7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. ATLANTIC VERSION TERMINATOR INTERFACE ADAPTER 5 4 3 2 20 DESCRIPTION REVISION 2151061 -1 D 2151061 -2 2151061 -5 SMART APPLICATOR MECHANICAL FEED PNEUMATIC SERVO LATCH PLATE SMART APPLICATOR MECHANICAL FEED FINE CRIMP HEIGHT ADJUST SERVO LATCH PLATE 12 D NON-CRIMP HEIGHT ADJUST 2151061 -7 D FINE CRIMP HEIGHT ADJUST A SERVO LATCH PLATE SERVO LATCH PLATE 2151061 -6 7- 2151061 -7 PNEUMATIC FEED MECHANICAL FINE CRIMP HEIGHT ADJUST D CONVERT TO 4 NONE CRIMP TOOLING KIT - 4 PNEUMATIC FEED - - - CRIMP WIRE INSUL SIZE 2.03 mm [.080] 2.79 mm [.110] APPLICATOR INSTRUCTIONS 408-10389 2119950-1 1338685-1 2161326-1 - 2119951-1 5-18022-5 - 2119949-1 8- 2151061 -5 8- 2151061 -4 1338685-1 2119951-1 5-18022-5 - 2161326-1 8- 2151061 -5 - 2119949-1 8- 2151061 -4 1338685-1 2119950-1 5-18022-5 1338685-1 - 5-18022-5 - - - - - - - - - - - 2119641-1 2119799-1 - - 1901094-3 2119653-1 1901094-3 - 2119653-1 2119641-1 - - - 2168400-6 2168400-6 - 2119799-1 - (QUANTITY 2) - - - - - (QUANTITY 2) - - - - - 2063440-1 - - - - 6 - - - - - - - TYPE - F O - - TE TERMINAL TE CRIMP SPECIFICATION WIRE STRIP LENGTH n 3.70-4.30 mm [.146-.169 IN] C - TYPE A TAB / MICRO TIMER CONTACT TERMINAL NAME: TERMINAL APPLICATION SPECIFICATION (A) 114-18081 (B) 114-18082 - INSULATION DIAMETER RANGE - 2.20-2.40 mm [.087-.094 IN] - - - - - - - TERMINALS APPLIED TE TERMINAL (A) 1241844-2 (A) 1241844-3 TE TERMINAL (B) 1241846-1 C1__DWG_PN_1_0 C1__DWG_PN_1_1 (B) 1241846-2 C1__DWG_PN_1_2 C1__DWG_PN_2_0 C1__DWG_PN_2_1 TE TERMINAL (B) 1241846-3 C1__DWG_PN_3_0 - TE TERMINAL - C1__DWG_PN_4_0 - C1__DWG_PN_3_1 6 C1__DWG_PN_2_2 - WIRE SIZE 1.50mm2 CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 1.66+/-0.05 [.065+/-.002] CRIMP HEIGHT REFERENCE SETTING - 9 7.9 W1__DWG_CRIMP_HT_1 - W1__FA_SETTING_1 6 - - B 1 RECOMMENDED SPARE PARTS - 2 GREASE BEARING SURFACES LIGHTLY - - 3. LUBRICATE DAILY PER THE APPLICATOR INSTRUCTION SHEET SUPPLIED WITH THE APPLICATOR. 4 6 APPLICATOR SPECIFIC DATA TO BE ENTERED INTO BLANK MEMORY CHIP AT ASSEMBLY. SEE BELOW FOR PART NUMBER: MECHANICAL FEED WITH "SMART APPLICATOR" CONVERSION: 8PNEUMATIC FEED WITH "SMART APPLICATOR" CONVERSION: 8SERVO FEED WITH "FINE CRIMP HEIGHT ADJUST": 8SERVO FEED WITH "NON-CRIMP HEIGHT ADJUST": 8- 2151061 2151061 2151061 2151061 7 8 9 10 11 A 12 APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEM 50 APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. FOR -6 ONLY APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEM 37. GREASE THREADS, GROOVE AND O-RING ON ITEMS 35 & 252. MAGNET, ITEM 166 MUST BE ORIENTED CORRECTLY IN ORDER TO PROPERLY ACTUATE THE COUNTER. CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. SPARE FEED CAM STORAGE LOCATION REFER TO