OX-221-9100-20M000 OCXO OX-221-9100-20M000 Nominal frequency (f0) 20 MHz Performance Specifications Frequency stabilities Parameter Min Typical Max Units Condition -40...85 C include: Temp. Stab, supply, load stab, initial, 20 years aging ◦ Over all (df/f0) -4.6 +4.6 ppm -5 +5 ppb -40...85◦ C -200 +200 ppb @25 ◦ C vs. supply voltage change (df/f) -2 +2 ppb static; 3.3 V ±5 % vs. load change (df/f)) -2 +2 ppb static; Load +5 % -5 % vs. aging / daily (df/f) -1 +1 ppb after 30 days ; @ 25 ◦ C vs. aging / year (df/f) -100 +100 ppb after 30 days ; @ 25 ◦ C -1 +1 vs. operating temp. range (df/f@25◦ C) initial tolerance (df/f0) Holdover/Drift ppb ppb 10 [pk-pk] S3E compliant according GR1244 Note: over 24 hours and ±2.8◦ C over 24 hours; -40...85◦ C RF output Parameter Min Signal Typical Max Units Condition LVCMOS Load 13.5 15 16.5 pF Rise Time 5 ns @10 to 90 %Vout Fall Time 5 ns @90 to 10 %Vout 55 % @1.65 V 0.4 V Fan out Duty cycle 45 V Low V High 2.4 V Sub Harmonics -70 dBc Spurious -90 dBc Page 1 of 6 Vectron International • http://www.vectron.com • modified 2016-11-11 index: 8 • printed 2017-12-15 Supply voltage Parameter Supply voltage (Vs) Min Typical Max 3.14 3.3 Units Condition 3.47 V Current consumption steady state 400 700 mA mA @ Vsnom & 25 ◦ C @ Vsnom & -40 ◦ C Current consumption during warm up 1200 mA @ Vs Additional Parameters Parameter Min Typical Max Units Condition 5 min @ 25 ◦ C to final frequency dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz psec (RMS) @1Hz @10Hz @100Hz @1kHz @10kHz @100kHz Warm up time Phase Noise -80 -113 -140 -154 -157 -159 Jitter 0.3 MTIE 0.1 0.9 5 15 TDEV Additional information Processing & Packing ns ns ns ns @ 12kHz to 5MHz 1.0 sec 10.0 sec 100.0 sec 1000.0 sec 0.003 ns 1s 0.04 ns 10 s 0.5 ns 100 s wander generation tdev & mtie at 1 mHz constant temp: meets GR-1244 mask wander generation tdev & mtie at 1 mHz variable temp: meets GR-1244 mask handling&processing note Additional Environmental Conditions Parameter RoHS compliance Description 100% RoHS 6 compliant Washable washable device ESD HBM JESD22-A114F Class 1C - 10* 2000V Mechanical Shock MIL-STD-202 Meth 213B Cond. C - 100g 6ms 6 shocks in each direction Vibration, Sine JESD22-B103 Cond.2 - 10g 10-2000Hz 4x in each 3 axis 4min sweep time Moisture Sen. Level JESD22-A113-B - only if > MSL 1 Solderabiltiy High temp operating life(HTOL) J-STD-002C Cond. A, Trough hole device; Cond.B, SMD ( correspond to MIL-STD-883 Meth 2003) - 255◦ C (diving Time 5 ±0,5sec.) Dip&Look with 8h damp pre-treatment: solder wetting >95% MIL-STD-202 Meth108A Cond C - 1000h @ 105◦ C under voltage Low temp operating life(LTOL) IEC 60068-2-1 Cond. Ae - Ta= -40◦ C, >1000 hours with bias for OCXO Reflow Simulation Test MIL-STD-202G Meth 210F Cond. K - Total 3x Lead free profile (for SMD) Temperature Cycling MIL-STD-883G Meth.1010.8 Cond.B - 1000cycles -55/+125◦ C; cycle time 30 min. Page 2 of 6 Vectron International • http://www.vectron.com • modified 2016-11-11 index: 8 • printed 2017-12-15 Absolute Maximum Ratings Parameter Min Typical Max Supply voltage (Vs) Units 5.5 Operable temperature range -40 Storage temperature range -40 Condition V +85 ◦ C +85 ◦ C Enclosure G275 0,2 25,4 0,2 22 0,1 17,8 0,1 17,8 7,62 H 23,4 0,25 7,62 Co- Planarity spec ( 0,1mm) 3,4 0,1 7 6 5 4 Padvorschlag land pattern recommendation top view 1 2,7 2 3 all units in mm Enclosure Info Parameter