600 mA/1000 mA, 2.5 MHz Buck-Boost DC-to-DC Converter ADP2503/ADP2504 Preliminary Technical Data FEATURES GENERAL DESCRIPTION 1 mm height profile Compact PCB footprint Seamless transition between modes 38 μA typical quiescent current 2.5 MHz operation enables 1 μH inductor Input voltage: 2.3 V to 5.5 V Fixed output voltage: 2.8 V to 5.0 V 600 mA (ADP2503) and 1000 mA (ADP2504) output options Boost converter configuration with load disconnect Sync pin with three different modes: Power save mode (PSM) for improved light load efficiency Forced fixed frequency operation mode Synchronization with external clock Internal compensation Soft start Enable/shutdown logic input Overtemperature protection Short-circuit protection Undervoltage lockout protection Small 10-lead 3 mm × 3 mm LFCSP/QFN package The ADP2503/ADP2504 are high efficiency, low quiescent current step-up/step-down dc-to-dc converters that can operate at input voltages above, below, or equal to the regulated output voltage. The power switches and synchronous rectifiers are internal to minimize external part count. At high load currents, the ADP2503/ADP2504 use a current-mode, fixed frequency PWM control scheme for optimal stability and transient response. To ensure the longest battery life in portable applications, the ADP2503/ADP2504 have an optional power save mode that reduces the switching frequency under light load conditions. For wireless and other low noise applications where variable frequency power save mode may cause interference, the logic control input sync forces fixed frequency PWM operation under all load conditions. The ADP2503/ADP2504 can run from input voltages between 2.3 V and 5.5 V, allowing single lithium or lithium polymer cell, multiple alkaline or NiMH cells, PCMCIA, USB, and other standard power sources. The ADP2503/ADP2504 have fixed output options ranging from 2.8 V to 5 V. Compensation is internal to minimize the number of external components. APPLICATIONS During logic-controlled shutdown, the input is disconnected from the output and draws less than 1 μA from the input source. Operating as a boost converter, the ADP2503/ADP2504 feature a true load disconnect function that isolates the load from the power source. Other key features include under voltage lockout to prevent deep battery discharge and soft start to prevent input current overshoot at startup. Wireless handsets Digital cameras/portable audio players Miniature hard disk power supplies USB powered devices TYPICAL APPLICATION CIRCUIT 1.0µH SW1 VIN 2.3V TO 5.5V 10µF SW2 ADP2503 PVIN VIN VOUT FB VOUT 2.8V TO 5V 22µF EN AGND PGND ON 07475-001 SYNC OFF Figure 1. Application Circuit Rev. PrB Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed byAnalog Devices for its use,nor for any infringements ofpatents or other rights ofthirdparties that may result fromits use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registeredtrademarks arethe property oftheir respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 ©2008 Analog Devices, Inc. All rights reserved. ADP2503/ADP2504 Preliminary Technical Data TABLE OF CONTENTS Features .............................................................................................. 1 Reverse Current Limit ............................................................... 10 Applications ....................................................................................... 