Datasheet Load Switch ICs 0.5A Current Load Switch ICs for Portable Equipment BD6524HFV General Description Key Specifications BD6524HFV is a high side switch IC using an N-Channel MOSFET and used as a power switch for in memory card slot. This switch has an ON-Resistance of 200mΩ (Typ). Operations using low input voltage (V IN ≥ 3.0V) are possible for various switch applications. The switch turns ON slowly by the built-in charge pump; therefore, it is possible to reduce inrush current during switch ON. There is no parasitic diode between the drain and the source so reverse current flowing at switch OFF is prevented. Furthermore, it has a discharge circuit that releases electric charge from capacitive load at switch OFF. This IC is available in a space-saving HVSOF6 package. Input Voltage Range: ON-Resistance: (V IN =5V) (V IN =3.3V) Continuous Current: Standby Current: Operating Temperature Range: Package W(Typ) 3.0V to 5.5V 200mΩ(Typ) 250mΩ(Typ) 0.5 A 0.1μA (Typ) -25°C to +75°C D(Typ) H (Max) Features Built in N-MOS Switch with Low ON-Resistance (200mΩ, Typ) Maximum Output Current : 500mA Soft Start Function Under Voltage Lockout (UVLO) Protection Built in Discharge Circuit: Operations at Switch OFF, UVLO Reverse Current Flow Blocking at Switch OFF Condition HVSOF6 1.60mm x 3.00mm x 0.75mm Applications Memory Card Slots for Notebook PC, Digital still Camera, Portable Music Player, Compact Portable Devices such as PDA and so forth. Typical Application Circuit IN OUT IN OUT LOAD 0.1μF to 1μF EN GND EN ○Product structure：Silicon monolithic integrated circuit ○This product has not designed protection against radioactive rays www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･14･001 1/17 TSZ02201-0E3E0H300260-1-2 21.Aug.2014 Rev.002 Datasheet BD6524HFV Block Diagram GND IN 1,2 4 Charge Pump EN OUT 5,6 Control Logic 3 Pin Configuration (TOP VIEW) 1 IN OUT 6 2 IN OUT 5 3 EN GND 4 Pin Description Pin No. 1 Symbol Pin Function IN Switch input pin. When in use, connect each pin outside. 3 EN Switch control input pin (hysteresis input) Switch ON at High. 4 GND Ground OUT Switch output pin When in use, connect each pin outside. 2 5 6 www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 2/17 TSZ02201-0E3E0H300260-1-2 21.Aug.2014 Rev.002 Datasheet BD6524HFV Absolute Maximum Ratings Parameter Symbol Rating Unit Supply Voltage V IN -0.3 to +6.0 V Control Input Voltage V EN -0.3 to V IN +0.3 V Switch Output Voltage V OUT -0.3 to +6.0 V Storage Temperature Tstg -55 to +150 °C Power Dissipation Pd 0.85 (Note 1) W o o (Note 1) Mounted on 70mm x 70mm x 1.6mm glass-epoxy PCB. Derating : 6.8mW/ C above Ta=25 C. Caution: Operating the IC over the absolute maximum ratings may damage the IC. The damage can either be a short circuit between pins or an open circuit between pins and the internal circuitry. Therefore, it is important to consider circuit protection measures, such as adding a fuse, in case the IC is operated over the absolute maximum ratings. Recommended Operating Conditions Parameter Rating Symbol Min Typ Unit Max Supply Voltage V IN 3.0 - 5.5 V Operating Temperature Topr -25 - +75 °C Switch Current I OUT - - 500 mA Electrical Characteristics (Unless otherwise specified, Ta = 25°C, V IN = 5V) I DD I STB Min - Limit Typ 50 0.1 Max 75 1 EN Input Leak Current V ENH V ENL I EN 0.7 -1 +0.01 Switch ON-Resistance R ON Switch Leak Current I LEAK - Switch Rise Time Switch Rise Delay Time Switch Fall Time Switch Fall Delay Time t ON1 t ON2 t OFF1 t OFF2 UVLO Threshold Voltage Discharge Resistance Discharge Current Parameter Operating Current Standby Current EN Input Voltage Symbol Unit Conditions µA µA V EN = 5V, V OUT = Open V EN = 0V, V OUT = Open 2.5 +1 V V µA High Level Input Voltage Low Level Input Voltage 200 250 - 255 335 10 mΩ mΩ µA V IN = 5V V IN = 3.3V At Switch OFF - 0.4 0.5 1 2 0.8 1.0 2 4 ms ms µs µs R L =10Ω. Refer to the Timing Diagram in Figure 2. V UVLO 1.9 1.8 2.2 2.1 2.5 2.4 V V R DISC I DISC 0.8 200 1.8 350 - Ω mA Measurement Circuit R L =10Ω. Refer to the Timing Diagram in Figure 2. R L =10Ω. Refer to the Timing Diagram in Figure 