TI AM26LV32INSRG4 Low-voltage high-speed quadruple differential line receiver Datasheet

SLLS202E − MAY 1995 − REVISED JUNE 2005
D
D
D
D
D
D
D
D
D
D OR NS† PACKAGE
(TOP VIEW)
Switching Rates up to 32 MHz
Operates From Single 3.3-V Supply
Ultra-Low Power Dissipation . . . 27 mW Typ
Open-Circuit, Short-Circuit, and Terminated
Fail-Safe
−0.3-V to 5.5-V Common-Mode Range With
± 200-mV Sensitivity
Accepts 5-V Logic Inputs With 3.3-V VCC
Input Hysteresis . . . 50 mV Typ
235 mW With Four Receivers at 32 MHz
Pin-to-Pin Compatible With AM26C32,
AM26LS32, and MB570
1B
1A
1Y
G
2Y
2A
2B
GND
1
16
2
15
3
14
4
13
5
12
6
11
7
10
8
9
VCC
4B
4A
4Y
G
3Y
3A
3B
description/ordering information
The AM26LV32, BiCMOS, quadruple, differential line receiver with 3-state outputs is designed to be similar to
TIA/EIA-422-B and ITU Recommendation V.11 receivers with reduced common-mode voltage range due to
reduced supply voltage.
The device is optimized for balanced bus transmission at switching rates up to 32 MHz. The enable function
is common to all four receivers and offers a choice of active-high or active-low inputs. The 3-state outputs permit
connection directly to a bus-organized system. Each device features receiver high input impedance and input
hysteresis for increased noise immunity, and input sensitivity of ± 200 mV over a common-mode input voltage
range from −0.3 V to 5.5 V. When the inputs are open circuited, the outputs are in the high logic state. This device
is designed using the Texas Instruments (TI) proprietary LinIMPACT-C60 technology, facilitating ultra-low
power consumption without sacrificing speed.
This device offers optimum performance when used with the AM26LV31 quadruple line drivers.
The AM26LV32C is characterized for operation from 0°C to 70°C. The AM26LV32I is characterized for operation
from −45°C to 85°C.
ORDERING INFORMATION
ORDERABLE
PART NUMBER
PACKAGE†
TA
TOP-SIDE
MARKING
AM26LV32CDG4
D
Tape and reel
AM26LV32CDR
AM26LV32C
AM26LV32CDRG4
0°C
0
C to 70
70°C
C
NS
Tube
AM26LV32CNS
Tape and reel
AM26LV32CNSR
26LV32
AM26LV32ID
SOP – D
−40°C to 85°C
SOP – NS
Tube
AM26LV32IDR
Tube
AM26LV32INS
Tape and reel
AM26LV32INSR
AM26LV32I
26LV32I
† Package drawings, standard packing quantities, thermal data, symbolization, and PCB
design guidelines are available at www.ti.com/sc/package.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
LinIMPACT-C60 and TI are trademarks of Texas Instruments.
Copyright  2005, Texas Instruments Incorporated
!" # $%&" !# '%()$!" *!"&+
*%$"# $ " #'&$$!"# '& ",& "&# &-!# #"%&"#
#"!*!* .!!"/+ *%$" '$&##0 *&# " &$&##!)/ $)%*&
"&#"0 !)) '!!&"&#+
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
SLLS202E − MAY 1995 − REVISED JUNE 2005
FUNCTION TABLE
(each receiver)
DIFFERENTIAL
INPUT
ENABLES
OUTPUT
G
G
VID ≥ 0.2 V
H
X
X
L
H
H
−0.2 V < VID < 0.2 V
H
X
X
L
?
?
