LINER LT1963 Dual 750ma/250ma low dropout, low noise, micropower linear regulator Datasheet

LT3030
Dual 750mA/250mA
Low Dropout, Low Noise,
Micropower Linear Regulator
Description
Features
n
n
n
n
n
n
n
n
n
n
n
n
n
n
Output Current: 750mA/250mA
Low Dropout Voltage: 300mV
Low Noise: 20μVRMS (10Hz to 100kHz)
Low Quiescent Current: 120μA/75μA
Wide Input Voltage Range: 1.8V to 20V
Adjustable Output: 1.220V Reference Voltage
Shutdown Quiescent Current: <1μA
Stable with 10µF/3.3µF Minimum Output Capacitor
Stable with Ceramic, Tantalum or Aluminum
Electrolytic Capacitors
Precision Threshold for Shutdown Logic or UVLO Function
PWRGD Flag for each Output
Reverse Battery and Reverse Output-to-Input
Protection
Current Limit with Foldback and Thermal Shutdown
Thermally Enhanced 20-Lead TSSOP and
28-Lead (4mm × 5mm) QFN Packages
The LT®3030 is a dual, micropower, low noise, low dropout
linear regulator. The device operates with either common
or independent input supplies for each channel, over a
1.8V to 20V input voltage range. Output 1/Output 2 supply
750mA/250mA respectively with a typical dropout voltage
of 300mV. With an external 10nF bypass capacitor, output
noise is only 20μVRMS over a 10Hz to 100kHz bandwidth.
Designed for use in battery-powered systems, the low
120μA/75μA quiescent current makes it an ideal choice.
In shutdown, quiescent current drops to less than 1μA.
Shutdown control is independent for each channel and
its precision logic threshold allows for voltage lockout
functionality. The LT3030 includes a PWRGD flag for each
channel to indicate output regulation.
The LT3030 optimizes stability and transient response with
low ESR ceramic output capacitors, requiring a minimum
of only 10μF/3.3μF.
Applications
n
n
n
n
n
Internal circuitry provides reverse-battery protection,
reverse-current protection, current limiting with foldback
and thermal shutdown with hysteresis. The adjustable
output voltage device has a 1.220V reference voltage.
The LT3030 is offered in the thermally enhanced 20-lead
TSSOP and 28-lead, low profile (4mm × 5mm × 0.75mm)
QFN packages.
General Purpose Linear Regulator
Battery-Powered Systems
Microprocessor Core/Logic Supplies
Post Regulator for Switching Supplies
Tracking/Sequencing Power Supplies
L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks and
ThinSOT is a trademark of Linear Technology Corporation. All other trademarks are the property
of their respective owners.
Typical Application
2.5VIN to 1.8V/1.5V Application
IN1
3.3µF
IN2
1M
OUT1
10nF
LT3030
SHDN1
BYP1
SHDN2
ADJ1
10µF
113k
1%
VOUT1
1.8V
750mA
237k
1%
1M
PWRGD1
PWRGD2
OUT2
10nF
BYP2
GND
ADJ2
3030 TA01a
3.3µF
54.9k
1%
VOUT2
1.5V
250mA
400
350
300
OUT2
250
200
OUT1
150
100
50
0
237k
1%
TJ = 25°C
450
DROPOUT VOLTAGE (mV)
VIN
2.5V
Dropout Voltage vs Load Current
500
0
75 150 225 300 375 450 525 600 675 750
OUTPUT CURRENT (mA)
3030 TA01b
3030f
For more information www.linear.com/3030
1
LT3030
Absolute Maximum Ratings
(Note 1)
IN1, IN2 Pin Voltage.................................................±22V
OUT1, OUT2 Pin Voltage..........................................±22V
Input-to-Output Differential Voltage.........................±22V
ADJ1, ADJ2 Pin Voltage.............................................±9V
BYP1, BYP2 Pin Voltage.........................................±0.6V
SHDN1, SHDN2 Pin Voltage.....................................±22V
PWRGD1, PWRGD2 Pin Voltage.....................22V, –0.3V
Output Short-Circuit Duration........................... Indefinite
Operating Junction Temperature (Notes 2, 12)
E-/I-Grade........................................... –40°C to 125°C
H-Grade.............................................. –40°C to 150°C
MP-Grade........................................... –55°C to 150°C
Storage Temperature Range
QFN/TSSOP Package.............................. –65°C to 150°C
Lead Temperature (Soldering, 10 sec)
(TSSOP Only)......................................................... 300°C
Pin Configuration
SHDN1
GND
GND
GND
ADJ1
BYP1
TOP VIEW
TOP VIEW
28 27 26 25 24 23
ADJ1
1
20 SHDN1
BYP1
2
19 PWRGD1
OUT1
3
18 IN1
17 IN1
OUT1 1
22 PWRGD1
OUT1 2
21 IN1
GND 3
20 IN1
OUT1
4
GND 4
19 GND
GND
5
18 GND
GND
6
17 IN2
OUT2
7
14 IN2
OUT2 7
16 IN2
OUT2
8
13 IN2
OUT2 8
15 PWRGD2
BYP2
9
12 PWRGD2
GND
29
GND 5
GND 6
ADJ2 10
SHDN2
GND
GND
GND
ADJ2
BYP2
9 10 11 12 13 14
GND
21
16 GND
15 GND
11 SHDN2
FE PACKAGE
20-LEAD PLASTIC TSSOP
UFD PACKAGE
28-LEAD (4mm × 5mm) PLASTIC QFN
TJMAX = 125°C, θJA = 33°C/W, , θJC = 3.4°C/W
EXPOSED PAD (PIN 29) IS GND, MUST BE SOLDERED TO PCB
TJMAX = 150°C, θJA = 28°C/W, , θJC = 10°C/W
EXPOSED PAD (PIN 21) IS GND, MUST BE SOLDERED TO PCB
Order Information
LEAD FREE FINISH
TAPE AND REEL
PART MARKING*
PACKAGE DESCRIPTION
TEMPERATURE RANGE
LT3030EUFD#PBF
LT3030EUFD#TRPBF
3030
28-Lead (4mm × 5mm) Plastic QFN
–40°C to 125°C
LT3030IUFD#PBF
LT3030IUFD#TRPBF
3030
28-Lead (4mm × 5mm) Plastic QFN
–40°C to 125°C
LT3030EFE#PBF
LT3030EFE#TRPBF
LT3030FE
20-Lead Plastic TSSOP
–40°C to 125°C
LT3030IFE#PBF
LT3030IFE#TRPBF
LT3030FE
20-Lead Plastic TSSOP
–40°C to 125°C
LT3030HFE#PBF
LT3030HFE#TRPBF
LT3030FE
20-Lead Plastic TSSOP
–40°C to 150°C
LT3030MPFE#PBF
LT3030MPFE#TRPBF
LT3030FE
20-Lead Plastic TSSOP
–55°C to 150°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/
3030f
2
For more information www.linear.com/3030
LT3030
Electrical Characteristics
The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C (Note 2).
