PHILIPS HEF4052BT Dual 4-channel analog multiplexer/demultiplexer Datasheet

HEF4052B
Dual 4-channel analog multiplexer/demultiplexer
Rev. 8 — 17 November 2011
Product data sheet
1. General description
The HEF4052B is a dual 4-channel analog multiplexer/demultiplexer with common
channel select logic. Each multiplexer/demultiplexer has four independent inputs/outputs
(nY0 to nY3) and a common input/output (nZ). The common channel select logic includes
two select inputs (S1 and S2) and an active LOW enable input (E). Both
multiplexers/demultiplexers contain four bidirectional analog switches, each with one side
connected to an independent input/output (nY0 to nY3) and the other side connected to a
common input/output (nZ). With E LOW, one of the four switches is selected
(low-impedance ON-state) by S1 and S2. With E HIGH, all switches are in the
high-impedance OFF-state, independent of S1 and S2. If break before make is needed,
then it is necessary to use the enable input.
VDD and VSS are the supply voltage connections for the digital control inputs (S1 and S2,
and E). The VDD to VSS range is 3 V to 15 V. The analog inputs/outputs (nY0 to nY3, and
nZ) can swing between VDD as a positive limit and VEE as a negative limit. VDD  VEE may
not exceed 15 V. Unused inputs must be connected to VDD, VSS, or another input. For
operation as a digital multiplexer/demultiplexer, VEE is connected to VSS (typically
ground). VEE and VSS are the supply voltage connections for the switches.
2. Features and benefits





Fully static operation
5 V, 10 V, and 15 V parametric ratings
Standardized symmetrical output characteristics
Specified from 40 C to +85 C and 40 C to +125 C
Complies with JEDEC standard JESD 13-B
3. Applications
 Analog multiplexing and demultiplexing
 Digital multiplexing and demultiplexing
 Signal gating
HEF4052B
NXP Semiconductors
Dual 4-channel analog multiplexer/demultiplexer
4. Ordering information
Table 1.
Ordering information
All types operate from 40 C to +125 C.
Type number
Package
Name
Description
Version
HEF4052BP
DIP16
plastic dual in-line package; 16 leads (300 mil)
SOT38-4
HEF4052BT
SO16
plastic small outline package; 16 leads; body width 3.9 mm
SOT109-1
HEF4052BTT
TSSOP16
plastic thin shrink small outline package; 16 leads; body width 4.4 mm
SOT403-1
5. Functional diagram
VDD
16
13
12
14
15
S1
10
11
S2
9
LOGIC
LEVEL
CONVERSION
1 - OF - 4
DECODER
1
5
E
1Z
1Y0
1Y1
1Y2
1Y3
2Y0
2Y1
6
2
4
3
8
7
VSS
VEE
2Y2
2Y3
2Z
mnb042
Fig 1.
Functional diagram
HEF4052B
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 17 November 2011
© NXP B.V. 2011. All rights reserved.
2 of 22
HEF4052B
NXP Semiconductors
Dual 4-channel analog multiplexer/demultiplexer
nYn
VDD
VDD
nZ
VEE
001aak604
Fig 2.
Schematic diagram (one switch)
10
9
13
6
0
1
4×
0
3
G4
1Z
1Y0
12
10
S1
1Y1
14
9
S2
1Y2
15
1Y3
11
2
2Y0
1
3
6
E
2Y1
5
2Y2
2
2Y3
4
MDX
3
0
1
Fig 3. Logic symbol
HEF4052B
Product data sheet
5
2
4
12
14
13
15
2Z
3
1
11
001aak605
mnb041
Fig 4. IEC logic symbol
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 17 November 2011
© NXP B.V. 2011. All rights reserved.
3 of 22
HEF4052B
NXP Semiconductors
Dual 4-channel analog multiplexer/demultiplexer
1Z
1Y0
S1
LEVEL
CONVERTER
1Y1
S2
LEVEL
CONVERTER
1Y2
E
LEVEL
CONVERTER
1Y3
2Y0
2Y1
2Y2
2Y3
2Z
001aak634
Fig 5.
Logic diagram
HEF4052B
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 17 November 2011
© NXP B.V. 2011. All rights reserved.