1 Power save Mode........................................................................ 10 General Description ......................................................................... 1 Soft Start ...................................................................................... 10 Typical Application Circuit ............................................................. 1 Enable........................................................................................... 11 Revision History ............................................................................... 2 Undervoltage Lockout ............................................................... 11 Specifications..................................................................................... 3 Thermal Shutdown .................................................................... 11 Absolute Maximum Ratings............................................................ 4 Short Circuit Protection ............................................................ 11 Thermal Resistance ...................................................................... 4 Applications Information .............................................................. 12 ESD Caution .................................................................................. 4 Inductor Selection ...................................................................... 12 Pin Configuration and Function Description .............................. 5 PCB Layout Guidelines.................................................................. 14 Typical Performance Characteristics ............................................. 6 Outline Dimensions ....................................................................... 15 Theory of Operation ...................................................................... 10 Ordering Guide .......................................................................... 15 REVISION HISTORY 8/08—Revision PrB Rev. PrB | Page 2 of 16 Preliminary Technical Data ADP2503/ADP2504 SPECIFICATIONS VIN = 3.6 V, VOUT = 3.3 V, @ TA = TJ = −40°C to +125°C for minimum/maximum specifications and TA = +25°C for typical specifications, unless otherwise noted.1 Table 1. Parameters INPUT CHARACTERISTICS Input Voltage Range Undervoltage Lockout Threshold Undervoltage Lockout Threshold OUTPUT CHARACTERISTICS Output Voltage Range Feedback Voltage Feedback Impedance Output Voltage Initial Accuracy (PWM Mode, No Load) Load and Line Regulation CURRENT CHARACTERISTICS Quiescent Current (VIN) Shutdown Current SWITCH CHARACTERISTICS N-Channel Switches (LFCSP) P-Channel Switches (LFCSP) P-Channel Leakage Switch Current Limit ADP2504 ADP2503 Reverse Current Limit OSCILLATOR AND STARTUP Oscillator Frequency On Time PMOS1 (Buck Mode) On Time NMOS2 (Boost Mode) Sync Clock Frequency Sync Clock Minimum Off Time Soft Start Period LOGIC LEVEL CHARACTERISTICS EN, SYNC Input High Threshold EN, SYNC Input Low Threshold EN, SYNC Leakage Current THERMAL CHARACTERISTICS Thermal Shutdown Threshold Thermal Shutdown Hysteresis 1 Conditions Min Typ Max Unit VIN rising VIN falling 2.3 2.2 2.13 2.25 2.18 5.5 2.3 2.23 V V V 5.0 0.55 +2 V V kΩ % 0.5 0.6 % % 50 1 μA μA 1 mΩ mΩ μA 2.0 1.4 1.1 A A A 2.8 200 MHz ns ns MHz ns μs +0.1 V V μA 2.8 0.495 ADP2503/ADP2504 (PWM operation, no load) 0.5 450 −2 VIN = 2.3 V to 3.6 V, ILOAD = 