PARAMETER
CONDITIONS
Minimum Input Voltage (Notes 3, 11)
Output 1, ILOAD = 750mA
Output 2, ILOAD = 250mA
l
l
ADJ1, ADJ2 Pin Voltage (Notes 3, 4)
VIN = 2V, ILOAD = 1mA
Output 1, 2.2V < VIN1 < 20V, 1mA < ILOAD < 750mA
Output 2, 2.2V < VIN2 < 20V, 1mA < ILOAD < 250mA
l
l
Line Regulation (Note 3)
∆VIN = 2V to 20V, ILOAD = 1mA
l
Load Regulation (Note 3)
Output 1, VIN1 = 2.2V, ∆ILOAD = 1mA to 750mA
VIN1 = 2.2V, ∆ILOAD = 1mA to 750mA
l
Output 2, VIN2 = 2.2V, ∆ILOAD = 1mA to 250mA
VIN2 = 2.2V, ∆ILOAD = 1mA to 250mA
l
ILOAD = 10mA
ILOAD = 10mA
l
ILOAD = 100mA
ILOAD = 100mA
l
ILOAD = 500mA
ILOAD = 500mA
l
ILOAD = 750mA
ILOAD = 750mA
l
ILOAD = 10mA
ILOAD = 10mA
l
ILOAD = 50mA
ILOAD = 50mA
l
ILOAD = 100mA
ILOAD = 100mA
l
ILOAD = 250mA
ILOAD = 250mA
l
GND Pin Current (Output 1)
VIN1 = VOUT1(NOMINAL)
(Notes 5, 7)
ILOAD = 0mA
ILOAD = 10mA
ILOAD = 100mA
ILOAD = 500mA
ILOAD = 750mA
GND Pin Current (Output 2)
VIN2 = VOUT2(NOMINAL)
(Notes 5, 7)
ILOAD = 0mA
ILOAD = 10mA
ILOAD = 50mA
ILOAD = 100mA
ILOAD = 250mA
Output Voltage Noise
COUT = 10μF, CBYP = 10nF, ILOAD = Full Current (Note 13)
BW = 10Hz to 100kHz
Dropout Voltage (Output 1)
VIN1 = VOUT1(NOMINAL)
(Notes 5, 6, 11)
Dropout Voltage (Output 2)
VIN2 = VOUT2(NOMINAL)
(Notes 5, 6, 11)
MIN
TYP
MAX
1.7
1.7
2.2
2.2
V
V
1.220
1.220
1.220
1.232
1.244
1.244
V
V
V
0.5
5
mV
2
6
10
mV
mV
2
6
10
mV
mV
0.13
0.20
0.28
V
V
0.17
0.23
0.33
V
V
0.27
0.32
0.43
V
V
0.3
0.36
0.48
V
V
0.14
0.20
0.28
V
V
0.18
0.24
0.32
V
V
0.22
0.28
0.38
V
V
0.3
0.36
0.48
V
V
l
l
l
l
l
120
420
2
9
15
300
800
3.8
17
27
μA
μA
mA
mA
mA
l
l
l
l
l
75
330
1
1.8
5
200
600
1.8
3.4
9
μA
μA
mA
mA
mA
1.208
1.196
1.196
20
ADJ1/ADJ2 Pin Bias Current (Notes 3, 8)
Shutdown Threshold
VOUT = Off to On
VOUT = On to Off
Hysteresis (Note 2)
l
l
SHDN1/SHDN2 Pin Current (Note 10)
VSHDN1, VSHDN2 = 0V
VSHDN1, VSHDN2 = 20V
l
l
1.09
0.5
Quiescent Current in Shutdown (per Channel) VIN = 20V, VSHDN1 = 0V, VSHDN2 = 0V
PWRGD Trip Point
% of Nominal Output Voltage, Output Rising
l
PWRGD Trip Point Hysteresis (Note 2)
% of Nominal Output Voltage, Output Falling
PWRGD Output Low Voltage
IPWRGD = 100μA
l
PWRGD Leakage Current
VSHDN = 0V, VPWRGD = 20V
l
86
UNITS
μVRMS
30
100
nA
1.21
0.83
0.38
1.33
V
V
V
0
0.85
0.5
3
μA
μA
0.3
2
μA
90
94
%
150
mV
1
μA
1.6
15
%
3030f
For more information www.linear.com/3030
3
LT3030
Electrical Characteristics
The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C (Note 2).
PARAMETER
CONDITIONS
Ripple Rejection
VIN = 2.72V (Avg), VRIPPLE = 0.5VP-P,
fRIPPLE = 120Hz, ILOAD = Full Current (Note 13)
MIN
TYP
50
60
dB
50
dB
VIN = VOUT(NOMINAL) + 1V, VRIPPLE = 50mVRMS
fRIPPLE = 1MHz, ILOAD = Full Current (Note 13)
MAX
UNITS
Output 1, VIN1 = 6V, VOUT1 = 0V
VIN1 = 2.2V, ∆VOUT1 = –0.1V
l
l
1.1
800
1.4
1.7
A
mA
Output 2, VIN2 = 6V, VOUT2 = 0V
VIN2 = 2.2V, ∆VOUT2 = –0.1V
l
l
350
270
420
490
mA
mA
Input Reverse Leakage Current
VIN = –20V, VOUT = 0V
l
1
mA
Reverse Output Current
VOUT = 1.220V, VIN = 0V
0.5
10
μA
Current Limit (Note 9)
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: The LT3030 is tested and specified under pulse load conditions
such that TJ ≈ TA. The LT3030E is 100% tested at TA = 25°C and
performance is guaranteed from 0°C to 125°C. Performance of the
LT3030E over the full –40°C to 125°C operating junction temperature
range is assured by design, characterization and correlation with statistical
process controls. The LT3030I is guaranteed over the full –40°C to 125°C
operating junction temperature range. The LT3030MP is 100% tested and
guaranteed over the –55°C to 150°C operating junction temperature range.
The LT3030H is tested at 150°C operating junction temperature. High
junction temperatures degrade operating lifetimes. Operating lifetime is
derated at junction temperatures greater than 125°C.
Note 3: The LT3030 is tested and specified for these conditions with the
ADJ1/ADJ2 pin connected to the corresponding OUT1/OUT2 pin.
Note 4: Maximum junction temperature limits operating conditions. The
regulated output voltage specification does not apply for all possible
combinations of input voltage and output current. When operating at
maximum input voltage, limit the output current range. When operating at
maximum output current, limit the input voltage range.
Note 5: To satisfy minimum input voltage requirements, the LT3030 is
tested and specified for these conditions with an external resistor divider
(two 243k resistors) for an output voltage of 2.447V. The external resistor
divider adds 5μA of DC load on the output.
Note 6: Dropout voltage is the minimum input to output voltage differential
needed to maintain regulation at a specified output current. In dropout, the
output voltage equals: VIN – VDROPOUT.
Note 7: GND pin current is tested with VIN = 2.447V and a current source
load. This means the device is tested while operating in its dropout region
or at the minimum input voltage specification. This is the worst-case
GND pin current. The GND pin current decreases slightly at higher input
voltages. Total GND pin current equals the sum of output 1 and output 2
GND pin currents.
Note 8: ADJ1/ADJ2 pin bias current flows into the pin.
Note 9: The LT3030 contains current limit foldback circuitry. See the
Typical Performance Characteristics section for current limit as a function
of the VIN – VOUT differential voltage.
Note 10: SHDN1 and SHDN2 pin current flows into the pin.
Note 11: The LT3030 minimum input voltage specification limits dropout
voltage under some output voltage/load conditions. See the curve of
Minimum Input Voltage in the Typical Performance Characteristics section.
Note 12: The LT3030 includes overtemperature protection that is intended
to protect the device during momentary overload conditions. Junction
temperature exceeds the maximum operating junction temperature when
overtemperature protection is active. Continuous operation above the
specified maximum operating junction temperature may impair device
reliability.
Note 13: The Full Current for ILOAD is 750mA and 250mA for Output 1 and
Output 2 respectively.
3030f
4
For more information www.linear.com/3030
LT3030
Typical Performance Characteristics
450
TJ = 150°C
TJ = 25°C
250
200
TJ = –55°C
150
100
50
0
0
TJ = 25°C
300
250
200
150
100
50
0
75 150 225 300 375 450 525 600 675 750
OUTPUT CURRENT (mA)
TJ = 150°C
350
0
3030 G01
450
450
TJ = 150°C
TJ = 125°C
TJ = 25°C
250
200
TJ = –55°C
150
100
50
0
0
GUARANTEED DROPOUT VOLTAGE (mV)
DROPOUT VOLTAGE (mV)
500
300
25 50 75 100 125 150 175 200 225 250
OUTPUT CURRENT (mA)
= TEST POINTS
150
100
500
250
200
150
100
50
400
350
300
250
200
150
100
50
0
0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
25 50 75 100 125 150 175 200 225 250
OUTPUT CURRENT (mA)
3030 G05
3030 G06
ADJ1/ADJ2 Pin Voltage
VIN1 = VIN2 = 6V
RL1 = RL2 = 243k; IL1 = IL2 = 5µA
1.238
OUTPUT 1
VSHDN1 = VIN1
OUTPUT 2
VSHDN2 = VIN2
Quiescent Current
300
IL1 = IL2 = 1mA
1.226
1.220
3030 G07
TJ = 25°C
RL1 = RL2 = 243k; IL1 = IL2 = 5µA
VOUT1 = VOUT2 = 1.220V
250
1.232
ADJ2
ADJ1
1.214
1.208
200
150
OUTPUT 1, VSHDN1 = VIN1
100
OUTPUT 2, VSHDN2 = VIN2
50
1.202
0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
IL = 250mA
IL = 175mA
IL = 100mA
IL = 50mA
IL = 10mA
IL = 1mA
450
300
1.244
100
50
150
3030 G03
TJ = 150°C
TJ = 25°C
350
0
ADJ PIN VOLTAGE (V)
QUIESCENT CURRENT (µA)
200
200
OUT2 Dropout Voltage
vs Temperature
400
Quiescent Current
250
250
0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
75 150 225 300 375 450 525 600 675 750
OUTPUT CURRENT (mA)
3030 G04
300
300
OUT2 Guaranteed Dropout
Voltage
500
350
350
3030 G02
OUT2 Typical Dropout Voltage
400
400
50
DROPOUT VOLTAGE (mV)
300
400
IL = 750mA
IL = 500mA
IL = 300mA
IL = 100mA
IL = 10mA
IL = 1mA
450
QUIESCENT CURRENT (µA)
350
500
= TEST POINTS
DROPOUT VOLTAGE (mV)
500
450
GUARANTEED DROPOUT VOLTAGE (mV)
DROPOUT VOLTAGE (mV)
500
TJ = 125°C
OUT1 Dropout Voltage
vs Temperature
OUT1 Guaranteed Dropout
Voltage
OUT1 Typical Dropout Voltage
400
TJ = 25°C, unless otherwise noted.
