Keysight Technologies Multi-Emitter Scenario Generator, Reference Solution Solution Brochure –– Simulate realistic and dynamic radar threat-emitter signal environments consisting of thousands of emitters and millions of pulses-per-second –– Make Angle of Arrival (AoA) measurements in changing signal environments for real-time radar threat-emitter sorting and direction finding –– Quickly and easily set up complex AoA signal scenarios with Signal Studio software Breakthrough Performance and Reliability at a Fraction of the Cost of Traditional EW Simulators Simulating Radar Threat-Emitter Signals for EW Receiver Test When it comes to national defense, the stakes are high. In today’s ever changing radar threat environment, ongoing modernization of electronic warfare (EW) systems is an imperative for many countries. Identifying and neutralizing radar threats accurately and reliably is not an easy task in today’s complex battlefield environments. EW tests are conducted in laboratories to simulate radar threats according to an electronic order of battle. The purpose of a lab EW test is to make the EW system believe that it is flying through a hypothetical battlefield (Figure 1). This is far cheaper and far more time-efficient than putting the system on an airplane and flying over a test range. Validation and verification of EW systems is heavily dependent on testing with realistic signal environments. EW test realism increases as high-fidelity emitters are added to create density. In additon to emitter fidelity and density, platform motion, emitter scan patterns, receiver antenna models, direction of arrival (angle of arrival), multipath and atmospheric models enhance the ability to test EW systems under realistic conditions. EW systems are now designed to identify emitters using precise direction finding and pulse parameterization in dense environments of 8 to 10 million pulses per second. These multi-emitter environments are often simulated with large, complex, expensive custom systems not widely available to EW design engineers as R&D test equipment. The Multi-Emitter Scenario Generator Reference Solution provides a cost effective solution for realistic EW simulation using recent innovations in signal generation including direct digital synthesis, agile frequency and power control. Figure 1. A hypothetical battle off the coast of California with enemy antenna scan patterns in red and friendly in blue. 03 | Keysight | Multi-Emitter Scenario Generator, Reference Solution - Brochure Challenges of Simulating Multi-Emitter Environments The modern spectral environment contains thousands of emitters—radios, wireless devices, and tens to hundreds of radar threats — producing millions of radar pulses per second amidst background signals and noise. In EW design, the multiplicity, density, and bandwidth, make it impractical to use a single source or a small number of sources to simulate a single emitter or a small number of emitters. Cost, space, and complexity considerations rule out these approaches. The most practical solution is to simulate many emitters with a single source, and to employ multiple sources — each typically simulating many emitters — when required to produce the needed signal density or to simulate specific phenomena such as angle-of arrival (AoA). The ability to simulate multiple emitters at multiple frequencies depends on the pulse repetition frequency, duty cycle and number of emitters, and ability of the source to switch between frequency, amplitude, and modulation quickly. In addition to creating emitters with the desired fidelity and density, it is also important to match the geometry and kinematics of EW scenarios since the AoA of a radar threat to the EW system changes slowly compared to other parameters such as center frequency and pulse repetition frequency. EW systems measure AoA and estimate distance using amplitude comparison, differential Doppler, interferometry (phase difference), and time difference of arrival (TDOA). Precise AoA measurements enable precise localization of radar threats. New stand-off jamming systems use active electronically-scanned arrays capable of precise beam forming to minimize loss of jamming power due to beam spreading towards a threat. Moreoever, EW receivers with better AoA capability reduce the need for pulse de-interleaving and sorting. Consequently, AoA is an increasingly important test requirement. Angle of Arrival Methodologies Three common angle of arrival (AoA) or direction finding (DF) methods for EW receivers include: amplitude comparison, time difference of arrival (TDOA), and interferometry. These are all passive monopulse methods which