4 of 22
HEF4052B
NXP Semiconductors
Dual 4-channel analog multiplexer/demultiplexer
6. Pinning information
6.1 Pinning
HEF4052B
2Y0
1
16 VDD
2Y2
2
15 1Y2
2Z
3
14 1Y1
HEF4052B
2Y3
4
13 1Z
2Y1
5
12 1Y0
E
VEE
VSS
6
11 1Y3
7
10 S1
9
8
S2
2Y0
1
2Y2
2
16 VDD
15 1Y2
2Z
3
14 1Y1
2Y3
4
13 1Z
2Y1
5
12 1Y0
E
6
11 1Y3
VEE
7
10 S1
VSS
8
S2
001aak606
001aag215
Fig 6.
9
Pin configuration SOT38-4 and SOT109-1
Fig 7.
Pin configuration SOT338-1 and SOT403-1
6.2 Pin description
Table 2.
Pin description
Symbol
Pin
Description
E
6
enable input (active LOW)
VEE
7
supply voltage
VSS
8
ground supply voltage
S1, S2
10, 9
select input
1Y0, 1Y1, 1Y2, 1Y3, 2Y0, 2Y1, 2Y2, 2Y3 12, 14, 15, 11, 1, 5, 2, 4
independent input or output
1Z, 2Z
13, 3
common output or input
VDD
16
supply voltage
HEF4052B
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 17 November 2011
© NXP B.V. 2011. All rights reserved.
5 of 22
HEF4052B
NXP Semiconductors
Dual 4-channel analog multiplexer/demultiplexer
7. Functional description
7.1 Function table
Table 3.
Function table[1]
Input
Channel on
E
S2
S1
L
L
L
nY0 to nZ
L
L
H
nY1 to nZ
L
H
L
nY2 to nZ
L
H
H
nY3 to nZ
H
X
X
switches off
[1]
H = HIGH voltage level;
L = LOW voltage level;
X = don’t care.
8. Limiting values
Table 4.
Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to VSS = 0 V (ground).
Symbol
Parameter
VDD
supply voltage
Conditions
[1]
Min
Max
Unit
0.5
+18
V
18
+0.5
V
-
10
mA
VEE
supply voltage
referenced to VDD
IIK
input clamping current
pins Sn and E;
VI < 0.5 V or VI > VDD + 0.5 V
VI
input voltage
0.5
VDD + 0.5
V
II/O
input/output current
-
10
mA
IDD
supply current
-
50
mA
Tstg
storage temperature
65
+150
C
Tamb
ambient temperature
40
+125
C
total power dissipation
Ptot
P
[1]
[2]
power dissipation
Tamb = 40 C to +125 C
[2]
DIP16 package
-
750
mW
SO16 package
-
500
mW
TSSOP16 package
-
500
mW
-
100
mW
per output
To avoid drawing VDD current out of terminal Z, when switch current flows into terminals Y, the voltage drop across the bidirectional
switch must not exceed 0.4 V. If the switch current flows into terminal Z, no VDD current will flow out of terminals Y, and in this case there
is no limit for the voltage drop across the switch, but the voltages at Y and Z may not exceed VDD or VEE.
For DIP16 package: Ptot derates linearly with 12 mW/K above 70 C.
For SO16 package: Ptot derates linearly with 8 mW/K above 70 C.
For SSOP16 package: Ptot derates linearly with 5.5 mW/K above 60 C.
HEF4052B
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 17 November 2011
© NXP B.V. 2011. All rights reserved.
6 of 22
HEF4052B
NXP Semiconductors
Dual 4-channel analog multiplexer/demultiplexer
9. Recommended operating conditions
Table 5.
Recommended operating conditions
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
VDD
supply voltage
see Figure 8
3
-
15
V
VI
input voltage
0
-
VDD
V
Tamb
ambient temperature
in free air
40
-
+125
C
t/V
input transition rise and fall
rate
VDD = 5 V
-
-
3.75
s/V
VDD = 10 V
-
-
0.5
s/V
VDD = 15 V
-
-
0.08
s/V
001aac285
15
VDD − VSS
(V)
10
operating area
5
0
0
Fig 8.
5
10
VDD − VEE (V)
15
Operating area as a function of the supply voltages
10. Static characteristics
Table 6.
Static characteristics
VSS = VEE = 0 V; VI = VSS or VDD unless otherwise specified.
