Multilayer ceramic capacitors are available in a variety of physical sizes and configurations, including leaded devices and surface mounted chips. Leaded styles include molded and conformally coated parts with axial and radial leads. However, the basic capacitor element is similar for all styles. It is called a chip and consists of formulated dielectric materials which have been cast into thin layers, interspersed with metal electrodes alternately exposed on opposite edges of the laminated structure. The entire structure is fired at high temperature to produce a monolithic block which provides high capacitance values in a small physical volume. After firing, conductive terminations are applied to opposite ends of the chip to make contact with the exposed electrodes. Termination materials and methods vary depending on the intended use. TEMPERATURE CHARACTERISTICS Class III: General purpose capacitors, suitable Ceramic dielectric materials can be formulated with a wide range of characteristics. The EIA standard for for by-pass coupling or other applications in which ceramic dielectric capacitors (RS-198) divides ceramic dielectric losses, high insulation resistance and dielectrics into the following classes: stability of capacitance characteristics are of little or no importance. Class III capacitors are similar to Class II capacitors except for temperature characteristics, Class I: Temperature compensating capacitors, which are greater than ± 15%. Class III capacitors suitable for resonant circuit application or other applihave the highest volumetric efficiency and poorest cations where high Q and stability of capacitance charstability of any type. acteristics are required. Class I capacitors have predictable temperature coefficients and are not effected by voltage, frequency or time. They are made KEMET leaded ceramic capacitors are offered in from materials which are not ferro-electric, yielding the three most popular temperature characteristics: superior stability but low volumetric efficiency. Class I C0G: Class I, with a temperature coefficient of 0 ± capacitors are the most stable type available, but have 30 ppm per degree C over an operating the lowest volumetric efficiency. temperature range of - 55°C to + 125°C (Also known as “NP0”). X7R: Class II, with a maximum capacitance Class II: Stable capacitors, suitable for bypass change of ± 15% over an operating temperature or coupling applications or frequency discriminating range of - 55°C to + 125°C. circuits where Q and stability of capacitance charZ5U: Class III, with a maximum capacitance acteristics are not of major importance. Class II change of + 22% - 56% over an operating temcapacitors have temperature characteristics of ± 15% perature range of + 10°C to + 85°C. or less. They are made from materials which are ferro-electric, yielding higher volumetric efficiency but less stability. Class II capacitors are affected by Specified electrical limits for these three temperature temperature, voltage, frequency and time. characteristics are shown in Table 1. SPECIFIED ELECTRICAL LIMITS TEMPERATURE CHARACTERISTICS C0G X7R Z5U PARAMETER Dissipation Factor: Measured at following conditions: C0G — 1 kHz and 1 vrms if capacitance > 1000 pF 1 MHz and 1 vrms if capacitance ≤ 1000 pF X7R — 1 kHz and 1 vrms* or if extended cap range 0.5 vrms Z5U — 1 kHz and 0.5 vrms Dielectric Strength: 2.5 times rated DC voltage. 