VFB = 1.15V
●
80
87
●
0.95
0.85
1.2
1.2
Switching Frequency
SHDN Input High
MHz
MHz
1
V
SHDN Input Low
SHDN Input Current
%
1.5
1.5
VSHDN = 5.5V
Note 1: Absolute Maximum Ratings are those values beyond which the life
of a device may be impaired.
Note 2: The LTC3400-1 is guaranteed to meet performance specifications
from 0°C to 70°C. Specifications over the – 30°C to 85°C operating
temperature range are assured by design, characterization and correlation
with statistical process controls.
0.01
0.35
V
1
µA
Note 3: Specification is guaranteed by design and not 100% tested in
production.
Note 4: Minimum VIN operation after start-up is only limited by the
battery’s ability to provide the necessary power as it enters a deeply
discharged state.
Note 5: Burst Mode operation IQ is measured at VOUT. Multiply this value
by VOUT/VIN to get the equivalent input (battery) current.
34001f
2
LTC3400-1
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Output Load Burst Mode Threshold
vs VIN
Minimum Start-Up Voltage
vs Load Current
VOUT vs Temperature
3.36
L = 4.7µH
TA = 25°C
1.4
FIGURE 1 CIRCUIT
IO = 10mA
1.3
START-UP VOLTAGE (V)
VOUT = 3.3V
VOUT = 5V
3.32
VOUT (V)
OUTPUT CURRENT (mA)
3.34
20
3.30
10
3.28
0.9
1.5
2.1
2.7
VIN (V)
3.3
3.9
3.24
–60
4.5
1.1
1.0
0.8
–30
0
30
60
TEMPERATURE (°C)
90
0.1
120
1
10
IOUT (mA) CURRENT SOURCE LOAD
Normalized Oscillator Frequency
vs Temperature
No Load Battery Current vs VBATT
100
3400 G03
3400 G02
3400 G01
1000
1.2
0.9
3.26
0
TA = 25°C
SW Pin Antiringing Operation
1.01
VOUT = 3.3V
TA = 25°C
NORMALIZED FREQUENCY
BATTERY CURRENT (µA)
1.00
100
0.99
VSW
1V/DIV
0.98
0.97
0V
0.96
10
0.9
1.2
1.5 1.8 2.1 2.4
BATTERY VOLTAGE (V)
2.7
0.95
–50 –30
3.0
30
50
–10 10
TEMPERATURE (°C)
SW Pin Fixed Frequency,
Continuous Inductor Current
Operation
Fixed Frequency and Burst Mode
Operation
VSW
1V/DIV
3400 G07
3400 G06
VOUT Transient Response
VOUT(AC)
100mV/DIV
VOUT(AC)
100mV/DIV
60mA
100mA
IOUT
40mA
IOUT
0V
100ns/DIV
90
100ns/DIV
3400 G05
3400 G04
VIN = 1.3V
VOUT = 3.3V
IOUT = 50mA
L = 6.8µH
COUT = 4.7µF
70
VIN = 1.3V
VOUT = 3.3V
IOUT = 10mA
L = 6.8µH
COUT = 4.7µF
10µA
VIN = 1.3V
10ms/DIV
VOUT = 3.3V
IOUT = 60mA TO 10µA
L = 6.8µH
COUT = 4.7µF
3400 G08
VIN = 1.3V
100µs/DIV
VOUT = 3.3V
IOUT = 40mA TO 100mA
L = 6.8µH
COUT = 4.7µF
3400 G09
34001f
3
LTC3400-1
U
U
U
PI FU CTIO S
SHDN = Low: Shutdown, quiescent current < 1µA.
100Ω connected between SW and VIN. VIN is connected
to VOUT through the internal P-channel MOSFET synchronous rectifier and external inductor.