Symbol Parameter
VIH
VIL
II
HIGH-level
input voltage
LOW-level
input voltage
input leakage
current
HEF4052B
Product data sheet
Tamb = 40 C Tamb = 25 C
Tamb = 85 C Tamb = 125 C Unit
Conditions
VDD
Min
Max
Min
Max
Min
Max
Min
Max
IO < 1 A
5V
3.5
-
3.5
-
3.5
-
3.5
-
V
10 V
7.0
-
7.0
-
7.0
-
7.0
-
V
15 V
11.0
-
11.0
-
11.0
-
11.0
-
V
IO < 1 A
5V
-
1.5
-
1.5
-
1.5
-
1.5
V
10 V
-
3.0
-
3.0
-
3.0
-
3.0
V
15 V
-
4.0
-
4.0
-
4.0
-
4.0
V
15 V
-
0.1
-
0.1
-
1.0
-
1.0
A
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 17 November 2011
© NXP B.V. 2011. All rights reserved.
7 of 22
HEF4052B
NXP Semiconductors
Dual 4-channel analog multiplexer/demultiplexer
Table 6.
Static characteristics …continued
VSS = VEE = 0 V; VI = VSS or VDD unless otherwise specified.
Symbol Parameter
IS(OFF)
OFF-state
leakage
current
Conditions
CI
Max
Min
Max
Min
Max
Min
Max
Z port;
15 V
all channels OFF;
see Figure 9
-
-
-
1000
-
-
-
-
nA
15 V
-
-
-
200
-
-
-
-
nA
5V
-
5
-
5
-
150
-
150
A
10 V
-
10
-
10
-
300
-
300
A
15 V
-
20
-
20
-
600
-
600
A
-
-
-
-
7.5
-
-
-
-
pF
supply current IO = 0 A
input
capacitance
Tamb = 85 C Tamb = 125 C Unit
Min
Y port;
per channel;
see Figure 10
IDD
Tamb = 40 C Tamb = 25 C
VDD
Sn, E inputs
10.1 Test circuits
VDD
S1 and S2
VDD or VSS
nYn
nZ
E
IS
VSS = VEE
VDD
VI
VO
001aak635
Fig 9.
Test circuit for measuring OFF-state leakage current Z port
VDD
VDD or VSS
S1 and S2
nY0
1
nZ
nYn
2
switch
IS
E
VSS = VEE
VSS
VO
VI
001aak636
Fig 10. Test circuit for measuring OFF-state leakage current nYn port
HEF4052B
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 17 November 2011
© NXP B.V. 2011. All rights reserved.
8 of 22
HEF4052B
NXP Semiconductors
Dual 4-channel analog multiplexer/demultiplexer
10.2 On resistance
Table 7.
ON resistance
Tamb = 25 C; ISW = 200 A; VSS = VEE = 0 V.
Symbol
Parameter
Conditions
VDD  VEE
Typ
Max
Unit
RON(peak)
ON resistance (peak)
VI = 0 V to VDD  VEE;
see Figure 11 and Figure 12
5V
350
2500

10 V
80
245

15 V
60
175

5V
115
340

10 V
50
160

15 V
40
115

5V
120
365

10 V
65
200

15 V
50
155

RON(rail)
ON resistance (rail)
VI = 0 V; see Figure 11 and Figure 12
VI = VDD  VEE;
see Figure 11 and Figure 12
RON
ON resistance mismatch
between channels
VI = 0 V to VDD  VEE; see Figure 11
5V
25
-

10 V
10
-

15 V
5
-

10.2.1 On resistance waveform and test circuit
V
VSW
VDD
VDD or VSS
S1 and S2
nYn
nZ
E
VSS = VEE
VSS
ISW
VI
001aak637
RON = VSW / ISW.
Fig 11. Test circuit for measuring RON
HEF4052B
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 17 November 2011
© NXP B.V. 2011. All rights reserved.
9 of 22
HEF4052B
NXP Semiconductors
Dual 4-channel analog multiplexer/demultiplexer
001aae648
400
RON
(Ω)
VDD = 5 V
300
200
10 V
100
15 V
0
0
5
10
15
VI (V)
Fig 12. Typical RON as a function of input voltage
11. Dynamic characteristics
Table 8.
Dynamic characteristics
Tamb = 25 C; VSS = VEE = 0 V; for test circuit see Figure 16.