VID ≤ − 0.2 V
H
X
X
L
L
L
Open, shorted, or
terminated†
H
X
X
L
H
H
X
L
H
Z
H = high level, L = low level, X = irrelevant,
Z = high impedance (off), ? = indeterminate
† See application information attached.
logic symbol‡
logic diagram (positive logic)
G
G
G
1A
1B
2A
2B
3A
3B
4A
4B
4
12
2
≥1
G
EN
3
1
6
7
10
9
14
15
5
11
13
1A
2
1B
1
2A
6
2B
7
3A
10
3B
9
4A
14
4B
15
3 1Y
1Y
2Y
5 2Y
3Y
4Y
‡ This symbol is in accordance with ANSI/IEEE Std 91-1984
and IEC Publication 617-12.
2
4
12
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
11 3Y
13 4Y
SLLS202E − MAY 1995 − REVISED JUNE 2005
schematics of equivalent inputs and outputs
EQUIVALENT OF EACH INPUT (A, B)
TYPICAL OF ALL OUTPUTS (Y)
EQUIVALENT OF EACH
ENABLE INPUT (G, G)
VCC
VCC
VCC
7.2 kΩ
1.5 kΩ
Enable
G, G
A, B
15 kΩ
100 Ω
Y
1.5 kΩ
7.2 kΩ
GND
GND
GND
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage range, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to 6 V
Input voltage range, VI (A or B inputs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −4 V to 8 V
Differential input voltage, VID (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±12 V
Enable input voltage range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to 6 V
Output voltage range, VO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to 6 V
Maximum output current, IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±25 mA
Package thermal impedance, θJA (see Note 3): D package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73°C/W
NS package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64°C/W
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltage values are with respect to the GND terminal.
2. Differential input voltage is measured at the noninverting input with respect to the corresponding inverting input.
3. The package thermal impedance is calculated in accordance with JESD 51.
recommended operating conditions
MIN
NOM
MAX
Supply voltage, VCC
3
3.3
3.6
High-level input voltage, VIH(EN)
2
Low-level input voltage, VIL(EN)
Common-mode input voltage, VIC
−0.3
UNIT
V
V
0.8
V
5.5
V
± 5.8
Differential input voltage, VID
High-level output current, IOH
Low-level output current, IOL
AM26LV32C
Operating free-air temperature, TA
AM26LV32I
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
−5
mA
5
mA
0
70
−40
85
°C
3
SLLS202E − MAY 1995 − REVISED JUNE 2005
electrical characteristics over recommended supply-voltage and operating free-air temperature
ranges (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VIT+
VIT−
Differential input high-threshold voltage
VIK
VOH
Enable input clamp voltage
VOL
IOZ
Low-level output voltage
IIH(E)
IIL(E)
High-level enable input current
rI
Input resistance
II
ICC
Input current
High-impedance-state output current
Low-level enable input current
MAX
−0.2
II = − 18 mA
VID = 200 mV,
VID = − 200 mV,
VO = 0 to VCC
VCC = 0 or 3 V,
VCC = 3.6 V,
IOH = − 5 mA
IOL = 5 mA
2.4
VI = 5.5 V or − 0.3 V,
VI(E) = VCC or GND,
−1.5
3.2
0.17
VI = 5.5 V
VI = 0 V
0.5
V
µA
12
All other inputs GND
8
V
±50
10
Cpd
Power dissipation capacitance‡
One channel
† All typical values are at VCC = 3.3 V and TA = 25°C.
‡ Cpd determines the no-load dynamic current: IS = Cpd × VCC × f + ICC.
V
V
−10
No load, line inputs open
UNIT
V
−0.8
7
Supply current
TYP†
0.2
Differential input low-threshold voltage
High-level output voltage
MIN
µA
A
kΩ
±700
µA
17
mA
150
pF
switching characteristics, VCC = 3.3 V, TA = 25°C
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
8
16
20
8
16
20
UNIT
tPLH
tPHL
Propagation delay time, low- to high-level output
tt
tPZH
Transistion time (tr or tf)
See Figure 1
5
Output-enable time to high level
See Figure 2
17
40
ns
tPZL
tPHZ
Output-enable time to low level
See Figure 3
10
40
ns
Output-disable time from high level
See Figure 2
20
40
ns
tPLZ
tsk(p)§
tsk(o)¶
Output-disable time from low level
See Figure 3
16
40
ns
Pulse skew
4
6
ns
Pulse skew
4
6
Propagation delay time, high- to low-level output
See Figure 1
ns
ns
ns
#
tsk(pp)
Pulse skew (device to device)
6
9
ns
§ tsk(p) is |tPLH − tPHL| of each channel of the same device.
