MEDICAL & MILITARY Medline 200 Series 1 5 0 - 2 0 0 W AT T S S I N G L E & M U LT I P L E O U T P U T A C / D C M E D I C A L Features • Low safety ground leakage current • Wide input range 90 to 260Vac • Input surge current protection • Overvoltage protection • Overcurrent protection • Power fail detection (PFD) signal • Optional cover and fan assembly • 100% burn-in at full rated load • Remote inhibit - TTL high disables output • Short curcuit protection Specifications PFD signal TTL logic high for normal operation and TTL logic low upon loss of input power. This signal appears at least 1ms prior to +5V output dropping 5% below its nominal value. This signal also provides a minimum delay of 100ms after +5V is within regulation Efficiency 70% min on all models Hold up time 20ms min at 110VAC Line regulation ± 0.5% max at full load INPUT Voltage range 90-260VAC Frequency 47-63Hz. Input Current 3.2A (rms) at 115VAC 1.6A (rms) at 230VAC Leakage current 90µA max at 115VAC, 60Hz 150A max at 230VAC, 50Hz Inrush Current 20A @ 115V or 40A at 230V at 25°C and cold start ENVIRONMENTAL Isolation Input – Output: 4000VAC Input – Ground: 1500VAC Output – Ground: 500VAC Operating Temperature 0°C to 70°C Storage temperature –40°C to +85°C Humidity 5% to 95% non-condensing Derating Derate from 100% at +50°C linearly to 50% at +70°C. Cooling 25CFM forced air, provided on “C” version, to be provided for “B” version by user OUTPUT Power 200W Voltage See table Current See table Ripple & Noise 2% p-p max GENERAL Overvoltage protection Provided on output #1 only, set at 112-132% of it nominal output voltage Switching frequency 88-112kHz. MTBF 350,000 hours at full load 25°C ambient , calculated per MIL-HDBK-217F Overcurrent Protection The output protected to short circuit conditions Temperature coefficient 0.04%°C all outputs STANDARDS AND APPROVALS Transient response Max excursion of 4% or better on all models, recovering to 1% of final value within 500us after a 25% step load change Safety standards IEC60601-1 TUV EN60601-1, EN60601-1 C-Tick AS/NZS CISPR11 Group 1, Class A EMC standards EN55011 Class B, FCC Class B,VCII, EN61000-3-2, -3, EN60001-4-2, -3, -4, -5, -6, -8, -11 Technical Illustration MECHANICAL Dimensions See drawing Weight 0.82kg for “B” version 0.96kg for version “C” version Notes: 1. Dimensions shown in inches (mm) 2. Tolerance 0.02 (0.5) maximum 3. Input connector P1 is Dinkle DT-35-B01W-09 screws are M3, nickle plated 4. Connector P3 mates with Molex housing 22-01-1043 and Molex 40445 series crimp terminal 5. Connector P4/P5 mates with Molex housing 22-01-1023 and Molex 40445 series crimp terminal 6. P4 is for DC fan rated 24V/0.2A (models PM201/27), or 5V/0.38A (models PM201-40-3), and 12V/0.2A (other models, Pin1 +V and Pin2 COM 7. Weight: 0.82 Kgs (1.83 Lbs) approx for “B” version 0.96 Kgs (2.14 Lbs) approx for “C” version Your dependable power partner – www.powerbox.com.au 345 MEDICAL & MILITARY Medline 200 Series 1 5 0 - 2 0 0 W AT T S S I N G L E & M U LT I P L E O U T P U T A C / D C M E D I C A L Selection Table MAX. OUTPUT #1 MODEL OUTPUT #2 VNOM IMIN IMAX OUTPUT #3 TOL VNOM OUTPUT #4 IMIN IMAX TOL VNOM IMIN OUTPUT NUMBER VNOM IMIN IMAX TOL IMAX TOL POWER OBN01016 5.1V 0A 35A 2% 175W OBN01013 3.3V 0A 46A 3% 150W OBN01037 12V 0A 16.7A 2% 200W OBN01046 15V 0A 13.4A 2% 200W OBN01055 24V 0A 8.4A 2% 200W OBN01070 30V 0A 6.7A 2% 200W OBN01204 48V 0A 4.2A 2% 200W OBN01207 +5.1V 3.0A 30A 2% +12V 0A 8A 4% 200W OBN01210 +5.1V 3.0A 30A 2% +15V 0A 6A 4% 200W OBN012A5 +5.1V 3.0A 30A 2% +24V 0A 4A 4% 200W OBN01310 +12V 1.0A 8A 2% +24V 0A 4A 4% OBN01313 +5.1V 3.0A 30A 2% +12V 0A 8A 4% -5V 0A 6A 4% 200W OBN01316 +5.1V 3.0A 30A 2% +12V 0A 8A 4% -12V 0A 4A 4% 200W OBN01315 +5.1V 3.0A 30A 2% +15V 0A 6A 4% -15V 0A 4A 4% 200W OBN01319 +5.1V 3.0A 30A 2% +15V 0A 6A 4% -12V 0A 4A 4% 200W OBN01404 +5.1V 3.0A 30A 2% +12V 0A 8A 4% -24V 0A 4A 4% 200W OBN01403 +5.1V 3.0A 30A 2% +12V 0A 8A 4% -12V 0A 4A 4% 5V 0A 6A 4% 200W OBN01407 +5.1V 3.0A 30A 2% +15V 0A 6A 4% -15V 0A 4A 4% 24V 0A 4A 4% 200W OBN01410 +5.1V 3.0A 30A 2% +12V 0A 8A 4% -12V 0A 4A 4% 12V 0A 4A 4% 200W OBN01420 +5.1V 3.0A 30A 2% +12V 0A 8A 4% -15V 0A 4A 4% 15V 0A 4A 4% 200W OBN01413 +3.3V 3.0A 30A 3% +5.1V 0A 8A 4% -12V 0A 4A 4% 12V 0A 4A 4% 175W 200W NOTES: (1) Add suffix “B” for U-bracket format and “C” for enclosed format. (2) Peak current is 12A on +12V, 9A on +15V and 6A on +24V. (3) Output #4 is floating. It can be connected externally for positive or negative output. (4) 200 watts for “C” version with a cover and fan assembly 100 watts for “B” version without moving air (maximum current of ouput #1 & #2 derated to 50%), or 200 watts with 25 CFM forced air provided by user. (5) When the remote Sense facility is not used, +Sense must be connected to +V, and -Sense to Return, on P2 connector. (6) All models may be operated at no-load. At no-load, output voltage tolerance increases to 10%. Pin Chart CONNECTOR P1 MODEL/PIN OBN01016 OBN01031 OBN01046 OBN01070 OBN01013 OBN0PM201-13 OBN01055 OBN01204 OBN01210 OBN01207 OBN01310 OBN01316 OBN01313 OBN01315 OBN01319 OBN01404 OBN01407 OBN01420 346 OBN01403 OBN01410 OBN14113 P2 P3 P4 1 2 3 4 5 -Sense RET. RET. RET RET Output Output Output +Sense FAN #1 #1 #1 RET Output #1 Output COM #1 RET. COM RET. COM RET. Output #2 Output #1 Output COM #1 RET. COM RET. COM RET. Output Output #2 #3 Output #1 Output COM #1 RET. COM RET. COM RET. Output #2 COM RET. COM RET. COM RET. Output #1 Output #1 6 7 8 9 1 2 3 4 1 2 COM COM. PFD INHIBIT+ INHIBITRET. FAN COM COM RET. RET. PFD INHIBIT+ INHIBIT- FAN COM COM RET. RET. PFD INHIBIT+ INHIBIT- Output Output #3 #3 RETURN FAN COM COM RET. RET. PFD INHIBIT+ INHIBIT- Output Output Output Output #2 #2 #3 #4 RETURN FAN COM COM RET. RET. PFD INHIBIT+ INHIBIT- N.C. N.C. N.C. N.C. N.C. N.C.