Symbol
Parameter
tPHL
HIGH to LOW propagation delay nYn, nZ to nZ, nYn; see Figure 13
Conditions
Sn to nYn, nZ; see Figure 14
tPLH
LOW to HIGH propagation delay Yn, nZ to nZ, nYn; see Figure 13
Sn to nYn, nZ; see Figure 14
tPHZ
tPZH
tPLZ
HIGH to OFF-state
propagation delay
OFF-state to HIGH
propagation delay
LOW to OFF-state
propagation delay
HEF4052B
Product data sheet
E to nYn, nZ; see Figure 15
E to nYn, nZ; see Figure 15
E to nYn, nZ; see Figure 15
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 17 November 2011
VDD
Typ
Max
Unit
5V
10
20
ns
10 V
5
10
ns
15 V
5
10
ns
5V
150
305
ns
10 V
65
135
ns
15 V
50
100
ns
5V
10
20
ns
10 V
5
10
ns
15 V
5
10
ns
5V
150
300
ns
10 V
75
150
ns
15 V
50
100
ns
5V
95
190
ns
10 V
90
180
ns
15 V
85
180
ns
5V
130
260
ns
10 V
55
115
ns
15 V
45
85
ns
5V
100
205
ns
10 V
90
180
ns
15 V
90
180
ns
© NXP B.V. 2011. All rights reserved.
10 of 22
HEF4052B
NXP Semiconductors
Dual 4-channel analog multiplexer/demultiplexer
Table 8.
Dynamic characteristics …continued
Tamb = 25 C; VSS = VEE = 0 V; for test circuit see Figure 16.
Symbol
Parameter
Conditions
VDD
Typ
Max
Unit
tPZL
OFF-state to LOW
propagation delay
E to nYn, nZ; see Figure 15
5V
120
240
ns
10 V
50
100
ns
15 V
35
75
ns
11.1 Waveforms and test circuit
VDD
nYn or nZ
input
VM
VDD
Sn input
VEE
tPLH
tPLH
VO
nZ or nYn
output
VM
VSS
tPHL
tPHL
VO
90 %
nYn or nZ
output
VM
10 %
VEE
VEE
switch OFF
switch ON
001aac290
switch OFF
001aac291
Measurement points are given in Table 9.
Measurement points are given in Table 9.
Fig 13. nYn, nZ to nZ, nYn propagation delays
Fig 14. Sn to nYn, nZ propagation delays
VDD
E input
VM
VSS
tPLZ
nYn or nZ output
LOW-to-OFF
OFF-to-LOW
tPZL
VO
90 %
10 %
VEE
tPHZ
VO
tPZH
90 %
nYn or nZ output
HIGH-to-OFF
OFF-to-HIGH
10 %
VEE
switch ON
switch OFF
switch ON
001aac292
Measurement points are given in Table 9.
Fig 15. Enable and disable times
Table 9.
Measurement points
Supply voltage
Input
Output
VDD
VM
VM
5 V to 15 V
0.5VDD
0.5VDD
HEF4052B
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 17 November 2011
© NXP B.V. 2011. All rights reserved.
11 of 22
HEF4052B
NXP Semiconductors
Dual 4-channel analog multiplexer/demultiplexer
tW
VI
negative
pulse
0V
90 %
VM
10 %
tf
tr
tr
tf
VI
positive
pulse
0V
VM
10 %
90 %
VM
VM
tW
VDD
VDD VI
PULSE
GENERATOR
VI
VO
RL
S1
open
DUT
RT
CL
VSS
VEE
001aaj903
Test data is given in Table 10.
Definitions:
DUT = Device Under Test.
RT = Termination resistance should be equal to output impedance Zo of the pulse generator.
CL = Load capacitance including test jig and probe.
RL = Load resistance.
Fig 16. Test circuit for measuring switching times
Table 10.
Test data
Input
nYn, nZ
Load
Sn and E
tr, tf
VDD or VEE VDD or VSS  20 ns
[1]
S1 position
VM
CL
RL
tPHL[1]
0.5VDD
50 pF
10 k
VDD or VEE VEE
tPLH
tPZH, tPHZ tPZL, tPLZ other
VEE
VDD
VEE
For nYn to nZ propagation delays use VEE. For Sn to nYn or nZ propagation delays use VDD.
HEF4052B
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 17 November 2011
© NXP B.V. 2011. All rights reserved.