¶ tsk(o) is the maximum difference in propagation delay times between any two channels of the same device switching in the same direction.
# tsk(pp) is the maximum difference in propagation delay times between any two channels of any two devices switching in the same direction.
4
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SLLS202E − MAY 1995 − REVISED JUNE 2005
PARAMETER MEASUREMENT INFORMATION
A
Generator
(see Note B)
Y
VO
B
50 Ω
CL = 15 pF
(see Note A)
50 Ω
A
2V
B
1V
Input
tPLH
Output
VCC
tPHL
90%
50%
10%
G
G
(see Note C)
90%
tr
VOH
50%
10% V
OL
tf
NOTES: A. CL includes probe and jig capacitance.
B. The input pulse is supplied by a generator having the following characteristics: ZO = 50 Ω, PRR = 10 MHz, tr and tf (10% to 90%)
≤ 2 ns, 50% duty cycle.
C. To test the active-low enable G, ground G and apply an inverted waveform G.
Figure 1. tPLH and tPHL Test Circuit and Voltage Waveforms
VID = 1 V
A
Y
VO
B
CL = 15 pF
(see Note A)
RL = 2 kΩ
G
Generator
(see Note B)
50 Ω
G
VCC
(see Note C)
VCC
Input
50%
50%
0V
tPZH
Output
tPHZ
50%
VOH
VOH − 0.3 V
Voff ≈ 0
NOTES: A. CL includes probe and jig capacitance.
B. The input pulse is supplied by a generator having the following characteristics: ZO = 50 Ω, PRR = 10 MHz, tr and tf (10% to 90%)
≤ 2 ns, 50% duty cycle.
C. To test the active-low enable G, ground G and apply an inverted waveform G.
Figure 2. tPZH and tPHZ Test Circuit and Voltage Waveforms
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
SLLS202E − MAY 1995 − REVISED JUNE 2005
PARAMETER MEASUREMENT INFORMATION
VCC
RL = 2 kΩ
A
VID = 1 V
Y
VO
B
CL = 15 pF
(see Note A)
G
Generator
(see Note B)
50 Ω
G
VCC
(see Note C)
VCC
Input
50%
50%
0V
tPZL
tPLZ
Voff ≈ VCC
Output
50%
VOL + 0.3 V
VOL
NOTES: A. CL includes probe and jig capacitance.
B. The input pulse is supplied by a generator having the following characteristics: ZO = 50 Ω, PRR = 10 MHz, tr and tf (10% to 90%)
≤ 2 ns, 50% duty cycle.
C. To test the active-low enable G, ground G and apply an inverted waveform G.
Figure 3. tPZL and tPLZ Test Circuit and Voltage Waveforms
6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SLLS202E − MAY 1995 − REVISED JUNE 2005
APPLICATION INFORMATION
fail-safe conditions
The AM26LV32 quadruple differential line receiver is designed to function properly when appropriately
connected to active drivers. Applications do not always have ideal situations where all bits are being used, the
receiver inputs are never left floating, and fault conditions don’t exist. In actuality, most applications have the
capability to either place the drivers in a high-impedance mode or power down the drivers altogether, and cables
may be purposely (or inadvertently) disconnected, both of which lead to floating receiver inputs. Furthermore,
even though measures are taken to avoid fault conditions like a short between the differential signals, this does
occur. The AM26LV32 has an internal fail-safe circuitry which prevents the device from putting an unknown
voltage signal at the receiver outputs. In the following three cases, a high-state is produced at the respective
output:
1. Open fail-safe − Unused input pins are left open. Do not tie unused pins to ground or any other
voltage. Internal circuitry places the output in the high state.