INSTRUCTION SHEET FOR ADDITIONAL INFORMATION. TO CONVERT THE APPLICATOR TO A NON-CARRIER CUTTING STYLE, REMOVE ITEM 13 AND ATTACH TO THE LOCATION ON THE BACK SIDE OF THE HOUSING. REFER TO INSTRUCTION SHEET FOR ADDITIONAL INFORMATION. WHEN ASSEMBLING -6 NON-CRIMP HEIGHT ADJUST APPLICATOR USE SHIM PACK 2119957-2 TO ALIGN APPLICATOR'S MAXIMUM WIRE CRIMP HEIGHT AT NORMAL TERMINATOR SHUT HEIGHT -4 -4 -5 -6 - & 62. - *WARNING ON INSTALLATION, SET WIRE DISC, ITEM 40 TO LARGEST WIRE SIZE SETTING. USE OF SETTINGS BELOW MINIMUM REQUIRED CRIMP HEIGHT SETTING WILL CAUSE DAMAGE TO CRIMP TOOLING. 1 1 1 1 - 1 - -77 -7 1 - -6 1 - -5 1 1 -2 - 2119957-2 8-21084-0 2119640-1 -1 PART NO 1 APPLICATOR SHIM PACK O-RING, .676 ID, .070 DIA. MAT. PUSH ROD, AIR FEED DESCRIPTION 1 2119957-2 1 8-21084-0_GATD 1 2119640-1 260 252 250 1 - 1 1 1 1 ITEM NO - 1 1 1 1 1 1 1 1 1 1 1 REF 1 1 1 1 1 2 1 3 1 4 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - - - 1 P LTR - - 1 1 - 1 1 2 1 1 1 REF REF REF REF - - - 1 - - 1 - 1 1 1 1 1 1 -6 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 - 1 - 1 1 2 - - - 1 1 - 1 1 1 - - 1 1 1 - 4 1 1 - 1 4 1 1 1 1 4 1 1 1 - 1 3 1 - 4 1 3 1 - 2 1 3 - 1 2 1 1 1 1 2 - 1 1 - - 1 1 1 2 - 1 1 - 1 - 1 1 - 1 REF REF 1 - - 1 1 - - 1 1 - 1 REF REF 1 - 1 1 -5 -2 mm MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.5 0.13 0.013 0.0001 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - XZ GB D ECR-14-009626 26JUN2014 YY TE D1 ECR-14-014274 24SEP2014 YY UG D2 ECR-15-009423 23JUN2015 YY GB BUSHING, LCH5-12, MISUMI FEED CAM, AIR FEED DETENT PIN SPRING, COMPRESSION RAM, AMP STYLE, SIDE FEED, NON-ADJ. CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 SHCS, LOW HEAD, RoHS, M5 X 16 MECHANICAL FEED ASSEMBLY AIR FEED MODULE TAG,IDENTIFICATION SPACER, FEEDER PIN, SLOTTED SPRING 3.0 X 20.0 SPRING, COMPRESSION GUIDE PIN,HOLDDOWN GUIDE PIN,HOLDDOWN RING, RETAIN, EXTERN, 3/16 CRESCENT MAGNET, RARE EARTH HIGH ENERGY COUNTER, MAGNETIC SPRING, FEED FINGER PIN, RETAIN, GRVD, 3/16 X .854 HOLDER,FEED FINGER, AF MEMORY CHIP, PROGRAMMED SERVO FEED LATCH ASM WASHER, FLAT, REG M4 FEED FINGER ASSEMBLY,SF SPACER, CRIMPER DOCUMENTATION PACKAGE DEPRESSOR, WIRE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 LIMITER, ADJUSTMENT BOLT SCR, SET, SOC, CONE POINT, M3 x 4.0 SCR, BHSC, RoHS (M4 X 8) SCR, HEX HD CAP, M4 X 6.0 PAWL, FEED SHCS, LOW HEAD, RoHS, M4 X 12 NUT, HEX, REG, RoHS, M3.5 HOLDDOWN, TERMINAL STANDOFF,HOLD-DOWN SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM, AMP STYLE, SIDE FEED SCR, BHSC, RoHS (M8 X 25) DISC, NUMBERED FA WIRE ADJUSTMENT APPLICATOR SHIM PACK RAM WASHER, PRECISION FA HEAD, ATLANTIC STYLE BOLT, ADJUSTMENT SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) HEX HEAD, FLANGED, M5 x 8mm LONG SPACER, STRIP GUIDE ASSEMBLY, STRIP GUIDE STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION SPECIAL SPACER, CRIMPER CRIMPER, WIRE PREMIUM DWN 13APR2011 CHK 13APR2011 APVD 13APR2011 C.CHEN S.XI I.CRUZ NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 1 2119798-1 1 1-22279-3_SIMP 1 2119758 1 2119082-9 1 2079764 1 2119083 1 7-18023-7 2 2168400-6 1 2119580-1 1 2063440-1 1 2119740-2 .. 