Click on Series name for product info on aimtec.com Series AM3T-NZ 3 Watt | DC-DC Converter FEATURES: • • • • • Models Single output Model AM3T-0505S-NZ AM3T-0512S-NZ AM3T-0515S-NZ Input Voltage (V) 4.5-9 4.5-9 4.5-9 Models Dual output Model AM3T-0505D-NZ AM3T-0512D-NZ AM3T-0515D-NZ • Operating temperature -40oC to + 85oC • Input / Output Isolation 1500VDC • Pin compatible with multiple manufacturers • Continuous short circuit protection RoHS compliant 24 Pin DIP Package Shielded metal package High efficiency up to 78% Wide 2:1 input range Input Voltage (V) 4.5-9 4.5-9 4.5-9 Output Voltage (V) Output Current max (mA) Isolation (VDC) 5 12 15 600 250 200 1500 1500 1500 Output Voltage (V) Output Current max (mA) Isolation (VDC) ±300 ±125 ±100 1500 1500 1500 ±5 ±12 ±15 Max. Cap. Load (µF) Efficiency (%) 4700 2700 2200 74 77 77 Max. Cap. Load (µF) Efficiency (%) 2200 1800 1000 76 78 78 NOTE: All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. Input Specifications Parameters Voltage range Filter Absolute Maximum Isolation Specifications Parameters Tested I/O voltage Resistance Capacitance Output Specifications Parameters Voltage accuracy Dual Output Voltage Balance Short Circuit protection Short circuit restart Line voltage regulation Load voltage regulation Temperature coefficient Ripple& Noise Transient Recovery Time Transient Deviation www.aimtec.com F 051e R6.D Nominal Typical 5 4.5-9 π (Pi) Network 12 5 Vin Conditions 60 sec Maximum Conditions Maximum Typical Maximum ±1 ±0.5 Balanced Loads Continuous Auto-recovery ±0.2 ±0.2 ±0.03 75 0.5 ±2 20MHz bandwidth 25% Load Step 25% Load Step Tel: +1 514 620 2722 1 of 3 VDC VDC Typical 1500 > 1000 120 Units 5 Vin Units VDC MOhm pF Units % % % % %/oC mV p-p m sec % Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM3T-NZ 3 Watt | DC-DC Converter Parameters Conditions Switching frequency Operating temperature Storage temperature Max Case temperature Temperature Rise Cooling Humidity Case material Weight Dimensions (L x W x H) MTBF No pin -V Input -V Input No pin No pin N.C. No pin +V Output No pin -V Output V+ Input V+ Input No pin -40 to +85 -55 to +125 Units KHz o C o C o C o C 100 25oC o 300 Free air convection C % g Dimensions 1500VDC Dual 32.00 (1.26) No pin -V Input -V Input Common No pin -V Output No pin +V Output No pin Common +V Input +V Input No pin 23.03 (0.91) 0.50 (0.02) 2 20.00 (0.80) Single Maximum 95 Black Anodized Aluminum 14 1.26 x 0.80 x 0.42 inches 32. 00 x 20.00 x 10.80mm >1 000000 hrs(MIL-HDBK -217F, Ground Benign, t=+25oC) Pin Out Specifications 1 2 3 9 10 11 12/13 14 15 16 22 23 24 200 Full Load, 25oC 1.5mm from case for 10 Seconds Lead Temperature Pin Typical 100% load With derating above +85C 3 9 11 Bottom View 23 22 Built-in Stand-offs to ease PCB cleaning 4.10 (0.16) 10.80 (0.42) N.C.: not connected 14 5.08 (0.20) 2.54 (0.10) Printed Face 16 15.24 (0.60) General Specifications Filtering Single output External capacitors Vin (VDC) Cin) (uF) 5 100 www.aimtec.com F 051e R6.D Vout (VDC) 5 12 15 Filtering Dual output Cout (uF) 10 10 10 Tel: +1 514 620 2722 2 of 3 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM3T-NZ 3 Watt | DC-DC Converter Recommended Circuit Single Output C1 + C2 - Vin Optional Surge Circuit Model C1 Optional Filter Circuit C2 C4 5 Vin 4.7 µF / 50V 4.7 µF / 50V Note: Fuse is user selectable DC DC TVS LDM 1 nF /2KV 12 µH Load C3 MOV +Vout LDM LDM2 + Vin FUSE C4 MOV - - Vout TVS SMCJ16A C3 680µF / 25V LDM2 - Derating Free Air Convection 85º C Output Power (%) 100 80 60 Safe Operating Area 40 20 0 - 40 - 20 0 20 40 60 80 85 105 100 Ambient Temperature º C NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3.Mechanical drawings and specifications are for reference only. 4.All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5.Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com. www.aimtec.com F 051e R6.D Tel: +1 514 620 2722 3 of 3 Toll free: + 1 888 9 AIMTEC (924 6832) North America only