2. R L =10Ω. Refer to the Timing Diagram in Figure 2. V IN Increasing V IN Decreasing V EN = 0V, I L = 1mA V EN = 0V, V IN = V OUT = 1.8V Timing Diagram IN OUT IN OUT EN GND tOFF1 tON1 VOUT RL 90% 90% 10% CL 10% tON2 tOFF2 VEN VENH Figure 1. Measurement Circuit www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 VENL Figure 2. Timing Diagram 3/17 TSZ02201-0E3E0H300260-1-2 21.Aug.2014 Rev.002 Datasheet BD6524HFV Typical Performance Curves 0.10 45 40 Standby Current : ISTB[μA] Stanby Current:ISTB[uA] Operating Current : IDD[μA] OPERATING CURRENT:IDD[uA] 50 35 30 25 20 15 10 From above: VIN=5.5V, 5.0V, 3.0V 5 0 -25 0 25 50 VIN=5V 0.08 0.06 0.04 0.02 0.00 75 -25 AmbientTEMPERATURE:Ta[ Temperature : Ta[°C] ℃] AMBIENT 25 50 75 Figure 4. Standby Current vs Ambient Temperature 2.5 2.5 2.0 2.0 EN Input Voltage:VENL[V] EN Input Voltage:VENH[V] Figure 3. Operating Current vs Ambient Temperature 1.5 1.0 From above: VIN=5.5V, 5.0V, 3.0V 0.5 0 Ambient Temperature : Ta[°C] ℃] Ambient Temperature:Ta[ 1.5 1.0 0.5 From above: VIN=5.5V, 5.0V, 3.0V 0.0 0.0 -25 0 25 50 -25 75 AmbientTemperature:Ta[℃] Temperature : Ta[°C] Ambient Figure 5. EN Input Voltage vs Ambient Temperature (High Level Input Voltage) www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 0 25 50 75 ℃] Ambient : Ta[°C] Ambient Temperature Temperature:Ta[ Figure 6. EN Input Voltage vs Ambient Temperature (Low Level Input Voltage) 4/17 TSZ02201-0E3E0H300260-1-2 21.Aug.2014 Rev.002 Datasheet BD6524HFV Typical Performance Curves - continued 0.9 0.8 300 Switch Rise Time : tON1[ms] Turn ON Time1:t ON1[ms] Switch :R ON[mΩ] ONON-Resistance Resistance:R ON [mΩ] 350 250 200 150 100 From above: VIN=3.0V, 5.0V, 5.5V 50 0.6 0.5 0.4 0.3 0.2 From above: VIN=3.0V, 4.0V, 5.0V, 5.5V 0.1 0 0 -25 0 25 50 -25 75 0 25 50 75 AmbientTemperature:Ta[ Temperature : Ta[°C] ℃ Ambient ℃] AmbientTemperature:Ta[ Temperature : Ta[°C] Ambient Figure 7. Switch ON-Resistance vs Ambient Temperature Figure 8. Switch Rise Time vs Ambient Temperature 0.9 3.5 0.8 3.0 0.7 Switch Fall Time1:t Time : tOFF1 Turn OFF 1[us] OFF[μs] Switch Rise Time :[ms] tON2[ms] Turn ONDelay Time2:t ON2 0.7 0.6 0.5 0.4 0.3 0.2 From above: VIN=3.0V, 4.0V, 5.0V, 5.5V 0.1 2.5 2.0 From above: VIN=3.0V, 4.0V, 5.0V, 5.5V 1.5 1.0 0.5 0.0 -25 0 25 50 75 0.0 AmbientTemperature:Ta[℃] Temperature : Ta[°C] Ambient -25 0 25 50 Ambient Temperature : Ta[°C] 75 Ambient Temperature:Ta[℃] Figure 10. Switch Fall Time vs Ambient Temperature Figure 9. Switch Rise Delay Time vs Ambient Temperature www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 5/17 TSZ02201-0E3E0H300260-1-2 21.Aug.2014 Rev.002 Datasheet BD6524HFV Typical Performance Curves - continued 3.0 UVLOUVLO Threshold Voltage : VUVLO [V] Threshold:V UVLO[V] Switch Delay Time : 2[us] tOFF2[μs] TurnFall OFF Time2:t OFF 3.5 3.0 2.5 2.0 1.5 1.0 0.5 From above: VIN=3.0V, 4.0V, 5.0V, 5.5V 2.5 VIN Increasing VIN Decreasing 2.0 1.5 1.0 0.5 0.0 0.0 -25 0 25 50 -25 75 0 25 50 75 Ambient : Ta[°C] AmbientTemperature Temperature:Ta[℃] Ambient Temperature : Ta[°C] Ambient Temperature:Ta[℃] Figure 11. Switch Fall Delay Time vs Ambient Temperature Figure 12. UVLO Threshold Voltage vs Ambient Temperature 50 250 Operating Current : IDD[μA] Operating Current:IDD[uA] Discharge Resistance:RDISC[Ω] 45 200 150 100 From above: VIN=3.0V, 5.0V, 5.5V 50 40 35 30 25 20 15 10 Ta=25°C 5 0 0 -25 0 25 50 3.0 75 3.5 4.0 4.5 5.0 Ambient Temperature:Ta[℃] Temperature : Ta[°C] Input Voltage:VIN[V] Figure 13. Discharge Resistance vs Ambient Temperature Figure 14. Operating Current vs Input Voltage www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 6/17 5.5 TSZ02201-0E3E0H300260-1-2 21.Aug.2014 Rev.002 Datasheet BD6524HFV Typical Performance Curves - continued 350 2.0 Switch ON-Resistance : RON[mΩ] ON Resistance:R ON[m Ω] EN Input Voltage:VEN[V] 2.5 VENH 1.5 VENL 1.0 Ta=25°C 0.5 0.0 250 200 150 100 Ta=25°C 50 0 3 3.5 4 4.5 5 5.5 3.0 3.5 4.0 4.5 5.0 Input Voltage:VIN[V] Input Voltage:VIN[V] Figure 15. EN Input Voltage vs Input Voltage Figure 16. Switch ON-Resistance vs Input Voltage 5.5 3.5 0.9 Ta=25°C 0.7 0.6 tON2 0.5 0.4 tON1 0.3 