POWER DS800SL Series 800 Watts Bulk Front End Data Sheet Total Output Power: 800 Watts +5.0 Vdc Standby SPECIAL FEATURES 800 W output power 19.05 W/cu-in 1U X 54.5 mm form factor (slimline) N + 1 redundant Hot-swap Internal OR’ing 5.0 V housekeeping High efficiency 92% @ 200 Vac, 50% load (Climate Savers Gold) Variable speed “smart fans” EMI Class B Available in two airflow directions SAFETY UL/cUL 60950 -1 CSA 60950-1 VDE 60950-1 China CCC CB Scheme Report/Cert Electrical Specifications Input Input range (operating) 90 - 264 Vac Input range (nominal) 115 / 230 Vac Frequency 47 - 63 Hz Input fusing Internal 10 A fuse Inrush current ≤ 40 A peak Either hot or cold start Power factor 0.99 typical Meets EN61000-3-2 Harmonics Meets IEC 1000-3-2 requirements Input current 10.0 A RMS max input current At 100 Vac Holdup time 10 ms minimum for main O/P At full rated load Undervoltage lockout 85 ± 3.0 Vac 80 ± 3.0 Vac Turn-on voltage Turn-off voltage Overvoltage lockout N/A Leakage current < 1.0 mA On/Off power switch N/A Power line transient MOV directly after the fuse At 264 Vac DS800SL Series Data Sheet Efficiency Curve 800 W DS Slim DS800SL-3-001 Power Derating 92.0% 88.0% 230 Vac, 50 Hz 86.0% 115 Vac, 60 Hz 84.0% Power Rating Efficiency 90.0% 82.0% 80.0% 0.0 820 800 780 760 740 720 700 680 660 640 620 100Vac 110Vac 230Vac 0 100.0 200.0 300.0 400.0 500.0 600.0 700.0 800.0 900.0 10 20 30 40 50 Ambient Temperature (degC) Output Power [W] Output Output rating 12 V @ 66.7 A; 800 W 5.0 Vsb @ 4 A; 20 W 90 - 264 Vac Setpoint 12.0 V Total regulation range 12 V ± 1% 5.0 Vsb ± 3% Line/load/transient when measured at output connector Rated load 800 W maximum No derating over operating temp range for forward air Minimum load 12 V @ 0.5 A 5.0 Vsb @ 0.0 A No load operation shall not damage the power supply Output noise (PARD) 120 mV Max P-P 100 mV Max P-P 12.0 V output 5.0 Vsb output Measured with a 0.1 uF ceramic and 10 uF tantalum capacitor on any output; 20 Mhz Output voltage overshoot 600 mV; 12 V main 250 mV; 5.0 standby 1 A/uSec slew rate Transient response +/-5% of regulation range 50% load step @ 1 A/us Step load valid between 10% to 100% of output rating Recovery time to within 1% of set point at onset of transient Max units in parallel Up to 6 Short circuit protection >130% of rated output Remote sense Compensation up to 100 mV Output isolation Standard per Safety Requirements Forced load sharing To within 10% of all shared outputs Digital sharing control Overload protection (OCP) 120% to 130% 120% to 170% 12 V output 5.0 Vsb output Overvoltage protection (OVP) 110% to 120% 110% to 125% 12 V output 5.0 Vsb output Overtemperature protection 10 - 15 ˚C above safe operating area Both PFC and output converter monitored Output to return DS800SL Series Data Sheet Outputs - All Models Timing Diagram AC On AC Input AC On T PWOK_Off_ T Vout_Holdup Main Vout T AC_On_Delay T PWOK_Off_ T PWOK_Off T PWOK_On T PWOK_Holdup T PWOK_On PWOK T sb_on_delay T PSON_PWOK T sb_On 5.0 Vsb Vout T PSON_On_Delay T SB_Vout PS_ON T ACOK_Delay AC_OK AC Input ON / OFF Cycle PSON ON / OFF Cycle DS800SL Series Data Sheet Outputs - All Models Turn On/Off Timing Item Description Min Max Units Tvout_rise +12 Output rise time 10 300 mSec Tvout_rise 5.0 Vsb output rise time 1 50 mSec Tsb_on_delay Delay from AC being applied to 5.0 Vsb being within regulation. 1500 mSec Tac_on_delay Delay from AC being applied to all output voltages being within regulation. 