SW (Pin 1): Switch Pin. Connect inductor between SW
and VIN. Optional Schottky diode is connected between
SW and VOUT. Keep these PCB trace lengths as short and
wide as possible to reduce EMI and voltage overshoot. If
the inductor current falls to zero, or SHDN is low, an
internal 100Ω antiringing switch is connected from SW to
VIN to minimize EMI.
Typically, SHDN should be connected to VIN through a 1M
pull-up resistor.
VOUT (Pin 5): Output Voltage Sense Input and Drain of the
Internal Synchronous Rectifier MOSFET. Bias is derived
from VOUT. PCB trace length from VOUT to the output filter
capacitor(s) should be as short and wide as possible. VOUT
is connected to VIN in shutdown through the internal
P-channel MOSFET synchronous rectifier.
GND (Pin 2): Signal and Power Ground. Provide a short
direct PCB path between GND and the (–) side of the output
capacitor(s).
FB (Pin 3): Feedback Input to the gm Error Amplifier.
Connect resistor divider tap to this pin. The output voltage
can be adjusted from 2.5V to 5V by:
VIN (Pin 6): Battery Input Voltage. The device gets its
start-up bias from VIN. Once VOUT exceeds VIN, bias
comes from VOUT. Thus, once started, operation is completely independent from VIN. Operation is only limited by
the output power level and the battery’s internal series
resistance.
VOUT = 1.23V • [1 + (R1/R2)]
SHDN (Pin 4): Logic Controlled Shutdown Input.
SHDN = High: Normal free running operation, 1.2MHz
typical operating frequency.
W
BLOCK DIAGRA
L1
4.7µH
SINGLE
CELL
INPUT
CIN
1µF
6 VIN
1 SW
OPTIONAL
SCHOTTKY
+
+
VOUT
GOOD
–
START-UP
OSC
A
2.3V
A/B
MUX
PWM
CONTROL
RAMP
GEN
1.2MHz
3.3V
OUTPUT
VOUT
0.45Ω
B
5
SYNC
DRIVE
CONTROL
SHUTDOWN
CURRENT
SENSE
Σ
SLOPE
COMP
0.35Ω
R1
1.02M
1%
(EXTERNAL)
CFF
(OPTIONAL)
PWM
COMPARATOR
–
–
+
FB
–
SLEEP
Burst Mode
OPERATION
CONTROL
CC
150pF
SHDN
4
SHUTDOWN
CONTROL
SHUTDOWN
+
RC
80k
gm
ERROR
AMP
CP2
2.5pF
COUT
4.7µF
3
1.23V
REF
R2
604k
1%
(EXTERNAL)
2 GND
34001 BD
34001f
4
LTC3400-1
U
OPERATIO
The LTC3400-1 is a1.2MHz, synchronous boost converter
housed in a 6-lead ThinSOT package. Able to operate from
an input voltage below 1V, the device features fixed
frequency, current mode PWM control for exceptional line
and load regulation. With its low RDS(ON) and gate charge
internal MOSFET switches, the device maintains high
efficiency over a wide range of load current. Detailed
descriptions of the three distinct operating modes follow.
Operation can be best understood by referring to the Block
Diagram.
Low Voltage Start-Up
The LTC3400-1 will start up at a typical VIN voltage of
0.85V or higher. The low voltage start-up circuitry controls
the internal NMOS switch up to a maximum peak inductor
current of 850mA (typ), with an approximate 1.5µs offtime during start-up, allowing the device to start up into an
output load. Once VOUT exceeds 2.3V, the start-up circuitry is disabled and normal fixed frequency PWM operation is initiated. In this mode, the LTC3400-1 operates
independent of VIN, allowing extended operating time as
the battery can droop to several tenths of a volt without
affecting output voltage regulation. The limiting factor for
the application becomes the ability of the battery to supply
sufficient energy to the output.
Low Noise Fixed Frequency Operation
Oscillator: The frequency of operation is internally set to
1.2MHz.
