Series AM15CW-Z 15Watt | DC-DC Converter FEATURES: • • • • • • • • • • Ultra compact footprint 1”x1” Ultra-wide Input Range 4:1 1600 VDC Isolation Remote ON/OFF Function No Minimum Load Required Adjustable Output Voltage Operating Temperature -40ºC to +85ºC Over Current and Over Voltage Protection Efficiency up to 89% RoHS Compliant CE Models Single output Model AM15CW-2403SZ AM15CW-2405SZ AM15CW-2412SZ AM15CW-2415SZ AM15CW-4803SZ AM15CW-4805SZ AM15CW-4812SZ AM15CW-4815SZ Input Voltage (V) Output Voltage (V) 9-36 9-36 9-36 9-36 18-75 18-75 18-75 18-75 3.3 5 12 15 3.3 5 12 15 Input Voltage (V) Output Voltage (V) Output Current max (A) 4 3 1.3 1 4 3 1.3 1 Isolation (VDC) Efficiency (%) 1600 1600 1600 1600 1600 1600 1600 1600 86 87 88 89 84 86 87 88 Isolation (VDC) Efficiency (%) 1600 1600 1600 1600 1600 1600 85 88 89 84 87 88 Models Dual output Model AM15CW-2405DZ AM15CW-2412DZ AM15CW-2415DZ AM15CW-4805DZ AM15CW-4812DZ AM15CW-4815DZ 9-36 9-36 9-36 18-75 18-75 18-75 Output Current max (A) ±5 ±12 ±15 ±5 ±12 ±15 ±1.5 ±0.625 ±0.5 ±1.5 ±0.625 ±0.5 NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. Input Specifications Parameters Voltage range Filter Start up time Absolute Maximum Rating Peak Input Voltage time On/Off control No load current Under voltage lockout Input reflected ripple current www.aimtec.com F 051e R11 Nominal Typical 24 48 9-36 18-75 Maximum Units VDC π Nominal Vin with constant resistive load 24 Vin 48 Vin ms 50 VDC 100 100 ms ON –3 to 12VDC (or open) ; OFF – 0 to 1.2VDC or short pin 2 to pin 3; OFF idle current – 5mA 15 mA 24 Vin ON/OFF 8.5 /7 VDC 48Vin ON/OFF 17/15 20 mA p-p Tel: +1 514 620 2722 1 of 4 20 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM15CW-Z 15Watt | DC-DC Converter Isolation Specifications Parameters Tested I/O voltage Case to Input Case to Output Resistance Capacitance Conditions Typical 3 sec 3 sec 3 sec 1600 1600 1600 >1000 Maximum Units 1200 VDC VDC VDC MOhm pF Maximum Units Output Specifications Parameters Conditions Typical Voltage accuracy Cross Regulation (Dual Output Models) Over voltage protection Over current protection Short Circuit protection Short circuit restart Line voltage regulation Load voltage regulation (Single) Load voltage regulation (Dual) Temperature coefficient Ripple & Noise Voltage adjustment range 25% load on one output - 100% load on second load Zener Diode Clamp Full Load HL-LL 0% to 100% load 0% to 100% balanced load 20MHz Bandwidth Trim - Single output models only ±1 % ±5 % 120 170 Continuous Auto-Recovery ±0.2 ±0.5 ±1 ±0.02 100 10 % % % % % %/oC mV p-p % General Specifications Parameters Conditions Switching frequency Operating temperature Storage temperature Maximum case temperature Derating Cooling Humidity Case material Weight Dimensions (L x W x H) MTBF Maximum soldering temperature Transient recovery time Transient recovery deviation Typical 100% load With derating above +55°C -40 to +125 Maximum 375 -40 to +85 100 2.6 Free air convection 95 Nickel-coated copper 18 1.00 x 1.00 x 0.40 inches 25.40 x 25.40 x 10.16 mm > 560,000 hrs (MIL-HDBK -217F, Ground Benign, t=+25oC) 1.5mm from case for 10 sec 260 Load step change 75% to 50% to 25% 250 Load step change 75% to 50% to 25% ±3 Units KHz o C o C o C %/ oC % RH g o C µS % Safety Specifications Parameters Agency Approvals Standards www.aimtec.com F 051e R11 CE EN 55022 Class A EN 61000-4-2 Perf. Criteria A EN 61000-4-3 Perf. Criteria A EN 61000-4-4 Perf. Criteria A (external 220uF/100V cap required) EN 61000-4-5 Perf. Criteria A (external 220uF/100V cap required) EN 61000-4-6 Perf. Criteria A EN 61000-4-8 Perf. Criteria A NOTE: also designed to meet IEC/EN 60950-1 Tel: +1 514 620 2722 2 of 4 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM15CW-Z 15Watt | DC-DC Converter Pin Out Specifications Single + V input - V input On/Off Control + V output Trim - V output Pin 1 2 3 4 5 6 Dual + V input - V input On/Off Control + V output Common - V output Dimensions Trimming Bottom View Top View 10.16 2.54 (0.40) (0.10) 10.16 (0.40) 25.40 (1.00) 5 4 6 +V Output Trim -V Output +V -V Input Input CTRL 1 10.16 (0.40) 2 3 5.08 7.62 (0.20) (0.30) Side View Printed Face 2.54 (0.10) 1.00 (0.39) Derating Free Air Convection 55º C Output Power (%) 100 80 Safe Operating Area 60 40 20 0 - 40 - 20 0 20 40 60 80 85 100 Ambient Temperature º C www.aimtec.com F 051e R11 Tel: +1 514 620 2722 3 of 4 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM15CW-Z 15Watt | DC-DC Converter Test Circuits Notes 1. Input filter (C1, C2, L) are needed to meet conducted emission (EN 55022 Class A) and should be mounted as close as possible to the converter. L 12uH +V input +V output + - C1 2.2uF/100V C2 2.2uF/100V DC/DC Converter - V input Load -V output NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified.5..Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 5. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. www.aimtec.com F 051e R11 Tel: +1 514 620 2722 4 of 4 Toll free: + 1 888 9 AIMTEC (924 6832) North America only