12 of 22
HEF4052B
NXP Semiconductors
Dual 4-channel analog multiplexer/demultiplexer
11.2 Additional dynamic parameters
Table 11. Additional dynamic characteristics
VSS = VEE = 0 V; Tamb = 25 C.
Symbol
THD
Parameter
Conditions
total harmonic distortion
3 dB frequency response
f(3dB)
VDD
Typ
Max
Unit
see Figure 17; RL = 10 k; CL = 15 pF; 5 V
channel ON; VI = 0.5VDD (p-p);
10 V
fi = 1 kHz
15 V
[1]
0.25
-
%
[1]
0.04
-
%
[1]
0.04
-
%
see Figure 18; RL = 1 k; CL = 5 pF;
channel ON; VI = 0.5VDD (p-p)
5V
[1]
13
-
MHz
10 V
[1]
40
-
MHz
70
-
50
15 V
[1]
iso
isolation (OFF-state)
see Figure 19; fi = 1 MHz; RL = 1 k;
CL = 5 pF; channel OFF;
VI = 0.5VDD (p-p)
10 V
[1]
Vct
crosstalk voltage
digital inputs to switch; see Figure 20;
RL = 10 k; CL = 15 pF;
E or Sn = VDD (square-wave)
10 V
Xtalk
crosstalk
between switches; see Figure 21;
fi = 1 MHz; RL = 1 k;
VI = 0.5VDD (p-p)
10 V
[1]
50
[1]
MHz
-
dB
-
mV
50
-
dB
fi is biased at 0.5 VDD; VI = 0.5VDD (p-p).
Table 12. Dynamic power dissipation PD
PD can be calculated from the formulas shown; VEE = VSS = 0 V; tr = tf  20 ns; Tamb = 25 C.
Symbol
PD
Parameter
dynamic power
dissipation
VDD
Typical formula for PD (W)
5V
where:
PD = 1300  fi + (fo  CL)  VDD
2
fi = input frequency in MHz;
10 V
PD = 6100  fi + (fo  CL)  VDD
2
fo = output frequency in MHz;
15 V
PD = 15600  fi + (fo  CL)  VDD2
CL = output load capacitance in pF;
VDD = supply voltage in V;
(CL  fo) = sum of the outputs.
11.2.1 Test circuits
VDD
VDD or VSS
VDD
S1 and S2
VDD or VSS
nYn
nZ
S1 and S2
E
VSS = VEE
VSS
RL
CL
D
RL
CL
dB
fi
001aak638
Fig 17. Test circuit for measuring total harmonic
distortion
Product data sheet
VSS = VEE
VSS
fi
HEF4052B
nYn
nZ
E
001aak639
Fig 18. Test circuit for measuring frequency response
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 17 November 2011
© NXP B.V. 2011. All rights reserved.
13 of 22
HEF4052B
NXP Semiconductors
Dual 4-channel analog multiplexer/demultiplexer
VDD
VDD or VSS
S1 and S2
nY0
1
nZ
nYn
2
switch
E
VSS = VEE
VSS
RL
CL
dB
fi
001aak657
Fig 19. Test circuit for measuring isolation (OFF-state)
0.5VDD
VDD
RL
S1 and S2
nY0
1
nZ
nYn
2
switch
E
G
VSS = VEE
VDD or VSS
RL
CL
V
VO
001aak658
a. Test circuit
logic
input (Sn, E)
off
on
off
Vct
VO
001aaj908
b. Input and output pulse definitions
Fig 20. Test circuit for measuring crosstalk voltage between digital inputs and switch
HEF4052B
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 17 November 2011
© NXP B.V. 2011. All rights reserved.
14 of 22
HEF4052B
NXP Semiconductors
Dual 4-channel analog multiplexer/demultiplexer
VDD
VDD
VDD or VSS
S1 and S2
nY0
nZ
nYn
VDD or VSS
S1 and S2
nY0
nZ
nYn
E
E
VSS = VEE
VSS
RL
VO
RL
VSS = VEE
VSS
VI
RL
VI
VO
001aak659
a. Switch closed condition
RL
001aak660
b. Switch open condition
Fig 21. Test circuit for measuring crosstalk between switches
HEF4052B
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 17 November 2011
© NXP B.V. 2011. All rights reserved.
