MC1489, MC1489A, SN55189, SN55189A, SN75189, SN75189A QUADRUPLE LINE RECEIVERS SLLS095D – SEPTEMBER 1973 – REVISED OCTOBER 1998 D D description These devices are monolithic low-power Schottky quadruple line receivers designed to satisfy the requirements of the standard interface between data-terminal equipment and data-communication equipment as defined by TIA / EIA-232-F. A separate response-control (CONT) terminal is provided for each receiver. A resistor or a resistor and bias-voltage source can be connected between this terminal and ground to shift the input threshold levels. An external capacitor can be connected between this terminal and ground to provide input noise filtering. The SN55189 and SN55189A are characterized for operation over the full military temperature range of – 55°C to 125°C. The MC1489, MC1489A, SN75189, and SN75189A are characterized for operation from 0°C to 70°C. SN55189, SN55189A . . . J OR W PACKAGE MC1489, MC1489A, SN75189, SN75189A D, N, OR NS† PACKAGE (TOP VIEW) 1A 1CONT 1Y 2A 2CONT 2Y GND 1 14 2 13 3 12 4 11 5 10 6 9 7 8 VCC 4A 4CONT 4Y 3A 3CONT 3Y † The NS package is only available left-end taped and reeled. For SN75189, order SN75189NSR. SN55189, SN55189A . . . FK PACKAGE (TOP VIEW) 1CONT 1A NC VCC 4A D Input Resistance . . . 3 kΩ to 7 kΩ Input Signal Range . . . ± 30 V Operate From Single 5-V Supply Built-In Input Hysteresis (Double Thresholds) Response Control that Provides: Input Threshold Shifting Input Noise Filtering Meet or Exceed the Requirements of TIA / EIA-232-F and ITU Recommendation V.28 Fully Interchangeable With Motorola MC1489 and MC1489A 1Y NC 2A NC 2CONT 4 3 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 4CONT NC 4Y NC 3A 2Y GND NC 3Y 3CONT D D D D NC – No internal connection Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Motorola is a trademark of Motorola, Incorporated. Copyright 1998, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. On products compliant to MIL-PRF-38535, all parameters are tested unless otherwise noted. On all other products, production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 MC1489, MC1489A, SN55189, SN55189A, SN75189, SN75189A QUADRUPLE LINE RECEIVERS SLLS095D – SEPTEMBER 1973 – REVISED OCTOBER 1998 logic symbol† 1A 1 CONT 2A 2 CONT 3A 3 CONT 1 2 4 3 1Y THRS ADJ 6 2Y 5 10 8 3Y 9 13 11 4Y 4A 4 CONT 12 † This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. Pin numbers shown are for the D, J, N, NS, and W packages. logic diagram (positive logic) A Y Response Control schematic (each receiver) VCC 9 kΩ 5 kΩ 1.66 kΩ Output Y R1 Response Control 4 kΩ Input A 10 kΩ GND R1 MC1489 SN55189 SN75189 MC1489A SN55189A SN75189A 8.4 kΩ 1.84 kΩ Resistor values shown are nominal. 2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 MC1489, MC1489A, SN55189, SN55189A, SN75189, SN75189A QUADRUPLE LINE RECEIVERS SLLS095D – SEPTEMBER 1973 – REVISED OCTOBER 1998 absolute maximum ratings over operating free-air temperature (unless otherwise noted)† Supply voltage, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 V Input voltage, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±30 V Output voltage, IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 mA Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table Operating free-air temperature range, TA: SN55189, SN55189A . . . . . . . . . . . . . . . . . . . . . . – 55°C to 125°C MC1489, MC1489A, SN75189, SN75189A . . . . . . 