0.15% 2.5% 4.0% Pass Subsequent IR Test Insulation Resistance (IR): At rated DC voltage, whichever of the two is smaller 1,000 MΩ-µF or 100 GΩ 1,000 MΩ-µF or 100 GΩ 1,000 MΩ-µF or 10 GΩ Temperature Characteristics: Range, °C Capacitance Change without DC voltage -55 to +125 0 ± 30 ppm/°C -55 to +125 ±15% +10 to +85 +22%, -56% * 1 MHz and 1 vrms if capacitance ≤ 100 pF on military product. Table I © KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 3 Multlayer Ceramic Capacitors MULTILAYER CERAMIC CAPACITORS/AXIAL & RADIAL LEADED CERAMIC CONFORMALLY COATED/AXIAL & RADIAL PERFORMANCE CHARACTERISTICS FOR STANDARD AND HIGH VOLTAGE GENERAL SPECIFICATIONS Working Voltage: Axial (WVDC) C0G – 50 & 100 X7R – 50 & 100 Z5U – 50 & 100 ENVIRONMENTAL Vibration: EIA RS-198, Method 304, Condition D (10-2000Hz; 20g) Shock: EIA RS-198, Method 305, Condition I (100g) Radial (WVDC) 50, 100, 200, 500, 1k, 1.5k, 2k, 2.5k, 3k 50, 100, 200, 500, 1k, 1.5k, 2k, 2.5k, 3k 50 & 100 Life Test: EIA RS-198, Method 201, Condition D. £ 200V C0G – 200% of rated voltage @ +125°C X7R – 200% of rated voltage @ +125°C Z5U – 200% of rated voltage @ +85°C ³ 500V C0G – rated voltage @ +125°C X7R – rated voltage @ +125°C Temperature Characteristics: C0G – 0 ± 30 PPM / °C from - 55°C to + 125°C (1) X7R – ± 15% from - 55°C to + 125°C Z5U – + 22% / -56% from + 10°C to + 85°C Capacitance Tolerance: C0G – ±0.5pF, ±1%, ±2%, ±5%, ±10% X7R – ±10%, ±20%, +80% / -20%, +100% / -0% Z5U – ±20%, +80% / -20% Post Test Limits @ 25°C are: Capacitance Change: C0G (£ 200V) – +3% or 0.25pF, whichever is greater. C0G (³ 500V) – +3% or 0.50pF, whichever is greater. X7R – + 20% of initial value (2) Z5U – + 30% of initial value (2) Dissipation Factor: C0G – 0.15% maximum X7R – 2.5% maximum Z5U – 4.0% maximum Insulation Resistance: C0G – 10k Megohm or 100 Megohm x µF, whichever is less. ³1kV tested @ 500V. X7R – 10k Megohm or 100 Megohm x µF, whichever is less. ³1kV tested @ 500V. Z5U – 1k Megohm or 100 Megohm x µF, whichever is less. Construction: Epoxy encapsulated - meets flame test requirements of UL Standard 94V-0. High-temperature solder - meets EIA RS-198, Method 302, Condition B (260°C for 10 seconds) Lead Material: 100% matte tin (Sn) with nickel (Ni) underplate and steel core. Solderability: EIA RS-198, Method 301, Solder Temperature: 230°C ±5°C. Dwell time in solder = 7 ± ½ seconds. Terminal Strength: EIA RS-198, Method 303, Condition A (2.2kg) Moisture Resistance: EIA RS-198, Method 204, Condition A (10 cycles without applied voltage.) Post Test Limits @ 25°C are: Capacitance Change: C0G (£ 200V) – +3% or 0.25pF, whichever is greater. C0G (³ 500V) – +3% or 0.50pF, whichever is greater. X7R – + 20% of initial value (2) Z5U – + 30% of initial value (2) Dissipation Factor: C0G – 0.25% maximum X7R – 3.0% maximum Z5U – 4.0% maximum Insulation