3000 mSec Tvout_holdup Time all output voltages, including 5.0 Vsb, stay within regulation after loss of AC. Tpwok_holdup Delay from loss of AC to de-assertion of PWOK. 5 Tpson_on_delay Delay from PSON# active to output voltages within regulation limits. 50 Tpson_pwok Delay from PSON# de-active to PWOK being de-asserted. Tacok_delay Delay from loss of AC input to de-assertion of ACOK#. 10 Tpwok_on Delay from output voltages within regulation limits to PWOK asserted at turn on. 100 1000 mSec Tpwok_off Delay from PWOK de-asserted to 12 Vdc or 5.0 Vsb dropping out of regulation limits. 1 1000 mSec Tpwok_low Duration of PWOK being in the de-asserted state during an off/on cycle using AC or the PSON# signal. 100 Tsb_vout Delay from 5.0 Vsb being in regulation to 12 Vdc being in regulation at AC turn on. 50 10 mSec mSec 2500 mSec 100 mSec mSec mSec 1000 mSec PSON # The PSON# signal is required to remotely turn on/off the power supply. PSON# is an active low signal that turns on the +12 Vdc power rail. When this signal is not pulled low by the system, or left open, the +12 Vdc output turns off. The Vsb output remains on. This signal is pulled to a standby voltage by a pull-up resistor internal to the power supply. The power supply fan(s) shall operate at the lowest speed. PSON Signal Characteristics Signal Type Accepts an open collector/drain input from the system. Pulled-up to the 5.0 Vsb located in power supply. PSON# = Low ON PSON# = Open OFF Logic level low (power supply ON) Logic level high (power supply OFF) MIN MAX 0V 0.8 V 2.0 V 5.2 V 5 msec 200 msec Source current, Vpson = low Power up delay: Tpson_on_delay 4 mA DS800SL Series Data Sheet PWOK# (POWER GOOD) PWOK is a power good signal and will assert HIGH when the outputs are within the regulation limits. PWOK will be pulled LOW by the power supply to indicate when either output falls below regulation limits or when AC power has been removed for a time sufficiently long so that power supply operation is no longer guaranteed. The start of the PWOK# delay time shall be inhibited as long as the +12 Vdc output is in current limit or the 5.0 Vsb output is below the regulation limit. PWOK Signal Characteristics Signal Type Open collector/drain output from power supply. Pullup to 5.0 Vsb external to the power supply. PWOK = High Power Good PWOK = Low Power Not Good To tLogic level low voltage, Ising = 4 mA Logic level high voltage, Isource = 200 µA MIN MAX 0V 0.8 V 2.0 V 5 .2V Sink current, PWOK = low 4 mA Source current, PWOK = high PWOK delay: Tpwok_on 2 mA 100 ms 1000 ms PWOK rise and fall time Power down delay: Tpson_off 100 µsec 1 msec 1000 msec PSKILL The +12 Vdc output only from the power supply shall be disabled if the PSKILL input is high and V Standby will continue to be provided, outputs may be enabled if this signal is low. The power supply includes a pull up to disable all outputs if this signal is open. PSKILL whall not be connected during a hot insertion before all of the other pins are connected. AC INPUT PRESENT INDICATOR (ACOK/L) The ACOK signal is used to indicate presence of AC input to the power supply. This signal shall be connected to Vsb through a resistor on the host system side. A logic “Low” level on this signal shall indicate AC input to the power supply is present. A Logic “High” on this signal shall indicate a loss of AC input to the power supply. ACOK# Signal Characteristics Signal Type Pull up to 5.0 Vsb through a resistor in the host system. Present = High Present Present = Low Not Present MIN MAX Logic level low voltage, Isink = 4 mA 0V 0.8 V Logic level high voltage, Isink = 50 µA 2.0 V 5.2 V Sink