0°C to 70°C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C Case temperature for 60 seconds, FK package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C Lead temperature 1,6 mm (1/16 inch) from case for 60 seconds: J or W package . . . . . . . . . . . . . . . . 300°C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: D, N, or NS package . . . . . . . . . . . . 260°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. All voltage values are with respect to the network ground terminal. DISSIPATION RATING TABLE PACKAGE TA ≤ 25°C POWER RATING DERATING FACTOR ABOVE TA = 25°C TA = 70°C POWER RATING TA = 125°C POWER RATING D 950 mW 7.6 mW/°C 608 mW N/A FK J‡ 1375 mW 11.0 mW/°C 880 mW 275 mW 1375 mW 11.0 mW/°C 880 mW 275 mW N 1150 mW 9.2 mW/°C 736 mW N/A NS 625 mW 4.0 mW/°C 445 mW N/A W 1000 mW 8.0 mW/°C 640 mW ‡ In the J package, SN55189 and SN55189A chips are either silver glass or alloy mounted. 200 mW recommended operating conditions MIN NOM MAX Supply voltage, VCC 4.5 5 5.5 V Input voltage, VI –25 25 V High-level output current, IOH Low-level output current, IOL Operating free-air temperature, TA 0 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 UNIT –0.5 mA 10 mA 70 °C 3 MC1489, MC1489A, SN55189, SN55189A, SN75189, SN75189A QUADRUPLE LINE RECEIVERS SLLS095D – SEPTEMBER 1973 – REVISED OCTOBER 1998 electrical characteristics over operating free-air temperature range, VCC = 5 V ± 1% (unless otherwise noted) TEST FIGURE PARAMETER TEST CONDITIONS† VIT IT+ Positive-going g g input threshold voltage TA = – 55°C to 125°C TA = 25°C 1 ’89A VIT– Negative-going N ti i input i t threshold voltage 1 VOH High-level g output voltage 1 VOL Low-level output voltage IIH ’89, ’89A TA = 0°C to 70°C TA = – 55°C to 125°C TA = 25°C TA = 0°C to 70°C TA = – 55°C to 125°C VI = 0.75 V, IOH = – 0.5 mA UNIT MIN TYP‡ MAX MIN TYP‡ MAX 1 1.3 1.5 1 1.3 1.5 TA = 25°C TA = 0°C to 70°C ’89 MC1489, MC1489A SN75189 SN75189A SN55189 SN55189A 0.9 0.6 1.75 1.6 1.9 1.9 2.25 1.75 1.9 1.55 1.30 0.75 2.25 V 2.25 2.65 1.0 1.25 0.75 1.0 0.65 0.35 1.25 1.25 V 1.6 2.6 4 5 2.6 4 5 2.6 4 5 2.6 4 5 02 0.2 0 45 0.45 02 0.2 0 45 0.45 Input open, IOH = – 0.5 mA 1 VI = 3 V V, IOL = 10 mA High-level g input current 2 VI = 25 V VI = 3 V IIL Low-level input current 2 VI = – 25 V VI = – 3 V IOS Short-circuit output current 3 –3 ICC Supply current 2 VI = 5 V, Outputs open † All characteristics are measured with the response-control terminal open. ‡ All typical values are at VCC = 5 V, TA = 25°C. 20 3.6 8.3 0.43 3.6 8.3 0.43 – 3.6 – 8.3 – 0.43 – 3.6 –8.3 – 0.43 3 –3 26 V V mA mA mA 20 26 TYP MAX RL = 3.9 kΩ 25 85 RL = 390 Ω 25 50 RL = 3.9 kΩ 120 175 RL = 390 Ω 10 20 mA switching characteristics, VCC = 5 V, CL = 15 pF, TA = 25°C TEST FIGURE PARAMETER tPLH tPHL Propagation delay time, low- to high-level output tTLH tTHL Transition time, low- to high-level output 4 Propagation delay time, high- to low-level output Transition time, high- to low-level output POST OFFICE BOX 655303 4 TEST CONDITIONS • DALLAS, TEXAS 75265 MIN UNIT ns ns MC1489, MC1489A, SN55189, SN55189A, SN75189, SN75189A QUADRUPLE LINE RECEIVERS SLLS095D – SEPTEMBER 1973 – REVISED OCTOBER 1998 PARAMETER MEASUREMENT INFORMATION† VCC VIT, V1 – IOH VOH Response Control Open Unless Otherwise Specified VOL RC IOL RC CC – VC +VC Figure 1. VIT + , VIT – , VOH , VOL VCC ICC (see Note A) VI IIH Open IIL Response Control Open NOTE A: ICC is tested for all four receivers simultaneously. Figure 2. IIH , IIL , ICC VCC – IOS Response Control Open Figure 3. IOS † Arrows indicate actual direction of current flow. Current into a terminal is a positive value. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5 MC1489, MC1489A, SN55189, SN55189A, SN75189, SN75189A QUADRUPLE LINE RECEIVERS SLLS095D – SEPTEMBER 1973 – REVISED OCTOBER 1998 PARAMETER MEASUREMENT INFORMATION VCC Output RL Pulse Generator (see Note A) See Note C CL = 15 pF (see Note B) Response Control Open TEST CIRCUIT ≤10 ns ≤10 ns Input 10% 90% 50% 90% 50% 90% 10% 0V tPLH tPHL Output 4V VOH 50% 10% 90% 50% 10% tTHL VOL tTLH VOLTAGE WAVEFORMS NOTES: A. The pulse generator has the following characteristics: ZO = 50 Ω, tw = 500 ns. B. CL includes probe and jig capacitances. C. All diodes are 1N3064 or equivalent. Figure 4. Test Circuit and Voltage Waveforms 6 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 MC1489, MC1489A, SN55189, SN55189A, SN75189, SN75189A QUADRUPLE LINE RECEIVERS SLLS095D – SEPTEMBER 1973 – REVISED OCTOBER 1998 TYPICAL CHARACTERISTICS SN65189, SN75189 OUTPUT VOLTAGE vs INPUT VOLTAGE ÁÁÁ ÁÁÁÁ ÎÎÎÎ ÁÁÁÁ ÁÁÁÁÁ ÁÁÁÁ ÁÁÁÁ ÁÁÁ ÁÁÁÁ ÁÁÁÁ ÁÁÁÁÁ ÁÁÁ ÁÁÁÁ ÁÁÁÁ ÁÁÁÁÁ ÁÁÁÁ ÁÁÁÁ ÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎ 6 V VO O – Output Voltage – V 5 4 3 VIT– 2 RC = ∞ RC = 13 kΩ VC = 5 V RC = 5 kΩ VC = 5 V VIT+ VIT+ VIT– RC = 11 kΩ VC = – 5 V VIT+ VIT– VCC = 5 V TA = 25°C See Figure 1 VIT+ VIT– 1 0 –3 –1 –2 0 1 VI – Input Voltage – V 2 3 4 5 Figure 5 ÁÁÁÁ ÁÁÁÁ 6 VO V O – Output Voltage – V SN65189A, SN75189A OUTPUT VOLTAGE vs INPUT VOLTAGE ÎÎÎÎ ÎÎÎÎ 5 ÁÁÁÁ ÁÁÁÁÁ ÁÁÁÁ ÁÁÁÁÁ ÁÁÁÁÁ RC = ∞ RC = 5 kΩ VC = 5 V VCC = 5 V TA = 25°C See Figure 1 RC = 11 kΩ VC = – 5 V 4 3 VIT– VIT+ VIT– VIT+ VIT– VIT+ 2 1 0 –3 –2 –1 0 1 VI – Input Voltage – V 2 3 4 5 Figure 6 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 7 MC1489, MC1489A, SN55189, SN55189A, SN75189, SN75189A QUADRUPLE LINE RECEIVERS SLLS095D – SEPTEMBER 1973 – REVISED OCTOBER 1998 TYPICAL CHARACTERISTICS† INPUT THRESHOLD VOLTAGE vs SUPPLY VOLTAGE 2.4 2 2.2 1.8 2 ’89A VIT+ 1.8 1.6 ’89 VIT+ 1.4 1.2 ’89 VIT– 1 ’89A VIT– 0.8 ÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ’89A VIT+ 1.6 V IT – Input Threshold Voltage – V V IT – Input Threshold Voltage – V INPUT THRESHOLD VOLTAGE vs FREE-AIR TEMPERATURE ’89 VIT– 1.4 1.2 ’89 VIT+ 1 ’89A VIT– 0.8 0.6 0.4 0.6 0.2 0.4 – 100 – 75 – 50 – 25 0 25 50 0 2 75 100 125 150 3 4 TA – Free-Air Temperature – °C ÎÎÎÎ ÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎ ÁÁÁÁÁ ÎÎÎÎÎ ÁÁÁÁÁ ÎÎÎÎÎ 6 6 VCC = 5 V TA = 25°C See Note A ÎÎÎÎÎ ÎÎÎÎÎ ÁÁÁÁ ÎÎÎÎÎ ÁÁÁÁ ÎÎÎÎÎ ÁÁÁÁ CC = 300 pF 3 ÁÁÁÁ ÁÁÁÁ ÁÁÁÁ ÁÁÁÁ Amplitude – V CC = 500 pF 4 3 CC = 10 pF 1 CC = 100 pF 0 10 40 100 CC = 500 pF ÁÁÁÁ ÁÁÁÁ ÎÎÎÎÎ ÁÁÁÁ ÎÎÎÎÎ ÁÁÁÁ CC = 12 pF 2 2 VCC = 5 V TA = 25°C See Note A 5 CC = 300 pF 4 CC = 100 pF 1 400 1000 4000 10000 0 10 40 100 400 4000 10000 NOTE A: Maximum amplitude of a positive-going pulse that, starting from 0 V, will not cause a change in the output level. Figure 9 Figure 10 † Data for free-air temperatures below 0°C and above 70°C are applicable to SN55189 and SN55189A circuits only. POST OFFICE BOX 655303 1000 tw – Pulse Duration – ns tw – Pulse Duration – ns NOTE A: Maximum amplitude of a positive-going pulse that, starting from 0 V, will not cause a change in the output level. 8 10 SN75189A NOISE REJECTION SN75189 NOISE REJECTION 5 9 Figure 8 Figure 7 Amplitude – V 5 6 7 8 VCC – Supply Voltage – V • DALLAS, TEXAS 75265 MC1489, MC1489A, SN55189, SN55189A, SN75189, SN75189A QUADRUPLE LINE RECEIVERS SLLS095D – SEPTEMBER 1973 – REVISED OCTOBER 1998 TYPICAL CHARACTERISTICS INPUT CURRENT vs INPUT VOLTAGE 10 8 IIII – Input Current – mA 6 4 ÎÎÎÎÎ ÁÁÁÁ ÎÎÎÎÎ ÎÎÎÎÎ VCC = 5 V Control Open TA = 25°C 2 0 –2 –4 –6 –8 –10 – 25 – 20 –15 –10 – 5 0 5 10 VI – Input Voltage – V 15 20 25 Figure 11 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 9 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Low Power Wireless www.ti.com/lpw Telephony www.ti.com/telephony Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2007, Texas Instruments Incorporated PACKAGE OPTION ADDENDUM www.ti.com 9-Oct-2007 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty 5962-86888022A ACTIVE LCCC FK 20 1 TBD 5962-8688802CA ACTIVE CDIP J 14 1 TBD 5962-8688802DA ACTIVE CFP W 14 1 MC1489AN ACTIVE PDIP N 14 25 MC1489ANE4 ACTIVE PDIP N 14 25 MC1489N ACTIVE PDIP N 14 MC1489NE4 ACTIVE PDIP N SN55189AJ ACTIVE CDIP Lead/Ball Finish MSL Peak Temp (3) POST-PLATE N / A for Pkg Type A42 SNPB N / A for Pkg Type TBD A42 SNPB N / A for Pkg Type Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type 14 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type J 14 1 TBD A42 SNPB N / A for Pkg Type SN55189J OBSOLETE CDIP J 14 TBD Call TI SN75189AD ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN75189ADE4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN75189ADG4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN75189ADR ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN75189ADRE4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN75189ADRG4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN75189AN ACTIVE PDIP N 14 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type SN75189ANE4 ACTIVE PDIP N 14 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type SN75189ANSLE OBSOLETE SO NS 14 SN75189ANSR ACTIVE SO NS 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN75189ANSRG4 ACTIVE SO NS 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN75189D ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN75189DE4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN75189DG4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN75189DR ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN75189DRE4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN75189DRG4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN75189N ACTIVE PDIP N 14 CU NIPDAU N / A for Pkg Type TBD 25 Addendum-Page 1 Pb-Free (RoHS) Call TI Call TI Call TI PACKAGE