AOZ6135 High Performance, Low RON, 1Ω SPDT Analog Switch General Description Features The AOZ6135 is a high performance single-pole double-throw (SPDT), low power, TTL-compatible bus switch. ● SC-70 6-Lead Package ● 1.65V to 5.5V VCC operation ● 1Ω connection between ports ● Break-before-make switching The AOZ6135 can handle analog and digital signals. Signals with voltages up to VCC (1.65V to 5.5V) can be transmitted in either direction. When the Select pin is LOW, B0 is connected to the output A pin. When the Select pin is HIGH, B1 is connected to the output A pin. The path that is open will have a high-impedance state with respect to the output. Break-before-make is guaranteed. Typical Application AOZ6135 External MIC MIC Pre-Amp CODEC Internal MIC Rev. 1.1 April 2010 www.aosmd.com Page 1 of 11 AOZ6135 Ordering Information Part Number Ambient Temperature Range Package Environmental AOZ6135HI -40°C to +85°C SC-70-6 RoHS Compliant Green Product AOS Green Products use reduced levels of Halogens, and are also RoHS compliant. Please visit www.aosmd.com/web/quality/rohs_compliant.jsp for additional information. Pin Configuration B1 1 6 S GND 2 5 Vcc B0 3 4 A SC-70-6 (Top View) Truth Table Logic S Input Function 0 B0 Connected to A 1 B1 Connected to A Rev. 1.1 April 2010 www.aosmd.com Page 2 of 11 AOZ6135 Absolute Maximum Ratings Exceeding the Absolute Maximum ratings may damage the device. Symbol Parameter VCC Rating Supply Voltage -0.5V to +6V (1) Switch Voltage VS -0.5V to VCC (1) VIN Input Voltage IIK Minimum Input Diode Current(2) -50mA ISW Switch Current 200mA Peak Switch Current (Pulsed at 1ms, <10% Duty Cycle) 400mA ISWPEAK -0.5V to VCC Storage Temperature Range TSTG -65°C to +150°C Maximum Junction Temperature TJ 180mW Human Body Model (JESD22A-114E) 8000V SC-70-6 Power Dissipation at 85°C PD ESD +150°C (3) Recommend Operating Ratings The device is not guaranteed to operate beyond the Maximum Operating Ratings. Symbol VCC Parameter Supply Voltage 1.65V to +5.5V Voltage(4) VIN Control Input VSW Switch Input Voltage TA Rating 0V to VCC 0V to VCC Operating Temperature -40°C to +85°C Notes: 1. Signals on A, or B or S exceeding V+ will be clamped by internal diodes. Limit forward diode current to maximum current ratings. 2. Negative current should not exceed minimum negative value. 3. All leads welded or soldered to PC Board. 4. Unused inputs must be held HIGH or LOW. They may not float. Rev. 1.1 April 2010 www.aosmd.com Page 3 of 11 AOZ6135 Electrical Characteristics Unless otherwise indicated, specifications indicate a temperature range of -40°C to +85°C Symbol Parameter Test Conditions VCC (V) Min. 1.65 to 2.7 1.0 2.7 to 3.6 1.5 4.5 to 5.5 2.0 Typ.