1.196
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
3030 G08
0
OUTPUT 1; VSHDN1 = 0V
OUTPUT 2; VSHDN2 = 0V
0
2
4
6 8 10 12 14 16 18 20
INPUT VOLTAGE (V)
3030 G09
3030f
For more information www.linear.com/3030
5
LT3030
Typical Performance Characteristics
Quiescent Current in Shutdown
(per Output)
0.7
0.6
0.5
0.4
0.3
0.2
IL1 = 100mA
1.5
0
2
4
1.2
0.9
0.6
0
6 8 10 12 14 16 18 20
INPUT VOLTAGE (V)
IL1 = 10mA
0
1
2
IL1 = 1mA
3
4
5
6
INPUT VOLTAGE (V)
7
GND PIN CURRENT (mA)
GND PIN CURRENT (mA)
15
12
9
6
3
IL1 = 25mA
0.4
IL1 = 10mA
IL1 = 1mA
SHDN PIN THRESHOLD (V)
GND PIN CURRENT (mA)
1.2
3
2
0
1
2
6
3
4
5
INPUT VOLTAGE (V)
7
8
0
25 50 75 100 125 150 175 200 225 250
OUTPUT CURRENT (mA)
3030 G16
3
4
5
6
INPUT VOLTAGE (V)
7
1.0
8
9
TJ = 25°C
FOR VOUT2 = 1.220V
7
6
5
IL2 = 250mA
4
3
2
0
9
IL2 = 100mA
IL2 = 50mA
0
1
2
3
4
5
6
INPUT VOLTAGE (V)
7
TJ = 25°C
1.8
0.8
0.6
0.4
VIN = 2.2V
0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
3030 G17
9
SHDN1 or SHDN2 Pin Input
Current
2.0
ON TO OFF
8
3030 G15
OFF TO ON
0.2
1
2
1
1.4
TJ = 25°C
VIN2 = VOUT2(NOMINAL) + 1V
4
1
3030 G12
SHDN1 or SHDN2 Pin Threshold
5
0
3030 G14
OUT2 GND Pin Current
6
IL1 = 250mA
OUT2 GND Pin Current
0.6
0
75 150 225 300 375 450 525 600 675 750
OUTPUT CURRENT (mA)
7
IL1 = 500mA
6
8
3030 G13
0
9
9
0.8
0.2
8
IL1 = 750mA
12
0
9
TJ = 25°C
FOR VOUT2 = 1.220V
1.0
18
9
8
GND PIN CURRENT (mA)
TJ = 25°C
VIN1 = VOUT1(NOMINAL) + 1V
0
15
OUT2 GND Pin Current
1.2
21
0
18
3030 G11
OUT1 GND Pin Current
24
21
3
3030 G10
27
TJ = 25°C
FOR VOUT1 = 1.220V
24
1.8
0.3
0.1
0
TJ = 25°C
FOR VOUT1 = 1.220V
2.1
GND PIN CURRENT (mA)
QUIESCENT CURRENT (µA)
0.8
OUT1 GND Pin Current
27
GND PIN CURRENT (mA)
TJ = 25°C
RL1 = RL2 = 243k; IL1 = IL2 = 5µA
VOUT1 = VOUT2 = 1.220V
VSHDN1 = VSHDN2 = 0V
0.9
OUT1 GND Pin Current
2.4
SHDN PIN INPUT CURRENT (µA)
1.0
TJ = 25°C, unless otherwise noted.
1.6
1.4
1.2
1.0
VIN = 2.2V
0.8
VIN = 20V
0.6
0.4
0.2
0
0
2
4
6 8 10 12 14 16 18 20
SHDN PIN VOLTAGE (V)
3030 G18
3030f
6
For more information www.linear.com/3030
LT3030
Typical Performance Characteristics
150
1.8
135
1.6
120
1.4
1.2
VIN = 2.2V,
VSHDN = 20V
1.0
0.8
0.6
0.4
VIN = 20V
VSHDN = 2.2V
0.2
105
90
75
60
45
30
15
0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
3030 G19
60
45
30
1.25
TJ = –55°C
1.00
TJ = 25°C
0.75
TJ = 125°C
0
0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
TJ = 150°C
0.48
0.48
0.42
0.42
TJ = 125°C
0.18
0.12
TJ = 150°C
0
2
4
2
4
1.0
0.8
0.6
6 8 10 12 14 16 18 20
INPUT VOLTAGE (V)
3030 G25
VIN = 18V
3030 G24
Reverse Current
5.0
VOUT = 0V
VIN = 6V
0.36
0.30
0.24
0.18
TJ = 25°C
VIN1 = VIN2 = 0V
VADJ1 = VOUT1
VADJ2 = VOUT2
4.5
VIN = 18V
4.0
3.5
3.0
2.5
IADJ1 OR IADJ2
2.0
1.5
1.0
0.5
0.06
0
1.2
0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
6 8 10 12 14 16 18 20
INPUT VOLTAGE (V)
0.12
0.06
0
CURRENT LIMIT (A)
CURRENT LIMIT (A)
0.54
TJ = 25°C
VIN = 6V
0.2
REVERSE CURRENT (mA)
VOUT = 0V
TJ = –55°C
VOUT = 0V
1.4
OUT2 Current Limit
0.60
0.24
86
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
3030 G23
OUT2 Current Limit
0.30
87
0.4
3030 G22
0.36
OUTPUT FALLING
88
1.6
0.25
15
0.54
89
1.8
0.50
0.60
OUTPUT RISING
90
OUT1 Current Limit
CURRENT LIMIT (A)
75
91
2.0
1.50
CURRENT LIMIT (A)
PWRGD OUTPUT LOW VOLTAGE (mV)
120
90
92
3030 G21
VOUT = 0V
1.75
105
93
OUT1 Current Limit
2.00
IPWRGD = 100µA
135
94
3030 G20
PWRGD1 or PWRGD2 Output Low
Voltage
150
PWRGD1 or PWRGD2 Trip Point
PWRGD TRIP POINT (% OF OUTPUT VOLTAGE)
ADJ1 or ADJ2 Pin Bias Current
2.0
ADJ PIN BIAS CURRENT (nA)
SHDN PIN INPUT CURRENT (µA)
SHDN1 or SHDN2 Pin Input
Current
TJ = 25°C, unless otherwise noted.
0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
0
IOUT1 OR IOUT2
0
1
2
5
3
4
6
7
OUTPUT VOLTAGE (V)
8
9
3030 G27
3030 G26
IADJ = FLOWS INTO ADJ PIN TO GND PIN
IOUT = FLOWS INTO OUT PIN TO IN PIN
3030f
For more information www.linear.com/3030
7
LT3030
Typical Performance Characteristics
Reverse Current
REVERSE CURRENT (µA)
400
VIN1 = VIN2 = 0V
VADJ1 = VOUT1 = 1.220V
VADJ2 = VOUT2 = 1.220V
350
300
250
200
IADJ1 OR IADJ2
IOUT1
150
100
IOUT2
50
0
–75 –25
0
25 50 75 100 125 150 175
TEMPERATURE (°C)
OUT1 Input Ripple Rejection
100
100
90
90
80
80
70
RIPPLE REJECTION (dB)
450
OUT1 Input Ripple Rejection
RIPPLE REJECTION (dB)
500
TJ = 25°C, unless otherwise noted.