Error Amp: The error amplifier is an internally compensated
transconductance type (current output) with a transconductance (gm) = 33 microsiemens. The internal 1.23V reference
voltage is compared to the voltage at the FB pin to generate
an error signal at the output of the error amplifier. A voltage divider from VOUT to ground programs the output
voltage via FB from 2.5V to 5V using the equation:
VOUT = 1.23V • [1 + (R1/R2)]
Current Sensing: A signal representing NMOS switch
current is summed with the slope compensator. The
summed signal is compared to the error amplifier output
to provide a peak current control command for the PWM.
Peak switch current is limited to approximately 850mA
independent of input or output voltage. The current signal
is blanked for 40ns to enhance noise rejection.
Zero Current Comparator: The zero current comparator
monitors the inductor current to the output and shuts off
the synchronous rectifier once this current reduces to approximately 20mA. This prevents the inductor current from
reversing in polarity improving efficiency at light loads.
Antiringing Control: The antiringing control circuitry prevents high frequency ringing of the SW pin as the inductor
current goes to zero by damping the resonant circuit
formed by L and CSW (capacitance on SW pin).
Burst Mode Operation
Portable devices frequently spend extended time in low
power or standby mode, only switching to high power
drain when specific functions are enabled. In order to
improve battery life in these types of products, high power
converter efficiency needs to be maintained over a wide
output power range. In addition to its high efficiency at
moderate and heavy loads, the LTC3400-1 includes automatic Burst Mode operation that improves efficiency of
the power converter at light loads. Burst mode operation
is initiated if the output load current falls below an
internally programmed threshold (see Typical Performance graph, Output Load Burst Mode Threshold vs V IN).
Once initiated, the Burst Mode operation circuitry shuts
down most of the device, only keeping alive the circuitry
required to monitor the output voltage. This is referred to
as the sleep state. In sleep, the LTC3400-1 draws only
19µA from the output capacitor, greatly enhancing efficiency. When the output voltage has drooped approximately 1% from nominal, the LTC3400-1 wakes up and
commences normal PWM operation. The output capacitor
recharges and causes the LTC3400-1 to reenter sleep if
the output load remains less than the sleep threshold. The
frequency of this intermittent PWM or burst operation is
proportional to load current; that is, as the load current
drops further below the burst threshold, the LTC3400-1
turns on less frequently. When the load current increases
34001f
5
LTC3400-1
U
OPERATIO
above the burst threshold, the LTC3400-1 will resume
continuous PWM operation seamlessly. Referring to the
Block Diagram, an optional capacitor (CFF) between VOUT
and FB in some circumstances can reduce the peak-to-
peak VOUT ripple and input quiescent current during Burst
Mode operation. Typical values for CFF range from 15pF to
220pF.
U
W
U U
APPLICATIO S I FOR ATIO
PCB LAYOUT GUIDELINES
The high speed operation of the LTC3400-1 demands
careful attention to board layout. You will not get advertised performance with careless layout. Figure 1 shows
the recommended component placement. A large ground
pin copper area will help to lower the chip temperature. A
multilayer board with a separate ground plane is ideal, but
not absolutely necessary.
will allow greater output current capability by reducing the
inductor ripple current. Increasing the inductance above
10µH will increase size while providing little improvement
in output current capability.
The approximate output current capability of the LTC3400-1
versus inductance value is given in the equation below and
illustrated graphically in Figure 2.
