ON MC10H330FNR2G Quad bus driver/receiver with 2−to−1 output multiplexer Datasheet

MC10H330
Quad Bus Driver/Receiver
with 2−to−1 Output
Multiplexers
Description
http://onsemi.com
The MC10H330 is a Quad Bus Driver/Receiver with two−to−one
output multiplexers. These multiplexers have a common select and
output enable. When disabled, (OE = high) the bus outputs go to
−2.0 V. Their output can be brought to a low state (VOL) by applying a
high level to the receiver enable (RE = High). The parameters
specified are with 25 W loading on the bus drivers and 50 W loads on
the receivers.
MARKING DIAGRAMS*
24
MC10H330L
AWLYYWW
Features
• Propagation Delay, 1.5 ns Typical Data−to−Output
• Improved Noise Margin 150 mV (Over Operating Voltage and
•
•
•
Temperature Range)
Voltage Compensated
MECL 10K™ Compatible
Pb−Free Packages are Available*
CDIP−24
L SUFFIX
CASE 758
1
24
MC10H330P
AWLYYWWG
DIP
PIN ASSIGNMENT
PDIP−24
P SUFFIX
CASE 724
VCC
1
24
VCC0
XBUS
2
23
YBUS
WBUS
3
22
ZBUS
VCC0
4
21
OE
X1
5
20
Y0
X0
6
19
Y1
W1
7
18
Z0
W0
8
17
Z1
S
9
16
RE
WIN
10
15
ZIN
XIN
11
14
YIN
VEE
12
13
VCC0
1
1
10H330G
AWLYYWW
PLCC−28
P SUFFIX
CASE 776
A
WL
YY
WW
G
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Package
ORDERING INFORMATION
Pin assignment is for Dual−in−Line Package.
For PLCC pin assignment, see the Pin Conversion Tables on page 18
of the ON Semiconductor MECL Data Book (DL122/D).
See detailed ordering and shipping information in the package
dimensions section on page 3 of this data sheet.
*For additional information on our Pb−Free strategy and soldering details, please
download the ON Semiconductor Soldering and Mounting Techniques
Reference Manual, SOLDERRM/D.
© Semiconductor Components Industries, LLC, 2006
February, 2006 − Rev. 7
1
Publication Order Number:
MC10H330/D
MC10H330
Table 1. MAXIMUM RATINGS
Symbol
Rating
Unit
VEE
Power Supply (VCC = 0)
Characteristic
−8.0 to 0
Vdc
VI
Input Voltage (VCC = 0)
0 to VEE
Vdc
Iout
Output Current
50
100
mA
TA
Operating Temperature Range
0 to +75
°C
Tstg
Storage Temperature Range − Plastic
− Ceramic
−55 to +150
−55 to +165
°C
°C
− Continuous
− Surge
Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit
values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied,
damage may occur and reliability may be affected.
Table 2. ELECTRICAL CHARACTERISTICS (VEE = −5.2 V ±5%) (Note 1)
0°
Symbol
IE
IinH
Characteristic
25°
75°
Min
Max
Min
Max
Min
Max
Unit
Power Supply Current
−
157
−
143
−
157
mA
Input Current High
Pins 5−8, 17−20
Pins 16, 21
Pin 9
−
−
−
667
514
475
−
−
−
417
321
297
−
−
−
417
321
297
0.5
−
0.5
−
0.3
−
mA
mA
IinL
Input Current Low
VOH
High Output Voltage
−1.02
−0.84
−0.98
−0.81
−0.92
−0.735
Vdc
VOL
Low Output Voltage
−1.95
−1.63
−1.95
−1.63
−1.95
−1.60
Vdc
VIH
High Input Voltage
−1.17
−0.84
−1.13
−0.81
−1.07
−0.735
Vdc
VIL
Low Input Voltage
−1.95
−1.48
−1.95
−1.48
−1.95
−1.45
Vdc
1. Each MECL 10H™ series circuit has been designed to meet the dc specifications shown in the test table, after thermal equilibrium has been
established. The circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 lfpm is maintained.
Receiver outputs are terminated through a 50 W resistor to −2.0 Vdc. Bus outputs are terminated through a 25 W resistor to −2.0 Vdc.