2. 100-ohm terminated fail-safe − Disconnected cables, drivers in high-impedance state, or
powered-down drivers will not cause the AM26LV32 to malfunction. The outputs will remain in
a high state under these conditions. When the drivers are either turned-off or placed into the
high-impedance state, the receiver input may still be able to pick up noise due to the cable acting
as an antenna. To avoid having a large differential voltage being generated, the use of
twisted-pair cable will induce the noise as a common-mode signal and will be rejected.
3. Shorted fail-safe − Fault conditions that short the differential input pairs together will not cause
incorrect data at the outputs. A differential voltage (VID) of 0 V will force a high state at the
outputs. Shorted fail-safe, however, is not supported across the recommended common-mode
input voltage (VIC) range. An unwanted state can be induced to all outputs when an input is
shorted and is biased with a voltage between −0.3 V and 5.5 V. The shorted fail-safe circuitry
will function properly when an input is shorted, but with no external common-mode voltage
applied.
fail-safe precautions
The internal fail-safe circuitry was designed such that the input common-mode (VIC) and differential
(VID)voltages must be observed. In order to ensure the outputs of unused or inactive receivers remain in a high
state when the inputs are open-circuited, shorted, or terminated, extra precaution must be taken on the active
signal. In applications where the drivers are placed in a high-impedance mode or are powered-down, it is
recommended that for 1, 2, or 3 active receiver inputs, the low-level input voltage (VIL) should be greater than
0.4 V. As in all data transmission applications, it is necessary to provide a return ground path between the two
remote grounds (driver and receiver ground references) to avoid ground differences. Table 1 and Figures 4
through 7 are examples of active input voltages with their respective waveforms and the effect each have on
unused or inactive outputs. Note that the active receivers behave as expected, regardless of the input levels.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
7
SLLS202E − MAY 1995 − REVISED JUNE 2005
APPLICATION INFORMATION
Table 1. Active Receiver Inputs vs Outputs
1, 2, OR 3
ACTIVE INPUTS
SEE
FIGURE
1, 2, OR 3
ACTIVE OUTPUTS
3, 2, OR 1 UNUSED
OR INACTIVE
OUTPUTS
VIL†
900 mV
VID
200 mV
VIC†
1V
4
Known state
High state
−100 mV
200 mV
0V
5
Known state
?
600 mV
800 mV
1V
6
Known state
High state
0
800 mV
400 mV
7
Known state
?
† Measured with respect to ground.
VIC = 1V
VIL = 900 mV
Produces a High State at
Unused or Inactive Outputs
VID = 200 mV
0V
Figure 4. Waveform One
An Unknown State is Produced
at Unused or Inactive Outputs
VIC = 0V
VIL = −100 mV
VID = 200 mV
Figure 5. Waveform Two
VID = 800 mV
VIL = 600 mV
Produces a High State at
Unused or Inactive Outputs
VIC = 1V
0V
Figure 6. Waveform Three
An Unknown State is Produced
at Unused or Inactive Outputs
VID = 800 mV
VIL = 0V
0V
VIC = 400 mV
Figure 7. Waveform Four
8
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SLLS202E − MAY 1995 − REVISED JUNE 2005
APPLICATION INFORMATION
In most applications, it is not customary to have a common-mode input close to ground and to have a differential
voltage larger than 2 V. Since the common-mode input voltage is typically around 1.5 V, a 2-V VID would result
in a VIL of 0.5 V, thus satisfying the recommended VIL level of greater than 0.4 V.