Type Description G275D Height 12.1 mm Weight 9g Page 3 of 6 Vectron International • http://www.vectron.com • modified 2016-11-11 index: 8 • printed 2017-12-15 Enclosure Info Parameter Pin Connections Description 1: I.C. (Do not connect) 2: N.C. 3: Vs (supply voltage input) 4: RF-Output 5: N.C. 6: N.C. 7: GND Marking OX-221-9100 20,000 MHz Ser.No. AYYWW * * pin-1 marking Package cover material Metal Package base material Metal Solder profile TP: max 260°C (@ solder joint, customer board level) Tp: max: 10…30 sec Additional Information: This SMD oscillator has been designed for pick and place reflow soldering SMD oscillators must be on the top side of the PCB during the reflow process. Page 4 of 6 Vectron International • http://www.vectron.com • modified 2016-11-11 index: 8 • printed 2017-12-15 Standard shipping method K Lage im Gurt Position in tape Pin1 A 4.0 1.75±0.1 W B XXXXX XXXXX Abwickelrichtung Unwinding direction B R 0.7 5 A P A ±0.05 0.20 Schnitt A - A B Bei W < 32mm nur obere Lochreihe vorhanden if W < 32mm only upper hole line existent Schnitt B - B Maßangaben in mm: Dimension in mm: A, B und K Maße von Bauelement abhängig A, B und K are dependent uppon component dimensions Fertigungstoleranzen entsprechen der DIN IEC 286-3 production tolerance complying DIN IEC 286-3 All dimensions in millimeters unless otherwise stated Tape Info Tape width W [mm] Quantity per meter Quantity per reel P [mm] A [mm] B [mm] K [mm] 44 35.7 175 28 22.5 25.9 12.8 W2 D N A C W1 B Reel Info A [mm] B [mm] Size C [mm] D [mm] N [mm] W1 [mm] W2 [mm] 330 1.5 13 20.2 100 45.5 49.1 Page 5 of 6 Vectron International • http://www.vectron.com • modified 2016-11-11 index: 8 • printed 2017-12-15 Notes: Unless otherwise stated all values are valid after warm-up time and refer to typical conditions for supply voltage, frequency control voltage, load, temperature (25◦ C). Subject to technical modification. For Additional Information, Please Contact USA: Europe: Asia: Vectron International 267 Lowell Road, Suite 102 Hudson, NH 03051 Tel: 1.888.328.7661 Fax: 1.888.329.8328 Vectron International Landstrasse, D-74924 Neckarbischofsheim, Germany Tel: +49 (0) 7268.801.100 Fax: +49 (0) 7268.801.282 Vectron International 68 Yin Cheng Road(C), 22nd Floor One LuJiaZui Pudong, Shanghai 200120, China Tel: +86 21 6194 6886 Fax: +86 21 6194 6699 Disclaimer Vectron International reserves the right to make changes to the product(s) and or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Page 6 of 6 Vectron International • http://www.vectron.com • modified 2016-11-11 index: 8 • printed 2017-12-15 Appendix List of appendices Appendix_OX-221-9100_20M00 Appendix Page I of III Vectron International • http://www.vectron.com II Typical Performance Data Typical MTIE OX-221-9100-20M00 1E-06 1E-07 MTIE [s] 1E-08 1E-09 1E-10 1E-11 1E-12 1E-01 1E+00 1E+01 1E+02 1E+03 1E+04 1E+05 tau [s] Telcordia GR-1244 Fig 5-5 no Filter 0,3mHz 1mHz 3mHz Typical TDEV OX-221-9100-20M00 1E-07 1E-08 TDEV [s] 1E-09 1E-10 1E-11 1E-12 1E-13 1E-01 1E+00 1E+01 1E+02 1E+03 1E+04 1E+05 tau [s] Telcordia GR-1244 Fig 5-4 no Filter 0,3mHz 1mHz 3mHz Filtered (0.3mHz, 1mHz,3mHz) curves are simulated base on measured frequency / Phase data Appendix Page II of III Vectron International • http://www.vectron.com Typical Phase Noise and Jitter OX-221-9100-20M000 Appendix Page III of III Vectron International • http://www.vectron.com