15 of 22
HEF4052B
NXP Semiconductors
Dual 4-channel analog multiplexer/demultiplexer
12. Package outline
DIP16: plastic dual in-line package; 16 leads (300 mil)
SOT38-4
ME
seating plane
D
A2
A
A1
L
c
e
Z
w M
b1
(e 1)
b
b2
MH
9
16
pin 1 index
E
1
8
0
5
10 mm
scale
DIMENSIONS (inch dimensions are derived from the original mm dimensions)
UNIT
A
max.
A1
min.
A2
max.
b
b1
b2
c
D (1)
E (1)
e
e1
L
ME
MH
w
Z (1)
max.
mm
4.2
0.51
3.2
1.73
1.30
0.53
0.38
1.25
0.85
0.36
0.23
19.50
18.55
6.48
6.20
2.54
7.62
3.60
3.05
8.25
7.80
10.0
8.3
0.254
0.76
inches
0.17
0.02
0.13
0.068
0.051
0.021
0.015
0.049
0.033
0.014
0.009
0.77
0.73
0.26
0.24
0.1
0.3
0.14
0.12
0.32
0.31
0.39
0.33
0.01
0.03
Note
1. Plastic or metal protrusions of 0.25 mm (0.01 inch) maximum per side are not included.
OUTLINE
VERSION
REFERENCES
IEC
JEDEC
JEITA
EUROPEAN
PROJECTION
ISSUE DATE
95-01-14
03-02-13
SOT38-4
Fig 22. Package outline SOT38-4 (DIP16)
HEF4052B
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 17 November 2011
© NXP B.V. 2011. All rights reserved.
16 of 22
HEF4052B
NXP Semiconductors
Dual 4-channel analog multiplexer/demultiplexer
SO16: plastic small outline package; 16 leads; body width 3.9 mm
SOT109-1
D
E
A
X
c
y
HE
v M A
Z
16
9
Q
A2
A
(A 3)
A1
pin 1 index
θ
Lp
1
L
8
e
0
detail X
w M
bp
2.5
5 mm
scale
DIMENSIONS (inch dimensions are derived from the original mm dimensions)
UNIT
A
max.
A1
A2
A3
bp
c
D (1)
E (1)
e
HE
L
Lp
Q
v
w
y
Z (1)
mm
1.75
0.25
0.10
1.45
1.25
0.25
0.49
0.36
0.25
0.19
10.0
9.8
4.0
3.8
1.27
6.2
5.8
1.05
1.0
0.4
0.7
0.6
0.25
0.25
0.1
0.7
0.3
0.01
0.019 0.0100 0.39
0.014 0.0075 0.38
0.039
0.016
0.028
0.020
inches
0.010 0.057
0.069
0.004 0.049
0.16
0.15
0.05
0.244
0.041
0.228
0.01
0.01
0.028
0.004
0.012
θ
8o
o
0
Note
1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included.
REFERENCES
OUTLINE
VERSION
IEC
JEDEC
SOT109-1
076E07
MS-012
JEITA
EUROPEAN
PROJECTION
ISSUE DATE
99-12-27
03-02-19
Fig 23. Package outline SOT109-1 (SO16)
HEF4052B
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 17 November 2011
© NXP B.V. 2011. All rights reserved.
17 of 22
HEF4052B
NXP Semiconductors
Dual 4-channel analog multiplexer/demultiplexer
TSSOP16: plastic thin shrink small outline package; 16 leads; body width 4.4 mm
SOT403-1
E
D
A
X
c
y
HE
v M A
Z
9
16
Q
(A 3)
A2
A
A1
pin 1 index
θ
Lp
L
1
8
e
detail X
w M
bp
0
2.5
5 mm
scale
DIMENSIONS (mm are the original dimensions)
UNIT
A
max.
A1
A2
A3
bp
c
D (1)
E (2)
e
HE
L
Lp
Q
v
w
y
Z (1)
θ
mm
1.1
0.15
0.05
0.95
0.80
0.25
0.30
0.19
0.2
0.1
5.1
4.9
4.5
4.3
0.65
6.6
6.2
1
0.75
0.50
0.4
0.3
0.2
0.13
0.1
0.40
0.06
8o
o
0
Notes
1. Plastic or metal protrusions of 0.15 mm maximum per side are not included.
2. Plastic interlead protrusions of 0.25 mm maximum per side are not included.
OUTLINE
VERSION
SOT403-1
REFERENCES
IEC
JEDEC
JEITA
MO-153
EUROPEAN
PROJECTION
ISSUE DATE
99-12-27
03-02-18
Fig 24. Package outline SOT403-1 (TSSOP16)
HEF4052B
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 17 November 2011
© NXP B.V. 2011. All rights reserved.