Figure 8 plots seven different input threshold curves from a variety of production lots and shows how the fail-safe
circuitry behaves with the input common-mode voltage levels. These input threshold curves are representative
samples of production devices. The curves specifically illustrate a typical range of input threshold variation. The
AM26LV32 is specified with ±200 mV of input sensitivity to account for the variance in input threshold. Each data
point represents the input’s ability to produce a known state at the output for a given VIC and VID. Applying a
differential voltage at or above a certain point on a curve would produce a known state at the output. Applying
a differential voltage less than a certain point on a curve would activate the fail-safe circuit and the output would
be in a high state. For example, inspecting the top input threshold curve reveals that for a VIC + 1.6 V, VID yields
around 87 mV. Applying 90 mV of differential voltage to this particular production lot generates a known receiver
output voltage. Applying a VID of 80 mV activates the input fail-safe circuitry and the receiver output is placed
in the high state. Texas Instruments specifies the input threshold at ±200 mV, since normal process variations
affect this parameter. Note that at common-mode input voltages around 0.2 V, the input differential voltages are
low compared to their respective data points. This phenomenon points to the fact that the inputs are very
sensitive to small differential voltages around 0.2 V VIC. It is recommended that VIC levels be kept greater than
0.5 V to avoid this increased sensitivity at VIC [ 0.2 V. In most applications, since VIC typically is 1.5 V, the
fail-safe circuitry functions properly to provide a high state at the receiver output.
Most
Applications
100
90
VID − Differential Voltage − mV
80
70
60
50
Not
Recommended
40
30
20
10
Increased Receiver Input Sensitivity
0
−1 −0.8 −0.6 −0.4 −0.2
0
0.2 0.4 0.6 0.8
1
1.2 1.4 1.6 1.8
2
2.2
2.4
VIC − Common-Mode Input Voltage − V
Figure 8. VIC Versus VID Receiver Sensitivity Levels
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
9
SLLS202E − MAY 1995 − REVISED JUNE 2005
APPLICATION INFORMATION
Figure 9 represents a typical application where two receivers are not used. In this case, there is no need to worry
about the output voltages of the unused receivers since they are not connected in the system architecture.
AM26LV32
Connector
RT
System
RT
Unused Circuit
Figure 9. Typical Application with Unused Receivers
Figure 10 shows a common application where one or more drivers are either disabled or powered down. To
ensure the inactive receiver outputs are in a high state, the active receiver inputs must have VIL > 0.4 V and VIC >
0.5 V.
Driver
AM26LV32
Connector
Connector
RT
Enable
RT
Cable
System
RT
Disable or
Power Off
RT
Figure 10. Typical Application Where Two or More Drivers are Disabled
10
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SLLS202E − MAY 1995 − REVISED JUNE 2005
APPLICATION INFORMATION
Figure 11 is an alternative application design to replace the application in Figure 10. This design uses two
AM26LV32 devices, instead of one. However, this design does not require the input levels be monitored to
ensure the outputs are in the correct state, only that they comply to the RS-232 standard.
Driver
AM26LV32
Connector
Connector
RT
Enable
RT
Cable
Unused Circuit
Disable or
Power Off
System
AM26LV32
RT
RT
Unused Circuit
Figure 11. Alternative Solution for Figure 10
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
11
SLLS202E − MAY 1995 − REVISED JUNE 2005
APPLICATION INFORMATION
Figures 12 and 13 show typical applications where a disconnected cable occurs. Figure 12 illustrates a typical
application where a cable is disconnected. Similar to Figure 10, the active input levels must be monitored to
make sure the inactive receiver outputs are in a high state. An alternative solution is shown in Figure 13.
Driver
Connector
AM26LV32
Connector
Cable
RT
RT
System
Unplugged
Cable
RT
RT
Figure 12. Typical Application Where Two or More Drivers are Disconnected
12
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SLLS202E − MAY 1995 − REVISED JUNE 2005
APPLICATION INFORMATION
Figure 13 is an alternative solution so the receiver inputs do not have to be monitored. This solution also requires
the use of two AM26LV32 devices, instead of one.
Driver
AM26LV32
Connector
Connector
Cable
RT
RT
Unused Circuit
System
AM26LV32
Unplugged
Cable
RT
RT
Unused Circuit
Figure 13. Alternative Solution to Figure 12
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
13
SLLS202E − MAY 1995 − REVISED JUNE 2005
APPLICATION INFORMATION
When designing a system using the AM26LV32, the device provides a robust solution where fail-safe and fault
conditions are of concern. The RS-422-like inputs accept common-mode input levels from −0.3 V to 5.5 V with
a specified sensitivity of ±200mV. As previously shown, care must be taken with active input levels since they
can affect the outputs of unused or inactive bits. However, most applications meet or exceed the requirements
to allow the device to perform properly.
