MPP10(W) MPP10(W) SERIES DC-DC CONVERTER 2:1 & 4:1 WIDE INPUT RANGE UP TO 10.05 WATTS FEATURES APPLICATIONS • REINFORCED INSULATION FOR 250VAC WORKING VOLTAGE • CLEARANCE AND CREEPAGE DISTANCE :8.0mm/2MOPP • 5000VAC INPUT TO OUTPUT 2MOPP ISOLATION • BUILT-IN EMI CLASS A FILTER • 2µA PATIENT LEAKAGE CURRENT • SAFETY MEETS ANSI/AAMI ES60601-1, EN60601-1 AND IEC60601-1 • CE MARK MEETS 2006/95/EC, 2011/95/EC AND 2004/108/EC • COMPLIANT TO RoHS EU DIRECTIVE 2011/65/EU 5000VAC ISOLATION UVP OCP MEDICAL EQUIPMENT TELECOM/DATACOM INDUSTRY CONTROL SYSTEM MEASUREMENT EQUIPMENT SEMICONDUCTOR EQUIPMENT PV POWER SYSTEM IGBT GATE DRIVER LOW STANDBY POWER OVP SCP TECHNICAL SPECIFICATION All specifications are typical at nominal input, full load and 25ºC otherwise noted Model Number MPP10-05S3P3A/B MPP10-05S05A/B MPP10-05S12A/B MPP10-05S15A/B MPP10-05S24A/B MPP10-05D05A/B MPP10-05D12A/B MPP10-05D15A/B MPP10-12S3P3A/B MPP10-12S05A/B MPP10-12S12A/B MPP10-12S15A/B MPP10-12S24A/B MPP10-12D05A/B MPP10-12D12A/B MPP10-12D15A/B MPP10-24S3P3A/B MPP10-24S05A/B MPP10-24S12A/B MPP10-24S15A/B MPP10-24S24A/B MPP10-24D05A/B MPP10-24D12A/B MPP10-24D15A/B MPP10-48S3P3A/B MPP10-48S05A/B MPP10-48S12A/B MPP10-48S15A/B MPP10-48S24A/B MPP10-48D05A/B MPP10-48D12A/B MPP10-48D15A/B Page 1 of 4 Input Range Output Voltage Output Current @ Full Load Input Current @ No Load Efficiency Maximum Capacitor Load VDC 4.5 ~9 4.5 ~9 4.5 ~9 4.5 ~9 4.5 ~9 4.5 ~9 4.5 ~9 4.5 ~9 9 ~ 18 9 ~ 18 9 ~ 18 9 ~ 18 9 ~ 18 9 ~ 18 9 ~ 18 9 ~ 18 18 ~ 36 18 ~ 36 18 ~ 36 18 ~ 36 18 ~ 36 18 ~ 36 18 ~ 36 18 ~ 36 36 ~ 75 36 ~ 75 36 ~ 75 36 ~ 75 36 ~ 75 36 ~ 75 36 ~ 75 36 ~ 75 VDC 3.3 5 12 15 24 ±5 ±12 ±15 3.3 5 12 15 24 ±5 ±12 ±15 3.3 5 12 15 24 ±5 ±12 ±15 3.3 5 12 15 24 ±5 ±12 ±15 mA 2500 2000 830 670 416 ±1000 ±416 ±333 2500 2000 830 670 416 ±1000 ±416 ±333 2500 2000 830 670 416 ±1000 ±416 ±333 2500 2000 830 670 416 ±1000 ±416 ±333 mA 10 10 15 15 20 25 25 25 10 10 10 10 10 10 10 10 6 6 6 6 6 6 6 6 4 4 4 4 4 4 4 4 % 80 84 86.5 87 85.5 83 85.5 86.5 83 85.5 88 89 89 84 89 88 83 86.5 89 89 89 85 89 88 82.5 86.5 89 89 88.5 85 88 88 µF 3000 2500 430 350 125 ± 1440 ± 250 ± 180 3000 2500 430 350 125 ± 1440 ± 250 ± 180 3000 2500 430 350 125 ± 1440 ± 250 ± 180 3000 2500 430 350 125 ± 1440 ± 250 ± 180 www.pduke.com 2013/7/9 MPP10(W) Model Number Input Range Output Voltage Output Current @ Full Load Input Current @ No Load Efficiency Maximum Capacitor Load VDC 9 ~ 36 9 ~ 36 9 ~ 36 9 ~ 36 9 ~ 36 9 ~ 36 9 ~ 36 9 ~ 36 18 ~ 75 18 ~ 75 18 ~ 75 18 ~ 75 18 ~ 75 18 ~ 75 18 ~ 75 18 ~ 75 VDC 3.3 5 12 15 24 ±5 ±12 ±15 3.3 5 12 15 24 ±5 ±12 ±15 mA 2500 2000 830 670 416 ±1000 ±416 ±333 2500 2000 830 670 416 ±1000 ±416 ±333 mA 6 6 6 6 6 6 6 6 4 4 4 4 4 4 4 4 % 83 86.5 89 89 89 85 89 88 82.5 86.5 89 89 88.5 85 88 88 µF 3000 2500 430 350 125 ± 1440 ± 250 ± 180 3000 2500 430 350 125 ± 1440 ± 250 ± 180 P T Remote On/Off Option Trim Option