18 of 22
HEF4052B
NXP Semiconductors
Dual 4-channel analog multiplexer/demultiplexer
13. Revision history
Table 13.
Revision history
Document ID
Release date
Data sheet status
Change notice
Supersedes
HEF4052B v.8
20111117
Product data sheet
-
HEF4052B v.7
Modifications:
•
•
Legal pages updated.
Changes in “General description”, “Features and benefits” and “Applications”.
HEF4052B v.7
20100326
Product data sheet
-
HEF4052B v.6
HEF4052B v.6
20100308
Product data sheet
-
HEF4052B v.5
HEF4052B v.5
20091127
Product data sheet
-
HEF4052B v.4
HEF4052B v.4
20090924
Product data sheet
-
HEF4052B_CNV v.3
HEF4052B_CNV v.3
19950101
Product specification
-
HEF4052B_CNV v.2
HEF4052B_CNV v.2
19950101
Product specification
-
-
HEF4052B
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 17 November 2011
© NXP B.V. 2011. All rights reserved.
19 of 22
HEF4052B
NXP Semiconductors
Dual 4-channel analog multiplexer/demultiplexer
14. Legal information
14.1 Data sheet status
Document status[1][2]
Product status[3]
Definition
Objective [short] data sheet
Development
This document contains data from the objective specification for product development.
Preliminary [short] data sheet
Qualification
This document contains data from the preliminary specification.
Product [short] data sheet
Production
This document contains the product specification.
[1]
Please consult the most recently issued document before initiating or completing a design.
[2]
The term ‘short data sheet’ is explained in section “Definitions”.
[3]
The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nxp.com.
14.2 Definitions
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. NXP Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences of
use of such information.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is intended
for quick reference only and should not be relied upon to contain detailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local NXP Semiconductors sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
Product specification — The information and data provided in a Product
data sheet shall define the specification of the product as agreed between
NXP Semiconductors and its customer, unless NXP Semiconductors and
customer have explicitly agreed otherwise in writing. In no event however,
shall an agreement be valid in which the NXP Semiconductors product is
deemed to offer functions and qualities beyond those described in the
Product data sheet.
14.3 Disclaimers
Limited warranty and liability — Information in this document is believed to
be accurate and reliable. However, NXP Semiconductors does not give any
representations or warranties, expressed or implied, as to the accuracy or
completeness of such information and shall have no liability for the
consequences of use of such information.
In no event shall NXP Semiconductors be liable for any indirect, incidental,
punitive, special or consequential damages (including - without limitation - lost
profits, lost savings, business interruption, costs related to the removal or
replacement of any products or rework charges) whether or not such
damages are based on tort (including negligence), warranty, breach of
contract or any other legal theory.
Notwithstanding any damages that customer might incur for any reason
whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards
customer for the products described herein shall be limited in accordance
with the Terms and conditions of commercial sale of NXP Semiconductors.
malfunction of an NXP Semiconductors product can reasonably be expected
to result in personal injury, death or severe property or environmental
damage. NXP Semiconductors accepts no liability for inclusion and/or use of
NXP Semiconductors products in such equipment or applications and
therefore such inclusion and/or use is at the customer’s own risk.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. NXP Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Customers are responsible for the design and operation of their applications
and products using NXP Semiconductors products, and NXP Semiconductors
accepts no liability for any assistance with applications or customer product
design. It is customer’s sole responsibility to determine whether the NXP
Semiconductors product is suitable and fit for the customer’s applications and
products planned, as well as for the planned application and use of
customer’s third party customer(s). Customers should provide appropriate
design and operating safeguards to minimize the risks associated with their
applications and products.
NXP Semiconductors does not accept any liability related to any default,
damage, costs or problem which is based on any weakness or default in the
customer’s applications or products, or the application or use by customer’s
third party customer(s). Customer is responsible for doing all necessary
testing for the customer’s applications and products using NXP
Semiconductors products in order to avoid a default of the applications and
the products or of the application or use by customer’s third party
customer(s). NXP does not accept any liability in this respect.