0mA to 500mA, forced PWM mode VIN = 2.3 V to 5.5 V, ILOAD = 0mA to 500mA, forced PWM mode IOUT = 0 mA, V mode = EN = VIN = 3.6 V, device not switching TA = TJ = −40°C to +85°C 38 0.2 VIN = 3.6 V VIN = VOUT = 3.6 V TJ = −40°C to +85°C 150 150 1.3 1.0 VIN = 2.3 V to 5.5 V Minimum duty cycle = 30% Maximum duty cycle = 50% (×2) 2.2 130 2.5 200 2.8 2.2 160 1.2 −1 150 25 All limits at temperature extremes are guaranteed via correlation using standard statistical quality control (SQC). Rev. PrB | Page 3 of 16 0.4 +1 °C °C ADP2503/ADP2504 Preliminary Technical Data ABSOLUTE MAXIMUM RATINGS THERMAL RESISTANCE Table 1. Parameter PVIN, VIN, SW1, SW2, VOUT, SYNC, EN, FB PGND to AGND Operating Ambient Temperature Operating Junction Temperature Storage Temperature Lead Temperature Soldering (10 sec) Vapor Phase (60 sec) Infrared (15 sec) ESD Human Body Model ESD Charged Device Model ESD Machine Model θJA is specified for device soldered JEDEC2S2P PCB. For a typical printed circuit board of a handset, the total thermal resistance is higher. For correct operation up to 85°C ambient temperature the total thermal resistance must not exceed 100 K/W. Rating −0.3 V to +6 V −0.3 V to 0.3 V −40°C to +85°C −40°C to +125°C −65°C to +150°C Table 2. Package Type 10-Lead LFCSP (QFN) 300°C 215°C 220°C ±1000 V ±500 V ±100 V ESD CAUTION Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Absolute maximum ratings apply individually only, not in combination. Unless otherwise specified, all other voltages are referenced to GND. Rev. PrB | Page 4 of 16 θJA 84 Unit °C/W Preliminary Technical Data ADP2503/ADP2504 PIN CONFIGURATION AND FUNCTION DESCRIPTION SW2 2 PGND 3 SW1 4 ADP2503/ ADP2504 TOP VIEW (Not to scale) PVIN 5 10 FB 9 AGND 8 VIN 7 SYNC 6 EN *CONNECT PADDLE TO GND. 07475-003 VOUT 1 Figure 2. Pin Configuration Table 3. Pin Function Descriptions Pin No. 1 2 Mnemonic VOUT SW2 3 4 PGND SW1 5 PVIN 6 EN 7 SYNC 8 9 10 EP VIN AGND FB Paddle Description The output of the ADP2503/ADP2504. Connect the output capacitor between VOUT and PGND. Power Switch 2 Connection. This is the internal connection to the input PMOS and NMOS switches. Connect SW2 to the inductor with a short, wide track. Power GND. Connect the input and output capacitors and PGND pin to a PGND plane. Power Switch 1 Connection. This is the internal connection to the output PMOS and NMOS switches. Connect SW1 to the inductor with a short, wide track. Power Input. This the input to the buck-boost power switches. Place a 10 μF capacitor between PVIN and PGND as close as possible to the ADP2503/ADP2504. Enable. Drive EN high to turn on the ADP2503/ADP2504. Bring EN low to put the part into shutdown mode. The SYNC pin permits the ADP2503/ADP2504 to operate in three different modes. Normal operation: with SYNC driven low, the ADP2503/ADP2504 operates at 2.5 MHz PWM mode for heavy and medium loads, and moves to power save mode (PSM) mode for light loads. Forced PWM operation: with SYNC driven high, the ADP2503/ADP2504 operates at fixed 2.5 MHz PWM mode for all load conditions. SYNC mode: to synchronize the ADP2503/ADP2504 switching to an external signal, drive this pin with a clock between 2.2 MHz and 2.8 MHz. The SYNC signal must have on and off times greater than 160 ns. Analog Power Supply. This is the supply for the ADP2503/ADP2504 internal circuitry. Analog Ground. Output Feedback. This is an input to the