require no cooperation from the threat radar (active homing) and each measures RF pulses from the threat to calculate an AoA. Amplitude comparison method Amplitude comparison monopulse, the most common direction finding method used in radar warning receivers, relies on the ratio signal (P2 /P1 in Figure 2) of two displaced radiation patterns originating from a single phase center that overlaps in the far field. The antenna boresights are oriented (physically squinted) 90 degrees from one another so that the same pulse incident on both patterns has a measureable power difference in each channel. The power difference gives a meaningful arctangent calculation shown in the equation in Figure 2. If the two antenna beams were pointed in the same direction such that P1 and P2 were the same, the arctangent would almost always give 45 degrees. 04 | Keysight | Multi-Emitter Scenario Generator, Reference Solution - Brochure Figure 2. Amplitude comparison monopulse example. Amplitude-comparison monopulse gives 10-15 degree direction finding accuracy because measured cross-channel power levels vary due to aircraft motion and amplitude attenuation or shadowing by the aircraft. For example, the receive power in one channel may be inaccurate because the power was attenuated by the airplane. Often, AoA resolution is more important than the accuracy. The resolution is the ability to distinguish co-located threats such as different radars within the same SAM site. Time difference of arrival and interferometry methods Less commonly used are the time difference of arrival (TDOA) and interferometry AoA methods. TDOA (Figure 3) derives AoA based on the delta time difference an RF pulse is seen at two antennas. Knowing that a signal will travel at the speed of light (c) over a distance equal to the distance between the two antennas, we can take the arcsine of the ratio (TDOA x c)/d to determine the AoA. Although this method does not depend directly on wavelength, it does require precise knowledge of delays through each receive channel, which vary with frequency. Figure 3. TDOA example. 05 | Keysight | Multi-Emitter Scenario Generator, Reference Solution - Brochure Figure 4. Interferometry example. Like TDOA, interferometry (Figure 4) is calculated using the arcsine of a ratio. With interferometry, the EW receiver is measuring the phase difference between apertures, φ. Wavelength, λ, is measured by the EW receiver using an instantaneous frequency measurement receiver (IFM) which gives the frequency of a pulse to ±1 to 3 MHz. The distance between apertures, called a baseline, is known with some uncertainty level. In general, longer baselines are used since this provides better accuracy and less sensitivity to uncertainties. However, at long distances, the phase difference will wrap, leaving ambiguities in this measurement. This is why most modern systems use more than one baseline or a shorter baseline to resolve ambiguities. Cost, size and procurement time benefits Beyond realistic AoA simulations, the reference solution provides other advantages including size, cost and procurement time. Traditional EW systems have been developed using large, expensive proprietary test systems that have long lead times and provide limited support for ongoing end user customization. The reference solution hardware, small enough to fit on an engineer’s desk (Figure 5), is configured with COTS test equipment at a fraction of the cost of typical EW test systems. Because it incorporates COTS hardware and software, it can be delivered in months instead of years. Figure 5. Full EW simulator now fits on an engineer’s desk. 06 | Keysight | Multi-Emitter Scenario Generator, Reference Solution - Brochure Multi-Emitter Scenario Generator, Reference Solution By coherently connecting multiple Keysight N5191A/93A UXG agile signal generators, we can create complex, high pulse density EW scenarios and simulate AoA and kinematics (moving platforms) simultaneously. This combination of UXGs connected together to simulate an electronic battlefield with thousands of emitters is called the Multi-Emitter Scenario Generator Reference Solution (Figure 6). Figure 6. The reference solution includes multiple UXGs, Signal Studio software and calibration equipment. UXG for realistic multi-emitter simulations with AoA Typically, agile signal generators that switch frequency and settle amplitude in the hundreds of nanoseconds are used to simulate all the radar threat-emitters in the environment at different ranges and frequencies with their respective antenna scans. Fast frequency hopping with phase continuity and repeatability allows Keysight’s UXG agile signal generator to simulate multiple pulse-Doppler radars (multiple emitters) at different frequencies while maintaining its original phase (Figure 7). Figure 7. Accurately simulate multiple emitters with a single UXG by taking advantage of built-in phase coherency/repeatability. 