Ta=25°C 3.0 Switch Fall Time : TOFF[μs] Turn Off Time:T OFF[us] 0.8 Switch Rise Time : tON[ms] Turn On Time:T ON[ms] 300 0.2 2.5 tOFF2 2.0 1.5 1.0 tOFF1 0.5 0.1 0.0 0.0 3 4 5 5.5 3 4 5 Input Voltage:VIN[V] Input Voltage:VIN[V] Figure 17. Switch Rise Time vs Input Voltage Figure 18. Switch Fall Time vs Input Voltage www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 7/17 5.5 TSZ02201-0E3E0H300260-1-2 21.Aug.2014 Rev.002 Datasheet BD6524HFV Typical Performance Curves - continued Discharge : RDISC [Ω] Discharge Resistance Resistance:R DISC[Ω] 250 200 150 100 Ta=25°C 50 0 3 3.5 4 4.5 5 5.5 Input Voltage:VIN[V] Figure 19. Discharge Resistance vs Input Voltage www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 8/17 TSZ02201-0E3E0H300260-1-2 21.Aug.2014 Rev.002 Datasheet BD6524HFV Typical Wave Forms RL=10Ω, CL=10μF VIN = 5V EN (1V/div) EN (1V/div) RL=10Ω, CL=10μF VIN = 5V 1.05ms VOUT (1V/div) VOUT (1V/div) 0.42ms Time (200μs/div) Time (500μs/div) Figure 20. Switch Rise Time Figure 21. Switch Fall Time EN (1V/div) EN (1V/div) RL=10Ω, CL=10μF VIN = 3V RL=10Ω, CL=10μF VIN = 3V 0.74ms VOUT (1V/div) VOUT (1V/div) 1.10ms Time (200μs/div) Time (500μs/div) Figure 22. Switch Rise Time www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 Figure 23. Switch Fall Time 9/17 TSZ02201-0E3E0H300260-1-2 21.Aug.2014 Rev.002 Datasheet BD6524HFV EN (5V/div) EN (5V/div) Typical Wave Forms – continued VIN = 5V CL= 10μF VIN = 3V CL = 4.7μF CL= 4.7μF Irush (50mA/div) Irush (50mA/div) CL= 10μF CL = 1μF CL = 1μF Time (100μs/div) Time (100μs/div) Figure 24. Inrush Current Figure 25. Inrush Current CL=1µF VIN = 3V VIN (1V/div) VOUT (1V/div) VOUT (1V/div) VIN (1V/div) CL=10µF VIN = 3V 50ms 5ms Time (20ms/div) Time (2ms/div) Figure 26. UVLO Figure 27. UVLO www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 10/17 TSZ02201-0E3E0H300260-1-2 21.Aug.2014 Rev.002 Datasheet BD6524HFV Typical Application Circuit IN OUT IN OUT EN GND LOAD 0.1μF to 1μF EN Functional Description 1. Input / Output The IN and OUT pins are connected to the drain and the source of the N-MOS switch respectively. The IN pin is also used as power supply input to the internal control circuit. When EN input is set to High level and the switch is turned ON, the IN and OUT pins are connected by a 200mΩ switch. Under normal conditions, current flows from IN to OUT. If voltage at pin OUT pin is higher than pin IN, current flows from OUT to IN since the switch is bidirectional. There is no parasitic diode between the drain and the source, so it is possible to prevent current from flowing reversely from OUT pin to IN pin when the switch is disabled. 2. Discharge Circuit When the switch between the IN and the OUT is turned OFF, the 200Ω(Typ) discharge switch between OUT and GND turns on. By turning on this switch, electric charge at capacitive load is discharged. 3. Under Voltage Lockout (UVLO) The UVLO circuit monitors the voltage of the IN pin when the EN input is active. UVLO circuit prevents the switch from turning ON until the IN exceeds 2.2V (Typ). If the IN drops below 2.1V (Typ) while the switch turns on, then UVLO shuts off the switch. While the switch between the IN pin and OUT pin is OFF due to UVLO operations, the switch of the discharge circuit turns ON. However, when the voltage of IN declines tremendously, then the OUT pin becomes Hi-Z. 2.1V(Typ.) (Typ) VIN VIN 2.2V(Typ.) (Typ) VEN VEN VOUT VOUT 放電回路 Discharge Circuit ON OFF ON OFF ON OFF Figure 28. Operation Timing www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 11/17 TSZ02201-0E3E0H300260-1-2 21.Aug.2014 Rev.002 Datasheet BD6524HFV Power Dissipation (HVSOF6 package) 900 Power Dissipation : Pd[mW] POWER DISSIPATION : Pd [mW] 800 700 600 500 400 300 200 100 0 0 25 50 75 100 125 150 Ambient TEMPERATURE Temperature : Ta[°C] AMBIENT : Ta [℃] 70mm x 70mm x 1.6mm Glass Epoxy Board Figure 29. Power dissipation curve (Pd-Ta Curve) I/O Equivalence Circuit IN IN EN www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 OUT 12/17 TSZ02201-0E3E0H300260-1-2 21.Aug.2014 Rev.002 Datasheet BD6524HFV Operational Notes 1. Reverse Connection