internal error amplifier. Connect the paddle to PGND. Rev. PrB | Page 5 of 16 ADP2503/ADP2504 Preliminary Technical Data 100 100 90 90 80 80 70 70 EFFICIENCY (%) 60 50 40 30 0.1 1 Figure 3. Efficiency vs. Output Current, PWM Mode (VOUT = 5.0 V) 0 0.001 1 Figure 6. Efficiency vs. Output Current, PSM and PWM Mode (VOUT = 3.3 V) 90 90 80 80 70 70 EFFICIENCY (%) 100 60 50 40 60 50 40 30 VIN = 5.5V VIN = 4.2V VIN = 3.6V VIN = 2.3V 10 0.01 0.1 VIN = 5.5V VIN = 4.2V VIN = 3.6V VIN = 2.3V 20 10 1 IOUT (A) 07475-104 20 0 0.001 90 90 80 80 70 70 EFFICIENCY (%) 100 40 1 Figure 7. Efficiency vs. Output Current, PWM Mode (VOUT = 2.8 V) 100 50 0.1 IOUT (A) Figure 4. Efficiency vs. Output Current, PSM and PWM Mode (VOUT = 5.0 V) 60 0.01 07475-105 30 30 60 50 40 30 VIN = 5.5V VIN = 4.2V VIN = 3.6V VIN = 2.3V 10 0.01 0.1 VIN = 5.5V VIN = 4.2V VIN = 3.6V VIN = 2.3V 20 10 1 IOUT (A) Figure 5. Efficiency vs. Output Current, PWM Mode (VOUT = 3.3 V) 07475-109 20 0 0.001 0.1 IOUT (A) 100 0 0.001 0.01 07475-108 0.01 VIN = 5.5V VIN = 4.2V VIN = 3.6V VIN = 2.3V 10 IOUT (A) EFFICIENCY (%) 40 20 07475-103 10 EFFICIENCY (%) 50 30 VIN = 5.5V VIN = 4.2V VIN = 3.6V VIN = 2.3V 20 0 0.001 60 0 0.001 0.01 0.1 IOUT (A) 1 07475-106 EFFICIENCY (%) TYPICAL PERFORMANCE CHARACTERISTICS Figure 8. Efficiency vs. Output Current, PSM and PWM Mode (VOUT = 2.8 V) Rev. PrB | Page 6 of 16 Preliminary Technical Data ADP2503/ADP2504 50 90 45 80 40 QUIESCENT CURRENT (µA) 100 60 50 40 30 IOUT = 500mA IOUT = 100mA IOUT = 10mA 20 35 30 25 20 15 10 10 2.8 3.3 3.8 VIN (V) 4.3 4.8 07475-107 5 0 2.3 5.3 0 2.3 2.7 3.1 3.5 3.9 VIN (V) 4.3 4.7 5.1 5.5 07475-113 EFFICIENCY (%) 70 Figure 12. Quiescent Current vs. Input Voltage (VOUT = 3.3 V) Figure 9. Efficiency vs. Input Voltage (VOUT = 3.3 V) 3.35 VIN VIN = 3.0V TO 3.6V VOUT = 5.0V 3.33 VOUTA (V) SW1 3.31 4 2 3.29 SW2 3 VOUT 3.27 07475-110 07475-005 1 3.25 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 CH1 50.0mV BW CH2 1.00V BW M40.0µs A CH2 CH4 5.00V BW T 18.20% CH3 5.00V BW 1.0 IOUT (A) 3.40mV Figure 13. Line Transient, PWM Mode (VIN = 3.0 V to 3.6 V, VOUT = 5.0 V) Figure 10. Load Regulation (VIN = 3.6 V, VOUT = 3.3 V) 2.8 VIN VIN = 3.0V TO 3.6V VOUT = 3.3V 2.7 SW1 +25°C 4 2.5 2 2.4 3 +85°C VOUT 2.3 1 2.7 3.1 3.5 3.9 VIN (V) 4.3 4.7 5.1 5.5 07475-112 2.2 2.3 SW2 Figure 11. Frequency vs. Input Voltage Over Temperature (VOUT = 3.3 V) 07475-006 FREQUENCY (MHz) –40°C 2.6 CH1 50.0mV BW CH2 1.00V BW M40.0µs A CH2 CH3 5.00V BW CH4 5.00V BW T 18.20% 3.40V Figure 14. Line Transient, PWM Mode (VIN = 3.0 V to 3.6 V, VOUT = 3.3 V) Rev. PrB | Page 7 of 16 ADP2503/ADP2504 VIN Preliminary Technical Data VIN = 3.0V TO 3.6V VOUT = 2.8V SW1 SW1 4 4 2 IOUT SW2 2 3 VOUT 07475-007 1 CH1 50.0mV BW CH4 1.00V BW M40.0µs A CH2 CH3 5.00V BW CH4 5.00V BW T 18.20% VIN = 3.6V VOUT = 3.3V 07475-010 VOUT 1 CH1 100mV BW CH2 500mA Ω 3.40mV CH4 2.00V BW Figure 15. Line Transient, PWM Mode (VIN = 3.0 V to 3.6 V, VOUT = 2.8 V) M100µs A CH2 T 45.40% –115mA Figure 18. Mode Change by Load Transients, Load Rise (VOUT = 3.3 V) VIN = 3.6V VOUT = 3.3V SW1 VOUT 1 IOUT 4 2 IOUT SW1 07475-008 SW2 3 CH1 100mV BW CH2 250mA Ω M100µs A CH2 CH3 5.00V BW CH4 5.00V BW T 25.80% VIN = 3.6V VOUT = 3.3V VOUT 1 60.0mA CH1 100mV BW CH2 500mA Ω CH4 2.00V BW Figure 16. Load Transient (VIN = 3.6 V VOUT = 3.3 V, IOUT = 100 mA to 350 mA) M100µs A CH2 T 45.40% 410mA Figure 19. Mode Change by Load