07 | Keysight | Multi-Emitter Scenario Generator, Reference Solution - Brochure With multiple UXGs, you can simulate EW scenarios with thousands of radar threat-emitters and millions of pulses per second (the pulse density scales with the number of UXGs). In addition to simulating high pulse density, it’s extremely important to create AoA on all RF pulses for two reasons: 1) AoA allows the EW receiver to localize threats for neutralization and 2) AoA is a primary threat sorting parameter and thus allows the EW receiver to identify groups of pulses as belonging to individual threats. Creating AoA means staggering identical pulses played out of different ports (different UXGs) in time, phase, amplitude, or all three. In order to properly stagger these pulses, the UXGs must be phase, time, frequency and amplitude aligned (calibrated) with each other. The Multi-Emitter Scenario Generator Reference Solution includes tailored calibration routines that work with a number of different measurement receivers — the PNA and PNA-X Vector Network Analyzers, Infiniium oscilloscopes, and U2000 power sensors so that you can choose the right tool for the job. It is this process of calibration that ultimately controls how accurately you can simulate AoA for EW receiver test. Radar warning receiver(s) under test N7660B Signal Studio for Multi-Emitter Scenerio Generation - PC connected to UXGs via GPIB, USB or LAN N5193A UXGs Figure 8. The Multi-Emitter Scenerio Generator Reference Solution combines multiple UXGs to simulate thousands of threat emitters with AoA. Display 08 | Keysight | Multi-Emitter Scenario Generator, Reference Solution - Brochure Reference Solution Key Performance Characteristics Hardware characteristics Frequency range 10 MHz to 40 GHz Phase noise –126 dBc at 10 GHz, 10 kHz offset Non-harmonic spurious –70 dBc at 18 GHz Output power –130 dBm to 10 dBm Normal/list update rate < 180 ns in list mode (frequency, amplitude, phase) Minimum pulse width 10 ns Pulse rise/fall time 3 ns Pulse on/off ratio 90 dB Linear chirp width 10 to 25% of center frequency Time skew (for TDOA AoA method) 100 ps Amplitude accuracy (for amplitude comparison AoA method) < 0.5 dB Phase accuracy (for Interferometry AoA method) 1-3 ° RMS (dependent on center frequency) Height/UXG 3 rack units (3U) Pulse parameters Pulse width stagger Linear ramp, stepped, or staggered specified by timing parameters and number of pulses Modulation on pulse parameters Barker Nested Barker and Barker codes (2, 3, 4, 5, 7, 11, 13) with user control over Barker direction and polarity Formats Custom BPSK and FM chirp (sawtooth or triangle FM chirp deviation of 10-25% of center frequency) Pulse repetition interval parameters PRI stagger Bursted, linear ramp, list, stepped Frequency agility Offset, linear ramp, list, stepped Antenna scan parameters Radiation pattern type Isotropic, Blackman, Cosine1, Cosine2, Cosine3, Cosine4, Cosine5, Exact Blackman, Hamming, Programmable, Rectangular, Three Term, Three Term Minimum, Gaussian, Omni, Pyramidal Horn, Sinc, and Table Lookup Antenna scan type Circular, conical, custom, bidirectional raster, unidirectional raster, bidirectional sector, unidirectional sector, helical, spiral, lobe switching, lobe on target Antenna properties Azimuth/Elevation 3 dB beam width Simulation parameters Multi-emitter simulation Multiple emitters are played from a PDW list according to the capability of the UXG to transition frequency and amplitude according to the number of emitters and their duty cycles Multi-UXG Connect to multiple UXGs to increase pulse density and simulate AoA; angle-of-arrival or multi-channel calibration is provided Emitter interleaving Emitters are interleaved to optimize pulse density and minimize dropped pulses while maintaining accurate pulse width and PRI Dropped pulse reporting and pulse collision reporting Pulse collision percentages and conflicting emitters are reported; modifications to emitter start time and priority can be made in the report to resolve conflicts; report is recalculated when emitter parameters are changed Scenarios Create a hierarchy of platforms, emitters, modes, and waveforms; user can build up a library of emitters or modes and reuse them in different simulations Test system definition Add one or more UXG agile signal generators with different options to the simulation System under test definition Set the