3.2x2.4mm SMD CHIP LED LAMP Part Number: APBD3224LVBDSEKJ3C ATTENTION Blue Hyper Red OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Features Descriptions z 3.2x2.4mm SMD LED, 2.4mm thickness. z The Blue source color devices are made with InGaN Light Emitting Diode. z Low power consumption. z Ideal for backlight and indicator. z The Hyper Red device is based on light emitting diode chip made from AlGaInP. z Package : 1500pcs / reel. z Moisture sensitivity level : level 3. z Low current IF=2mA operating. z Electrostatic discharge and power surge could damage the LEDs. z It is recommended to use a wrist band or anti- z RoHS compliant. electrostatic glove when handling the LEDs. z All devices, equipments and machineries must be electrically grounded. Package Dimensions BLUE RED Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.1(0.004") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAO4734 REV NO: V.1A DATE: AUG/12/2015 PAGE: 1 OF 6 APPROVED: Wynec CHECKED: Allen Liu DRAWN: M.Liu ERP: 1203015181 Selection Guide Part No. Emitting Color (Material) Blue (InGaN) APBD3224LVBDSEKJ3C Viewing Angle [1] Iv (mcd) [2] @ 2mA Lens Type Water Clear Hyper Red (AlGaInP) Min. Typ. 50 100 *50 *100 120 250 *30 *50 2θ1/2 20° Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity / luminous Flux: +/-15%. * Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Emitting Color λpeak Peak Wavelength Blue Hyper Red λD [1] Dominant Wavelength Δλ1/2 Min. Typ. Units Test Conditions 465 640 nm IF=2mA Blue Hyper Red 470 625 nm IF=2mA Spectral Line Half-width Blue Hyper Red 22 20 nm IF=2mA C Capacitance Blue Hyper Red 100 27 pF VF=0V;f=1MHz VF [2] Forward Voltage Blue Hyper Red 3.0 2.1 V IF=2mA IR Reverse Current Blue Hyper Red 50 10 uA VR = 5V 2.2 1.5 Max. 2.65 1.8 Notes: 1. Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. 3. Wavelength value is traceable to the CIE127-2007 compliant national standards. 4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25°C Parameter Blue Hyper Red Units Power dissipation 90 63 mW DC Forward Current 30 30 mA Peak Forward Current [1] 100 150 mA Electrostatic Discharge Threshold (HBM) 250 3000 V Reverse Voltage 5 Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C V Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAO4734 REV NO: V.1A DATE: AUG/12/2015 PAGE: 2 OF 6 APPROVED: Wynec CHECKED: Allen Liu DRAWN: M.Liu ERP: 1203015181 APBD3224LVBDSEKJ3C Blue SPEC NO: DSAO4734 REV NO: V.1A DATE: AUG/12/2015 PAGE: 3 OF 6 APPROVED: Wynec CHECKED: Allen Liu DRAWN: M.Liu ERP: 1203015181 Hyper Red SPEC NO: DSAO4734 REV NO: V.1A DATE: AUG/12/2015 PAGE: 4 OF 6 APPROVED: Wynec CHECKED: Allen Liu DRAWN: M.Liu ERP: 1203015181 APBD3224LVBDSEKJ3C Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Reel Dimension Tape Dimensions (Units : mm) SPEC NO: DSAO4734 REV NO: V.1A DATE: AUG/12/2015 PAGE: 5 OF 6 APPROVED: Wynec CHECKED: Allen Liu DRAWN: M.Liu ERP: 1203015181 PACKING & LABEL SPECIFICATIONS APBD3224LVBDSEKJ3C Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAO4734 REV NO: V.1A DATE: AUG/12/2015 PAGE: 6 OF 6 APPROVED: Wynec CHECKED: Allen Liu DRAWN: M.Liu ERP: 1203015181