ADS7817 AD ADS 781 7 OPSA7817 658 SBAS066A – MAY 2001 12-Bit Differential Input Micro Power Sampling ANALOG-TO-DIGITAL CONVERTER FEATURES DESCRIPTION ● ● ● ● ● ● ● ● The ADS7817 is a 12-bit, 200kHz sampling Analog-toDigital (A/D) converter that features a high impedance fully differential analog input. The reference voltage can be varied from 100mV to 2.5V, with a corresponding inputreferred resolution between 49µV and 1.22mV. The differential input, low power, automatic power down, and small size make the ADS7817 ideal for direct connection to transducers in battery operated systems, remote data acquisition, or multi-channel applications. The ADS7817 is available in a plastic mini-DIP-8, an SO-8, or an MSOP-8 package. BIPOLAR INPUT RANGE TRUE DIFFERENTIAL INPUT 200kHz SAMPLING RATE MICRO POWER: 2.3mW at 200kHz POWER DOWN: 3µA Max AVAILABLE IN MSOP-8 PACKAGE SERIAL INTERFACE AC COMMON-MODE REJECTION APPLICATIONS ● ● ● ● ● TRANSDUCER INTERFACE BATTERY OPERATED SYSTEMS REMOTE DATA ACQUISITION ISOLATED DATA ACQUISITION AC MOTOR CONTROL Control SAR VREF DOUT +In CDAC Serial Interface –In S/H Amp Comparator DCLOCK CS/SHDN Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright © 1997, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. www.ti.com ABSOLUTE MAXIMUM RATINGS(1) ELECTROSTATIC DISCHARGE SENSITIVITY +VCC ..................................................................................................... +6V Analog Input ........................................................... –0.3V to (+VCC + 0.3V) Logic Input ............................................................. –0.3V to (+VCC + 0.3V) Case Temperature ......................................................................... +100°C Junction Temperature .................................................................... +150°C Storage Temperature ..................................................................... +125°C External Reference Voltage .............................................................. +5.5V This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. NOTE: (1) Stresses above these ratings may permanently damage the device. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. PIN CONFIGURATION VREF 1 +In 2 8 +VCC 7 DCLOCK ADS7817 –In 3 6 DOUT GND 4 5 CS/SHDN PDIP-8, SOIC-8, MSOP-8 PIN DESCRIPTIONS PIN NAME 1 VREF DESCRIPTION 2 +In Non Inverting Input. 3 –In Inverting Input. Reference Input. 4 GND 5 CS/SHDN Ground. 6 DOUT 7 DCLOCK 8 +VCC Chip Select when LOW, Shutdown Mode when HIGH. The serial output data word is comprised of 12 bits of data. In operation the data is valid on the falling edge of DCLOCK. The second clock pulse after the falling edge of CS enables the serial output. After one null bit the data is valid for the next 12 edges. Data Clock synchronizes the serial data transfer and determines conversion speed. Power Supply. PACKAGE/ORDERING INFORMATION PRODUCT ADS7817P ADS7817U ADS7817U ADS7817E ADS7817E ADS7817E ADS7817PB ADS7817UB ADS7817UB ADS7817EB ADS7817EB ADS7817EB ADS7817PC ADS7817UC ADS7817UC ADS7817EC ADS7817EC ADS7817EC MAXIMUM INTEGRAL LINEARITY ERROR (LSB) MAXIMUM DIFFERENTIAL LINEARITY ERROR (LSB) ±2 ±2 PACKAGE PACKAGE DRAWING NUMBER(1) SPECIFICATION TEMPERATURE RANGE PACKAGE MARKING(2) ±2 ±2 DIP-8 SO-8 006 182 –40°C to +85°C –40°C to +85°C ADS7817P ADS7817U " " " " " ±2 ±2 MSOP-8 337 –40°C to +85°C " " " " " " " " " " ±2 ±2 ±1 ±1 Plastic DIP-8 SO-8 006 182 –40°C to +85°C –40°C to +85°C " " " " " ±2 ±1 MSOP 337 –40°C to +85°C " " " " " " " " " " ±1 ±1 ±0.75 ±0.75 DIP-8 SO-8 006 182 –40°C to +85°C –40°C to +85°C " " " " " ±1 ±0.75 MSOP-8 337 –40°C to +85°C " " " " " " " " " " ORDERING NUMBER(3) ADS7817P ADS7817U " ADS7817U/2K5 A17 ADS7817E " ADS7817E/250 " ADS7817E/2K5 ADS7817PB ADS7817PB ADS7817UB ADS7817UB " ADS7817UB/2K5 A17 ADS7817EB " ADS7817EB/250 " ADS7817EB/2K5 ADS7817PC ADS7817PC ADS7817UC ADS7817UC " ADS7817UC/2K5 A17 ADS7817EC " ADS7817EC/250 " ADS7817EC/2K5 TRANSPORT MEDIA Rails " Tape and Reel Rails Tape and Reel " Rails " Tape and Reel Rails Tape and Reel " Rails " Tape and Reel Rails Tape and Reel " NOTE: (1) For detail drawing and dimension table, please see end of data sheet or Package Drawing File on Web. (2) Performance Grade information is marked on the reel. (3) Models with a slash(/) are available only in Tape and reel in quantities indicated (e.g. /250 indicates 250 units per reel, /2K5 indicates 2500 devices per