VIN =1.2V
180
VIN
1
SW
2
GND VOUT 5
3
OUTPUT CURRENT (mA)
(OPTIONAL)
VIN 6
FB SHDN 4
SHDN
VOUT = 3V
VOUT = 3.3V
160
VOUT = 3.6V
140
120
VOUT = 5V
110
80
60
VOUT
3
5
7
9 11 13 15 17 19 21 23
INDUCTANCE (µH)
34001 F03
34001 F02
RECOMMENDED COMPONENT PLACEMENT. TRACES
CARRYING HIGH CURRENT ARE DIRECT. TRACE AREA AT
FB PIN IS SMALL. LEAD LENGTH TO BATTERY IS SHORT
Figure 1. Recommended Component Placement
for Single Layer Board
COMPONENT SELECTION
Inductor Selection
The LTC3400-1 can utilize small surface mount and chip
inductors due to its fast 1.2MHz switching frequency. A
minimum inductance value of 3.3µH is necessary for 3.6V
and lower voltage applications and 4.7µH for output
voltages greater than 3.6V. Larger values of inductance
Figure 2. Maximum Output Current vs
Inductance Based On 90% Efficiency
V •D⎞
⎛
IOUT(MAX) = η • ⎜IP – IN ⎟ • (1 – D)
⎝
f • L • 2⎠
where:
η = estimated efficiency
IP = peak current limit value (0.6A)
VIN = input (battery) voltage
D = steady-state duty ratio = (VOUT – VIN)/VOUT
f = switching frequency (1.2MHz typical)
L = inductance value
34001f
6
LTC3400-1
U
W
U U
APPLICATIO S I FOR ATIO
The inductor current ripple is typically set for 20% to 40%
of the maximum inductor current (IP). High frequency
ferrite core inductor materials reduce frequency dependent power losses compared to cheaper powdered iron
types, improving efficiency. The inductor should have low
ESR (series resistance of the windings) to reduce the I2R
power losses, and must be able to handle the peak
inductor current without saturating. Molded chokes and
some chip inductors usually do not have enough core to
support the peak inductor currents of 850mA seen on the
LTC3400-1. To minimize radiated noise, use a toroid, pot
core or shielded bobbin inductor. See Table 1 for some
suggested components and suppliers.
Table 1. Recommended Inductors
PART
L
(µH)
MAX
DCR
mΩ
HEIGHT
(mm)
2.0
2.0
1.8
1.8
3.5
3.5
0.8
0.8
Sumida
(847) 956-0666
www.sumida.com
VENDOR
extremely low ESR and are available in small footprints. A
2.2µF to 10µF output capacitor is sufficient for most
applications. Larger values up to 22µF may be used to
obtain extremely low output voltage ripple and improve
transient response. An additional phase lead capacitor
may be required with output capacitors larger than 10µF
to maintain acceptable phase margin. X5R and X7R
dielectric materials are preferred for their ability to maintain capacitance over wide voltage and temperature ranges.
Low ESR input capacitors reduce input switching noise
and reduce the peak current drawn from the battery. It
follows that ceramic capacitors are also a good choice for
input decoupling and should be located as close as possible to the device. A 4.7µF input capacitor is sufficient for
virtually any application. Larger values may be used without limitations. Table 2 shows a list of several ceramic
capacitor manufacturers. Consult the manufacturers directly for detailed information on their entire selection of
ceramic parts.
CDRH5D18-4R1
CDRH5D18-100
CDRH3D16-4R7
CDRH3D16-6R8
CR43-4R7
CR43-100
CMD4D06-4R7MC
CMD4D06-3R3MC
4.1
10
4.7
4.7
10
4.7
3.3
57
124
105
170
109
182
216
174
DS1608-472
DS1608-103
DO1608C-472
4.7
10
4.7
60
75
90
2.9
2.9
2.9
Coilcraft
(847) 639-6400
www.coilcraft.com
D52LC-4R7M
D52LC-100M
4.7
10
84
137
2.0
2.0
Toko
(408) 432-8282
www.tokoam.com
Output Diode
LQH3C4R7M24
4.7
195
2.2
Murata
www.murata.com
Table 2. Capacitor Vendor Information
Output and Input Capacitor Selection
Low ESR (equivalent series resistance) capacitors should
be used to minimize the output voltage ripple. Multilayer
ceramic capacitors are an excellent choice as they have
SUPPLIER
PHONE
WEBSITE
AVX
(803) 448-9411
www.avxcorp.com
Murata
(714) 852-2001
www.murata.com
Taiyo Yuden
(408) 573-4150
www.t-yuden.com
Use a Schottky diode such as an MBR0520L, PMEG2010EA,
1N5817 or equivalent if the converter output voltage is 4.5V
or greater. The Schottky diode carries the output current for
the time it takes for the synchronous rectifier to turn on. Do
not use ordinary rectifier diodes, since the slow recovery
times will compromise efficiency. A Schottky diode is also
strongly recommended for output voltages below 4.5V,
and will increase converter efficiency by 2% to 3%.