1 1901094-3 1 993111-1 1 8-22280-7_SIMP 1 1752353-2 1 1901680-2 2 21045-3 1 994969-1_GATD 1 COUNTER_994970 1 240638 1 3-23627-7 1 2119799 1 1901689_EMPTY_OCEAN_SF .. 1 1633743-1 1 1-18028-2 1 2119944-1 1 455888-5 1 2119956-1 1 2119791-5 1 2119740-1 2 2168078-1 1 2119793 3 992763-5 1 2079383-4 1 5-18022-5 1 1338685-1 4 2168400-1 1 1-5018030-0 1 1901681-1 1 1-1752354-9 3 18023-9 1 2119652 1 2119653 1 2119656-9 1 2119370 1 2079383-7 1 2119645 1 2119957-1 1 2119644-2 1 2119085 1 2119092-1 1 3-1752356-3 2 2079383-5 1 2161328 1 1320908-8 1 2119959-2 1 1320928-1 1 2168083-2 1 1-18028-2 1 2119533 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 454276-5 1 5-1333204-0 1 2119757-8 1 238011-2 1 1633996-7 1 455888-2 1 1-456405-6 249 248 247 246 245 244 243 242 241 240 239 238 213 198 177 176 175 174 172 166 164 163 137 136 135 133 119 117 82 71 70 67 66 63 62 60 59 56 54 52 51 50 49 48 47 46 44 41 40 39 38 37 35 34 33 32 30 29 24 21 20 19 13 12 11 10 9 8 5 4 3 2 1 ITEM NO Harrisburg, PA 17105-3608 - WEIGHT 1 2119641-1 TE Connectivity APPLICATION SPEC - 1 2079988_GATD DESCRIPTION PRODUCT SPEC - APVD 28APR2014 PART NO - DWN ECR-14-006236 -1 1 DATE C2 1 1 1 - 1 1 1 1 - 1 1 1 1 - 1 1 1 - - 1 1 - - 1 1 1 1 1 1 - - - 1 1 - - - 1 1 2 - 1 1 1 2 1 1 1 1 - 1 1 1 1 - 1 1 1 1 - 1 - 1 DESCRIPTION 2079988-1 2119641-1 2119798-1 1-22279-3 2119758-1 2119082-9 2079764-1 2119083-1 7-18023-7 2168400-6 2119580-1 2063440-1 2119740-2 1901094-3 993111-1 8-22280-7 1752353-2 1901680-2 21045-3 994969-1 994970-2 240638-1 3-23627-7 2119799-1 SEE NOTE 4 1633743-1 1-18028-2 2119944-1 455888-5 2119956-1 2119791-5 2119740-1 2168078-1 2119793-1 992763-5 2079383-4 5-18022-5 1338685-1 2168400-1 1-5018030-0 1901681-1 1-1752354-9 18023-9 2119652-1 2119653-1 2119656-9 2119370-1 2079383-7 2119645-1 2119957-1 2119644-2 2119085-1 2119092-1 3-1752356-3 2079383-5 2161328-1 1320908-8 2119959-2 1320928-1 2168083-2 1-18028-2 2119533-1 2119806-1 3-22280-3 1-356885-4 2119805-1 454276-5 5-1333204-0 2119757-8 238011-2 1633996-7 455888-2 1-456405-6 - THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: & 4 of 4) - -77 -7 ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 AMP 4805 REV 31MAR2000 - 5. ADJUSTMENT OF THE STRIPPER MAY BE REQUIRED WHEN MOVING THE APPLICATOR BETWEEN BENCH AND LEADMAKER APPLICATIONS. 