IDPC-25 25W Constant Current Mode LED Driver series SELV ■ Features Constant Current mode output Flicker free design PCB type design Built-in active PFC function No load power consumption<0.5W(Blank-Type) Function options: 2 in 1 dimming (dim-to-off); ■ Applications LED panel lighting LED flood lighting Indoor LED lighting Auxiliary DC output 3 years warranty ■ Description IDPC-25 series is a 25W PCB type LED AC/DC driver featuring the constant current mode output with flicker free design. IDPC-25 operates from 90~295VAC and offers models with different rated current ranging between 350mA and 1050mA. Thanks to the efficiency up to 82%, with the fanless design, the entire series is able to operate for -20℃~+50℃ ambient temperature under free air convection. IDPC-25 is equipped with various function options, such as dimming methodologies, so as to provide the optimal design flexibility for lighting system. ■ Model Encoding IDPC - 25 A - 350 Rated output current(350/500/700/1050mA) Function options Rated wattage Series name Type Blank A Function 2 in 1 dimming (0~10VDC and 10V PWM) 2 in 1 dimming and Auxiliary DC output Note In Stock In Stock File Name:IDPC-25-SPEC 2017-04-26 IDPC-25 25W Constant Current Mode LED Driver series SPECIFICATION IDPC-25 -350 IDPC-25 -500 IDPC-25 -700 IDPC-25 -1050 RATED CURRENT 350mA 500mA 700mA 1050mA RATED POWER 24.5W 25W 25.2W 25.2W CONSTANT CURRENT REGION Note.2 49 ~ 70V 35 ~ 50V 25.2 ~ 36V 16.8 ~ 24V OPEN CIRCUIT VOLTAGE(max.) 100V 75V 63V 36V MODEL OUTPUT CURRENT RIPPLE 5.0% max. @rated current CURRENT TOLERANCE ±7.0% SETUP TIME 500ms / 230VAC 1200ms/115VAC Note.4 AUXILIARY DC OUTPUT Note.5 Nominal 12V(deviation 11.4~12.6)@50mA for A-Type only VOLTAGE RANGE Note.3 FREQUENCY RANGE INPUT 90 ~ 295VAC 127 ~ 417VDC (Please refer to "STATIC CHARACTERISTIC" section) 47 ~ 63Hz POWER FACTOR (Typ.) PF>0.95/115VAC, PF>0.92/230VAC, PF>0.9/277VAC@full load (Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section) TOTAL HARMONIC DISTORTION THD< 20%(@load≧70%/115VAC,230VAC; @load≧75%/277VAC) (Please refer to “TOTAL HARMONIC DISTORTION” section) EFFICIENCY (Typ.) 82% AC CURRENT 0.4A/115VAC 0.16A/230VAC INRUSH CURRENT (Typ.) COLD START 30A(twidth=100μs measured at 50% Ipeak) at 230VAC; Per NEMA 410 81.5% 81.5% 80% 0.13A/277VAC MAX. No. of PSUs on 16A 32 units (circuit breaker of type B) / 32 units (circuit breaker of type C) at 230VAC CIRCUIT BREAKER LEAKAGE CURRENT <0.75mA / 277VAC NO LOAD POWER CONSUMPTION <0.5W for Blank-Type, <1.2W for A-Type PROTECTION SHORT CIRCUIT Hiccup mode, recovers automatically after fault condition is removed WORKING TEMP. Ta=-20 ~ +50℃ (Please refer to “ OUTPUT LOAD vs TEMPERATURE” section) WORKING HUMIDITY 20 ~ 90% RH non-condensing ENVIRONMENT STORAGE TEMP., HUMIDITY -40 ~ +80℃, 10 ~ 95% RH TEMP. COEFFICIENT ±0.03%/℃ (0 ~ 50℃) VIBRATION 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes SAFETY STANDARDS WITHSTAND VOLTAGE UL8750,CSA C22.2 NO.250.13-12;ENEC EN61347-1 & EN61347-2-13 independent, EN62384, GB19510.1,GB19510.14 approved I/P-O/P:3.75KVAC SAFETY & ISOLATION RESISTANCE I/P-O/P:100M Ohms / 500VDC / 25℃/ 70% RH EMC Compliance to EN55015, EN61000-3-2 Class C (@load≧70%) ; EN61000-3-3,GB17743,GB17625.1 EMC EMISSION EMC IMMUNITY MTBF OTHERS DIMENSION PACKING NOTE Compliance to EN61000-4-2,3,4,5,6,8,11; EN61547, light industry level( surge immunity:Line-Line:1KV ) 418.9Khrs min. MIL-HDBK-217F (25℃) 114.5*72.5*20mm(L*W*H) 0.12Kg; 72pcs / 9.64Kg / 1.13CUFT 1. All parameters NOT specially mentioned are measured at 230VAC input, rated current and 25℃ of ambient temperature. 2. Please refer to "DRIVING METHODS OF LED MODULE". 3. De-rating may be needed under low input voltages. Please refer to STATIC CHARACTERISTIC sections for details. 