reel). Ordering 2500 pieces of ”ADS7817E/2K5“ will get a single 2500-piece Tape and Reel. 2 ADS7817 SBAS066A ELECTRICAL CHARACTERISTICS At –40°C to +85°C, +VCC = +5V, VREF = +2.5V, fSAMPLE = 200kHz, fCLK = 16 • fSAMPLE, –In = +2.5V, unless otherwise specified. ADS7817 PARAMETER CONDITIONS MIN +In – (–In) +In –In –VREF –0.3 –0.3 ANALOG INPUT Full-Scale Input Span Absolute Input Voltage Capacitance Leakage Current REFERENCE INPUT Voltage Range Resistance Current Drain DIGITAL INPUT/OUTPUT Logic Family Logic Levels: VIH VIL VOH VOL Data Format +VREF VCC +0.3 4 ✻ ✻ ✻ TYP ±2 ±2 ±6 ±4 ±0.8 ±0.7 ✻ ✻ ✻ ✻ ✻ 0.1 3 –0.3 3.5 ✻ ✻ ✻ –40 ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ +85 ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ Clk Cycles Clk Cycles kHz V GΩ GΩ µA µA µA ✻ ✻ ✻ ✻ Bits Bits LSB(1) LSB LSB LSB µVrms dB dB dB dB dB dB ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ 3 ±1 ±1 ✻ ✻ ✻ ✻ 5.25 800 V V V pF µA ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ ✻ 0.4 Binary Two’s Complement 460 40 330 ✻ ✻ ✻ ✻ ✻ 100 20 3 +VCC +0.3 0.8 4.75 ±0.5 ±0.4 ✻ ✻ ✻ ✻ ✻ ✻ CMOS IIH = +5µA IIL = +5µA IOH = –250µA IOL = 250µA ±2 ±1 ✻ ✻ ✻ ✻ ✻ ✻ 2.5 5 5 20 1.3 0.001 CS = VCC CS = GND, fSAMPLE = 0Hz At Code FF8h fSAMPLE = 12.5kHz CS = VCC UNITS ✻ ✻ –83 –81 71 86 MAX ✻ ✻ ✻ 200 1kHz 5kHz 1kHz 1kHz ✻ ✻ ✻ TYP ✻ 12 at at at at ✻ ✻ ✻ ✻ 1.5 5.0Vp-p 5.0Vp-p 5.0Vp-p 5.0Vp-p MIN 12 ±1 ±1 ±1 ±0.5 63 80 82 VIN = VIN = VIN = VIN = ADS7817C MAX ✻ ✻ 12 POWER SUPPLY REQUIREMENTS VCC Specified Performance Quiescent Current fSAMPLE = 12.5kHz(2, 3) fSAMPLE = 12.5kHz(3) Power Down CS =VCC, fSAMPLE = 0Hz TEMPERATURE RANGE Specified Performance MIN 11 SAMPLING DYNAMICS Conversion Time Acquisition Time Throughput Rate SINAD Spurious Free Dynamic Range ADS7817B MAX 15 ±1 SYSTEM PERFORMANCE Resolution No Missing Codes Integral Linearity Error Differential Linearity Error Offset Error Gain Error Noise Common-Mode Rejection Power Supply Rejection DYNAMIC CHARACTERISTICS Total Harmonic Distortion TYP ✻ ✻ ✻ ✻ V V V V ✻ V µA µA µA µA ✻ °C ✻ Specifications same as ADS7817. NOTE: (1) LSB means Least Significant Bit, with VREF equal to +2.5V, one LSB is 1.22mV. (2) fCLK = 3.2MHz, CS = VCC for 241 clock cycles out of every 256. (3) See the Power Dissipation section for more information regarding lower sample rates. ADS7817 SBAS066A 3 TIMING CHARACTERISTICS At TA = +25°C, VCC = +5V, VREF = +2.5V, fSAMPLE = 200kHz, and fCLK = 16 • fSAMPLE, –In = +2.5V, unless otherwise specified. CHANGE IN OFFSET vs TEMPERATURE CHANGE IN OFFSET vs REFERENCE VOLTAGE 1.2 5 0.8 4 Delta from 25°C (LSB) Change in Offset (LSB) 4.5 3.5 3 2.5 2 1.5 1 0.4 0.0 –0.4 –0.8 0.5 –1.2 0 1.0 1.25 1.5 1.75 2.0 Reference Voltage (V) 2.25 –50 2.5 75 100 0.1 Delta from 25°C (LSB) Change in Gain (LSB) 25 50 Temperature (°C) 0.15 3.5 3 2.5 2 1.5 1 0.05 0 –0.05 –0.1 0.5 0 1.0 1.25 1.5 1.75 2.0 Reference Voltage (V) 2.25 2.5 –0.15 –50 11.5 15 Peak-to-Peak Noise (LSB) 18 11.0 10.5 10.0 9.5 9.0 1 Reference Voltage 0 25 50 75 100 PEAK-TO-PEAK NOISE vs REFERENCE VOLTAGE 12.0 0.1 –25 Temperature (°C) EFFECTIVE NUMBER OF BITS vs REFERENCE VOLTAGE Effective Number of Bits 0 CHANGE IN GAIN vs TEMPERATURE CHANGE IN GAIN vs REFERENCE VOLTAGE 4 4 –25 10 12 9 6 3 0 0.1 1 10 Reference Voltage ADS7817 SBAS066A TIMING CHARACTERISTICS (Cont.) At TA = +25°C, VCC = +5V, VREF = +2.5V, fSAMPLE = 200kHz, and fCLK = 16 • fSAMPLE, –In = +2.5V, unless otherwise specified. FREQUENCY SPECTRUM (4096 Point FFT; fIN = 9.9kHz, –0.5dB) POWER SUPPLY REJECTION vs RIPPLE FREQUENCY 0 0 –20 –20 –30 Amplitude (dB) Power Supply Rejection (dB) –10 –40 –50 –60 –40 –60 –80 –70 –100 –80 –90 –120 10 100 1000 Ripple Frequency (kHz) 10000 0 25 100 95 73 72 –95 90 SNR –90 SFDR 71 SFDR (dB) SNR and SINAD (dB) 75 SPURIOUS FREE DYNAMIC RANGE AND TOTAL HARMONIC DISTORTION vs INPUT FREQUENCY SIGNAL-TO-NOISE RATIO AND SIGNAL-TO-(NOISE+DISTORTION) vs INPUT FREQUENCY 70 SINAD 85 –85 80 –80 75 69 –75 THD 70 68 –70 65 67 1 10 –65 1 100 10 100 Input Frequency (kHz) Input Frequency (kHz) SIGNAL-TO-(NOISE+DISTORTION) vs INPUT LEVEL CHANGE IN INTEGRAL LINEARITY and DIFFERENTIAL LINEARITY vs SAMPLE RATE 1.5 Delta from fSAMPLE = 200kHz (LSB) 80 70 60 SINAD (dB) 50 Frequency (kHz) THD (dB) 1 50 40 30 20 1.0 Change in Integral Linearity (LSB) 0.5 0 Change in Differential Linearity (LSB) –0.5 10 –60 –50 –40 –30 Input Level (dB) ADS7817 SBAS066A –20 –10 0 0 80 160 240 320 400 Sample Rate (kHz) 5 TIMING