Transients, Load Fall (VOUT = 3.3 V) VIN = 3.6V VOUT = 3.3V 1 07475-011 2 4 SW2 VIN = 4.0V VOUT = 3.3V VOUT 3 IOUT SW1 2 4 SW1 ISW 2 4 SW2 07475-111 VOUT CH1 100mV BW CH2 250mA Ω M100µs A CH2 CH3 5.00V BW CH4 5.00V BW T 23.00% 60.0mA 07475-012 3 1 CH1 50.0mV BW CH2 250mA Ω CH3 5.00V BW Figure 17. Load Transient (VIN = 3.6 V VOUT = 3.3 V, IOUT = 10 mA to 300 mA) CH4 5.00V BW M 400ns A CH3 T 50.00% 2.40V Figure 20. Typical PWM Switching Waveform, Buck Operation (VOUT = 3.3 V) Rev. PrB | Page 8 of 16 Preliminary Technical Data SW2 ADP2503/ADP2504 VIN = 3.0V VOUT = 3.3V SW1 4 3 SW1 VOUT = 3.3V VOUT 4 1 ISW ISW 2 2 EN VOUT CH1 20.0mV BW CH2 250mA Ω CH3 5.00V BW CH4 5.00V BW M 400ns A CH4 T 50.80% CH1 2.00V BW CH2 500mAΩ BW M 100µs A CH3 T 9.400% CH3 5.00V BW CH4 5.00V BW 2.40V Figure 21. Typical PWM Switching Waveform, Boost Operation (VOUT = 3.3 V) SW2 07475-018 3 07475-013 1 2.40V Figure 24. Startup into PWM Mode (VOUT = 3.3 V, IOUT = 300 mA) VIN = 3.0V VOUT = 3.3V SW1 4 3 SW1 VOUT 4 VOUT = 3.3V 1 ISW ISW 2 2 EN VOUT CH1 20.0mV BW CH2 250mA Ω CH3 5.00V BW CH4 5.00V BW M 400ns A CH4 T 50.00% 07475-019 3 07475-027 1 CH1 2.00V BW CH2 500mAΩ BW M 100µs A CH3 T 9.400% CH3 5.00V BW CH4 5.00V BW 2.40V Figure 22. Typical PWM Switching Waveform, Buck-Boost Operation (VOUT = 3.3 V) 2.40V Figure 25. Startup into PWM Mode (VOUT = 3.3 V, IOUT = 10 mA) VIN = 3.0V VOUT = 3.3V SW1 SW2 4 3 VOUT SW1 4 VOUT = 3.3V 1 ISW 2 ISW 2 EN VOUT CH1 100mV BW CH2 1.00A Ω CH3 5.00V BW CH4 5.00V BW M 4.00µs A CH2 T 15.20% 07475-023 3 07475-015 1 CH1 2.00V BW CH2 500mAΩ BW M 100µs A CH3 T 9.400% CH3 5.00V BW CH4 5.00V BW 820mA Figure 23. Typical PSM Switching Waveform, Buck-Boost Operation (VOUT = 3.3 V) Rev. PrB | Page 9 of 16 2.40V Figure 26. Startup into PSM Mode (VOUT = 3.3 V, IOUT = 10 mA) ADP2503/ADP2504 Preliminary Technical Data THEORY OF OPERATION 1.0µH SW1 SW2 4 ADP2503/ADP2504 VIN ADP2503/ADP2504 BIASING 8 VBAT = 2.3V TO 5.5V 2 PMOS1 PVIN PMOS2 VOUT 5 1 10µF NMOS1 22µF NMOS2 2.25V SOFT START UVLO FB BAND GAP REFERENCE 10 THERMAL PROTECTION –0.5V PWM CONTROL EN EN 6 SYNC OSCILLATOR PGND AGND 3 9 07475-025 7 CS Figure 27. ADP2503/ADP2504 Block Diagram The ADP2503/ADP2504 are synchronous average currentmode switching buck-boost regulators designed to maintain a fixed output voltage VOUT from an input supply VIN that can be above, equal to, or below VOUT. When VIN is significantly greater than VOUT, the device is in buck mode: PMOS2 is always active, NMOS2 is always off and the switches PMOS1, NMOS1 consti tute a buck converter. When VIN is significantly lower than VOUT, the device is in boost mode: PMOS1 is always active, NMOS1 is always off and the switches NMOS2, PMOS2 constitute a boost converter. When VIN is in the range [VOUT − 10%; VOUT + 10%], the ADP2503/ADP2504 automatically enter the buck-boost mode. In buck-boost mode, the two operations buck (PMOS1 and NMOS1 switching in antiphase) and boost (NMOS2 and PMOS2 switching in antiphase) take place at each period of the clock. This is aimed at maintaining the regulation and keeping a minimal current ripple in the inductor to guarantee good transient performances. REVERSE CURRENT LIMIT In case of a short circuit on VOUT to a value greater than expected, the inductor current becomes negative (reverse current). The negative peak value is limited to 1.1 A by deactivating the switch PMOS2. POWER SAVE MODE When