minimum simulation power level according to the sensitivity of the receiver under test 09 | Keysight | Multi-Emitter Scenario Generator, Reference Solution - Brochure Reference Solution Key Performance Characteristics (cont’d) Kinematics AoA Provides a dynamic environment with changing power levels, changing Doppler frequency, and changing signal phases between ports, throughout the scenario User-defined ports SUT can have multiple ports identified by the user for AoA; each port is user-assigned to a different UXG Streaming mode LAN streaming Allows the user to save extremely long scenarios to their PC storage and stream the PDWs to the UXG SSD playback Allows the user to store extremely long scenarios (streaming PDW format) on the UXG’s internal SSD drive instead of to the more limited list point memory Time domain analysis Antenna scan display Click and drag the changeable 3-dimensional axis of the view to visualize the antenna scan pattern of any emitters (and associated platforms) in the scenario Trajectory display The motion of the platforms/SUT and their associated emitters (kinematics) is displayed; this view provides basic visual feedback to help confirm that the configured paths are correct 10 | Keysight | Multi-Emitter Scenario Generator, Reference Solution - Brochure Hardware N5193A UXG Agile Signal Generator www.keysight.com/find/n5193a The UXG agile signal generator, the foundation of the reference solution, delivers unmatched performance in switching speed and phase control. To support realistic multithreat scenarios, the UXG can update frequency, amplitude, and phase in as little as 180 ns, generate wide chirps that are 10 to 25 percent of carrier frequency and create pulses as narrow as 10 ns with 3 ns rise/fall times and 90 dB on/off ratio. This is made possible by direct digital synthesis (DDS) technology and a Keysight-proprietary digital-to-analog converter (DAC) that provides industry-leading spurious-free dynamic range (SFDR). Based on an ASIC design that minimizes signal crosstalk and reduces the injection of digital noise into analog circuitry, Keysight’s innovative DAC’s power-supply design and its resampling algorithm enhance signal quality by reducing noise and ensuring linear transitions. Infiniium Oscilloscopes www.keysight.com/find/oscilloscopes Keysight’s Infiniium oscilloscopes offer the industry’s deepest memory and lowest noise floor. Keysight’s RealEdge technology — leading-edge indium phosphide chip technology and custom thin film packaging —combined with time interleaving, frequency interleaving and proprietary signal processing enables us to provide the highest bandwidth lowest-noise real-time oscilloscopes in the world. Infiniium oscilloscopes — ranging from S-Series to Z-Series — are the perfect choice for correcting amplitude and time differences between UXGs. PNA and PNA-X Vector Network Analyzers www.keysight.com/find/pna The PNA and PNA-X Series of microwave network analyzers are the culmination of Keysight ‘s 40-year legacy of technical leadership and innovation in radio frequency (RF) network analysis. More than just a vector network analyzer, the PNA-X is the world’s most integrated and flexible microwave test engine for measuring active devices like amplifiers, mixers, and frequency converters. The combination of two internal signal sources, a signal combiner, S-parameter and noise receivers, pulse modulators and generators, and a flexible set of switches and RF access points provide a powerful hardware core for a broad range of linear and nonlinear measurements, all with a single set of connections to your device-under-test (DUT). Providing up to a maximum frequency of 67 GHz with 128 dB of dynamic range and a noise floor down to -116 dBm, the PNA and PNA-X are perfect for correcting amplitude and phase differences between UXGs. U2000 Series USB Power Sensors www.keysight.com/find/usbsensor Standalone USB-based U2000 Series power sensors enable power measurements without power meters. Using USB power and providing built-in triggering, these power sensors don’t need external power adapters or triggering modules for synchronization with external instruments or events. The U2000 series makes average power measurements from 9 kHz to 24 GHz from -60 to 24 dBm. These features make the U2000 USB power sensors the perfect choice for correcting amplitude differences between UXGs. 11 | Keysight | Multi-Emitter Scenario Generator, Reference Solution - Brochure Software Software recommended for the reference solution includes the N7660B Signal Studio software to set-up and visualize scenarios and calibration software to align multiple UXGs in phase, time and