MPP10-24S3P3WA/B MPP10-24S05WA/B MPP10-24S12WA/B MPP10-24S15WA/B MPP10-24S24WA/B MPP10-24D05WA/B MPP10-24D12WA/B MPP10-24D15WA/B MPP10-48S3P3WA/B MPP10-48S05WA/B MPP10-48S12WA/B MPP10-48S15WA/B MPP10-48S24WA/B MPP10-48D05WA/B MPP10-48D12WA/B MPP10-48D15WA/B PART NUMBER STRUCTURE MPP10 - Series Name 48 S 05 W A Input Voltage (VDC) Output Quantity Output Voltage (VDC) Input Range Pin Connection Option 4.5~9 9~18 18~36 36~75 S: Single 3.3 5 12 15 24 : 2:1 W: 4:1 A: A type(Standard) B: B type 05: 12: 24: 48: 3P3: 05: 12: 15: 24: D: Dual W: 24: 9~36 48: 18~75 INPUT SPECIFICATIONS Parameter 2:1 (W) 4:1 Start-up voltage 2:1 (W) 4:1 Shutdown voltage 2:1 (W) 4:1 Start up time Input surge voltage Input filter Remote ON/OFF (Only for B-type Pin connection option) Page 2 of 4 Constant resistive load 3 second, max. 2:1 3 second, max. (W) 4:1 Referenced to - INPUT pin : No On/Off control : No Trim P: Remote On/Off T: Trim (Only for B type (Only for B type Pin connection) Pin connection) 05: ±5 12: ±12 15: ±15 Conditions Operating input voltage range - 5Vin(nom) 12Vin(nom) 24Vin(nom) 48Vin(nom) 24Vin(nom) 48Vin(nom) 5Vin(nom) 12Vin(nom) 24Vin(nom) 48Vin(nom) 24Vin(nom) 48Vin(nom) 5Vin(nom) 12Vin(nom) 24Vin(nom) 48Vin(nom) 24Vin(nom) 48Vin(nom) Power up Remote ON/OFF 5Vin(nom) 12Vin(nom) 24Vin(nom) 48Vin(nom) 24Vin(nom) 48Vin(nom) DC-DC ON DC-DC OFF Input current of CTRL pin Remote off input current www.pduke.com Min. Typ. Max. 4.5 9 18 36 9 18 5 12 24 48 24 48 9 18 36 75 36 75 4.5 9 18 36 9 18 4 8 16 33 8 16 30 30 -0.5 Unit VDC VDC VDC VDC VDC VDC ms 16 25 VDC 50 100 50 VDC 100 Pi type OPEN or 0 ~ 1.2VDC 2.2 ~ 12VDC 1 mA 2.5 mA 2013/7/9 MPP10(W) OUTPUT SPECIFICATIONS Parameter Voltage accuracy Line regulation Load regulation Cross regulation Voltage adjustability Conditions Low Line to High Line at Full Load No Load to Full Load Asymmetrical load 25%/100% FL Single output (Only for B-type Pin connection option) Ripple and noise Dual output Measured by 20MHz bandwidth With a 10µF/25V X7R MLCC With a 4.7µF/50V X7R MLCC Temperature coefficient Transient response recovery time Over voltage protection Single Dual Single Dual Dual 3.3Vout, 5Vout, 12Vout 15Vout, 24Vout ±5Vout, ±12Vout, ±15Vout 3.3Vout, 5Vout 12Vout, 15Vout 24Vout 3.3Vout 5Vout 12Vout 15Vout 24Vout 1 minute Storage temperature range Thermal impedance Thermal shock Vibration Relative humidity EMC SPECIFICATIONS Parameter EMI (1) ESD Radiated immunity Fast transient (2) Surge (2) Conducted immunity Unit % % % % % % mVp-p +0.02 250 3.7 5.6 13.5 18.3 29.1 % of Iout rated; Hiccup mode 5.4 7.0 19.6 22.0 32.5 %/ºC µs VDC 150 % Continuous, automatics recovery Conditions Min. Input to Output 5000 240VAC,60Hz 270 8 MIL-HDBK-217F Ta=25ºC, Full load (G/B, controlled environment) ENVIRONMENTAL SPECIFICATIONS Parameter Operating ambient temperature +1.0 +0.2 +0.5 +0.2 +1.0 +5.0 +10 +20 +10 30 40 50 Case material