CHARACTERISTICS (Cont.) At TA = +25°C, VCC = +5V, VREF = +2.5V, fSAMPLE = 200kHz, and fCLK = 16 • fSAMPLE, –In = +2.5V, unless otherwise specified. DIFFERENTIAL LINEARITY ERROR vs CODE 1.00 0.75 0.75 0.50 0.50 0.25 0.25 DLE (LSB) ILE (LSB) INTEGRAL LINEARITY ERROR vs CODE 1.00 0.00 –0.25 0.00 –0.25 –0.50 –0.50 –0.75 –0.75 –1.00 –1.00 800 000 800 7FF 000 CHANGE IN INTEGRAL LINEARITY AND DIFFERENTIAL LINEARITY vs REFERENCE VOLTAGE INPUT LEAKAGE CURRENT vs TEMPERATURE 10 0.05 Leakage Current (nA) Delta from +2.5V Reference (LSB) 0.10 Change in Differential Linearity (LSB) 0.00 –0.05 –0.10 Change in Integral Linearity (LSB) –0.15 –0.20 1 0.1 0.01 1 1.25 1.5 1.75 2.0 Reference Voltage (V) 2.25 –50 2.5 0 25 50 75 100 75 100 POWER DOWN SUPPLY CURRENT vs TEMPERATURE 600 3 550 2.5 Supply Current (µA) Supply Current (µA) –25 Temperature (°C) SUPPLY CURRENT vs TEMPERATURE 500 450 400 350 2 1.5 1 0.5 300 0 –50 –25 0 25 50 Temperature (°C) 6 7FF Hex BTC Code Hex BTC Code 75 100 –50 –25 0 25 50 Temperature (°C) ADS7817 SBAS066A TIMING CHARACTERISTICS (Cont.) At TA = +25°C, VCC = +5V, VREF = +2.5V, fSAMPLE = 200kHz, and fCLK = 16 • fSAMPLE, –In = +2.5V, unless otherwise specified. REFERENCE CURRENT vs TEMPERATURE (Code = FF8h) REFERENCE CURRENT vs SAMPLE RATE (Code = FF8h) 20 30 Reference Current (µA) Reference Current (µA) 25 15 10 5 20 15 10 5 0 0 0 40 80 120 Sample Rate (kHz) ADS7817 SBAS066A 160 200 –50 –25 0 25 50 75 100 Temperature (°C) 7 THEORY OF OPERATION 2 • VREF peak-to-peak The ADS7817 is a classic successive approximation register (SAR) analog-to-digital (A/D) converter. The architecture is based on capacitive redistribution which inherently includes a sample/hold function. The converter is fabricated on a 0.6µ CMOS process. The architecture and process allow the ADS7817 to acquire and convert an analog signal at up to 200,000 conversions per second while consuming very little power. The external clock can vary between 10kHz (625Hz throughput) and 3.2MHz (200kHz throughput). The duty cycle of the clock is essentially unimportant as long as the minimum high and low times are at least 150ns. The minimum clock frequency is set by the leakage on the capacitors internal to the ADS7817. The analog input is provided to two input pins: +In and –In. When a conversion is initiated, the differential input on these pins is sampled on the internal capacitor array. While a conversion is in progress, both inputs are disconnected from any internal function. The digital result of the conversion is clocked out by the DCLOCK input and is provided serially, most significant bit first, on the DOUT pin. The digital data that is provided on the DOUT pin is for the conversion currently in progress—there is no pipeline delay. It is possible to continue to clock the ADS7817 after the conversion is complete and to obtain the serial data least significant bit first. See the Digital Interface section for more information. Common Voltage Single-Ended Input VREF peak-to-peak ADS7817 Common Voltage VREF peak-to-peak Differential Input FIGURE 1. Methods of Driving the ADS7817: SingleEnded or Differential. 5 VCC = 5V 4.0 4 Common Voltage Range (V) The ADS7817 requires an external reference, an external clock, and a single +5V power source. The external reference can be any voltage between 100mV and 2.5V. The value of the reference voltage directly sets the range of the analog input. The reference input current depends on the conversion rate of the ADS7817. ADS7817 Single-Ended Input 3 2.8 2.2 2 1 0 –0.3 –1 0.0 0.5 1.0 1.5 2.0 2.5 VREF (V) FIGURE 2. Single-Ended Input: Common Voltage Range vs VREF. ANALOG INPUT When the input is differential, the amplitude of the input is the difference between the +In and –In input, or: +In – (–In). A voltage or signal is common to both of these inputs. The peakto-peak amplitude of each input is VREF about this common voltage. However, since the inputs are 180° out of phase, the peak-to-peak amplitude of the difference voltage is 2 • VREF. The value of VREF also determines the range of the voltage that may be common to both inputs (see Figure 3). 5 VCC = 5V 4.0 4 Common Voltage Range (V) The analog input is bipolar and fully differential. There are two general methods of driving the analog input of the ADS7817: single-ended or differential (see Figure 1). When the input is single-ended, the –In input is held at a fixed voltage. The +In input swings around the same voltage and the peak-to-peak amplitude is 2 • VREF. The value of VREF determines the range over which the common voltage may vary (see Figure 2). 