COUT1 = 47µF
60
COUT1 = 22µF
50
40
COUT1 = 10µF
30
T = 25°C
20 I J = 750mA, C
L1
BYP1 = 0
10 VIN1 = VOUT1(NOMINAL) + 1V
+ 50mVRMS RIPPLE
0
100
10
1k
10k 100k
FREQUENCY (Hz)
CBYP1 = 1000pF
60
50
CBYP1 = 100pF
40
30
20
10
1M
CBYP1 = 10nF
70
0
10M
TJ = 25°C
IL1 = 750mA, COUT1 = 22µF
VIN1 = VOUT1(NOMINAL) + 1V
+ 50mVRMS RIPPLE
10
100
1k
10k 100k
FREQUENCY (Hz)
1M
3030 G29
3030 G28
10M
3030 G30
IADJ = FLOWS INTO ADJ PIN TO GND PIN
IOUT = FLOWS INTO OUT PIN TO IN PIN
OUT1 Input Ripple Rejection
OUT2 Input Ripple Rejection
OUT2 Input Ripple Rejection
100
90
90
90
80
80
70
60
50
40
30
20
10
VIN1 = VOUT1(NOMINAL) + 1.5V
+ 500mVP-P RIPPLE
f = 120Hz
IL1 = 750mA
COUT2 = 22µF
60
50
40
30
20
10
0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
80
COUT2 = 10µF
70
0
COUT2 = 3.3µF
TJ = 25°C
IL2 = 250mA, CBYP2 = 0
VIN2 = VOUT2(NOMINAL) + 1V
+ 50mVRMS RIPPLE
10
100
1k
10k 100k
FREQUENCY (Hz)
OUT2 Input Ripple Rejection
30
10M
0
TJ = 25°C
IL2 = 250mA, COUT2 = 10µF
VIN2 = VOUT2(NOMINAL) + 1V
+ 50mVRMS RIPPLE
10
100
1k
10k 100k
FREQUENCY (Hz)
1M
10M
3030 G33
Channel-to-Channel Isolation
CHANNEL-TO-CHANNEL ISOLATION (dB)
80
RIPPLE REJECTION (dB)
CBYP2 = 100pF
40
Channel-to-Channel Isolation
100
90
70
60
50
40
10
50
3030 G32
100
20
CBYP2 = 10nF
60
10
1M
CBYP2 = 1000pF
70
20
3030 G31
30
RIPPLE REJECTION (dB)
RIPPLE REJECTION (dB)
100
RIPPLE REJECTION (dB)
100
VIN2 = VOUT2(NOMINAL) + 1.5V
+ 500mVP-P RIPPLE
f = 120Hz
IL2 = 250mA
0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
3030 G34
90
80
70
60
CHANNEL 1
VOUT1
100mV/DIV
CHANNEL 2
VOUT2
100mV/DIV
50
40
30 GIVEN CHANNEL IS TESTED WITH
50mVRMS SIGNAL ON OPPOSING
20 CHANNEL,
BOTH CHANNELS
10 DELIVERING FULL CURRENT
TJ = 25°C
0
100
1M
10
1k
10k 100k
FREQUENCY (Hz)
3030 G36
10M
50µs/DIV
∆IL1 = 50mA TO 750mA
COUT1 = 10µF
COUT2 = 3.3µF
∆IL2 = 50mA TO 250mA
CBYP1 = CBYP2 = 0.01µF VIN = 6V, VOUT1 = VOUT2 = 5V
3030 G35
3030f
8
For more information www.linear.com/3030
LT3030
Typical Performance Characteristics
∆IL = 1mA TO FULL LOAD
4
6
4
2
0
–2
–4
∆VIN = 2V TO 20V
2
1
0
–1
–2
–6
–3
–8
–4
–10
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
–5
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
3030 G37
VOUT = 5V
CBYP = 100pF
VOUT = VADJ
0.1
CBYP = 0.01µF
0.1
140
1
10
FREQUENCY (Hz)
120
OUTPUT2
OUTPUT1
100
80
60 VOUT = 1.220V
40
OUTPUT1
100
0
10
0.1
1
10
FREQUENCY (kHz)
100
100
3030 G39
160
140
TJ = 25°C
COUT = 10µF
120
VOUT1 = 5V
CBYP1 = 0
100
80
VOUT1 = VADJ1
CBYP1 = 0
60
40
VOUT1 = VADJ1
1000
10000
VOUT1 = 5V
0
0.01
0.1
CBYP1 = 10nF
1
10
100
OUTPUT CURRENT (mA)
1000
3030 G42
3030 G41
Start-Up Time from Shutdown
CBYP = 0pF
OUT2 RMS Output Noise
vs Output Current (10Hz to 100kHz)
OUTPUT NOISE (µVRMS)
0.01
0.01
20
OUTPUT2
CBYP (pF)
3030 G40
140
0.1
OUT1 RMS Output Noise
vs Output Current (10Hz to 100kHz)
TJ = 25°C
COUT = 10µF
IL = FULL LOAD
fBW = 10Hz TO 100kHz
VOUT = 5V
20
CBYP = 1000pF
0.01
0.01
VOUT = 5V
VOUT = VADJ
OUTPUT NOISE (µVRMS)
160
TJ = 25°C
COUT = 10µF
IL = FULL LOAD
1
TJ = 25°C
COUT = 10µF
CBYP = 0
IL = FULL LOAD
1
RMS Output Noise vs Bypass
Capacitor
OUTPUT NOISE (µVRMS)
OUTPUT NOISE SPECTRAL DENSITY (µV/√Hz)
10
10
3030 G38
Output Noise Spectral Density
160
Output Noise Spectral Density
3
LINE REGULATION (mV)
LOAD REGULATION (mV)
8
OUT1 or OUT2 Line Regulation
5
OUTPUT NOISE SPECTRAL DENSITY (µV/√Hz)
OUT1 or OUT2 Load Regulation
10
TJ = 25°C, unless otherwise noted.
Start-Up Time from Shutdown
CBYP = 0.01µF
TJ = 25°C
COUT = 10µF
120
100
VOUT
1V/DIV
VOUT2 = 5V
CBYP2 = 0
80
VOUT2 = VADJ2
CBYP2 = 0
60
40
20
0
0.01
VOUT2 = 5V
SHDN
VOLTAGE
2V/DIV
SHDN
VOLTAGE
2V/DIV
CBYP2 = 10nF
VOUT2 = VADJ2
0.1
VOUT
1V/DIV
1
10
100
OUTPUT CURRENT (mA)
1000
3030 G45
3030 G44
VIN = 2.5V
CIN = 10µF
COUT = 10µF
1ms/DIV
IL = FULL LOAD
TJ = 25°C
VOUT = 1.5V
VIN = 2.5V
CIN = 10µF
COUT = 10µF
1ms/DIV
IL = FULL LOAD
TJ = 25°C
VOUT = 1.5V
3030 G43
3030f
For more information www.linear.com/3030
9
LT3030
Typical Performance Characteristics
10Hz to 100kHz Output Noise,
CBYP = 0pF
OUT1 or OUT2 Minimum Input
Voltage
2.50
MINIMUM INPUT VOLTAGE (V)
2.25
10Hz to 100kHz Output Noise,
CBYP = 100pF
VOUT1 = VOUT2 = 1.220V
2.00
IL = FULL LOAD
1.75
1.50
TJ = 25°C, unless otherwise noted.
VOUT
100µV/DIV
IL = 1mA
1.25
VOUT
100µV/DIV
1.00
0.75
0.50
COUT = 10µF
IL = FULL LOAD
VOUT = 5V
0.25
0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
1ms/DIV
3030 G47
COUT = 10µF
IL = FULL LOAD
VOUT = 5V
1ms/DIV
3030 G48
3030 G46
10Hz to 100kHz Output Noise,
CBYP = 1000pF
10Hz to 100kHz Output Noise,
CBYP = 0.01µF
OUT1 Transient Response
CBYP = 0pF
VOUT DEVIATION
200mV/DIV
VOUT
100µV/DIV
VOUT
100µV/DIV
LOAD CURRENT DEVIATION
500mA/DIV
COUT = 10µF
IL = FULL LOAD
VOUT = 5V
1ms/DIV
3030 G49
COUT = 10µF
IL = FULL LOAD
VOUT = 5V
OUT1 Transient Response
CBYP = 0.01µF
1ms/DIV
3030 G50
OUT2 Transient Response
CBYP = 0pF
200mV/DIV
50mV/DIV
100mA/DIV
500mA/DIV
LOAD CURRENT DEVIATION
100mA/DIV
3030 G53
3030 G52
20µs/DIV
IL = 100mA TO 750mA
TJ = 25°C
VOUT = 5V
VOUT DEVIATION
LOAD CURRENT DEVIATION
LOAD CURRENT DEVIATION
200µs/DIV
IL = 100mA TO 750mA
TJ = 25°C
VOUT = 5V
OUT2 Transient Response
CBYP = 0.01µF
VOUT DEVIATION
VOUT DEVIATION
50mV/DIV
VIN = 6V
CIN = 22µF
COUT = 22µF
3030 G51
VIN = 6V
CIN = 22µF
COUT = 22µF
VIN = 6V
CIN = 10µF
COUT = 10µF
200µs/DIV
IL = 100mA TO 250mA
TJ = 25°C
VOUT = 5V
3030 G54
VIN = 6V
CIN = 10µF
COUT = 10µF
20µs/DIV
IL = 100mA TO 250mA
TJ = 25°C
VOUT = 5V
3030f
10
For more information www.linear.com/3030
LT3030
Pin Functions
(QFN/TSSOP)
OUT1, OUT2 (Pins 1, 2, 7, 8/Pins 3, 4, 7, 8): Output. The
OUT1/OUT2 pins supply power to the loads. A minimum
10μF/3.3μF output capacitor prevents oscillations on
OUT1/OUT2. Applications with large output load transients
require larger values of output capacitance to limit peak
voltage transients. See the Applications Information section for more on output capacitance and on reverse output
characteristics.
