SPECIFICATION FOR APPROVAL PAGE: 1 REF : PROD. NAME WOUND CHIP INDUCTOR CC2520□□□□3□-□□□ ABC'S DWG NO. ABC'S ITEM NO. Ⅰ﹒CONFIGURATION & DIMENSIONS： B A : 2.5±0.2 m/m B : 2.0±0.1 m/m C : 1.8±0.1 m/m E : 1.4±0.1 m/m F : 0.40 m/m C 0.50 1.5 Not Marking A 0.9 F F 1.5 0.9 （ PCB Pattern ） E Ⅱ﹒SCHEMATIC DIAGRAM： d a Ⅲ﹒MATERIALS： a﹒Core：Ferrite DR core c b﹒Wire ：Enamelled copper wire c﹒Terminal：Cu/Sn b d﹒Encapsulate：Epoxy novolac molding compound e﹒Remark：Products comply with RoHS' requirements Peak Temp：245℃ max. Max time above 225℃ ：30sec max. Max time above 200℃ ：50sec max. Ⅳ﹒GENERAL SPECIFICATION： a﹒Temp. rise ：20℃ max. b﹒Ambient temp.：80℃ max. c﹒Storage temp.：-40℃ ----+100℃ inductance drop within 10% g﹒Resistance to solder heat：260℃.10 secs. h﹒Resistance to solvent：Per MIL-STD-202F AR-001A Temperature ( ℃ ) f﹒Rated current：Current cause Preheat Area Reflow Area Forced Cooling Area 2 ~ 4℃ / sec 150 ~ 180℃ / 90 ~ 150sec 2 ~ 4℃ / sec 3 ~ 5℃ / sec 240±5℃ 250 d﹒Operating temp.：-40℃----+85℃ e﹒Terminal strength：0.5 kg min. Temperature Rising Area 10sec 200 30sec max. ( 20~30sec ) 150 100 50 0 50 100 150 Time ( seconds ) 200 250 SPECIFICATION FOR APPROVAL REF : PAGE: 2 PROD. ABC'S DWG NO. WOUND CHIP INDUCTOR NAME CC2520□□□□3□-□□□ ABC'S ITEM NO. Ⅴ﹒ELECTRICAL CHARACTERISTICS： 7.96 SRF ( MHz ) min. 200 RDC (Ω) ±30％ 0.34 IDC ( mA ) max. 475 20 7.96 165 0.42 435 2.2±20% 20 7.96 95 0.50 390 CC25203R3M3□-□□□ 3.3±20% 20 7.96 55 0.65 340 CC25204R7M3□-□□□ 4.7±20% 20 7.96 43 0.80 285 CC25206R8M3□-□□□ 6.8±20% 20 7.96 39 1.00 275 CC2520100K3□-□□□ 10.0±10% 30 2.52 32 1.69 210 CC2520150K3□-□□□ 15.0±10% 30 2.52 21 2.20 175 CC2520220K3□-□□□ 22.0±10% 30 2.52 18 2.80 160 CC2520330K3□-□□□ 33.0±10% 30 2.52 16 4.20 120 DWG No. Inductance ( µH ) Q typ. Test Freq ( MHz ) CC25201R0M3□-□□□ 1.0±20% 20 CC25201R5M3□-□□□ 1.5±20% CC25202R2M3□-□□□ 1)．□ : Packaging information… A : Bulk 2)．"- AR-001A □□□ ":Reference code B : Taping Reel SPECIFICATION FOR APPROVAL PAGE: 3 REF : PROD. NAME ABC'S DWG NO. WOUND CHIP INDUCTOR CC2520□□□□3□-□□□ ABC'S ITEM NO. Ⅵ﹒PACKAGING INFORMATION： ( 1 ) Configuration T Cover Tape N A B 2.0±0.5 ∮C ∮C D G Embossed Carrier ※ Carrier Tape Width : D P:4 m/m End 4 m/m Leader no component 200 m/m min. Start Trailer no component 400 m/m min. Components User direction of feed ( 2 ) Dimensions Unit:m/m Style A 07 - 08 178 B 21±0.8 C D G N T 13 8 10 +0 50 -0 12.5 ( 3 ) Q'TY & G.W. Per package Inner : Reel Series CC2520 AR-001A Q'TY (pcs) 2,000 G.W. (gw) 60 Outer : Carton Style Q'TY (pcs) 07 - 08 100,000 G.W. (Kg) 5.0 Size (cm) 41 x 39 x 22 SPECIFICATION FOR APPROVAL REF : PAGE: 4 PROD. WOUND CHIP INDUCTOR NAME ABC'S DWG NO. CC2520□□□□3□-□□□ ABC'S ITEM NO. Ⅶ﹒DWGING NUMBER EXPRESSION： C C 2 5 2 0 Reference code Appendix code 2 : Package Appendix code 1 : Classification Tolerance code Electrical code Dimension code Type code Appendix code 1：Product Classification L：Lead Free Standard products comply with RoHS' requirements 1 ~ 9：Lead Free Special products comply with RoHS' requirements