Table 3. AC PARAMETERS
0°
Symbol
tpd
Characteristic
Propagation Delay
Select−to−Input
Data−to−Bus Output
Select−to−Bus
Output
OE−to−Bus Output
Bus−to−Input
RE−to−Input
Data−to−Receiver
Input
25°
75°
Min
Max
Min
Max
Min
Max
1.8
0.5
5.3
2.0
1.8
0.5
5.3
2.0
1.8
0.5
5.3
2.0
1.0
0.8
0.8
0.5
3.2
2.2
2.1
2.2
1.0
0.8
0.8
0.5
3.2
2.2
2.1
2.2
1.0
0.8
0.8
0.5
3.2
2.2
2.4
2.2
Unit
ns
1.3
4.0
1.3
4.0
1.3
4.0
tr
Rise Time
0.5
2.0
0.5
2.0
0.5
2.0
ns
tf
Fall Time
0.5
2.0
0.5
2.0
0.5
2.0
ns
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
http://onsemi.com
2
MC10H330
LOGIC DIAGRAM
OE
21
S
9
W0
8
W1
7
WIN
10
X0
6
X1
XIN
5
11
Y0
20
Y1
19
YIN
14
Z0
18
Z1
17
ZIN
15
RE
16
VCC0
VCC
VCC0
VCC0
VEE
MULTIPLEXER TRUTH TABLE
OE
S
WBus
XBus
YBus
H
L
L
X
L
H
−2.0 V −2.0 V −2.0 V −2.0 V
W0
X0
Y0
Z0
W1
X1
Y1
Z1
=
=
=
=
=
PIN 24
PIN 1
PIN 13
PIN 4
PIN 12
3
WBUS
2
XBUS
23
YBUS
22
ZBUS
RECEIVER TRUTH TABLE
ZBus
RE
Win
Xin
Yin
Zin
H
L
L
WBus
L
XBus
L
YBus
L
ZBus
ORDERING INFORMATION
Package
Shipping †
MC10H330FN
PLCC−28
37 Units / Rail
MC10H330FNG
PLCC−28
(Pb−Free)
37 Units / Rail
MC10H330FNR2
PLCC−28
500 / Tape & Reel
MC10H330FNR2G
PLCC−28
(Pb−Free)
500 / Tape & Reel
MC10H330L
CDIP−24
15 Unit / Rail
MC10H330P
PDIP−24
15 Unit / Rail
MC10H330PG
PDIP−24
(Pb−Free)
15 Unit / Rail
Device
http://onsemi.com
3
MC10H330
PACKAGE DIMENSIONS
PLCC−28
FN SUFFIX
PLASTIC PLCC PACKAGE
CASE 776−02
ISSUE D
−N−
0.007 (0.180)
B
Y BRK
T L−M
M
0.007 (0.180)
U
M
N
S
T L−M
S
S
N
S
D
Z
−M−
−L−
W
28
D
X
V
1
G1
A
0.007 (0.180)
R
0.007 (0.180)
C
M
M
T L−M
T L−M
S
S
N
N
S
0.007 (0.180)
H
G
J
S
S
N
M
T L−M
S
N
S
K1
0.004 (0.100)
−T− SEATING
K
PLANE
F
VIEW S
G1
T L−M
N
S
S
E
S
T L−M
S
VIEW D−D
Z
0.010 (0.250)
0.010 (0.250)
0.007 (0.180)
VIEW S
S
NOTES:
1. DATUMS −L−, −M−, AND −N− DETERMINED
WHERE TOP OF LEAD SHOULDER EXITS
PLASTIC BODY AT MOLD PARTING LINE.
2. DIMENSION G1, TRUE POSITION TO BE
MEASURED AT DATUM −T−, SEATING PLANE.
3. DIMENSIONS R AND U DO NOT INCLUDE
MOLD FLASH. ALLOWABLE MOLD FLASH IS
0.010 (0.250) PER SIDE.
4. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
5. CONTROLLING DIMENSION: INCH.
6. THE PACKAGE TOP MAY BE SMALLER THAN
THE PACKAGE BOTTOM BY UP TO 0.012
(0.300). DIMENSIONS R AND U ARE
DETERMINED AT THE OUTERMOST
EXTREMES OF THE PLASTIC BODY
EXCLUSIVE OF MOLD FLASH, TIE BAR
BURRS, GATE BURRS AND INTERLEAD
FLASH, BUT INCLUDING ANY MISMATCH
BETWEEN THE TOP AND BOTTOM OF THE
PLASTIC BODY.