the SYNC pin is low, the ADP2503/ADP2504 can operate in power save mode (PSM). In this mode, when the load current becomes lower than 75 mA nominally at VIN = 3.6 V, the controller pulls up VOUT and then halts the switching regime until VOUT goes back to a restart value. Then VOUT is pulled up again for a new cycle. This minimizes the switching losses at light load. When the load rises above 150 mA, the ADP2503/ADP2504 revert back to fixed PWM mode. This results in about 75 mA of hysteresis between PSM and fixed PWM, preventing oscillations between these two modes. SOFT START When the ADP2503/ADP2504 are started, VOUT is ramped from 0 V to its final programmed value in 200 μs (typ). This limits the inrush current to less than 600 mA for a nominal output capacitor of 20 μF. Because the VOUT start-up slope is constant, the inrush current becomes larger if the output capacitor is made larger. Rev. PrB | Page 10 of 16 Preliminary Technical Data ADP2503/ADP2504 ENABLE THERMAL SHUTDOWN The device starts operation with soft start when the EN pin is brought high. Pulling the EN pin low forces the device into shutdown, with a typical shutdown current of 0.2 μA. When the junction temperature, TJ, exceeds 150°C typical, the device goes into thermal shutdown. In this mode, the power switches are turned off. The device resumes operation when the junction temperature again falls below 125°C typical. In this mode, the PMOS power switches are turned off, the NMOS power switches are turned on, and the control circuitry is not enabled. For proper operation, the EN pin must be terminated and must not be left floating. UNDERVOLTAGE LOCKOUT The undervoltage lockout circuit prevents the device from oper ating incorrectly at low input voltages. It prevents the converter from turning on the power switches under undefined conditions and therefore, prevents deep discharge of the battery supply. VIN must be greater than 2.25 V to enable the converter. During operation, if VIN drops below 2.18 V, the ADP2503/ADP2504 are disabled until the supply exceeds the UVLO rising threshold. SHORT CIRCUIT PROTECTION When the nominal inductor peak current value of 1.5 A is reached, the ADP2503/ADP2504 first switch off the NMOS2 transistor if it was active. If the current thereafter continues to increase by an extra amount of 200 mA, the PMOS1 transistor is also switched off. This operation is reversible when the short circuit stops. It allows the inductor current ripple to be mini mized close to 1.5 A and, thus, the controller to restore VOUT even if a high load current is maintained after the short circuit. Rev. PrB | Page 11 of 16 ADP2503/ADP2504 Preliminary Technical Data APPLICATIONS INFORMATION INDUCTOR SELECTION Table 4. Sample of Recommended Inductors The high 2.5 MHz switching frequency of the ADP2503/ ADP2504 allows for minimal output voltage ripple, while minimizing inductor size and cost. Careful inductor selection also optimizes efficiency and reduces electromagnetic interfe rence (EMI). The selection of the inductor value determines the inductor current ripple and loop dynamics. ΔI L , peak (Buck) = VOUT × (VIN − VOUT ) ΔI L , peak (Boost) = VIN × f OSC × L (VOUT − V IN ) VOUT × VIN f OSC × L where fOSC is the switching frequency (typically 2.5 MHz), and L is the inductor value in henries. Vendor Toko Toko Toko Murata Murata TDK TDK Coilcraft Coilcraft Part