GND (Pins 3, 4, 5, 6, 11, 12, 13, 18, 19, 24, 25, 26,
Exposed Pad Pin 29/Pins 5, 6, 15, 16, Exposed Pad Pin
21): Ground. The exposed pad (backside) of the QFN and
TSSOP packages is an electrical connection to GND. To
ensure proper electrical and thermal performance, solder the exposed pad to the PCB ground and tie directly
to GND pins. Connect the bottom of the output voltage
setting resistor divider directly to GND for optimum load
regulation performance.
IN1, IN2 (Pins 20, 21, 16, 17/Pins 17, 18, 13, 14): Input. The IN1/IN2 pins supply power to each channel. The
LT3030 requires a bypass capacitor at the IN1/IN2 pins
if located more than six inches away from the main input
filter capacitor. Include a bypass capacitor in batterypowered circuits, as a battery’s output impedance rises
with frequency. A bypass capacitor in the range of 1μF to
10μF suffices. The LT3030’s design withstands reverse
voltages on the IN pins with respect to ground and the
OUT pins. In the case of a reversed input, which occurs
if a battery is plugged in backwards, the LT3030 acts as
if a diode is in series with its input. No reverse current
flows into the LT3030 and no reverse voltage appears at
the load. The device protects itself and the load.
PWRGD1, PWRGD2 (Pins 22, 15/Pins 19, 12): Power
Good. The PWRGD flag is an open-collector flag to indicate
that the output voltage has increased above 90% of the
nominal output voltage. There is no internal pull-up on
this pin; a pull-up resistor must be used. The PWRGD pin
changes state from an open-collector pull-down to high
impedance after the output increases above 90% of the
nominal voltage. The maximum pull-down current of the
PWRGD pin in the low state is 100μA.
SHDN1, SHDN2 (Pins 23, 14/Pins 20, 11): Shutdown.
Pulling the SHDN1 or SHDN2 pin low puts its corresponding LT3030 channel into a low power state and turns its
output off. The SHDN1 and SHDN2 pins are completely
independent of each other, and each SHDN pin only affects
operation on its corresponding channel. Drive the SHDN1
and SHDN2 pins with either logic or an open collector/drain
with pull-up resistors. The resistors supply the pull-up
current to the open collectors/drains and the SHDN1 or
SHDN2 current, typically less than 1μA. If unused, connect SHDN1 and SHDN2 to their corresponding IN pins.
Each channel will be in its low power shutdown state if its
corresponding SHDN pin is not connected.
ADJ1, ADJ2 (Pins 27, 10/Pins 1, 10): Adjust Pin. These
are the error amplifier inputs. These pins are internally
clamped to ±9V. A typical input bias current of 30nA flows
into the pins (see curve of ADJ1/ADJ2 Pin Bias Current vs
Temperature in the Typical Performance Characteristics
section). The ADJ1 and ADJ2 pin voltages are 1.220V
referenced to ground and the output voltage range is
1.220V to 19.5V.
BYP1, BYP2 (Pins 28, 9/Pins 2, 9): Bypass. Connecting
a capacitor between OUT and BYP of a respective channel bypasses the LT3030 reference to achieve low noise
performance, improve transient response and soft-start
the output. Internal circuitry clamps the BYP1/BYP2 pins
to ±0.6V (one VBE) from ground. A small capacitor from
the corresponding output to this pin bypasses the reference to lower the output voltage noise. Using a maximum
value of 10nF reduces the output voltage noise to a typical
20μVRMS over a 10Hz to 100kHz bandwidth. If not used,
this pin must be left unconnected.
3030f
For more information www.linear.com/3030
11
LT3030
Applications Information
The LT3030 is a dual 750mA/250mA low dropout regulator
with independent inputs, micropower quiescent current
and shutdown. The device supplies up to 750mA/250mA
from the outputs of channel 1/channel 2 at a typical dropout
voltage of 300mV. The two regulators share common GND
pins and are thermally coupled. However, the two inputs
and outputs of the LT3030 operate independently. Each
channel can be shut down independently, but a thermal
shutdown fault on either channel shuts off the output on
both channels. The addition of a 10nF reference bypass capacitor lowers output voltage noise to 20μVRMS over a 10Hz
to 100kHz bandwidth. Additionally, the reference bypass
capacitor improves transient response of the regulator,
lowering the settling time for transient load conditions. The
low operating quiescent current (120μA/75μA for channel
1/2) drops to typically less than 1μA in shutdown. In addition to the low quiescent current, the LT3030 regulator
incorporates several protection features that make it ideal
for use in battery powered systems. Most importantly,
the device protects itself against reverse input voltages.
Adjustable Operation
Each of the LT3030’s channels has an output voltage range
of 1.220V to 19.5V. Figure 1 illustrates that the output
voltage is set by the ratio of two external resistors. The
device regulates the output to maintain the corresponding
ADJ pin voltage at 1.220V referenced to ground. R1’s current equals 1.220V/R1. R2’s current equals R1’s current
plus the ADJ pin bias current. The ADJ pin bias current,
30nA at 25°C, flows through R2 into the ADJ pin. Use
the formula in Figure 1 to calculate output voltage. Linear
Technology recommends that the value of R1 be less than
243k to minimize errors in the output voltage due to the
ADJ pin bias current. In shutdown, the output turns off
and the divider current is zero. Curves of ADJ Pin Voltage
vs Temperature and ADJ Pin Bias Current vs Temperature
appear in the Typical Performance Characteristics section.
Linear Technology tests and specifies each LT3030 channel
with its ADJ pin tied to the corresponding OUT pin for a
1.220V output voltage. Specifications for output voltages
greater than 1.220V are proportional to the ratio of desired
output voltage to 1.220V:
VOUT /1.220V
LT3030
OUT1/OUT2
VIN
IN1/IN2
VOUT
R2
COUT
ADJ1/ADJ2
GND
3030 F01
⎛ R2 ⎞
VOUT = 1.220V ⎜1+ ⎟ + (I ADJ) (R2)
⎝ R1⎠
VADJ = 1.220V
IADJ = 30nA AT 25°C
R1
OUTPUT RANGE = 1.220V TO 19.5V
Figure 1. Adjustable Operation
For example, load regulation on OUT2 for an output current change of 1mA to full load current is typically –2mV
at VOUT2 = 1.220V. At VOUT2 = 2.5V, load regulation is:
(2.5V/1.220V) • (–2mV) = –4.1mV
Table 1 shows 1% resistor divider values for some common output voltages with a resistor divider current of
approximately 5μA.
Table 1. Output Voltage Resistor Divider Values
VOUT (V)
1.5
1.8
2.5
3
3.3
5
R1 (k)
237
237
243
232
210
200
R2 (k)
54.9
113
255
340
357
619
Bypass Capacitance and Low Noise Performance
Using a bypass capacitor connected between a channel’s
BYP pin and its corresponding OUT pin significantly lowers LT3030 output voltage noise, but is not required in
all applications. Linear Technology recommends a good
quality low leakage capacitor. This capacitor bypasses
the regulator’s reference, providing a low frequency noise
pole. A 10nF bypass capacitor introduces a noise pole that
decreases output voltage noise to as low as 20μVRMS. Using
a bypass capacitor provides the added benefit of improving transient response. With no bypass capacitor and a
10μF output capacitor, a 100mA to full load step settles to
within 1% of its final value in approximately 400μs. With
the addition of a 10nF bypass capacitor and evaluating
the same load step, output voltage excursion stays within
2% (see Transient Response in the Typical Performance
Characteristics section). Using a bypass capacitor makes
regulator start-up time proportional to the value of the
bypass capacitor. For example, a 10nF bypass capacitor
and 10μF output capacitor slow start-up time to 15ms.
