14 Pin Auto-Insertable/SMD Passive Delay Lines PCA Part Number Tap Delay Tol. Total Delay Tol. (& Total Delay) EPA3756G-5*(Z) EPA3756G-7.5*(Z) EPA3756G-10*(Z) EPA3756G-12.5*(Z) EPA3756G-15*(Z) EPA3756G-17.5*(Z) EPA3756G-20*(Z) EPA3756G-25*(Z) EPA3756G-30*(Z) EPA3756G-35*(Z) EPA3756G-40*(Z) EPA3756G-45*(Z) EPA3756G-50*(Z) EPA3756G-60*(Z) 0.50 ± .35 nS 0.75 ± .35 nS 1.00 ± .35 nS 1.25 ± .35 nS 1.50 ± .35 nS 1.75 ± .35 nS 2.00 ± 20% 2.50 ± 20% 3.00 ± 20% 3.50 ± 20% 4.00 ± 20% 4.50 ± 20% 5.00 ± 20% 6.00 ± 1 nS Rise Time nS Max. PCA Part Number (Calculated) (& Total Delay) ± 1 nS ± 1 nS ± 1 nS ± 1 nS ± 1 nS ± 1 nS ± 1 nS ± 5% ± 5% ± 5% ± 5% ± 5% ± 5% ± 5% 1.25 1.50 2.0 2.5 3.0 3.5 4.0 5.0 6.0 7.0 8.0 9.0 10 12 Tap Delay Tol. Total Delay Tol. (Calculated) EPA3756G-70*(Z) EPA3756G-80*(Z) EPA3756G-90*(Z) EPA3756G-100*(Z) EPA3756G-125*(Z) EPA3756G-150*(Z) EPA3756G-175*(Z) EPA3756G-200*(Z) EPA3756G-300*(Z) EPA3756G-350*(Z) EPA3756G-400*(Z) EPA3756G-450*(Z) EPA3756G-500*(Z) 7.00 ± 1 nS 8.00 ± 1 nS 9.00 ± 1 nS 10.00 ± 1 nS 12.50 ± 10% 15.00 ± 10% 17.50 ± 10% 20.00 ± 10% 30.00 ± 10% 35.00 ± 10% 40.00 ± 10% 45.00 ± 10% 50.00 ± 10% ± 5% ± 5% ± 5% ± 5% ± 5% ± 5% ± 5% ± 5% ± 5% ± 5% ± 5% ± 5% ± 5% • Maximum Attenuation: 10 % • Note : *(Z) indicates *(A) = 50 Ω *(B) = 100 Ω *(C) = 200 Ω Pulse Input Voltage Pulse Width % of Total Delay Input Rise Time (10 - 90%) Pulse Repetition Rate @ Td ≤ 150 nS Pulse Repetition Rate @ Td > 150 nS DC Elect. Character. Unit Distortion ±10 % Temperature Coefficient of Delay 100 PPM/°C 1K Dielectric Strength 100 13 3 Volts 300 % 2.0 nS 1.0 MHz 300 KHz Min Max Insulation Resistance @ 100 Vdc 14 16 18 20 25 30 35 40 60 70 80 90 100 • Schematic Input Pulse Test Conditions @ 25°C VIN PW TRI PRR Rise Time nS Max. 2 12 3 11 5 10 6 9 IN 1 OUT 7 14 GROUND 8 Recommended Operating Conditions Min Pulse Width % of Total Delay Meg Ω PW* D* Vdc TA Operating Free Air Temperature Max Unit 200 % Duty Cycle -40 40 % +85 °C *These two values are inter-dependent. Package Dimensions: Auto-Insertable Package Dimensions: Surface Mount Device .055 PCA EPA3756-XX(Z) Date Code White Dot Pin#1 .430 PCA EPA3756G-XX(Z) Date Code .780 Max. Suggested Solder Pad Layout .280 .100 .020 Min. .230 Max. .020 Typ. .280 Max. .03 .780 Max. .010 Typ. .150 Typ. .100 Typ. .450 .365 Max. .010 ± .005 .240 .020 ± .002 .100 ± .005 .040 .340 • (*) Suffix "G" for Surface Mount Device, leave "Blank" for Auto-Insertable • QAF-CSO1 Rev. B 8/25/94 DSD3756-XX(Z) Rev. 1 10/10/05 Unless Otherwise Noted Dimensions in Inches Tolerances: Fractional = ± 1/32 .XX = ± .030 .XXX = ± .010 ELECTRONICS INC. 16799 SCHOENBORN ST. NORTH HILLS, CA 91343 TEL: (818) 892-0761 FAX: (818) 894-5791