OPTION ADDENDUM www.ti.com 9-Oct-2007 Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty SN75189NE4 ACTIVE PDIP N 14 SN75189NSR ACTIVE SO NS 14 SN75189NSRE4 ACTIVE SO NS SN75189NSRG4 ACTIVE SO SNJ55189AFK ACTIVE LCCC 25 Pb-Free (RoHS) Lead/Ball Finish MSL Peak Temp (3) CU NIPDAU N / A for Pkg Type 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM NS 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM FK 20 1 TBD POST-PLATE N / A for Pkg Type SNJ55189AJ ACTIVE CDIP J 14 1 TBD A42 SNPB N / A for Pkg Type SNJ55189AW ACTIVE CFP W 14 1 TBD A42 SNPB N / A for Pkg Type SNJ55189FK OBSOLETE LCCC FK 20 TBD Call TI Call TI SNJ55189J OBSOLETE CDIP J 14 TBD Call TI Call TI (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 11-Mar-2008 TAPE AND REEL INFORMATION *All dimensions are nominal Device SN75189ADR Package Package Pins Type Drawing SPQ Reel Reel Diameter Width (mm) W1 (mm) A0 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 SN75189ANSR SO NS 14 2000 330.0 16.4 8.2 10.5 2.5 12.0 16.0 Q1 SN75189DR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 SN75189NSR SO NS 14 2000 330.0 16.4 8.2 10.5 2.5 12.0 16.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 11-Mar-2008 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) SN75189ADR SOIC D 14 2500 346.0 346.0 33.0 SN75189ANSR SO NS 14 2000 346.0 346.0 33.0 SN75189DR SOIC D 14 2500 346.0 346.0 33.0 SN75189NSR SO NS 14 2000 346.0 346.0 33.0 Pack Materials-Page 2 MECHANICAL DATA MLCC006B – OCTOBER 1996 FK (S-CQCC-N**) LEADLESS CERAMIC CHIP CARRIER 28 TERMINAL SHOWN 18 17 16 15 14 13 NO. OF TERMINALS ** 12 19 11 20 10 A B MIN MAX MIN MAX 20 0.342 (8,69) 0.358 (9,09) 0.307 (7,80) 0.358 (9,09) 28 0.442 (11,23) 0.458 (11,63) 0.406 (10,31) 0.458 (11,63) 21 9 22 8 44 0.640 (16,26) 0.660 (16,76) 0.495 (12,58) 0.560 (14,22) 23 7 52 0.739 (18,78) 0.761 (19,32) 0.495 (12,58) 0.560 (14,22) 24 6 68 0.938 (23,83) 0.962 (24,43) 0.850 (21,6) 0.858 (21,8) 84 1.141 (28,99) 1.165 (29,59) 1.047 (26,6) 1.063 (27,0) B SQ A SQ 25 5 26 27 28 1 2 3 4 0.080 (2,03) 0.064 (1,63) 0.020 (0,51) 0.010 (0,25) 0.020 (0,51) 0.010 (0,25) 0.055 (1,40) 0.045 (1,14) 0.045 (1,14) 0.035 (0,89) 0.045 (1,14) 0.035 (0,89) 0.028 (0,71) 0.022 (0,54) 0.050 (1,27) 4040140 / D 10/96 NOTES: A. B. C. D. E. All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. This package can be hermetically sealed with a metal lid. The terminals are gold plated. Falls within JEDEC MS-004 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Data Converters DSP Clocks and Timers Interface Logic Power Mgmt Microcontrollers RFID RF/IF and ZigBee® Solutions amplifier.ti.com dataconverter.ti.com dsp.ti.com www.ti.com/clocks interface.ti.com logic.ti.com power.ti.com microcontroller.ti.com www.ti-rfid.com www.ti.com/lprf Applications Audio Automotive Broadband Digital Control Medical Military Optical Networking Security Telephony Video & Imaging Wireless www.ti.com/audio www.ti.com/automotive www.ti.com/broadband www.ti.com/digitalcontrol www.ti.com/medical www.ti.com/military www.ti.com/opticalnetwork www.ti.com/security www.ti.com/telephony www.ti.com/video www.ti.com/wireless Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2008, Texas Instruments Incorporated