of Power Supply Connecting the power supply in reverse polarity can damage the IC. Take precautions against reverse polarity when connecting the power supply, such as mounting an external diode between the power supply and the IC’s power supply pins. 2. Power Supply Lines Design the PCB layout pattern to provide low impedance supply lines. Separate the ground and supply lines of the digital and analog blocks to prevent noise in the ground and supply lines of the digital block from affecting the analog block. Furthermore, connect a capacitor to ground at all power supply pins. Consider the effect of temperature and aging on the capacitance value when using electrolytic capacitors. 3. Ground Voltage Ensure that no pins are at a voltage below that of the ground pin at any time, even during transient condition. 4. Ground Wiring Pattern When using both small-signal and large-current ground traces, the two ground traces should be routed separately but connected to a single ground at the reference point of the application board to avoid fluctuations in the small-signal ground caused by large currents. Also ensure that the ground traces of external components do not cause variations on the ground voltage. The ground lines must be as short and thick as possible to reduce line impedance. 5. Thermal Consideration Should by any chance the power dissipation rating be exceeded the rise in temperature of the chip may result in deterioration of the properties of the chip. The absolute maximum rating of the Pd stated in this specification is when the IC is mounted on a 70mm x 70mm x 1.6mm glass epoxy board. In case of exceeding this absolute maximum rating, increase the board size and copper area to prevent exceeding the Pd rating. 6. Recommended Operating Conditions These conditions represent a range within which the expected characteristics of the IC can be approximately obtained. The electrical characteristics are guaranteed under the conditions of each parameter. 7. In rush Current 8. Operation Under Strong Electromagnetic Field Operating the IC in the presence of a strong electromagnetic field may cause the IC to malfunction. 9. Testing on Application Boards When testing the IC on an application board, connecting a capacitor directly to a low-impedance output pin may subject the IC to stress. Always discharge capacitors completely after each process or step. The IC’s power supply should always be turned off completely before connecting or removing it from the test setup during the inspection process. To prevent damage from static discharge, ground the IC during assembly and use similar precautions during transport and storage. When power is first supplied to the IC, it is possible that the internal logic may be unstable and inrush current may flow instantaneously due to the internal powering sequence and delays, especially if the IC has more than one power supply. Therefore, give special consideration to power coupling capacitance, power wiring, width of ground wiring, and routing of connections. 10. Inter-pin Short and Mounting Errors Ensure that the direction and position are correct when mounting the IC on the PCB. Incorrect mounting may result in damaging the IC. Avoid nearby pins being shorted to each other especially to ground, power supply and output pin. Inter-pin shorts could be due to many reasons such as metal particles, water droplets (in very humid environment) and unintentional solder bridge deposited in between pins during assembly to name a few. www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 13/17 TSZ02201-0E3E0H300260-1-2 21.Aug.2014 Rev.002 Datasheet BD6524HFV Operational Notes - continued 11. Unused Input Pins Input pins of an IC are often connected to the gate of a MOS transistor. The gate has extremely high impedance and extremely low capacitance. If left unconnected, the electric field from the outside can easily charge it. The small charge acquired in this way is enough to produce a significant effect on the conduction through the transistor and cause unexpected operation of the IC. So unless otherwise specified, unused