Resistance: C0G – 10k Megohm or 100 Megohm x µF, whichever is less. £500V test @ rated voltage, ³1kV test @ 500V. X7R – 10k Megohm or 100 Megohm x µF, whichever is less. ³500V test @ rated voltage, >1kV test @ 500V. Z5U – 1k Megohm or 100 Megohm x µF, whichever is less. ELECTRICAL Capacitance @ 25°C: Within specified tolerance and following test conditions. C0G – > 1000pF with 1.0 vrms @ 1 kHz £ 1000pF with 1.0 vrms @ 1 MHz X7R – with 1.0 vrms @ 1 kHz Z5U – with 1.0 vrms @ 1 kHz Dissipation Factor @ 25°C: Same test conditions as capacitance. C0G – 0.15% maximum X7R – 2.5% maximum Z5U – 4.0% maximum Insulation Resistance @ 25°C: EIA RS-198, Method 104, Condition A <1kV C0G – 100k Megohm or 1000 Megohm x µF, whichever is less. £500V test @ rated voltage, ³1kV test @ 500V X7R – 100k Megohm or 1000 Megohm x µF, whichever is less. £500V test @ rated voltage, ³1kV test @ 500V Z5U – 10k Megohm or 1000 Megohm x µF, whichever is less. Dielectric Withstanding Voltage: EIA RS-198, Method 103 £200V test @ 250% of rated voltage for 5 seconds with current limited to 50mA. 500V test @ 150% of rated voltage for 5 seconds with current limited to 50mA. ³1000V test @ 120% of rated voltage for 5 seconds with current limited to 50mA. 4 Thermal Shock: EIA RS-198, Method 202, Condition B (C0G & X7R: -55°C to +125°C); Condition A (Z5U: -55°C to 85°C) (1) (2) +53 PPM -30 PPM/ °C from +25°C to -55°C, + 60 PPM below 10pF. X7R and Z5U dielectrics exhibit aging characteristics; therefore, it is highly recommended that capacitors be deaged for 2 hours at 150°C and stabilized at room temperature for 48 hours before capacitance measurements are made. © KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 CERAMIC CONFORMALLY COATED/RADIAL HIGH VOLTAGE “GOLDEN MAX” CAPACITOR OUTLINE DRAWING L C617 C622 C627 C630 C637 C640 C642 C647 C657 C667 L C623 C628 C631 C638 C641 C643 C648 C658 C668 H D * S H D ** S * .276 (7.00) Min. DIMENSIONS - INCHES AND MILLIMETERS Case Size L MAX H MAX T MAX. Lead Spacing LD (Nominal) inches (mm) inches (mm) inches (mm) inches (mm) inches (mm) C617 .250 (6.35) .220 (5.59) .200 (5.08) .170 (4.32) .025 (.64) C622/3 .320 (8.13) .280(7.11) .250 (6.35) .220 (5.59) .025 (.64) C627/8 .370 (9.40) .300 (7.62) .250 (6.35) .275 (6.98) .025 (.64) C630/1 .450 (11.40) .220 (5.59) .200 (5.08) .300 (7.62) .025 (.64) C637/8 .470 (11.90) .400 (10.20) .270 (6.89) .375 (9.52) .025 (.64) C640/1 .550 (14.00) .280 (7.11) .250 (6.35) .400 (10.16) .025 (.64) C642/3 .500 (12.70) .560(14.22) .200 (5.08) .400 (10.16) .025 (.64) C647/8 .570 (14.50) .500(12.70) .270 (6.89) .475 (12.06) .025 (.64) C657/8 C667/8 .670 (17.02 .600 (15.24) .270 (6.89) .575 (14.60) .025 (.64) .770 (19.56) .720 (18.29) .270 (6.89) .675 (17.14) .025 (.64) ORDERING INFORMATION C 622 C 102 M D R 5 T A CERAMIC CASE SIZE See Table Above High Voltage Golden Max FAILURE RATE A – Not Applicable TERMINATION MATERIAL T – Standard INTERNAL CONSTRUCTION 5 – Standard DIELECTRIC EIA Designation G – C0G (NP0) - Ultra Stable R – X7R - Stable RATED VOLTAGE C – 500 G – 2000 D – 1000 Z – 2500 F – 1500 H – 3000 SPECIFICATION C – Standard CAPACITANCE PICOFARAD