(1) Max. Units DC CHARACTERISTICS VIH VIL RON RFLAT ΔRON Input Voltage High Input Voltage Low On Resistance On Resistance Flatness On Resistance Matching Between Channels V 1.65 to 2.7 0.4 2.7 to 3.6 0.6 4.5 to 5.5 0.8 IOUT =100mA, B0 or B1 = 0V, 1.5V, 2.5V, 3.5V, 3.75V, 4.5V 4.5 0.6 1.2 IOUT = 100mA, B0 or B1 = 0V, 1.5V, 2V, 2.7V 2.7 1.0 1.5 IOUT =100mA, B0 or B1 = 0V, 1.25V, 1.5V, 1.8V 1.8 3.0 6.0 IOUT =100mA, B0 or B1 = 0V to VCC 4.5 0.2 2.7 0.3 1.8 2.5 4.5 0.03 IOUT =100mA, B0 or B1 = 1.5V V Ω Ω 0.15 Ω IOUT =100mA, B0 or B1 = 3.5V Input Leakage Current VIN = 0V or VCC 1.95 to 5.5 ±1.0 µA IB(off) Off Stage Switch Leakage A = 1V, 4.5V, B0 or B1 = 4.5V, 1V 1.95 to 5.5 ±20 nA IA(on) On State Switch Leakage A = 1V, 4.5V, B0 or B1 = 4.5V, 1V or floating 1.95 to 5.5 ±40 nA IIN POWER SUPPLY VCC Power Supply Range ICCQ Quiescent Supply Current ICCT Increase in ICC per Input Rev. 1.1 April 2010 1.65 to 5.5 VIN = 0V or VCC, IOUT = 0V 5.5 VIN = 1.8V 5.5 VIN = 2.6V www.aosmd.com 1.65 5.5 V 0.5 µA 30 40 µA 18 25 Page 4 of 11 AOZ6135 Electrical Characteristics (Continued) Unless otherwise indicated, specifications indicate a temperature range of -40°C to +85°C Symbol Test Conditions VCC (V) B0 or B1 = 1.5V, RL = 50Ω, CL = 35pF Parameter Min. Typ.(1) Max. Units 2.7 to 3.6 60 65 ns 4.5 to 5.5 35 40 2.7 to 3.6 20 30 4.5 to 5.5 15 20 AC CHARACTERISTICS tON tOFF tBBM Q Turn-On Time Turn-Off Time B0 or B1 = 1.5V, RL = 50Ω, CL = 35pF Break-Before-Make Time Charge Injection 1.65 to 1.95 CL = 1.0nF, VGE = 0V, RGEN = 0Ω 20 2.3 to 2.7 20 3.0 to 3.65 20 4.5 to 5.5 20 4.5 to 5.5 75 2.7 to 3.6 50 ns ns pC ANALOG SWITCH CHARACTERISTICS OIRR Off Isolation RL = 50Ω, f = 1MHz 2.7 to 5.5 -60 dB XTALK Crosstalk RL = 50Ω, f = 1MHz 2.7 to 5.5 -60 dB BW -3dB Bandwidth RL = 50Ω 2.7 to 5.5 180 MHz THD Total Harmonic Distortion VIN = 2Vpk-pk, f = 20Hz to 20kHz 2.7 to 5.5 0.002 % CAPACITANCE CIN Control Pin Capacitance f = 1MHz, Vbias = 1.5V 0.0 3.0 pF COFF B Port Off Capacitance f = 1MHz, Vbias = 1.5V 4.5 7.0 pF CON A Port Capacitance When Switch Enable f = 1MHz, Vbias = 1.5V 4.5 40.0 pF Notes: 1. Typical values are for design aid only, not guaranteed nor subject to production testing. Rev. 1.1 April 2010 www.aosmd.com Page 5 of 11 AOZ6135 AC Loading and Waveforms Vcc Control Input VOUT VB RL 50Ω t Vcc R = t F = 2.5nS 50% 0V t OFF CL 35pF VOUT Switch Output GND 0.9 x VOUT 0.9 x VOUT 0 t ON Logic input waveform are inverted for switches with opposite logic sense CL Includes Fixture and Stray Capacitance Figure 1. Turn-On/Turn-Off Timing Vcc Vcc BN BN A A + + + S S + + GND Figure 2. Off State Leakage Current GND Figure 3. On State Leakage Current Vcc B0 VB Vcc A B1 VOUT RL 50 Ω S CL 35pF Control Input 50% 0V t R = t F = 2.5nS VOUT GND 0.9 x VOUT tD CL Includes Fixture and Stray Capacitance Figure 4. Break-Before-Make Timing Network Analyzer Vcc B0 VIN VOUT 50Ω A Network Analyzer Vcc B0 50Ω Source Signal B1 A VIN VOUT 50Ω Source Signal 50Ω S Vcc or 0V + S 50Ω 50Ω GND GND Figure 6. Crosstalk Figure 5. Off Isolation Rev. 1.1 April 2010 Vcc or 0V + www.aosmd.com Page 6 of 11 AOZ6135 AC Loading and Waveforms (Continued) Vcc BN A + S + GND Figure 7. On State Resistance Vcc R GEN A V GEN VOUT VOUT B 0 or B 1 Input