current, PRESENT = low 4 mA Sink current, PRESENT# = high 50 µsec # DS800SL Series Data Sheet STATUS INDICATIONS See table below for Summary of Status signals, Ports and Indicators. The condition column assumes 2 or more power supplies present and ON and 5.0 Vsb shared for management interface. On the “Fan Blocked” condition, the assumption is that all outputs are within spec and not over temperature. This would be considered a “warning” condition. On the “Standby” condition, the system differentiates this state by knowing PS_ONL in negated (requesting Standby). Status Indicators Condition Status Signals Status Register Shutdown Register LED’s ACOK/L PWOK/H PSON PWOK Fan-Fail AC-Loss 0-Temp 0-Current Fail AC DC Normal Operation 0 1 1 1 0 0 0 0 0 On On Off V1 12 V Overcurrent 0 0 1 0 0 0 0 1 1 On Off On AC Input Fail 1 0 1 0 0 1 0 0 1 Off Off Off Fan Blocked or Running Under Speed. O/P’s ok 0 1 1 1 0 0 0 0 0 On On Off UV on V1 12 V and PS Has Latched Off 0 0 1 0 0 0 0 0 1 On Off On UV on Vsb +5.0 and PS Has Turned Off 0 0 1 0 0 0 0 0 1 On Off On OV on V1 12V or Vsb +5.0 & PS Has Latched Off 0 0 1 0 0 0 0 0 1 On Off On Over Temp and PS Has Turned Off 0 0 1 0 0 0 1 0 1 On Off On Fan Below Shutdown Limit 0 0 1 0 1 0 0 0 1 On Off On No Problems But PS is in Standby Mode 0 0 0 0 0 0 0 0 0 On Off Off Output Connector and Pin Out Table Ground Pin 4 Ground S1 +12 V Sense S2 +12 V RTN Sense S3 +12 V Current Share S4 SMB_ALERT/L S5 SDA S6 SCL* S7 PSKILL S8 PSON/L S9 PW_OK S10 PS_A1 S11 +5.0 V_STBY S12 +5.0 V_STBY S13 Reserved S14 PRESENT/L S15 PS_A0 S16 Reserved S17 Reserved for factory use S18 EEPROM_WP S19 ACOK/L S20 Not used S21 PS_A2 S22 V_STBY Remote Sense S23 V_STBY S24 V_STBY * Supports I2C standard mode (100 kHz) only Top Side Ground Ground P3 P4 P1 S12 +12 V Pin 3 S24 +12 V Pin 2 S1 Signal Name Pin 1 S13 Pin +12V Bottom Side P2 +12V Note: Pin number may not necessarily match vendor’s pin number assignment. Please follow the signal and number assignment as indicated in this datasheet Fail DS800SL Series Data Sheet Mechanical Drawing BURN-IN 100% Burn-in at 45 ˚C, at 80-90% load. Duration of burn-in determined by Quality Assurance Procedures. MTBF The power supply has an MTBF of >400K hours using Telcordia SR-332 at full load, and 25 °C ambient. With the power supply installed in a system in a 25 ˚C ambient environment and operating at full load, capacitor life shall be 5 years, minimum for ALL electrolytic capacitors contained within this power supply. T QUALITY ASSURANCE Full QAV testing shall be conducted in accordance with Artesyn Embedded Technologies Standards with reports available upon request. WARRANTY Artesyn Embedded Technologies shall warrant the power supply to be free of defects in materials and workmanship for a minimum period of two years from the date of shipment, when operated within specifications. The warranty shall be fully transferable to the end owner of the equipment powered by the supply. WORLDWIDE OFFICES Americas Europe (UK) Asia (HK) 2900 S.Diablo Way Tempe, AZ 85282 USA +1 888 412 7832 Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX United Kingdom +44 (0) 1384 842 211 14/F, Lu Plaza 2 Wing Yip Street Kwun Tong, Kowloon Hong Kong +852 2176 3333 While every precaution has been taken to ensure accuracy and completeness in this literature, Artesyn Embedded Technologies assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. © 2015 Artesyn Embedded Technologies, Inc. www.artesyn.com For more information: www.artesyn.com/power For support: [email protected] DS800SL DS 29Jul2015