CODE Expressed in picofarads (pF). First two digits represent significant figures. Third digit specifies number of zeros. Use 9 for 1.0 thru 9.9 pF. Example 2.2pF = 229 CAPACITANCE TOLERANCE C0G:J – ±5%, K – ±10%; M – ±20% X7R: K – ±10%; M – ±20%; P – 0, -100%; Z – -20,+80% MARKING INFORMATION Voltage Series Front View KEMET K6D Series Back View 102K Capacitance, Tolerance KEMET K6DR 103K Voltage KEMET Dielectric Date Code K6G 102K 1000V 0514 Capacitance, Tolerance Rated Voltage Capacitance, Tolerance Series Voltage C617 & C62X C63X C64X, C65X, C66X For packaging information, see pages 40, and 41. © KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 15 CERAMIC CONFORMALLY COATED/RADIAL HIGH VOLTAGE “GOLDEN MAX” RATINGS & PART NUMBER REFERENCE - COG/NPO Goldmax HV C6XX Series Special Lead Spacing per M49467 - C617 Style Cap Cap Code Cap Tol 1.0pF 1.5 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10 12 15 18 22 27 33 39 47 56 68 82 100 120 150 180 220 270 330 390 470 560 680 820 1000 1200 1500 1800 2200 2700 3300 3900 4700 5600 6800 8200 .010uF .012 .015 .018 .022 .027 .033 .039 .047 .056 .068 .082 .10 109 159 229 279 339 399 479 569 689 829 100 120 150 180 220 270 330 390 470 560 680 820 101 121 151 181 221 271 331 391 471 561 681 821 102 122 152 182 222 272 332 392 472 562 682 822 103 123 153 183 223 273 333 393 473 563 683 823 104 J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M C62X C63X C63X (X=2, 3) (X=7, 8) (X=0,1) (X=7, 8) WVDC 500 1k 1.5k C0G C62X WVDC 2k 3k 500 1k 1.5k WVDC 2k 3k 500 1k 1.5k WVDC 2k 3k 500 1k 1.5k 2k WVDC 2.5k 3k 500 1k 1.5k For packaging information, see pages 40 and 41. 16 © KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 2k 2.5k 3k CERAMIC CONFORMALLY COATED/RADIAL HIGH VOLTAGE “GOLDEN MAX” RATINGS & PART NUMBER REFERENCE - COG/NPO Style Cap Cap Code Cap Tol 1.0pF 1.5 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10 12 15 18 22 27 33 39 47 56 68 82 100 120 150 180 220 270 330 390 470 560 680 820 1000 1200 1500 1800 2200 2700 3300 3900 4700 5600 6800 8200 .010uF .012 .015 .018 .022 .027 .033 .039 .047 .056 .068 .082 .10 109 159 229 279 339 399 479 569 689 829 100 120 150 180 220 270 330 390 470 560 680 820 101 121 151 181 221 271 331 391 471 561 681 821 102 122 152 182 222 272 332 392 472 562 682 822 103 123 153 183 223 273 333 393 473 563 683 823 104 J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M J,K,M C64X C64X C64X C65X C66X (X=0,1) (X=2, 3) (X=7, 8) (X=7, 8) (X=7, 8) WVDC 500 C0G cont. 1k 2k WVDC 3k 500 1k 2k WVDC 3k 500 1k 2k WVDC 3k 500 1k 2k WVDC 3k 500 1k 2k 3k High Voltage Golden Max Goldmax HV C6XX Series Special Lead Spacing per M49467 - For packaging information, see pages 40 and 41. © KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 17 CERAMIC CONFORMALLY COATED/RADIAL HIGH VOLTAGE “GOLDEN MAX” RATINGS & PART NUMBER REFERENCE - X7R Goldmax HV C6XX Series Special Lead Spacing per M49467 - C617 Style Cap 10pF 12 15 18 22 27 33 39 47 56 68 82 100 120 150 180 220 270 330 390 470 560 680 820 1000 1200 1500 1800 2200 2700 3300 3900 4700 5600 6800 8200 .010uF .012 .015 .018 .022 .027 .033 .039 .047 .056 .068 .082 .10 .12 .15 .18 .22 .27 .33 .39 .47 .56 .68 .82 1.0 1.2 1.5 1.8 2.2 2.7 Cap Code Cap Tol 100 120 150 180 220 270 330 390 470 560 680 820 101 121 151 181 221 271 331 391 471 561 681 821 102 122 152 182 222 272 332 392 472 562 682 822 103 123 153 183 223 273 333 393 473 563 683 823 104 124 154 184 224 274 334 394 474 564 684 824 105 125 155 185 225 275 K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z C62X C63X C63X (X=2, 3) (X=7, 8) (X=0,1) (X=7, 8) WVDC 500 1k 1.5k X7R C62X WVDC 2k 500 1k 1.5k WVDC 2k 3k 500 1k 1.5k WVDC WVDC 2k 3k 500 1k 1.5k 2k 2.5k 3k 500 1k 1.5k 2k For packaging information, see pages 40 and 41. 18 © KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 2.5k 3k CERAMIC CONFORMALLY COATED/RADIAL HIGH VOLTAGE “GOLDEN MAX” RATINGS & PART NUMBER REFERENCE - X7R Style Cap 10pF 12 15 18 22 17 33 39 47 56 68 82 100 120 150 180 220 270 330 390 470 560 680 820 1000 1200 1500 1800 2200 2700 3300 3900 4700 5600 6800 8200 .010uF .012 .015 .018 .022 .027 .033 .039 .047 .056 .068 .082 .10 .12 .15 .18 .22 .27 .33 .39 .47 .56 .68 .82 1.0 1.2 1.5 1.8 2.2 2.7 Cap Code Cap Tol 100 120 150 180 220 270 330 390 470 560 680 820 101 121 151 181 221 271 331 391 471 561 681 821 102 122 152 182 222 272 332 392 472 562 682 822 103 123 153 183 223 273 333 393 473 563 683 823 104 124 154 184 224 274 334 394 474 564 684 824 105 125 155 185 225 275 K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z K,M,P,Z C64X C64X C65X C66X (X=0,1) (X=2, 3) (X=7, 8) (X=7, 8) (X=7, 8) WVDC 500 X7R cont. C64X 1k 2k WVDC 3k 500 1k 2k WVDC 3k 500 1k 2k WVDC 3k 500 1k 2k WVDC 3k 500 1k 2k 3k High Voltage Golden Max Goldmax HV C6XX Series Special Lead Spacing per M49467 - For packaging information, see pages 40 and 41. © KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 19 CERAMIC LEADED PACKAGING INFORMATION Ceramic Radial Lead Tape and Reel Packaging KEMET offers standard reeling of Molded and Conformally Coated Radial Leaded Ceramic Capacitors for automatic insertion per EIA specification RS-468. Parts are taped to a tagboard carrier strip, and wound on a reel as shown in Figure 1. Kraft paper interleaving is inserted between the layers of capacitors on the reel. Ammopack is also available, with the same lead tape configuration and package quantities. 12" (30.48 cm) * Figure 1 KEMET Carrier Strip .059" to .315" Greater Than Over All Height of Taped Components KEMET ® ® Adhesive Tape Hub .655" ±0.010" (16.6 ±0.25) 31/4" (82.6) 1/ " 8 (3.18) (Note: Non-standard lead lengths available in bulk only.) Figure 3: Standard Reel C330** C340** C6xx# C315* C320* C056** C066** Kraft Paper Interleaving Carrier Tape CK06** CKR06** C062** CK05** CKR05** C052** C317** C322** C323** C6xx# C333** ∆H P2 P 1MM Max. (.039") H1 D0 P1 H W2 H0 W0 L1 F T P0 Figure 2: Lead Tape Configuration (See Table Below) W Tape Carrier W2 * Lead spacings are 2.54mm (.10") center-to-center. ** Lead spacings are 5.08mm (.20") center-to-center. # See page 15 for exact lead configuration for Series. Ceramic Radial Tape and Reel Dimensions in Millimeters & (Inches) Sprocket Hole Pitch P0 12.7 (.500) ± 0.3 (.012) Nominal