No. DE2810C DE2810C MDT2520-CN LQM2HP-G0 LQM2HP-G0 CPL2512T CPL2512T LPS3010 LPS3010 DCR (mΩ) 55 60 100 55 70 90 120 85 120 ΔVOUT , peak (Buck) = ΔVOUT , peak (Boost) = VOUT × (V IN − VOUT ) V IN × 8 × L × ( f OSC )2 × C OUT I LOAD × (VOUT − V IN ) C OUT × VOUT × f OSC If the ADP2503/ADP2504 are operating in buck mode, the worst-case voltage ripple occurs for the highest input voltage, VIN. If the ADP2503/ADP2504 are operating in boost mode, the worst-case voltage ripple occurs for the lowest input voltage, VIN. ⎞ 1 ⎟× ⎟ η ⎠ where η is efficiency (assume η ≈ 0.85 to 0.90). The saturation current rating of the inductor must be at least IIN(MAX) + ΔILOAD/2. Ceramic multilayer inductors can be used with lower current designs for a reduced overall solution size and dc resistance (DCR). These are available in low profile packages. Care must be taken as these derate quickly as the inductor value is increased especially at higher operating temperatures. The maximum voltage overshoot, or undershoot is inversely proportional to the value of the output capacitor. To ensure stability and excellent transient response, it is recommended to use a minimum of 22 μF X5R 6.3 V or 2 × 10 μF X5R 6.3 V capacitors at the output. The effective capacitance (includes temperature, dc bias effects) needed for stability is 14 μF. Ferrite core inductors have good core loss characteristics as well as reasonable dc resistance. A shielded ferrite inductor reduces the EMI generated by the inductor. Table 5. Recommended Output Capacitors Value 2 × 10 μF, 6.3 V 2 × 10 μF, 6.3 V 22 μF, 6.3 V 22 μF, 6.3 V 22 μF, 10 V 10 μF, 10 V Dimensions L ×W × H (mm) 2.8 × 2.8 × 1.0 2.8 × 2.8 × 1.0 2.5 × 2 × 1.2 2.5 × 2 × 1 2.5 × 2 × 1 2.5 × 1.5 × 1.2 2.5 × 1.5 × 1.2 3.0 × 3.0 × 0.9 3.0 × 3.0 × 0.9 The output capacitor selection determines the output voltage ripple, transient response and the loop dynamics of the ADP2503/ADP2504. The output voltage ripple for a given output capacitor is given by The inductor peak current is at the maximum in boost mode. To determine the actual maximum inductor current in boost mode, the input dc current should be estimated. Vendor Murata TDK Murata TDK TDK Murata ISAT (A) 1.7 1.5 1.8 1.6 1.5 1.5 1.2 1.7 1.3 Output Capacitor Selection A larger inductor value reduces the current ripple (and therefore peak inductor current), but is physically larger in size with increased dc resistance. Inductor values between 1 μH and 1.5 μH are usually suggested. The maximum inductor value to ensure stability is 2.0 μH. For increased efficiency with the ADP2504, it is suggested a 1.5 μH inductor be used. ⎛V I IN ( MAX) = I LOAD( MAX) × ⎜⎜ OUT ⎝ VIN Value (μH) 1.2 1.5 1 1 1.5 1.0 1.5 1.0 1.5 Part No. GRM188R60J106ME47 C1608JB0J106K GRM21BR60J226ME39 C2012X5R0J226M C3216X5R1A226K GRM21BR71A106KE51L Rev. PrB | Page 12 of 16 Dimensions L × W × H (mm) 1.6 × 0.8 × 0.8 (2) 1.6 × 0.8 × 0.8 (2) 2 × 1.25 × 1.25 2 × 1.25 × 1.25 2 × 1.25 × 1.25 2 × 1.25 × 1.25 (2) Preliminary Technical Data ADP2503/ADP2504 Input Capacitor Selection Table 6. Recommended Input Capacitors The ADP2503/ADP2504 require an input capacitor to filter noise on the VIN pin, and provide the transient currents while maintaining constant input and output voltage. A 10 μF X5R/ X7R ceramic capacitor rated for 6.3 V is the minimum recom mended input capacitor. Increased input capacitance reduces the amplitude of