4. Length of set up time is measured at cold first start. Turning ON/OFF the driver may lead to increase of the set up time. 5. There is no design of short circuit protection for the Auxiliary DC output; this function can not be used when dimming input terminals(DIM+,DIM-) are short circuit or when it is no load or short circuit at output(Vo+,Vo-). 6. The driver is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again. File Name:IDPC-25-SPEC 2017-04-26 IDPC-25 25W Constant Current Mode LED Driver series Block Diagram fosc : 70KHz AUX+(for A-Type) AUX-(for A-Type) RECTIFIERS I/P EMI FILTER & RECTIFIERS RECTIFIERS & FILTER POWER SWITCHING O.L.P. PWM&PFC CONTROL CURRENT LIMIT Vo+ VoDIM+ DIM- DETECTION CIRCUIT DRIVING METHODS OF LED MODULE ※ This series works in constant current mode to directly drive the LEDs. In the constant current region, the highest voltage at the output of the driver depends on the configuration of the end systems. 100 Vo(%) Constant Current area Should there be any compatibility issues, please contact MEAN WELL. 70 (min.) Hiccup Protection 50 100 Io(%) Typical output current normalized by rated current (%) File Name:IDPC-25-SPEC 2017-04-26 IDPC-25 25W Constant Current Mode LED Driver series DIMMING OPERATION ※ 2 in 1 dimming function + HS1 AC/L TB1 AC/L AC/N AC/N DIMDIM+ - TB2 - VoVo+ + + Output constant current level can be adjusted by applying one of the two methodologies between DIM+ and DIM-: 0 ~ 10VDC, or 10V PWM signal. Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers. ◎ Applying additive 0 ~ 10VDC 100% 90% Vo- + + - - DIM+ + Output current (%) 80% Vo+ 70% 60% 50% 40% 30% Additive Voltage - 20% DIM- 10% “DO NOT connect "DIM- to Vo- ” 0% 0V 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V Dimming input: Additive voltage ◎ Applying additive 10V PWM signal (frequency range 300Hz ~ 3KHz): 100% 90% Vo- + + - - DIM+ Additive PWM signal Output current (%) 80% Vo+ 70% 60% 50% 40% 30% 20% DIM“DO NOT connect "DIM- to Vo- ” 10% 0% 0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% Duty cycle of additive 10V PWM signal dimming input Note : 1. Min. dimming level is about 8% and the output current is not defined when 0%< I out<8%. 2. The output current could drop down to 0% when dimming input is about 0Vdc or 10V PWM signal with 0% duty cycle. File Name:IDPC-25-SPEC 2017-04-26 IDPC-25 25W Constant Current Mode LED Driver series OUTPUT LOAD vs TEMPERATURE 100 80 LOAD (%) 60 40 20 -20 -10 0 5 15 25 35 45 50 (HORIZONTAL) AMBIENT TEMPERATURE,Ta (℃) STATIC CHARACTERISTIC POWER FACTOR (PF) CHARACTERISTIC 1 90 0.98 80 0.96 70 0.94 PF LOAD (%) 100 60 277V 230V 115V 0.92 50 0.9 40 90 100 135 180 0.88 70% 295 200 80% 90% 100% (25W) INPUT VOLTAGE (V) LOAD ※ De-rating is needed under low input voltage. TOTAL HARMONIC DISTORTION (THD) EFFICIENCY vs LOAD IDPC-25 series possess superior working efficiency that up to 82% can be reached in field applications. ※ 350mA Model ※ 350mA Model 86 17% 84 THD(%) 13% 277VAC 230VAC 115VAC 11% 9% 7% 82 80 277V 78 230V 115V 76 74 5% 3% 70% EFFICIENCY(%) 15% 72 80% 90% LOAD 100% 70 70% 80% 90% 100% LOAD File Name:IDPC-25-SPEC 2017-04-26 IDPC-25 25W Constant Current Mode LED Driver series MECHANICAL SPECIFICATION 114.5 ※ Blank-Type Unit:mm 4 7 106.5 - 4 *ψ 3. 5 + HS1 58.5 72.5 AC/L TB1 AC/L AC/N AC/N DIMDIM+ - TB2 - VoVo+ 20 + + Terminal Pin No. Assignment(TB1) Pin No. 1 2 3 4 Assignment ACL ACL ACN ACN Terminal Pin No. Assignment(TB2) Pin No. 1 2 3 4 ※ A-Type Assignment DIMDIM+ VoVo+ 114.5 4 7 106.5 - 4 *ψ 3. 5 + HS1 - 58.5 - 20 DIM- TB2 DIM+ AuxAux+ VoVo+ + + 72.5 AC/L TB1 AC/L AC/N AC/N Terminal Pin No. Assignment(TB1) Pin No. 1 2 3 4 Assignment ACL ACL ACN ACN Terminal Pin No. Assignment(TB2) Pin No. 1 2 3 Assignment DIMDIM+ AUX- Pin No. 4 5 6 Assignment AUX+ VoVo+ Installation Manual Please refer to : http://www.meanwell.com/manual.html File Name:IDPC-25-SPEC 2017-04-26