6 66 2063440-1 - TERMINAL DATA: REVISIONS PART NUMBERS REQUIRED - APPLICATOR DATA 1 DIST A 2119599-1 APPLICATOR STYLE CONVERSION CHART FEED TYPE FINE CRIMP HEIGHT ADJUST D LOC SET UP GAUGE ALL RIGHTS RESERVED. PART NUMBER D 6 Ocean Side Feed Applicator - DRAWING NO 2151061 SCALE 1:2 RESTRICTED TO SHEET 1 OF - 4 & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION REV D2 D C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 6 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. 1 REVISIONS DIST 66 P LTR DESCRIPTION SEE SHEET 1 - FEED TYPE MECHANICAL A D 6 37 6 62 59 38 56 39 250 247 246 260 44 7 252 245 35 244 2 7 249 63 A 166 242 82 1 2 2 2 6 2 34 REF 2 C 3 1 177 56 SERVO LATCH PLATE 4 2 176 2 4.3 0.5 [ 0.17 0.01 ] REF 1 172 TERMINAL SUPPORT LOCATION 70 5 41 174 44 135 2 175 51 6 164 A 19.1 [.75] 66 50 2 67 11 213 33 24 SERVO FEEDER NOT INCLUDED 117 REF 10 REF 245 REF 52 198 B D 8 137 4 - 2 163 136 133 - - 8 59 240 APVD 243 238 C DWN 40 239 PNEUMATIC DATE A 50 REF HOLDDOWN SET-UP 19 30 20 29 21 B 9 1 12 ITEM 30 LOCATED AT REAR HOLES 241 13 1 11 CAM POSITIONS 30mm STROKE 30mm STROKE 30mm STROKE 47 46 32 34 54 8 1 60 54 10 1 119 30 REF 29 REF 11 FEED TRACK POSITION GUIDE BY WIRE BARREL 248 48 A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 49 40mm STROKE MECHANICAL POST FEED AMP 4805 REV 31MAR2000 49 40mm STROKE MECHANICAL PRE FEED 49 40mm STROKE AIR FEED DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.5 0.13 0.013 0.0001 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 13APR2011 CHK 13APR2011 APVD 13APR2011 C.CHEN S.XI I.CRUZ TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 Ocean Side Feed Applicator - DRAWING NO 2151061 SCALE 1:2 RESTRICTED TO SHEET 2 OF & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION - 4 REV D2 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. PACIFIC VERSION TERMINATOR INTERFACE ADAPTER 5 4 3 2 20 SET UP GAUGE 2119599-1 ALL RIGHTS RESERVED. PART NUMBER REVISION 2- 2151061 -1 DESCRIPTION D 2- 2151061 -2 D 6 FEED TYPE FINE CRIMP HEIGHT ADJUST D FINE CRIMP HEIGHT ADJUST D FINE CRIMP HEIGHT ADJUST 2- 2151061 -7 D FINE CRIMP HEIGHT ADJUST NONE CRIMP TOOLING KIT PNEUMATIC FEED SERVO LATCH PLATE SMART APPLICATOR MECHANICAL FEED PNEUMATIC 2- 2151061 -5 A CONVERT TO MECHANICAL SERVO LATCH PLATE 7- 2151061 -7 APPLICATOR STYLE CONVERSION CHART - SERVO LATCH PLATE SMART APPLICATOR MECHANICAL FEED 4 PNEUMATIC FEED - - CRIMP WIRE INSUL SIZE 2.03 mm [.080] 2.79 mm [.110] APPLICATOR INSTRUCTIONS 408-10389 2119950-1 1338685-1 2161326-1 - 2119951-1 2119949-1 2119951-1 2161326-1 2119949-1 2119950-1 - - - 1338685-1 - - 1338685-1 1338685-1 - 5-18022-5 8- 2151061 -5 8- 2151061 -4 5-18022-5 8- 2151061 -5 8- 2151061 -4 5-18022-5 5-18022-5 - 2119641-2 2119799-1 - - 1901094-3 2119653-2 1901094-3 - 2119653-2 2119641-2 - - - - - 2168400-6 2168400-6 - 2119799-1 - (QUANTITY 2) - - - - - (QUANTITY 2) - - - - - 2063440-1 - - - 6 - - - - - TYPE - F O - WIRE STRIP LENGTH n 3.70-4.30 mm [.146-.169 IN] C - TE CRIMP SPECIFICATION - TYPE A TAB / MICRO TIMER CONTACT TERMINAL NAME: TERMINAL APPLICATION SPECIFICATION (A) 114-18081 (B) 114-18082 - INSULATION DIAMETER RANGE - 2.20-2.40 mm [.087-.094 IN] - - - - - - - TERMINALS APPLIED TE TERMINAL (A) 1241844-2 (A) 1241844-3 TE TERMINAL C1__DWG_PN_1_0 (B) 1241846-1 (B) 1241846-2 C1__DWG_PN_1_1 C1__DWG_PN_1_2 C1__DWG_PN_2_0 C1__DWG_PN_2_1 TE TERMINAL C1__DWG_PN_3_0 (B) 1241846-3 - TE TERMINAL - C1__DWG_PN_4_0 - C1__DWG_PN_3_1 - C1__DWG_PN_2_2 - WIRE SIZE 1.50mm2 CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 1.66+/-0.05 [.065+/-.002] CRIMP HEIGHT REFERENCE SETTING W1__DWG_CRIMP_HT_1 7.9 - 9 - W1__FA_SETTING_1 - 6 - 6 - B 1 RECOMMENDED SPARE PARTS 2 GREASE BEARING SURFACES LIGHTLY - 3. LUBRICATE DAILY PER THE APPLICATOR INSTRUCTION SHEET SUPPLIED WITH THE APPLICATOR. 4 - APPLICATOR SPECIFIC DATA TO BE ENTERED INTO BLANK MEMORY CHIP AT ASSEMBLY. SEE BELOW FOR PART NUMBER: MECHANICAL FEED WITH "SMART APPLICATOR" CONVERSION: 8PNEUMATIC FEED WITH "SMART APPLICATOR" CONVERSION: 8SERVO FEED WITH "FINE CRIMP HEIGHT ADJUST": 8- - - 2151061 -4 2151061 -4 2151061 -5 - 5. ADJUSTMENT OF THE STRIPPER MAY BE REQUIRED WHEN MOVING THE APPLICATOR BETWEEN BENCH AND LEADMAKER APPLICATIONS. 6 7 8 9 10 A 11 - APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEM 50 APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. GREASE THREADS, GROOVE AND O-RING ON ITEMS 139 & 152. MAGNET MUST BE ORIENTED CORRECTLY IN ORDER TO PROPERLY ACTUATE THE COUNTER. CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. & 62. - 1 *WARNING ON INSTALLATION, SET WIRE DISC, ITEM 40 TO LARGEST WIRE SIZE SETTING. USE OF SETTINGS BELOW MINIMUM REQUIRED CRIMP HEIGHT SETTING WILL CAUSE DAMAGE TO CRIMP TOOLING. - 1 - 1 1 1 - 1 1 SPARE FEED CAM STORAGE LOCATION REFER TO INSTRUCTION SHEET FOR ADDITIONAL INFORMATION. 1 1 TO CONVERT THE APPLICATOR TO A NON-CARRIER CUTTING STYLE, REMOVE ITEM 13 AND ATTACH TO THE LOCATION ON BACK SIDE OF THE HOUSING. REFER TO INSTRUCTION SHEET FOR ADDITIONAL INFORMATION. P 1 1 - 1 LTR DESCRIPTION DATE SEE SHEET 1 - - 1 - 1 1 1 2 1 REF 1 1 - 1 1 1 1 - 1 1 1 1 - 1 1 1 - - 1 1 - - 1 1 1 1 1 - - - - - 1 - - - 1 1 2 - 1 1 1 - 1 1 1 1 1 1 1 1 - 1 1 1 - 1 1 2119782-1 2119640-1 2079988-1 1-22279-3 2119082-9 2079764-1 2119083-1 7-18023-7 2168400-6 2119580-1 2063440-1 2119740-2 1901094-3 993111-1 8-22280-7 1752353-2 1901680-2 21045-3 994969-1 994970-2 240638-1 8-21084-1 2119641-2 2119798-2 2079383-8 2168400-5 2119653-2 1-2119656-0 2119650-1 2119092-2 3-23627-7 2119799-1 SEE NOTE 4 1633743-1 1-18028-2 2119944-1 455888-5 2119956-1 2119791-5 2119740-1 2168078-1 