3030f
12
For more information www.linear.com/3030
LT3030
Applications Information
Input Capacitance and Stability
Each LT3030 channel is stable with an input capacitor
typically between 1µF and 10µF. Applications operating
with smaller VIN to VOUT differential voltages and that experience large load transients may require a higher input
capacitor value to prevent input voltage droop and letting
the regulator enter dropout.
Very low ESR ceramic capacitors may be used. However,
in cases where long wires connect the power supply to the
LT3030’s input and ground, use of low value input capacitors combined with an output load current of greater than
20mA may result in instability. The resonant LC tank circuit
formed by the wire inductance and the input capacitor is
the cause and not a result of LT3030 instability.
The self-inductance, or isolated inductance, of a wire
is directly proportional to its length. However, the wire
diameter has less influence on its self inductance. For
example, the self-inductance of a 2-AWG isolated wire
with a diameter of 0.26" is about half the inductance of a
30-AWG wire with a diameter of 0.01". One foot of 30-AWG
wire has 465nH of self-inductance.
Several methods exist to reduce a wire’s self-inductance.
One method divides the current flowing towards the LT3030
between two parallel conductors. In this case, placing the
wires further apart reduces the inductance; up to a 50%
reduction when placed only a few inches apart. Splitting
the wires connects two equal inductors in parallel. However, when placed in close proximity to each other, mutual
inductance adds to the overall self inductance of the wires.
The most effective technique to reducing overall inductance
is to place the forward and return current conductors (the
input wire and the ground wire) in close proximity. Two
30-AWG wires separated by 0.02" reduce the overall self
inductance to about one-fifth of a single wire.
If a battery, mounted in close proximity, powers the LT3030,
a 1μF input capacitor suffices for stability. However, if a
distantly located supply powers the LT3030, use a larger
value input capacitor. Use a rough guideline of 1μF (in
addition to the 1μF minimum) per 8 inches of wire length.
The minimum input capacitance needed to stabilize the
application also varies with power supply output impedance variations. Placing additional capacitance on the
LT3030’s output also helps. However, this requires an
order of magnitude more capacitance in comparison with
additional LT3030 input bypassing. Series resistance between the supply and the LT3030 input also helps stabilize
the application; as little as 0.1Ω to 0.5Ω suffices. This
impedance dampens the LC tank circuit at the expense of
dropout voltage. A better alternative is to use higher ESR
tantalum or electrolytic capacitors at the LT3030 input in
place of ceramic capacitors.
Output Capacitance and Transient Response
The LT3030 is stable with a wide range of output capacitors.
The ESR of the output capacitor affects stability, most notably with small capacitors. Linear Technology recommends
a minimum output capacitor of 10μF/3.3μF (channel 1
/channel 2) with an ESR of 3Ω, or less, to prevent oscillations. The LT3030 is a micropower device, and output
transient response is a function of output capacitance.
Larger values of output capacitance decrease the peak
deviations and provide improved transient response for
larger load current changes.
Ceramic capacitors require extra consideration. Manufacturers make ceramic capacitors with a variety of dielectrics,
each with different behavior across temperature and applied
voltage. The most common dielectrics specify the EIA
temperature characteristic codes of Z5U, Y5V, X5R and
X7R. Z5U and Y5V dielectrics provide high C-V products
in a small package at low cost, but exhibit strong voltage
and temperature coefficients, as shown in Figure 2 and
Figure 3. When used with a 5V regulator, a 16V 10μF Y5V
capacitor can exhibit an effective value as low as 1μF to
2μF for the applied DC bias voltage and over the operating temperature range. X5R and X7R dielectrics result in
more stable characteristics and are more suitable for use
as the output capacitor. The X7R type has better stability
across temperature, while the X5R is less expensive and
is available in higher values.
Exercise care even when using X5R and X7R capacitors;
the X5R and X7R codes only specify operating temperature
range and maximum capacitance change over temperature.
Capacitance change due to DC bias (voltage coefficient)
with X5R and X7R capacitors is better than with Y5V and
Z5U capacitors, but can still be significant enough to drop
3030f
For more information www.linear.com/3030
13
LT3030
Applications Information
capacitor values below appropriate levels. Capacitor DC
bias characteristics tend to improve as case size increases.
Linear Technology recommends verifying expected versus
actual capacitance values at operating voltage in situ for
an application.
20
BOTH CAPACITORS ARE 16V,
1210 CASE SIZE, 10µF
CHANGE IN VALUE (%)
0
X5R
–20
–40
–60
Y5V
Shutdown/UVLO
–80
–100
0
2
4
14
8
6
10 12
DC BIAS VOLTAGE (V)
16
3030 F02
Figure 2. Ceramic Capacitor
DC Bias Characteristics
40
20
CHANGE IN VALUE (%)
Voltage and temperature coefficients are not the only
sources of problems. Some ceramic capacitors have a
piezoelectric response. A piezoelectric device generates
voltage across its terminals due to mechanical stress,
similar to the way a piezoelectric accelerometer or microphone works. For a ceramic capacitor, the stress can be
induced by vibrations in the system or thermal transients.
The resulting voltages produced can cause appreciable
amounts of noise, especially when a ceramic capacitor is
used for noise bypassing. A ceramic capacitor produced
the trace's response to light tapping from a pencil, as
shown in Figure 4. Similar vibration induced behavior can
masquerade as increased output voltage noise.
X5R
0
The SHDN pin is used to put the LT3030 into a micropower
shutdown state. The LT3030 has an accurate 1.21V
threshold (during turn-on) on the SHDN pin. This threshold
can be used in conjunction with a resistor divider from the
system input supply to define an accurate undervoltage
lockout (UVLO) threshold for the regulator. The SHDN pin
current (at the threshold) needs to be considered when
determining the resistor divider network.
PWRGD Flag
–20
–40
Y5V
–60
–80
BOTH CAPACITORS ARE 16V,
1210 CASE SIZE, 10µF
–100
50
25
75
–50 –25
0
TEMPERATURE (°C)
100
125
3030 F03
Figure 3. Ceramic Capacitor
Temperature Characteristics
COUT = 10µF
CBYP = 0.01µF
ILOAD = 750mA
VOUT
500µV/DIV
The PWRGD flag indicates that the ADJ pin voltage is
within 10% of the regulated voltage. The PWRGD pin is an
open-collector output, capable of sinking 100μA of current
when the ADJ pin voltage is below 90% of the regulated
voltage. There is no internal pull-up on the PWRGD pin;
an external pull-up resistor must be used. As the ADJ
pin voltage rises above 90% of its regulated voltage, the
PWRGD pin switches to a high impedance state and the
external pull-up resistor pulls the PWRGD pin voltage up.
During normal operation, an internal glitch filter prevents
the PWRGD pin from switching to a low voltage state if
the ADJ pin voltage falls below the regulated voltage by
more than 10% in a short transient (<40μs typical) event.
Thermal Considerations
100ms/DIV
3030 F04
Figure 4. Noise Resulting from Tapping on a Ceramic Capacitor
The LT3030’s power handling capability limits the maximum rated junction temperature (125°C, LT3030E/LT3030I
or 150°C, LT3030H/LT3030MP). Two components comprise the power dissipated by each channel:
3030f
14
For more information www.linear.com/3030
LT3030
Applications Information
1. Output current multiplied by the input/output voltage
differential: (IOUT)(VIN – VOUT), and
2.GND pin current multiplied by the input voltage:
(IGND)(VIN).
Table 3. FE Package, 20-Lead TSSOP
COPPER AREA
TOPSIDE*
BACKSIDE
2500mm2
2500mm2
2500mm2
1000mm2
2
2500mm2
225mm
2
2500mm2
100mm
THERMAL RESISTANCE
BOARD AREA (JUNCTION-TO-AMBIENT)
2500mm2
25°C/W
2500mm2
27°C/W
2
2500mm
28°C/W
2500mm2
32°C/W
Ground pin current is found by examining the GND Pin
Current curves in the Typical Performance Characteristics
section.
*Device is mounted on topside.
Power dissipation for each channel equals the sum of the
two components listed above. Total power dissipation for
the LT3030 equals the sum of the power dissipated by
each channel.