3 Differential Input 2.75 2 1 1.95 0 –0.3 –1 0.0 0.5 1.0 1.5 2.0 2.5 VREF (V) FIGURE 3. Differential Input: Common Voltage Range vs VREF. 8 ADS7817 SBAS066A In each case, care should be taken to ensure that the output impedance of the sources driving the +In and –In inputs are matched. If this is not observed, the two inputs could have different settling times. This may result in offset error, gain error, and linearity error which change with both temperature and input voltage. If the impedance cannot be matched, the errors can be lessened by giving the ADS7817 more acquisition time. The input current on the analog inputs depends on a number of factors: sample rate, input voltage, and source impedance. Essentially, the current into the ADS7817 charges the internal capacitor array during the sample period. After this capacitance has been fully charged, there is no further input current. The source of the analog input voltage must be able to charge the input capacitance (15pF) to a 12-bit settling level within 1.5 clock cycles. When the converter goes into the hold mode or while it is in the power down mode, the input impedance is greater than 1GΩ. Care must be taken regarding the absolute analog input voltage. The +In input should always remain within the range of GND –300mV to VCC +300mV. The –In input should always remain within the range of GND –300mV to 4V. Outside of these ranges, the converter’s linearity may not meet specifications. With lower reference voltages, extra care should be taken to provide a clean layout including adequate bypassing, a clean power supply, a low-noise reference, and a low-noise input signal. Because the LSB size is lower, the converter will also be more sensitive to external sources of error such as nearby digital signals and electromagnetic interference. The current that must be provided by the external reference will depend on the conversion result. The current is lowest at negative full-scale (800h) and is typically 15µA at a 200kHz conversion rate (25°C). For the same conditions, the current will increase as the analog input approaches positive full scale, reaching 25µA at an output result of 7FFh. The current does not increase linearly, but depends, to some degree, on the bit pattern of the digital output. The reference current diminishes directly with both conversion rate and reference voltage. As the current from the reference is drawn on each bit decision, clocking the converter more quickly during a given conversion period will not reduce the overall current drain from the reference. The reference current changes only slightly with temperature. See the curves, “Reference Current vs Sample Rate” and “Reference Current vs Temperature” in the Typical Performance Curves section for more information. DIGITAL INTERFACE REFERENCE INPUT The external reference sets the analog input range. The ADS7817 will operate with a reference in the range of 100mV to 2.5V. There are several important implications of this. As the reference voltage is reduced, the analog voltage weight of each digital output code is reduced. This is often referred to as the LSB (least significant bit) size and is equal to two times the reference voltage divided by 4096. This means that any offset or gain error inherent in the A/D converter will appear to increase, in terms of LSB size, as the reference voltage is reduced. The typical performance curves of “Change in Offset vs Reference Voltage” and “Change in Gain vs Reference Voltage” provide more information. The noise inherent in the converter will also appear to increase with lower LSB size. With a 2.5V reference, the internal noise of the converter typically contributes only 0.52 LSB peak-to-peak of potential error to the output code. When the external reference is 100mV, the potential error contribution from the internal noise will be 25 times larger— 13 LSBs. The errors due to the internal noise are gaussian in nature and can be reduced by averaging consecutive conversion results. For more information regarding noise, consult the typical performance curves “Effective Number of Bits vs Reference Voltage” and “Peak-to-Peak Noise vs Reference Voltage.” Note that the effective number of bits (ENOB) figure is calculated based on the converter’s