2119793-1 992763-5 5-18022-5 1338685-1 1-5018030-0 1901681-1 1-1752354-9 18023-9 2119652-1 2079383-7 2119645-1 2119957-1 2119644-3 3-1752356-3 2079383-5 2161328-1 1320908-8 2119959-2 1320928-1 2168083-2 1-18028-2 2119533-1 2119806-1 3-22280-3 1-356885-4 2119805-1 454276-5 5-1333204-0 2119757-8 238011-2 1633996-7 455888-2 1-456405-6 1 - 1 1 REF REF REF - - 1 1 1 - 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 2 - 1 1 1 1 - 1 1 1 - - 1 1 1 - 1 1 1 1 1 1 1 1 3 1 - 1 1 3 - - 2 1 3 - 1 2 1 3 1 1 2 1 1 1 - 2 1 1 1 1 - 1 1 1 1 - 1 1 - 1 REF 1 - - 1 - - - 1 1 - 1 REF - 1 1 - - 1 1 - - 1 1 1 - 1 1 1 1 4 - 1 1 1 4 - 1 1 1 4 - - 1 1 4 1 1 1 1 - 1 1 1 1 1 1 DWN APVD - - THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 mm & 2 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.5 0.13 0.013 0.0001 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - FINE ADJUST HEAD ASM, PACIFIC STYLE PUSH ROD, AIR FEED BUSHING, LCH5-12, MISUMI SPRING, COMPRESSION CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 SHCS, LOW HEAD, RoHS, M5 X 16 MECHANICAL FEED ASSEMBLY AIR FEED MODULE TAG,IDENTIFICATION SPACER, FEEDER PIN, SLOTTED SPRING 3.0 X 20.0 SPRING, COMPRESSION GUIDE PIN,HOLDDOWN GUIDE PIN,HOLDDOWN RING, RETAIN, EXTERN, 3/16 CRESCENT MAGNET, RARE EARTH HIGH ENERGY COUNTER, MAGNETIC SPRING, FEED FINGER O-RING, .801 ID, .070 DIA. MAT. FEED CAM, AIR FEED DETENT PIN SCR, BHSC, RoHS (M4 X 16) SHCS, LOW HEAD, RoHS, M4 X 20 FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM, ASIAN STYLE, SIDE FEED BOLT, ADJUSTMENT PIN, RETAIN, GRVD, 3/16 X .854 HOLDER,FEED FINGER, AF MEMORY CHIP, PROGRAMMED SERVO FEED LATCH ASM WASHER, FLAT, REG M4 FEED FINGER ASSEMBLY,SF SPACER, CRIMPER DOCUMENTATION PACKAGE DEPRESSOR, WIRE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 LIMITER, ADJUSTMENT BOLT SCR, SET, SOC, CONE POINT, M3 x 4.0 SCR, HEX HD CAP, M4 X 6.0 PAWL, FEED NUT, HEX, REG, RoHS, M3.5 HOLDDOWN, TERMINAL STANDOFF,HOLD-DOWN SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED SCR, BHSC, RoHS (M8 X 25) DISC, NUMBERED FA WIRE ADJUSTMENT APPLICATOR SHIM PACK RAM WASHER, PRECISION SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) HEX HEAD, FLANGED, M5 x 8mm LONG SPACER, STRIP GUIDE ASSEMBLY, STRIP GUIDE STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION SPECIAL SPACER, CRIMPER CRIMPER, WIRE PREMIUM PART NO -77 -27 -25 -22 -21 PACIFIC VERSION AMP 4805 REV 31MAR2000 66 - 2063440-1 - TE TERMINAL A PART NUMBERS REQUIRED - TERMINAL DATA: REVISIONS DIST - - APPLICATOR DATA LOC 1 DWN 13APR2011 CHK 13APR2011 APVD 13APR2011 C.CHEN S.XI I.CRUZ NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 1 1-22279-3_SIMP 1 2119082-9 1 2079764 1 2119083 1 7-18023-7 2 2168400-6 1 2119580-1 1 2063440-1 1 2119740-2 .. 