The junction-to-case thermal resistance (θJC), measured
at the exposed pad on the back of the die, is 3.4°C/W for
the QFN package, and 10°C/W for the TSSOP package.
The LT3030’s internal thermal shutdown circuitry
protects both channels of the device if either channel
experiences an overload or fault condition. Activation
of the thermal shutdown circuitry turns both channels
off. If the overload or fault condition is removed, both
outputs are allowed to turn back on. For continuous normal conditions, do not exceed the maximum
junction temperature rating of 125°C (LT3030E/LT3030I)
or 150°C (LT3030H/LT3030MP).
Carefully consider all sources of thermal resistance from
junction-to-ambient, including additional heat sources
mounted in proximity to the LT3030. For surface mount
devices, use the heat spreading capabilities of the PC board
and its copper traces to accomplish heat sinking. Copper
board stiffeners and plated through-holes can also spread
the heat generated by power devices.
Calculating Junction Temperature
Example: Channel 1’s output voltage is set to 1.8V.
Channel 2’s output voltage is set to 1.5V. Each channel’s
input voltage is 2.5V. Channel 1’s output current range
is 0mA to 750mA. Channel 2’s output current range is
0mA to 250mA. The application has a maximum ambient
temperature of 50°C. What is the LT3030’s maximum
junction temperature?
The power dissipated by each channel equals:
IOUT(MAX)(VIN – VOUT) + IGND (VIN)
where for output 1:
IOUT(MAX) = 750mA
VIN = 2.5V
IGND at (IOUT = 750mA, VIN = 2.5V) = 13mA
The following tables list thermal resistance as a function of
copper area in a fixed board size. All measurements were
taken in still air on a four-layer FR-4 board with 1oz solid
internal planes, and 2oz external trace planes with a total
board thickness of 1.6mm. For further information on thermal resistance and using thermal information, refer to JEDEC
standard JESD51, notably JESD 51-7 and JESD 51-12.
For output 2:
Table 2. UFD Package, 28-Lead QFN
For output 2:
COPPER AREA
TOPSIDE*
2500mm2
1000mm2
225mm2
100mm2
BACKSIDE
2500mm2
2500mm2
2500mm2
2500mm2
BOARD AREA
2500mm2
2500mm2
2500mm2
2500mm2
*Device is mounted on topside.
THERMAL RESISTANCE
(JUNCTION-TO-AMBIENT)
30°C/W
32°C/W
33°C/W
35°C/W
IOUT(MAX) = 250mA
VIN = 2.5V
IGND at (IOUT = 250mA, VIN = 2.5V) = 4.5mA
So, for output 1:
P = 750mA (2.5V – 1.8V) + 13mA (2.5V) = 0.56W
P = 250mA (2.5V – 1.5V) + 4.5mA (2.5V) = 0.26W
The thermal resistance is in the range of 25°C/W to 35°C/W,
depending on the copper area. So, the junction temperature
rise above ambient temperature approximately equals:
(0.56W + 0.26W) 30°C/W = 24.6°C
3030f
For more information www.linear.com/3030
15
LT3030
Applications Information
TJMAX = 50°C + 24.6°C = 74.6°C
Protection Features
The LT3030 regulator incorporates several protection features that make it ideal for use in battery-powered circuits.
In addition to the normal protection features associated with
monolithic regulators, such as current limiting and thermal
limiting, the device protects itself against reverse input voltages and reverse voltages from output to input. The two
regulators have independent inputs, a common GND pin
and are thermally coupled. However, the two channels of
the LT3030 operate independently. Each channel’s output
can be shut down independently, and a fault condition on
one output does not affect the other output electrically,
unless the thermal shutdown circuitry is activated.
Current limit protection and thermal overload protection
protect the device against current overload conditions at
each output of the LT3030. For normal operation, do not
allow the junction temperature to exceed 125°C (LT3030E/
LT3030I) or 150°C (LT3030H/LT3030MP). The typical
thermal shutdown temperature threshold is 165°C and
the circuitry incorporates approximately 5°C of hysteresis.
Each channel’s input withstands reverse voltages of 22V.
Current flow into the device is limited to less than 1mA
(typically less than 100μA) and no negative voltage appears
at the respective channel’s output. The device protects
both itself and the load against batteries that are plugged
in backwards.
The LT3030 incurs no damage if either channel’s output
is pulled below ground. If the input is left open-circuit,
or grounded, the output can be pulled below ground by
22V. The output acts like an open circuit, and no current
flows from the output. However, current flows in (but is
limited by) the external resistor divider that sets the output
voltage. If the input is powered by a voltage source, the
output sources current equal to its current limit capability and the LT3030 protects itself by its thermal limiting
circuitry. In this case, grounding the relevant SHDN1 or
SHDN2 pin turns off its channel’s output and stops that
output from sourcing current.
16
The LT3030 incurs no damage if either ADJ pin is pulled
above or below ground by 9V. If the input is left open
circuit or grounded, the ADJ pins perform like an open
circuit down to –1.5V, and then like a 1.2k resistor down
to –9V when pulled below ground. When pulled above
ground, the ADJ pins perform like an open circuit up to
0.5V, then like a 5.7k resistor up to 3V, then like a 1.8k
resistor up to 9V.
In situations where an ADJ pin connects to a resistor divider
that would pull the pin above its 9V clamp voltage if the
output is pulled high, the ADJ pin input current must be
limited to less than 5mA. For example, assume a resistor
divider sets the regulated output voltage to 1.5V, and the
output is forced to 20V. The top resistor of the resistor
divider must be chosen to limit the current into the ADJ
pin to less than 5mA when the ADJ pin is at 9V. The 11V
difference between the OUT and ADJ pins divided by the
5mA maximum current into the ADJ pin yields a minimum
top resistor value of 2.2k.
In circuits where a backup battery is required, several
different input/output conditions can occur. The output
voltage may be held up while the input is either pulled
to ground, pulled to some intermediate voltage or is left
open-circuit. Current flow back into the output follows the
curve shown in Figure 5.
If either of the LT3030’s IN pins is forced below its corresponding OUT pin, or the OUT pin is pulled above its
corresponding IN pin, input current for that channel typically
5.0
TJ = 25°C
VIN1 = VIN2 = 0V
VADJ1 = VOUT1
VADJ2 = VOUT2
4.5
REVERSE CURRENT (mA)
The maximum junction temperature then equals the maximum ambient temperature plus the maximum junction
temperature rise above ambient temperature, or:
4.0
3.5
3.0
2.5
IADJ1 OR IADJ2
2.0
1.5
1.0
0.5
0
For more information www.linear.com/3030
IOUT1 OR IOUT2
0
1
2
5
3
4
6
7
OUTPUT VOLTAGE (V)
8
9
3030 F05
IADJ = FLOWS INTO ADJ PIN TO GND PIN
IOUT = FLOWS INTO OUT PIN TO IN PIN
Figure 5. Reverse Output Current
3030f
LT3030
Applications Information
drops to less than 2μA. This occurs if the IN pin is connected to a discharged (low voltage) battery, and either
a backup battery or a second regulator circuit holds up
the output. The state of that channel’s SHDN pin has no
effect on the reverse output current if the output is pulled
above the input.
When power is first applied, as input voltage rises, the
output follows the input, allowing the regulator to start-up
into heavy loads. During start-up, as the input voltage is
rising, the input-to-output voltage differential is small, allowing the regulator to supply large output currents. With
a high input voltage, an event can occur wherein removal
of an output short will not allow the output to recover. The
event occurs with a heavy output load when the input voltage
is high and the output voltage is low. Common situations
occur immediately after the removal of a short-circuit or if
the shutdown pin is pulled high after the input voltage has
already been turned on. The load line intersects the output
current curve at two points creating two stable output operating points for the regulator. With this double intersection,
the input power supply may need to be cycled down to zero
and brought up again to make the output recover.
Overload Recovery
Like many IC power regulators, the LT3030 has safe
operating area (SOA) protection. The safe area protection decreases current limit as input-to-output voltage
increases and keeps the power transistor inside a safe
operating region for all values of input-to-output voltage.
The protective design provides some output current at
all values of input-to-output voltage up to the specified
maximum operational input voltage of 20V.