input pins should be connected to the power supply or ground line. 12. Regarding the Input Pin of the IC This monolithic IC contains P+ isolation and P substrate layers between adjacent elements in order to keep them isolated. P-N junctions are formed at the intersection of the P layers with the N layers of other elements, creating a parasitic diode or transistor. For example (refer to figure below): When GND > Pin A and GND > Pin B, the P-N junction operates as a parasitic diode. When GND > Pin B, the P-N junction operates as a parasitic transistor. Parasitic diodes inevitably occur in the structure of the IC. The operation of parasitic diodes can result in mutual interference among circuits, operational faults, or physical damage. Therefore, conditions that cause these diodes to operate, such as applying a voltage lower than the GND voltage to an input pin (and thus to the P substrate) should be avoided. Resistor Transistor (NPN) Pin A Pin B C Pin A N P+ N P N P+ N Parasitic Elements N P+ GND E N P N P+ B N C E Parasitic Elements P Substrate P Substrate Parasitic Elements Pin B B Parasitic Elements GND GND Figure 30. Example of monolithic IC structure N Region close-by GND 13. Ceramic Capacitor When using a ceramic capacitor, determine the dielectric constant considering the change of capacitance with temperature and the decrease in nominal capacitance due to DC bias and others. www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 14/17 TSZ02201-0E3E0H300260-1-2 21.Aug.2014 Rev.002 Datasheet BD6524HFV Ordering Information B D 6 5 2 4 Part Number H F V Package HFV: HVSOF6 - TR Packaging and forming specification TR: Embossed tape and reel Marking Diagram HVSOF6 (TOP VIEW) Part Number Marking BD LOT Number 1PIN MARK www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 15/17 TSZ02201-0E3E0H300260-1-2 21.Aug.2014 Rev.002 Datasheet BD6524HFV Physical Dimension, Tape and Reel Information Package Name www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 HVSOF6 16/17 TSZ02201-0E3E0H300260-1-2 21.Aug.2014 Rev.002 Datasheet BD6524HFV Revision History Date 11.Mar.2013 21.Aug.2014 Revision 001 002 Changes New Release Applied the ROHM Standard Style and improved understandability. www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 17/17 TSZ02201-0E3E0H300260-1-2 21.Aug.2014 Rev.002 Datasheet Notice Precaution on using ROHM Products 1. Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment, OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you (Note 1) , transport intend to use our Products in devices requiring extremely high reliability (such as medical equipment equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific Applications. (Note1) Medical Equipment Classification of the Specific Applications JAPAN USA EU CHINA CLASSⅢ CLASSⅡb CLASSⅢ CLASSⅢ CLASSⅣ CLASSⅢ 2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which a failure or malfunction of our Products may cause. The following are examples of safety measures: [a] Installation of protection circuits or other protective devices to improve system safety [b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. Our Products are designed and manufactured for use under standard conditions and not under any special or extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our Products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents [b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust [c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves [e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items [f] Sealing or coating our Products with resin or other coating materials [g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] Use of the Products in places subject to dew condensation 4. The Products are not subject to radiation-proof design. 5. Please verify and confirm characteristics of the final or mounted products in using the Products. 6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied, confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect product performance and reliability. 7. De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual ambient temperature. 