Finisar Product Specification 2 Gigabit RoHS Compliant Long-Wavelength 2x5 Pin SFF Transceiver FTLF1319F1xTL PRODUCT FEATURES • Up to 2.125Gb/s bi-directional data links • Standard 2x5 pin SFF footprint (MSA compliant) • 1310nm Fabry-Perot laser transmitter • Duplex LC connector • RoHS compliant and Lead Free • Very low jitter • Up to 10 km on 9/125μm SMF • Metal enclosure, for lower EMI • 1.25 Gb/s 1000Base-LX Ethernet • Single 3.3V power supply • • Low power dissipation <700mW Dual Rate 1.063 / 2.125 Gb/s Fibre Channel • Industrial operating temperature range: -40°C to 85°C APPLICATIONS Finisar’s FTLF1319F1xTL Small Form Factor (SFF) transceivers comply with the 2x5 standard package defined by the Small Form Factor Multi-Sourcing Agreement (MSA)1. They are simultaneously compatible with Gigabit Ethernet as specified in IEEE Draft P802.3z/D5.02 and Fibre Channel FC-PH, PH2, PH33 and FC-PI-2 10.04. They are RoHS compliant and lead-free per Directive 2002/95/EC5 and Finisar Appl. Note AN-2038. PRODUCT SELECTION FTLF1319F1xTL x G M K H 2 Grounding Pins, Short EMI shield 6 Grounding Pins, Short EMI shield 2 Grounding Pins, Long EMI shield 6 Grounding Pins, Long EMI shield © Finisar Corporation March 30, 2006 Rev. D Page 1 Finisar FTLF1319F1xTL 2x5 Pin SFF Product Specification – March 2006 I. Pin Descriptions Pin MS Symbol MS 1 2 3 4 5 6 7 8 9 10 VEER VCCR SD RDRD+ VCCT VEET TDIS TD+ TD- Name/Description Mounting Studs are for mechanical attachment. Chassis ground is internally isolated from circuit ground. Connection to chassis ground is recommended. Receiver Ground (Common with Transmitter Ground) Receiver Power Supply Signal Detect. Logic 1 indicates normal operation. Receiver Inverted DATA out. AC Coupled. Receiver Non-inverted DATA out. AC Coupled Transmitter Power Supply Transmitter Ground (Common with Receiver Ground) Transmitter Disable Transmitter Non-Inverted DATA in. AC Coupled. Transmitter Inverted DATA in. AC Coupled. Logic Family NA NA NA LVTTL See Rx spec. See Rx spec. NA NA LVTTL See Tx spec See Tx spec. MS 10 9 8 7 6 TOP VIEW 12345 MS II. Absolute Maximum Ratings Parameter Maximum Supply Voltage Storage Temperature Case Operating Temperature Relative Humidity Lead Soldering Temperature/Time Symbol Vcc TS TA RH Min 0.5 -40 -40 0 Typ Max 5.0 85 85 85 260/10 Unit V °C °C % °C/s Ref. 1 Notes: 1. Non condensing. © Finisar Corporation March 30, 2006 Rev. D Page 2 Finisar FTLF1319F1xTL 2x5 Pin SFF Product Specification – March 2006 Electrical Characteristics (TA = -40 to 85 °C, VCC = 3.0 to 3.60 Volts) III. Parameter Supply Voltage Supply Current Transmitter Input differential impedance Single ended data input swing Transmit Disable Voltage Transmit Enable Voltage Transmit Disable Assert Time Receiver Single ended data output swing Data output rise time Data output fall time Signal Detect Normal Signal Detect Fault Power Supply Rejection Deterministic Jitter Contribution (p-p) Total Jitter Contribution (p-p) Notes: 1. 2. 3. 4. 5. 6. 7. 8. Symbol Vcc Icc Min 3.00 Rin Vin,pp VD VEN Typ Max 3.60 300 Unit V mA Ref. Ω mV V V us 1 1200 Vcc Vee+ 0.8 10 50 mV ps ps V V mVpp ps 3 4 4 5 5 6 7 120 ps 8 100 250 Vcc – 1.3 Vee Vout,pp tr tf VSD norm VSD fault PSR RX ∆DJ 300 100 100 Vcc – 0.5 Vee 100 RX ∆TJ 800 175 175 Vcc Vee+0.5 2 AC coupled. Or open circuit. Into 100 Ω differential termination. 20 – 80 % Signal detect is LVTTL. Logic 1 indicates normal operation; logic 0 indicates no signal detected. Receiver sensitivity is compliant with power supply sinusoidal modulation of 20 Hz to 1.5 MHz up to specified value applied through the recommended power supply filtering network. Measured with DJ-free data input signal. In actual application, output DJ will be the sum of input DJ and ∆DJ. If measured with TJ-free data input signal. In actual application, output TJ will be given by: TJ OUT = DJ IN + ΔDJ + (TJ IN − DJ IN ) + (ΔTJ − ΔDJ ) © Finisar Corporation March 30, 2006 Rev. D 2 2 Page 3 Finisar FTLF1319F1xTL 2x5 Pin SFF Product Specification – March 2006 Optical Characteristics (TA = -40 to 85 °C, VCC = 3.0 to 3.60 Volts) IV. Parameter Transmitter Output Opt. Power Optical Wavelength Spectral Width Optical Modulation Amplitude Optical Rise/Fall Time RIN Deterministic Jitter Contribution Total Jitter Contribution Extinction Ratio Receiver Receiver Sensitivity = 1.06 Gb/s Receiver Sensitivity = 2.125 Gb/s Receiver Sensitivity = 1.25 Gb/s Stressed RX sens. =1.0625 Gb/s Stressed RX sens. =2.125 Gb/s Stressed RX sens. =1.25 Gb/s Average Received Power Receiver Elec. 3 dB cutoff freq. Optical Center Wavelength Return Loss Signal Detect Assert Signal Detect De-Assert Signal Detect Hysteresis Symbol Min POUT λ σ OMA tr/ tf -9.5 1270 Typ Max Unit -3 1355 3 dBm nm nm μW ps dB/Hz ps ps 1 2 2 2,3 4 dBm dBm dBm mW mW dBm dBm MHz nm dB dBm dBm dB 7, 8 7, 8 7, 8 174 100 TX ∆DJ TX ∆TJ ER 20 <65 160 -120 56.5 119 Ref. 5 6 9 RxSENS RxSENS RxSENS -22 -21 -22 0.055 0.096 -18 -14.5 0 1500 1600 -23 -25 -19 RxMAX λC 1270 12 PA PD P A - PD -30 0.5 Notes: 1. Class 1 Laser Safety per FDA/CDRH and IEC-825-1 regulations. 