Volgen MT10A-1233SI The mt10a and mt10a-w sery Datasheet

FEATURES
• 10 WATTS OUTPUT POWER
• OUTPUT CURRENT UP TO 2.5A
• STANDARD 2.0 X 1.0 X 0.4 INCH PACKAGE
• HIGH EFFICIENCY UP TO 87%
• 2:1 AND 4:1 WIDE INPUT VOLTAGE RANGE
• SIX-SIDED CONTINUOUS SHIELD
• FIXED SWITCHING FREQUENCY (300KHz)
• ISO9001 CERTIFIED MANUFACTURING FACILITIES
• COMPLIANT TO RoHS EU DIRECTIVE 2002/95/EC
DESCRIPTION
The MT10A and MT10A-W series offer 10 watts of output power from a
2.0 x 1.0 x 0.4 inch package. MT10A series have 2:1 wide input voltage of
9-18, 18-36 and 36-75VDC. MT10A-W series have 4:1 ultra wide input
voltage of 9-36 and 18-75VDC.
T E C H N I C A L S P E C I F I C AT I O N
All specifications are typical at nominal input, full load and 25ºC otherwise noted.
OUTPUT SPECIFICATIONS
INPUT SPECIFICATIONS
Output power
Voltage accuracy
Full load and nominal Vin
± 1%
Minimum load
LL to HL at Full Load
± 0.2%
± 0.5%
± 1%
± 5%
Single
Dual
Cross regulation(Dual) Asymmetrical load 25% / 100% FL
Single
Ripple and noise
20MHz bandwidth
See table
Dual
±0.02% / ºC, max.
Temperature coefficient
Load regulation
No Load
to Full Load
Transient response recovery time 25% load step change
3.3V output
Over voltage protection 5V output
Zener diode clamp
12V output
15V output
Over load protection
% of FL at nominal input
Short circuit protection
250µS
3.9VDC
6.2VDC
15VDC
18VDC
150%, max.
Hiccup, automatics recovery
Input surge voltage
100mS max
Input reflected ripple current
12V input
24V input
48V input
Nominal Vin and full load
36VDC
50VDC
100VDC
30mAp-p
Nominal Vin and
Power up
20mS, typ.
constant resistive load
Remote ON/OFF (Option) (Note 6)
(Positive logic)
DC-DC ON
Open or 3.5V < Vr < 12V
DC-DC OFF
Short or 0V < Vr < 1.2V
(Negative logic)
DC-DC ON
Short or 0V < Vr < 1.2V
DC-DC OFF
Open or 3.5V < Vr < 12V
Input current of remote control pin Nominal Vin
-0.5mA ~ +1mA
Remote off state input current
Nominal Vin
20mA
Start up time
Standard
-25ºC ~ +85ºC (with derating)
M1 (Note 7)
-40ºC ~ +85ºC (non-derating)
M2 (W series) -40ºC ~ +85ºC (with derating)
+100ºC
300pF, max.
Storage temperature range
300KHz, typ.
Thermal impedance (Note 8)
-55ºC ~ +105ºC
Nature convection
12ºC/watt
Nature convection with heat-sink 10ºC/watt
MIL-STD-810F
See table
Isolation voltage
1600VDC, min.
Isolation resistance
10 ohms, min.
9
Isolation capacitance
Switching frequency
Case material
Nickel-coated copper
Base material
Non-conductive black plastic
MTBF (Note 1)
Input filter
Operating ambient
temperature
(Reference derating curve)
Maximum case temperature
Efficiency
Weight
MT10A-W
9 – 18VDC
18 – 36VDC
36 – 75VDC
9 – 36VDC
18 – 75VDC
Pi type
ENVIRONMENTAL SPECIFICATIONS
GENERAL SPECIFICATIONS
Dimensions
12V nominal input
24V nominal input
48V nominal input
24V nominal input
48V nominal input
Input voltage range
0%
Line regulation
Potting material
MT10A
10 Watts, max.
Epoxy (UL94-V0)
2.00 X 1.00 X 0.40 Inch
(50.8 X 25.4 X 10.2 mm)
27g (0.95oz)
6
BELLCORE TR-NWT-000332 1.976 x 10 hrs
6
1.416 x 10 hrs
MIL-HDBK-217F
Kaga Electronics (USA) Inc.
Thermal shock
Vibration
MIL-STD-810F
Relative humidity
5% to 95% RH
EMC CHARACTERISTICS
EMI (Note 9)
EN55022
ESD
Air
EN61000-4-2
Contact
Radiated immunity
Fast transient (Note 10)
Surge (Note 10)
Conducted immunity
EN61000-4-3
EN61000-4-4
EN61000-4-5
EN61000-4-6
http://www.volgen.com
Class A
± 8KV
± 6KV
10 V/m
± 2KV
± 1KV
10 Vr.m.s
Tel: (408)570-0955
Perf. Criteria B
Perf. Criteria A
Perf. Criteria B
Perf. Criteria B
Perf. Criteria A
Model
Number
Input
Range
MT10A-1233SI
MT10A-1205SI
MT10A-1212SI
MT10A-1215SI
MT10A-1205WI
MT10A-1212WI
MT10A-1215WI
MT10A-2433SI (W)
MT10A-2405SI (W)
MT10A-2412SI (W)
MT10A-2415SI (W)
MT10A-2405WI (W)
MT10A-2412WI (W)
MT10A-2415WI (W)
MT10A-4833SI (W)
MT10A-4805SI (W)
MT10A-4812SI (W)
MT10A-4815SI (W)
MT10A-4805WI (W)
MT10A-4812WI (W)
MT10A-4815WI (W)
9 – 18 VDC
9 – 18 VDC
9 – 18 VDC
9 – 18 VDC
9 – 18 VDC
9 – 18 VDC
9 – 18 VDC
18 – 36 (9 – 36) VDC
18 – 36 (9 – 36) VDC
18 – 36 (9 – 36) VDC
18 – 36 (9 – 36) VDC
18 – 36 (9 – 36) VDC
18 – 36 (9 – 36) VDC
18 – 36 (9 – 36) VDC
36 – 75(18 – 75) VDC
36 – 75 (18 – 75) VDC
36 – 75 (18 – 75) VDC
36 – 75 (18 – 75) VDC
36 – 75 (18 – 75) VDC
36 – 75 (18 – 75) VDC
36 – 75 (18 – 75) VDC
Output Current
Output
Min.
