LE150S-CD 150W Single Output LED Driver Series Features High Efficiency (up to 93%) Wide Range Universal Input 90-305 VAC Active Power Factor Correction (0.99 typical) Constant Current Output Dimming Function Lightning Protection Waterproof (IP67) Overcurrent, Overvoltage, Overtemperature Protection Meets UL8750 & EN61347 Safety 3 Year Warranty Description The LE150S-CD Series operate from a 90 ~ 305Vac input range. These units will provide up to a 1.4 A of output current and a maximum output voltage of 214Vdc for 150 W maximum output power. They are designed to be highly efficient and highly reliable. The standard features include dimming control, lightning protection, over voltage protection, short circuit protection, and over temperature protection. Model Selection Model Number Output Current Output Voltage LE150S140CD 1330mA-1470mA 53V – 107V 89%-90% 91%-92% 3.2V pk-pk max. ±1% ±3% 128V – 161V LE150S70CD 665mA-735mA 107V – 214V 90%-91% 92%-93% 6.5V pk-pk max. ±1% ±3% 257V – 321V Notes: Efficiency* 110Vac 220Vac Ripple & Noise** Regulation Line Load Overvoltage Trip Level 1. Efficiency measured at full load, at input voltage noted. 2. Measured at 20MHz bandwidth, with noise probe directly across output terminals, and load terminated with 0.1µF ceramic and 10µF low ESR electrolytic capacitors. General Specifications AC Input Input Current Inrush Current Input Fuses Earth Leakage Current Efficiency Output Power www.slpower.com Turn On Time 90-305Vac, 47-63Hz, 1∅ 100Vac: 1.8A, 220Vac: 0.9A 230Vac, cold start: will not exceed 65A XA, 250VAC fuses provided on all models <0.75mA@277Vac, 50Hz See Models chart. Dimming Function Overload Protection Short Circuit Protection 2.0 seconds, max. 1-10Vdc source or External Resistor can be used for dimming control. See below. Constant Current Provided - no damage to unit, self-recovery. Overvoltage Protection Latch mode. AC input will need to be reset to return to normal operation after an OVP condition. See chart for trip range. Overtemperature Protection Latch mode. AC input will need to be reset To return to normal operation after an OTP condition. Trip Temperature = 110°C typical. 150W continuous LE150S-CD REV 2.0, 11-FEB-13 1 LE150S-CD 150W Single Output LED Driver Series General Specifications (continued) Ripple and Noise See chart Operating Temperature Output Voltage See chart Relative Humidity 10% to 100% operating 5% to 100%, non-operating +/- 3%. See chart Safety Standards UL8750, UL935, UL1012, CSA-C22.2 No. 107.1, EN61347-1, EN61347-2-13 Total Regulation Dimensions Weight MTBF 340,000 hours (1400mA model, 110Vac input, 80% load, 25°C ambient, per MIL-HDBK-217F). Lifetime 58,000 hours (1400mA model, at 110Vac input, 80% load, 45°C ambient temperature). W: 3.13” x L: 9.37” x H: 1.81” 1500g Operating: -35°C to +70°C Non-operating: -40°C to +85°C EMI/EMC Compliance Emissions EN55015, Radiated & Conducted with 6db of margin EMI for Lighting Equipment EN61547 Static Discharge Immunity EN61000-4-2, 4kV Contact Discharge, 8kV air discharge Radiated RF Immunity EN61000-4-3 EFT/Burst Immunity EN61000-4-4 Line Surge Immunity EN61000-4-5, 2kV line-line, 4kV line-earth Conducted RF Immunity EN61000-4-6 Power Frequency Magnetic Field Immunity EN61000-4-8 Voltage Dip Immunity EN61000-4-11 Line Harmonic Emissions EN61000-3-2 Flicker Test EN61000-3-3 Derating Curves Mechanical Drawing www.slpower.com LE150S-CD REV 2.0, 11-FEB-13 2 LE150S-CD 150W Single Output LED Driver Series Dimming Control The dimming function shown below uses an internal pull-up resistor, with the output at full load when the dimming leads are not connected (floated). Parameters: Parameter Min. Typ. Max. 10V Output Voltage 9.8V 10V 10.2V 10V Output Source Current 0mA - 10mA Absolute Max. Voltage on the 1-10V input -2V - 12V Source Current on the 1-10V input 0mA - 1mA Value of Rin (resistor inside the LED Driver, which is located between the 1-10V input and 10V output 19.8K 20K 20.2K www.slpower.com LE150S-CD REV 2.0, 11-FEB-13 Notes 3 LE150S-CD 150W Single Output LED Driver Series LE150SXXXCD Dimming Configuration using External Voltage LE150SXXXCD Dimming Configuration using External Resistance Dimming Control Notes: 1. Io is actual output current and Ir is rated current without dimming control. 2. For the driver to operate properly, the load voltage must be maintained above the minimum voltage threshold (approx. 50% of the max. output voltage for any given model). 3. If the output voltage is maintained above 50% of the maximum output voltage, the dimming control may be operated over the entire 1-10V range with output current varying from 100% down to practically 10%. 4. The dimming signal is allowed to be less than 1V, however, when it for 0-1V, the output current is 10% Io. 5. The internal resistor Rin is 20K, and Vcc is about 15V. 6. Do not connect the GND of dimming to the output; otherwise, the LED driver cannot work normally. Data Sheet © 2012 SL Power Electronics Corp. The information and specifications contained herein are believed to be correct at the time of publication. However, SL Power accepts no responsibility for consequences arising from reproduction errors or inaccuracies. Specifications are subject to change without notice. www.slpower.com LE150S-CD REV 2.0, 11-FEB-13 4