Typical Applications
Coincident Tracking Supply Application
3.3V
0.1µF
OFF ON
ON
GATE
LTC2923
RAMP
RAMPBUF
113k
1%
90.9k
1%
VCC
TRACK1
IN1
1M
3.3µF
LT3030
10nF
PWRGD1
BYP1
SHDN1
ADJ1
FB2
3.3µF
IN2
OUT2
10nF
1M
PWRGD2
GND
BYP2
SHDN2
113k
1%
10µF
VOUT1
1.8V
750mA
237k
1%
SDO
2.5V
TRACK2
OUT1
1M
FB1
54.9k
1%
63.4k
1%
CGATE
0.1µF
ADJ2
54.9k
1%
VOUT2
1.5V
3.3µF 250mA
237k
1%
GND
3030 TA02a
VOUT1
VOUT2
500mV/DIV
20ms/DIV
3030 TA02b
3030f
For more information www.linear.com/3030
17
LT3030
Package Description
Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings.
UFD Package
28-Lead (4mm × 5mm) Plastic QFN
(Reference LTC DWG # 05-08-1712 Rev B)
0.70 ±0.05
4.50 ± 0.05
3.10 ± 0.05
2.50 REF
2.65 ± 0.05
3.65 ± 0.05
PACKAGE OUTLINE
0.25 ±0.05
0.50 BSC
3.50 REF
4.10 ± 0.05
5.50 ± 0.05
RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS
APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED
4.00 ± 0.10
(2 SIDES)
R = 0.05
TYP
0.75 ± 0.05
PIN 1 NOTCH
R = 0.20 OR 0.35
× 45° CHAMFER
2.50 REF
R = 0.115
TYP
27
28
0.40 ± 0.10
PIN 1
TOP MARK
(NOTE 6)
1
2
5.00 ± 0.10
(2 SIDES)
3.50 REF
3.65 ± 0.10
2.65 ± 0.10
(UFD28) QFN 0506 REV B
0.200 REF
0.00 – 0.05
0.25 ± 0.05
0.50 BSC
BOTTOM VIEW—EXPOSED PAD
NOTE:
1. DRAWING PROPOSED TO BE MADE A JEDEC PACKAGE OUTLINE MO-220 VARIATION (WXXX-X).
2. DRAWING NOT TO SCALE
3. ALL DIMENSIONS ARE IN MILLIMETERS
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE
5. EXPOSED PAD SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION
ON THE TOP AND BOTTOM OF PACKAGE
3030f
18
For more information www.linear.com/3030
LT3030
Package Description
Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings.
FE Package
20-Lead Plastic TSSOP (4.4mm)
(Reference LTC DWG # 05-08-1663 Rev J)
FE Package
20-Lead Plastic
TSSOP
(4.4mm)
Exposed
Pad
Variation CB
(Reference LTC DWG # 05-08-1663 Rev J)
Exposed Pad Variation CB
6.40 – 6.60*
(.252 – .260)
3.86
(.152)
3.86
(.152)
20 1918 17 16 15 14 13 12 11
6.60 ±0.10
2.74
(.108)
4.50 ±0.10
6.40
2.74 (.252)
(.108) BSC
SEE NOTE 4
0.45 ±0.05
1.05 ±0.10
0.65 BSC
1 2 3 4 5 6 7 8 9 10
RECOMMENDED SOLDER PAD LAYOUT
4.30 – 4.50*
(.169 – .177)
0.09 – 0.20
(.0035 – .0079)
0.25
REF
0.50 – 0.75
(.020 – .030)
NOTE:
1. CONTROLLING DIMENSION: MILLIMETERS
MILLIMETERS
2. DIMENSIONS ARE IN
(INCHES)
3. DRAWING NOT TO SCALE
1.20
(.047)
MAX
0° – 8°
0.65
(.0256)
BSC
0.195 – 0.30
(.0077 – .0118)
TYP
0.05 – 0.15
(.002 – .006)
FE20 (CB) TSSOP REV J 1012
4. RECOMMENDED MINIMUM PCB METAL SIZE
FOR EXPOSED PAD ATTACHMENT
*DIMENSIONS DO NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.150mm (.006") PER SIDE
3030f
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection
its circuits
as described
herein will not infringe on existing patent rights.
Forofmore
information
www.linear.com/3030
19
LT3030
Typical Application
Sequencing Supply Application
VIN1
3.3V
LT3030
1µF
1M
OUT1
IN1
VIN2
2.5V
1µF
10nF
SHDN1
BYP1
PWRGD1
ADJ1
IN2
OUT2
10nF
BYP2
SHDN2
22µF
VOUT2
1V/DIV
237k
1%
1M
PWRGD2
113k
1%
VOUT1
1.8V
750mA
54.9k
1%
10µF
VOUT2
1.5V
250mA
ADJ2
VOUT1
1V/DIV
VSHDN1
5V/DIV
10ms/DIV
3030 TA03b
237k
1%
GND
3030 TA03a
Related Parts
PART NUMBER DESCRIPTION
COMMENTS
LT1761
100mA, Low Noise Micropower LDO
VIN: 1.8V to 20V, VOUT = 1.22V, VDO = 0.3V, IQ = 20μA, ISD <1μA, Low Noise < 20μVRMS,
Stable with 1μF Ceramic Capacitors, ThinSOT™ Package
LT1763
500mA, Low Noise Micropower LDO
VIN: 1.8V to 20V, VOUT = 1.22V, VDO = 0.3V, IQ = 30μA, ISD <1μA, Low Noise < 20μVRMS,
S8 Package
LT1963/
LT1963A
1.5A, Low Noise, Fast Transient Response VIN: 2.1V to 20V, VOUT(MIN) = 1.21V, VDO = 0.34V, IQ = 1mA, ISD < 1μA,
Low Noise: < 40μVRMS, “A” Version Stable with Ceramic Capacitors, DD, TO220-5, SOT223,
LDOs
S8 Packages
LT1964
200mA, Low Noise Micropower, Negative VIN: –2.2V to –20V, VOUT(MIN) = 1.21V, VDO = 0.34V, IQ = 30μA, ISD = 3μA,
Low Noise: <30μVRMS, Stable with Ceramic Capacitors, ThinSOT Package
LDO
LT1965
1.1A, Low Noise, Fast Transient Response VIN: 1.8V to 20V, VOUT(MIN) = 1.20V, VDO = 0.3V, IQ = 0.5mA, ISD < 1μA,
Low Noise: < 40μVRMS, Stable with Ceramic Capacitors, 3mm × 3mm DFN,
LDO
MS8E, DD-Pak, TO-220 Packages
LT3023
Dual 100mA, Low Noise, Micropower
LDO
VIN: 1.8V to 20V, VOUT(MIN) = 1.22V, VDO = 0.30V, IQ = 40μA, ISD <1μA, DFN,
MS10 Packages
LT3024
Dual 100mA/500mA, Low Noise,
Micropower LDO
VIN: 1.8V to 20V, VOUT(MIN) = 1.22V, VDO = 0.30V, IQ = 60μA, ISD <1μA, DFN,
TSSOP-16E Packages
LT3027
Dual 100mA, Low Noise, Micropower
LDO with Independent Inputs
VIN: 1.8V to 20V, VOUT(MIN) = 1.22V, VDO = 0.30V, IQ = 40μA, ISD <1μA, DFN,
MS10E Packages
LT3028
Dual 100mA/500mA, Low Noise,
VIN: 1.8V to 20V, VOUT(MIN) = 1.22V, VDO = 0.30V, IQ = 60μA, ISD <1μA, DFN,
Micropower LDO with Independent Inputs TSSOP-16E Packages
LT3029
Dual 500mA/500mA, Low Noise,
VIN: 1.8V to 20V, VOUT(MIN) = 1.215V, VDO = 0.30V, IQ = 55μA, ISD <1μA, DFN,
Micropower LDO with Independent Inputs MSOP-16E Packages
LT3032
Dual 150mA Positive/Negative Low
Noise, Low Dropout Linear Regulator
VIN: ±2.3V to ±20V, VOUT(MIN) = ±1.22V, VDO = 0.30V, IQ = 30μA, ISD <1μA,
14-Lead DFN Package
LT3080/
LT3080-1
1.1A, Parallelable, Low Noise LDO
300mV Dropout Voltage (2-Supply Operation), Low Noise 40µVRMS, VIN = 1.2V to 36V,
VOUT: 0V to 35.7V, Current-Based Reference with 1-Resistor VOUT Set, Directly Parallelable
(No Op Amp Required), Stable with Ceramic Capacitors, TO-220, SOT-223, MSOP and
3mm × 3mm DFN
3030f
20 Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
For more information www.linear.com/3030
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com/3030
LT 0213 • PRINTED IN USA
 LINEAR TECHNOLOGY CORPORATION 2013