signal-to-(noise + distortion) with a 1kHz, 0dB input signal. SINAD is related to ENOB as follows: SINAD = 6.02 • ENOB + 1.76. ADS7817 SBAS066A SERIAL INTERFACE The ADS7817 communicates with microprocessors and other digital systems via a synchronous 3-wire serial interface as shown in Figure 4 and Table I. The DCLOCK signal synchronizes the data transfer with each bit being transmitted on the falling edge of DCLOCK. Most receiving systems will capture the bitstream on the rising edge of DCLOCK. However, if the minimum hold time for DOUT is acceptable, the system can use the falling edge of DCLOCK to capture each bit. DESCRIPTION MIN tSMPL SYMBOL Analog Input Sample TIme 1.5 TYP MAX UNITS 2.0 Clk Cycles tCONV Conversion Time tCYC Throughput Rate 200 kHz tCSD CS Falling to DCLOCK LOW 0 ns tSUCS CS Falling to DCLOCK Rising 30 ns thDO DCLOCK Falling to Current DOUT Not Valid 15 ns tdDO DCLOCK Falling to Next DOUT Valid 85 tdis CS Rising to DOUT Tri-State ten DCLOCK Falling to DOUT Enabled tf tr 12 Clk Cycles 150 ns 25 50 ns 50 100 ns DOUT Fall Time 70 100 ns DOUT Rise Time 60 100 ns TABLE I. Timing Specifications –40°C to +85°C. 9 tCYC CS/SHDN POWER DOWN tSUCS DCLOCK tCSD DOUT HI-Z NULL BIT tSMPL NULL BIT HI-Z B11 B10 B9 (MSB) B8 B7 B6 B5 B4 B3 B2 B1 B0(1) tCONV B11 B10 B9 B8 tDATA Note: (1) After completing the data transfer, if further clocks are applied with CS LOW, the A/D will output LSB-First data then followed with zeroes indefinitely. tCYC CS/SHDN tSUCS POWER DOWN DCLOCK tCSD DOUT HI-Z NULL BIT tSMPL HI-Z B11 B10 B9 (MSB) B8 B7 B6 B5 B4 B3 B2 B1 B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 (2) tCONV tDATA Note: (2) After completing the data transfer, if further clocks are applied with CS LOW, the A/D will output zeroes indefinitely. tDATA: During this time, the bias current and the comparator power down and the reference input becomes a high impedance node, leaving the CLK running to clock out LSB-First data or zeroes. FIGURE 4. ADS7817 Basic Timing Diagrams. A falling CS signal initiates the conversion and data transfer. The first 1.5 to 2.0 clock periods of the conversion cycle are used to sample the input signal. After the second falling DCLOCK edge, DOUT is enabled and will output a LOW value for one clock period. For the next 12 DCLOCK periods, DOUT will output the conversion result, most significant bit first. After the least significant bit (B0) has been output, subsequent clocks will repeat the output data but in a least significant bit first format. After the most significant bit (B11) has been repeated, DOUT will tri-state. Subsequent clocks will have no effect on the converter. A new conversion is initiated only when CS has been taken HIGH and returned LOW. DATA FORMAT The output data from the ADS7817 is in Binary Two’s Complement format as shown in Table II. This table represents the ideal output code for the given input voltage and does not include the effects of offset, gain error, or noise. DESCRIPTION Full Scale Input Span ANALOG VALUE 2 • VREF DIGITAL OUTPUT: BINARY TWO’S COMPLEMENT Least Significant Bit (LSB) 2 • VREF/4096 BINARY CODE HEX CODE +Full Scale VREF –1 LSB 0111 1111 1111 7FF 0V 0000 0000 0000 000 0V – 1 LSB 1111 1111 1111 FFF –VREF 1000 0000 0000 800 Midscale Midscale – 1 LSB –Full Scale POWER DISSIPATION The architecture of the converter, the semiconductor fabrication process, and a careful design allow the ADS7817 to convert at up to a 200kHz rate while requiring very little power. Still, for the absolute lowest power dissipation, there are several things to keep in mind. The power dissipation of the ADS7817 scales directly with conversion rate. The first step to achieving the lowest power dissipation is to find the lowest conversion rate that will satisfy the requirements of the system. In addition, the ADS7817 is in power down mode under two conditions: when the conversion is complete and whenever CS is HIGH (see Figure 1). Ideally, each conversion should occur as quickly as possible, preferably, at a 3.2MHz clock rate. This way, the converter spends the longest possible time in the power down mode. This is very important as the converter not only uses power on each DCLOCK transition (as is typical for digital CMOS components) but also uses some current for the analog circuitry, such as the comparator. The analog section dissipates power continuously, until the power down mode is entered. Figure 6 shows the current consumption of the ADS7817 versus sample rate. For this graph, the converter is clocked at 3.2MHz regardless of the sample rate—CS is HIGH for the remaining sample period. Figure 7 also shows current consumption versus sample rate. However, in this case, the DCLOCK period is 1/16th of the sample period—CS is HIGH for one DCLOCK cycle out of every 16. TABLE II. Ideal Input Voltages and Output Codes. 