2. Also specificied to meet curves in FC-PI-2 10.0 Figures 18 and 19, which allow trade-off between wavelength, spectral width and OMA. 3. Equivalent extinction ratio specification for Fibre Channel. Allows smaller ER at higher average power. 4. Unfiltered, 20-80%. Complies with IEEE 802.3 (Gig. E), FC 1x and 2x eye mask when filtered. 5. Measured with DJ-free data input signal. In actual application, output DJ will be the sum of input DJ and ∆DJ. 6. If measured with TJ-free data input signal. In actual application, output TJ will be given by: TJ OUT = DJ IN + ΔDJ + 7. 8. (TJ IN − DJ IN ) + (ΔTJ − ΔDJ ) 2 2 Measured with conformance signals defined in FC-PI-2 10.0 specifications. Measured with PRBS 27-1 at 10-12 BER. © Finisar Corporation March 30, 2006 Rev. D Page 4 Finisar FTLF1319F1xTL 2x5 Pin SFF Product Specification – March 2006 V. General Specifications Parameter Data Rate Bit Error Rate Max. Supported Link Length on 9/125μm SMF @ 2x Fibre Channel Max. Supported Link Length on 9/125μm SMF @ Gigabit Ethernet Symbol BR Min Typ 1.0625, 1.25, 2.125 Max Units Gb/sec 1 10-12 Ref. BER LMAX1 10 km 2 3 LMAX1 10 km 4 Notes: 1. Gigabit Ethernet and 1x, 2x Fibre Channel compatible, per IEEE 802.3 and FC-PI-2 10.0, respectively. Typical maximum data rate extends to 2.5Gb/s. 2. Tested with PRBS 27-1 test pattern. 3. Dispersion limited per FC-PI-2 10.0 4. Attenuation of 0.55 dB/km is used for the link length calculations. Distances are indicative only. Please refer to the Optical Specifications in Table IV to calculate a more accurate link budget based on specific conditions in your application. VI. Environmental Specifications Finisar SFF transceivers have an extended operating temperature range from –40°C to +85°C case temperature. Parameter Case Operating Temperature Storage Temperature VII. Symbol Top Tsto Min -40 -40 Typ Max 85 85 Units °C °C Ref. Regulatory Compliance Finisar transceivers are Class 1 Laser Products and comply with US FDA regulations. These products are certified by TÜV and CSA to meet the Class 1 eye safety requirements of EN (IEC) 60825 and the electrical safety requirements of EN (IEC) 60950. Copies of certificates are available at Finisar Corporation upon request. © Finisar Corporation March 30, 2006 Rev. D Page 5 FTLF1319F1xTL 2x5 Pin SFF Product Specification – March 2006 Finisar VIII. Mechanical Specifications Finisar’s Small Form Factor (SFF) transceivers comply with the standard dimensions defined by the Small Form Factor Multi-Sourcing Agreement (MSA). FTLF1319F1GTL © Finisar Corporation March 30, 2006 Rev. D Page 6 FTLF1319F1xTL 2x5 Pin SFF Product Specification – March 2006 Finisar FTLF1319F1MTL © Finisar Corporation March 30, 2006 Rev. D Page 7 FTLF1319F1xTL 2x5 Pin SFF Product Specification – March 2006 Finisar FTLF1319F1HTL © Finisar Corporation March 30, 2006 Rev. D Page 8 FTLF1319F1xTL 2x5 Pin SFF Product Specification – March 2006 IX. Finisar PCB Layout and Bezel Recommendations Minimum Recommended Pitch is 0.600” © Finisar Corporation March 30, 2006 Rev. D Page 9 FTLF1319F1xTL 2x5 Pin SFF Product Specification – March 2006 X. Finisar References 1. Small Form Factor (SFF) Transceiver Multi-source Agreement (MSA). January 6, 1998. 2. “IEEE Draft P802.3z/D5.0 ‘Media Access Control (MAC) Parameters, Physical Layer, Repeater and Management Parameters for 1000Mb/s Operation’”. IEEE Standards Department, 1998. 3. “Fibre Channel Physical and Signaling Interface (FC-PH, FC-PH2, FC-PH3)”. American National Standard for Information Systems. 4. “Fibre Channel Draft Physical Interface Specification (FC-PI-2 10.0)”. American National Standard for Information Systems. 5. Directive 2002/95/EC of the European Council Parliament and of the Council, “on the restriction of the use of certain hazardous substances in electrical and electronic equipment.” January 27, 2003. XI. For More Information Finisar Corporation 1389 Moffett Park Drive Sunnyvale, CA 94089-1133 Tel. (408) 548-1000 Fax (408) 541-6138 [email protected] www.finisar.com © Finisar Corporation March 30, 2006 Rev. D Page 10