34001f
7
LTC3400-1
U
TYPICAL APPLICATIO S
Single Cell to 3.3V Synchronous Boost Converter
with Load Disconnect in Shutdown
L1
4.7µH
+
SINGLE
AA CELL
C1
4.7µF
D1
1
6
SW
VIN
VOUT
5
LTC3400-1
OFF ON
4
SHDN
FB
GND
2
D1: PHILLIPS PMEG2010EA
L1: SUMIDA CDRH2D18/HP-4R7
R3
510k
M1
Si2305DS
R3
510k
R1
1.02M
1%
C2
4.7µF
R2
604k
1%
3
VOUT
3.3V
100mA
Q1
2N3904
34001 TA01a
34001f
8
LTC3400-1
U
TYPICAL APPLICATIO S
Single Lithium Cell to 5V, 250mA
OPTIONAL
SNUBBER
2Ω
1nF
L1
4.7µH
+
LITHIUM
CELL
C1
4.7µF
D1
1
6
SW
VIN
VOUT
5
LTC3400-1
OFF ON
4
SHDN
FB
3
C2
4.7µF
GND
2
D1: PHILIPS PMEG2010EA
L1: SUMIDA CDRH2D18/HP-4R7
C1, C2: TAIYO YUDEN JMK212BJ475MG
R1
1.02M
1%
C3
100pF
R2
332k
1%
34001 TA02a
3.6V to 5V Efficiency
100
EFFICIENCY (%)
90
LTC3400-1
CO = 4.7µF
L = 4.7µH
80
70
60
50
0.1
1
10
100
LOAD CURRENT (mA)
1000
34001 TA02b
34001f
9
LTC3400-1
U
TYPICAL APPLICATIO S
Single Cell AA Cell to ±3V Synchronous Boost Converter
C3
1µF
L1
4.7µH
+
SINGLE
AA CELL
C1
4.7µF
1
6
SW
VIN
VOUT
5
LTC3400-1
OFF ON
4
FB
SHDN
GND
2
3
R1
1.02M
1%
R2
715k
1%
D1
D2
VOUT1
3V
C2
90mA
4.7µF
C4
10µF
34001 TA03a
VOUT2
–3V
10mA
D1, D2: ZETEX FMND7000 DUAL DIODE
L1: SUMIDA CDRH2D18/HP-4R7
34001f
10
LTC3400-1
U
PACKAGE DESCRIPTIO
S6 Package
6-Lead Plastic TSOT-23
(Reference LTC DWG # 05-08-1636)
0.62
MAX
2.90 BSC
(NOTE 4)
0.95
REF
1.22 REF
3.85 MAX 2.62 REF
1.4 MIN
2.80 BSC
1.50 – 1.75
(NOTE 4)
PIN ONE ID
RECOMMENDED SOLDER PAD LAYOUT
PER IPC CALCULATOR
0.30 – 0.45
6 PLCS (NOTE 3)
0.95 BSC
0.80 – 0.90
0.20 BSC
0.01 – 0.10
1.00 MAX
DATUM ‘A’
0.30 – 0.50 REF
0.09 – 0.20
(NOTE 3)
1.90 BSC
S6 TSOT-23 0302
NOTE:
1. DIMENSIONS ARE IN MILLIMETERS
2. DRAWING NOT TO SCALE
3. DIMENSIONS ARE INCLUSIVE OF PLATING
4. DIMENSIONS ARE EXCLUSIVE OF MOLD FLASH AND METAL BURR
5. MOLD FLASH SHALL NOT EXCEED 0.254mm
6. JEDEC PACKAGE REFERENCE IS MO-193
34001f
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
11
LTC3400-1
U
TYPICAL APPLICATIO
Single AA Cell to 2.5V Synchronous Boost Converter
L1
3.3µH
+
SINGLE
AA CELL
C1
4.7µF
D1
1
6
SW
VIN
VOUT
LTC3400-1
OFF ON
4
SHDN
FB
3
GND
D1: PHILIPS PMEG2010EA
L1: SUMIDA CDRH2D18/HP-3R7
VOUT
2.5V
130mA
5
2
R1
1.02M
1%
R2
1M
1%
C2
4.7µF
34001 TA04a
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