Appendix code 2：Package Information Code AR-001A Inner package Inner package Q'TY A T.B.D. T.B.D. B T / R ( Reel package ) 2000 pcs Remark SPECIFICATION FOR APPROVAL PAGE: 5 REF : PROD. NAME WOUND CHIP INDUCTOR ABC'S DWG NO. CC2520□□□□3□-□□□ ABC'S ITEM NO. Ⅷ﹒RELIABILITY TEST： Test item Specification Test condition / Test method Electrical performance test Inductance L Q Self resonance frequency SRF DC Resistance RDC □HP4194A with HP-16034E test fixture Refer to standard electrical characteristic list □HP4291A with HP-16093A test fixture CH-502AC Applied the current to coils，The Rated current IDC Inductance change shall be less than 10% to initial value & temperature rise shall not be more than 20℃ 1﹒Applied the allowed DC current for 10 minutes 2﹒Temperature measure by digital surface thermometer Temperature rise test 20℃ max. Over load test After test，Inductors shall be no evidence of electrical and mechanical damage Applied 2 times of rated allowed DC current to inductor for a period of 5 minutes Withstanding voltage test After tset，Inductors shall be no evidence of electrical and mechanical damage AC voltage of 1000VAC applied between inductors terminal and coating for 5 seconds Insulation resistance test 1000 MΩ min﹒ 100 VDC applied between inductor terminal and coating Mechanical performance test Vibration test ( Low frequency ) 1﹒Inductors shall be no evidence of electrical and mechanical damage 1﹒Amplitude：1.5 m/m 2﹒Frequency：10 -- 55 -- 10 Hz / 1min. 3﹒Direction：X，Y，Z 4﹒Duration：2 hrs / X，Y，Z Shock test 2﹒Inductance shall not change more than±5% Inductors shall be dropped 10 times from a height of 1m onto 3cm wooden board Resistance to soldering heat 3﹒Q Shall not change more than ±20% Temp：260±5℃ Time：10±1.0 sec. AR-001A SPECIFICATION FOR APPROVAL REF : PAGE: 6 PROD. NAME WOUND CHIP INDUCTOR ABC'S DWG NO. CC2520□□□□3□-□□□ ABC'S ITEM NO. Terminal strength-pull test Terminal shall not be loosened or ruptured A 0.5kg load shall be applied to both Terminals in the axis direction for 1 minute﹒ Solderability test The terminal shall be at least 90% covered with solder After fluxing，Inductor shall be dipped in a melted solder bath at 230±5℃ for 5 seconds﹒ Resistance to solvent test There shall be no case deformation change in appearance or obliteration of marking MIL-STD-202F，Method 215D Climatic test Temperature characteristic Humidity test Cold test 1﹒Inductors shall be no evidence of electrical and mechanical damage 2﹒Inductance shall not change more than ±10% 3﹒Q shall not change more than ±20% Thermal shock test Dry heat test High temperature load life test Humidity load life There shall be no evidence of short or open circuiting -25℃ -- 85℃ 1﹒Temp：40±2℃ 2﹒R.H.：90 -- 95% 3﹒Time：96±2 hours 1﹒Temp：-25±2℃ 2﹒Time：96±2 hours Room temp 15 mins Room temp 15 mins Total：5 cycles 1﹒Temp：85±2℃ 2﹒Time：96±2 hours 1﹒Temp：85±2℃ 2﹒Time：1000±12 hours 3﹒Load：Allowed DC current 1﹒Temp：40±2℃ 2﹒R.H.