10 ADS7817 SBAS066A 1.4V 3kΩ VOH DOUT DOUT VOL Test Point tr 100pF CLOAD tf Voltage Waveforms for DOUT Rise and Fall Times tr, and tf Load Circuit for tdDO, tr, and tf Test Point DCLOCK VIL VCC tdDO VOH DOUT tdis Waveform 2, ten 3kΩ DOUT tdis Waveform 1 100pF CLOAD VOL thDO Load Circuit for tdis and tden Voltage Waveforms for DOUT Delay Times, tdDO VIH CS/SHDN DOUT Waveform 1(1) CS/SHDN 90% DCLOCK 10% DOUT 1 2 tdis DOUT Waveform 2(2) VOL B11 ten Voltage Waveforms for tdis NOTES: (1) Waveform 1 is for an output with internal conditions such that the output is HIGH unless disabled by the output control. (2) Waveform 2 is for an output with internal conditions such that the output is LOW unless disabled by the output control. Voltage Waveforms for ten FIGURE 5. Timing Diagrams and Test Circuits for the Parameters in Table I. 1000 Supply Current (µA) Supply Current (µA) 1000 100 10 TA = 25°C VCC = +5V VREF = +2.5V fCLK = 3.2MHz 1 100 10 TA = 25°C VCC = +5V VREF = +2.5V fCLK = 16 • fSAMPLE 1 1 10 100 1000 Sample Rate (kHz) FIGURE 6. Maintaining fCLK at the Highest Possible Rate Allows Supply Current to Drop Directly with Sample Rate. ADS7817 SBAS066A 1 10 100 1000 Sample Rate (kHz) FIGURE 7. Scaling fCLK Reduces Supply Current Only Slightly with Sample Rate. 11 There is an important distinction between the power down mode that is entered after a conversion is complete and the full power down mode which is enabled when CS is HIGH. While both power down the analog section, the digital section is powered down only when CS is HIGH. Thus, if CS is left LOW at the end of a conversion and the converter is continually clocked, the power consumption will not be as low as when CS is HIGH. See Figure 8 for more information. By lowering the reference voltage, the ADS7817 requires less current to completely charge its internal capacitors on both the analog input and the reference input. This reduction in power dissipation should be weighed carefully against the resulting increase in noise, offset, and gain error as outlined in the Reference section. 60 TA = 25°C VCC = +5V VREF = +2.5V fCLK = 16 • fSAMPLE Supply Current (µA) 50 40 CS LOW (GND) 30 20 CS = HIGH (VCC) 10 0 1 10 100 1000 Sample Rate (kHz) FIGURE 8. Shutdown Current is Considerably Lower with CS HIGH than when CS is LOW. SHORT CYCLING Another way of saving power is to utilize the CS signal to short cycle the conversion. Because the ADS7817 places the latest data bit on the DOUT line as it is generated, the converter can easily be short cycled. This term means that the conversion can be terminated at any time. For example, if only 8-bits of the conversion result are needed, then the conversion can be terminated (by pulling CS HIGH) after the 8th bit has been clocked out. This technique can be used to lower the power dissipation in those applications where an analog signal is being monitored until some condition becomes true. For example, if the signal is outside a predetermined range, the full 12-bit conversion result may not be needed. If so, the conversion can be terminated after the first n-bits, where n might be as low as 3 or 4. This results in lower power dissipation in both the converter and the rest of the system, as they spend more time in the power down mode. 12 LAYOUT For optimum performance, care should be taken with the physical layout of the ADS7817 circuitry. This is particularly true if the reference voltage is low and/or the conversion rate is high. At 200kHz conversion rate, the ADS7817 makes a bit decision every 312ns. That is, for each subsequent bit decision, the digital output must be updated with the results of the last bit decision, the capacitor array appropriately switched and charged, and the input to the comparator settled to a 12-bit level all within one clock cycle. The basic SAR architecture is sensitive to spikes on the power supply, reference, and ground connections that occur just prior to latching the comparator output. Thus, during any single conversion for an n-bit SAR converter, there