the switching frequency ripple on the battery. Because of the dc bias characteristics of ceramic capacitors, a 0603, 6.3 V X5R/X7R, 10 μF ceramic capacitor is preferable. Vendor Murata TDK Rev. PrB | Page 13 of 16 Value 10 μF, 6.3 V 10 μF, 6.3 V Part No. GRM188R60J106ME47 C1608JB0J106K Dimensions L×W×H (mm) 1.6 × 0.8 × 0.8 1.6 × 0.8 × 0.8 ADP2503/ADP2504 Preliminary Technical Data PCB LAYOUT GUIDELINES • Poor layout can affect ADP2503/ADP2504 performance, causing electromagnetic interference (EMI) and electromagnetic compatibility (EMC) performance, ground bounce, and voltage losses. Poor layout can also affect regulation and stability. A good layout is implemented using the following rules: • • Place the inductor, input capacitor, and output capacitor close to the IC using short tracks. These components carry high switching frequencies and large tracks act like antennas. ADP2503/ADP2504 EVALUATION BOARD 10mm L1 VIN VOUT J1 J3 8mm C1 C2 C3 JP1 U1 R3 JP1 C4 PGND PGND J4 J2 TP2 TP1 R1 R2 J6 1 J5 1 EN SYNC Figure 28. ADP2503/ADP2504 Evaluation Board Rev. PrB | Page 14 of 16 07475-026 • Route the output voltage path away from the inductor and SW node to minimize noise and magnetic interference. Maximize the size of ground metal on the component side to help with thermal dissipation. Use a ground plane with several vias connecting to the component side ground to further reduce noise interference on sensitive circuit nodes. Preliminary Technical Data ADP2503/ADP2504 OUTLINE DIMENSIONS 0.30 0.23 0.18 0.50 BSC 10 6 PIN 1 INDEX AREA *EXPOSED PAD (BOTTOM VIEW) 0.50 0.40 0.30 5 TOP VIEW 2.48 2.38 2.23 0.80 MAX 0.55 NOM 0.80 0.75 0.70 1 0.05 MAX 0.02 NOM SEATING PLANE 1.74 1.64 1.49 PIN 1 INDICATOR (R 0.20) *PADDLE CONNECTED TO GND. 0.20 REF 060408-B 3.00 BSC SQ Figure 298. 10-Lead Lead Frame Chip Scale Package [LFCSP_WD] 3 mm × 3 mm Body, Very Very Thin, Dual Lead (CP-10-9) Dimensions shown in millimeters ORDERING GUIDE Model ADP2503ACPZ-2.8-R71 ADP2503ACPZ-3.3-R71 ADP2503ACPZ-3.5-R71 ADP2503ACPZ-4.2-R71 ADP2503ACPZ-4.5-R71 ADP2503ACPZ-5.0-R71 ADP2504ACPZ-2.8-R71 ADP2504ACPZ-3.3-R71 ADP2504ACPZ-3.5-R71 ADP2504ACPZ-4.2-R71 ADP2504ACPZ-4.5-R71 ADP2504ACPZ-5.0-R71 1 Voltage 2.8 V 3.3 V 3.5 V 4.2 V 4.5 V 5.0 V 2.8 V 3.3 V 3.5 V 4.2 V 4.5 V 5.0 V Maximum Current 0.6 A 0.6 A 0.6 A 0.6 A 0.6 A 0.6 A 1A 1A 1A 1A 1A 1A Temperature Range −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C Package Description 10-Lead Lead Frame Chip Scale Package [LFCSP_WD] 10-Lead Lead Frame Chip Scale Package [LFCSP_WD] 10-Lead Lead Frame Chip Scale Package [LFCSP_WD] 10-Lead Lead Frame Chip Scale Package [LFCSP_WD] 10-Lead Lead Frame Chip Scale Package [LFCSP_WD] 10-Lead Lead Frame Chip Scale Package [LFCSP_WD] 10-Lead Lead Frame Chip Scale Package [LFCSP_WD] 10-Lead Lead Frame Chip Scale Package [LFCSP_WD] 10-Lead Lead Frame Chip Scale Package [LFCSP_WD] 10-Lead Lead Frame Chip Scale Package [LFCSP_WD] 10-Lead Lead Frame Chip Scale Package [LFCSP_WD] 10-Lead Lead Frame Chip Scale Package [LFCSP_WD] Z = RoHS Compliant Part. Rev. PrB | Page 15 of 16 Package Option CP-10-9 CP-10-9 CP-10-9 CP-10-9 CP-10-9 CP-10-9 CP-10-9 CP-10-9 CP-10-9 CP-10-9 CP-10-9 CP-10-9 Branding L9Y L9Z LAP LA0 LA1 LA2 L9T L85 LAN L9U L9V L9W ADP2503/ADP2504 Preliminary Technical Data NOTES ©2008 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. PR07475-0-8/08(PrB) Rev. PrB | Page 16 of 16