：90 -- 95% 3﹒Time：1000±12 hours 4﹒Load：Allowed DC current Note： Unless otherwise specified , Allow the specimen to stand at room temperature for 1 hour or more but not more than 2 hours , Measure the electrical and mechanical performances AR-001A -25±2℃ 30 mins 85±2℃ 30 mins SPECIFICATION FOR APPROVAL PAGE: 7 REF : PROD. NAME WOUND CHIP INDUCTOR ABC'S DWG NO. CC2520□□□□3□-□□□ ABC'S ITEM NO. Ⅸ﹒UL CARD： OBMW2 Magnet Wire-Component September 8, 2000 JUNG SHING WIRE CO LTD 231 CHUNG CHENG RD, SEC 3 JEN-TEH HSIANG, TAINAN HSIEN TAIWAN Mtl Dsg AIW CFUEWB EIAIW EILOCKY EILOCKW EIW EIW-2 FL.EILOCKY LSFFW LSUEW PEW PEY SF.FLW SF.EIW SF.BY@ SF.FLY@ SF.BLOCKBS SF.EILOCKY# SF.EILOCKBS SF.BW@ SFFW Mark Dsg ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ BC Polyamideimide Polyurethane Polyesterimide Polyesterimide Polyesterimide Polyesterimide Polyesterimide Modified Polyester Polyurethane Polyurethane Polyester Polyester Modified Polyester Polyesterimide Modified Polyester Modified Polyester Modified Polyester Polyesterimide Polyesterimide Modified Polyester Polyurethane SFFY UEW-1 UEW-2 UEW-4 UEY UEY-2 OC ____ ____ Polyamideimide Polyamide Modified Epoxy ____ ____ Polyamide ____ ____ ____ ____Nylon ____ Nylon Nylon Modified Polyamide Polyamide Modified Polyamide ____ ANSI Type MW81-C MW75C MW35C ___ ___ ___ MW74-C ___ MW79-C ___ ___ MW24-C MW26C MW77C MW27-C MW27-C ___ ___ ___ Mark Dsg ____ ____ ____ ____ ____ ____ BC Coat Typ 220 130 200 180 200 220 200 155 155 130 155 155 155 180 155 155 155 MW26C MW79 155 155 A not-for-profit organization dedicated to public safety and committed to quality service OC Polyamide ____ ____ ____ Polyurethane Polyurethane Polyurethane Polyurethane Polyurethane Polyurethane Temp Class 180 180 Page 1 of 2 287806002 Mtl Dsg Coat Typ E174837 Nylon Polyamide ANSI Type MW80C MW2-C ___ MW75C MW28-C MW28-C Temp Class 155 105 130 130 130 130 @-May be suffixed by LZ; # - May be suffixed by LZ, EL or LZI. LZ - Signifies magned wires twisted together; EL - signifies base coated magnet wire laid parallel with top coat applied overall; LZL - signifies base coated magnet wire twisted together and covered with top coat overall. Marking: Company name or trademarks or 榮星電線 , material designation or marked designation on packaed or reel, and Recognized Component Mark. See General Information Preceding These Recognitions For use only in equipment where the acceptability of the combination is determined by Underwriters Laboratories Inc. 287806002 AR-001A Page 2 of 2 OBMW2⁄E174837 September 8 , 2000 SPECIFICATION FOR APPROVAL PAGE: 8 REF : PROD. NAME WOUND CHIP INDUCTOR ABC'S DWG NO. CC2520□□□□3□-□□□ ABC'S ITEM NO. March 4, 1994 OMFZ2 E59481 (S) BM-21 BM-22 BM-23 EME-1100 EME-1200 EME-5961C ALL ALL ALL 0.79 0.79 0.79 94HB 94HB 94V-0 50 50 50 50 50 50 50 50 50 BK BK BK BK BK BK 0.84 6.4 0.84 6.4 0.3 3.1 94V-0 94V-0 94V-0 94V-0 94V-0 94V-0 130 130 130 130 130 130 130 130 130 130 130 130 130 130 130 130 130 130 __________________ Reports: January 19, 1988: January 19, 1988: January 19, 1988: June 2, 1988; June 2, 1998; June 2, 1988. R AR-001A