are n “windows” in which large external transient voltages can easily affect the conversion result. Such spikes might originate from switching power supplies, digital logic, and high power devices, to name a few. This particular source of error can be very difficult to track down if the glitch is almost synchronous to the converter’s DCLOCK signal—as the phase difference between the two changes with time and temperature, causing sporadic misoperation. With this in mind, power to the ADS7817 should be clean and well bypassed. A 0.1µF ceramic bypass capacitor should be placed as close to the ADS7817 package as possible. In addition, a 1 to 10µF capacitor and a 10Ω series resistor may be used to lowpass filter a noisy supply. The reference should be similarly bypassed with a 0.1µF capacitor. Again, a series resistor and large capacitor can be used to lowpass filter the reference voltage. If the reference voltage originates from an op amp, be careful that the opamp can drive the bypass capacitor without oscillation (the series resistor can help in this case). Keep in mind that while the ADS7817 draws very little current from the reference on average, there are higher instantaneous current demands placed on the external reference circuitry. Also, keep in mind that the ADS7817 offers no inherent rejection of noise or voltage variation in regards to the reference input. This is of particular concern when the reference voltage is derived from the power supply. Any noise and ripple from the supply that is not rejected by the external reference circuitry will appear directly in the digital results. While high frequency noise can be filtered out as described in the previous paragraph, voltage variation due to line frequency (50Hz or 60Hz) can be difficult to remove. The GND pin on the ADS7817 should be placed on a clean ground point. In many cases, this will be the “analog” ground. Avoid connecting the GND pin too close to the grounding point for a microprocessor, microcontroller, or digital signal processor. If needed, run a ground trace directly from the converter to the power supply connection point. The ideal layout will include an analog ground plane for the converter and associated analog circuitry. ADS7817 SBAS066A APPLICATION CIRCUITS Figures 9, 10 and 11 show some typical applications circuits for the ADS7817. Figure 9 shows a low cost, low power circuit for basic data acquisition. Total power dissipation in the ADS7817 and reference circuitry is under 5mW over temperature, power supply variations, and at a 200kHz sample rate. Figure 11 is a similar application that isolates the digital outputs of the three ADS7817s instead of the analog signal from the motor. Here, the reference voltage for the ADS7817 is 150mV, and the analog input of each ADS7817 is connected directly to the current sense resistor. By removing the ISO130 from the signal path, a greater signal-to-noise ratio is achieved in the sensing system. However, nine optical isolators are needed to isolate the A/D converters. Figure 10 is a motor control application using three ISO130s to isolate the motor from the sensing system (three ADS7817s and a DSP56004). The ISO130 provides 10kV/µs (minimum) isolation-mode rejection, 85kHz large signal bandwidth, and a fixed gain of 8. The ADS7817’s reference voltage is 1.2V and is derived from a REF1004-1.2. This gives the converter a full-scale input range of ±1.2V. Because of the gain of 8 in the ISO130, the current sense resistor should give a worstcase output voltage of less than ±150mV. +5V 5Ω to 10Ω + 1µF to 10µF 24.9kΩ 22Ω REF1004-2.5 + ADS7817 VREF 4.7µF VCC 0.1µF +In CS –In DOUT GND + 1µF to 10µF Microcontroller DCLOCK FIGURE 9. Low Cost, Low Power Data Acquisition System. ADS7817 SBAS066A 13 +5V R1 1kΩ +VISO3 78L05 REF1004-1.2 Motorola DSPS6004 C10 5µF C1 C2 0.1µF GND3 0.1µF + C11 0.1µF +5V WST WSR R2 200Ω to 3rd Motor Leg Driver DOUT C3 0.01µF ISO130 ADS7817 CLK SDI 0 CS/SHDN R3 200Ω System GND System GND +5V GND3 +VISO2 R4 1kΩ 78L05 SCKR SCK/SCL REF1004-1.2 C12 5µF C4 C5 0.1µF GND2 0.1µF + C13 0.1µF +5V R5 200Ω to 2nd Motor Leg Driver CS/SHDN System GND System GND from PWM ••• +5V GND2 +VISO1 R7 1kΩ 78L05 REF1004-1.2 C14 5µF C8 C7 0.1µF GND1 0.1µF + C15 0.1µF +5V R8 200Ω 0.01µF – System GND RSENSE HV– (Several Hundred Volts) ADS7817 R9 200Ω R10 + CLK C9 0.01µF ISO130 AC Motor ••• SDI 1 CLK ADS7817 R6 200Ω First Motor Leg Driver HV+ (Several Hundred Volts) DOUT C6 0.01µF ISO130 ••• from PWM CS/SHDN DOUT SCKT SDO 0 MOSI/HA 0 SD02 System GND SS/HA2 System GND GND1 FIGURE 10. Motor Control Using the ISO130, ADS7817, and DSPS6004. 