Base material Potting material Dimensions Weight MTBF Max. -0.02 GENERAL SPECIFICATIONS Parameter Isolation voltage Isolation capacitance Leakage current Switching frequency Clearance/Creepage Design meet safety standard Typ. -1.0 -0.2 -0.5 -0.2 -1.0 -5.0 -10 -10 -10 25% load step change Continuous clamp Over load protection Short circuit protection Min. Conditions Without derating With derating Min. , Natural convection (20LFM) Typ. Max. VAC pF µA 300 kHz mm ANSI/AAMI ES60601-1 IEC60601-1, EN60601-1 Non-conductive black plastic Non-conductive black plastic Silicon (UL94-V0) 1.25 X 0.80 X 0.40 Inch (31.8×20.3×10.2 mm) 14g (0.48oz) 8.638 x 105 hrs 12 17 2 330 Typ. Max. -40 +77 -55 Unit +77 +105 +125 ºC ºC ºC ºC/W MIL-STD-810F MIL-STD-810F 5% to 95% RH 18 Conditions Unit Level EN55011,EN55022 and FCC Part 18 Air ± 8kV EN61000-4-2 Contact ± 6kV EN61000-4-3 10 V/m EN61000-4-4 ± 2kV EN61000-4-5 ± 2kV EN61000-4-6 10 Vr.m.s Class A, Class B Perf. Criteria A Perf. Criteria A Perf. Criteria A Perf. Criteria A Perf. Criteria A Note: The MPP10(W) series can meet EMI Class A with no external filter. And Class B only with external components. For more detail information, please contact with P-DUKE. 2. An external input filter capacitor is required if the module has to meet EN61000-4-4, EN61000-4-5. The MPP10-05S recommended an aluminum electrolytic capacitor (Nippon Chemi-con KY series, 1000µF/25V). And a reverse diode (Vishay V10P45) to connect in parallel. The MPP10-12&24S recommended an aluminum electrolytic capacitor (Nippon Chemi-con KY series, 470µF/50V). The MPP10-48S recommended an aluminum electrolytic capacitor (Nippon Chemi-con KY series, 330µF/100V). CAUTION: This power module is not internally fused. An input line fuse must always be used. 1. Page 3 of 4 www.pduke.com 2013/7/9 MPP10(W) CHARACTERISTIC CURVE MPP10-48S05WA Derating Curve MPP10-48S05WA Efficiency VS Input Voltage MPP10-48S05WA Efficiency VS Output Load MECHANICAL DRAWING A type Pin connection (Standard) DIP PIN CONNECTION PIN SINGLE DUAL 1 + INPUT + INPUT 11 NO PIN COMMON 12 13 -OUTPUT +OUTPUT NO PIN -OUTPUT 15 NO PIN +OUTPUT 23 - INPUT - INPUT 24 - INPUT - INPUT 1. All dimensions in Inch (mm) Tolerance: X.XX±0.02 (X.X±0.5) X.XXX±0.01 (X.XX±0.25) 2. Pin pitch tolerance ±0.01 (0.25) 3. Pin dimension tolerance ±0.004 (0.1) B type Pin connection DIP PIN CONNECTION PIN SINGLE DUAL 1 2 CTRL (Option) - INPUT CTRL (Option) - INPUT 10 11 TRIM (Option) NO PIN / NC (＊＊) TRIM (Option) -OUTPUT 14 +OUTPUT +OUTPUT 16 -OUTPUT COMMON 22 +INPUT +INPUT 23 +INPUT +INPUT ＊＊： 1. The Pin 11 is ”NO PIN” when single output with Trim option (Suffix: -T). The Pin 11 is ”NC” when single output without TRIM pin. All dimensions in Inch (mm) Tolerance: X.XX±0.02 (X.X±0.5) X.XXX±0.01 (X.XX±0.25) Page 4 of 4 www.pduke.com 2. Pin pitch tolerance ±0.01 (0.25) 3. Pin dimension tolerance ±0.004 (0.1) 2013/7/9