LT1308A/LT1308B
High Current, Micropower, Single Cell 600kHz DC/DC Converter
5V at 1A with Single Li-Ion Cell, VOUT to 34V
LT1613
1.4MHz, Single Cell DC/DC Converter in ThinSOT
VIN as Low as 1.1V, 3V at 30mA from Single Cell
LT1615
Micropower Step-Up DC/DC Converter in ThinSOT
IQ = 20µA, 1µA Shutdown Current, VIN as Low as 1V
LT ®1618
1.4MHz Step-Up DC/DC Converter with Current Limit
1.5A Switch, 1.6V to 18V Input Range,
Input or Output Current Limiting
LT1619
High Efficiency Boost DC/DC Controller
1A Gate Drive, 1.1V to 20V Input, Separate VCC for Gate Drive
LTC1872
ThinSOT Boost DC/DC Controller
50kHz, 2.5V to 9.8V Input
LT1930/LT1930A
1.2MHz/2.2MHz DC/DC Converters in ThinSOT
VIN = 2.6V to 16V, 5V at 450mA from 3.3V Input
LT1932
Constant Current Step-Up LED Driver
Drives Up to Eight White LEDs, ThinSOT Package
LT1946/LT1946A
1.2MHz/2.7MHz Boost DC/DC Converters
1.5A, 36V Internal Switch, 8-Pin MSOP Package
LT1949
600kHz, 1A Switch PWM DC/DC Converter
1A, 0.5Ω, 30V Internal Switch, VIN as Low as 1.5V,
Low-Battery Detect Active in Shutdown
LTC3400/LTC3400B
600mA, 1.2MHz Synchronous Boost Converters in ThinSOT
Up to 92% EFFiciency, 600mA Switch,
No Burst Option (LTC3400B)
LTC3401
1A, 3MHz Micropower Synchronous Boost Converter
1A Switch, Programmable Frequency, 10-Pin MSOP Package
LTC3402
2A, 3MHz Micropower Synchronous Boost Converter
2A Switch, Programmable Frequency, 10-Pin MSOP Package
LTC3421
3A, 3MHz Micropower Synchronous Boost Converter
Up to 96% Efficiency, 3A Switch, True Output Disconnect,
4mm x 4mm QFN Package
LTC3423
1A, 3MHz Micropower Synchronous Boost Converter
1A Switch, Separate Bias Pin for Low Output Voltages
LTC3424
2A, 3MHz Micropower Synchronous Boost Converter
2A Switch, Separate Bias Pin for Low Output Voltages
LTC3425
5A, 8MHz, 4-Phase Micropower Synchronous Boost Converter
Up to 95% Efficiency, 5A Switch, True Output
Disconnect, IQ = 12µA, QFN Package
LTC3429
600mA, 500kHz Synchronous Boost Converter in ThinSOT
Up to 96% Efficiency, 600mA Switch, True Output
Disconnect, Soft Start
34001f
12
Linear Technology Corporation
LT/TP 0604 1K • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com
© LINEAR TECHNOLOGY CORPORATION 2004
Similar pages