14 ADS7817 SBAS066A +VISO1 R1 +5V +VCC Motorola DSP56004 R2 768Ω + C 1 4.7µF R3 301Ω REF1004-1.2 WST +150mV VREF + C 2 4.7µF R4 43.2Ω C3 0.1µF To 3rd Motor Leg SDO0 SDO1 SDO2 SCKT SCKR SDI0 To 2nd Motor Leg SDI1 WSR SCK/SCL MISO/SDA VREF +VCC from PWM HREQ R5 200Ω AC Motor MOSI/HA0 SS/HA2 C4 0.01µF RSENSE ADS7817 CS DOUT CLK R6 200Ω from PWM Opto-Couplers(1) 1st Motor Leg NOTE: (1) Suggested Opto-couplers are HCPL-2611 or HCPL-7611. Inverters or buffers will be needed to drive these devices. See the appropriate Hewlett-Packard data sheet for more information. FIGURE 11. Motor Control Using an Isolated ADS7817. ADS7817 SBAS066A 15 PACKAGE OPTION ADDENDUM www.ti.com 16-Aug-2012 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) (Requires Login) ADS7817E/250 ACTIVE VSSOP DGK 8 250 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-1-260C-UNLIM ADS7817E/250G4 ACTIVE VSSOP DGK 8 250 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-1-260C-UNLIM ADS7817E/2K5 ACTIVE VSSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-1-260C-UNLIM ADS7817E/2K5G4 ACTIVE VSSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-1-260C-UNLIM ADS7817EB/250 ACTIVE VSSOP DGK 8 250 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-1-260C-UNLIM ADS7817EB/250G4 ACTIVE VSSOP DGK 8 250 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-1-260C-UNLIM ADS7817EB/2K5 ACTIVE VSSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-1-260C-UNLIM ADS7817EB/2K5G4 ACTIVE VSSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-1-260C-UNLIM ADS7817EC/250 ACTIVE VSSOP DGK 8 250 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-1-260C-UNLIM ADS7817EC/250G4 ACTIVE VSSOP DGK 8 250 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-1-260C-UNLIM ADS7817EC/2K5 ACTIVE VSSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-1-260C-UNLIM ADS7817EC/2K5G4 ACTIVE VSSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-1-260C-UNLIM ADS7817P OBSOLETE PDIP P 8 TBD Call TI Call TI ADS7817PB OBSOLETE PDIP P 8 TBD Call TI Call TI ADS7817PC OBSOLETE PDIP P 8 TBD Call TI Call TI ADS7817U ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR ADS7817U/2K5 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR ADS7817U/2K5G4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 16-Aug-2012 Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) ADS7817UB ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR ADS7817UBG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR ADS7817UC ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR ADS7817UC/2K5 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR ADS7817UC/2K5G4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR ADS7817UCG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR ADS7817UG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Samples (Requires Login) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. Addendum-Page 2 PACKAGE OPTION ADDENDUM www.ti.com 16-Aug-2012 In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 3 PACKAGE MATERIALS INFORMATION www.ti.com 16-Aug-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant ADS7817E/250 VSSOP DGK 8 250 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 ADS7817E/2K5 VSSOP DGK 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 ADS7817EB/250 VSSOP DGK 8 250 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 ADS7817EB/2K5 VSSOP DGK 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 ADS7817EC/250 VSSOP DGK 8 250 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 ADS7817EC/2K5 VSSOP DGK 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 ADS7817U/2K5 SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 ADS7817UC/2K5 SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 16-Aug-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) ADS7817E/250 VSSOP DGK 8 250 367.0 367.0 35.0 ADS7817E/2K5 VSSOP DGK 8 2500 367.0 367.0 35.0 ADS7817EB/250 VSSOP DGK 8 250 367.0 367.0 35.0 ADS7817EB/2K5 VSSOP DGK 8 2500 367.0 367.0 35.0 ADS7817EC/250 VSSOP DGK 8 250 367.0 367.0 35.0 ADS7817EC/2K5 VSSOP DGK 8 2500 367.0 367.0 35.0 ADS7817U/2K5 SOIC D 8 2500 367.0 367.0 35.0 ADS7817UC/2K5 SOIC D 8 2500 367.0 367.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2012, Texas Instruments Incorporated