8. Confirm that operation temperature is within the specified range described in the product specification. 9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in this document. Precaution for Mounting / Circuit board design 1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product performance and reliability. 2. In principle, the reflow soldering method must be used; if flow soldering method is preferred, please consult with the ROHM representative in advance. For details, please refer to ROHM Mounting specification Notice – GE © 2013 ROHM Co., Ltd. All rights reserved. Rev.002 Datasheet Precautions Regarding Application Examples and External Circuits 1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the characteristics of the Products and external components, including transient characteristics, as well as static characteristics. 2. You agree that application notes, reference designs, and associated data and information contained in this document are presented only as guidance for Products use. Therefore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. Precaution for Electrostatic This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron, isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control). Precaution for Storage / Transportation 1. Product performance and soldered connections may deteriorate if the Products are stored in the places where: [a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [b] the temperature or humidity exceeds those recommended by ROHM [c] the Products are exposed to direct sunshine or condensation [d] the Products are exposed to high Electrostatic 2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is exceeding the recommended storage time period. 3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of which storage time is exceeding the recommended storage time period. Precaution for Product Label QR code printed on ROHM Products label is for ROHM’s internal use only. Precaution for Disposition When disposing Products please dispose them properly using an authorized industry waste company. Precaution for Foreign Exchange and Foreign Trade act Since our Products might fall under controlled goods prescribed by the applicable foreign exchange and foreign trade act, please consult with ROHM representative in case of export. Precaution Regarding Intellectual Property Rights 1. All information and data including but not limited to application example contained in this document is for reference only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. ROHM shall not be in any way responsible or liable for infringement of any intellectual property rights or other damages arising from use of such information or data.: 2. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any third parties with respect to the information contained in this document. Other Precaution 1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM. 2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of ROHM. 3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the Products or this document for any military purposes, including but not limited to, the development of mass-destruction weapons. 4. The proper names of companies or products described in this document are trademarks or registered trademarks of ROHM, its affiliated companies or third parties. Notice – GE © 2013 ROHM Co., Ltd. All rights reserved. Rev.002 Datasheet General Precaution 1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents. ROHM shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny ROHM’s Products against warning, caution or note contained in this document. 2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s representative. 3. The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccur acy or errors of or concerning such information. Notice – WE © 2014 ROHM Co., Ltd. All rights reserved. Rev.001 Datasheet BD6524HFV - Web Page Buy Distribution Inventory Part Number Package Unit Quantity Minimum Package Quantity Packing Type Constitution Materials List RoHS BD6524HFV HVSOF6 3000 3000 Taping inquiry Yes