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) will cause permanent
damage to the device. Limiting values are stress ratings only and (proper)
operation of the device at these or any other conditions above those given in
the Recommended operating conditions section (if present) or the
Characteristics sections of this document is not warranted. Constant or
repeated exposure to limiting values will permanently and irreversibly affect
the quality and reliability of the device.
Terms and conditions of commercial sale — NXP Semiconductors
products are sold subject to the general terms and conditions of commercial
sale, as published at http://www.nxp.com/profile/terms, unless otherwise
agreed in a valid written individual agreement. In case an individual
agreement is concluded only the terms and conditions of the respective
agreement shall apply. NXP Semiconductors hereby expressly objects to
applying the customer’s general terms and conditions with regard to the
purchase of NXP Semiconductors products by customer.
Right to make changes — NXP Semiconductors reserves the right to make
changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.
No offer to sell or license — Nothing in this document may be interpreted or
construed as an offer to sell products that is open for acceptance or the grant,
conveyance or implication of any license under any copyrights, patents or
other industrial or intellectual property rights.
Suitability for use — NXP Semiconductors products are not designed,
authorized or warranted to be suitable for use in life support, life-critical or
safety-critical systems or equipment, nor in applications where failure or
Export control — This document as well as the item(s) described herein
may be subject to export control regulations. Export might require a prior
authorization from competent authorities.
HEF4052B
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 17 November 2011
© NXP B.V. 2011. All rights reserved.
20 of 22
HEF4052B
NXP Semiconductors
Dual 4-channel analog multiplexer/demultiplexer
Non-automotive qualified products — Unless this data sheet expressly
states that this specific NXP Semiconductors product is automotive qualified,
the product is not suitable for automotive use. It is neither qualified nor tested
in accordance with automotive testing or application requirements. NXP
Semiconductors accepts no liability for inclusion and/or use of
non-automotive qualified products in automotive equipment or applications.
NXP Semiconductors’ specifications such use shall be solely at customer’s
own risk, and (c) customer fully indemnifies NXP Semiconductors for any
liability, damages or failed product claims resulting from customer design and
use of the product for automotive applications beyond NXP Semiconductors’
standard warranty and NXP Semiconductors’ product specifications.
In the event that customer uses the product for design-in and use in
automotive applications to automotive specifications and standards, customer
(a) shall use the product without NXP Semiconductors’ warranty of the
product for such automotive applications, use and specifications, and (b)
whenever customer uses the product for automotive applications beyond
14.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks
are the property of their respective owners.
15. Contact information
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: [email protected]
HEF4052B
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 17 November 2011
© NXP B.V. 2011. All rights reserved.
21 of 22
HEF4052B
NXP Semiconductors
Dual 4-channel analog multiplexer/demultiplexer
16. Contents
1
2
3
4
5
6
6.1
6.2
7
7.1
8
9
10
10.1
10.2
10.2.1
11
11.1
11.2
11.2.1
12
13
14
14.1
14.2
14.3
14.4
15
16
General description . . . . . . . . . . . . . . . . . . . . . . 1
Features and benefits . . . . . . . . . . . . . . . . . . . . 1
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Ordering information . . . . . . . . . . . . . . . . . . . . . 2
Functional diagram . . . . . . . . . . . . . . . . . . . . . . 2
Pinning information . . . . . . . . . . . . . . . . . . . . . . 5
Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 5
Functional description . . . . . . . . . . . . . . . . . . . 6
Function table . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 6
Recommended operating conditions. . . . . . . . 7
Static characteristics. . . . . . . . . . . . . . . . . . . . . 7
Test circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
On resistance . . . . . . . . . . . . . . . . . . . . . . . . . . 9
On resistance waveform and test circuit. . . . . . 9
Dynamic characteristics . . . . . . . . . . . . . . . . . 10
Waveforms and test circuit . . . . . . . . . . . . . . . 11
Additional dynamic parameters . . . . . . . . . . . 13
Test circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Package outline . . . . . . . . . . . . . . . . . . . . . . . . 16
Revision history . . . . . . . . . . . . . . . . . . . . . . . . 19
Legal information. . . . . . . . . . . . . . . . . . . . . . . 20
Data sheet status . . . . . . . . . . . . . . . . . . . . . . 20
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Contact information. . . . . . . . . . . . . . . . . . . . . 21
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section ‘Legal information’.
© NXP B.V. 2011.
All rights reserved.
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: [email protected]
Date of release: 17 November 2011
Document identifier: HEF4052B
Similar pages