1 1901094-3 1 993111-1 1 8-22280-7_SIMP 1 1752353-2 1 1901680-2 2 21045-3 1 994969-1_GATD 1 COUNTER_994970 1 240638 1 8-21084-1_GATD 1 2119641-2 1 2119798-2 1 2079383-8 4 2168400-5 1 2119653-2 1 1-2119656-0 1 2119650 1 2119092-2 1 3-23627-7 1 2119799 1 1901689_EMPTY_OCEAN_SF .. 1 1633743-1 1 1-18028-2 1 2119944-1 1 455888-5 1 2119956-1 1 2119791-5 1 2119740-1 2 2168078-1 1 2119793 3 992763-5 1 5-18022-5 1 1338685-1 1 1-5018030-0 1 1901681-1 1 1-1752354-9 3 18023-9 1 2119652 1 2079383-7 1 2119645 1 2119957-1 1 2119644-3 1 3-1752356-3 2 2079383-5 1 2161328 1 1320908-8 1 2119959-2 1 1320928-1 1 2168083-2 1 1-18028-2 1 2119533 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 454276-5 1 5-1333204-0 1 2119757-8 1 238011-2 1 1633996-7 1 455888-2 1 1-456405-6 ITEM NO Harrisburg, PA 17105-3608 - WEIGHT 1 2079988_GATD 251 250 249 246 244 243 242 241 240 239 238 213 198 177 176 175 174 172 166 164 163 152 151 145 144 143 142 141 140 139 137 136 135 133 119 117 82 71 70 67 66 63 62 59 56 52 51 50 49 48 41 40 39 38 34 33 32 30 29 24 21 20 19 13 12 11 10 9 8 5 4 3 2 1 TE Connectivity APPLICATION SPEC - 1 2119640-1 DESCRIPTION PRODUCT SPEC - 1 2119782 Ocean Side Feed Applicator - DRAWING NO 2151061 SCALE 1:2 RESTRICTED TO SHEET 3 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV D2 D C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT RELEASED FOR PUBLICATION 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 20 6 1 REVISIONS DIST 66 P LTR DESCRIPTION SEE SHEET 1 - FEED TYPE 6 APVD - - - 62 40 A 145 38 239 39 59 152 7 56 246 140 2 D 2 2 244 7 139 243 PNEUMATIC 250 2 8 249 A 166 242 2 6 4.3 0.5 [ 0.17 0.01 ] 63 238 REF 8 163 34 59 82 136 1 137 C 172 177 56 176 2 SERVO LATCH PLATE 2 1 133 4 135 2 REF TERMINAL SUPPORT LOCATION 2 3 C 1 4 70 174 5 41 52 240 140 REF 175 51 198 164 6 66 50 67 33 SERVO FEEDER NOT INCLUDED 213 A 24 50 19 10 30 19.1 [.75] 2 11 A B DWN 251 MECHANICAL D DATE REF HOLDDOWN SET-UP 20 117 REF 9 21 29 B 1 12 241 13 CAM POSITIONS 30mm STROKE ITEM 30 LOCATED AT REAR HOLES 11 30 11 30mm STROKE 30mm STROKE 142 1 151 REF REF 29 119 141 32 34 143 8 1 144 143 10 1 FEED TRACK POSITION GUIDE BY WIRE BARREL 48 A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. PACIFIC VERSION 49 MECHANICAL POST FEED 49 MECHANICAL PRE FEED 49 AIR FEED Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 DIMENSIONS: mm & 2 of 4) MATERIAL AMP 4805 REV 31MAR2000 - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.5 0.13 0.013 0.0001 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 13APR2011 CHK 13APR2011 APVD 13APR2011 C.CHEN S.XI I.CRUZ TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 Ocean Side Feed Applicator - DRAWING NO 2151061 SCALE 1:2 RESTRICTED TO SHEET 4 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV D2