amplitude in order to simulate AoA. N7660B Signal Studio for Multi-Emitter Scenario Generation Signal Studio for multi-emitter scenario generation software provides performance-optimized reference signals– validated by Keysight— to enhance the characterization and verification of your EW systems. Through its application-specific user interface, you can create custom test signals for EW system test. The new kinematics feature provides more dynamic and complex scenarios than can be achieved with static pulse builder software. The dynamic kinematics environment enables changes to power levels, Doppler frequencies, and signal phases between ports, throughout the scenario. These signal changes are based on geometric and physics based models. Simulate signal thresholds and AoA to stimulate the system under test. –– Create multi-emitter scenarios using one or more UXG agile signal generators for EW test from 10 MHz to 40 GHz –– Define radar emitters with a graphical user interface using parameters such as amplitude, frequency, pulse width, modulation-on-pulse, PRI, coherent processing interval, and mechanical and electronic antenna scan modulation –– Define antenna dwells to simulate radars with electronically scanned arrays –– Combine radar signals into multi-emitter scenarios using dropped pulse reports to optimize pulse density –– Reduce pulse collisions by changing emitter start times, priorities, and pulse repetition intervals, and by toggling emitters on and off –– Increase pulse density and reduce dropped pulses by adding more UXGs to the simulation –– Emulate dynamic EW threat scenarios with kinematics (moving platform) simulation: dynamic power levels, Doppler frequency and signal phases for changing AoA simulation –– Simulate long scenarios and stream to UXGs via LAN or the UXG’s internal SSD storage For more information, see webpage at www.keysight.com/find/n7660b. Figure 9. Signal Studio for multi-emiiter scenario generation computes pulse collisions and creates a dropped pulse report before simulating multiple emitters. 12 | Keysight | Multi-Emitter Scenario Generator, Reference Solution - Brochure Software Calibration software The reference solution includes calibration software and three measurement receiver options for calibration: the U2000 series power sensor, the Infiniium series oscilloscopes and the PNA vector network analyzer. Each option provides a different AoA calibration: –– U2000 power sensors for amplitude calibration (amplitude comparison AoA) –– PNA for amplitude and phase calibration (interferometry AoA) –– Infiniium oscilloscopes for amplitude and time calibration (TDOA AoA) Below is a description of the amplitude calibration with the U2000 power sensor. For information on the other calibration methods, contact your Keysight representative. Amplitude calibration software for the U2000 series power sensor The software facilitates setup of connections between USB power sensor(s) and the UXG(s) to measure amplitude corrections over a range of nominal amplitudes and frequencies. The software also supports automation of the programming commands necessary to achieve a multi-box synchronous set of UXGs for use in multi-emitter scenario generation (figure 10). The 32-bit Windows 7 application, exports a comma-separated values (CSV) calibration file compatible with the N7660B Signal Studio for Multi-Emitter Scenario Generation software. The number of USB power sensors required for this correction routine is variable from 1-n. For the best measurement repeatability and lowest amount of manual intervention, we recommend a separate sensor for each UXG. The range of frequencies and amplitudes are constrained by the power sensor used as well as the range of agile frequency switching (electronic attenuator) of the UXG up to 24 GHz. Corrections to power levels as low as -60 dBm are possible depending on the particular model of power sensor used. The maximum power level for a correction is dependent upon the frequency range of the UXG, specified in the data sheet, literature number 5992-0092EN. The software will automatically find all compatible UXGs and U2000A power sensors and add them to a selectable connection grid. Once configured the connections can be verified by a simple self-check routine that ensures that each USB power sensor “sees” each UXG it is logically assigned to by making a quick verification on/off measurement. After a set of correction measurements are made, the software provides results in an easy to view table with statistics for ensuring that the correction is stable. Figure 10. Synchronize multiple UXGs with flexible power sensor calibration GUI. 13 | Keysight | Multi-Emitter Scenario Generator, Reference Solution - Brochure Recommended Configurations and Ordering Information Amplitude only calibration Hardware N5193A Amplitude and phase calibration Hardware UXG X-Series agile signal generator N5193A 1 N5193A-540 Frequency range, 10 MHz to 40 GHz Same options as amplitude only N5193A-FR1 0.001 Hz Frequency resolution N5244A PNA-X microwave network analyzer, 43.5 GHz N5193A-UNT AM, FM, phase modulation, LF output and narrowband chirp N5244A-200 2 ports, single source N5244A-219 N5193A-WC1 Wideband chirp Extended power range and bias-tees to 2 port analyzer N5193A-PM1 Pulse modulation N4692A Electronic calibration module, 10 MHz to 40 GHz N5193A-EP1 Enhanced phase noise N4692A-MOF One female and one male connector, both 2.92 mm N5193A-AT1 Mechanical and solid-state attenuator U2022X 50 MHz - 40 GHz USB power sensor N5193A-SS2 Switching speed - 250 ns U2022XA-100 Connector 2.4 mm N5193A-CC1 100-Pin I/O interface (LVDS) U2002A 50 MHz - 24 GHz USB power sensor Software 1 N7660B Software N7660B Signal Studio for Multi-Emitter Scenario Generation N7660B-4FP Connect to N5193A UXG, fixed perpetual license N7660B-EFP Basic multiple emitters for 1 or more UXG, fixed perpetual license N7660B-FFP Multi-channel for AoA and kinematics, fixed perpetual license Included Calibration software Amplitude and time calibration Hardware N5193A 1 UXG X-Series agile signal generator Same options as amplitude only DSOZ504A Infiniium oscilloscope: 50 GHz Software N7660B Signal Studio for Multi-Emitter Scenario Generation Same options as amplitude only Included 1. Calibration software The N5191A UXG agile signal generator is available for sale without requiring an export license. For more information, see www.keysight. com/find/n5191a. UXG X-Series agile signal generator Signal Studio for Multi-Emitter Scenario Generation Same options as amplitude only Included Calibration software 14 | Keysight | Multi-Emitter Scenario Generator, Reference Solution - Brochure From Hewlett-Packard through Agilent to Keysight For more than 75 years, we‘ve been helping you unlock measurement insights. Our unique combination of hardware, software and people can help you reach your next breakthrough. Unlocking measurement insights since 1939. 1939 THE FUTURE myKeysight www.keysight.com/find/mykeysight A personalized view into the information most relevant to you. Three-Year Warranty www.keysight.com/find/ThreeYearWarranty Keysight’s committed to superior product quality and lower total cost of ownership. Keysight is the only test and measurement company with three-year warranty standard on all instruments, worldwide. And, we provide a one-year warranty on many accessories, calibration devices, systems and custom products. Keysight Assurance Plans www.keysight.com/find/AssurancePlans Up to ten years of protection and no budgetary surprises to ensure your instruments are operating to specification, so you can rely on accurate measurements. Keysight Infoline www.keysight.com/find/service Keysight’s insight to best in class information management. Free access to your Keysight equipment company reports and e-library. Keysight Channel Partners www.keysight.com/find/channelpartners Get the best of both worlds: Keysight’s measurement expertise and product breadth, combined with channel partner convenience. www.keysight.com/find/solution-mesg For more information on Keysight Technologies’ products, applications or services, please contact your local Keysight office. The complete list is available at: www.keysight.com/find/contactus Americas Canada Brazil Mexico United States (877) 894 4414 55 11 3351 7010 001 800 254 2440 (800) 829 4444 Asia Pacific Australia China Hong Kong India Japan Korea Malaysia Singapore Taiwan Other AP Countries 1 800 629 485 800 810 0189 800 938 693 1 800 11 2626 0120 (421) 345 080 769 0800 1 800 888 848 1 800 375 8100 0800 047 866 (65) 6375 8100 Europe & Middle East Austria Belgium Finland France Germany Ireland Israel Italy Luxembourg Netherlands Russia Spain Sweden Switzerland United Kingdom 0800 001122 0800 58580 0800 523252 0805 980333 0800 6270999 1800 832700 1 809 343051 800 599100 +32 800 58580 0800 0233200 8800 5009286 800 000154 0200 882255 0800 805353 Opt. 1 (DE) Opt. 2 (FR) Opt. 3 (IT) 0800 0260637 For other unlisted countries: www.keysight.com/find/contactus (BP-02-10-16) DEKRA Certified ISO9001 Quality Management System www.keysight.com/go/quality Keysight Technologies, Inc. DEKRA Certified ISO 9001:2015 Quality Management System This information is subject to change without notice. © Keysight Technologies, 2016 Published in USA, March 15, 2016 5992-1485EN www.keysight.com