14
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
PACKAGE OPTION ADDENDUM
www.ti.com
4-Jun-2007
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
AM26LV32CD
ACTIVE
SOIC
D
16
40
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
AM26LV32CDE4
ACTIVE
SOIC
D
16
40
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
AM26LV32CDG4
ACTIVE
SOIC
D
16
40
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
AM26LV32CDR
ACTIVE
SOIC
D
16
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
AM26LV32CDRE4
ACTIVE
SOIC
D
16
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
AM26LV32CDRG4
ACTIVE
SOIC
D
16
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
AM26LV32CNSLE
OBSOLETE
SO
NS
16
AM26LV32CNSR
ACTIVE
SO
NS
16
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
AM26LV32CNSRE4
ACTIVE
SO
NS
16
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
AM26LV32CNSRG4
ACTIVE
SO
NS
16
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
AM26LV32ID
ACTIVE
SOIC
D
16
40
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
AM26LV32IDE4
ACTIVE
SOIC
D
16
40
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
AM26LV32IDG4
ACTIVE
SOIC
D
16
40
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
AM26LV32IDR
ACTIVE
SOIC
D
16
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
AM26LV32IDRE4
ACTIVE
SOIC
D
16
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
AM26LV32IDRG4
ACTIVE
SOIC
D
16
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
AM26LV32INS
ACTIVE
SO
NS
16
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
AM26LV32INSE4
ACTIVE
SO
NS
16
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
AM26LV32INSG4
ACTIVE
SO
NS
16
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
AM26LV32INSR
ACTIVE
SO
NS
16
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
AM26LV32INSRE4
ACTIVE
SO
NS
16
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
AM26LV32INSRG4
ACTIVE
SO
NS
16
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TBD
(1)
Lead/Ball Finish
Call TI
MSL Peak Temp (3)
Call TI
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
4-Jun-2007
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
4-Oct-2007
TAPE AND REEL BOX INFORMATION
Device
Package Pins
Site
Reel
Diameter
(mm)
Reel
Width
(mm)
A0 (mm)
B0 (mm)
K0 (mm)
P1
(mm)
W
Pin1
(mm) Quadrant
AM26LV32CDR
D
16
SITE 27
330
16
6.5
10.3
2.1
8
16
Q1
AM26LV32CDR
D
16
SITE 41
330
16
6.5
10.3
2.1
8
16
Q1
AM26LV32CNSR
NS
16
SITE 41
330
16
8.2
10.5
2.5
12
16
Q1
AM26LV32IDR
D
16
SITE 27
330
16
6.5
10.3
2.1
8
16
Q1
AM26LV32INSR
NS
16
SITE 41
330
16
8.2
10.5
2.5
12
16
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
4-Oct-2007
Device
Package
Pins
Site
Length (mm)
Width (mm)
Height (mm)
AM26LV32CDR
D
16
SITE 27
342.9
336.6
28.58
AM26LV32CDR
D
16
SITE 41
346.0
346.0
33.0
AM26LV32CNSR
NS
16
SITE 41
346.0
346.0
33.0
AM26LV32IDR
D
16
SITE 27
342.9
336.6
28.58
AM26LV32INSR
NS
16
SITE 41
346.0
346.0
33.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements,
improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.
Customers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s
standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this
warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily
performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should
provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask
work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services
are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such
products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under
the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an
unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties
may be subject to additional restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service
voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business
practice. TI is not responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would
reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement
specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications
of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related
requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any
applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its
representatives against any damages arising out of the use of TI products in such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is
solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in
connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products
are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any
non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
RFID
www.ti-rfid.com
Telephony
www.ti.com/telephony
Low Power
Wireless
www.ti.com/lpw
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2007, Texas Instruments Incorporated