Control CL IN Δ VOUT OFF OFF ON S GND ON OFF IN OFF Q = (ΔVOUT)(CL) Figure 8. Charge Injection Vcc 10nF Vcc Network Analyzer 50Ω BN A A S Capacitance Meter f = 1MHz B 0 or B1 Source Signal 0V or Vcc S + 50Ω GND GND Figure 9. ON/Off Capacitance Measurement Figure 10. Bandwidth Vcc Audio Analyzer 600 Ω A BN CL Source Signal S + 600 Ω GND CL Includes Fixture and Stray Capacitance Figure 11. Harmonic Distortion Rev. 1.1 April 2010 www.aosmd.com Page 7 of 11 AOZ6135 Package Dimensions, SC70-6L D Gauge Plane 0.15mm e1 θ L E1 E e c b A2 A .010mm A1 Dimensions in millimeters RECOMMENDED LAND PATTERN 1.95 0.65 0.35 0.65 UNIT: mm Symbols A A1 A2 b Min. c D E e e1 0.08 1.85 1.80 E1 L θ 1.1 0.26 0° 0.00 0.7 0.15 Nom. — — 0.9 — Max. 1.10 0.10 1.00 0.30 — 0.22 2.10 2.15 2.30 2.40 0.65 BSC 1.30 BSC 1.30 0.36 4° 1.4 0.46 8° Dimensions in inches Symbols A A1 A2 b Min. 0.00 0.028 0.006 c D E e e1 0.003 0.073 0.071 E1 L θ 0.043 0.010 0° Nom. — — 0.035 — Max. 0.043 0.004 0.039 0.012 — 0.009 0.083 0.085 0.091 0.094 0.026 BSC 0.051 BSC 0.051 0.014 4° 0.055 0.018 8° Notes: 1. All dimensions are in millimeters. 2. Dimensions are inclusive of plating 3. Package body sizes exclude mold flash and gate burrs. Mold flash at the non-lead sides should be less than 3 mils. 4. Die is facing up for mold and facing down for trim/form; i.e., reverse trim/form. 5. Dimension L is measured in gauge plane. 6. Controlling dimension is millimeter, converted inch dimensions are not necessarily exact. Rev. 1.1 April 2010 www.aosmd.com Page 8 of 11 AOZ6135 Tape and Reel Dimensions, SC70-6L Carrier Tape P1 D1 P2 T E1 E2 E B0 K0 A0 D0 P0 Feeding Direction UNIT: mm Package SC-70, 6L (8mm) A0 2.40 ±0.10 B0 2.40 ±0.10 K0 1.19 ±0.10 D0 1.00 Min. D1 1.55 ±0.05 E 8.00 ±0.30 Reel E1 1.75 ±0.10 E2 3.50 ±0.05 P0 4.00 ±0.10 P1 4.00 ±0.10 P2 2.00 ±0.05 T 0.25 ±0.05 W1 S G N M K V R H W W N Tape Size Reel Size M 8mm ø180 ø180.00 ø60.50 9.00 ±0.30 ±0.50 W1 11.40 ±1.00 H K ø13.00 10.60 +0.50/-0.20 S 2.00 ±0.50 G ø9.00 R 5.00 V 18.00 Leader/Trailer and Orientation Trailer Tape 300mm min. or 75 empty pockets Rev. 1.1 April 2010 Components Tape Orientation in Pocket www.aosmd.com Leader Tape 500mm min. or 125 empty pockets Page 9 of 11 AOZ6135 Part Marking AOZ6135HI AWL Part Number Code Assembly Lot & Location Code Week & Year Code Rev. 1.1 April 2010 www.aosmd.com Page 10 of 11 AOZ6135 Revision History Revision Revised Item Rev. 1.0 Initial release Rev. 1.1 IccT Max Limit relaxed after production data were collected This datasheet contains preliminary data; supplementary data may be published at a later date. Alpha & Omega Semiconductor reserves the right to make changes at any time without notice. LIFE SUPPORT POLICY ALPHA & OMEGA SEMICONDUCTOR PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. Rev. 1.1 April 2010 2. A critical component in any component of a life support, device, or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. www.aosmd.com Page 11 of 11