Tolerance Dimension Symbol mm (inch) mm (inch) H0 Height to Seating 7301 7303 7301 7303 Plane (formed leads) (2) 16.0 (.630) 18.0 (.709) ±0.5 (.020) Minimum Component Alignment ∆h 4.0 (.157) ±0.2 (.008) Component Pitch P 12.7 (.500) ± 0.3 (.012) Lead Protrusion L1 1.0 (.039) Maximum Lead Spacing (1) F 5.08 2.54 (.20) (.10) 3.81 5.08 (.150) (.200) 6.35 (.250) +0.6 -0.2 (+.024 -.008) ± 0.7 (.028) Composite Tape Thickness Overall Tape and Lead Thickness Carrier Tape Width t 0.7 (.051) ±0.2 (.008) T 1.5 (.059) Maximum W 18.0 (.709) Hold-Down Tape Width Hold-Down Tape Location W0 5.0 (.197) +1.0 - 0.5 (+.039 -.020) Minimum W2 3.0 (.118) Maximum Dimension Sprocket Hole Diameter Sprocket Hole Center to Lead Center (1) Sprocket Hole Center to Component Center Height to Seating Plane (straight leads) (2) Component Height Above Tape Center Symbol Do P1 P2 H H1 Nominal mm (inch) 4.0 (.157) Tolerance mm (inch) ± 0.2 (.008) ± 1.3 (.051) 7301 7303 7301 7303 16.0 (.630) 18.0 (.709) ±0.5 (.020) Minimum 32.2 (1.27) Maximum (1) Measured at the egress from the carrier tape, on the component side. (2) Determined by a 4 digit suffix placed at the end of the part number, as follows: 7301 = Recommended for parts with formed leads. Example: C322C104K5R5CA7301 7303 = Recommended for parts with straight leads. Example: C320C104K5R5CA7303 40 © KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 CERAMIC LEADED PACKAGING INFORMATION CERAMIC PACKAGING C114C-K-G C124C-K-G C192C-K-G C202C-K C222C-K C052C-K-G C062C-K-G C114G C124G C192G C202G C222G C052/56G C062/66G C512G C522G C114T C124T C192T C202T C222T C052/56T C062/66T C31X C32X C33X C340 C350 C410 C412 C420 C430 C440 C512 C522 C617 C622/C623 C627/C628 C630/C631 C637/C638 C640/C641 C642/C643 C647/C648 C657/C658 C667/C668 Military Style CK12, CC75 CK13, CC76 CK14, CC77 CK15 CK16 CK05, CC05 CK06, CC06 CCR75 CCR76 CCR77 CC78-CCR78 CC79-CCR79 CCR05 CCR06 CC07-CCR07 CC08-CCR08 CKR11 CKR12 CKR14 CKR15 CKR16 CKR05 CKR06 N/A N/A Military Specification MIL-C-11015/ MIL-PRF-20 MIL-PRF-20 MIL-PRF-39014 N/A N/A Standard (1) Bulk Quantity 200/Box 200/Box 100/Box 25/Box 10/Tray 100/Bag 100/Bag 200/Box 200/Box 100/Box 25/Box 10/Tray 100/Bag 100/Bag Footnote (2) Footnote (2) 200/Box 200/Box 100/Box 25/Box 10/Tray 100/Bag 100/Bag 500/Bag 500/Bag 250/Bag 100/Bag 50/Bag 300/Box 200/Box 300/Box 200/Box 200/Box Footnote (2) Footnote (2) 500/Bag 500/Bag 500/Bag 250/Bag 250/Bag 100/Bag 100/Bag 100/Bag 50/Bag 50/Bag Ammo Pack Quantity Maximum 2000 1500 2500 2500 1500 1000 N/A 4000 4000 4000 2000 2000 Maximum Reel Quantity 5000 5000 3000 500 300 2000 1500 5000 5000 3000 500 300 1700 1500 N/A N/A 5000 5000 3000 500 300 1700 1500 2500 2500 1500 1000 N/A 5000 5000 5000 2500 2500 N/A N/A Reel Size 12" 12" 12" 12" 12" 12" 12" 12" 12" 12" 12" 12" 12" 12" N/A N/A 12" 12" 12" 12" 12" 12" 12" 12" 12" 12" 12" N/A 12" 12" 12" 12" 12" N/A N/A Tape and Reel Packaging KEMET Series NOTE: (1) Standard packaging refers to number of pieces per bag, tray or vial. (2) Quantity varies. For further details, please consult the factory. © KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 41