Voltage
Full load
load
3.3 VDC
5 VDC
12 VDC
15 VDC
± 5 VDC
± 12 VDC
± 15 VDC
3.3 VDC
5 VDC
12 VDC
15 VDC
± 5 VDC
± 12 VDC
± 15 VDC
3.3 VDC
5 VDC
12 VDC
15 VDC
± 5 VDC
± 12 VDC
± 15 VDC
0mA
0mA
0mA
0mA
0mA
0mA
0mA
0mA
0mA
0mA
0mA
0mA
0mA
0mA
0mA
0mA
0mA
0mA
0mA
0mA
0mA
2000mA
2000mA
830mA
670mA
± 1000mA
± 416mA
± 333mA
2000(2500mA)
2000mA
830mA
670mA
± 1000mA
± 416mA
± 333mA
2000(2500mA)
2000mA
830mA
670mA
± 1000mA
± 416mA
± 333mA
Input Current
Output (4)
No load Full load
Ripple & Noise
(3)
(2)
50mVp-p
50mVp-p
50mVp-p
50mVp-p
75mVp-p
75mVp-p
75mVp-p
50mVp-p
50mVp-p
50mVp-p
50mVp-p
75mVp-p
75mVp-p
75mVp-p
50mVp-p
50mVp-p
50mVp-p
50mVp-p
75mVp-p
75mVp-p
75mVp-p
17mA
21mA
38mA
36mA
39mA
47mA
45mA
15(13mA)
22(11mA)
18(16mA)
36(26mA)
28(15mA)
24(15mA)
31(22mA)
11(10mA)
14(9mA)
14(9mA)
10(11mA)
16(12mA)
19(20mA)
16(20mA)
724mA
1082mA
1037mA
1046mA
1042mA
1053mA
1041mA
362(465mA)
534 (548mA)
519 (519mA)
523 (544mA)
527 (534mA)
513 (547mA)
520 (548mA)
181(239mA)
260 (270mA)
253 (259mA)
252 (262mA)
260 (267mA)
254 (281mA)
256 (270mA)
Eff (4) Capacitor(5)
(%)
Load max
80
81
84
84
84
83
84
80(78)
82 (80)
84 (84)
84 (81)
83 (82)
85 (80)
84 (80)
80(76)
84 (81)
86 (84)
87 (84)
84 (82)
86 (78)
85 (81)
6800µF
4700µF
690µF
470µF
± 680µF
± 330µF
± 110µF
6800µF
4700µF
690µF
470µF
± 680µF
± 330µF
± 110µF
6800µF
4700µF
690µF
470µF
± 680µF
± 330µF
± 110µF
Note
1.
BELLCORE TR-NWT-000332. Case 1: 50% Stress, Temperature at 40ºC.
MIL-HDBK-217F Notice2 @Ta=25 ºC, Full load (Ground, Benign, controlled environment).
2. Maximum value at nominal input voltage and full load of standard type.
3. Typical value at nominal input voltage and no load.
4. Typical value at nominal input voltage and full load.
5. Test by minimum Vin and constant resistive load.
6. The ON/OFF control pin voltage is referenced to -Vin.
To order positive logic ON/OFF control add the suffix-P (Ex:MT10A-1205SI-P); To order negative logic ON-OFF control add the suffix-N (Ex: MT10A-1205SI-N)
7. M1 version is more efficient; therefore, it can be operated in a more extensive temperature range than standard and M2 version.
8. Heat sink is optional and P/N: 7G-0020C-F.
9. The MT10A series can meet EN55022 Class A with parallel an external capacitor to the input pins.
Recommend: 12Vin : 4.7µF/25V 1210 MLCC .
24Vin : 2.2µF/50V 1812 MLCC .
48Vin : 1.5µF/100V 1812 MLCC .
10. An external input filter capacitor is required if the module has to meet EN61000-4-4, EN61000-4-5. The filter capacitor Kaga USA suggests: Nippon chemi-con
KY series, 220μF/100V, ESR 48mΩ.
1.00(25.4)
0.50
(12.7)
DIA. 0.04(1.0)
0.400 0.400
(10.16) (10.16)
3
4
5
Bottom
View
1 2
6
0.800(20.32)
DUAL
+ INPUT
- INPUT
+ OUTPUT
COMMON
- OUTPUT
CTRL (Option)
0.60(15.2)
SINGLE
+ INPUT
- INPUT
+ OUTPUT
NO PIN
- OUTPUT
CTRL (Option)
2.00(50.8)
PIN CONNECTION
PIN
1
2
3
4
5
6
0.40
(10.2)
0.100(2.54)
0.200(5.08)
1. All dimensions in Inches (mm)
Tolerance: X.XX±0.02 (X.X±0.5)
X.XXX±0.01 (X.XX±0.25)
2. Pin pitch tolerance ±0.01(0.25)
3. Pin dimension tolerance ±0.004 (0.1)
Kaga Electronics (USA) Inc.
http://www.volgen.com
Tel: (408)570-0955
0.22(5.6)
Similar pages