7. DIMENSION H DOES NOT INCLUDE DAMBAR
PROTRUSION OR INTRUSION. THE DAMBAR
PROTRUSION(S) SHALL NOT CAUSE THE H
DIMENSION TO BE GREATER THAN 0.037
(0.940). THE DAMBAR INTRUSION(S) SHALL
NOT CAUSE THE H DIMENSION TO BE
SMALLER THAN 0.025 (0.635).
DIM
A
B
C
E
F
G
H
J
K
R
U
V
W
X
Y
Z
G1
K1
http://onsemi.com
4
INCHES
MIN
MAX
0.485
0.495
0.485
0.495
0.165
0.180
0.090
0.110
0.013
0.019
0.050 BSC
0.026
0.032
0.020
−−−
0.025
−−−
0.450
0.456
0.450
0.456
0.042
0.048
0.042
0.048
0.042
0.056
−−− 0.020
2_
10_
0.410
0.430
0.040
−−−
MILLIMETERS
MIN
MAX
12.32
12.57
12.32
12.57
4.20
4.57
2.29
2.79
0.33
0.48
1.27 BSC
0.66
0.81
0.51
−−−
0.64
−−−
11.43
11.58
11.43
11.58
1.07
1.21
1.07
1.21
1.07
1.42
−−−
0.50
2_
10_
10.42
10.92
1.02
−−−
M
T L−M
S
N
S
MC10H330
PACKAGE DIMENSIONS
CDIP−24
L SUFFIX
CERAMIC DIP PACKAGE
CASE 758−02
ISSUE A
L
B
24
13
1
12
P
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEADS WHEN
FORMED PARALLEL.
J
−A−
DIM
A
B
C
D
F
G
J
K
L
N
P
N
C
SEATING
PLANE
−T−
K
G
D 24 PL
0.25 (0.010)
F
M
T A
PDIP−24
P SUFFIX
PLASTIC DIP PACKAGE
CASE 724−03
ISSUE D
24
13
1
12
NOTES:
1. CHAMFERED CONTOUR OPTIONAL.
2. DIMENSION L TO CENTER OF LEADS WHEN
FORMED PARALLEL.
3. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
4. CONTROLLING DIMENSION: INCH.
−B−
L
C
−T−
NOTE 1
K
M
N
E
G
MILLIMETERS
MIN
MAX
31.50
32.64
7.24
7.75
4.07
5.08
0.38
0.53
1.14
1.57
2.54 BSC
0.20
0.33
2.54
4.19
7.62
7.87
0.51
1.27
9.14
10.16
M
−A−
SEATING
PLANE
INCHES
MIN
MAX
1.240
1.285
0.285
0.305
0.160
0.200
0.015
0.021
0.045
0.062
0.100 BSC
0.008
0.013
0.100
0.165
0.300
0.310
0.020
0.050
0.360
0.400
J
F
D
24 PL
0.25 (0.010)
M
T B
M
24 PL
0.25 (0.010)
M
T A
M
DIM
A
B
C
D
E
F
G
J
K
L
M
N
INCHES
MIN
MAX
1.230
1.265
0.250
0.270
0.145
0.175
0.015
0.020
0.050 BSC
0.040
0.060
0.100 BSC
0.007
0.012
0.110
0.140
0.300 BSC
0_
15_
0.020
0.040
MILLIMETERS
MIN
MAX
31.25
32.13
6.35
6.85
3.69
4.44
0.38
0.51
1.27 BSC
1.02
1.52
2.54 BSC
0.18
0.30
2.80
3.55
7.62 BSC
0_
15_
0.51
1.01
MECL 10H and MECL 10K are trademarks of Motorola, Inc.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
N. American Technical Support: 800−282−9855 Toll Free
Literature Distribution Center for ON Semiconductor
USA/Canada
P.O. Box 61312, Phoenix, Arizona 85082−1312 USA
Phone: 480−829−7710 or 800−344−3860 Toll Free USA/Canada Japan: ON Semiconductor, Japan Customer Focus Center
2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051
Fax: 480−829−7709 or 800−344−3867 Toll Free USA/Canada
Phone: 81−3−5773−3850
Email: [email protected]
http://onsemi.com
5
ON Semiconductor Website: http://onsemi.com
Order Literature: http://www.onsemi.com/litorder
For additional information, please contact your
local Sales Representative.
MC10H330/D
Similar pages